Complete Guide On Plans & Calculations

MECHSOFT ENGINEERING DESIGN AND CONSULTANCY
NFPA 13
(Standard for Installation of Sprinkler System/2013)
(Chapter 23)
COMPLETE GUIDE ON
PLANS
&
CALCULATIONS
 Basics of Hydraulics
 Hydraulic Calculation- PRILIMINARY CONCEPTS
 Hydraulic Calculation –EXAMPLE CALCULATION (MANUAL+
SOFTWARE)
 Hydraulic Calculation Considerations for Storage Sprinklers
– CMDA/CMSA/ESFR Sprinklers
– In Rack Sprinklers
 Plan Review Checklists
Prepared by: Mehboob Shaikh
B. Eng. || CFPS || CFI-1 || AMIE
info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

CONTENT
SN Description of Content Page No.

1 Basics of Hydraulics 3-13
2 Hydraulic Calculations ( Preliminary Concepts) 14-23
3 Hydraulic Calculations 24-54
( Example Calculation- Manual + Using Elit Software)
4 Hydraulic Calculation Considerations for Storage Sprinklers 55-71
5 Plan Review Checklists 72-92

BASICS OF HYDRAULICS

Hydraulics Focus
PRESSURE FLOW
Caused by the weight of air, varies with altitude

Atm. Pressure
Lower at high altitudes, higher at low altitudes
• 14.7 psi at sea level
The actual reading on a gage, does not account

Guage Pressure for atmospheric pressure. (psig)
The sum of atmospheric pressure and guage

Absolute Pressure pressure. (psia)
The pressure created on the walls of pipe or

Normal Pressure tanks holding water.

The pressure associated with the flow of water
Velocity Pressure measured in the same direction as the flow.
The pressure at a given point in a conduit or

Residual Pressure appliance with a specific volume of water
flowing14.7 psi at sea level
Static/Elevation The potential energy available within a system

when no water is flowing.
Pressure
info@mitionline.com Design|Inspection|Training flowing14.7
Mehboob Shaikh
psi at sea level| +919146861270
Elevation Pressure :
2
62.4 lbs/ft 2
0.433 lbs/in
1 ft 1 ft
A cubic foot of water results in a static pressure at its base of 62.4 lbs/ft2
Converted to square inches a column of water 1-foot high exerts a
pressure of 0.433 lbs/in2

Example : 01
Pressure (psi) = 0.433 X Elevation (ft)
15 ft
5 ft
What is the pressure difference?
Example : 02
What is the pressure at the hydrant?
Pressure (psi) = 0.433 x Elevation (ft)
P  0.433 x 200 ft
P  90.93psi
P  91 psi

Calculating Velocity Pressures
Pn = Pt – Pv
Where:
Pn = normal pressure (psi)
Pt = total pressure (psi)
Pv = velocity pressure (psi)
Velocity pressure can be found as follows,
0.001123Q2
Pv  4
di
• When velocities are high in a closed system the pressure needs to
be accounted for in the calculations.
• It can reduce the flows and pressures needed in a system 5-10
percent.
• In most sprinkler systems velocities are low and their pressures
create a minor effect, therefore velocity pressures can be ignored.
• It should be used at points where large flows take a 90-degree turn
in the piping.

FLOW :
Q=AxV
Q = Flow in ft3/sec
A = Cross sectional area of pipe in ft2
V = Water velocity in ft/sec
Q is a constant for any given closed system.
Q = A1 x V 1 = A2 x V 2
A 1 x V 1 = A2 x V 2

Example : 03
If water is flowing at 5.7 ft/sec in 6-inch pipe, how fast is it flowing when
the pipe size is reduced to 3-inch?
Solution :
𝐴1 X 𝑉1
V2 =
𝐴2
2 2 2
A =  r =  (3 in) = 28.3 in
1
2 2 2
A =  r =  (1.5 in) = 7.1 in
2
(28.3in2 )(5.7ft/sec)
V2   22.7ft/sec
7.1in2
V2 = 22.7 ft/sec

Flow from an Outlet :
Q  29.83 di  Pv  CD
2
Q is the flow (gpm)

di is the diameter of opening (inches)
Pv is the measured velocity pressure (psi)
CD is the discharge coefficient of the device
Note : This is used when testing water supplies to determine the amount
of flow

Flow from a Sprinkler :
Q  k P
Where:
Q is flow (gpm)
k is k-factor determined in the sprinkler listing (gpm/psi½)
P is the pressure (psi)
• The diameter of the opening and discharge coefficient are
incorporated into the empirical determination of k-factor.

Example : 04
A sprinkler is being installed with a k-factor of 5.6. If the pressure at the

sprinkler is 20 psi, how much water will exit the sprinkler?
Solution :
Q k P
Q  5.6 20 psi
Q  25.0 gpm
Example : 05
What is the pressure for a sprinkler that has a k-factor of 17.6 and the
expected flow is 83 gpm?
Solution :
2
Q 
P 
k
2
 83 gpm 
P 
 17.6 
P  4.716  22.2 psi

2

Example : 06
What is the K-factor for an outlet that is flowing 65 gpm at 30 psi?
Solution :
Q
k
P
65 gpm
k
30 psi
65
k  11.86
5.48

Hydraulic Calculation
(PRILIMINARY CONCEPTS)

Purpose of Hydraulic Calculations
Performed to tell you,
– What pipe size will be best?

– Will the water supply provide the flow and pressure necessary to
control/suppress a fire?
Hydraulic Calcualtion Formulae :
Hazen-Williams formula
– Fire sprinkler systems
– Water-spray systems
Darcy-Weisbach formula
(The Darcy-Weisbach equation more accurately accounts for the
effects of turbulence, temperature, and viscosity )
– Anti-freeze systems
– Water mist systems
– Foam-water systems
Fanning formula

Hazen-Williams formula
4.52Q1.85
PL  1.85 4.87
C di
Where:
PL = friction loss (psi/ft)
Q = flow (gpm)
C = roughness coefficient (based on pipe material)
di = interior pipe diameter (inches)

Roughness Coefficient :

Inside Diameters (di) :

Example : 07
If a pressure gage is reading 40 psi at one end of a 32-foot section of 2-
inch schedule 40 pipe (C = 120) flowing at 110 gpm, what will a gage at
the other end read?
40 ?
2-inch schedule 40 pipe

