Local regulations may restrict the use of this product to below the conditions quoted.

In the interests of development and improvement of the product, we reserve the right to change the specification without notice. © Copyright 2018

TI-P133-06
CMGT Issue 20

M10S
Ball Valve
DN¼" to DN2½"

Description
The M10S three-piece body ball valve has been designed for use as an isolating valve,
not a control valve, and can be serviced without removal from the pipeline (screwed and
welded versions only). It can be used with the majority of industrial fluids for services
ranging from vacuum to the higher temperatures and pressures.

Available types
M10S2_ _ Zinc plated carbon steel body, PDR 0.8 seats.

M10S3_ _ Stainless steel body, PDR 0.8 seats.

M10S4_ _ Complete stainless steel, PDR 0.8 seats.

Note: The nomenclature will be followed with either FB (full bore) or RB (reduced bore).

Standards
This product fully complies with the requirements of the Pressure Equipment Directive (PED) and carries the mark when so
required.

Certification
This product is available with certification to EN 10204 3.1.
Note: All certification/inspection requirements must be stated at the time of order placement.

Sizes and pipe connections

Full bore Flanged
¼", 3/8", ½", ¾", 1", 1¼", 1½" and 2"
DN15 to DN50
Screwed and welded
ASME Class 150, ASME Class 300, and EN 1092 PN40.
BSP, BSPT, API/NPT, BW, SW

Reduced bore Flanged

¼", 3/8", ½", ¾", 1", 1¼", 1½", 2" and 2½"
DN15 to DN65
Screwed and welded
ASME Class 150, ASME Class 300, and EN 1092 PN40.
BSP, BSPT, API/NPT, BW, SW

Page 1 of 7
Technical data
Flow characteristic Modified linear

Port Full and reduced port versions

Leakage test procedure to ISO 5208 (Rate A)/EN 12266-1 (Rate A)

Antistatic device Complies with ISO 7121 and BS 5351

Pressure/temperature limits

A
Temperature °C
E
D
Steam
saturation
curve
F E D C B

Pressure bar g

The product must not be used in this region.

A - B Screwed, BW and SW ¼" - 1½" FB, RB and 2" RB.

A - C Screwed, BW and SW 2" FB and 2½" RB only.

A - D Flanged ASME (ANSI) 300.

A - E Flanged EN 1092 PN40.

A - E Flanged ASME (ANSI) 150.

Note 1: On the 2" FB and 2½" RB a PTFE gasket is fitted between the body and cap.

Note 2: The flange standard may restrict the maximum operating pressure. Please check with Spirax Sarco.

Note 3: In gases applications, the maximum operating pressure is restricted to 40 bar g.

Body design conditions PN100

PMA Maximum allowable pressure 100 bar g @ 60 °C

TMA Maximum allowable temperature 260 °C @ 0 bar g

Minimum allowable temperature -29 °C

PMO Maximum operating pressure for saturated steam service 17.5 bar g

TMO Maximum operating temperature 260 °C @ 0 bar g

Minimum operating temperature

-29 °C
Note: For lower operating temperatures consult Spirax Sarco

PMX Maximum differential pressure is limited to the PMO

Designed for a maximum cold hydraulic test pressure of: 150 bar g

Page 2 of 7 TI-P133-06
CMGT Issue 20
M10S Ball Valve DN¼" to DN2½"
Materials
Please note:
Screwed, butt weld and socket weld M10V ball valves have bolts and nuts.
Flanged M10V ball valves have studs and nuts.

4 10 7

9
8
6

5
3

1 2

No. Part Material

M10S2 Zinc plated carbon steel ASTM A105

1 Body M10S3
Stainless steel ASTM A 182 F 316L
M10S4

M10S2 Zinc plated carbon steel ASTM A105

2 Cap M10S3
Stainless steel ASTM A 182 F 316L
M10S4

3 Ball Stainless steel AISI 316

4 Stem Stainless steel AISI 316

5 Seat Carbon/graphite reinforced PTFE PDR 0.8

6 Stem seal Reinforced PTFE antistatic

M10S2
Zinc plated carbon steel SAE 1010
7 Separator M10S3

M10S4 Stainless steel AISI 316

8 Spring washers Stainless steel AISI 301

M10S2
Zinc plated carbon steel SAE 12L14
9 Nut M10S3

M10S4 Stainless steel AISI 304

10 Name-plate (DN) Stainless steel AISI 430

Materials continued on the next page

TI-P133-06 Page 3 of 7
CMGT Issue 20
M10S Ball Valve DN¼" to DN2½"
Materials (continued)
Please note:
Screwed, butt weld and socket weld M10V ball valves have bolts and nuts.
Flanged M10V ball valves have studs and nuts.

14 12 13 11

16 17

No. Part Material

M10S2
Zinc plated carbon steel SAE 12L14
11 Stem nut M10S3

M10S4 Stainless steel AISI 304

M10S2
Zinc plated carbon steel SAE 1010
12 Lever M10S3

M10S4 Stainless steel AISI 316

13 Name-plate Stainless steel AISI 430

14 Grip Vinyl

M10S2
Zinc plated carbon steel A 193 B7
15 * Bolts M10S3

M10S4 Stainless steel AISI 304

M10S2
Zinc plated carbon steel SAE 1010
16 Nuts M10S3

M10S4 Stainless steel AISI 304

M10S2
Zinc plated carbon steel Grade 5
17 Studs M10S3

M10S4 Stainless steel AISI 304

* Note: Item 15 not shown - Screwed, butt weld and socket weld versions only.

