MG5728

Operating Manual
az
Deutz TCD L6
Euro 4 Emission Standard
Please read this operating

MG5728
manual before commissioning.
BAG0174.1 01.18
Printed in Germany Keep it in a safe place
for future use!
en
7&'/
7&'77&'/
2SHUDWLQJPDQXDO
(86WDJH,986(3$7LHU
Notes
Notes ● Do not change the cooling air feed area to the Danger due to high pressure of leaks — Danger to
blower or fan. An unobstructed cooling air supply life!
● This engine is defined exclusively for purpose must be guaranteed.
according to the scope of delivery and built by the – In case of leaks contact the workshop
equipment manufacturer (use for the intended The manufacturer willl accept no liability for immediately.
purpose). Any other use above and beyond this frfom this.
damages resulting from
– In the case of works on the fuel system ensure
will be considered as misuse. The manufacturer ● As a general rule, e, only DEUTZ original
orig parts may that the engine is not started unintentionally
will not accept any liability for damages resulting be used when carrying out mainte t na
maintenance/repair during the repair works — Danger to life!
from this. The user bears the sole risk. work on the engine. TheThesee have been designed
● Use for the intended purpose also includes especiallyy for
f r yo
fo yyour
ur eng nd ensure fa
engine and ffault-free
observance of the operating, maintenance and n.
operation.
repair instructions specified by the manufacturer. The guarantee
uarante
t e wi
will be void in thee event of non-
no
The engine may only be used, maintained and pliance!
compliance!
serviced by persons who are familiar with it and are
aware of the hazards. Mainte
Main ten
t nance
ance/cleaning
ing work on
o the engine
ngine may
The relevant rules for the prevention of accidents oonly
nly be carried
ca out when the engine is not running
and other generally recognised safety and aand
nd has cooled down.wn. When performing such
occupational medicine rules must be observed. w orks
k make sure that
works, at the electrical
ele system is
sswitched
witc
t h off (removee ig gnition key).
ignition
● When the engine is running there is a danger of
injury caused by: The
Th rules for the prevention
vention of accidents on
g. -VDE-
electrical systems (e.g. -VDE
– rotating and hot components 0100/-0101/-0104/-0105 105 E
Electrical Protection
– in the case of engines with external ignition ngero Live Voltages) must
Measures against Dangerous
(high electrical voltage), contact must be be observed.
avoided!
Cover all electrical components
c mpone tightly when
co
● Unauthorised modifications to the enginee will ds.
cleaning with liquids.
lity
t for
exclude the manufacturer from all liability f r
fo
resulting damage. ● Do not work on the fuel
uel system
sys
y te
t while the engine is
● Equally, manipulations to the injection
c ion and control
ct c
co running — Danger to life!
erfo
f rmance and
system can affect the engine's performance Wait
W ait for
f r the pressure to
fo t be relieved once the
his case, compliance
the exhaust characteristics. In this c mpliance
co eengine
ngine has shut down (for (fo
f r engines with common
c mmon
co
with environmental regulations will no longer be rail, approx. 5 minutet s, otherwise
minutes, otherw
r ise 1 minute)
minute
t ) as the
guaranteed. system is under high pressure — Danger to life!
During the first trial run do not stand in the engine
hazard zone.
2 © 08/2017
Foreword
Dear customer, DEUTZ engine registration
Congratulations on the purchase of your DEUTZ
engine.
Components of the exhaust aftertreatment system
The liquid-cooled engines made by DEUTZ are
developed for a wide variety of applications. A Please enter the serial numbers of the exhaust
comprehensive range of variants ensures that the aftertreatment components.
respective special requirements are fulfilled. Diesel oxidation catalytic converter
The engine is equipped accordingly for the particular
installation situation, i.e. not all the components
described in the operating manual are installed in
your engine.
Diesel particle filter
We have endeavoured to highlight any differences so
that you will be able to locate the operating and
maintenance instructions applicable to your engine
quickly and easily. DEUTZ AG aims to provide an excellent service
worldwide. In order to ensure this, information about
SCR catalytic converter
Please make sure that this operating manual is the locations of devices with DEUTZ engines is very
available to everyone involved in the operation, helpful.
maintenance and repair of the engine and that they
have understood the contents. DUETZ engine registration is available for you at
www.deutz.com or using the code. You can enter your
If you have any queries, please contact us, we'll be Notes DEUTZ engine data there directly so that your engine