32 ft
Solution :
4.52Q1.85 4.52(110gpm)1.85
PL  1.85 4.87 
C di (120)1.85(2.067in)4.87
PL= 0.112 psi/ft
PL = 0.112 psi/ft
Friction Loss = 0.112 psi/ft x 32 ft = 3.6 psi
Guage Pressure = 40 psi – 3.6 psi  36 psi

Equivalent Length Chart :
Adjusting Equivalent Lengths
NFPA 13 table is based on schedule 40 steel pipe for a wet system

All others need to be adjusted for:
– Change in pipe material
• C-factor other than 120
– Change in interior diameter
• Other than those for schedule 40 steel

Adjusting for C-Factor for above conditions :
– Begin with the equivalent length value from the table

– Multiply the length by the factor above for the appropriate C-factor
Adjusting for Inside Diameter :
4.87
 Actual inside diameter 
Factor   
 Schedule 40 Steel Pipe inside diameter 
– Begin with the equivalent length value from the table

– Multiply the length by the factor above calculated for the inside
diameter of the pipe being used

Example : 08
What is the equivalent pipe length of Type K copper tube which used for
a 3-inch standard turn 90-degree elbow?
Solution:
See Eq. Pipe length From table – 23.4.3.1.1
3” elbow 90 degree elbow = 7 ft.
As the type of pipe is different than steel we need to adjust for,
– Type K Copper
– Interior diameter
Adjustment for material (C-factor)
See table no 23.4.3.2.1 ,23.4.4.7.1 C factor & C factor multiplier for

Copper Pipe
Copper Pipe has C Factor of 150 with multiplier of 1.51

Adjustment for inside Diameter :
See table no A. 6.3.5,
– 3-inch copper has an inside diameter of 2.907-inch
4.87
 
4.87
Actual i.d.  2.907 
Factor       0.77
 Schedule 40 Steel Pipe i.d.   3.068 
Apply the factors:

– Equivalent pipe length from table 23.4.3.1.1 = 7 ft
– Adjustment for C-factor = 1.51
– Adjustment for diameter = 0.77
Hence,The equivalent length for a 3-inch Type K Copper standard turn

elbow is:
7 ft x 1.51 x 0.77 = 8.14 ft

Hydraulic Calculation
STEP BY STEP PROCEDURE
MANUAL + ELITE SOFTWARE

The Layout Process
1. Define the Hazard

2. Analyze the Structure
3. Analyze the Water Supply
4. Select the Type of System
5. Select the Sprinkler Type(s) and Locate Them
6. Arrange the Piping
7. Arrange Hangers and Bracing (where needed)
8. Include System Attachments
9. Hydraulic Calculations
9.1 Identify hazard category
9.2 Determine sprinkler spacing
9.3 Determine piping arrangement
9.4 Calculate amount of water needed per sprinkler
9.5 Calculate number and location of open sprinklers in
the hydraulically most demanding area
9.6 Start at most remote sprinkler and work towards the
water supply calculating flows and pressures
9.7 Compare demand with supply
10. Notes and Details for Plans
11. As-Built Drawings

Example Project : A Electronic Storage Warehouse

100 FT.
Plan view
200 FT.
Elevation view
18 FT.
200 FT.
Step:1 : Define Hazard

In accordance with NFPA 13,2013- chapter Chapter 5 & Appendix A 5.3.1
Electronic factory is classified as Ordinary Hazard Group -1 Occupancy
Step:2 : Analyzed Structure

Assuming Completed
Step:3 : Analyze water Supply

Based on the Fire Flow test Conducted on Public water mains in
accordance with NFPA 291

Step:4 : Select the Type of System

Wet Pipe System
Step:5 : Type of Sprinkler

Standard Spray Quick response upright sprinkler with K factor of 5.6
Step:6,7 & 8 : Arrangement of Piping with

attachments
Sprinkler are 10 ft. apart on the branch lines and 12.5 between branch
lines.
Piping arragment is as shown below,

10 ft. between the sprinkler
5 ft. from north wall and 6ft from North

west wall Pipe Layout
z
100 FT.
200 FT.
Mains and branches are Sch 40
pipes
12.5 ft between the branch

18 FT.
15 FT.
All branches are on a 1 ft. riser

ACV
nipple N
200 FT. Gate Valve

Step: 9 : Hydraulic Calculation
Isometric View
10 ft. Standard Quick response

Maximum Area of Operation
Branch lines 12.5 ft. Sprinkler with K-5.6
1
2
5 Area of operation have
3 1-inch been reduced in
1 ½-inch accordance with cl.
1 ¼-inch 6 11.2.3.2.3
4
1 ¼-inch 7
1 ½-inch 8
BL1
3-inch Starting Sprinkler Values :

BL2 9
• Each sprinkler covers an area of 125 ft 2
• Each sprinkler is required to deliver a density of 0.15 gpm/ft 2
3-inch • Minimum flow per sprinkler:
125 ft2 x 0.15 gpm/ft2 = 18.8 gpm
BL3
Minimum pressure for 18.8 gpm:
2
Cross main  18.8 gpm 
p   11.3psi
TOR  5.6 
3-inch
Riser
N Alarm Check valve
15 ft. Gate Valve This is going to be the

Pressure @ Sprinkler -1
FF

Select a Design approach
Using Density/Area Curve (NFPA 13, Chapter 11, Fig;11.2.3.1.1)
As per above figure,

Area of operation = 1500 Sq. Ft.
Density = 0.15 gpm/sq ft.
Check for Area Adjustment :

Quick response sprinklers (in light hazard or ordinary hazard with wet pipe
system, reduce design area based on maximum ceiling height, where it is
less than 20 ft) ----NFPA 13,2013,11.2.3.2.3 excerpt,

“Area of Operation shall be permitted to be reduced withtout revising the
density as indicated in the below figure when all of the following
conditions are satified.
1. Wet Pipe System

2. Light Hazard or Ordinary hazard Occupancy
3. 20 ft. Maximum ceiling height
4. There are no Protected ceiling pockets as allowed by 8.6.7 and 8.8.7
exceeding 32 sq. ft.
- 3x
y  55
2
 3(18)
y  55
2
 54
y  55  28%
2

Design area = 1500 Sq ft.
Applying the 28% reduction in area
100% - 28% = 72%
Therefore, 1500 Sq ft. X 0.72 = 1080 Sq. Ft.
New Area of Operation = 1080 Sq .ft.

