Exp 6

ITM UNIVERSE, VADODARA
ELECTRICAL ENGINEERING DEPARTMENT

ELECTRICAL POWER GENERATION (2140908)
Experiment no: 06
Date of Performance: _________
Date of Submission: __________
Aim: Measurements of the voltage and current of the solar cells in series and
parallel combinations.
Apparatus:
1. Solar Energy Trainer NV6005

2. Voltmeter
3. Ammeter
4. Connecting wires
Theory:
A. Introduction.
We have seen previously seen the behavior and design of solar cells in isolation. In
practice they are connected together and packaged as a module to provide specific
power output and to protect the solar cells from the elements. We need to
understand how the different connections between solar cells affect performance
– Series: give greater voltage
– Parallel: gives greater current
B. Series connection of Solar cells.
Series resistance in PV devices includes the resistance of a cell, its electrical

contacts, module interconnections, and system wiring. These resistances are in
addition to the resistance of the electrical load. Some amount of series resistance in
a PV system is unavoidable because all conductors and connectors have some
resistance. However, increasing series resistance over time can indicate problems
with electrical connections or cell degradation. Series resistance reduces the voltage
over the entire I-V curve. See Figure A.
Increasing series resistance also decreases maximum power, fill factor, and
efficiency. If a PV device is operated at constant voltage (such as for battery
charging), increasing series resistance results in decreasing operating current.
Individual cells are connected in series by soldering thin metal strips from the top
surface (negative terminal) of one cell to the back surface (positive terminal) of the
next. Modules are connected in series with other modules by connecting conductors
between the negative terminals of one module to the positive terminal of another
module. When individual devices are electrically connected in series, the positive
connection of the whole circuit is made at the device on one end of the string and the
negative connection is made at the device on the opposite end. See Figure B.
Figure A
Figure B
Only PV devices having the same current output should be connected in series.
When similar devices are connected in series, the voltage output of the entire string
is the sum of the voltages of the individual devices, while the current output for the
entire string remains the same as for a single device. Correspondingly, the I-V curve
for a string of similar PV devices is the sum of the I-V curves of the individual
devices. See Figure C.
Figure C
C. Shunt (Parallel) connection of Solar cells.
Shunt (parallel) resistance accounts for leakage currents within a cell, module, or
array. Shunt resistance has an effect on an I-V curve opposite to the effect of series
resistance. Decreasing shunt resistance reduces fill factor and efficiency, and lowers
maximum voltage, current, and power, but does not affect short-circuit current. See
Figure D. Decreasing shunt resistance over time can indicate short-circuits between
cell circuits and module frames, or ground faults within an array.
Figure D
Parallel connections are not generally used for individual PV devices, especially
cells, but for series strings of cells and modules. Parallel connections involve
connecting the positive terminals of each string together and all the negative
terminals together at common terminals or bus bars. See Figure E.
Figure E
Procedure:
A. Series combination of cells.
1. Take the Solar Energy Trainer NV6005 along with Solar Panel.
2. Place the Solar Panel in the stand and adjust the panel at an angle of about 45º
with the ground. Direct the sunlight straight at the solar panel (angle of 90º).Note:
If sunlight is not properly available then any source of light like lamp can be used.
3. With the DB15 connector connect the Solar Energy Trainer NV6005 with the Solar
Panel. Then wait for 1 minute to avoid errors due to temperature Fluctuations.
4. With the patch cords, connect outputs of all cells one by one in series such that
the positive terminal of one connected to the negative terminal of the other as.
5. Connect the positive and negative terminal of the series combination across the
voltmeter. Record the total voltage of the series combination.
6. Now connect the positive and negative terminal of the series combination across
the ammeter. Record the current of the series combination in the Observation
Table given below.
Circuit Diagram:
Observation table:
Voltage of Current of series

Sr. Solar Current
Voltage(V) series combination
No. cell (mA)
combination(V) (mA)
1 S1+S2
2 S1+S2+S3
S1+S2+S3
3
+S4
S1+S2+S3
4
+S4+S5
S1+S2+S3
5 +S4+S5+
S6
Calculations:
Sum of the voltages of all solar cells V Total = V1+ V2 +V3 + V4 + V5+V6 =
……………V
Total voltage of series combination =……….V. Hence it is clear that the total voltage
of the series combination is equal to the sum of the voltage of all solar cells.
Total current in series combination =…………….mA

Hence it is clear that the total current of the series combination is equal to the
individual current of each solar cell.
B. Parallel combination of cells.
7. Take out all the cords from the trainer.

8. With the patch cords, connect all cells one by one in parallel such that the
positive terminal of one connected to the positive terminal of the other, and also
the negative terminal of one connected to the negative terminal.
9. Connect the positive and negative terminal of the parallel combination across the
voltmeter as shown in circuit diagram. Record the voltage of the parallel
combination in the Observation Table given below.
10. Now, connect the positive and negative terminal of the parallel combination
across the ammeter as shown in figure6. Record the total current of the parallel
combination in the Observation Table given below.
Note: To measure current by on board ammeter, do not connect more than 3 solar
cells in parallel. For measuring total current of parallel combination of more than 3
solar cells, arrange a digital multimeter or analog ammeter of 1 Ampere rating in the
laboratory.
Circuit Diagram:
Observation table:
Voltage of Current of
Sr. Solar
Voltage(V) Current(mA) Parallel Parallel
No. cell
combination(V) combination(mA)
1 S1 || S2
S1 || S2 ||
2
S3
S1 || S2 ||
3
S3 || S4
S1 || S2 ||
4 S3 || S4 ||
S5
S1 || S2 ||
5 S3 || S4 ||
S5 || S6
Calculations:
Total voltage of parallel combination =………..V

Hence it is clear that the total voltage of the parallel combination is equal to the
individual voltage of each solar cell.
Sum of the current of all solar cells = I Total = I1 + I2 + I3+I4+I5+I6 = ……………mA
Total current of parallel combination =……….mA
Hence it is clear that the total current of the parallel combination is equal to the sum
of the current of all solar cells.
Conclusion:
QUESTIONS TO BE ANSWERED
1. Explain the difference between Solar Cell, Solar Module and Solar Array.
2. Why the Solar panel is kept south facing in India?
3. What are the natural factors which affect the performance of Solar Panels?
4. What are the different types of solar cell?

Exp 6

Uploaded by

Copyright:

Available Formats

Exp 6

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Exp 6

Uploaded by

Copyright:

Available Formats

ITM UNIVERSE, VADODARA

ELECTRICAL ENGINEERING DEPARTMENT

Date of Submission: __________

1. Solar Energy Trainer NV6005

B. Series connection of Solar cells.

Series resistance in PV devices includes the resistance of a cell, its electrical

C. Shunt (Parallel) connection of Solar cells.

A. Series combination of cells.

Voltage of Current of series

Total current in series combination =…………….mA

B. Parallel combination of cells.

7. Take out all the cords from the trainer.

Total voltage of parallel combination =………..V

You might also like