1N5333----1N5388

ZENER DIODES
PEAK PULSE POWER: 5 WATTS

FEATURES
· Silicon planar power zener diodes DO-15
· For use in stabilizing and clipping curcuits with
high
power rating.
· Standard zener voltage tolerance is ±10%. Add
suffix "B" for ±5% tolerance. other zener voltage
and tolerances are available upon request.

MECHANICAL DATA
Case:DO-201AE
Terminals: solderable per MIL-STD-202, method 208
Polarity: cathode Band
Marking: type number Dimensions in inches and (millimeters)
Approx. weight: 0.032 ounces, 0.9 grams

Maximum Ratings and Electrical Characteristics

Ratings at 25℃ ambient temperature unless otherwise specified.
Single phase,half wave,60 Hz,resistive or inductive load. For capacitive load,derate by 20%.

Symbols VALUE Units

Zener current (see Table "Characteristics")
DC power dissipation @ TL=75, measure at zero lead length (Fig.1) 5.0 W
PD
derate above 75 (NOTE 1) 40.0 mW
Peak forward surge current 8.3ms single half sine-wave superimposed on
IFSM see fig.5 A
rated load (JEDEC Method)(NOTE 1,2)

Junction temperature TJ -55----150 ℃

Storage temperature range TS -55----170 ℃

NOTES:
1- Mounted on 8.0mm2 copper pads to each terminal.
2- 8.3ms single half sine-wave, or equivalent square wave, duty cycle=4 pulses per minute maximum.
1N5333----1N5388
ZENER DIODES
ELECTRICAL CHARACTERISTICS (TA=25 ℃ )

Maximum Zener
Zener voltage Max Reverse Leakage
Impedance
(Note 2) Current IR VZ IZM
(Note 2)
Type (Note 1) (Note 3) (Note 4) (Note 5)
ZZT@IZK =1μ IR VR A V mA
VZ@IZT IZT ZZT@IZT
A mA
V mA Ω
Ω uA V

1N5333 3.3 380 3 400 300 1.0 20 0.85 1440

1N5334 3.6 350 2.5 500 150 1.0 18.7 0.8 1320
1N5335 3.9 320 2 500 50 1.0 17.6 0.54 1220
1N5336 4.3 290 2 500 10 1.0 16.4 0.49 1100
1N5337 4.7 260 2 450 5 1.0 15.3 0.44 1010
1N5338 5.1 240 1.5 400 1 1.0 14.4 0.39 930
1N5339 5.6 220 1 400 1 2 13.4 0.25 865
1N5340 6 200 1 300 1 3 12.7 0.19 790
1N5341 6.2 200 1 200 1 4 12.4 0.1 765
1N5342 6.8 175 1 200 10 4.9 11.5 0.15 700
1N5343 7.5 175 1.5 200 10 5.4 10.7 0.15 630
1N5344 8.2 150 1.5 200 10 5.9 10 0.2 580
1N5345 8.7 150 2 200 10 6.3 9.5 0.2 545
1N5346 9.1 150 2 150 7.5 6.6 9.2 0.22 520
1N5347 10 125 2 125 5 7.2 8.6 0.22 475
1N5348 11 125 2.5 125 5 8 8 0.25 430
1N5349 12 100 2.5 125 2 8.6 7.5 0.25 395
1N5350 13 100 2.5 100 1 9.4 7 0.25 365
1N5351 14 100 2.5 75 1 10.1 6.7 0.25 340
1N5352 15 75 2.5 75 1 10.8 6.3 0.25 315
1N5353 16 75 2.5 75 1 11.5 6 0.3 295
1N5354 17 70 2.5 75 0.5 12.2 5.8 0.35 280
1N5355 18 65 2.5 75 0.5 13 5.5 0.4 264
1N5356 19 65 3 75 0.5 13.7 5.3 0.4 250
1N5357 20 65 3 75 0.5 14.4 5.1 0.4 237
1N5358 22 50 3.5 75 0.5 15.8 4.7 0.45 216
1N5359 24 50 3.5 100 0.5 17.3 4.4 0.55 198
1N5360 25 50 4 110 0.5 18 4.3 0.55 190
1N5361 27 50 5 120 0.5 19.4 4.1 0.6 176
1N5362 28 50 6 130 0.5 21.1 3.9 0.6 170
1N5363 30 40 8 140 0.5 21.6 3.7 0.6 158
1N5364 33 40 10 150 0.5 23.8 3.5 0.6 144
1N5365 36 30 11 160 0.5 25.9 3.5 0.65 132
1N5366 39 30 14 170 0.5 28.1 3.1 0.65 122
1N5367 43 30 20 190 0.5 31 2.8 0.7 110
1N5368 47 25 25 210 0.5 33.8 2.7 0.8 100
1N5369 51 25 27 230 0.5 36.7 2.5 0.9 93
1N5370 56 20 35 280 0.5 40.3 2.3 1 86
1N5371 60 20 40 350 0.5 43 2.2 1.2 79
1N5372 62 20 42 400 0.5 44.6 2.1 1.35 76
1N5373 68 20 44 500 0.5 49 2 1.5 70
1N5374 75 20 45 620 0.5 54 1.9 1.6 63
1N5375 82 15 65 720 0.5 59 1.8 1.8 58
1N5376 87 15 75 760 0.5 63 1.7 2 54.5
1N5377 91 15 75 760 0.5 65.5 1.6 2.2 52.5
1N5378 100 12 90 800 0.5 72 1.5 2.5 47.5
1N5379 110 12 125 1000 0.5 79.2 1.4 2.5 43
1N5380 120 10 170 1150 0.5 86.4 1.3 2.5 39.5
1N5381 130 10 190 1250 0.5 93.2 1.2 2.5 36.6
1N5382 140 8 230 1500 0.5 101 1.2 2.5 34
1N5383 150 8 330 1500 0.5 108 1.1 3 31.6
1N5384 160 8 350 1650 0.5 115 1.1 3 29.4
1N5333----1N5388
ZENER DIODES