Density remains same = 0.15 gpm/Sq.ft.
Spacing between the Sprinkler (S) = 10 ft.

Spacing between the branch (L) = 12.5 ft.
Area of Coverage = S x L
Area of Coverage = 10 x 12.5
Area of Coverage = 125 Sq. ft.
𝐷𝑒𝑠𝑖𝑔𝑛 𝐴𝑟𝑒𝑎
No. of Sprinklers in the design area =
𝐴𝑟𝑒𝑎 𝑜𝑓 𝐶𝑜𝑣𝑒𝑟𝑎𝑔𝑒
1080
No. of Sprinklers in the design area =
125
No. of Sprinklers in the design are = 9 Sprinklers

No. of Sprinkler Along the branch Line = 1.2√𝐴𝑟𝑒𝑎 𝑜𝑓 𝑜𝑝𝑒𝑟𝑎𝑡𝑖𝑜𝑛 ÷ 10
No. of Sprinkler Along the branch Line = 1.2 √1080 ÷ 10
No. of Sprinkler Along the branch Line = 3.94 Say 4 Sprinklers
Check if Area Increase is required ….?

30% for dry pipe (NFPA 13,2013-11.2.3.2.5)
30% for double interlock (NFPA 13,2013-11.2.3.2.5)
30% for Pitched Ceiling (NFPA 13,2013-11.2.3.2.4)
Starting Sprinkler Values :
• Each sprinkler covers an area of 125 ft2

• Each sprinkler is required to deliver a density of 0.15 gpm/ft2
• Minimum flow per sprinkler:
125 ft2 x 0.15 gpm/ft2 = 18.8 gpm
• Minimum pressure for 18.8 gpm:
2
 18.8 gpm 
p   11.3psi
 5.6 

Check :
 What is minimum required pressure by code ? ( 7 psi)

 What is minimum pressure required by manufacturer? (specs)
 Is minimum calculated pressure greater than minimums?
11.3 > 7 Psi or Specs ? (Yes)
Data Summary :
Water Supply Information

Static Pressure 90 psi @ 0 gpm
Residual Pressure 60 psi @ 1000 gpm
Hazard Classification OH - 1
System Type Wet
Ceiling Height 18 feet
Density/Area 0.15 gpm/ft2 / 1500 ft2
Adjusted to 0.15 gpm/ft2 / 1080 ft2
Sprinkler Type Quick Response – Standard Spray
K – Factor K =5.6
Area Per Sprinkler 125 ft2
Minimum Sprinkler Flow 18.8 gpm
Minimum Pressure 11.3 psi

Calculation Paths :
Main Path :
1 2 3 4 BL1 BL2
BL3 TOR
Auxillary Paths-1 :
5 6 7 8 BL2
Auxillary Paths-2 :
6 BL3

Branch wise Calculation :
18.8 gpm @
11.3 psi
19.95 gpm
@ 12.69 psi
84..36 gpm
@ 27.28 psi
28.33 gpm
21.3 gpm @
@ 27.71psi
14.4 psi
84.36 gpm
@ 24.38 psi

N 197.07 gpm
@ 41.41 psi

SPRINKLER HYDRAULIC CALCULATION(Manual Worksheet)
Reference : NFPA 13,2013, Chapter 23, 23.3 & 23.4

Fittings-
Node- Elev- K- Flow added
Nominal ID Quantity L- ft C Factor Total(Pt)
1 1 Factor this step(q)
and Length Remarks
(Density Notes
F-ft Pf per foot (psi)( Elev(Pe) Verificat
Node- Elev- Total Flow
Actual ID 4.52*Q^1.85*/C^1.8
2 2 (Q) ion)
T- ft 5/d^4.87) Frict( Pf)
10.00 120.000 11.300 0.15
1 17 5.6 18.800 1.00 1E
2.00 0.116 Q1 = 18.8 gpm & P1 = 11.3
2 17 18.800 1.05 12.00 1.393
10.00 120.000 12.693 0.16
2 17 5.6 19.951 1.25 1T
6.00 0.116 Q2 =19.95 gpm & P2 = 12.69
3 17 38.751 1.38 16.00 1.862
10.00 120.000 14.554 0.17
3 17 5.6 21.364 1.25 1T
6.00 0.262 Q3 =21.3 gpm & P3 = 14.54
4 17 60.115 1.38 16.00 4.195
2T 19.00 120.000 18.749 0.19
4 17 5.6 24.248 1.50
16.00 0.232 0.433 Q4 =24.248 gpm & P4 = 18.74
BL1 16 84.363 1.61 35.00 8.107
0 12.50 120.000 27.289 0.67 QBL1 =84.363 gpm & PBL1 =
BL1 16 16.15 84.363 3.00
- 0.007 0.000 27.289, balaning flow @ BL1 &
BL2 | Keq @ BL1 & BL2 =
BL2 16 84.363 3.26 12.50 0.093 84.363/(27.289)^(0.5) = 16.15
0 12.50 120.000 27.382 0.67
BL2 16 84.363 3.00
- 0.027 0.000
BL3 16 168.726 3.26 12.50 0.336
3.00 1ACV 182.80 120.000 27.718 0.23
BL3 16 5.38 28.337 Keq @ BL3 = 5.38 ( Keq =
1E 18.00 0.036 6.495
18.8/12.2^0.5)
FF 16 197.063 3.26 1GV 200.80 7.196
41.409

Pressure (psi) MECHSOFT ENGINEERING DESIGN AND CONSULTANCY
System Demand
197 gpm @ 41.40 psi
With Hose Stream

447 gpm @ 41.0 psi
Flow (gpm)
Min. Density Vertification :
The value in the hydraulic calculations should be higher than the

minimum density times area due to pressure losses in the system

ELITE SOFTWARE
CALCULATION

Step :1 - General Project Data(client,Company & building data) :
Select Hazard, NFPA 13, Ch.05

Step-2 : System data:
Adjusted area of operation
City water mains flow test result

as per NFPA 291
Step -3 : Pipe Data Nodes, Pipe Length & Dia. Along
with details of fittings
Final Node will be the inflow

node

Select Calculation Mode
Step-4 : Calculation
Smaller imbalance will take more
time and result will be more accurate
Press “Calculate” upon filling

all details
Step-5 : Solution

Report :
Print Report










Hydraulic Calculation Considerations

for Storage Sprinklers

Control Mode Density Area Sprinklers :
Follow Density Area Method for calculations of flow and number of
sprinklers.
Control Mode Specific Application/Large Drop
Sprinklers :
Cl. Reference is from NFPA 13, 2019
CMSA sprinklers do not follow the density/area method of calculation

and the discharge criteria in the storage chapters do not specify how
many sprinklers to include on the branch line.
So, how to calculate the number of sprinklers on the branch line.