Page 4 of 7 TI-P133-06
CMGT Issue 20
M10S Ball Valve DN¼" to DN2½"
Dimensions (approximate) in mm

Reduced bore
Size A A1 A2 A3 A4 B B1 C C1 D D1 D2 D3 E

¼" 63 60 - - - 120 - 61 - 24 - - - 11

3/8" 63 63 - - - 120 - 61 - 24 - - - 11

½" 63 51 108 130 140 120 120 61 87 24 89 95 95 11

¾" 68 59 117 150 152 120 120 63 89 26 98 105 117 14

1" 86 84 127 160 165 157 157 91 91 31 108 115 124 21

1¼" 97 93 140 180 178 157 157 95 95 37 118 140 133 25

1½" 106 102 165 200 190 180 180 109 109 41 127 150 156 31

2" 124 118 178 230 216 180 180 115 115 48 152 165 165 38

2½" 152 152 191 - 241 245 - 132 132 57 - - 190 51

Full bore
Size A A1 A2 A3 A4 B B1 C C1 D D1 D2 D3 E

¼" 63 60 - - - 120 - 61 - 24 - - - 11

3/8" 63 63 - - - 120 - 61 - 24 - - - 11

½" 68 68 - 130 140 120 120 63 89 26 - 95 95 14

¾" 86 86 - 150 152 157 157 91 91 31 - 105 117 21

1" 97 97 - 160 165 157 157 95 95 37 - 115 124 25

1¼" 106 106 - 180 178 180 180 109 109 41 - 140 133 31

1½" 124 124 - 200 190 180 180 115 115 48 - 150 156 38

2" 152 152 - 230 216 245 245 132 132 57 - 165 165 51

B, B1
A: Screwed and Butt weld

A1: Socket weld

A2: Flanged ASME 150

C, A3: Flanged PN40

C1
A4: Flanged ASME 300

B: Screwed, Butt weld and Socket weld

D1,
ØE B1: Flanged ASME 150, PN40
D2,
D3 D C: Screwed, Butt weld and Socket weld

C1: Flanged ASME 150, Flanged PN40

A, A1
D: Screwed, Butt weld and Socket weld

A2, A3, A4 D1: Flanged ASME 150

D2: Flanged PN40

D3: Flanged ASME 300

TI-P133-06 Page 5 of 7
CMGT Issue 20
M10S Ball Valve DN¼" to DN2½"
Weights (approximate) in kg
Size Reduced bore Full bore

Scrd/BW/SW PN40 ASME 150 ASME 300 Scrd/BW/SW PN40 ASME 300

¼" 0.61 - - - 0.61 - -

3/8" 0.61 - - - 0.61 - -

½" 0.61 2.2 1.65 2.2 0.70 2.3 2.5

¾" 0.70 2.9 2.20 2.9 1.27 3.5 4.2

1" 1.27 3.9 3.38 4.5 1.77 4.4 5.1

1¼" 1.77 5.4 4.44 7.0 2.50 6.2 7.5

1½" 2.50 6.5 5.84 8.36 3.50 7.5 10.0

2" 3.50 8.8 8.99 11.2 6.90 12.2 13.4

2½" 6.90 - - 17.5 - - -

Kv values
Size ¼" 3/8" ½" ¾" 1" 1¼" 1½" 2" 2½"

Reduced bore 2.5 6.8 6 10 27 49 70 103 168

Full bore 2.5 6.8 17 36 58 89 153 205 -

For conversion:
C v (UK) = Kv x 0.963
C v (US) = Kv x 1.156

Operating torque (N m)
Size ¼" 3/8" ½" ¾" 1" 1¼" 1½" 2" 2½"

Reduced bore 2 2 2 3.5 13 21 30 40 45

Full bore 2 2 3.5 13 21 30 40 45 -

The indicated torque values are for valves frequently operated, that are submitted to a maximum differential pressure of 62 bar.
Valves that are subject to long static periods, may require greater break-out torque.

Page 6 of 7 TI-P133-06
CMGT Issue 20
M10S Ball Valve DN¼" to DN2½"
Safety information, installation and maintenance
For full details see the Installation and Maintenance Instructions supplied with the product.

Welding
Only the models that have connections designed for welding (SW, BW, Imperial Tube connections) should be welded. Valves with SW
or BW welding connections must be disassembled before welding onto the pipeline, the ends should be welded separately and the
valve should be reassembled when the ends are cool. Carbon steel valves with threaded (BSPT, BSP, NPT) or flanged connections
must not be welded to avoid damages to the valve and/or injury to personnel.

How to order example:

1 off Spirax Sarco ½" screwed BSP M10S2FB ball valve.

Optional extras:
- Self-venting ball.
- Extended stems 50 mm (2") and 100 mm (4") to allow full insulation.
- Lockable handle.
- Fully degreased under request (ie: Oxygen application).

Spare parts
The spare parts available are shown in solid outline. Parts drawn in a grey line are not supplied as spares.

Available spares
Seat and stem seal set 5, 6

How to order spares

Always order spares by using the description given in the column headed 'Available spares' and state the size and type of ball valve.
Example: 1 - Seat and stem seal set for a ½" M10S2FB ball valve.

6 5

5 6

TI-P133-06 Page 7 of 7
CMGT Issue 20
M10S Ball Valve DN¼" to DN2½"