Universal isolated transmitter

configurable by Dip-Switch or PC

Via monte Nero, 40/B – 21049 TRADATE (VA) ITALY DAT4535

Phone: +39 (0)331841070 Fax:+39 (0)331841950 - e-mail:datexel@datexel.it - www.datexel.it
mV Tc
FEATURES
- Universal configurable input for:
mV, Tc, RTD, Res, Potentiometer, V and mA
RTD/RES
- Configurable current output from 4 to 20 mA
- Configurable by Dip-switches or by Personal \
Computer by cable CVPROG +
- High accuracy Pot
-
- On-field reconfigurable
Load
- Galvanic isolation at 1500 Vac mA
- EMC compliant – CE mark V mA
- Suitable for DIN rail mounting in compliance
with EN-50022 and EN-50035

GENERAL DESCRIPTION
The universal isolated transmitter DAT4535 is able to measure and linearise voltage, current and resistance signals, potentiometers and the standard
thermocouples and RTDs with, if required, the cold junction compensation and the wires compensation.
In function of programming, the measured values are converted and transmitted on the 4÷20 mA current loop.
The device guarantees high accuracy and performances stability both versus time and temperature.
The programming is made by the dip-switch located in the window on the side of the enclosure. By means of dip-switches it is possible to select the input
type and range without recalibrate the device.
Moreover, by Personal Computer and the cable CVPROG the user can program all of the device's parameters for his own necessity.
The terminals of the current signal on input side must be only connected to active current loop.
The 1500 Vac galvanic isolation eliminates the effects of all ground loops eventually existing and allows the use of the transmitter in heavy environmental
conditions found in industrial applications.
It is housed in a plastic enclosure of 12.5 mm thickness suitable for DIN rail mounting in compliance with EN-50022 and EN-50035 standards.
USER INSTRUCTIONS
The transmitter DAT 4535 must be powered by a direct voltage between 7 to 32 V and applied to the terminals P(+V) and O (-V) or to the terminals N(+V)
and M (-V).
The 4÷20 mA output signal is measurable in the power loop as shown in the section “Output/Power supply connections”; Rload is the input impedance of
instruments on the current loop; to obtain a correct measure, the value of Rload will be calculated as function of the power supply value ( see section
“Technical specification – Load characteristic”).
The input connections must be made as shown in the section "Input connections".
To configure and install the transmitter refer to sections "Programming”, “Configuration by dip-switches”, “Dip-switches configuration tables” and
“Installation Instructions”.
TECHNICAL SPECIFICATIONS (Typical @ 25 °C and in nominal conditions)
INPUT Linearity (1) POWER SUPPLY
Input type Min Max Min. Span Tc, RTD, Pot ± 0.1 % f.s.
mV, V, mA ± 0.05 % f.s. Supply voltage 7 .. 32 Vdc
TC (CJC int./ext.) Reverse polarity protection 60 Vdc max
J -200°C 1200°C 100°C Input impedance
K -200°C 1300°C 100°C TC, mV >= 10 MW Load characteristic - Rload (maximum load
S 0°C 1750°C 400°C Volt >= 1 MW value on current loop per power supply value)
R 0°C 1750°C 400°C mA ~22 W Ohm
B 0°C 1820°C 400°C 1K
E -200°C 1000°C 100°C RTD excitation current
T -200°C 400°C 100°C RTD,Res 400 uA 750
N -200°C 1300°C 100°C Line resistance influence (1)
Voltage TC, mV <=0.8 uV/Ohm 500