Example : 9
Type of Facilty : Storage Warehouse
Type of Ceiling Sprinkler : CMSA, K 11.2
Type of Commodity : Class 1, pallatized
Type of System : Wet
No. of Sprinkler in the design Area = 15 ( from Table 14.3.1 )
Protection area per sprinker = 100 SF
Max. Spacing = 10 ft.
Dimension of rectangle parallel to branch line = 1.2 x Sq. rt ( Design Area)
Therefore,
Design area = Allowable area per sprinkler x no. of sprinkler in the design
area
Design Area = 100 x 15
Design Area = 1500 SF
Dimension of rectangle parallel to branch line = 1.2 x Sq. rt ( 1500)

Dimension of rectangle parallel to branch line = 46.4 say 50
With the spacing of 10 ft between the sprinklers, 5 sprinkles will come in

one branch line and such 3 branch lines will be considered for 15 number
of sprinklers as shown below.

Early Suppression Fast Response Sprinklers :


In Rack Sprinklers :
How Many In rack Sprinklers will open in case of fire ?
Depends on,
– Number of levels of in‐racks

– Type of sprinklers at the ceiling ( CMSA/ESFR)
A) For Commodity Class 1 to 4 & Storage Height upto 25 ft.

If Spray or CMSA Sprinklers at the ceiling
In Accordance with Cl. 16.1.6.5,
No. of In rack Type of Commodity No. of Notes

Spr Level Sprinklers
1 Class 1,2 or 3 6
1 Class 4 8
2 Class 1,2 or 3 10 5 on each level
2 Class 4 14 7 on each level

Example : 10
Type of Facilty : Storage Warehouse
Type of Commodity : Class 3
No. of Rack Sprinklers Level – 02

B) For Commodity Class 1 to 4 & Storage Height over 25 ft.

If Spray or CMSA Sprinklers at the ceiling
In Accordance with Cl. 16.1.6.5,

1 Class 1,2 or 3 6
1 Class 4 8
2 Class 1,2 or 3 10 5 on each level
2 Class 4 14 7 on each level

C) For Group A Plastics
Storage of any height (upto and over 25 ft)
In accordance, 17.1.5.6

1 Group A Plastic 8
More than 1 Group A Plastic 14 7 on each level
D) For Group A Plastics
In accordance, 18.5.3

1 Rubber Tire 12
More than 1 Rubber Tire 14 7 on each level

Min. Flow and Pressure Requirement for Rack Sprinkler :
What is the min. Operating Sprinkler at rack Sprinklers ?

For Class 1 to 4 Commodity for storage upto 25 ft. ( Cl. 16.2.1.4.4)
Depends on,
– Type of sprinklers at the ceiling ( CMSA/ESFR)
If spray sprinklers or CMSA sprinklers at the ceiling
Min. Operating Pressure = 15 psi

Hence for k = 5.6 , Q = 21.7 GPM
for k = 8.0 , Q = 31 GPM
for k = 11.2 , Q = 43.2 GPM
For Class 1 to 4 Commodity for storage Over 25 ft. ( Cl.table 16.3.1.1)

If spray sprinklers or CMSA sprinklers at the ceiling
Min. Q = 30 GPM
Hence for k = 5.6 , P = 28.7 psi
for k = 8.0 , P = 14.1 psi
for k = 11.2 , P = 7.2 psi

Group A Plastics Spray Sprinklers at Ceiling :
For storage up to 25 ft, depends on the in‐rack configuration selected

from the Figures:
– Figure 17.2.1.2.1(b) & (f): 15 psi

– Figure 17.2.1.2.1(c), (d) and (e):
• 15 psi when sprinklers are at every other flue intersection

• 15 psi for k‐8 and 30 psi for k‐5.6 when sprinklers are at every flue
For storage over 25 ft:

– 30 gpm regardless of situation
Group A Plastics ESFR Sprinklers at Ceiling
• Must use k‐8.0 or K- 11.2 quick response, ordinary temprature sprinkler

• 60 gpm (17.3.3.4.1)
• 56.3 psi
Rubber Tire Storage
• 18.5.4
– 30 psi
– 30.7 gpm for k‐5.6 sprinkler

Hydraulic Calculations Steps for In Rack Sprinklers :
Step : 01 - Calculate number and location of open sprinklers in the

hydraulically most remote area.
Step : 02 - Start at most remote sprinkler and work towards the water
supply calculating flows and pressures
Step : 03 - Adding pressure increases due to friction loss
Step : 04 - Add flows from other open sprinklers encountered on the

way
Step : 05 – Adjust the Elevation changes
Example- 11 :
Type of Facility : Storage Warehouse

Type of Rack- 5 tier double row rack
Type of In Rack Sprinkler : Rack, K 5.6
Width of Aisle : 8 ft.
Type of Commodity : Class 3,Encapsulated
No. of Rack Sprinklers Level – 02

System Layout :
OH Sprinklers Demand shall be calculated
separately and balanced at the point of connection
unless specifically asked not to do so.
1
2
B 3
4
5
6
7
8
9
10
A
10

Hydraulic Calculations Sheet- Manual
IN RACK SPRINKLER SYSTEM HYDRAULIC CALCULATION