happy to advise you. can receive the best possible maintenance from the
Illustrations and data in this instruction manual are
global DEUTZ Service Network.
Sincerely, subject to technical changes in the course of further
development of the engine.
DEUTZ AG
No parts of this document may be reproduced in any
Engine number form or by any means without our express approval.
Please enter the engine serial number here. This will
simplify the handling of customer service, repair and
spare parts queries.
© 08/2017 3
Table of contents
1RWHV /XEULFDWLQJRLOV\VWHP
)RUHZRUG )XHOV\VWHP
*HQHUDO 6&56HOHFWLYH&DWDO\WLF5HGXFWLRQ
(QJLQHGHVFULSWLRQ &RROLQJV\VWHP
0RGHO 6XFWLRQV\VWHP
(QJLQHLOOXVWUDWLRQ %HOWGULYHV
/XEULFDWLQJRLOSODQ $GMXVWPHQWZRUN
)XHOV\VWHPSODQ (QJLQHFOHDQLQJ
&RRODQWSODQ (OHFWULFDOV\VWHP
([KDXVWJDVUHFLUFXODWLRQ )DXOWV
([KDXVWJDVDIWHUWUHDWPHQW )DXOWWDEOH
(OHFWULFV(OHFWURQLFV (QJLQHPDQDJHPHQW
2SHUDWLRQ 7UDQVSRUWDQGVWRUDJH
$PELHQWFRQGLWLRQV 7UDQVSRUW
,QLWLDOFRPPLVVLRQLQJ (QJLQHFRUURVLRQSURWHFWLRQ
6WDUWSURFHVV 7HFKQLFDOGDWD
2SHUDWLRQPRQLWRULQJ (QJLQHDQGVHWWLQJGDWD
([KDXVWJDVDIWHUWUHDWPHQWV\VWHP 7RROV
3DVVLYHUHJHQHUDWLRQ
6WRSSLQJSURFHVV
2SHUDWLQJPHGLD
/XEULFDWLQJRLO
)XHO
&RRODQW
6&5UHGXFWLRQDJHQW
0DLQWHQDQFH
0DLQWHQDQFHVFKHGXOH
6HUYLFHDQGPDLQWHQDQFHZRUN
4 © 08/2017
General
DEUTZ diesel engines Original DEUTZ parts Please contact your service partner in case of
malfunctions and spare parts inquiries. Our specially
DEUTZ diesel engines and the appropriate exhaust Original DEUTZ parts are subject to the same strict trained personnel will ensure fast, professional repairs
aftertreatment components are the result of years of quality demands as the DEUTZ engines. Of course, using original DEUTZ spare parts in case of damage.
research and development. The detailed know-how further developments for the improvement of the
gained by this in connection with the high quality engines are also introduced in the original DEUTZ The DEUTZ homepage provides a continuously
demands are the guarantee for production of engines parts. Only the use of original DEUTZ parts updated overview of the service partners near you,
with a long life, high reliability and low fuel manufactured according to the state-of-the-art can and information on product areas and services.
consumption. Naturally the high demands for guarantee perfect functioning and high reliability.
protection of the environment are also met. Imprint
DEUTZ Xchange components
Safety precautions when the engine is running DEUTZ AG
DEUTZ replacement parts are a low-cost alternative. Ottostraße 1
Maintenance work or repairs may only be performed Of course, the quality standards here are just as high 51149 Cologne
on the shut-down engine. Make sure that the engine as for new parts. DEUTZ replacement parts are equal Germany
cannot be started inadvertently - Danger of accident! to the original DEUTZ parts in function and reliability. Telephone:+49 (0) 221-822-0
Fax:+49 (0) 221-822-3525
After repairs: Check that all protective equipment is Asbestos Email:info@deutz.com
mounted and all tools have been removed from the www.deutz.com
engine. The gaskets used in this engine contain no asbestos.
Please use the appropriate original DEUTZ parts for Danger
Observe industrial safety regulations when running maintenance and repair work.
the engine in an enclosed space or underground. This symbol is used in all safety instructions
Service
When working on the running engine, work clothing which, if not observed, present a direct
must be close fitting. We want to preserve the high performance of our danger to life and limb for the person
engines and with it the confidence and satisfaction of involved. Pay attention to it carefully. Forward
Never fill the fuel tank while the engine is running. our customers. Which is why we have a global network safety instructions to your operating
of service branches. personnel as well. Furthermore, the
Service and maintenance legislation for "general regulations for safety
The name DEUTZ means more than just engines and the prevention of accidents" must be
Service and maintenance are the prerequisite for the created as a result of sophisticated development work, observed.
engine satisfying the demands placed on it. it also stands for a complete service package that
Compliance with the specified maintenance intervals guarantees the optimum operation of our engines as Caution
and careful execution of service and maintenance well as customer service that you can count on.
work are therefore absolutely necessary. This symbol indicates a danger to the part
Special care should be taken under abnormally and engine. The relevant instructions must be
demanding operating conditions. observed, failure to do so can lead to
destruction of the part and the engine.
© 08/2017 5
General
Notes
You will find this symbol in all instructions of