mV -100 mV +90 mV 5 mV RTD 3 wires 0.05%/W (50W max balanced) Work

mV -100 mV +200 mV 10 mV RTD 4 wires 0.005%/W (100W max balanced) area
mV -100 mV +800 mV 20 mV Thermal drift (1) 0
Volt -10 V 10 V 1V Full Scale ± 0.01% / °C 7 18 24 32 V
RTD (2, 3, 4 wires) CJC ± 0.01% / °C
Pt100 -200°C 850°C 50°C ISOLATION
CJC Comp. ± 0.5°C
Pt1000 -85°C 185°C 30°C Input – Power supply/Out 1500 Vac, 50 Hz,1 min.
Ni100 -60°C 180°C 50°C OUTPUT ENVIRONMENTAL CONDITIONS
Ni1000 -60°C 150°C 30°C
Operative Temperature -40°C ..+85°C
RES. (2, 3, 4 wires) 0W 500 W 50 W Output type Min Max Min. span Storage Temperature -40°C.. +85°C
0W 2000 W 50 W Humidity (not condensed) 0 .. 90 %
Current 4 mA 20 mA 4 mA
Maximum Altitude 2000 m
Pot. (Rnom.< 50KW) 0% 100 % 10 % Installation Indoor
Output calibration
Current 0 mA 20 mA 1 mA Category of installation II
Current ± 7 uA Pollution Degree 2
Input calibration (1) Burn-out values MECHANICAL SPECIFICATIONS
mV, TC > of ±0.1% f.s. or ±12 uV Max. output value 21.8 mA Material Self-extinguish plastic
RTD > of ±0.1% f.s. or ±0.2°C Min. output value 2.4 mA IP Code IP20
Res. > of ±0.1% f.s. or ±0.15 W Wiring wires with diameter
Response time (10÷ 90%) about 400 ms 0.8÷2.1 mm2 /AWG 14-18
Potentiometer ± 0.05 % f.s.
Volt > of ±0.1% f.s. or ± 2 mV Tightening Torque 0.8 N m
Delay on output Programmable from 0 to 30 sec.
mA > of ±0.1% f.s. or ± 6 uA Mounting in compliance with DIN
rail standard EN-50022
and EN-50035
Weight about 90 g.
EMC ( for industrial environments )
Immunity EN 61000-6-2
(1) referred to input Span (difference between max. and min. values)
Emission EN 61000-6-4
 PROGRAMMING
CONFIGURATION BY PC
Notice: before to execute the next operations, check that the
drivers of the cable CVPROG in use have been previously
installed in the Personal Computer.
By software DATAPRO it is possible to:
- set the default programming of the device;
- program the options not available with the dip-switch;
(burn-out level, CJC offset, trip alarm settings, delay on output, etc...);
- read, in real time, the input and output measures;
- follow the dip-switches configuration wizard.
DAT micro USB USB
P.C.

To configure the device follow the next steps:

1) Open the protection plastic label on the front of the device.
2) Connect the two plugs of cable CVPROG to the Personal Computer
(USB plug) and to the device (uUSB plug) . CVPROG cable
3) Run the software
4) Select the COM port in use and click on “Open COM”.
5) Select the device and connect to it.
6) Set the programming data.
7) Click “Write” to send the programming data to the device.
For information about the software refer to the its user guide.

CONFIGURATION BY DIP-SWITCHES

Input Tab. sel Opt Full Scale 1) Open the suitable door on the side of the device.

2) Set the input table selector by the dip-switch SW2 [1] (see TAB.1)

3) Set the input type by the dip-switches SW1 [1..4] (see TAB.2A and TAB.2B)

4) Set, if foreseen, the option by dip-switch SW2 [2] (see TAB.3)

5) Set the minimum value of the input scale (Zero) by dip-switches SW1 [5..8] (see TAB.4)*
SW2
6) Set the full scale value by dip-switches SW2 [3..8] (see TAB.4)*
1
Ex of configuration Pt100 3 wires -50 ÷ 200 °C:
SW1
1
SW2 =

- Input table selector (Pt100 in TAB. 2B)

- Option 3 wires
- Full scale 200 °C
SW1 =
OFF
Input type Zero - Input type Pt100
ON - Zero -50 °C

NOTE:
- It is also possible to set the dip-switches using the wizard of the configuration software following the procedure described in the section ”Configuration by
PC” until the step 6 and clicking on icon “Switch”.