Reference : NFPA 13- 2013, Chapter 23 ( PLANS AND CALCULATIONS)
Fittings- Quantity
Node-1 Elev-1 K- Factor Flow added this step(q) Nominal ID L- ft C Factor Total(Pt)
and Length
Notes
F-ft Pf per foot (psi) Elev(Pe)
Node-2 Elev-2 Total Flow (Q) Actual ID
T- ft 4.52*Q^1.85*/C^1.85/d^4.87 Frict( Pf)
10.00 120.000 15.000
1 20 5.6 21.700 1.25 1T
6.00 0.040 Q1 = 21.70 gpm & P1 = 15 psi
2 20 21.700 1.38 16.00 0.637
10.00 120.000 15.637
2 20 5.6 22.144 1.25 1T
6.00 0.146
3 20 43.844 1.38 16.00 2.339
10.00 120.000 17.976
3 20 5.6 23.743 1.25 1T
6.00 0.326
4 20 67.587 1.38 16.00 5.210
10.00 120.000 23.186
4 20 5.6 26.965 2.00 1T
10.00 0.084
5 20 94.552 2.07 20.00 1.682
10.00 120.000 24.868
5 20 5.6 27.926 2.50 1T
12.00 0.057 Flow at Node B
B 20 122.478 2.47 22.00 1.263
10.00 120.000 15.000
6 10 5.6 21.689 1.25 1T
6.00 0.040
7 10 21.689 1.38 16.00 0.636
10.00 120.000 15.000
7 10 5.6 21.689 1.25 1T
6.00 0.143
8 10 43.377 1.38 16.00 2.294
10.00 120.000 17.294
8 10 5.6 23.288 1.25 1T
6.00 0.317
9 10 66.665 1.38 16.00 5.079
10.00 120.000 22.372
9 10 5.6 26.488 1.25 1T
6.00 0.589
10 10 93.153 1.38 16.00 9.431
10.00 120.000 31.804
10 10 5.6 31.581 2.00 1T
10.00 0.140
Flow at Node B
A 10 124.734 2.07 20.00 2.809
10.00 120.000 34.612
A 10 0 0.000 2.50 1T
12.00 0.211 -4.330
B 20 247.213 2.47 22.00 4.633 Total Flow at Node A+ Node B
150.00 120.000 34.915
B 20 0 0.000 2.50 1T, 3E, 1CV
31.00 0.211 2.165
C 15 247.213 2.47 181.00 38.113 Total Flow at C
75.193

Calculation for Over Head Sprinklers :
In accordance with table 16.2.1.3.2
– Figure 16.2.1.3.2(f); Curve “C”

– 0.345 gpm per sq ft over 2000 sq ft

In accordance with Cl. 16.2.1.3.4.4
Reduce by 20% due to extra level of in‐rack sprinklers (see 16.2.1.3.4.4)

Here, required level of in rack sprinklers are ONE however, in actual we
have TWO
Hence, Final density will become, 0.276 GPM @ 2000 SF

After calculation, Let’s say, ceiling sprinkler demand at Point “C” is:
– 665 gpm at 84 psi

Lets Put Demands Together
 Ceiling
– 665 GPM @ 84 PSI
 In Rack
– 247 at 75 PSI
• Can’t add flows unless the pressure is the same

• Adjusting the lower pressure situation to the higher pressure is
called “Balancing the Flows

Steps to Balance the Flows :
– Calculate the two demands separately from the most remote point
to the node where they connect
– Get the k‐factor for the lower pressure situation
– Apply the k‐factor to the higher pressure to get the new flow:
– Add the two flows together
Step 01 :
– Calculate the two demands separately from the most remote point
to the node where they connect
a. In‐Racks: 247 gpm at 75 psi

b. Ceiling: 665 gpm at 84 psi
Step 02 :
– Get the k‐factor for the lower pressure situation
In Racks are the lower situation in this case,
𝑄
K=
𝑆𝑞.𝑟𝑡 𝑃
247
K=
𝑆𝑞.𝑟𝑡 75
K = 28.52

Step 03 :
Apply the K‐factor to the higher pressure,
Q = K X Sq. rt (P)
Q = 28.52 x Sq. rt. ( 84)
Q = 261.4 GPM
Step 04:
Add the flows together
– In‐Racks: 262 gpm at 84 psi
– Ceiling: 665 gpm at 84 psi To In Ceiling Level Sprinklers
To In Rack Sprinklers
In Racks : 247 @ 75 Psi

Ceiling : 665 @ 84 Psi
Balanced Demand: 927 GPM @ 84 Psi
Therefore, Total Combined demand = 927 GPM @ 84 psi

PLAN REVIEW CHECKLISTS

PROJECT WORKFLOW DOCUMENTS

SPRINKLER SYSTEM PLAN REVIEW CHECKLIST
STEP 1: GENERAL PROJECT INFORMATION
Permit no.: _____________________ Project/occupancy name: __________________
Project address:
______________________________________________________________________
Owner’s name:
______________________________________________________________________
Sprinkler contractor name:

______________________________________________________________________
Contractor address:
______________________________________________________________________
Point of contact (name):

______________________________________________________________________
Contractor phone: __________________________________ e-mai _______________
Date of review by AHJ: _______________________
Date comments sent to contractor:____________________
Name of AHJ plans examiner:
______________________________________________________________________

• Code and edition governed by project: ______________________________________
•Edition of NFPA 13 used for design: ________________________________________
• Type of system being installed: Wet___ Dry ___ Preaction ___ Deluge_____________
• Is this a new system or a change to an existing system? _ New system _ Change to

existing system
• Owner certificate included: Yes____ No _____
•Building description:
Square footage of the project: ________________________
Use of building: __________________________ Building height: __________________
Total area of building: _____________________ Area per floor: ___________________
Total number for floors above grade: __________ below grade: ___________________
What is the construction type?

– Fire resistive
– Noncombustible
– Ordinary
– Heavy timber
– Wood frame
– Mixed
• What is the fire sprinkler occupancy hazard classification?