the general type.
CALIFORNIA PROPOSITION 65 WARNING
Engine exhaust, some of its constituents, and

a broad range of engine parts are known to
the State of California to cause cancer, birth
defects and other reproductive harm.
Additionally, lubricants, fuels and other fluids
used in engines including any waste created
through the wearing of engine parts contain
or produce chemicals known to the State of
California to cause cancer and birth defects
or other reproductive harm.
6 © 08/2017
Model Engine description
Engine type designation They are only certified by the responsible
authorities and comply with the permissible
This manual covers the following engine types
exhaust limits in this combination. Operation
TCD 4.1 L4 of the engine with other EAT systems is not
allowed.
TCD 6.1 L6
The engines of these operating instructions fulfill the
TTCD 6.1 L6
following exhaust emissions regulations
TCD With exhaust aftertreatment system
T Turbocharger USA EPA Tier 4 final
TT Two-level exhaust turbocharging EU Stage IV
C Charge air cooler
The exact certification is printed on the engine rating
D Diesel plate.
4.1 / 6.1 The engines of this operating manual may Rating plate
4.1 Displacement in litres only be used with a functioning exhaust The type (A), engine number (B) and performance
6.1 Displacement in litres aftertreatment system (provided this is data are stamped on the rating plate.
included in the DEUTZ scope of deliver).
L4 / 6 The engine type and number must be stated when
purchasing spare parts.
L in a row
4 Number of cylinders
6 Number of cylinders
Emissions legislation
The engine and the corresponding EAT

system (Exhaust After Treatment) are
adapted to each other and linked by an
appropriate electronic controller.
© 08/2017 7
Engine description Model
Position of the rating plate Engine number Serial numbers of the exhaust aftertreatment
components
The rating plate (C) is fixed to the cylinder head cover The engine number (D) is stamped onto the crankcase
or the crankcase. (arrow) and onto the rating plate. 1 Rating plate of the diesel particle filter
2 Rating plate of the SCR catalyst
The serial numbers of the exhaust aftertreatment

components are stamped on the rating plates.
8 © 08/2017
Model Engine description
Serial numbers of the exhaust aftertreatment Cylinder numeration

components
I Left
1 Rating plate of the diesel particle filter II Right
2 Rating plate of the SCR catalyst
Cylinder arrangement
The serial numbers of the exhaust aftertreatment
components are stamped on the rating plates. The cylinders should be counted consecutively starting
from the flywheel (1).
Direction of rotation
Looking onto the flywheel.
Left-hand rotation: anti-clockwise
Engine sides
Looking onto the flywheel.
© 08/2017 9
Engine description Engine illustration

TCD 4.1 L4
Industrial engine
View from right (example)
1 Combustion air inlet
2 V-rib belts
3 Tension pulley
4 Fuel spare filter
5 Lubricating oil drain plug
6 Lube oil spare filter
7 Lubricating oil dipstick
8 Lubricating oil cooler
9 High-pressure storage vessel (rail)
10 Lube oil filling
11 Crankcase ventilation
10 © 08/2017
Engine illustration Engine description
TCD 4.1 L4
Industrial engine
View from left (example)
2 Coolant outlet
3 Coolant inlet
4 Exhaust outlet
© 08/2017 11

TCD 4.1 L4
Agricultural engineering
2 V-rib belts
3 Tension pulley
4 Coolant inlet
7 Alternator
9 Fuel spare filter
11 Lube oil filling
12 © 08/2017
TCD 4.1 L4
2 Exhaust outlet
3 Lube oil filling
© 08/2017 13

TTCD 6.1 L6
2 Alternator
3 V-rib belts
4 Coolant inlet
8 Fuel spare filter
10 Lube oil filling
14 © 08/2017
TTCD 6.1 L6
2 Coolant outlet
3 Exhaust outlet
5 Lube oil filling
© 08/2017 15
Engine description Lubricating oil plan

Lubricating oil system
(example)
1 Lubricating oil pan
2 Lubricating oil pump
3 Pressure limiting valve
5 Check valve
6 Bypass valve
7 Bypass valve
8 Pressure control valve
9 Lubricating oil filter
10 Main lube oil channel
11 Piston cooling nozzle
12 Rocker arm
13 Exhaust turbocharger
14 Compressor
Optional
16 © 08/2017
Fuel system plan Engine description
Fuel system plan
(example)
1 Fuel tank
2 Fuel pre-filter
3 Fuel supply pump
4 Fuel spare filter
5 Fuel supply line to the control block FCU (Fuel
Control Unit)
6 Control block FCU (Fuel Control Unit)
7 High-pressure pump
9 Injector
10 Fuel return to the fuel tank
11 Return line
© 08/2017 17
Engine description Coolant plan

Coolant plan
(example)
Industrial engine
1 Cooler
2 Coolant pump
4 Coolant supply for engine cooling
5 Cylinder pipe/head cooling
6 Compressor
Optional
7 Connection possibility for cab heating
8 Metering module
9 AdBlue® tank
10 Exhaust return cooler.
11 Temperature sensor
12 Thermostat
13 Compensation tank
18 © 08/2017
Coolant plan Engine description
Coolant plan
(example)
1 Cooler
TTCD 6.1 L6
2 Cooler
3 Coolant pump
4 Electronic coolant pump
TTCD 6.1 L6
6 Coolant supply for engine cooling
7 Cylinder pipe/head cooling
8 Charge air intercooler
TTCD 6.1 L6
9 Compressor
Optional
10 Connection possibility for cab heating
11 Metering module
12 AdBlue® tank
15 Thermostat
TTCD 6.1 L6
© 08/2017 19
Engine description Exhaust gas recirculation

External exhaust return
1 Exhaust partial flow
(uncooled)
2 Coolant intake
3 Actuator
(electric)
5 Flutter valve
6 Coolant return
8 Exhaust partial flow
(cooled)
20 © 08/2017
Exhaust gas aftertreatment Engine description
Exhaust gas aftertreatment system
1 SCR supply pump
2 SCR tank
3 Coolant line
for preheating the SCR tank
4 Throttle valve
5 Diesel particle filter
6 Pressure sensor
7 NOx sensor
8 Differential pressure sensor
10 NOx sensor
11 SCR catalytic converter
12 Metering unit
13 Coolant line
for cooling the metering unit
14 SCR line
© 08/2017 21
Engine description Exhaust gas aftertreatment

Exhaust gas aftertreatment system
Industrial engine
1 SCR supply pump
2 SCR tank
3 Coolant line
for preheating the SCR tank
for cooling the metering unit
4 SCR line
5 NOx sensor
6 Metering unit
7 NOx sensor
9 Pressure sensor
10 SCR catalytic converter
11 Differential pressure sensor
13 Diesel particle filter
14 Throttle valve
22 © 08/2017
Electrics/Electronics Engine description
Electronic engine control
1 Speed transmitter via camshaft
2 Control block FCU (Fuel Control Unit)
3 Central connector (for engine control unit)
4 Charge air pressure transmitter, charge air
temperature transmitter
5 Exhaust gas backpressure sensor
6 Differential pressure flow meter
7 Throttle valve
8 Heating flange
9 Rail pressure sensor
10 Speed transmitter via crankshaft
11 Lubricating oil pressure transmitter
12 Starter
13 Coolant temperature transmitter
14 Exhaust gas return actuator
© 08/2017 23
Engine description Electrics/Electronics

Information about the engine electronics Diagnostic and maintenance work may only ● Error lamp (flash code)
be carried out by authorised personnel using ● CAN bus
This engine is equipped with an electric control unit.
equipment approved by DEUTZ.
● DEUTZ electronics display
The equipping of the respective system depends on
the desired scope of function and the planned type of Installation notes ● Diagnostic socket (SERIDA)
engine application. Equipment-side wiring
The control units are calibrated to the respective
DEUTZ AG installation regulations must also be taken engine and identified by the engine number. Every
engine may only be operated with the appropriate The DEUTZ AG installation regulations must be
into account. adhered to. In particular, the plug contact must be
control unit.
Precautions crimped with the appropriate standard tools. If it is
Nominal value sensors (pedal position sensors) necessary to do so, plugged-in contacts may only be
The connections of the control units are only required for vehicle operation must be connected to removed from the plug housing with the proper tools.
dust and water proof when the mating plugs the cable harness on the vehicle side and calibrated
are plugged (protection class IP69K)! The using the DEUTZ diagnostic program SERDIA
control units must be protected against spray (SERvice DIAgnosis). Wiring and cable assignment of
water and moisture until plugging in the the vehicle side cable harness must be taken from the
mating plugs! DEUTZ connection diagram.
Reverse polarity can lead to failure of the
Supply voltage
control units.
To avoid damaging the control units, all the 12 Volt
connections on the control unit must be
disconnected before electric welding work. 24 Volt
Interventions in the electrical system contrary
to the DEUTZ regulations or by unqualified Sufficient charging of the battery must be ensured.
personnel can permamently damage the Interruption of the power supply while the engine is
engine electronics and have serious running can cause damage to the electrics/electronics.
consequences which are not covered by the If the supply voltage fails, the engine will shut down.
manufacturer's guarantee. Voltages above 32 Volt will destroy the control unit.
It is strictly prohibited:
a) to make changes or add connections to the Diagnostics
wiring of the electrical control devices and the
data transmission cable (CAN lines). DEUTZ control units are equipped with self-
b) to switch control units. diagnostics. Active and passive error entries are saved
Otherwise guarantee rights will be lost! in the error memory. Active errors are displayed on
error lamps/diagnostics lamps 77.
A diagnosis can be made with:
24 © 08/2017
Ambient conditions Operation
Use of engines in low load operation (engine does not Coolant
reach the operating temperature) over a long time
period under cold climatic conditions results in fuel ● Observe the mixing ratio of anti-freeze/cooling
waste, increased wear and potentially to engine water 47.
damage. These low temperature conditions result in The following possibilities can be considered by the
incomplete combustion and therefore to a build-up of device manufacturer or retrofitted by authorised
deposits on components within the engine. In addition, specialist personnel:
operating an engine with low exhaust temperatures
and low exhaust gas mass flow can cause premature ● Warming the cooling circuit and/or the oil circuit
faults such as engine or the exhaust aftertreatment when the engine is not running.
system failure. ● Maintaining the desired engine operation
The following measures can be taken by the temperature, particularly in low-load operation,
operator: requires:
– Superimposition of additional load through the
Lubricating oil application.
Low ambient temperature
● Select the lubricating oil viscosity according to the – Use of a device cooler hood or housing.
The operation of engines under cold or even Arctic ambient temperature. – Housing the oil pan and the underside of the
climatic conditions requires modifications to the engine ● Halve the oil change times in case of frequent cold engine in order to protect against cold air
during installation, engine operation and starts. through the engine fan.
maintenance. If these modifications are not taken into
account, this can have an impact on the engine Fuel – If possible, use of a temperature-dependent fan
starting properties, performance, reliability and the coupling.
● Use winter fuel below 0 °C 46.
operation of the corresponding exhaust aftertreatment ● Insulation of fuel lines, filters, pumps or even tanks.
system. Battery
● Warming of the intake air through intake air
● The battery must be well-charged before the preheating or diverting the warm engine
Operating an engine under cold or Arctic
engine is started 71. compartment air.
climatic conditions without suitable
modifications can affect the warranty. ● Warming the battery to about 20°C improves the ● Warming the crankcase ventilation.
engine starting behaviour. (Remove and store the If you have any additional questions, please contact
battery in a warm room). your equipment supplier or DEUTZ partner.
Cold start aid
High ambient temperature, high altitude
● The engines in these operating instructions are
equipped with glow plugs 30. These engines are equipped with an electric
control unit.
© 08/2017 25
Operation Ambient conditions

Under the operating conditions listed below,
the amount of fuel is reduced automatically,
controlled by the electronic control unit.
● Application at high altitude

● Application at high ambient temperatures
Reason: Air density decreases as altitude or ambient
temperature increase. This also reduces the quantity
of oxygen in the engine intake air resulting in a fuel/air
mixture that is too fatty without any reduction in the fuel
injection rate.
● The results would be:
– black smoke in the exhaust
– high engine temperature
– reduced engine performance
– possible impairment of the starting behaviour
If you have any additional questions, please contact
your equipment supplier or DEUTZ partner.
26 © 08/2017
Initial commissioning Operation
Preparation for initial commissioning The engines are generally supplied without
lubricating oil filling.
(maintenance schedule E 10)
Select the engine lubricating oil quality and
● Remove corrosion protection from protected viscosity before filling.
engine. DEUTZ lubricating oils can be ordered from
your DEUTZ partner.
● Remove and existing transport devices.
● Check battery and cable connections and install if ● Fill the engine with lubricating oil via the oil filler
necessary. neck.
● Check the belt tension 65. ● Observe the lubricating oil filling level 83.
● Have the engine monitor or warning system
checked by authorised personnel.
● Check engine mounting.
● Check all hose connections and clips for correct fit.
Pour in fuel
The following actions must be performed
additionally for generally overhauled engines: Never fill the fuel tank while the engine is
running.
● Check the fuel pre-filter and main filter and change
Pay attention to cleanliness. Do not spill any
if necessary.
fuel.
● Check suction intake air filter (if available, maintain Additional venting of the fuel system by a 5-
according to maintenance pointer). minute trial run on no-load or low load is
● Drain lubricating oil and condensation from the C- absolutely essential.
intercooler. Only use clean commercially available brand
diesel fuel. Observe fuel quality 46.
● Fill up with engine lubricating oil.
Use summer or winter-grade fuel depending
● Filling the coolant system 83. on the ambient temperature.
Fill up with engine lube oil. ● Fuel low-pressure system must be vented before
initial start-up after filling with the electric fuel
Lack of lube oil or overfilling lead to engine supply pump. 56.
damage.
© 08/2017 27
Operation Initial commissioning

If the filled medium (e.g. diesel) has not ● Check the coolant level and top up coolant if
reached the lines and supply pump/metering necessary.
module, emptying and thoroughly cleaning
the AdBlue® tank is sufficient. Danger of scalding from hot coolant!
Pay attention to cleanliness. Cooling system under pressure!
Only open the cap when cool! Observe safety
AdBlue® minimum refilling quantity regulations and national specifications when
handling cooling media.
When fuelling with AdBlue®, the following minimum
refilling quantities must be adhered to. Fuelling below ● If required, repeat procedure with engine start.
the prescribed minimum refill quantity is only ● Fill up coolant to the MAX mark on the
permissible if the tank does not have sufficient spare compensation tank and close the cooling system
tank volume at the time of fuelling. cap.
Tank volume Minimum refilling quantity ● Switch on any available heating and set to the
< 20 litres 5 litres or a full tank highest level so that the heating circuit is filled and
Filling with AdBlue® vented.
≥ 20 litres 10 litres or a full tank
● Observe the filling volume of the cooling system
AdBlue® is known by different names
Filling the coolant system 83.
depending on the region:
in the USA as DEF (Diesel Exhaust Fluid), in Trial run
Brazil as ARLA32. The coolant must have a prescribed
The technical designation is AUS32. concentration of cooling system corrosion
Additional venting of the fuel system by a 5-
AdBlue® is a registered trademark of the protection agent!
minute trial run on no-load or low load is
Verband der Automobilindustrie e.V (VDA - Never operate the engine without coolant, not
absolutely essential.
German Association of the Automotive even briefly!
Industry). Carry out a brief trial run up to operating temperature
Order coolant corrosion protection agent (approx. 90 °C) after preparations.
Only re-fuel when the engine is not running. from your DEUTZ partner.
Only fill with AdBlue®! Do not load the engine if possible.
Other media (e.g. diesel), even in the ● Fill cooling system via the compensation tank. ● Work with the engine not running:
smallest amounts, can cause destruction of
● Close compensation tank with valve. – Check engine for tightness.
the system.
If you have filled with e.g. diesel and this has ● Start the engine and warm up until the thermostat – Check lubricating oil level, if necessary re-fill
got into the system, the complete AdBlue® opens.
– Check the coolant level and top up coolant if
injection system must be replaced! ● Engine operation with open thermostat 2 - 3 necessary.
minutes. ● Work during the trial run:
28 © 08/2017
Initial commissioning Operation
– Check engine for tightness.
© 08/2017 29
Operation Start process