DIP-SWITCH CONFIGURATION TABLES

TAB.1 – Input table selection TAB.2A – Input type selection TAB.2B – Input type selection TAB.3 - Option
SW2 TABLE SW1 SW1 SW1 SW1 SW2 CJC RTD/RES
1 123 4 12 34 1234 1234 2
TAB. 2A (mV, Volt, mA, TC) EPROM * Tc J Res. 2KW ------ External 3 wires
TAB. 2B (Res, RTD, Pot.) 90 mV Tc K Res. 500W ------ Internal 2/4 wires
200 mV Tc R Pt100 ------
800 mV Tc S Ni100 ------
10 V Tc T Pt 1K ------
20 mA Tc B Ni 1K ------
------- Tc E Pot. <500W ------
------- Tc N Pot. <50KW ------

NOTES:

* To set the input range refer to the TAB.4 (next pages) referred to the input type selected by TAB.1, TAB.2A and TAB 2B.

* If the dip-switches SW1 [1..4] and SW2 [1] are all set in the position 0 (“EPROM”), the device will follow the configuration programmed by PC ( input
type and range, output range and options).

* If the dip-switches SW1 [5..8] and SW2 [3..8] are all set in the position 0 (“Default”), the device will follow the input scale programmed by PC for the
input type selected by the dip-switches SW1[1..4] and SW2[1] .

* If the dip-switch SW2 [2] is set in the ON position and is in progress a measure by Resistance or RTD 2 wires sensor, it is necessary to
connect the terminal I to the terminal L and the terminal G to to the terminal H.
TAB.4a – mV, Tc Input scale settings
Zero Full Scale
SW1 SW2 SW2 SW2 SW2
5678 °C 345678 °C 345678 °C 345678 °C 345678 °C
Default Default 75 225 700
-200 0 80 250 750
-100 5 85 255 800
-80 10 90 275 850
-60 15 95 300 900
-50 20 100 325 950
-40 25 110 350 1000
-30 30 120 375 1100
-20 35 130 400 1200
-10 40 140 425 1300
0 45 150 450 1400
10 50 160 475 1500
20 55 170 500 1600
50 60 180 550 1750
100 65 190 600 1800
150 70 200 650 1850

TAB.4b – Pt100, Pt1K, Ni100, Ni1K Input scale settings

Zero Full Scale
SW1 SW2 SW2 SW2 SW2
5678 °C 345678 °C 345678 °C 345678 °C 345678 °C
Default Default 75 210 370
-200 0 80 220 380
-150 5 85 230 390
-100 10 90 240 400
-50 15 95 250 425
-40 20 100 260 450
-30 25 110 270 475
-20 30 120 280 500
-10 35 130 290 525
0 40 140 300 550
5 45 150 310 600
10 50 160 320 650
20 55 170 330 700
30 60 180 340 750
50 65 190 350 800
100 70 200 360 850

TAB.4c – Resistance < 2KOhm Input scale settings

Zero Full Scale
SW1 SW2 SW2 SW2 SW2
5678 W 345678 W 345678 W 345678 W 345678 W
Default Default 800 1150 1600
0 500 820 1175 1650
150 520 840 1200 1700
200 540 860 1225 1750
250 560 880 1250 1800
300 580 900 1275 1850
350 600 920 1300 1900
400 620 940 1325 1950
450 640 960 1350 2000
500 660 980 1375 2000
550 680 1000 1400 2000
600 700 1025 1425 2000
650 720 1050 1450 2000
700 740 1075 1475 2000
750 760 1100 1500 2000
800 780 1125 1550 2000
TAB.4d – Resistance < 500 ohm Input scale settings
Zero Full Scale
SW1 SW2 SW2 SW2 SW2
5678 W 345678 W 345678 W 345678 W 345678 W
Default Default 125 210 370
0 50 130 220 380
10 55 135 230 390
20 60 140 240 400
30 65 145 250 410
40 70 150 260 420
50 75 155 270 430
75 80 160 280 440
100 85 165 290 450
125 90 170 300 460
150 95 175 310 470
175 100 180 320 480
200 105 185 330 490
225 110 190 340 500
250 115 195 350 500
300 120 200 360 500

TAB.4e – Potentiometer Input scale settings

Zero Full Scale
SW1 SW2 SW2 SW2 SW2
5678 % 345678 % 345678 % 345678 % 345678 %
Default Default 34 66 98
0 5 36 68 100
15 6 38 70 100
20 8 40 72 100
25 10 42 74 100
30 12 44 76 100
35 14 46 78 100
40 16 48 80 100
45 18 50 82 100
50 20 52 84 100
55 22 54 86 100
60 24 56 88 100
65 26 58 90 100
70 28 60 92 100
75 30 62 94 100
80 32 64 96 100

TAB.4f – mA Input scale settings

Zero Full Scale
SW1 SW2 SW2 SW2 SW2
5678 mA 345678 mA 345678 mA 345678 mA 345678 mA
Default Default 8 11.5 16
0 5 8.2 11.75 16.5
1.5 5.2 8.4 12 17
2 5.4 8.6 12.25 17.5
2.5 5.6 8.8 12.5 18
3 5.8 9 12.75 18.5
3.5 6 9.2 13 19
4 6.2 9.4 13.25 19.5
4.5 6.4 9.6 13.5 20
5 6.6 9.8 13.75 20
5.5 6.8 10 14 20
6 7 10.25 14.25 20
6.5 7.2 10.5 14.5 20
7 7.4 10.75 14.75 20
7.5 7.6 11 15 20
8 7.8 11.25 15.5 20
 TAB.4g – Volt Input scale settings
Zero Full Scale
SW1 SW2 SW2 SW2 SW2
5678 Volt 345678 Volt 345678 Volt 345678 Volt 345678 Volt
Default Default 3.4 6.6 9.8
0 0.5 3.6 6.8 10
1.5 0.6 3.8 7 10
2 0.8 4 7.2 10
2.5 1 4.2 7.4 10
3 1.2 4.4 7.6 10
3.5 1.4 4.6 7.8 10
4 1.6 4.8 8 10
4.5 1.8 5 8.2 10
5 2 5.2 8.4 10
5.5 2.2 5.4 8.6 10
6 2.4 5.6 8.8 10
6.5 2.6 5.8 9 10
7 2.8 6 9.2 10
7.5 3 6.2 9.4 10
8 3.2 6.4 9.6 10

CONNECTIONS
INPUT CONNECTION POWER SUPPLY / OUTPUT CONNECTION
mV TC RTD/RES 2W (*) RTD/RES 3W
P
L L G G +
+ +
7÷32 Vdc
H Iout
I I I O Rload
+

I
Terminal P = N; Terminal O = M

RTD/RES 4W Note: Terminal R = Q = Not connected (NC)

Pot V Passive mA input
Connected to active
G G + E current loop

H + F ISOLATION STRUCTURE
H - I

L I Input side, Power supply / output

I
- prog. side
I

Terminal I = GND INPUT

Note: if the device is programmed by dip switches for RTD / RES with 2 wires
connection make a short circuit between the terminals I and L and the terminals
G and H.

DIMENSIONS (mm) INSTALLATION INSTRUCTIONS

The device DAT 4535 is suitable for DIN rail mounting.

It is necessary to install the device in a place without vibrations; avoid to
routing conductors near power signal cables .
90

HOW TO ORDER
The device is provided as requested on the Customer's order.
Refer to the section “Programming” to determine the input ranges.
In case of the configuration is not specified, the parameters must be set by the user.

ORDER CODE EXAMPLE

DAT4535 / Pt100 / 0 ÷ 200 °C / 3 wires / 4 ÷ 20 mA
12.5 112
Input type
The symbol reported on the product indicates that the product itself must not be
Input range
considered as a domestic waste.
It must be brought to the authorized recycle plant for the recycling of electrical and
Options
electronic waste.
For more information contact the proper office in the user's city , the service for the waste
Output range
treatment or the supplier from which the product has been purchased.

Datexel reserves its rights to modify totally or in part the characteristics of its products without notice at any time . ED.04.13-R.06