Setting Integration Tool Manual

Xiamen Rongta Technology Co., Ltd.
Instructions of Setting Integration Tool
It is a collection of thermal printer’s setting functions, including setting serial port,

Ethernet port, language and program update ect. It’s powerful and easy to use.
I. Connect the Printer
Double-click the tool “PrinterTool.exe”, and then it’ll show as below:
As shown above, there are three ways to connect to the printer.

1. Connect the printer via USB
Please click USB option if the printer is connected by USB port. Then you can
proceed to “set printer” or “download”. (You can click USB option if the printer is
connected by USB port. Or the option is gray and can’t be chosen. )
2. Connect the printer via port
www.rongtatech.com 1
Connect the printer after “Config Port” via serial port, Ethernet port or parallel
port, then proceed to “set printer” or “download”.
a. Setup port if choose serial port.
b. Setup IP if choose Ethernet port, then connect the printer.
c. Choose parallel
3. Connect printer via common driver (You need to choose and setup corresponding
Port of the driver), then proceed to “set printer” or “download”.
II. “Download” function in the main interface.

Click “download”, then it’ll show as below
1. Update program. Click “open files”, select path of corresponding firmware, click
“update”, and then update program.
2. It’s available to add a picture. Select “logo”, clicks “add”, chooses corresponding
path, then add a logo to the printer.
Note: In this tool, the logo only supports BMP format images (black and white bitmap,
or 32-bit panchromatic bitmap) and other image format does not support.
Supported by the bitmap size has certain requirements, the specific requirements
are as follows:
1. Picture size should be less than 64K
2. The width of the picture:
80 the width of the pixel size is less than 567.
58 the width of the pixel size is less than 387.
III. Main platform “Set Printer” function
When click the “Set Printer” of the main platform, then it will show as below:
There are 10 platforms.
3.1 “Basic setting”

User can set the printer codepage, baud rate, character, density, cash draw and
cutter, and precede the update by printing Self Test page.
Note: if uesr choose serial interface for printing, the user need to be back to the
main platform to reconfigurate the baud rate for printing self test page.
3.2 “Ethernet”
1. Set the IP address of the printer, change to "192.168.1.87", and set up the
communication port.
2. Set the subnet mask of the printer, change to "255.255.255.0.
3. Set the printer gateway to "192.168.1.1".
4. Set the printer function of DHCP, the DHCP default printer is closed, if you
need to open, let the printer automatically obtain an IP address.
5. Set the MAC address, and the network transmission rate of setting.
Note: If the printer connection is either “Ethernet” or “IP of printer drivers”

before setting website, the IP is changed. At that time, the printer and the tool
has been disconnected. Resetting IP of the tool is needed for the connection.
Other connection ways are unaffected.
3.3 “WIFI”
If the printer is equipped with Wifi function, setting Wifi technical parameter is
required.
A. Input the SSID (Wifi name) and the relative pattern.
B. Input the Wifi encryption type and Wifi PSK key. E.g.： edit the data as
following SSID: rdhz, encryption type: WPA-PSK, and input the PSK key.
Click “SET”.
C. After clicking “SET”，the printer will print the set Wifi parameter. Please print
self test page to check the parameter with Router’s. If it is correct, please be
patient for connection between the printer and Wifi within one minute. If not,
repeat the above steps for resetting parameter.
3.4 “Black mark” 1

2
1.Click “Enable” to open black mark, printer will alarm one “di” if successful.
2.After that, please turn off printer, and turn on, only that, you can set black mark
parameters.
3.Set printing position, for example, input 10mm, printer will print in 10mm position
after black mark. After input, click “set”, printer will alarm one “di” if successful.
4.Set black mark width，longer than real black mark width, if the real is 10mm, you
can set 20mm. After input, click “set”, printer don’t alarm if successful.
5.Set black mark length，the distance between two black marks，longer than real black
mark length. If the real is 200mm, you can set 400mm. After input, click “set”, printer
will alarm one “di” if successful.
6.Set cutting position, for example, input 10mm, printer will cut in 10mm position
after black mark. After input, click “set”, printer will alarm one “di” if successful.
3.5 “Portable” printer baud rate, density ect.
3.6 Mechanism heating time

Input the heating time what you need, and then click “set”. After setting, printing
out the self test page, to check if the heating time is the same to the time you set.
3.7 “QR CODE”

This is a function which can set “allow not allow printing our QR code”, after
setting, printing out the self test page to check if the printer can print out the QR code.
3.8 “Serial port settings”
Notice：After serial port setting, the parameter is changed. You need to go back
to main page to reset the parameter.
3.9 Search Printer

a. Connected internet cable, select network port, set IP addresses corresponding.
Select “search printer” success find the printer, will show MAC address, IP
address corresponding, select printer, and then execute related configuration or
operation.
3.10 BIG5 (only used for Traditional Chinese language printing at

Taiwan)

Setting Integration Tool Manual

Uploaded by

Copyright:

Available Formats

Setting Integration Tool Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Setting Integration Tool Manual

Uploaded by

Copyright:

Available Formats

Xiamen Rongta Technology Co., Ltd.

Instructions of Setting Integration Tool

It is a collection of thermal printer’s setting functions, including setting serial port,

As shown above, there are three ways to connect to the printer.

b. Setup IP if choose Ethernet port, then connect the printer.

II. “Download” function in the main interface.

III. Main platform “Set Printer” function

There are 10 platforms.

3.1 “Basic setting”

Note: If the printer connection is either “Ethernet” or “IP of printer drivers”

3.4 “Black mark” 1

3.5 “Portable” printer baud rate, density ect.

3.6 Mechanism heating time

3.7 “QR CODE”

3.8 “Serial port settings”

3.9 Search Printer

3.10 BIG5 (only used for Traditional Chinese language printing at

You might also like