– Light hazard _
– Ordinary hazard Group I
– Ordinary hazard Group II
– Extra hazard Group I
– Extra hazard Group II
– Storage
– Special occupancy

•Are there special occupancy requirements for the system?
_ Yes _ No
(Flammable/combustible liquids, aircraft hangars, oxidizers, etc.)
• Is there storage over 12 ft (3.7 m)? _ Yes _ No

• If this is a storage occupancy, what is the commodity classification?
– Class I
– Class II
– Class III
– Class IV
– Group A
– Group B
– Group C
STEP 2: GENERAL PLANS INFORMATION
The following has been shown on plans correctly:
YES NO
– __ Name of owner or occupant
– __ Location, including street address
– __ Point of compass
– __ Full height cross section
– __ Ceiling/roof heights and slopes not shown in the full height cross section
– __ Location of partitions
– __ Location of fire walls
– __ Occupancy class of each area or room
– __ Location and size of concealed spaces, closets, attics, and bathrooms
– __ Small enclosures in which no sprinklers are to be installed
– __ Scale the plans were drawn to
STEP 3: WATER SUPPLY
The following water supply information is clearly indicated on plans:
_____Capacity is verified at _______ gpm (L/min) for a duration of ______ hours for a
total capacity of ______ gal (L)

Type of water supply:
_____ Public _____Stored water (tanks) ____Raw water source
YES NO
_ _ Location and elevation of static and residual hydrants in relationship to the riser
location
_ _ Date and time of flow test (must be within one year of design)
_ _ Static, residual, and flow from test
_ _ Name of person who conducted or source of water supply information
Private Fire Service Mains
The following information is clearly indicated on plans:
– Size, length, and location of main

– Material listed for use
– Point of connection to city main
– Size, type, and location of valves
– Size, type, and location of valve indicators
– Size, type, and location of regulators
– Size, type, and location of meters
– Size, type, and location of valve pits
Depth of top of pipe laid below grade
– Size and location of all thrust blocks
– Size and location of hydrants (showing size and number of outlets and whether
outlets to be equipped with independent gate valves)
– Whether hose houses and equipment are to be provided and by whom
Fire Pump
– Electric
– Diesel
– Steam
– N/A
Rated Capacity: ____________________
_ The pump layout complies with NFPA 20.
Water Tank
– Steel
– Wood
– Concrete

– Fiberglass
– NA
Water tanks comply with the requirements of NFPA 22.
STEP 4: SPRINKLER SYSTEM TYPE AND COVERAGE
• Type of sprinkler system
– Wet
– Dry
– Preaction
– Deluge
• Classification of occupancy:
– Light hazard
– Ordinary: Group 1 _ Group 2 _
– Extra hazard: Group 1 _ Group 2 _
• Classification of commodity: (Chapter 4)
– Class I
– Group A plastic
– Class II
– Group B plastic
– Class III
– Group C plastic
– Class IV
– Mixed commodity
Plastic pallet storage?
Reinforced _
Unreinforced _
• Are sprinklers omitted in any areas? _ Yes _ No

• If yes, are omissions allowed per NFPA 13? _ Yes _ No _ N/A
• What is the area of coverage?

– Total
– Partial
– Special hazard
– Other
All wet piping is in areas that can be maintained above 4°C (40°F)

STEP 5: SPRINKLER SYSTEM COMPONENTS
The following sprinkler component information is clearly indicated on plans specifications:
– Product data is included in the shop drawing submittal

– Make, type, model, nominal K-factor of sprinklers, and sprinkler identification
number
– Temperature rating and location of high-temperature sprinklers]
– Pipe type and schedule of wall thickness
– Nominal pipe size and cutting lengths of pipe (or center-to-center dimensions)
– Location and size of riser nipples
– Type of fittings and joints and location of all welds and bends
– Specifications of any sections to be shop welded and type of fittings or formations
to be used
– Type and location of hangers, sleeves, braces, and methods of securing sprinklers
when applicable
– All control valves and check valves
– Make, type, model, and size of wet pipe, dry pipe, preaction, or deluge valves
– Size and location of standpipe risers, hose outlets, hand hose, monitor nozzles,
and related equipment
– Calculation of loads for sizing and details of sway bracing
– Setting for pressure-reducing valves
– Manufacturer, size, type of backflow preventers
– Type and amount of antifreeze solution used
– A pressure gauge on the system and the supply
STEP 6: DESIGN
The following design information is clearly indicated on plans or specifications:
– Total area protected by each system on each floor

– Number of sprinklers on each riser per floor
– Sprinkler spacing and location verified
– Spray patterns free of obstruction
– Total number of sprinklers on each dry pipe, preaction, combined dry pipe-
preaction, or deluge system
– Approximate capacity [in gal (L)] of each dry pipe system
– Pitch of pipe for dry pipe, preaction, combined dry pipe-preaction, or deluge system
– Size and capacity for air compressor (where provided) for dry pipe, preaction,
combined dry pipe-preaction, or deluge system
– Details of air supply connections for other types of air supply
– Piping provisions for flushing
– Size, location, and arrangement of all auxiliary drain connections.

– Where equipment is to be installed as an addition to an existing system, enough
detail of the existing system indicated to
– make all conditions clear
– Hydraulic data nameplate (for hydraulically designed systems)
– Size, location, thread type, and piping arrangement of fire department connections
– Size, location, and arrangement of inspector’s test connection.
– Location of main drain connection
STEP 7: HYDRAULIC DESIGN SPECIFICATIONS
The following information has been clearly indicated on plans / specifications / hydraulic
calculations:
– Type of system:
– Hydraulically calculated
– Pipe schedule
– Proper hydraulic calculations forms used?
– Design area and water application rate:

– Density/area method
– Special design areas
– Room design method
– Special design approaches
– Density/area method
– Area of operation and density noted?
– Area of operation reduced for:
– Quick-response sprinklers
– High-temperature sprinklers
– Area of operation increased for: Sloped ceilings
– Dry pipe/double-interlock preaction systems _
– Multiple adjustments needed?
– Area per sprinkler

– Water supply sufficient?
– Allowance for in-rack sprinklers provided (where required)
– Limitations (dimension, flow, and pressure) for listed special sprinklers specified
– Most demanding area calculated
– Hydraulic reference points shown on the plan that correspond with comparable
reference points on the hydraulic calculation sheets
– Pipe sizes and lengths shown on the plan correspond with the sizes and lengths
shown on the hydraulic calculations sheets
– Total quantity of water and pressure required noted at a common reference point
for each system

– Relative elevations of sprinklers, junction points, and supply or reference points
– All unprotected wall openings throughout the floor protected for room design
method where permitted
– Pressure loss for backflow preventer, meter or other devices included in hydraulic
calculations.
STEP 8: ALARMS
The following alarm connections are clearly indicated on plans/specifications:
– Type and location of alarm bells

– Fire alarm system connection
– Type and location of waterflow switch / pressure switch
– Type and location of low air pressure switch
– Type and location of all tamper switches.

PLAN REVIEW CHECKLISTS
GENERAL SHOP DRAWINGS/ WORKING PLANS
Description Yes No NA
Name of owner and occupant.
Location, including street address.

