BK PRECISION 251x - Manual

Model: 2511, 2512, 2515, 2516
2510 Series Handheld Digital

Storage Oscilloscopes
USER MANUAL
Safety Summary
The following safety precautions apply to both operating and maintenance
personnel and must be observed during all phases of operation, service,
and repair of this instrument. Before applying power, follow the
installation instructions and become familiar with the operating
instructions for this instrument.
If this device is damaged or something is missing, contact the place of
purchase immediately.
This manual contains information and warnings that must be followed to

ensure safe operation as well as maintain the meter in a safe condition.
DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE
Do not operate the instrument in the presence of flammable gases or
fumes. Operation of any electrical instrument in such an environment
constitutes a definite safety hazard.
KEEP AWAY FROM LIVE CIRCUITS
Instrument covers must not be removed by operating personnel.
Component replacement and internal adjustments must be made by
qualified maintenance personnel. Disconnect the power cord before
removing the instrument covers and replacing components. Under certain
conditions, even with the power cable removed, dangerous voltages may
exist. To avoid injuries, always disconnect power and discharge circuits
before touching them.
DO NOT SUBSTITUTE PARTS OR MODIFY THE INSTRUMENT
Do not install substitute parts or perform any unauthorized modifications
to this instrument. Return the instrument to B&K Precision for service and
repair to ensure that safety features are maintained.
WARNINGS AND CAUTIONS
WARNING and CAUTION statements, such as the following examples,
denote a hazard and appear throughout this manual. Follow all
instructions contained in these statements.
A WARNING statement calls attention to an operating procedure, practice,
or condition, which, if not followed correctly, could result in injury or death
to personnel.
2
A CAUTION statement calls attention to an operating procedure, practice,
or condition, which, if not followed correctly, could result in damage to or
destruction of part or all of the product.
NOTE:
Voltage ratings are given as “working voltage”. They
should be read as Vac-rms (50 – 60 Hz) for AC sine
wave applications and as Vdc for DC applications.
WARNING
 Do not connect the scope probes and DMM leads simultaneously.

 Before using the DMM functions, disconnect all scope probes. Likewise,
disconnect all DMM test leads before using any scope functions.
 When not in use, remove all scope probes, DMM test leads, and the USB
cable.
WARNING
To avoid potential fire or shock hazard:
 Disconnect all probes, leads, power adapter, and USB cable before
opening the battery cover.
 Do not turn on the instrument while the battery cover is removed.
 Use only the included insulated probes, test leads, and power adapter
supplied with the instrument.
 Use only the battery pack supplied with the instrument or approved by
us. Do not use other substitutes.
 For AC power operation, always connect the adapter to the outlet first
before connecting to the instrument.
 Observe all markings and ratings on the instrument before connecting
to the instrument.
 While making measurements, verify that the performance ratings of
instruments and accessories that are used meet the correct safety levels
of the instrument.
3
 Do not insert metal objects into any of the connectors.
WARNING
 Do not use any exposed metal BNC or banana plug connectors with the
instrument. Use only the insulated accessories supplied with the
instrument.
 Do not connect the USB cable while the instrument is not in use. Keep
the cable away from all probes and test leads.
 Always connect the probes or test leads to the instrument first before
connecting to any other device under test (DUT). To remove,
disconnect them from the DUT first before disconnecting from the
instrument.
 Do not operate the instrument in wet environments.
 For high voltage testing, keep the BNC connectors and the entire
instrument dry.
 Do not apply input voltages above the instrument and the probe’s
voltage rating.
CAUTION
 Always cover the DC power input and USB ports on the side of the
instrument with the rubber lid when not in used.
 Do not use any abrasive chemicals or volatile liquid when cleaning the
instrument. If using a cloth dampened with water, allow the instrument
to completely dry before reconnecting it.
4
Compliance Statements
Disposal of Old Electrical & Electronic Equipment (Applicable in the
European Union and other European countries with separate collection
systems)
This product is subject to Directive

2002/96/EC of the European Parliament and
the Council of the European Union on waste
electrical and electronic equipment (WEEE) ,
and in jurisdictions adopting that Directive,
is marked as being put on the market after
August 13, 2005, and should not be
disposed of as unsorted municipal waste.
Please utilize your local WEEE collection
facilities in the disposition of this product
and otherwise observe all applicable
requirements.
5
CE Declaration of Conformity
The power supply meets the requirements of 2006/95/EC Low Voltage
Directive and 2004/108/EC Electromagnetic Compatibility Directive with the
following standards.
Low Voltage Directive

- EN 61010-1: 2010
Safety requirements for electrical equipment for
measurement, control, and laboratory use-Part 1: General
requirements
- EN 61010-031: 2002+A1: 2008
Part 31: Safety requirements for hand-held probe
assemblies for electrical measurement and test
EMC Directive
- EN 61326-1: 2006
- EN 61000-3-2: 2006+A2: 2009
- EN 61000-3-3: 2008
6
Safety Symbols
Electrical Shock hazard.
Refer to the operating user manual for warning information to

avoid hazard or personal injury and prevent damage to
instrument.
This symbol shows that the switch is a power switch located at

the front panel. Pressing this button turns on the oscilloscope,
and holding it down for a few seconds turns off the
oscilloscope.
CATI Category I overvoltage conditions.

Measurement instruments whose measurement inputs are
not intended to be connected to the mains supply. The
voltages in the environment are typically derived from a
limited-energy transformer or a battery.
CATII Category II overvoltage conditions.
meant to be connected to the mains supply at a standard wall
outlet or similar sources.
CATIII Category III overvoltage conditions.
meant to be connected to the mains installation of a building.
Maximum Input Voltages
Oscilloscope Inputs
 Maximum input voltage to CH1 and CH2 BNC direct(1:1) - CATII 300V
RMS, CATI 150V RMS
 Maximum input voltage to CH1 and CH2 BNC via 10:1 probe PR250SA
(included with models 2515 and 2516) - CATII 1000V RMS, CATIII 600V
RMS
7
 Maximum input voltage to CH1 and CH2 BNC via 1X/10X probe PR150SA
(included with models 2511 and 2512) – CATII 300V RMS
 Scope Input – CATII 300V RMS
 Meter Input – CATII 600V RMS, CATIII 300V RMS
NOTE:
Maximum Floating Voltage
These apply to models 2515 and 2516 only, which have channel isolation
that allows for floating measurements.
 Maximum floating voltage from input CH1 and CH2 to earth ground
– CATII 1000V RMS, CATIII 600V RMS
 Maximum floating voltage between CH1 and CH2 reference – CATII
1000V RMS, CATIII 600V RMS
The following applies to all models:
 Maximum floating voltage from multimeter reference to earth

ground – CATII 600V RMS, CATIII 300V RMS
NOTE:
8
Environmental Conditions
The instrument may be operated in the following environment.
Operating Environment 0 °C to 40 °C
Storage Humidity 0 – 85% R.H.
Storage Environment -20 °C to +70 °C
Pollution degree Pollution degree 2
Measurement Category CAT II, CAT III
9
Table of Contents
Safety Summary .............................................................................................. 2
1 General Information ............................................................................. 16
1.1 Product Overview ........................................................................... 16
1.2 Package Contents ........................................................................... 17
1.3 Front Panel Overview ..................................................................... 18
Front Panel Description ........................................................................ 18
1.4 Top View ......................................................................................... 20
1.5 Rear Panel Overview ...................................................................... 20
1.6 Side Panel Overview ....................................................................... 21
Side Panel Description .......................................................................... 21
1.7 Display Overview ............................................................................ 22
Oscilloscope Display .............................................................................. 22
Digital Multimeter Display .................................................................... 24
Recorder/Trend Plot Display ................................................................. 25
1.8 Protection Fuse .............................................................................. 26
1.9 Isolation (Model 2515/2516) ......................................................... 26
1.10 Probes ......................................................................................... 27
2 Getting Started...................................................................................... 28
2.1 Input Power Requirements ............................................................ 28
External Power Operation .................................................................... 28
Battery Operation ................................................................................. 29
2.2 Tilt Stand......................................................................................... 30
2.3 Power On Device ............................................................................ 30
2.4 Perform Self-Calibration................................................................. 31
2.5 Set to Factory Default .................................................................... 32
2.6 Configure Date and Time ............................................................... 35
2.7 Probe Compensation ...................................................................... 36
3 Using the Oscilloscope .......................................................................... 39
10
3.1 Channel Selection ........................................................................... 39
3.2 Channel Menu ................................................................................ 40
Channel Coupling .................................................................................. 41
Bandwidth Limit .................................................................................... 41
Vertical Scale ......................................................................................... 41
Probe Attenuation Scale ....................................................................... 41
Invert Waveform ................................................................................... 42
Digital Filter ........................................................................................... 42
3.3 Automatic Settings and Run/Stop Mode ....................................... 43
Auto Setting .......................................................................................... 43
Run/Stop Mode ..................................................................................... 44
3.4 Scope Menu.................................................................................... 44
Acquire Menu ....................................................................................... 44
Display Menu ........................................................................................ 45
Math Menu ........................................................................................... 49
Horizontal System ................................................................................. 54
Vertical System ..................................................................................... 60
Reference Waveform Menu ................................................................. 62
3.5 Trigger System ................................................................................ 64
Adjust Trigger Level............................................................................... 64
Edge Trigger .......................................................................................... 65
Pulse Trigger.......................................................................................... 67
Video Trigger ......................................................................................... 69
Slope Trigger ......................................................................................... 72
Alternative Trigger ................................................................................ 74
3.6 Connecting External Memory ........................................................ 75
3.7 Save/Recall Function ...................................................................... 76
Saving and Recalling Setups and Waveforms ....................................... 78
Saving Screen Capture .......................................................................... 83
Saving Waveform Data ......................................................................... 83
11
3.8 Utility Menu.................................................................................... 84
Check System Information .................................................................... 86
Enable/Disable Key Sound .................................................................... 87
Enable/Disable Frequency Counter ...................................................... 87
Set the Language ................................................................................... 88
Updating Firmware ............................................................................... 88
Set Screen Saver.................................................................................... 90
Waveform Record Function .................................................................. 90
Playback Recorded Waveform .............................................................. 93
3.9 Measurement and Cursor Functions.............................................. 94
Measurement Functions ....................................................................... 94
Cursor Functions ................................................................................. 101
4 Using the Digital Multimeter .............................................................. 108
4.1 DC and AC Voltage Measurements .............................................. 109
DC Voltage Measurement ................................................................... 110
AC Voltage Measurements ................................................................. 112
4.2 DC and AC Current Measurements .............................................. 113
DC Current Measurements ................................................................. 114
Make AC Current Measurements ....................................................... 116
4.3 Make Resistance Measurements ................................................. 118
4.4 Make Diode Measurements ......................................................... 120
4.5 Continuity Test ............................................................................. 121
4.6 Make Capacitance Measurements............................................... 123
4.7 Using Trend Plot ........................................................................... 124
5 Using the Recorder ............................................................................. 125
Scope Trend Plot ..................................................................................... 125
Record Data with Trend Plot............................................................... 127
Save Recorded Data to External Memory........................................... 129
Scope Recorder ....................................................................................... 130
Configure Record Options................................................................... 133
12
Start Scope Recording ......................................................................... 133
Playback Scope Recording .................................................................. 134
Meter Trend Plot..................................................................................... 136
Record Data with Trend Plot............................................................... 139
Save Recorded Data to External Memory........................................... 140
6 Remote Communication ..................................................................... 142
7 Troubleshooting Guide ....................................................................... 143
System Message Prompts and Instructions ............................................ 143
Frequency Asked Questions.................................................................... 144
Oscilloscope ........................................................................................ 144
Multimeter .......................................................................................... 145
8 Specifications ...................................................................................... 146
Oscilloscope Specifications ..................................................................... 146
Maximum Input Voltages........................................................................ 150
Multimeter Specifications ....................................................................... 152
Recorder Specifications .......................................................................... 154
General Specifications ............................................................................ 155
11 Maintenance ....................................................................................... 156
Cleaning................................................................................................... 156
SERVICE INFORMATION .............................................................................. 157
LIMITED THREE-YEAR WARRANTY .............................................................. 158
13
List of Figures
Figure 1 - Front Panel View ........................................................................... 18

Figure 2 - Top View ....................................................................................... 20
Figure 3 - Rear View ...................................................................................... 20
Figure 4 - Side View....................................................................................... 21
Figure 5 - Oscilloscope Display...................................................................... 22
Figure 6 - Multimeter Display ....................................................................... 24
Figure 7 – Scope Trend Plot Display.............................................................. 25
Figure 8 - Connecting Power Adapter ........................................................... 28
Figure 9 - Installing Battery ........................................................................... 29
Figure 10 - Boot Screen ................................................................................. 31
Figure 11 - Utility Menu 4/4.......................................................................... 35
Figure 12 - Date/Time Menu......................................................................... 35
Figure 13 - Date and Time Display ................................................................ 36
Figure 14 - Channel Display........................................................................... 39
Figure 15 - Auto Setting ................................................................................ 43
Figure 16 - XY Mode ...................................................................................... 47
Figure 17 - Inverted Screen Color ................................................................. 48
Figure 18 - Grid and Axes Display ................................................................. 48
Figure 19 - Axes Only Display ........................................................................ 49
Figure 20 - No Grid and Axes Display ............................................................ 49
Figure 21 - Math Waveform Display ............................................................. 51
Figure 22 - FFT Full Screen (left), Split Screen (right) ................................... 53
Figure 23 - Horizontal Position Reference Marker ....................................... 55
Figure 24 - Horizontal Scale Indicator ........................................................... 55
Figure 25 - Horizontal Position Indicator ...................................................... 56
Figure 26 - Horizon Menu ............................................................................. 56
Figure 27 - Delay Scan ................................................................................... 57
Figure 28 - Normal Memory Depth............................................................... 58
Figure 29 - Long Memory Depth ................................................................... 58
Figure 30 - Vertical Position Markers............................................................ 60
Figure 31 - Vertical Position Indicator .......................................................... 61
Figure 32 - Fine Control Volts/Div ................................................................. 62
Figure 33 - Reference Waveforms Display.................................................... 63
Figure 34 - Trigger Level Display ................................................................... 64
Figure 35 - Hold Off Time Indicator .............................................................. 67
Figure 36 - Pulse Width Trigger Condition Display ....................................... 69
Figure 37 - USB Drive Detected..................................................................... 76
14
Figure 38 - USB Drive Removed .................................................................... 76
Figure 39 - Directory Menu 1/2 .................................................................... 79
Figure 40 - Create Directory Name ............................................................... 80
Figure 41 - Save Progress .............................................................................. 81
Figure 42 - Save Successfully......................................................................... 81
Figure 43 - Overwrite Warning ..................................................................... 82
Figure 44 - Subdirectory View ....................................................................... 83
Figure 45 - System Information Display ........................................................ 87
Figure 46 - Frequency Counter Display ......................................................... 88
Figure 47 - Record Frame Indicator .............................................................. 92
Figure 48 - Recording Finished...................................................................... 92
Figure 49 - All Voltage Measurements Display ............................................. 99
Figure 50 - All Time Measurements Display ............................................... 100
Figure 51 - All Delay Measurements Display .............................................. 100
Figure 52 - All Measurements Display ........................................................ 100
Figure 53 - Manual Voltage Cursor ............................................................. 102
Figure 54 - Manual Time Cursor ................................................................. 103
Figure 55 - Track Cursor Display ................................................................. 105
Figure 56 - Auto Cursor Measuring Vpp ..................................................... 106
Figure 57 - Auto Cursor Measuring Period ................................................. 107
Figure 58 - Multimeter Display ................................................................... 108
Figure 59 - Out of Range ............................................................................. 111
Figure 60 - Connection for DC Voltage Measurement ............................... 111
Figure 61 - Connection for AC Voltage Measurement................................ 113
Figure 62 - Connection for Low DC Current Measurement ........................ 115
Figure 63 - Connection for Higher DC Current Measurement .................... 115
Figure 64 - Connection for Low AC Current Measurement ........................ 116
Figure 65 - Connection for Higher AC Current Measurement .................... 117
Figure 66 - Connection for Resistance Measurement ................................ 119
Figure 67 - Connection for Diode Measurement ........................................ 121
Figure 68 - Continuity Test .......................................................................... 121
Figure 69 - Connection for Continuity Test ................................................. 122
Figure 70 - Capacitance Measurement ....................................................... 123
Figure 71 - Connection for Capacitance Measurement .............................. 124
Figure 72 - Scope Recorder External Save Mode ........................................ 133
Figure 73 - Recording Display ..................................................................... 134
Figure 74 - Playback Scope Recording ........................................................ 135
Figure 75 - Meter Trend Plot Display .......................................................... 137
15
1 General Information
1.1 Product Overview

