C H1 H6 Manual Jan.2021

Reading time: 8min
Full Race Unit installation manual part № “C-H1” “C-H6”
Please read carefully before attempting any use of this product!
To install the SP-Full Race Unit you will have to:
1. Gain access to the ignition coils (for best results refer to your motorcycle service manual). Plug in
the female connectors to the ignition coils and the male connectors to the bike's harness. You must
connect each male and female connector pair to the same corresponding cylinder no matter left to
right or right to left!
IMPORTANT NOTE: Make sure when plugging the connectors that you press them well enough to lock,
as this will provide sealed and reliable electrical connection, vital for the function of the Full Race Unit.
Find appropriate place for the Full Race Unit control box and route the cables, they are high quality,
automotive class cables but there is some care you should take: Avoid moving parts as they might
damage them, the best way is to follow other cables from the bike's harnes, use cable ties to fasten
them. Make sure the place for the Full Race Unit control box is away from heavy vibrations, heat and it
is not constantly exposed to rain and water.
NOTE: The Full Race Unit connects direcly to the ignition coils, if you use another product(s) for altering
or modifying the ignition coil signals (that needs to be connected to the ignition coils as well) you need
to connect the Full Race Unit control box first in line to the ignition coils.
2. Connect the Full Race speed sensor wiring (pink wire) to the vehicle speed sensor. Depending on
make and model you may be supplied with direct plug and play connectors or Posi-Tab terminal for
connection to the speed sensor signal output.
Posi-Tap connector installation guide:
1. Do not strip run wire.

2. Unscrew the big end cap counter-clockwise
3. Insert the run wire in the big end cap slot.
4. Screw the big end cap to pierce and provide signal.
3. The Full Race Unit will require negative (ground) connection to power up, connect the single
black wire to the battery NEGATIVE (-) lead.
4. Remove your original tie rod and install SP-Shift Sensor with the fitting rod(s) provided to its
place. Route the wire to the Full Race Unit control box and plug it in. When installing the sensor, make
sure all counter nuts are locked and the sensor wire is not under tension when pressing the gear lever all
the way up and down. The rod and sensor provided are made with DUAL THREADS (left and right hand
at the same time) which makes fitting universal.
NOTE: The gearbox pivot arm must extend to 90 degrees with the shift rod in order to receive equal
force in both directions, if not set corectly, the gearbox may not react accordingly and miss gears when
using the quickshifter!
After this is done, turn the ignition key ON, make sure the engine kill switch is in RUN position and the
gearbox is in neutral, at this time the Full Race control box must power up and enter normal operation
displaying SP flashing.
Perform vehicle speed signal test before using or setting anything!
Speed signal test: Lift the rear wheel on a paddock stand, with everything connected power up the
control box by turning the ignition key on (engine kill switch must be in RUN position, engine must not
be running). Now rotate the rear wheel by hand, the control box display must flicker the lights to
indicate it can read the vehicle speed signal.
BEFORE USING THE QUICKSHIFTER YOU MUST ENSURE THE CORRECT SENSOR MOTION FOR YOUR
SHIFT SETUP IS SELECTED, PLEASE REFER TO THE FOLLOWING TABLE - OPTION SS
Full Race Unit C-type control box setup video link
The following is a menu table for adjusting the control box parameters.
To enter setup mode:
Press and hold LB and RB together then power the control box to initiate count down timer for
entering the setup mode, hold down the buttons for 3 seconds.
The following is shift sensor calibration procedure.
(Required only if you’re replacing an existing sensor!)
Activating sequence for the Launch Control:

- The vehicle speed must be 0km (rear wheel standing still).
- The engine RPM must drop at idle for at least 1,5seconds.
- The engine RPM must raise to the pre-set Launch Control RPM limit (twist the throttle here).
What is the (Ultra Smooth) shift feature:
This option will restore the power on the next gear when using the quickshifter by firing
sequential cylinders allowing smooth transition between gears, particularly suitable for cruise
and city riding.
What is the (Ar) launch control option:
This option defines the active range of the launch control RPM limit, for example if the launch
control is set to 7000RPM this option will define how many combustion cycles are allowed when
the limit is reached and therefore allowing smaller or greater limit to which the engine RPM are
held by the launch control.
What is the (SC) shift sensor sensitivity control:
This option allows you to adjust the force required by the shift sensor to initiate a shift
depending on engine RPM. You can adjust 3 levels of force (A = Low, b = Med, c = High)
depending on 5 RPM ranges respectively: 1 = (3k to 5k); 2 = (5k to 7k); 3 = (7k to 9k); 4 = (9k to
11k); 5 = (11k to red line). This option has been pre-set from factory we recommend to test ride
before changing the parameters.
Force reset of the control box
With everything connected turn the ignition key on with the engine kill switch in RUN position,
the engine must not be running then press and hold the shift lever in the direction of upshifting
all the way in – at this point the control box will display a counter starting from 1 hold the shift
lever until 9 is reached, module is now reset to the factory pre-set values, refer to the above
table.
NOTE: The Full Race Unit arrives from the manufacturer with the Launch Control deactivated,
you have to set the Launch Control RPM limit to make it active.
Tips on adjusting your Quickshifter!

The Full Race Unit arrives with best overall setting to your motorcycle make and model. We
strongly recommend you to test ride it before changing the St settings. Use the following as a
general guide when adjusting your Quickshifter:
If when using the Quickshifter the gearbox seems to push back the shift lever, the shift feels
rough and you have experienced missed gears - this means that the gearbox needs more time to
react – increase the St shift time.
If when using the Quickshfiter the motorcycle front dives for too long and the shift seems slow -
this means that you have to lower the shift time – decrease the St shift time. Best results for
most motorcycles are achieved with the following time settings - (60ms-70ms).
The Quickshifter has a threshold RPM which means that the engine speed must exceed the
minimum threshold in order to activate the Quickshifter function. The factory setting are over
3000RPM and this is not adjustable.
If for some reason you're experiencing difficulties adjusting your Shift Power product, you think
it is not functioning as expected or you would like to share your opinion please feel free to
contact us to support you with a professional help.
Web: https://www.shiftpower.co.uk Email: info@ShiftPower.co.uk
This product is covered by one year warranty against malfunctions from the original date of
purchase under the following conditions – link click here.
Warranty disclaimer:
Shift Power Ltd shall not under any circumstances, be liable for any special, incidental or
consequential damaged including, person, party or property, but not limited to, damage loss of
cost of purchased or replacement goods or service, claims of customers of the purchaser, which
may arise and/or result from sale or use of these parts. Installation of these parts could
adversely affect the engine manufacturer warranty coverage.
Thank you for purchasing the Full Race Unit!

C H1 H6 Manual Jan.2021

Uploaded by

Copyright:

Available Formats

C H1 H6 Manual Jan.2021

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

C H1 H6 Manual Jan.2021

Uploaded by

Copyright:

Available Formats

Reading time: 8min

Full Race Unit installation manual part № “C-H1” “C-H6”

Please read carefully before attempting any use of this product!

To install the SP-Full Race Unit you will have to:

Posi-Tap connector installation guide:

1. Do not strip run wire.

Perform vehicle speed signal test before using or setting anything!

To enter setup mode:

Activating sequence for the Launch Control:

Tips on adjusting your Quickshifter!

Web: https://www.shiftpower.co.uk Email: info@ShiftPower.co.uk

You might also like