Point of compass.
Full-height cross section, or schematic diagram, including
structural member information if required for clarity and including
ceiling construction and method of protection for metallic piping
Location of partitions.
Location of fire walls.
Occupancy class of each area or room.
Location and size of concealed spaces, closets, attics, and

bathrooms.
Any small enclosures in which no sprinklers are to be installed.
Size of city main in street and whether dead end or circulating if

dead end, direction and distance the nearest circulating main; and
city main test results and system elevation relative to test hydrant.
Other sources of water supply, with pressure or elevation.
Make, type, model, and nominal K-factor of sprinklers.
Temperature rating and location of high-temperature sprinklers.

Total area protected by each system on each floor.
Number of sprinklers on each riser per floor.
Total number of sprinklers on each dry-pipe system, preaction

system, combined dry- pipe preaction system, or deluge system.
Approximate capacity in gallons of each dry-pipe system.
Pipe type and schedule of wall thickness.
Nominal pipe size and cutting lengths of pipe (or center-to-center

dimensions). Where typical branch lines prevail, it shall be
necessary to size only one typical line.
Location and size of riser nipples.

Type of fitting, joints and location of all welds and bends. The
contractor shall specify on drawing any sections to be shop
welded, the type of fitting or formations to be used.
Type and locations of hangers, sleeves, braces, and methods of
securing sprinklers when applicable.
All control valves, check valves, drain pipes, and test connections.
Make, type, model, and size of alarm or dry-pipe valve
Make, type, model, and size of preaction or deluge valve.

Kind and location of alarm bells
Size and location of standpipe risers, hose outlets, hand hose,
monitor nozzles, and related equipment.
Private fire service main sizes, lengths, locations, weights,
materials, point of connection to city main; the sizes, types, and
locations of valves, valve indicators. regulators, meters, and valve
pits; and the depth that the top of the pipe is laid below grade.
Piping provisions for flushing
Where the equipment is to be installed as an addition to an existing

system, enough of the existing system indicated on the plans to
make all conditions clear.
For hydraulically designed systems, the information on the
hydraulic data nameplate
A graphic representation of the scale used on all plans
Name and address of contractor
Hydraulic reference points shown on the plan that correspond with

comparable reference points on the hydraulic calculation sheets
The minimum rate of water application (density), the design area
of water application, in-rack sprinkler demand, and the water
required for hose streams both inside and outside
The total quantity of water and the pressure required noted at a
common reference point for each system
Relative elevations of sprinklers, junction points, and supply or
reference points
If room design method is used, all unprotected wall openings
throughout the floor protected
Calculation of loads for sizing and details of sway bracing
The setting for pressure-reducing valves.
Information about backflow preventors (manufacturer, size, type).

Information about antifreeze solution used (type and amount).

Size and location of hydrants, showing size and number of outlets
and if outlets are to be equipped with independent gate valves.
Whether hose houses and equipment are to be provided, and by
whom, shall be indicated. Static and residual hydrants that were
used in flow tests shall be shown.
Size, location, and piping arrangement of fire department
connections.
Manufacturer’s installation instructions for any specially listed
equipment, including descriptions, applications, and limitations for
any sprinklers, devices, piping, or fittings.
Water supply capacity information.
a. Location and elevation of static and residual test gauge with
relation to the riser reference point.
b. Flow location
c. Static pressure, psi (bar).
d. Residual pressure, psi (bar).
e. Flow, gpm (1/min).
f. Date.
g. Time.
h. Test conducted by or information supplied by.
i. Other sources of water supply, with pressure or elevation.
INDIVIDUAL PLANS
Plot or Site Plan
Areas sprinkled clearly outlined or structure noted as totally

sprinkled.
North Arrow present and indicating correct direction (plan and/or
true-north).
Location(s) of city mains indicated as well as size and type of pipe.
Elevation of finished floor indicated.
Vicinity map indicating neighboring streets.

Public and private fire hydrants indicated. Static and residual
hydrants noted.
Flow test data on drawing indicating. Static, Residual, Flow, Date,
Time, Witnesses
Drawing scale clearly indicated per NFPA requirements
Actual street address for project given, not cross streets

Details of fire hydrants, taps, valves, pits clearly indicated and
appropriate for city
Bill of materials list provided.
Plans prepared by or checked and stamped by a licensed
professional engineer as required by the Fire Department/Civil
Defense or project architect/engineer
Fire Sprinkler Plan General Items and Information

Typical general notes and disclaimers on drawings.

Pipe types and schedules consistent with the specifications and
estimate guideline.
Pipe types and schedules consistent with hydraulic calculations.
Materials submitted foreign or domestic per specification and
estimate guideline.
Trapeze hangers detailed, locations clearly indicated, and all parts
listed.
Typical drop and/or sprig lengths indicated and quantities shown.
System Type (wet, dry, pre-action. etc.) clearly indicated.

Boundaries between systems and system types clearly indicated
Final plot is readable. No cluttered text and piping is clearly distinct

from architectural background items.
Job name and number is in title block.
Scale indicated and graphic on drawing.
Cross section shown and building type and construction indicated.
Riser or connection detail shown.

Ceiling heights and room numbers shown.

Fire Sprinkler Head Types. Spacing, and Location

No sprinklers farther than one half the maximum allowable spacing

Clear spray around columns, over walls and partitions as well as
under ducts, soffits or other obstructions
No heads less than 6 feet apart or per listing (ESFR, Large Droplet).
Spacing between lines not over 12' or 12'-6" for 25' bays in
warehouses or storage areas classified as High Piled.
Deflector distances from deck or obstructions per code and/or
sprinkler listing. Distances to joists or beams measured to close
edge not centerline
Head spacing does not exceed code and/or manufacturer listing
Areas of sprinkler coverage per code and/or manufacturer listing
Spacing and orifice sizes (K factors) match hydraulic calculations.
Sufficient heads included in remote area (check flow and area of

coverage).
Branch Lines and Riser Nipples

Typical lines noted and/or numbered as typical
Lines clearly indicated as to system by number and color code

Sizes, fittings, lengths, pipe types and schedules match hydraulic
calculations.
All hangers cut.
Hanger spacing and location per code, specification, listing

requirements
Appropriate hangers and fasteners for structure used.
Pipe lengths beyond last hanger meet code
Changes in elevation up, down, or sloped indicated
Joining method (threaded, grooved, press fit) clearly indicated.