The B&K Precision 2510 series handheld digital storage oscilloscope
combines the functions of a digital storage oscilloscope, digital multimeter,
and a recorder into one portable form factor. The oscilloscope’s bandwidth
is up to 100 MHz with a real time sampling rate of up to 1 GSa/s. With up to
2M points of deep memory, it allows for capturing more details of a signal
for analysis. Additionally, the multimeter provides most of the standard
measurement functions, which include AC and DC voltage, AC and DC
current, resistance, capacitance, diode, and continuity. The recorder
function allows users to quickly capture data without the need to connect
to a computer.
Features:
 5.7” color TFT LCD Display
 Oscilloscope, multimeter, and recorder functionality (trend plot and
waveform recorder)
 Fully isolated oscilloscope channels (models 2515 and 2516 only)
and isolated multimeter inputs
 6000-count multimeter
 Multimeter supports voltage, current, resistance, capacitance,
diode, and continuity measurements
 Supports scope and multimeter measurement parameters trend plot
and scope waveform recorder
 32 auto measurement functions
 Store/recall 2 groups of reference waveforms, 20 groups of common
waveforms, 10 groups of instrument settings
 USB interface for remote communication
16
1.2 Package Contents
Please inspect the instrument mechanically and electrically upon receiving
it. Unpack all items from the shipping carton, and check for any obvious
signs of physical damage that may have occurred during transportation.
Report any damage to the shipping agent immediately. Save the original
packing carton for possible future reshipment. Every oscilloscope is shipped
with the following contents:
 1 x 2510 series handheld digital storage oscilloscope

 1 x 7.4 V Li-Ion battery (inside battery compartment)
 1 x User Manual
 2 x 10X CATIII 600 V probes (models 2515 and 2516 only)
 2 x 1X/10X CATII 300 V probes (models 2511 and 2512 only)
 1 x Pair of DMM test leads
 1 x Carrying case and straps (models 2515 and 2516 only)
 1 x USB cable
 1 x Probe compensation connector
 1 x AC power adapter
 1 x Certificate of Calibration
 1 x Test Report
Verify that all items above are included in the shipping container. If
anything is missing, please contact B&K Precision.
17
1.3 Front Panel Overview
2 26
25
3
4 24
23
5
22
6 21
7 20
19
8 18
9 17
10 16
11 12 13 14 15
Figure 1 - Front Panel View
Front Panel Description

1 LCD display
2
- Menu function keys
3 Scope function button
4 Multimeter function button
5
Recorder function button
Trend plot and waveform recorder
6 Channel 1 button (scope)
18
7 Trigger Menu button
8 Channel 1 Volts/div range keys (scope)
9 Power On/Off
10 Channel 1 vertical position keys (scope)
11 10 A current input port (multimeter)

12 mA current input port (multimeter)
13 User/Options Menu
14 COM input port (multimeter)
15
Voltage/Resistance/Capacitance input port
(multimeter)
16 Channel 2 vertical position keys (scope)
17 Horizontal position keys (scope)
18 Channel 2 Volts/div range keys (scope)
19 Horizontal Timebase keys (scope)

20 Channel 2 button (scope)
21 Save/Recall Menu button
22 Cursor/Measurement function button (scope)
Run/Stop button; also acts as a Single button
23
when trigger mode is set to Single (scope)
24 Arrow selection keys
25 Auto button (scope)
19
26 Menu On/Off button
1.4 Top View
Channel 1 Input Channel 2 Input
Figure 2 - Top View
1.5 Rear Panel Overview
Battery cover
Kickstand
Figure 3 - Rear View
20
1.6 Side Panel Overview
2 4
Figure 4 - Side View
Side Panel Description

1
MiniUSB device port
For probe compensation and remote interface
USB host port
2 For saving/recalling waveforms and instrument
setups
3 External power adapter input
4 Mount holes for carry handle
21
1.7 Display Overview
Oscilloscope Display
1 2 3 4 5
6
16 7
15 8
9
14 10
11
13 12
Figure 5 - Oscilloscope Display
Trigger status
 Armed – Instrument is acquiring pre-trigger data. All triggers
are ignored.
 Ready – All pre-trigger data has been acquired and the
instrument is ready to accept a trigger
1
 Trig’d – Instrument has triggered and is acquiring post-trigger
data
 Stop – Instrument has stopped acquiring waveform data
 Auto – Instrument is in auto mode and is acquiring
waveforms without trigger
 Scan – Instrument is acquiring and displaying waveform data
continuously. This mode is automatically set for when
22
timebase is slow enough in which requires a longer time to
“scan” to acquire the entire signal on display
2
Displays the position of the present waveform window in internal
memory
3 Horizontal trigger position marker
USB mode indicator
 Side USB interface is configured for PC
4
communication
 Side USB interface is configured for printer (not available)
Battery indicator
5
 - Battery charging
 - Battery empty
 - Battery full
6 Time and date display
7 Trigger position marker
8 Horizontal trigger position
9 Trigger signal frequency
10 Trigger voltage indicator
11 Menu header/label
12 Horizontal timebase
13 Menu display
Signal coupling
 - DC coupling
 - AC coupling
14
 - GND(ground) coupling
Volts/div indicator
Bandwidth limit On/Off indicator
 B - Bandwidth limit ON
15 Channel 2 identifier
16 Channel 1 identifier
23
Digital Multimeter Display
1 2 3 4
5
6
Figure 6 - Multimeter Display
Input port indicator

1 Highlights which port to connect to for selected measurement
function
2 Relative value display
3 Measurement type
4 AC power indicator
5 Operation mode
6 Measurement reading display
7 Measurement bar graph
24
Recorder/Trend Plot Display
1 2 3 4
5
6
Figure 7 – Scope Trend Plot Display
1 Recording/Trend Plot time

2 Parameter A measured value
3 Parameter B measured value
4 Battery indicator
5 Parameter A measured data plot
6 Parameter B measured data plot
7 Current measured value and time
25
1.8 Protection Fuse
There are two input protection fuses for the current measurement inputs,
labeled mA and 10 A.
The 10 A input is protected with an internal 10 A, 250 V slow blow glass

tube type fuse.
The mA input is protected with an internal 600 mA PPTC (resettable) type

fuse, rated 250 V.
1.9 Isolation (Model 2515/2516)

Models 2515 and 2516 have fully isolated channel inputs, which allow for
making floating measurements safely and accurately in various applications
that may not have reference to earth ground.
Oscilloscope Probe Input BNC

(PR250SA) CATII 300V (all
models)
CATII 1000V
CATIII 150V
CATIII 600V
Input Signal Input Signal
Float Voltage Float Voltage
CATII 1000V CATII 1000V

CATIII 600V CATIII 600V
26
1.10 Probes
WARNING:
Only use the supplied oscilloscope probes or probes
recommended by B&K Precision. Using probes not
recommended and/or supplied by B&K Precision may
cause a safety hazard, and may also damage the
instrument and void its warranty.
Models 2515 and 2516 come with two touch-protected passive 10X test
probes (PR250SA) with the following specifications:
Voltage Rating: 1000 V CATII, 600V CATIII

Attenuation: 10X
Bandwidth: 250 MHz
Meets IEC 61010-031:2008
Models 2511 and 2512 come with two passive 1X/10X probes (PR150SA)
with the following specifications:
Voltage Rating: 300 V CATII

Attenuation: 1X/ 10X
Bandwidth: 17/150 MHz
Meets IEC61010-31
27
2 Getting Started
2.1 Input Power Requirements

The handheld oscilloscope can be powered by an AC adapter or by battery.
External Power Operation
To use the external AC adapter to power the instrument:
1. Connect the adapter to the external power input on the side of the
instrument first.
2. Then, connect the supplied power cord to the adapter.
3. Connect AC adapter to an electrical outlet.
Figure 8 - Connecting Power Adapter
Adapter specifications:
Input: AC 100-240V, 50/60Hz, 1.2 A
Output: DC 9V, 4 A
Center pin positive, 5.5mm tip
28
WARNING:
Only use the supplied external AC adapter. Using a
different or incorrect type adapter will result in
damage to the instrument and void its warranty.
Battery Operation
The instrument can be powered by an external Li-ion battery pack, rated for
5000 mAh, 7.4 V. The battery must be installed and charged before first
time use for battery operation.
Installing the Battery
1. Use a screw driver to remove the two screws securing the battery
cover in the rear panel.
2. Connect the 2-pin connector of the battery to the 2-pin input
connector on the lower left corner of the battery compartment.
3. Place the battery pack inside the compartment and place the battery
cover. Fasten the two screws to tighten.
Battery
Battery
1 2 3
Figure 9 - Installing Battery
29
Charging the Battery
For first time use, fully charge the battery for at least 4 hours with the
instrument turned OFF.
Before charging the battery, follow the instructions above to install the
battery. Then, connect the AC adapter to the instrument. While the
instrument is ON, the battery indicator will show the battery status for
charging and when it’s fully charged (see “1.7 Display Overview”). The
battery also charges when the instrument is OFF.
2.2 Tilt Stand

The instrument has a tilt stand on the back that can be folded out for
benchtop use. Simply pull it out from the back so that the weight of the
instrument rests on the stand.
2.3 Power On Device
Power ON the device by pressing once.
30
The oscilloscope will display a boot screen shown below for 5-10 seconds
before the main operating display appears.
Figure 10 - Boot Screen
To power OFF the device, hold down for at least 3 seconds.
2.4 Perform Self-Calibration

We recommend you to perform self-calibration if any of the following
applies:
- Operating temperature changes by more than 5 °C after
30 minutes of use.
- Abnormal behaviors and operations are present.
- Measurements are out of accuracy.
CAUTION:
Before performing self-calibration, disconnect all
inputs of the instrument. Otherwise, the instrument
may not calibrate correctly or may cause errors.
31
To perform self-calibration, follow these steps:
1. Power ON the instrument and allow it to warm up for 30

minutes.
2. Press and press to select Do Self Cal.
3. Follow the prompt on the screen and press F4 to proceed. To
exit and cancel self-calibration, press F5.
4. The following screen will display. Wait for the progress bar to
show 100% complete. When self-calibration is finished, the
screen will prompt you to exit.
2.5 Set to Factory Default
To set the instrument to factory default settings, press and toggle

to select Type and Factory. A Load option will appear. Press the
corresponding key to load factory default settings.
Table 1 - Factory Default Settings
32
Menu or
Options, Knobs or Buttons Default setup
system
Coupling DC
BW Limit Off
Volts/div Coarse
CH1, CH2
Probe 1X
Invert Off
Filter Off
Volts/div 1.00V
Operation CH1+CH2
CH1 Invert Off
CH2 Invert Off
FFT Operation:
MATH Source CH1
Window Hanning
FFT Zoom 1X
Scale dBVrms
Display Split
Window Main Time Base
Position 0.00 μs
Sec/div 500 μs
HORIZONTAL
Window Zone 50.0 μs
Trigger knob Level
Type Off
Source CH1
CURSOR
Horizontal (voltage) +/-3.2 divs
Vertical (time) +/-5 divs
Three Mode Options Sampling
ACQUIRE Averages 16
Sampling Method Real Time
Type Vectors
DISPLAY Persist off
Grid
33
Intensity 60%
Brightness 40%
Format YT
Menu Display Infinite
Type Setups
SAVE/RECALL Save To Device
Setup No.1
Source CH1
REF REFA Off
REFB Off
Sound On
Frequency Counter On
UTILITY
USB Device Computer
Record Off
Type Edge
Source CH1
Slope Rising
TRIGGER (Edge)
Mode Auto
Coupling DC
Level 0.00V
Type Pulse
Source CH1
Condition =
TRIGGER (Pulse)
Set Pulse Width 1.00ms
Mode Auto
Coupling DC
Type Video
Source CH1
TRIGGER Polarity Normal
(Video) Sync All Lines
Standard NTSC
Mode Auto
Type Slope
TRIGGER Source CH1
(Slope) Condition
Time 1.00ms
34
Mode Auto
Type Alternative
Source CH1
TRIGGER
Mode Edge
(Alternative)
Coupling DC
Slope Rise
2.6 Configure Date and Time

Users can configure the date and time on the oscilloscope.
Press and press three times to go to the Utility menu 4.
Figure 11 - Utility Menu 4/4
Press to select Date/Time.
Figure 12 - Date/Time Menu
To configure:
Year Press and use and keys to change the

year.
Press so that the Month is highlighted. Use

Month
and keys to change the month.
Day Press so that the Day is highlighted. Use and
35
keys to change the day.
Press so that the Hour is highlighted. Use and

Hour
keys to change the hour.
Press so that the Minute is highlighted. Use

Minute
and keys to change the hour.
Once set, press to select Confirm option and save changes.
To enable or disable the date and time display, toggle in the menu
to change Display to On or Off. Date and time will be displayed in the
upper right corner, as illustrated below.
Figure 13 - Date and Time Display
2.7 Probe Compensation
When you connect the probe to an arbitrary channel for the first time,
please make the following adjustment to make the probe match with the
channels. Probes without compensation or compensation warp may lead to
36
imprecise or false measurements. You can perform the adjustments
manually to match your probe with the input channels.
1. Set the probe attenuation option in the channel 1 menu to 10X by
pressing and press F4 to select Probe until it shows 10X.
2. Connect the BNC side of the probe to channel 1 input on the top of the
instrument.
3. Attach the probe compensation connector to the miniUSB port on the

side of the instrument.
Probe compensation connector
37
4. Connect the probe tip to the 3V port (1 kHz, 3Vpp Square Wave) and
the reference ground clip to the ground port on the probe
compensation connector.
5. Display the channel and press .

6. Check the shape of the waveform displaying on the screen.
Under Compensated Correctly Compensated Over Compensated
7. Adjust the trim on the probe or repeat all the operations above if
necessary.
38
PR250SA
PR150SA
3 Using the Oscilloscope
3.1 Channel Selection
Use the and/or button to enable or disable channel 1 and/or

channel 2 on the display. These buttons will also access their respective
channel menus.
Figure 14 - Channel Display
39
3.2 Channel Menu
To access the channel menu, press or to display the respective

channel menu. Below is a table of the channel menu structure.
Table 2 - Channel Menu 1/2
Menu
Setting Description
Option
DC passes both AC and DC
DC
components of the input signals.
AC blocks the DC component of the
Coupling
AC input signals and attenuates signals
below 10 Hz.
GND GND disconnects the input signal.
Limit the bandwidth above 20 MHz to
On reduce display noise; filters the signals
BW Limit
Off to reduce noise and other unwanted
high frequency components.
Change the range of voltage by 1-2-5
Coarse
sequence.
V/div
Fine control of the volt/div scale
Fine
settings.
Set to match the type of probe
1X, 5X, 10X, 50X,
Probe 100X, 500X, 1000X
attenuation you are using to ensure
correct vertical scale display.
Enter the second page of CH1/CH2
Next Page Page1/2
menu.
40
Table 3 - Channel Menu 2/2
Menu
Setting Description
Option
On
Invert Enable/Disable waveform invert function.
Off
Filter Enter the FILTER menu.
Set waveform vertical position and trigger level to
To Zero
zero.
Next
Page 2/2 Return to the first page of CH1/CH2 menu.
Page
Channel Coupling
Both channel 1 and channel 2 coupling can be set to DC, AC, or GND
(ground). Press in the channel menu to toggle the settings.
Bandwidth Limit
Bandwidth limit can be enabled or disabled by toggling in the

channel menu. When enabled, there will be a B indicator next to the
channel indicator below the bottom left corner of the oscilloscope
waveform display area.
Vertical Scale
The vertical scale control adjustment can be set for coarse or fine control.
Press the button in the channel menu to toggle between Coarse
and Fine.
Probe Attenuation Scale
The voltage/division display scale can be changed to match the attenuation

factor on the oscilloscope probe. To change this, press the button
41
in the channel menu to select and change the Probe setting. As you change
this setting, the volt/div scale indicator will also change based on the
attenuation factor selected.
Invert Waveform
The oscilloscope can display the inverted signal of the input waveform on
channel 1 and channel 2. To enable this, press from the channel
menu to go to the second menu page, and press to toggle Invert
between On and Off.
Digital Filter
There are four types of digital filters available and can be used to apply to
the input waveform. To access the digital filter menu, go to page two of the
channel menu and press to enter the filter menu. Below is a table
of the filter menu structure.
Table 4 - Digital Filter Menu
Option Setting Description

On Turn on the digital filter.
Digital Filter
Off Turn off the digital filter.
Setup as LPF (Low Pass Filter).
Setup as HPF (High Pass Filter).
Type
Setup as BPF (Band Pass Filter).
Setup as BRF (Band Reject Filter).
Use the up and down arrow keys to set
Upp_Limit
upper limit.
Use the up and down arrow keys to set
Low_Limit
lower limit.
Return Return to the CH1 or CH2 menu.
42
3.3 Automatic Settings and Run/Stop Mode
Auto Setting
When measuring an unknown signal, the auto setting function can be used
to allow the oscilloscope to automatically adjust the vertical and horizontal
scale, range, and trigger to display the signal.
To use this function, input a channel to either or both channel 1 and 2.

Then press the button. Within a few seconds, the oscilloscope will
adjust and display the waveform to fit inside the display window. At this
point, press the button to select how the waveform should be
displayed.
Figure 15 - Auto Setting
Press to select the waveform showing multiple cycles.

Press to show a single cycle of the waveform if frequency is
detected.
Press to show the waveform triggered on its rising edge.
Press to show the waveform triggered on its falling edge.
Press to undo the automatic setting and revert back to the previous
settings.
43
Run/Stop Mode
Press the button to toggle between continuous run mode and

stopped mode.
In continuous run mode, the signal going into channel 1 and/or 2 will
constantly be triggered regardless of the position of the trigger level. At the
top, the indicator will display “Trig’d” to indicate that the signal is triggered.
In stopped mode, the oscilloscope will stop triggering the signals going into
channel 1 and/or 2. At this point, users can zoom or pan to view the entire
waveform acquired from the last trigger.
3.4 Scope Menu
To access the scope menu, press the orange colored key. There are
five submenus: Acquire, Display, Math, Horizon, and Ref.
Acquire Menu
To access the acquire menu, go to the scope menu and press to

select Acquire. Below is a table of the Acquire menu structure.
Table 5 - Acquire Menu
Menu
Setting Description
Option
44
Sampling Sample and display most waveforms accurately.
Acquisition Peak Detect Detect burr and reduce fake wave phenomena.
Average Reduce random and irrelative noise.

4, 16, 32, Select the number of samples for average
Averages
64,128,256 acquisition.
sinx Use sine interpolation
Sinx/x
x Use linear interpolation
Equ time Set the sampling mode to equivalent sampling.
Mode
Real time Set the sampling mode to real time sampling.
Sa Rate Display the sampling rate.
To change the settings to any of the menu options, press their

corresponding function keys ( - ).
Sampling: To construct the waveform, the scope samples the signals in

equal interval.
Peak Detect: The scope captures the maximum and minimum values of the
signals in every interval to display the waveform.
Average: The scope acquires several waveforms, averages them, and
displays the final waveform. The more average times the smoother the
waveform.
Equivalent Time Sampling: This mode is good for observing repetitive
periodic waveforms. The sampling rate is up to 50 GSa/s.
Real Time Sampling: The scope will use the highest real-time sampling rate
up to the specified maximum sampling rate.
Note: Sampling rate varies based on the selected horizontal timebase

setting.
Display Menu
To access the display menu, go to the scope menu and press to

select Display. Below is a table of the Display menu structure.
45
Table 6 - Display Menu 1/2
Menu Option Setting Description

Vectors fill the space between
Vectors adjacent sample points on the
Type
display.
Dots Dots display the sample points only.
Off
1 sec
Set the length of time each displayed
Persist 2 sec
sample point remains displayed.
5 sec
Infinite
Intensity 0 – 100% Set waveform intensity.
Brightness 0 – 100% Set grid brightness.
Enter the second page of DISPLAY
Next Page Page 1/2
menu.
Table 7 - Display Menu 2/2
Menu
Setting Description
Option
YT format displays the vertical voltage in
YT
relation to time (horizontal scale).
Format XY format displays a dot each time a
XY sample is acquired on channel 1 and
channel 2.
Normal Set to normal mode.
Screen
Inverted Set to invert color display mode.
Display grids and axes on the screen.
Grid Turn off the grids.
Turn off the grids and axes.
46
Menu 2sec, 5sec, 10sec,
Set display time of menu on the screen.
Display 20sec, Infinite
Next Page Page 2/2 Return to the first page of DISPLAY menu.
To change the settings to any of the menu options, press their

corresponding function keys ( - ).
Persistence: The wavefrom persistence can be configured by changing the

Persist menu option of the Display menu page 1. Use the to
toggle between persistence timing.
Intensity and Brightness: The waveform intensity and the display grid
brightness can be adjusted by first pressing for intensity or
for grid brightness in the Display menu page 1. Then, use the or
arrow keys to increase or decrease the intensity or brightness

percentage respectively.
YT format: YT is the default format that displays the waveform of voltage
vs. time.
XY format: XY is the format that display the waveform as channel 1 (X) vs.
channel 2 (Y). When this format is used, the horizontal scale and position
keys cannot be used.
Below is an example of using XY mode with two sine waves for channel 1
and 2 with 90 degree offset.
Figure 16 - XY Mode
47
Screen Invert: The colors of the screen can be inverted. Toggle the
button in the Display menu 2 to switch between normal and
inverted display. Below is an illustration of the inverted screen.
Figure 17 - Inverted Screen Color
Grid Display: The display of the grid can be changed to show grid and axes,
axes only, or no grid or axes. The below screenshots illustrate the options.
This can be changed by toggling in the Display menu 2.
Figure 18 - Grid and Axes Display
48
Figure 19 - Axes Only Display
Figure 20 - No Grid and Axes Display
Math Menu
To access the math menu, go to the scope menu and press to

select Math. Below is a table of the Math menu structure.
Note: Math function is not available in XY mode.
49
Table 8 - Math Menu 1/2

＋ CH1+CH2
－ CH1-CH2, CH2-CH1
Operation * CH1*CH2
/ CH1/CH2, CH2/CH1
FFT Fast Fourier Transform.
On Invert the waveform.
Invert
Off Disable inverting the waveform.
Next Page Page1/2 Enter the second page of MATH menu.
Table 9 - Math Menu 2/2

Use arrow keys to move the vertical position of
the math waveform.
Use arrow keys to adjust the vertical scale of
the math waveform.
On Enable math waveform display.
Off Disable math waveform display.
Next page Page2/2 Return to the first menu off math waveform.
Math operations: The oscilloscope can perform math operations between

channel 1 and channel 2 and display the results as a separate waveform. It
supports addition, subtraction, multiplication, and division. When Math
menu is selected, the display will automatically display a math waveform,
such as the screenshot below:
50
Figure 21 - Math Waveform Display
FFT
FFT: Fast Fourier Transform function is supported. Toggle the

button from the Math menu 1 to change Operation to FFT to select this
function.
When FFT is selected, additional menu options are available. See table
below for the FFT menu structure.
Table 10 - FFT Menu 1/2

+ CH1+CH2
- CH1-CH2, CH2-CH1
Operation * CH1*CH2
/ CH1/CH2, CH2/CH1
FFT Fast Fourier Transform.
CH1 Selects channel 1 as FFT source.
Source
51
(see table
Window Selects FFT windowing.
below)
FFT Zoom 1X, 2X, 5X, 10X Zoom function of FFT waveform.
Table 11 - FFT Window Options
Window Characteristic Best Use Cases

The best frequency Symmetric transients or bursts.
resolution but the Equal-amplitude sine waves
Rectangular worst magnitude with fixed frequencies.
resolution. It is Broadband random noise with
essentially the same as a relatively slowly varying
having no window. spectrum.
Better frequency, Sine, periodic, and narrow-
poorer magnitude band random noise.
Hanning accuracy than
rectangular
window
Hamming has a slightly Transients or bursts pulse. The
better frequency ranges of the signals have great
Hamming
resolution than difference from before to after.
Hanning.
Best magnitude Single frequency waveforms, to
Blackman resolution but worst find higher order harmonics.
frequency resolution.
Table 12 - FFT Menu 2/2

dBVrms Set unit scale to dBVrms
Scale
Vrms Set unit scale to Vrms
Display
ToZero Selects FFT windowing.
52
On
Turn On/Off the FFT waveform.
Off
When using the FFT function, first select the channel source by toggling the
button from the FFT menu 1 to change Source between CH1 and
CH2.
Use the button from the FFT menu 1 to select the Window to use.
Descriptions of each window are provided in Table 11 - FFT Window
Options above.
Use the button in the FFT menu 1 to adjust the FFT Zoom. You can
also use the horizontal timebase keys to change the FFT Zoom.
The FFT waveform can be displayed as part of the full screen or as a split
screen from channel 1 and/or 2. Below illustrates the differences.
Figure 22 - FFT Full Screen (left), Split Screen (right)
The vertical position of the FFT waveform can be adjusted using channel 1
vertical position keys (if Source is CH1) or channel 2 vertical position keys
(if Source is CH2) . The position can always be set back to 0 by going into
FFT menu 2 and pressing to select ToZero.
53
1
2 4
FFT Display Description

1 FFT waveform position
2 FFT waveform indicator
3 FFT vertical scale
4 FFT frequency scale and sampling rate
Horizontal System
Adjust Horizontal Position
The horizontal position, or time reference position, marks the reference of

the trigger point. The position is indicated by the arrow at the top of the
display as marked in the illustration below.
54
Figure 23 - Horizontal Position Reference Marker
This position can be adjusted by using the keys to move left (<) or
right (>). If the left or right position key is pressed down for > 3 seconds,
the position change will be coarse. The scale factor is indicated as marked
by the illustration below.
Figure 24 - Horizontal Scale Indicator
The position with center reference to 0 will be displayed as you change the
position, as illustrated below:
55
Figure 25 - Horizontal Position Indicator
Adjust Horizontal Scale/Timebase
The horizontal scale or timebase scale factor can be changed using the
keys. Press S to adjust to a slower scale, and press ns to adjust

to a faster scale.
Delay Scan
The instrument has a delay scan function that can be enabled to zoom in on
a portion of the channel 1 and/or channel 2 waveforms.
To enable this, press and press to select Horizon menu.
Figure 26 - Horizon Menu
Press to toggle ON the Delayed option. When delay scan is

enabled, the display will change to split screen.
56
Figure 27 - Delay Scan
The blue shaded areas mark the masked out area and the area in between
the blue shaded area is the zoomed portion, shown at the bottom in the
split screen.
Deep Memory
The instrument’s deep memory function enable storage of a greater

number of sampling points for timebase settings between 50 ms to 25 µs.
To enable this function, go to the Horizon menu and press .
Toggle between Normal and Long Mem (deep memory) for MemDepth
(memory depth) menu option. The number of sampling points can be
computed as follows:
Sampling points = Sampling rate x Sampling time
Verify the deep memory function by following these steps:

1. Input a sine wave with 1 kHz, 4 Vpp on either channel 1 or channel
2.
2. Select a timebase between 50 ms to 25 µs. In this example, set to
100 µs.
3. Set MemDepth to Normal from the Horizon menu. Then press
, select Acquire menu and note the Sa Rate to be 12.50MSa.
57
4. Now, go back to Horizon menu and change MemDepth to Long
Mem. Go back to Acquire menu afterwards and note the Sa Rate is
now 100.0MSa.
5. The differences can be visually observed by pressing to stop
the waveform at 100 µs. Then adjust the horizontal scale factor to a
slower timebase until the entire waveform captured can be shown
on the display.
6. Observe with both MemDepth set to Normal and Long Mem.
7. Below is an example between the two captured at 100 µs timebase.
Figure 28 - Normal Memory Depth
Figure 29 - Long Memory Depth
58
Note: Different timebase settings will result in different sampling rates,
both with normal and long memory depth configured in MemDepth.
Selecting a timebase lower than 50 ms will automatically set the
instrument into scan mode. Deep memory is not supported in scan mode.
For timebase selections faster than 25 µs, the deep memory function will
have an adverse affect and will result in fewer sample points than if deep
memory is disabled.
Below is a table describing the different sampling rates for different

horizontal timebase settings with and without deep memory enabled.
Table 13 - Sampling Rate Table
Single channel Interleaved

Deep
Normal Normal
Timebase Memory Deep Memory
Sampling Sampling
Sampling Sampling Rate
Rate Rate
Rate
50 s 50 Sa/s - 50 Sa/s -
25 s 100 Sa/s - 100 Sa/s -
10 s 250 Sa/s - 250 Sa/s -
5s 500 Sa/s - 500 Sa/s -
2.5 s 1 kSa/s - 1 kSa/s -
1s 2.5 kSa/s - 2.5 kSa/s -
500 ms 5 kSa/s - 5 kSa/s -
250 ms 10 kSa/s - 10 kSa/s -
100 ms 25 kSa/s - 25 kSa/s -
50 ms 25 kSa/s 1 MSa/s 25 kSa/s 1 MSa/s
25 ms 50 kSa/s 2.5 MSa/s 50 kSa/s 2.5 MSa/s
2.5 ms 500 kSa/s 25 MSa/s 500 kSa/s 25 MSa/s
1 ms 1.25 MSa/s 50 MSa/s 1.25 MSa/s 50 MSa/s
500 µs 2.5 MSa/s 2.5 MSa/s
250 µs 5 MSa/s 5 MSa/s
100 µs 12.5 MSa/s 100 MSa/s 12.5 MSa/s
100 MSa/s
59
5 µs
2.5 µs
1 µs
250 MSa/s 250 MSa/s
500 ns
250 MSa/s
250 ns
500 MSa/s
100 ns
50 ns
25 ns 250 MSa/s
10 ns 500 MSa/s
5 ns 1 GSa/s 500 MSa/s
2.5 ns (100
MHz
models)
Vertical System
Adjust Vertical Position
The vertical position of channel 1 and channel 2 are marked on the left side
of the display, as illustrated below:
Figure 30 - Vertical Position Markers
60
To move the vertical position up or down, use the left vertical position keys
(for CH1) or right vertical position keys (for CH2) . If the up or down key
is pressed down for > 3 seconds, the position change will be coarse. The
vertical position relative to center 0 reference will be indicated when
changed, as illustrated below:
Figure 31 - Vertical Position Indicator
Adjust Vertical Scale
The vertical scale factor can be adjusted by pressing the left volts/div range
keys (for CH1) or the right volts/div range keys (for CH2) . To increase
the scale, press V. To decrease, press mV.
By default, the volts/div range keys will change the vertical scale factor in 1-
2-5 increments. Users can select fine control so that the change will be
finer in increments of 10 mV per key press. To do this, press either or
and press in the channel menu to select Fine for Volts/Div

menu option.
61
Figure 32 - Fine Control Volts/Div
Reference Waveform Menu
The instrument can save and display two reference waveforms from both
channel 1 and/or channel 2. A reference waveform copies the source
waveforms’ vertical position, vertical scale factor, horizontal position, and
horizontal scale factor.
To access the Reference menu, press and to select Ref.
Below is a table of the Reference menu structure.
Table 14 - Reference Waveform Menu
Menu Description
Setting
Option
CH1/CH1 Off Choose the channel to save as a reference
Source
CH2/CH2 Off waveform.
Ref A Choose to save or recall reference A or
Ref B reference B waveform.
Save the source waveform to the selected
Save
reference (A or B).
62
On Toggles displaying the reference waveform.
Ref A/Ref B
Off
Note: Under Source, CH1 Off and CH2 Off will be displayed if both channel
1 and 2 are turned Off.
Saving a Reference Waveform
Follow the steps below to save a reference waveform.
1. Setup and adjust all parameters of the waveform exactly as you

want saved from channel 1 or channel 2.
2. Go into the Ref menu by pressing and .
3. Under Source, select CH1 or CH2 as the waveform you want to save.
4. You can save two reference waveforms, therefore select REF A or
REF B by toggling .
5. Press to select Save and now the reference waveform is
saved.
6. To display the waveform, toggle to turn On or Off. The
below screenshot displays both REF A and REF B copied from
channel 1 and channel 2. REF A is in red and REF B is in purple.
Figure 33 - Reference Waveforms Display
63
3.5 Trigger System
There are five types of trigger functions supported by the instrument: edge,
pulse, video, slope, and alternative.
Adjust Trigger Level
To adjust the trigger level in all trigger modes, use the or

arrow keys to move up or down.
The trigger level position is marked by T on the right of the display. When
changed, the screen will temporarily display the trigger level line across the
window with the trigger position indicator in the bottom left corner, as
illustrated below:
Figure 34 - Trigger Level Display
Note: Some options within the trigger menu share the same arrow keys
used to adjust the trigger level. In which case, exit the trigger menu by
pressing first, then the arrow keys can be used to change the
trigger level.
To access the Trigger menu, press . The following describes each

type of trigger and the menu options available for setting it up.
64
Edge Trigger
Edge trigger seeks to trigger off of a specified slope and level of a

waveform.
Select Edge under Type from the trigger menu.
Table 15 - Edge Trigger Menu
Menu
Setting Description
Option
Trigger on the rising or falling edge of the input
Type Edge
signal.
CH1
Source Set CH1 or CH2 as the trigger source.
CH2
Trigger on rising edge of the trigger signal.
Trigger on falling edge of the trigger signal.
Slope
Trigger on rising and falling edge of the trigger
signal.
Use this mode to let the acquisition free-run in
the absence of a valid trigger; This mode allows
Auto
an un-triggered, scanning waveform at 100
ms/div or slower time base settings.
Mode Use this mode when you want to see the
Normal triggered waveforms only; the scope will not
acquire waveform until it’s been triggered.
The setup detects a trigger and acquires
Single
waveform, then stops to give a signal capture.
Set Up Enter the Edge Trigger Setup Menu.
65
Table 16 - Edge Trigger Setup Menu
Menu
Setting Description
Option
DC Passes all components of the signal
Blocks DC components and attenuates
AC
signals below 170 Hz.
Attenuates the high-frequency
Coupling HF Reject
components above 140 kHz.
Blocks the DC component and attenuates
LF Reject the low-frequency components below 7
kHz.
Adjusts the hold off time.
Hold off
Hold off
Reset hold off time to 100 ns.
Reset
Return Return the Edge Trigger Menu.
Hold Off: To adjust the hold off time, go to the Edge Trigger Setup Menu
and press , then use the or arrow keys to adjust

the hold off time, which will be displayed when it is adjusted.
Hold off time can be reset to 100 ns by pressing to select Hold Off
Reset.
66
Figure 35 - Hold Off Time Indicator
Pulse Trigger
Pulse trigger seeks certain pulse conditions of a waveform to trigger.
Select Pulse under Type from the trigger menu.
Table 17 - Pulse Trigger Menu 1/2
Menu
Setting Description
Option
Type Pulse Select the pulse trigger function.
CH1 Set CH1 or CH2 as the trigger
Source
CH2 source.
67
(Positive pulse width
less than pulse width set)
larger than pulse width
setting)
equal to pulse width
setting) Select the pulse trigger
When (Negative pulse conditions; it triggers as soon as
width less than pulse width condition is met.
setting)
(Negative pulse
width larger than pulse
width setting)
(Negative pulse
width equal to pulse width
setting)
Set 20.0 ns - 10.0 s Set the pulse width for pulse
Width trigger condition.
Next Enter the second page of the
Page 1/2
Page Pulse Trigger Menu.
Table 18 - Pulse Trigger Menu 2/2
Menu
Setting Description
Option
Select the pulse to trigger the pulse match the
Type Pulse
trigger condition.
Auto
Select the type of triggering; Normal mode is
Mode Normal
best for most Pulse Width trigger applications.
Single
Enter the Pulse Trigger Setup Menu. See
Setup
Table 16 for details.
Return to the first page of the Pulse Trigger
Next Page Page 2/2
Menu.
68
To set the pulse width for the pulse trigger condition, press in the
Pulse Trigger menu 1 to select Set Width and use or arrow

keys to adjust the width, which will be displayed when it is adjusted.
Figure 36 - Pulse Width Trigger Condition Display
Note: Trigger level cannot be changed while the Pulse Trigger Menu is
active because the SetWidth option shares the same arrow keys to make
changes.
Video Trigger
Video trigger can be used to capture waveforms of standard NTSC and

PAL/SECAM analog video signals.
Select Video under Type from the trigger menu.
Table 19 - Video Trigger Menu 1/2
Menu
Setting Description
Option
69
Select Video trigger. To trigger NTSC, PAL and
Type Video
SECAM video signals, set coupling to AC.
CH1
Source Set CH1 or CH2 as the trigger source.
CH2
Normal trigger on the negative edge of the sync
(Normal)
pulse.
Polarity
Inverted trigger on the positive edge of the sync
(Inverted) pulse.
All Lines
Line Num
Sync Select appropriate video sync.
Odd Field
Even Field
Next
Page 1/2 Enter the second page of Video Trigger Menu.
Page
Sync: The bottom right of the display indicates the Sync setting the
instrument is configured to.
All Lines The video trigger will sync on all lines of the
signal.
Line Num Select a specific line number for video trigger.

Odd Field Select only the odd lines for video trigger.
Even Field Select only the even lines for video trigger.
Line Num: To change the line number for video trigger, use the or
arrow keys. The selected line number will be indicated in the

bottom right corner.
Note: Trigger level cannot be changed while the Video Trigger Menu is
active because the Line Num Sync option shares the same arrow keys to
make changes.
70
Table 20 - Video Trigger Menu 2/2
Menu
Setting Description
Option
When you select type video and select
Type Video AC coupling, you could trigger to a
NTSC, PAL and SECAM video signal.
NTSC, Select the video standard for sync and line
Standard
PAL/SECAM number count.
Use this mode to let the acquisition free-
run in the absence of a valid trigger. This
Auto mode allows an un-triggered, scanning
waveform at 100 ms/div or slower time
base settings.
Mode
Use this mode when you want to see only
triggered waveforms; the oscilloscope does
Normal
not display a waveform until after the first
trigger.
Single Use this mode to run a single capture.
Enter the Video Trigger Setup Menu. See
Setup
Table 16 for details.
Return the first page of Video Trigger
Next Page Page 2/2
Menu.
Table 21 - Video Trigger Setup Menu
Menu
Setting Description
Option
Adjusts the hold off time.
Hold off
Hold off
Reset hold off time to 100 ns.
Reset
71
Return Return to the Video Trigger Menu.
Slope Trigger
Slope trigger can be used to trigger off a rising or falling edge with specified
slope timing conditions and vertical boundaries. It is similar to Edge trigger
but with more options users can setup to seek for specific slope conditions
from the selected source.
Select Slope under Type from the trigger menu.
Table 22 - Slope Trigger Menu 1/2
Menu
Setting Description
Option
Trigger on positive slope or
Type Slope
negative slope.
CH1
Source Select trigger source.
CH2
(rising edge greater

than slope time
(rising edge less than
slope time)
(rising edge equal to
slope time)
When Select trigger conditions.
(falling edge greater
than slope time)
(falling edge less than
slope time)
(falling edge equal to
slope time
72
Use the arrow keys to set
Time Set time slope time. The time range is
20 ns – 10 s.
Enter the second page of the
Next Page Page 1/2
Slope Trigger Menu.
Table 23 - Slope Trigger Menu 2/2
Menu
Setting Description
Option
Type Slope Select slope trigger.
(Set high trigger level
position of rising edge)
(Set low trigger level
position of rising edge)
(Set high and low
Selects the high and low trigger
trigger level position of rising
level that can be adjusted for
edge)
Vertical slope trigger. Use this to set
(Set high trigger level
the boundaries for the slope
position of falling edge)
trigger.
(Set low trigger level
position of falling edge)
(Set high and low
trigger level position of
falling edge)
Use this mode to let the
acquisition free-run in the
absence of a valid trigger; This
Auto mode allows an un-triggered,
scanning waveform at 100
Mode ms/div or slower time base
settings.
Use this mode when you want
to see only triggered
Normal
waveforms; the oscilloscope
does not display a waveform
73
until after the first trigger.
Use this mode to run a single
Single
capture.
Enter the Slope Trigger Setup
Setup
Menu. See Table 16 for details.
Return to the first page of the
Next Page Page 2/2
Slope Trigger Menu.
Alternative Trigger
Alternative trigger will alternate the trigger between two channels to allow
triggering both channels. Trigger types can be set to Edge, Pulse, Video, and
Slope. Trigger information will be displayed at the bottom right of the
screen.
Table 24 - Alternative Trigger Menu
Menu
Setting Description
Option
Type Alternative Select alternative trigger.
CH1
Source Select trigger source.
CH2
Edge
Pulse
Mode Select trigger type for the alternative trigger.
Video
Slope
See
74
If Mode is Edge, see Edge Trigger section.
Next
If Mode is Pulse, see Pulse Trigger section.
Page/Set
If Mode is Video, see Edge Trigger section.
up
If Mode is Slope, see Slope Trigger section.
Table 25 - F4 option in Alternative Trigger Menu
Menu
Setting Description
Option
Slope Edge trigger option. See Table 15 for details.
When Pulse trigger option. See Table 17 for details.
Polarity Video trigger option. See Table 19 for details.
When Slope trigger option. See Table 21 for details.
3.6 Connecting External Memory

The instrument supports saving and recalling files of different types, as
described in the following section “3.7 Save/Recall Function”, to and from
an external USB flash memory drive.
To connect an external USB flash drive, plug the drive into the USB host port
on the side of the instrument as labeled in “Figure 4” in section “1.6 Side
Panel Overview”.
If the USB flash drive is recognized by the instrument, it will display the
following prompt:
75
Figure 37 - USB Drive Detected
When the USB flash drive is removed from the USB host port, the following
prompt will display:
Figure 38 - USB Drive Removed
3.7 Save/Recall Function

Instrument setups and waveform traces can be saved and recalled into both
internal memory and external memory (USB flash drive). Additionally,
screen images and waveform data can be saved as well to external memory.
Enter the Save/Rec menu by pressing .
76
Table 26 - Save/Recall Menu
Menu
Setting Description
Option
Setups Select to save instrument settings/setups.
Waveforms Select to save the waveform traces on screen.
Type Picture Select to save the screenshot as a .BMP file.
CSV Select to save the waveform data as a .CSV file.
Factory Select to set instrument to default settings.
Device Select to save the file into internal memory.
Save to
File Select to save the file into external memory.
Choose the position number to save/recall
Setup No.1 to No.20
setups.
Select to save instrument setups or waveform
Save
traces.
Select to recall instrument setups or waveform
Recall
traces.
Table 27 - Save Screenshot Menu
Menu
Setting Description
Option
Type Picture Select to save the screenshot as a .BMP file.
Save Picture Select to save screenshot to external memory.
Print Picture Print option is not supported.
77
Select to save bitmap image to external
memory. (This option is available when a USB
Save
flash drive is connected and detected by the
instrument)
Table 28 – Save Waveform Data Menu
Menu
Setting Description
Option
Type CSV Select to save the waveform data as a .CSV file.
Displayed Select to save only the waveform data
Data
displayed within the grid.
Depth
Maximum Select to save all captured waveform data.
Para On Choose to save scope parameters in the data
Save Off file.
Select to save waveform data into external USB

Save
flash drive.
NOTE:
If Data Depth is set to Maximum, it may take several
minutes to complete the save process. Do not press
any key during the save process.
Saving and Recalling Setups and Waveforms
Instrument setups and waveform traces can be saved into internal and
external memory.
78
To save setups and waveforms, follow the steps below:
1. Press to go into the Save/Recall menu, then select Type.
2. Toggle to choose Setups to save instrument setups, or
choose Waveforms to save waveform traces on display.
3. To save the file into internal memory, press to set Save To
to Device. To save the file to external memory, set it to File and go
to step 5.
4. If Save To is set to Device, toggle to choose the internal
memory location to save the file to. There are total of 20 storage
locations (No.1 – No.20).
5. Now, press to Save and the current instrument settings
will be stored into the configured memory location. If saving to
external memory, the directory explorer will display, as shown
below. Here, you can choose to create a new directory or new file
to save as your file.
Figure 39 - Directory Menu 1/2
6. To create a new directory, toggle to set Modify option to

Directory. Then, press to select New Dir. And the
following screen will display:
79
Figure 40 - Create Directory Name
7. You can set the name using the on screen virtual keypad. Use
and keys to move the cursor position of the
name to left and right respectively. To select a character to insert at
the cursor position, use the and arrow keys to

move the selection cursor to the character you want to select.
8. Then, press to select InputChar. You can also press

arrow key to do the same.
9. To delete a character at the cursor position in the name, select
DeleteCharacter in the on screen keypad, then press ,
which will say Delete Char when DeleteCharacter is selected from
the virtual keypad.
10. To save with the configured name, select Confirm from the menu by
pressing .
11. The folder will be created. Now, to save the file, set Modify option
to Files.
12. Then, press to select New File. Follow the same steps 7-10
to create a file name. The new setup or waveform file will then be
created onto the external memory. This process may take 10-15
seconds. A progress bar will be displayed to show the instrument’s
save progress.
80
Figure 41 - Save Progress
If the file saves successfully, a message will prompt as shown below:
Figure 42 - Save Successfully
13. If the file name is found to be the same as another file already in the
external memory, the instrument will prompt an overwrite warning.
Press to select Confirm to overwrite the file, or press
to select Cancel.
81
Figure 43 - Overwrite Warning
14. To exit the Directory menu, press to go to Directory Menu

2, then press to select Return.
Note: Instrument setups will be saved as a .SET file and waveform traces
will be saved as a .DAV file. Both of these file types can only be recalled
from within the oscilloscope Save/Recall menu.
To recall setups or waveforms, do the following:

1. From the Save/Recall menu, select the Type to Setups or
Waveforms depending on the type of file you want to recall.
2. Then, set Save To as Device to recall from internal memory.
3. Select the storage location you want to recall from by pressing
under Waveform option, then press to select
Recall. The setup or waveform will be recalled from the selected
location.
4. To recall from external memory, set Save To as File, then press
to select Recall.
5. The Directory menu will come up. Use the and

arrow keys to highlight the .DAV (waveform) or .SET (setup) file you
want to recall, then press to select Load. If the file is
within another folder in the directory, select and open the directory
82
by pressing . To go back up a folder, just press it again with
cursor selecting UP.
Figure 44 - Subdirectory View
Saving Screen Capture
The screen capture can be saved as a .BMP file to external memory. To do

this, select Picture as Type from the Save/Recall menu. Press so
that it says Save Picture. Then press to select Save option. The
Directory menu will come up.
Similar to the instructions given for saving setups and waveforms to

external memory, create a new file and name to save it into the external
memory as a .BMP file.
Saving Waveform Data
Follow the steps below to save waveform data into external memory:
1. From the Save/Recall menu, toggle to select CSV for Type.
83
2. Then, select Data Depth as Displayed or Maximum. (See “Table 28”
for description of the options)
3. Then, select Para Save as On or Off. Set to On if you want scope
parameters (i.e. timebase, volts/div) to be saved along with the
waveform data.
4. Press to select Save.
5. Similar to saving a screenshot image, setups, and waveform traces
as instructed in previous sections above, you will enter the Directory
menu.
6. Create a new file to save as and the file will be saved to external
memory as a .CSV file.
NOTE:
If Data Depth is set to Maximum, it may take several
minutes to complete the save process. Do not press
any key during the save process.
3.8 Utility Menu

The utility menu contains menu options for configuring the oscilloscope. To
access the menu, press .
Table 29 - Utility Menu 1/4
Menu
Setting Description
Option
System Displays the instrument
Status information.
Enable key sound.
Sound
Disable key sound.
On Turn ON the frequency counter.
Counter
Off Turn OFF the frequency counter.
84
English, Français, 日本語,
한국의, Deutsch, Español,
Language русский, Italiana, Select the interface language.
Português, ‫ال عرب ية‬, Polish,
简体中文, 繁體中文
Next
Page 1/4 Enter the next page of the menu.
Page
Menu
Setting Description
Option
Do a self calibration to calibrate the
Do Self Cal
channels.
Screen Test Run the screen detect program
Do Self Test
Keyboard Test Run the keyboard detect program
Print Setup Not supported.
Printer Not supported
Select to allow remote communication with
USB Device
Computer application software via the miniUSB port
on the side panel.
Next Page Page 2/4 Enter the third page of the menu.
Menu
Setting Description
Option
Update firmware Select to update firmware.
85
Press this button to enter the Waveform
Record
Record Menu.
Next Page Page 3/4 Enter the fourth page of the menu.

1min, 2min,
5min, 10min,
Screen saver 15min, 30min, Set the screen saver time.
1hour, 2hour,
5hour, Off
Configure date and time (see section 2.6

Date/Time
Configure Date and Time).
Next Page Page4/4 Return to the first page of the menu.
Check System Information
To check the model information, serial number, software firmware version,

and hardware version, enter the UTILITY menu by pressing . Then,
from Utility Menu 1/4, select System Status by pressing . The
following screen will display, showing all the system information.
86
Figure 45 - System Information Display
To exit and go back to the main menu, press .
Enable/Disable Key Sound
The key press sound can be enabled or disabled from the Utility Menu 1/4.
Press to toggle the Sound option to enable or disable key sound.
Enable/Disable Frequency Counter
The oscilloscope has a built-in counter to display frequency when a signal

from channel 1 or channel 2 is measurable.
To turn it ON or OFF, toggle the button in Utility Menu 1/4 to

change the Counter option. Frequency counter will be displayed in the
lower right corner, as illustrated below:
87
Figure 46 - Frequency Counter Display
Set the Language
The interface can be displayed in different languages. Supported languages

are: English, French, Japanese, Korean, German, Spanish, Russian, Italian,
Portuguese, Arabic, Polish, Simplified Chinese, and Traditional Chinese.
From the Utility Menu 1/4, toggle to change the language.
Updating Firmware
Firmware updates are available on B&K Precision’s website at

www.bkprecision.com .
To update the firmware, do the following:
1. Download the firmware file from www.bkprecision.com

2. Save the firmware file to a USB flash drive. The file will have an .ADS
extension.
3. Power On the instrument and connect the USB flash drive to the
USB host port on the side of the instrument (See “1.6 Side Panel
Overview” for details).
88
4. Press to enter the Utility Menu and press to go to
page 3/4 of the menu.
5. Select Update Firmware by pressing .
6. To proceed, press . Otherwise, press to exit out

of the firmware update menu.
7. From the Directory menu, use the and arrow

keys to select the firmware file stored in the USB flash drive.
8. Once selected, select Load by pressing .
9. At this point, the instrument will begin updating the firmware.
WARNING:
Do not power off the instrument or press any of the
front panel keys at any time during the update
process. Any power interruption or key press
interruption may damage the instrument or corrupt
the firmware, causing it to malfunction and void the
warranty.
10. Wait for 1-2 minutes for the update to finish. A progress bar on the
display will indicate when update is complete.
11. When finished, a prompt will say “Update Successfully” and will
prompt the user to reboot the instrument.
12. At this point, power off the instrument by holding down for at
least three seconds, then power back on again.
13. To verify that the instrument has updated successfully, press
to go to the Utility menu and press from page 1 of the
menu to select System Status.
89
Set Screen Saver
The instrument has a screen saver mode to save power when the
instrument is idle or not in use. The timer to enable the screen saver can be
configured by going to page 4 of the Utility menu and pressing to
select Screen saver option. Toggle this to change the screen saver timer.
Select Off to disable the screen saver.
Waveform Record Function
The waveform record function can record channel 1 or channel 2 input

signals frame by frame from 1 up to 2500 frames. The recorded frames can
be played back for analysis.
NOTE:
Record function is not available when Alternative
Trigger is selected. Single trigger is also not
supported when using this function.
To access the waveform record function, press and press

to get to Utility menu page 3. Press to select Record to enter the
Record menu.
By default, Mode is set to Off, so no other menu options will be available.

To configure the waveform record function, press to select Record
for Mode.
90
Table 33 - Waveform Record Menu
Menu
Setting Description
Option
Record Set to configure and record.
Mode Replay Set to playback recorded waveform.
Off Turn off waveform record menu.
Source CH1, CH2 Choose recorder source.
Set interval to record waveform. (1 ms
Interval
– 1000 s)
Set the maximum number of frames
End Frame
to record. (1 – 2500)
Start to record
Operate
Stop recording
Configure Waveform Record
1. Select the source to record by toggling to select CH1 or

CH2 for Source option.
2. Select the interval to which to record a frame by pressing
first to select Interval, then use the and arrow

keys to change the interval time.
3. Press to select End Frame to set the number of frames to
record. Use the and arrow keys to change the

number.
4. To begin recording, press so that under Operate menu
option, it shows the icon. This indicates that the waveform is
being recorded.
91
An indicator at the top left of the grid display will indicate the approximate
frame count of the recording.
Figure 47 - Record Frame Indicator
When recording is finished, the following message will be prompted:
Figure 48 - Recording Finished
92
Playback Recorded Waveform
To playback a recorded waveform, select Playback for Mode in the

Waveform Record menu. Playback menu options are available to configure
playback. Once configured, press in page 1 of the menu to start
playback. Press it once more to stop playback at any time.
Table 34 - Waveform Playback Menu 1/2
Menu
Setting Description
Option
Mode Play Back Set to playback recorded waveform.
Press to start playback.
Operate
Press to stop playback.
Set to repeat playback.
Play Mode
Set to run playback one time.
Set interval between frames during
Interval
playback.
Next Page Page 1/2 Enter the second page of the menu.
Table 35 - Waveform Playback Menu 2/2
Menu
Setting Description
Option
Start Frame Set start frame.
Curr_Frame Select current frame to be played.
93
End Frame Set end frame.
Return Press to exit back to the Utility menu.

Next Page Page 2/2 Return to the first page of the Playback menu.
3.9 Measurement and Cursor Functions
Measurement Functions
NOTE:
The measurement function will not make automatic
measurements when the instrument is in SCAN mode.
Time base must be ≤ 50 ms.
The instrument has many built-in automatic measurement functions

available, which are categorized by voltage measurements, time
measurements, and delay measurements.
To access the measurement function menu, press until the

Measure menu is displayed.
By default, the menu options will show five different measurements in the
menu display area. Each of these 5 measurements can be changed to show
different measurements by selecting its corresponding function key
( - ).
In the Measure menu, press any of the function keys to go to the

measurement selection menu, as shown below.
94
Table 36 - Measurement Selection Menu
Menu Option Description

Voltage Press this button to enter the Voltage measure menu.
Time Press this button to enter the Time measure menu.
Delay Press this button to enter the Delay measure menu.
All Mea Press this button to enter the All Measurement menu.
Return Return to the Measure menu.
Select the measurement parameters, then configure the type of

measurement to display. When finished, press Return option to
go back to the Measure menu, and the corresponding menu option will
now display the selected Measurement Parameter.
Voltage Measurement Parameters
Table 37 - Voltage Measurement Parameters Menu
Menu
Setting Description
Option
Select input signal source for
Source CH1,CH2
voltage measurement.
Vpp, Vmax, Vmin, Vamp, Vtop,
Select the type of voltage
Type Vbase, Vavg, Mean, Vrms, Crms,
measurement.
FOV, FPRE, ROV, RPRE
, , , Display the corresponding icon
, , , for the selected voltage
, , , measurement as well as the
, measured value.
95
Vpp – Voltage peak-to- Mean – Arithmetic mean
peak over the entire waveform
Vmax – Positive peak Vrms – True rms voltage
voltage over the entire waveform
Vmin – Negative peak Crms – rms voltage of the
voltage first cycle of the waveform
Vamp – Vtop and Vbase FOV – Falling edge
difference overshoot voltage
𝑉𝑚𝑖𝑛 − 𝑉𝑏𝑎𝑠𝑒
𝐹𝑂𝑉 =
𝑉𝑎𝑚𝑝
Vtop – Max. voltage FPRE– Falling edge
during measurement preshoot
𝑉𝑚𝑎𝑥 − 𝑉𝑡𝑜𝑝
𝐹𝑃𝑅𝐸 =
𝑉𝑎𝑚𝑝
Vbase – Min. voltage ROV – Rising edge
during measurement overshoot voltage
𝑉𝑚𝑎𝑥 − 𝑉𝑡𝑜𝑝
𝑅𝑂𝑉 =
𝑉𝑎𝑚𝑝
Vavg – Average voltage RPRE – Rising edge
over first cycle preshoot
𝑉𝑚𝑖𝑛 − 𝑉𝑏𝑎𝑠𝑒
𝑅𝑃𝑅𝐸 =
𝑉𝑎𝑚𝑝
Time Measurement Parameters
Table 38 - Time Measurement Parameters Menu
Menu
Setting Description
Option
Source CH1, CH2
Time measure.
Period, Freq, +Wid, -Wid, Rise Select the type of time
Type
Time, Fall Time, BWid, +Dut, - measurement.
96
Dut
Display the corresponding icon
, ,
for the selected time
, ,
measurement as well as the
, ,
measured value.
Period – Period of the Fall Time – Time between

signal voltage level falling from
90% to 10%
Freq – Frequency of the BWid – Duration of a
signal burst over entire
waveform
+Wid – Time between first +Dut – Ratio between
rising edge and next falling first positive pulse width
edge at 50% voltage level and period
-Wid – Time between first -Dut – Ratio between first
falling edge and next rising negative pulse width and
edge at 50% voltage level period
Rise Time – Time between
voltage level rising from
10% to 90%
Delay Measurement Parameters
Table 39 - Delay Measurement Parameters Menu
Menu
Setting Description
option
Source CH1, CH2
delay measure.
Type Phase, FRR, FRF, FFR, FFF, Select the type of delay
97
LRR, LRF, LFR, LFF measurement.
Display the corresponding icon
, ,
for the selected delay
, ,
measurement as well as the
, ,
measured value.
Phase – Phase difference LRR – Time between first rising

between two waveforms edge of CH1 and last rising
edge of CH2
FRR – Time between first LRF – Time between first rising
rising edge of CH1 and edge of CH1 and last falling
first rising edge of CH2 edge of CH2
FRF – Time between first LFR – Time between first
rising edge of CH1 and falling edge of CH1 and last
first falling edge of CH2 rising edge of CH2
FFR – Time between first LFF – Time between first
falling edge of CH1 and falling edge of CH1 and last
first rising edge of CH2 falling edge of CH2
FFF – Time between first
falling edge of CH1 and
first falling edge of CH2
Display All Measurements
You can enable all voltage measurements, all time measurements, or all
delay measurements to display on the screen. You can also show all 32
total automatic measurements on the display.
From the Measure menu, press to select All Mea.

Then, select the single source to show its corresponding measurements by
toggling to set Source as CH1 or CH2. Press to toggle On
or Off displaying all voltage measurements. Press to toggle On or
Off displaying all time measurements. Press to toggle On or Off
displaying all delay measurements.
98
Table 40 - All Measurement Display Menu
Menu
Setting Description
option
Source CH1, CH2
delay measure.
Select to enable/disable
On
Voltage displaying all voltage
Off
measurements.
On
Time displaying all voltage
Off
measurements.
On
Delay displaying all delay
Off
measurements.
Figure 49 - All Voltage Measurements Display
99
Figure 50 - All Time Measurements Display
Figure 51 - All Delay Measurements Display
Figure 52 - All Measurements Display
100
Cursor Functions
Toggle the button to enter the Cursor menu.
There are three cursor modes available: Manual, Track, and Auto.
To disable cursors, set Mode to Off.
Manual Cursor Mode
Manual cursor mode allows users to set either horizontal or vertical cursors
to make measurements from a selected signal source.
From the Cursor menu, set Mode to Manual. Select the Type of cursor for
the measurement, and select Source.
To adjust Cursor A, select it with to that it’s highlighted, then use
the and arrow keys to adjust its position. Do the same

to adjust Cursor B by selecting it with .
Note: MATH, REFA, and REFB are not selectable as Source unless they are
enabled. Refer to “3.4 Scope Menu” to enable them.
Table 41 - Manual Cursor Menu
Menu
Setting Description
Option
Mode Manual Set to manual cursor mode.
Use cursors to measure voltage
Voltage
Type parameters.
Time Use cursors to measure time parameters.
Source CH1, CH2, Choose the signal source to measure with
101
MATH, REFA, cursors.
REFB
Cur A Adjust cursor A position.
Cur B Adjust cursor B position.
Voltage Type – Voltage cursors are used to make cursor measurements.

Two horizontal cursor lines will appear on the display, and their positions
and differences will be indicated in the upper left corner of the display.
5
4 1
3
Figure 53 - Manual Voltage Cursor
1 Cursor A
2 Cursor B
3 Cursor A position
4 Cursor B position
5 Voltage difference between Cursor A and Cursor B
102
Time Type – Time cursors are used to make cursor measurements. Two
vertical cursor lines will appear on the display, and their positions and
differences will be indicated in the upper left corner of the display.
6
5
1
4
3
Figure 54 - Manual Time Cursor
1 Cursor B
2 Cursor A
3 Cursor A time position
4 Cursor B time position
5 Frequency between Cursor A and Cursor B
6 Time difference between Cursor A and Cursor B
103
Track Cursor Mode
Track cursor mode allows users to setup two cursors with both time and
voltage tracked from selected signal sources.
From the Cursor menu, set Mode to Track. Select the source for Cursor A
and the source for Cursor B by toggling and respectively.
To adjust Cursor A, select it with to that it’s highlighted, then use
the and arrow keys to adjust its position. Do the same

to adjust Cursor B by selecting it with .
Table 42 - Track Cursor Menu
Menu
Setting Description
Option
Mode Track Set to track cursor mode.
CH1, CH2,
Cursor A Select signal source for cursor A to measure.
NONE
CH1, CH2,
Cursor B Select signal source for cursor B to measure.
NONE
Cur A Adjust cursor A position.
Cur B Adjust cursor B position.
104
9
8
7
6
5
4
3
2
1
Figure 55 - Track Cursor Display
1 Cursor B
2 Cursor A
3 Voltage difference between Cursor A and Cursor B
4 Frequency between Cursor A and Cursor B
5 Time difference between Cursor A and Cursor B
6 Cursor B voltage position
7 Cursor B time position

8 Cursor A voltage position
9 Cursor A time position
Auto Cursor Mode
Auto cursor mode is used for automatic measurements only. When

selecting Mode as Auto from the Cursor menu, no additional menu options
will appear.
105
In this mode, the cursor(s) will be displayed when selecting automatic
measurements.
For example, toggle to go to Measure menu.
Select any of the five measurements displayed in the menu display area,
then select any measurement parameter types.
Selecting Vpp as the voltage measurement Type will show the following
display, with two cursors shown on display to illustrate their positions to
which the measurements are being made.
Figure 56 - Auto Cursor Measuring Vpp
Selecting Period as the time measurement Type will show the following
display, with two cursors shown on display to illustrate their positions to
which the measurements are being made.
106
Figure 57 - Auto Cursor Measuring Period
Note: Auto cursor mode does not support displaying

cursors for multiple measurements.
107
4 Using the Digital Multimeter
The handheld digital storage oscilloscope has a built-in multimeter that can
measure DC and AC voltage, DC and AC current, resistance, diode,
continuity, and capacitance.
To set the instrument to the digital multimeter mode, press , and

the display will enter the multimeter display, as shown below.
Figure 58 - Multimeter Display
Mode and input indicators

to illustrate the current
meter function and which
inputs to connect to
externally to make
measurements.
Actual measured reading for
the selected measurement
function. Top right
indicates ranging mode
(AUTO or MANUAL).
Bar graph meter of the
measured value.
108
Note: In the digital multimeter mode, only the function
keys ( - ), , and
keys are active. All other front panel

keys, besides and are inactive
and are unused.
CAUTION:
Always use only the included test leads to make
measurements. Verify that test leads are in
proper working conditions and that they meet the
specified electrical ratings and input requirements
of the instrument.
4.1 DC and AC Voltage Measurements
To measure DC voltages, press repeatedly until Meter is set to

DCV.
To measure AC voltages, press repeatedly until Meter is set to

ACV.
109
Table 43 – DC/AC Voltage Measurement Menu

Save the current input value as a reference
value. Subsequent measurements will be the
On
Relative difference from the reference value. This is
same as “zeroing” the meter.
Off Relative mode is disabled.
Auto Select to enable autoranging.
Manual Select to enable manual ranging.
Display measurement in volts (V). In manual
V ranging, only the volts (V) ranges are
selectable.
Display measurement in millivolts (mV). In
mV manual ranging, only the millivolts (mV) ranges
are selectable.
Enters the Meter Trend plot mode (See “Meter
Trend Plot
Trend Plot” for more information).
DC Voltage Measurement
Configure all settings from the menu.

When set for Manual ranging (select Manual by toggling ), use the
key to increase the range. At the highest range, pressing this will
automatically go back to the lowest range.
DC Voltage ranges: 60 mV, 600 mV, 6 V, 60 V, 600 V, 1000 V.
NOTE: When the measurement unit is changed, range

will automatically change to Auto ranging.
NOTE: If the measurement is out of range or if manual

range is used and the measurement is outside of
the selected range, the instrument will beep
continuously. The measurement display will show
0.L.
110
Figure 59 - Out of Range
CAUTION:
Always connect the test leads to the instrument
inputs first before probing the DUT to avoid
potential shock hazard.
Follow these steps to make a measurement.

1. Connect the negative (-) side with the black test lead to the COM
input.
2. Connect the positive (+) side with the red test lead to the V.Ω.C
input.
3. Probe with the test leads to the DUT and take the measured reading
on display.
10 A mA COM V.Ω.C
- +
DC Voltage
Figure 60 - Connection for DC Voltage Measurement
111
WARNING:
Never connect more than 1000V DC across the
input terminals.
AC Voltage Measurements
AC voltage measurements use the same setup as DC voltage

measurements.

AC Voltage ranges: 60 mV, 600 mV, 6 V, 60 V, 600 V, 750 V.

CAUTION:
inputs first before probing the DUT to avoid

1. Connect the black test lead to the COM input.
2. Connect the red test lead to the V.Ω.C input.
on display.
NOTE: If the measurement is out of range or if manual

range is used and the measurement is outside of
the selected range, the instrument will beep
continuously.
112
10 A mA COM V.Ω.C
AC Voltage
Figure 61 - Connection for AC Voltage Measurement
WARNING:
Never connect more than 750V AC across the
input terminals.
4.2 DC and AC Current Measurements
To measure DC current, press repeatedly until Meter is set to DCI.
To measure AC current, press repeatedly until Meter is set to ACI.
Table 44 – DC/AC Current Measurement Menu

On
Relative difference from the reference value. This is the
A Display measurement in amps (A). In manual
113
ranging, only the amp (A) ranges are selectable.
Display measurement in milliamps (mA). In
mA manual ranging, only the milliamp (mA) ranges
are selectable.
Trend Plot
DC Current Measurements
Current measurements can be made in low current or high current mode. In

low current measurement mode you can measure up to 600 mA. Connect to
the low current mA terminal and select one of the two ranges. In high
current measurement mode, you can measure up to 10 A by selecting one
of the two ranges and connecting to the 10A input terminal.

DC Current ranges: 60 mA (low), 600 mA (low), 6 A (high), and 10 A (high).
CAUTION:
inputs first before connecting the DUT to avoid
Low Current Measurements (< 600 mA)
Follow these steps to make measurements < 600 mA.

input.
2. Connect the positive (+) side with the red test lead to the mA input.
on display.
114
10 A mA COM V.Ω.C
A
+ -
DC Current
Figure 62 - Connection for Low DC Current Measurement
WARNING:
Do not connect more than 600 mA DC current
across the mA input terminal or the protection
fuse will trip. Never input 10 A or more current
across the terminal or the instrument will be
damaged and warranty will be void.
Higher Current Measurements (Up to 10 A)
Follow these steps to make measurements up to 10 A.

input.
2. Connect the positive (+) side with the red test lead to the 10A input.
on display.
10 A mA COM V.Ω.C
A
+ -
DC Current
Figure 63 - Connection for Higher DC Current Measurement
115
WARNING:
Do not connect more than 10 A DC current across
the 10A input terminal or the protection fuse will
be tripped.
Make AC Current Measurements
For current measurements, the low current measurement mode supports

two ranges. Use the low current mA input terminal to measure current up
to 600 mA. High current measurements also support two ranges. In this
mode you can measure up to 10 A by connecting to the 10A input terminal.
AC Current ranges: 60 mA (low), 600 mA (low), 6 A (high), and 10 A (high).
CAUTION:
Low Current Measurements (< 600 mA)
Follow these steps to make measurements < 600 mA.

2. Connect the red test lead to the mA input.
on display.
10 A mA COM V.Ω.C
A
+ -
DC Current
Figure 64 - Connection for Low AC Current Measurement
116
WARNING:
Do not connect more than 600 mA AC current
across the mA input terminal or the protection
fuse will be tripped. Never input 10 A or more
current across the terminal or the instrument will
be damaged and warranty will be void.
Higher Current Measurements (Up to 10 A)
Follow these steps to make measurements up to 10 A.

2. Connect the red test lead to the 10A input.
on display.
10 A mA COM V.Ω.C
A
+ -
DC Current
Figure 65 - Connection for Higher AC Current Measurement
WARNING:
Do not connect more than 10 A DC current across
the 10A input terminal or the protection fuse will
be tripped.
117
4.3 Make Resistance Measurements
To measure resistances, press repeatedly until Meter is set to

“Res.”.
Table 45 – Resistance Measurement Menu

On
Display measurement in volts (V). In manual
V ranging, only the volts (V) ranges are
selectable.
Display measurement in millivolts (mV). In
mV manual ranging, only the millivolts (mV) ranges
are selectable.
Trend Plot

Resistance ranges: 600 Ω, 6 kΩ, 60 kΩ, 600 kΩ, 6 MΩ, and 60 MΩ.
118
CAUTION:

on display.
10 A mA COM V.Ω.C
Resistance
Figure 66 - Connection for Resistance Measurement
WARNING:
Do not apply more than 1000 VDC across the
terminals or they will be damaged.
119
4.4 Make Diode Measurements
The instrument can measure the forward voltage of general purpose
diodes.
To measure diodes, press repeatedly until Meter is set to Diode.
WARNING:
Fully discharge the capacitor before connecting it
to any of the inputs or it may damage the
instrument.
CAUTION:

on display.
120
10 A mA COM V.Ω.C
Diode
Figure 67 - Connection for Diode Measurement
WARNING:
4.5 Continuity Test

The instrument can test continuity.
Press repeatedly until Meter is set to Continuity.
Figure 68 - Continuity Test
121
WARNING:
instrument.
CAUTION:
To setup for continuity testing, do the following:

3. Connect the two leads together to verify that the continuity function
is working properly. The instrument should have a continuous beep
sound.
on display.
5. If continuity is good, it will have a continuous beep sound.
10 A mA COM V.Ω.C
Continuity
Figure 69 - Connection for Continuity Test
WARNING:
122
4.6 Make Capacitance Measurements
To measure capacitance, press repeatedly until Meter is set to

“Cap.”.
Figure 70 - Capacitance Measurement
Table 46 – Capacitance Measurement Menu

On

Trend Plot
Configure relative settings from the menu.
WARNING:
instrument.
123
CAUTION:
NOTE:
The capacitance measurement function is used for
measuring general purpose electrolytic capacitors.
Follow these steps to make a capacitance measurement.

4. Connect the black test lead to the COM input. This will connect to
the negative side of your capacitor.
5. Connect the red test lead to the V.Ω.C input. This will connect to
the positive side of your capacitor.
on display.
10 A mA COM V.Ω.C
Capacitor
Figure 71 - Connection for Capacitance Measurement
WARNING:
4.7 Using Trend Plot

The trend plot function is available for some of the multimeter
measurement functions. For details on using trend plot, refer to “Meter
Trend Plot” in the following chapter.
124
5 Using the Recorder
There are three categories under the recorder function: Scope Trend Plot,
Scope Recorder, and Meter Trend Plot.
The following sections will describe each of these functions in detail.
To enter the Recorder menu, press the button.
Scope Trend Plot

Scope Trend Plot allows storing two types of measurement data from the
oscilloscope’s channel input signals and plotting it to a graph. The data can
be stored into external memory using a USB flash drive connected to the
USB host port.
NOTE:
The oscilloscope cannot be in SCAN mode when
using scope trend plot. Before selecting the scope
trend plot function, check that the oscilloscope is
not in SCAN mode which will be indicated at the
top left of the display.
Scan mode is automatically enabled for timebase

set between 100 ms to 50 s.
NOTE:
When in scope trend plot mode, only the function
keys and the mode keys ( , ,
)are active.
125
From the Recorder menu, press to select Scope Trend Plot. The
scope trend plot screen and menu will be displayed.
Table 47 - Scope Trend Plot Menu 1/2

Clear current data plot and restart
Trend Plot Restart
recording.
Parameter Choose the parameter Voltage , time and delay
A/B to be measured. measurement
Run
Continue or Stop recording data.
Stop
Enter the second page of the
Next Page Page 1/2
Scope Trend Plot menu.
Table 48 - Scope Trend Plot Menu 2/2

Normal Display the data up to the minute.
View all Display all data on display.
Off Record data automatically
Manual Record data manually. Pressing
On
each time will record one measurement.
Select to save data to external USB flash
CSV CSV
drive.
Return Return Exit the Recorder mode.
Return to the first page of the Scope
Next Page Page 2/2
Trend Plot menu.
126
Record Data with Trend Plot
Follow these steps to record data using Scope Trend Plot.
1. Select the type of data you want to record.
Press to select Param A option, and a submenu similar to

the Measure menu will display.
2. Select between voltage, time, or delay measurement parameters.
Press to choose from voltage measurement parameters.

Press to choose from time measurement parameters.
Press to choose from delay measurement parameters.
3. Select the source channel and type of measurement parameter you

want to record.
For voltage measurement parameters, the menu and selections are
the same as in “Table 37 - Voltage Measurement Parameters Menu”.
For time measurement parameters, the menu and selections are the
same as in “Table 38 - Time Measurement Parameters Menu”.
For delay measurement parameters, the menu and selections are

the same as in “Table 39 - Delay Measurement Parameters Menu”.
4. After selecting, press to select Confirm. This will take you

back to the Scope Trend Plot menu. In the menu below Param A, it
will now show the new measurement parameter for recording.
If you are recording a different measurement parameter than what

was previously selected, a confirmation message will be displayed to
ask if you want to clear all data that are temporarily stored in
memory before recording the new measurement parameter. Press
127
to selection NO or press to select YES. Selecting
NO will cancel your changes and return to the Scope Trend Plot
menu.
NOTE:
If YES is selected, all data that has been recorded
previously will be deleted, including all data in
Param B.
5. Follow steps 1-4 to select the second measurement parameter to

record for Param B by pressing .
Pause Recording
By default, data is always recording continuously. To stop recording at any

time, press to toggle between Run or Stop.
Restart Recording
To restart recording the data from the beginning, press to select

Restart. The recording timer will reset back to 0:00:00 and all previously
recorded data will be cleared from memory.
Select Display Mode
The display settings on the trend plot can be changed. Users can select
viewing the data up to the minute, or select viewing all data in a
compressed format.
To toggle between the two display modes, go to the second page of the
Scope Trend Plot menu and press to toggle between Normal and
View All.
128
Record Data by Manual Trigger
By default, data is recorded automatically and continuously. To record data

by a manual trigger, access the second page of the Scope Trend Plot menu
and press to On or Off the Manual option.
When set to On, the plot will stop recording. Instead, the button
will function as a manual trigger button. Each subsequent press will trigger
one measurement recording to the plot (both Param A and Param B).
NOTE:
In this mode, the button will be used as a
trigger instead of a means to enter the Recorder
menu. To exit out of Scope Trend Plot, press
to select Return. All previously recorded
data will be lost if you exit. A confirmation
message will ask if you want to exit.
Save Recorded Data to External Memory
The recorded data on the scope trend plot is stored temporarily. All
recorded data will be lost if the recording gets reset, exit out of the scope
trend plot mode, or power OFF the instrument.
However, the data can be saved onto an external USB flash drive.
To save:
1. Go to the second page of the Scope Trend Plot menu and select
CSV by pressing .
2. The Directory menu will be displayed.
129
3. Follow the same instructions from section “3.7 Save/Recall
Function” to create a directory and/or a new file, then select Load
from the menu to save all recorded data into a new file on the
external USB flash drive.
NOTE:
Depending on the amount of data recorded, the
saving process may take a while. Please wait and
do not interrupt the instrument while it is saving
data. When finished, a message will prompt to
notify the file has been saved successfully.
To exit out of the Directory menu, go to the second page and select
Return.
Scope Recorder
The scope recorder allows users to record the oscilloscope’s channel input
signals for a long period of time. This function is available when the scope is
configured with slower timebase settings.
The recorded waveforms can be temporarily saved to and played back on

the instrument. It can also be saved into an external USB flash drive.
130
NOTE:
The Scope Recorder function is only available when
the oscilloscope is in SCAN mode. SCAN mode is
automatically enabled when the oscilloscope
timebase is set between 100 ms to 50 s.
Before entering the Scope Recorder menu, verify that the oscilloscope is
operating in SCAN mode. Press to enter the oscilloscope
operation mode and set SCAN mode. SCAN mode is available only for
timebase 100 ms to 50 s.
From the Recorder menu, press to select Scope Recorder. The

scope record screen and menu will be displayed.
Table 49 - Scope Recorder Menu

Record Select record options
Replay Replay the recorded waveform.
Option Setup the parameters of waveform recorder.
Return Exit scope recorder function.
Table 50 - Record Options Menu
Menu
Setting Description
Option
Start Begin recording CH1 and/or CH2 waveforms.
Replay Select to replay the recorded waveform.
131
Copy recording saved in internal memory to
Copy
Save Memory Copy recording to internal memory.
mode USB Key Copy recording to external USB.
Return Return to the Scope Recorder menu.
Table 51 - Replay Option Menu

Pause or continue to play the recorded waveform in
Stop/Continue memory. Timebase can be changed to view the
waveform in more detail.
Restart Replay the waveform
Previous View the previous section of the recorded waveform.
Next View the next section of the recorded waveform.
Table 52 - Option Menu
Menu
Setting Description
Option
Record and replay channel waveform with full
Full screen
screen.
Viewer Record and replay channel waveform with a
Split split screen. The top half will display CH1 and
the bottom half will display CH2.
Continuously record data. When memory is
continuous
Record full, the oldest data will be overwritten.
Single Stop recording data when memory is full.
When replaying, the screen waveform updates
Replay By Point
every dot from left to right.
132
When replaying, the screen waveform updates
By frame the whole screen according to the time of
sampling every frame of data.
Configure Record Options
Press from the Scope Recorder menu to select Options.
Press to set the Viewer for Full Screen or Split view. Then, set
Record to continuous or Single by pressing .
Start Scope Recording
To enable scope recording, press from the Scope Recorder menu

to select Record. Then, setup Save Mode to select where you want to store
the recording.
If USB key is selected for Save Mode, File Name will be shown in the menu
with a file name starting with BKXXXXX where XXXXX will be an auto
increment number starting with 00001. If no external USB flash drive is
detected, File Name will indicate No U disk.
Figure 72 - Scope Recorder External Save Mode
133
Press to select Start. The instrument will start scope recording.
Figure 73 - Recording Display
The top left will indicate the record time, which tracks the time length of
the recording. The remaining time is also indicated to track how much
longer the instrument can record before memory is full.
To stop recording at any time, press to select Stop.
To pause the recording at any time, press to select Pause. While

the recording is paused, the menu option will change to Continue.
Press it to continue recording.
Playback Scope Recording
To playback the recorded waveforms, from the Scope Recorder menu, press
to select Record. Then press to select Replay. The
waveform will begin to replay on the display.
Alternatively, you can go to the Replay menu by pressing from the

Scope Recorder menu, then press again to select Restart to begin
playback.
134
Figure 74 - Playback Scope Recording
To stop playback at any time, press to select Stop.
When the replay is finished, a message will say “This is the end of the
waveform”.
To view different portions of the recording, use the Previous and Next
menu options by pressing or respectively to go backward
or forward.
To replay it again after playback is finished, select Restart by pressing

.
To playback a file saved to an external USB flash drive, press from

the recorder menu to select File Name and the file directory screen will be
displayed. Select the file you want to playback by using the or
arrow, then press to select Load. You will then go back

to the Scope Recorder menu. Press to select Replay to playback
the selected file.
135
Meter Trend Plot
Meter Trend Plot allows storing of measurement data and plotting it into a
graph when in multimeter mode. The data can be stored into external
memory using a USB flash drive connected to the USB host port.
To enable this function, there are two ways.
1. Press the button from the front panel to enter the

multimeter mode. Then select Trend Plot by pressing .
2. Press the button and select Meter Trend Plot by pressing
.
NOTE:
The measurement function (i.e. DCV, ACV, Diode,
etc.) that the meter trend plot will store and plot
depends on the function configured within the
multimeter mode. Therefore, it is important to
set up the multimeter first with the measurement
function you want to use with trend plot.
By default, the trend plot will continuously store and plot data when you
enter the Meter Trend Plot menu.
136
1 2 3 4
Figure 75 - Meter Trend Plot Display
1
Recording/Trend Plot time and percentage of temporary storage
memory used.
2 Measured data value
3 Measurement function
4 Battery indicator
5 Range mode indicator
6 Measured data plot
7 Current measured value and time
Table 53 - Meter Trend Plot Menu 1/2
137
Menu
Setting Description
Option
Trend Plot Restart Restart the trend plot recording.
10Sa/s, 5Sa/s,
2Sa/s, 1Sa/s, Set the sampling rate of the trend plot
Sa Rate
0.5Sa/s, recording.
0.2Sa/s
Display the trend plot recorded data up to
Normal
the minute.
View All Display all trend plot recorded data.
Run Record data automatically.
Stop Stop recording data.
Enter the second page of the Meter Trend
Next Page Page1/2
Plot menu.
Table 54 - Meter Trend Plot Menu 2/2

Select to save recorded data onto
CSV
external USB flash memory.
Off Record data automatically.
Record data manually. Pressing
Manual
On each time will record one
measurement.
Instrument will return to the

Return
multimeter mode.
Return to the first page of the Meter
Next Page Page2/2
Trend Plot menu.
138
Record Data with Trend Plot
Follow these steps to record data using Meter Trend Plot.

1. Select the multimeter measurement function you want to record.
Press to enter the multimeter mode. Then configure the

multimeter for the function you want to measure (follow
instructions from chapter 4 “Using the Digital Multimeter”).
2. Select the sampling rate at which you want to record and plot the
measurement data.
Press to toggle the available sampling rate. 10 Sa/s is the

maximum and 0.2 Sa/s is the minimum rate.
Pause Recording
By default, data is always recording continuously. To stop recording at any

time, press to toggle between Run and Stop.
Restart Recording
To restart recording the data from the beginning, press to select

Restart. The recording timer will reset back to 0:00:00 and all previously
recorded data will be cleared from memory.
Select Display Mode
The display settings on the trend plot can be changed. Users can select
viewing the data up to the minute, or select viewing all data in a
compressed format.
To toggle between the two display modes, toggle to select

between Normal and View All.
139
Record Data by Manual Trigger
By default, data is recorded automatically and continuously. To record data

by a manual trigger, go to the second page of the Meter Trend Plot menu
and press to set the Manual option On or Off.
When set to On, the plot will stop recording. Instead, the button
will function as a manual trigger button. Each subsequent press will trigger
one measurement recording to the plot.
NOTE:
In this mode, the button will be used as a
trigger instead of entering the Recorder menu. To
exit out of Meter Trend Plot, press to
select Return in the second page of Meter Trend
Plot menu. All previously recorded data will be
lost if you exit. A confirmation message will ask if
you want to exit.
Save Recorded Data to External Memory
The recorded data on the meter trend plot is stored temporarily. All
recorded data will be lost if the recording gets reset, exit out of the meter
trend plot mode, or power OFF the instrument.
However, the data can be saved onto an external USB flash drive.
To save:
1. Go to the second page of the Meter Trend Plot menu and select CSV
by pressing .
2. The Directory menu will be displayed.
140
3. Follow the same instructions from section 3.7 “Save/Recall
Function” to create a directory and/or new file, then select Load
from the menu to save all recorded data into a new file on the
NOTE:
Depending on the amount of data recorded, the
saving process may take a while. Please wait and
do not interrupt the instrument while it’s saving.
When finished, a message will be displayed to
notify the file has been saved successfully.
To exit out of the Directory menu, go to the second page and select
Return.
141
6 Remote Communication
The 2510 series digital storage oscilloscope comes with application software
which provides most of the controls that emulate the front panel of the
instrument. The miniUSB device port on the side of the instrument, when
not used for probe compensation, can be used to connect to a computer
using a miniUSB to USB type A cable and allow remote communication via
the software.
The software is free and can be downloaded at www.bkprecision.com
Remote communication is supported using the software only. Remote

commands are not available.
142
7 Troubleshooting Guide
System Message Prompts and Instructions

 Trig level at limit!
The trigger level is at the limit when you adjust the trigger level.
 Horizon position at limit!
The horizontal position is at the limit when adjust the horizontal
position keys.
 Volts/Div at limit!
The vertical voltage scale has reached the Minimum 5mV/div or the
Maximum 100V/div.
 Volts position at limit!
The vertical position is at the limit when adjusting the vertical
position keys.
 Sec/Div at limit!
The Volts/Div is at maximum range while turning the vertical scale
keys.
 Holdoff time at limit!
The holdoff time is set to the maximum or minimum value.
 Function isn’t useable!
The selected function cannot be used with the current setup.
 No signal!
Signal could not be found using the key.
 Adjust at limit!
Pulse width has reached the limit (Min 20.0 ns or max 10.0 s).
 Location Empty!
If you have no stored waveforms or setups on the selected location,
the screen will display this information when you press the “Recall”
button on this location.
 USB Flash Drive Plug In!
A USB flash drive is detected and connected to the USB Host port.
 USB Flash Drive Pull Out!
A USB flash drive has been removed.
 Store Data Success!
143
File successfully saved.
 Ready Data Success!
Setup data or waveform data from the internal storage of the
oscilloscope or USB flash drive was read successfully.
 Record Wave Success!
This message will appear when you finish recording waveforms.
Frequency Asked Questions
Oscilloscope
1. I pressed the auto button, but it says no signal. Is it malfunctioning?
The auto function does not work for all waveforms. Usually,
waveforms that are periodic can be detected.
2. How do I adjust the trigger level?
The and keys are used to adjust trigger level.

However, if you select a menu option that has a symbol,
trigger level cannot be adjusted until you exit the menu or select a
different menu option that does not require the use of the same
keys as the trigger level adjust.
3. There is no Single button, how do I perform a single trigger capture?

Press to enter the Trigger menu, and set Mode to Single.
Then, use button to reset for each single capture.
4. How do I enter SCAN mode?

SCAN mode is available for timebase settings from 100 ms up to 50
s and is automatic. It is not available for timebase settings below
100 ms.
144
Multimeter
1. After I change a menu selection, how do I set the changes and close
the menu window?
Press the or keys to set the menu changes and to close

the menu window.
2. I cannot measure any current. Is there a problem?

There are 2 ports to measure current, one is labeled 10 A to
measure current up to 10 A. The other is labeled mA, which is
designed to only measure up to 600 mA. Both terminals have an
internal protection fuse. If you are not getting any measurements
from connecting to the correct port:
a. Check that there is current flowing from your DUT.
b. Your meter may not be in the correct range to make the
measurement. Change it to Auto range or change the range
manually to one suitable for the measurement.
c. Fuse may be blown for the 10 A input.
145
8 Specifications
Oscilloscope Specifications
All specifications apply to measurements with a 10X probe. To verify that
the oscilloscope meets specifications, the oscilloscope must first meet the
following conditions:
 The oscilloscope must have been operating continuously for 30
minutes within the specified operating temperature.
 If the operating temperature changes by more than 5° C, you must
perform the Do Self Cal operation, accessible through the Utility
menu.
All specifications are guaranteed unless noted “typical.”
Models 2511 2512 2515 2516

Bandwidth 60 MHz 100 MHz 60 MHz 100 MHz
Real Time (1)(2)
1 GSa/s (half-channel interleaved) , 500 MSa/s (per
Sampling Rate channel)
Channels 2 (non-isolated) 2 (isolated)
Rise Time < 5.8 ns < 3.5 ns < 5.8 ns < 3.5 ns
Ch to Ch
Isolation (Both
channels in > 100:1 at 50 MHz
same V/div
setting)
Memory Depth 40 kpts (half-channel interleaved)(1)(2), 20 kpts (per
channel)
Deep Memory(3) 2 Mpts (half-channel interleaved)(1), 1 Mpts (per channel)
Vertical
8 bits
Resolution
Vertical 2 mV/div – 100 V/div (1-2-5 5 mV/div – 100 V/div (1-2-5
Sensitivity order) order)
DC Gain ≤ ±4%
Accuracy
146
Max. BNC Input
CATII 300 V RMS from BNC signal to BNC shell
Voltage
Max. input (4)1x/10x CATII 300 V RMS (PR150SA)
Voltage for (5)(6)10x CATIII 600 V RMS, CATII 1000 V RMS (PR250SA)
probe
2mV - 200mV : ±1.6V 5mV - 200mV : ±1.6V
Channel Voltage
206mV - 10V : ±40V 206mV - 10V : ±40V
Offset Range
10.2V - 100V : ±400V 10.2V - 100V : ±400V
Bandwidth Limit 20MHz (-3dB)
Horizontal Scan 5.0nS/div - 2.5nS/div - 5.0nS/div - 2.5nS/div -
Range 50S/div 50S/div 50S/div 50S/div
Timebase
± 50 ppm measured over 1 ms interval
Accuracy
Input Coupling AC, DC, GND
Input 1 MΩ +/- 2 % || 18 pF ± 3 1 MΩ +/- 2 % || 16 pF ± 3
Impedance pF pF
Probe
Attenuation
1X, 5X, 10X, 50X, 100X, 500X, 1000X
Selectable
Factors
Vertical and
Vertically or horizontally expand or compress a live or
Horizontal
stopped waveform.
Zoom
I/O Interface
USB host port support USB flash drives (FAT format).
USB
USB device port for PC connectivity
Acquisition Modes
Sampling Display sample data only
Peak Detect Capture the maximum and minimum values of a signal
Waveform averaged, selectable from 4, 16, 32, 64, 128,
Average
256
Trigger System
Edge, Pulse Width, Video*, Slope, Alternative
Trigger Types *Support signal Formats: PAL/SECAM, NTSC

Trigger condition: odd field, even field, all lines, or line
number
Trigger Modes Auto, Normal, Single
Trigger Coupling AC, DC, LF reject, HF reject
147
Trigger Source CH1, CH2
Trigger Level
CH1, CH2: ± 6 divisions from center of display
Range
Trigger Pre-trigger: Memory depth/ 2* sampling
Displacement Delay Trigger: 268.04 div
Holdoff Range 100 ns – 1.5 s
Pulse Width Trigger Modes: Positive Pulse (>,<, ＝), Negative Pulse (>,
Trigger <, ＝)
Slope Trigger Positive slope (>, <, ＝), Negative slope (>, <, ＝)
Time: 20 ns - 10 s
Alternate CH1 trigger type: Edge, Pulse, Video, Slope
Trigger CH2 trigger type: Edge, Pulse, Video, Slope
Hardware Frequency Counter
Reading 1 Hz
Resolution
Range DC couple, 10 Hz to MAX bandwidth
Signal Types Satisfying all trigger signals (except pulse width trigger
and video trigger)
Waveform Math and Measure
Math Operation Add, Subtract, Multiply, Divide, FFT
FFT Window mode: Hanning, Hamming, Blackman,
Rectangular
Sampling points: 1024
Measure Vpp, Vmax, Vmin, Vamp, Vtop, Vbase, Vavg, Mean, Crms,
Vrms, ROVShoot, FOVShoot, RPREShoot, FPREShoot,
Rise, Fall, Freq, Prd, +Wid, -Wid, +Dut, -Dut, BWid, Phas,
FRR, FRF, FFR, FFF, LRR, LRF, LFR, LFF
Cursors
Types Voltage, Time
Measurements ΔV, ΔT, 1/ΔT (frequency)
Display System
Display 5.7” Color TFT, 320 x 234 resolution, 64K color
Display Contrast 150:1
(Typical)
Backlight 300 nits
Intensity
(Typical)
148
Wave Display 8 x 12 div
Range
Wave Display Dots, Vector
Mode
Persistence Off, 1 sec, 2 sec, 5 sec, Infinite
Menu Display 2 sec, 5 sec, 10 sec, 20 sec, Infinite
Screen-Saver Off, 1 min., 2 min., 5 min., 10 min., 15 min., 30 min., 1 hr,
2 hr, 5 hr
Waveform Sin(x)/x, Linear
Interpolation
Measure
Main, Window zoom, Scan, X-Y
Display Modes
X-Y Sampling Support 25 kSa/s - 250 MSa/s sampling rate (1-2.5-5
Frequency order)
Color Mode Normal, Invert
(1) Half channel operation means that only Ch1 or Ch2 is active.
(2) When sampling rate is 1 GSa/s. For sampling rate ≤ 500 MSa/s, the
maximum memory depth is 20 kpts.
(3) Available when sampling rate is < 500 MSa/s and maximum data depth
mode is enabled.
(4) Probe included with models 2511 and 2512 only.
(5) Probe included with models 2515 and 2516 only.
(6) Refer to the respective probe’s manual for more information on the
specification.
149
Maximum Input Voltages
Maximum Input Voltage vs. Frequency
The chart below shows the maximum input voltage vs. frequency.
150
Maximum Input Voltage between Scope Reference and Scope Reference
to ground
The chart below shows the maximum input voltage between scope
reference and scope reference to ground for models 2515 and 2516 only.
151
Multimeter Specifications
 All specifications are based on operating at temperatures 23 ± 5°C
and relative humidity < 75%.
 Accuracy is based on ± (% of reading + offset)
Display 6000 counts

Resolution
Measurement DC voltage, AC voltage, resistance, diode, continuity,
Function capacitance, DC current, AC current
Max. Input AC: 750 V (20 Hz - 1 kHz)

Voltage DC: 1000 V
Max. Input AC: 10 A (20 Hz - 1 kHz)
Current DC: 10 A
Input Impedance 10 MΩ
Max. Input
Voltage between CAT I, CAT II 600 V RMS
Multimeter input CAT III 300 V RMS
reference and
ground
Voltage/Resistance/Capacitance port: DC 1000 V, AC
Max. input
750 V RMS
Voltage for
Multimeter input Current port (mA): AC 250 V, 600 mA
ports Current port (10A): AC 250 V, 10 A
DC Voltage
Range Resolution Accuracy
60.00 mV 10 µV ± (1 % + 15 digit)
600.0 mV 100 µV
6.000 V 1 mV
60.00 V 10 mV ± (1 % + 5 digit)
600.0 V 100 mV
1000 V 1V
152
(1)ACVoltage
60.00 mV 10 µV ± (1 % + 15 digit)
600.0 mV 100 µV
6.000 V 1 mV
60.00 V 10 mV ± (1 % + 5 digit)
600.0 V 100 mV
750 V 1V
1. For frequency range 20 Hz to 1 kHz.
Resistance
600.0 Ω 0.1 Ω
6.000 kΩ 1Ω
60.00 kΩ 10 Ω
± (1 % + 5 digit)
600.0 kΩ 100 Ω
6.000 MΩ 1 kΩ
60.00 MΩ 10 kΩ
Diode and Continuity Measure

Diode 0–2V
Continuity < 50 Ω alarm
Capacitance
40.00 nF 10 pF ± (3 % + 10 digit) For > 5 nF
400.0 nF 100 pF
4.000 µF 1 nF
± (4 % + 5 digit)
40.00 µF 10 nF
400.0 µF 100 nF
153
(2)(3)DCand AC Current
60.00 mA 10 µA
± (1 % + 5 digit)
600.0 mA 100 µA
6.000 A 1 mA
± (1.5 % + 5 digit)
10.00 A 10 mA
2. For 10 A terminal, > 6 A DC or AC rms for 10 seconds ON and 15 minutes
OFF.
3. For AC current ranges, frequency is verified for 20 Hz to 1 kHz.
Recorder Specifications
Scope Trend Plot

Display Mode Full view, Normal
Record Length 800K points, > 24 hours
Number of
2
Channels
Multimeter Trend Plot

Record Length 1.2 M dots, > 24 hours
Number of Channels 1
Scope Recorder
Single Channel: 7M points
Max. Record Length
Dual Channel: 3.5 M points
Number of Channels 2
Maximum Record Size 4GB, 3000 hours
to External Storage
154
General Specifications
Environmental and Safety
Temperature Operating: 32 °F to 104 °F (0 °C to +40 °C)
Not operating: -4 °F to 158 °F (-20 °C to +70 °C)
Humidity Operating: 85% RH, 104 °F (40 °C), 24 hours
Altitude Operating: 9,842.5 ft (3,000 m)
Electromagnetic EMC Directive 2004/108/EC,
Compatibility EN61326:2006
Safety Low voltage directive 2006/95/EC, EN61010-1:2001
General
Storage 2 reference waveforms, 20 setups, 10 waveforms
Memory
AC adapter Input: 100-240 VAC, 50/60 Hz
Power Output: 9V DC, 4 A
Requirements
Battery 5000 mAh, 7.4 VDC
Charge Time Approx. 4 hrs
Dimensions (W 6.42” x 10.21” x 2.10” (163.2 x 259.5 x 53.3 mm)
x H x D)
Weight Approx. 3.4 lbs (1.54 kg) including battery
155
11 Maintenance
Do not expose the LCD display to direct sunlight for long periods of time.
To avoid damage to the instrument or probes, do not expose them to

sprays, liquids, or solvents.
Cleaning
If the instrument requires cleaning, disconnect it from all power sources
and clean only with a mild detergent and water. Be sure the instrument is
completely dry before reconnecting it to any power source.
To clean the exterior surface:

1. Remove loose dust on the outside of the instrument and probes
with a lint-free cloth.
2. Use a soft cloth dampened with water to clean the instrument.
Note: To avoid damaging the surface of the instrument and probes, do

not use any chemically abrasive cleaning agents.
156
SERVICE INFORMATION
Warranty Service: Please go the support and service section on our website www.bkprecision.com to
obtain an RMA #. Return the product in the original packaging with proof of purchase to the address
below. Clearly state on the RMA the performance problem and return any leads, probes, connectors
and accessories that you are using with the device.
Non-Warranty Service: Please go the support and service section on our website
www.bkprecision.com to obtain an RMA #. Return the product in the original packaging to the
address below. Clearly state on the RMA the performance problem and return any leads, probes,
connectors and accessories that you are using with the device. Customers not on an open account
must include payment in the form of a money order or credit card. For the most current repair
charges please refer to the service and support section on our website.
Return all merchandise to B&K Precision Corp. with pre-paid shipping. The flat-rate repair charge for
Non-Warranty Service does not include return shipping. Return shipping to locations in North
America is included for Warranty Service. For overnight shipments and non-North American shipping
fees please contact B&K Precision Corp.
B&K Precision Corp.

22820 Savi Ranch Parkway
Yorba Linda, CA 92887
www.bkprecision.com
714-921-9095
Include with the returned instrument your complete return shipping address, contact name, phone
number and description of problem.
LIMITED THREE-YEAR WARRANTY
B&K Precision Corp. warrants to the original purchaser that its products and the component parts
thereof, will be free from defects in workmanship and materials for a period of three years from date
of purchase.
B&K Precision Corp. will, without charge, repair or replace, at its option, defective product or
component parts. Returned product must be accompanied by proof of the purchase date in the form
of a sales receipt.
To help us better serve you, please complete the warranty registration for your new instrument via
our website www.bkprecision.com
Exclusions: This warranty does not apply in the event of misuse or abuse of the product or as a
result of unauthorized alterations or repairs. The warranty is void if the serial number is altered,
defaced or removed.
B&K Precision Corp. shall not be liable for any consequential damages, including without limitation
damages resulting from loss of use. Some states do not allow limitations of incidental or
consequential damages. So the above limitation or exclusion may not apply to you.
This warranty gives you specific rights and you may have other rights, which vary from state-to-state.
B&K Precision Corp.

www.bkprecision.com
714-921-9095
www.bkprecision.com
© 2013 B&K Precision Corp.
Printed in China V092017

BK PRECISION 251x - Manual

Uploaded by

Copyright:

Available Formats

BK PRECISION 251x - Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BK PRECISION 251x - Manual

Uploaded by

Copyright:

Available Formats

Model: 2511, 2512, 2515, 2516

2510 Series Handheld Digital

This manual contains information and warnings that must be followed to

 Do not connect the scope probes and DMM leads simultaneously.

To avoid potential fire or shock hazard:

This product is subject to Directive

Low Voltage Directive

Electrical Shock hazard.

Refer to the operating user manual for warning information to

This symbol shows that the switch is a power switch located at

CATI Category I overvoltage conditions.

Maximum Input Voltages

Maximum Floating Voltage

The following applies to all models:

 Maximum floating voltage from multimeter reference to earth

Figure 1 - Front Panel View ........................................................................... 18

1.1 Product Overview

 1 x 2510 series handheld digital storage oscilloscope

Figure 1 - Front Panel View

Front Panel Description

8 Channel 1 Volts/div range keys (scope)

10 Channel 1 vertical position keys (scope)

11 10 A current input port (multimeter)

16 Channel 2 vertical position keys (scope)

17 Horizontal position keys (scope)

18 Channel 2 Volts/div range keys (scope)

19 Horizontal Timebase keys (scope)

24 Arrow selection keys

25 Auto button (scope)

1.4 Top View

Channel 1 Input Channel 2 Input

Figure 2 - Top View

1.5 Rear Panel Overview

Figure 3 - Rear View

Figure 4 - Side View

Side Panel Description

Figure 6 - Multimeter Display

Input port indicator

Figure 7 – Scope Trend Plot Display

1 Recording/Trend Plot time

The 10 A input is protected with an internal 10 A, 250 V slow blow glass

The mA input is protected with an internal 600 mA PPTC (resettable) type

1.9 Isolation (Model 2515/2516)

Oscilloscope Probe Input BNC

Input Signal Input Signal

Float Voltage Float Voltage

CATII 1000V CATII 1000V

Voltage Rating: 1000 V CATII, 600V CATIII

Voltage Rating: 300 V CATII

2.1 Input Power Requirements

External Power Operation

To use the external AC adapter to power the instrument:

Figure 8 - Connecting Power Adapter

Installing the Battery

Figure 9 - Installing Battery

2.2 Tilt Stand

2.3 Power On Device

Power ON the device by pressing once.

Figure 10 - Boot Screen