ELECTRICAL CHARACTERISTICS (TA=25 ℃ )

Maximum Zener
Zener voltage Max Reverse Leakage
Impedance
(Note 2) Current IR VZ IZM
(Note 2)
Type (Note 1) (Note 3) (Note 4) (Note 5)
ZZT@IZK =1μ IR VR A V mA
VZ@IZT IZT ZZT@IZT
A mA
V mA Ω
Ω uA V

1N5385 170 8 380 1750 0.5 122 1 3 28

1N5386 180 5 430 1750 0.5 130 1 4 26.4
1N5387 190 5 450 1850 0.5 137 0.9 5 25
1N5388 200 5 480 1850 0.5 144 0.9 5 23.6

Note:
1 TOLERANCE AND VOLTAGE DESIGNATION-The JEDEC type numbers shown indicate a tolerance of ±10% with guaranteed
limits on only Vz, IR, Ir, and VF as shown in the electrical characteristics table. Units with guaranteed limits
on all seven parameters are indicated by suffix "B" for ±5% tolerance.

2 ZENER VOLTAGE (Vz) AND IMPEDANCE (ZZT & ZZK) - Test conditions for zener voltage and impedance are as follows;Iz
is applied 40±10ms prior to reading. Mounting contacts are located from the inside edge of mounting clips to the
body of the diode.

3 SURGE CURRENT (Ir) - Surge current is specified as the maximum allowable peak, non-recurrent square-wave current
with a pulse width, PW, of 8.3ms.The data given in Fig 5. May be used to find the maximum surge current for a
quare wave of any pulse width between 1 ms by plotting the applicable points on logarithmic paper. Examples of
this, using the 6.8v and 200v zeners, are shown in Fig 6. Mounting contact located as specified in NOTE 3.

4 VOLTAGE REGULATION (Vz) - Test conditions for voltage regulation are as follows: Vz measurements are the made at
10% and then at 50% of the Iz max value listed in the electrical characteristics table. The test currents are the
same for the 5% and 10% tolerance devices. The test current time druation for each Vz measurement is 40±10ms.
Mounting contact located as specified in NOTE 2.

5 MAXIMUM REGULATOR CURRENT (IZM) - The maximum current shown is based on the maximum voltage of a 5% type unit.
Therefore, it applies only to the B-suffix device. The actual IZM for any device may not exceed the value of 5
watts divided by the actual Vzof the device. TL=75℃ at 3/8" maximum from the device body.
1N5333----1N5388
ZENER DIODES

RATINGS AND CHARACTERISTIC CURVES

1N5333----1N5388
ZENER DIODES

RATINGS AND CHARACTERISTIC CURVES