Correct size, type, and location of welded outlets listed
Branch line locations dimensioned to structure not to architectural

walls
Center line to Top of Sprinkler and FF (finished floor) clearly
indicated
Pipe lengths noted on drawing are final actual cut lengths.
All riser nipples have size, length, and direction (up or down)
indicated
Riser nipple sizes and lengths match hydraulic calculations
Hydraulic nodes at top and bottom of riser nipples
Riser nipples numbered, listed with lines, and/or noted as typical
Mains
All main piping tagged, numbered and matches stock list.

Main piping size and schedule matches hydraulic calculations.
All main piping cut, appropriate takeouts used.
Welded outlet dimensions add up to main length.
Mains dimensioned to structural walls and/or columns.
Main elevation noted centerline to Top of Sprinkler and/or finished

floor.
Main hangers spaced per code and specification.
Where trapeze hangers are used, standard hangers used at
intermediate structural beams or trusses.
Typical pieces noted and listed as typical.
Pipe end treatments indicated (G/G, T/G, T/T, etc.).
Size and location of reducing couplings indicated.
Main piping color coded where helpful or necessary.

Seismic bracing provided and properly located where required by
code.
Correct size, type, and location of welded outlets, fittings, or
flanges listed.

Riser and Connection Details

Type of control valve indicated (OS&Y, butterfly, etc.).

Alarm valve, if used, noted including indication with or without
retard chamber and/or water motor gong.
All riser pipes sized and cut lengths noted
Additional check valves and type indicated (wafer, swing, grooved,
etc.).
Outlet provided (or tee) for Fire Department Connection
Flow switch indicated, including type
Tamper switch indicated, if required. Type appropriate for control

valve. Indication if electronically monitored. Signs required as
necessary for ceiling areas.
Additional pipe and fittings included for main drain, bell line and
bell drain.
Fire Department Connection, if on riser, shown
Fire Department Connection

Size of FDC indicated and per code, both inlets and outlets.
Number of inlets sufficient to satisfy code. (approx. 250 gpm per

2½ inlet).
The type of fire department threads noted
Finish noted (brass, polished, etc.)

Wall plate included with appropriate lettering (and finish).
Break caps or matching plugs with chains provided (with correct
finish).
FDC located at correct and/or acceptable height above grade. Not
less than 36 inches from grade.

Minimum of 4 feet of pipe from check to inside of wall in areas
subject to freezing.
Check valve below main control and FDC if dry system
QUICK REFERENCE SHEET FOR REVIEWING SPRINKLER PLANS

(Also known as “Twenty Questions”)
QN Description Yes NO NA
1 Is the information sufficient to review plans?

2 Is the hazard and/or commodity classification proper for the
occupancy?
3 Is the protection area per sprinkler within requirements for the
appropriate hazard classification?
4 Are distances between the branch lines and between sprinklers
on the branch lines within the maximum allowable? Are end
sprinklers and end branch lines within the allowable distance
from the walls?
5 Are sprinklers positioned within allowable deflector distances
to ceilings? Are the clearances to obstructions proper?
6 Are sprinklers to proper temperature rating for maximum
expected ceiling temperatures and proximity to unit heaters,
skylights, etc.?
7 Has an inspector’s test connection been provided at the end of
each sprinkler system?
8 Has a fire department connection been provided and properly
located?
9 Are sufficient pipe hangers properly located?
10 Are a sufficient number of systems provided to meet the
maximum system size requirements?
11 If a dry system, does the total system volume require a quick-
opening device? Does the total system volume fall within
specified limits or will a 60 second water delivery time need to
be proven?
12 Is a system drain of adequate size provided?
13 Does the water supply data appear reasonably recent? Do the
plans indicate when and where the last flow test was made and
who performed it?
14 If a hydraulically designed system, do the design density and
area meet the proper curve?
15 If hydraulically designed does the system demand point fall
below the supply curve on the Flow Test Summary Sheet?

16 Are the pipe joining techniques and C-factor proper for the type
of pipe and system?
17 Does the K-factor of the sprinklers shown on the drawings
match that used in the hydraulic calculation?
18 Does the choice of hydraulically most remote area appear
proper?
19 Are all sprinklers, valves, pumps, hangers, cut and roll grooved
couplings and plain-end fittings listed for fire protection
service? Does piping meet acceptable materials specifications?
20 Is complete sprinkler protection provided?
END OF DOCUMENT

Complete Guide On Plans & Calculations

Uploaded by

Copyright:

Available Formats

Complete Guide On Plans & Calculations

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Complete Guide On Plans & Calculations

Uploaded by

Copyright:

Available Formats

MECHSOFT ENGINEERING DESIGN AND CONSULTANCY

Prepared by: Mehboob Shaikh

B. Eng. || CFPS || CFI-1 || AMIE

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

SN Description of Content Page No.

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

Caused by the weight of air, varies with altitude

• 14.7 psi at sea level

The actual reading on a gage, does not account

• 14.7 psi at sea level

The sum of atmospheric pressure and guage

• 14.7 psi at sea level

The pressure created on the walls of pipe or

• 14.7 psi at sea level

• 14.7 psi at sea level

The pressure at a given point in a conduit or

Static/Elevation The potential energy available within a system

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

What is the pressure difference?

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

Q is the flow (gpm)

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

A sprinkler is being installed with a k-factor of 5.6. If the pressure at the

P  4.716  22.2 psi

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

Performed to tell you,

– What pipe size will be best?

Hydraulic Calcualtion Formulae :

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

2-inch schedule 40 pipe

PL= 0.112 psi/ft

Guage Pressure = 40 psi – 3.6 psi  36 psi

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

Adjusting Equivalent Lengths

NFPA 13 table is based on schedule 40 steel pipe for a wet system

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

– Begin with the equivalent length value from the table

Adjusting for Inside Diameter :

– Begin with the equivalent length value from the table

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

See Eq. Pipe length From table – 23.4.3.1.1

3” elbow 90 degree elbow = 7 ft.

As the type of pipe is different than steel we need to adjust for,

Adjustment for material (C-factor)

See table no 23.4.3.2.1 ,23.4.4.7.1 C factor & C factor multiplier for

info@mitionline.com Design|Inspection|Training Mehboob Shaikh | +919146861270

See table no A. 6.3.5,

– 3-inch copper has an inside diameter of 2.907-inch

Apply the factors: