Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

LM 2445

Download as pdf or txt
Download as pdf or txt
You are on page 1of 14

LM2445 Monolithic Triple 7.

5 ns CRT Driver
March 2003

LM2445
Monolithic Triple 7.5 ns CRT Driver
General Description Features
The LM2445 is an integrated high voltage CRT driver circuit n Higher gain to match LM126X CMOS preamplifiers
designed for use in color monitor applications. The IC con- n 0V to 3.75V input range
tains three high input impedance, wide band amplifiers n Stable with 0–20 pF capacitive loads and inductive
which directly drive the RGB cathodes of a CRT. Each peaking networks
channel has its gain internally set to −20 and can drive CRT n Convenient TO-220 staggered lead package style
capacitive loads as well as resistive loads present in other n Maintains standard LM243X Family pinout which is
applications, limited only by the package’s power dissipation. designed for easy PCB layout
The IC is packaged in an industry standard 9-lead TO-220
molded plastic power package. See the Thermal Consider- Applications
ations section for more information.
n 1024 x 768 displays up to 85 Hz refresh
n Pixel clock frequencies up to 95 MHz
n Monitors using video blanking

Schematic Diagram

20063701

FIGURE 1. Simplified Schematic Diagram


(One Channel)

© 2003 National Semiconductor Corporation DS200637 www.national.com


LM2445
Connection Diagram

20063702
Note: Tab is at GND
Top View
Order Number LM2445TA

www.national.com 2
LM2445
Absolute Maximum Ratings (Notes 1, Machine Model 250V
3)
If Military/Aerospace specified devices are required, Operating Ranges (Note 2)
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications. VCC +60V to +85V
VBB +8V to +15V
Supply Voltage (VCC) +90V
VIN +0V to +3.75V
Bias Voltage (VBB) +16V
VOUT +15V to +75V
Input Voltage (VIN) 0V to 4.5V
Case Temperature −20˚C to +100˚C
Storage Temperature Range (TSTG) −65˚C to +150˚C
Do not operate the part without a heat sink.
Lead Temperature
(Soldering, < 10 sec.) 300˚C
ESD Tolerance, Human Body
2 kV
Model

Electrical Characteristics
(See Figure 2 for Test Circuit) Unless otherwise noted: VCC = +80V, VBB = +12V, CL = 8 pF, TC = 50˚C DC Tests: VIN =
2.25VDC AC Tests: Output = 40VPP(25V - 65V) at 1MHz
LM2445
Symbol Parameter Conditions Units
Min Typical Max
ICC Supply Current All Three Channels, No Input Signal,
30 mA
No Output Load
IBB Bias Current All Three Channels 18 mA
VOUT DC Output Voltage No AC Input Signal, VIN = 1.25V 62 65 68 VDC
AV DC Voltage Gain No AC Input Signal −18 −20 −22
∆AV Gain Matching (Note 4), No AC Input Signal 1.0 dB
LE Linearity Error (Notes 4, 5), No AC Input Signal 5 %
tR Rise Time (Note 6), 10% to 90% 7.5 ns
tF Fall Time (Note 6), 90% to 10% 8 ns
OS Overshoot (Note 6) 1 %

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
Note 2: Operating ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and
test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may
change when the device is not operated under the listed test conditions.
Note 3: All voltages are measured with respect to GND, unless otherwise specified.
Note 4: Calculated value from Voltage Gain test on each channel.
Note 5: Linearity Error is the variation in dc gain from VIN = 1.0V to VIN = 3.5V.
Note 6: Input from signal generator: tr, tf < 1 ns.

3 www.national.com
LM2445
AC Test Circuit

20063703
Note: 8 pF load includes parasitic capacitance.

FIGURE 2. Test Circuit (One Channel)

Figure 2 shows a typical test circuit for evaluation of the LM2445. This circuit is designed to allow testing of the LM2445 in a 50Ω
environment without the use of an expensive FET probe. The two 2490Ω resistors form a 200:1 divider with the 50Ω resistor and
the oscilloscope. A test point is included for easy use of an oscilloscope probe. The compensation capacitor is used to
compensate the stray capacitance of the two 2490Ω resistors to achieve flat frequency response.

www.national.com 4
LM2445
Typical Performance Characteristics (VCC = +80 VDC, VBB = +12 VDC, CL = 8 pF, VOUT = 40 VPP
(25V−65V), Test Circuit - Figure 2 unless otherwise specified)

20063704 20063707

FIGURE 3. VOUT vs VIN FIGURE 6. Power Dissipation vs Frequency

20063705 20063708

FIGURE 4. Speed vs Temp. FIGURE 7. Speed vs Offset

20063706

20063709
FIGURE 5. LM2445 Pulse Response
FIGURE 8. Speed vs Load Capacitance

5 www.national.com
LM2445
Theory of Operation performance and to protect against damage from CRT ar-
cover are designed specifically for the LM2445. If another
The LM2445 is a high voltage monolithic three channel CRT member of the LM246X family is used, please refer to its
driver suitable for high resolution display applications. The datasheet.
LM2445 operates with 80V and 12V power supplies. The
part is housed in the industry standard 9-lead TO-220 POWER SUPPLY BYPASS
molded plastic power package.
Since the LM2445 is a wide bandwidth amplifier, proper
The circuit diagram of the LM2445 is shown in Figure 1. The power supply bypassing is critical for optimum performance.
PNP emitter follower, Q5, provides input buffering. Q1 and Improper power supply bypassing can result in large over-
Q2 form a fixed gain cascode amplifier with resistors R1 and shoot, ringing or oscillation. 0.1 µF capacitors should be
R2 setting the gain at −20. Emitter followers Q3 and Q4 connected from the supply pins, VCC and VBB, to ground, as
isolate the high output impedance of the cascode stage from close to the LM2445 as is practical. Additionally, a 47 µF or
the capacitance of the CRT cathode which decreases the larger electrolytic capacitor should be connected from both
sensitivity of the device to load capacitance. Q6 provides supply pins to ground reasonably close to the LM2445.
biasing to the output emitter follower stage to reduce cross-
over distortion at low signal levels. ARC PROTECTION
Figure 2 shows a typical test circuit for evaluation of the During normal CRT operation, internal arcing may occasion-
LM2445. This circuit is designed to allow testing of the ally occur. Spark gaps, in the range of 200V, connected from
LM2445 in a 50Ω environment without the use of an expen- the CRT cathodes to CRT ground will limit the maximum
sive FET probe. In this test circuit, the two 2.49kΩ resistors voltage, but to a value that is much higher than allowable on
form a 200:1 wideband, low capacitance probe when con- the LM2445. This fast, high voltage, high energy pulse can
nected to a 50Ω coaxial cable and a 50Ω load (such as a damage the LM2445 output stage. The application circuit
50Ω oscilloscope input). The input signal from the generator shown in Figure 9 is designed to help clamp the voltage at
is ac coupled to the base of Q5. the output of the LM2445 to a safe level. The clamp diodes,
D1 and D2, should have a fast transient response, high peak
Application Hints current rating, low series impedance and low shunt capaci-
tance. FDH400 or equivalent diodes are recommended. Do
INTRODUCTION not use 1N4148 diodes for the clamp diodes. D1 and D2
National Semiconductor (NSC) is committed to provide ap- should have short, low impedance connections to VCC and
ground respectively. The cathode of D1 should be located
plication information that assists our customers in obtaining
very close to a separately decoupled bypass capacitor (C3 in
the best performance possible from our products. The fol-
Figure 9). The ground connection of D2 and the decoupling
lowing information is provided in order to support this com-
capacitor should be very close to the LM2445 ground. This
mitment. The reader should be aware that the optimization of
will significantly reduce the high frequency voltage transients
performance was done using a specific printed circuit board
that the LM2445 would be subjected to during an arcover
designed at NSC. Variations in performance can be realized
condition. Resistor R2 limits the arcover current that is seen
due to physical changes in the printed circuit board and the
by the diodes while R1 limits the current into the LM2445 as
application. Therefore, the designer should know that com-
well as the voltage stress at the outputs of the device. R2
ponent value changes may be required in order to optimize
should be a 1⁄2W solid carbon type resistor. R1 can be a 1⁄4W
performance in a given application. The values shown in this
metal or carbon film type resistor. Having large value resis-
document can be used as a starting point for evaluation
tors for R1 and R2 would be desirable, but this has the effect
purposes. When working with high bandwidth circuits, good
of increasing rise and fall times. Inductor L1 is critical to
layout practices are also critical to achieving maximum per-
reduce the initial high frequency voltage levels that the
formance.
LM2445 would be subjected to. The inductor will not only
IMPORTANT INFORMATION help protect the device but it will also help minimize rise and
fall times as well as minimize EMI. For proper arc protection,
The LM2445 performance is targeted for the VGA (640 x it is important to not omit any of the arc protection compo-
480) to XGA (1024 x 768, 85 Hz refresh) resolution market. nents shown in Figure 9.
The application circuits shown in this document to optimize

www.national.com 6
LM2445
Application Hints (Continued)

20063710

FIGURE 9. One Channel of the LM2445 with the Recommended Application Circuit

OPTIMIZING TRANSIENT RESPONSE this case). This graph gives the designer the information
Referring to Figure 9, there are three components (R1, R2 needed to determine the heat sink requirement for his appli-
and L1) that can be adjusted to optimize the transient re- cation. The designer should note that if the load capacitance
sponse of the application circuit. Increasing the values of R1 is increased the AC component of the total power dissipation
and R2 will slow the circuit down while decreasing over- will also increase.
shoot. Increasing the value of L1 will speed up the circuit as The LM2445 case temperature must be maintained below
well as increase overshoot. It is very important to use induc- 100˚C. If the maximum expected ambient temperature inside
tors with very high self-resonant frequencies, preferably the monitor is 70˚C and the power dissipation is 4.4W (from
above 300 MHz. Ferrite core inductors from J.W. Miller Figure 6, 50 MHz max. video frequency), then a maximum
Magnetics (part # 78FR--k) were used for optimizing the heat sink thermal resistance can be calculated:
performance of the device in the NSC application board. The
values shown in Figure 11 and Figure 12 can be used as a
good starting point for the evaluation of the LM2445. Using
variable resistors for R1 and the parallel resistor will simplify
finding the values needed for optimum performance in a This example assumes a capacitive load of 8 pF and no
given application. Once the optimum values are determined resistive load.
the variable resistors can be replaced with fixed values.
TYPICAL APPLICATION
EFFECT OF LOAD CAPACITANCE
A typical application of the LM2445 is shown in Figure 11 and
Figure 8 shows the effect of increased load capacitance on Figure 12. Used in conjunction with an LM1267, a complete
the speed of the device. This demonstrates the importance video channel from monitor input to CRT cathode can be
of knowing the load capacitance in the application. achieved. Performance is ideal for 1024 x 768 resolution
displays with pixel clock frequencies up to 95 MHz. Figure 11
EFFECT OF OFFSET and Figure 12 are the schematic for the NSC demonstration
Figure 7 shows the variation in rise and fall times when the board that can be used to evaluate the LM1267/2466 com-
output offset of the device is varied from 40 to 50 VDC. The bination in a monitor, and Figure 10 shows the typical re-
rise time shows a maximum variation relative to the center sponse at the red cathode for this application. The input
data point (45 VDC) less than 5%. The fall time shows a video rise time is 3.2ns, and the peaking component values
variation of less than 8% relative to the center data point. are those recommended in Figure 12. Table 1 shows the
typical cathode response of all three channels.
THERMAL CONSIDERATIONS
Figure 4 shows the performance of the LM2445 in the test
circuit shown in Figure 2 as a function of case temperature.
The figure shows that the rise time of the LM2445 increases
by approximately 10% as the case temperature increases
from 50˚C to 100˚C. This corresponds to a speed degrada-
tion of 2% for every 10˚C rise in case temperature. The fall
time increases by approximately 7% as the case tempera-
ture increases from 50˚C to 100˚C.
Figure 6 shows the maximum power dissipation of the
LM2445 vs. Frequency when all three channels of the device
are driving an 8 pF load with a 40 Vp-p alternating one pixel
on, one pixel off signal. The graph assumes a 72% active
time (device operating at the specified frequency) which is
typical in a monitor application. The other 28% of the time
the device is assumed to be sitting at the black level (65V in

7 www.national.com
LM2445
Application Hints (Continued) Because of its high small signal bandwidth, the part may
oscillate in a monitor if feedback occurs around the video
channel through the chassis wiring. To prevent this, leads to
the video amplifier input circuit should be shielded, and input
circuit wiring should be spaced as far as possible from output
circuit wiring.

NSC DEMONSTRATION BOARD


Figure 13 shows the routing and component placement on
the NSC LM1267/2466 demonstration board. The schematic
of the board is shown in Figure 11 and Figure 12. This board
provides a good example of a layout that can be used as a
guide for future layouts. Note the location of the following
components:
• C19 — VCC bypass capacitor, located very close to pin 4
and ground pins
20063716 • C20 — VBB bypass capacitors, located close to pin 8 and
ground
FIGURE 10. Red Cathode Response • C46, C47, C48 — VCC bypass capacitors, near LM2445
and VCC clamp diodes. Very important for arc protection.
The routing of the LM2445 outputs to the CRT is very critical
TABLE 1. LM2445 Cathode Response to achieving optimum performance. Figure 14 shows the
routing and component placement from pin 1 of the LM2445
Channel tr/OS tf/OS to the blue cathode. Note that the components are placed so
Red 6.3ns / 7% 6.3ns / 3% that they almost line up from the output pin of the LM2445 to
Green 6.1ns / 6% 5.9ns / 4% the blue cathode pin of the CRT connector. This is done to
minimize the length of the video path between these two
Blue 6.5ns / 3% 6.4ns / 2%
components. Note also that D8, D9, R24 and D6 are placed
to minimize the size of the video nodes that they are at-
PC BOARD LAYOUT CONSIDERATIONS tached to. This minimizes parasitic capacitance in the video
For optimum performance, an adequate ground plane, iso- path and also enhances the effectiveness of the protection
lation between channels, good supply bypassing and mini- diodes. The anode of protection diode D8 is connected
mizing unwanted feedback are necessary. Also, the length of directly to a section of the the ground plane that has a short
the signal traces from the preamplifier to the LM2445 and and direct path to the LM2445 ground pins. The cathode of
from the LM2445 to the CRT cathode should be as short as D9 is connected to VCC very close to decoupling capacitor
possible. The following references are recommended: C19 (see Figure 14) which is connected to the same section
of the ground plane as D8. The diode placement and routing
Ott, Henry W., “Noise Reduction Techniques in Electronic
is very important for minimizing the voltage stress on the
Systems”, John Wiley & Sons, New York, 1976.
LM2445 during an arcover event. Lastly, notice that S3 is
“Video Amplifier Design for Computer Monitors”, National placed very close to the blue cathode and is tied directly to
Semiconductor Application Note 1013. CRT ground.
Pease, Robert A., “Troubleshooting Analog Circuits”,
Butterworth-Heinemann, 1991.

www.national.com 8
Application Hints (Continued)

9
20063717

FIGURE 11. LM126X/LM246X Demonstration Board Schematic

www.national.com
LM2445
LM2445

Application Hints (Continued)

www.national.com
10
20063718

FIGURE 12. LM126X/LM246X Demonstration Board Schematic (continued)


LM2445
Application Hints (Continued)

20063719

FIGURE 13. LM126X/LM246X Demo Board Layout

11 www.national.com
LM2445
Application Hints (Continued)

20063714

FIGURE 14. Trace Routing and Component Placement for Blue Channel Output

www.national.com 12
LM2445
Physical Dimensions inches (millimeters)
unless otherwise noted

CONTROLLING DIMENSION IS INCH


VALUES IN [ ] ARE MILLIMETERS
NS Package Number TA09A
Order Number LM2445TA

13 www.national.com
LM2445 Monolithic Triple 7.5 ns CRT Driver
Notes

LIFE SUPPORT POLICY


NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or 2. A critical component is any component of a life
systems which, (a) are intended for surgical implant support device or system whose failure to perform
into the body, or (b) support or sustain life, and can be reasonably expected to cause the failure of
whose failure to perform when properly used in the life support device or system, or to affect its
accordance with instructions for use provided in the safety or effectiveness.
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor National Semiconductor National Semiconductor National Semiconductor
Americas Customer Europe Customer Support Center Asia Pacific Customer Japan Customer Support Center
Support Center Fax: +49 (0) 180-530 85 86 Support Center Fax: 81-3-5639-7507
Email: new.feedback@nsc.com Email: europe.support@nsc.com Fax: +65-6250 4466 Email: jpn.feedback@nsc.com
Tel: 1-800-272-9959 Deutsch Tel: +49 (0) 69 9508 6208 Email: ap.support@nsc.com Tel: 81-3-5639-7560
English Tel: +44 (0) 870 24 0 2171 Tel: +65-6254 4466
www.national.com Français Tel: +33 (0) 1 41 91 8790

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.

You might also like