Before starting make sure that there is ● the maximum start duration is limited.
nobody in the engine/work machine hazard ● the pause between two start attempts is specified.
zone.
– the start is then continued automatically
After repairs: Check that all protective
equipment is mounted and all tools have ● starting while the engine is running is prevented.
been removed from the engine. If the touch start function is programmed, a short start
When starting with glow plugs do not use any command with the ignition key in position 2 or a start
additional starting devices (e.g. injection with button, if available, suffices.
start pilot). Danger of accident!
If the engine fails to fire and the error lamp

lights, the electronic engine control has
activated the start lock to protect the engine.
The start lock is released by switching off the
system with the ignition key for about 30
seconds. with cold starting device
Start the engine for a maximum of 20
seconds uninterrupted. If the engine does not ● Insert key.
start up, wait for one minute and then repeat – Step 0 = no operating voltage.
the starting process. ● Turn key to the right.
If the engine does not start up after two
starting processes, determine the cause as – Step 1 = operating voltage.
per fault table. 72. – Engine is ready for operation.
Do not run the engine up to high idling
● The electronic engine control activates the current
speed/full load operation straight from cold.
feed to the glow plugs when the engine coolant
temperature falls below a certain temperature.
Disconnect the engine by uncoupling devices
to be driven where possible. ● Push in the key and turn further to the right against
the spring pressure.
– Level 2 = start.
● release the key as soon as the engine starts up.
– Pilot lamps go out.
If the starter is controlled by the electronic engine
control via a relay:
30 © 08/2017
Operation monitoring Operation
Electronic engine control – Engine forced to run at low power to cool the
engine, with automatic shutdown if necessary.
The system monitors the condition of the engine and
itself. – The switch-off process has been accomplished.
– There may be a start lock after engine stop.
● Function test
– The start lock is deactivated by turning off the
– Ignition on, error lamp lights up for approx. 2 system with the ignition key for approx. 30
seconds and then goes out. seconds.
– Check the error lamp if there is no reaction after – Additional control lamps, e.g. for lubricating oil
switching on the ignition. pressure or lubricating oil temperature, are
● Error light does not light up. switched on if necessary.
– After the lamp test an extinguished lamp – In order to avoid critical situations the power
indicates an error-free and trouble-free reduction can be bypassed, automatic switch-off
operating state within the scope of the control delayed or a start lock bypassed using the
possibilities. optional override key on the instrument panel.
This brief deactivation of the engine protection Display instrument
● Continuous light
functions is logged in the control unit. Possible displays:
– Error in system.
The engine protection functions are released in co-
– Operation continued with restrictions. operation with the equipment manufacturer and the ● Colour scale
– The engine must be checked by a DEUTZ DEUTZ installation consulting and may be designed – Display of operating state by coloured areas:
partner. individually. This is why the operating manual of the – green = normal operating state
– If a lamp lights steadily a monitored measuring device manufacturer must be observed.
– red = critical operatng state
variable (e.g. coolant temperature, lubricating Take suitable action.
oil pressure) has left the permissible value
range. ● Measured value scale
Depending on the fault, the engine power may be – Actual value can be seen directly. The target
reduced by the electronic engine control to protect the value must be taken from the technical data.
engine. 83.
● Flashing
– Serious error in system.
– Switch off prompt for the operator. Attention:
Failure to do so will lead to loss of guarantee!
– The engine has reached switch-off condition.
© 08/2017 31
Operation Operation monitoring

Instruments and symbols
Instruments/symbols Designation Possible displays Measure

Lube oil pressure indicator Lubricating oil pressure in the red Switch off engine
Coolant temperature Coolant temperature too high Switch off engine
Lubricating oil temperature Lubricating oil temperature too high Switch off engine
Lubricating oil pressure control Lubricating oil below minimum Switch off engine
light
Lubricating oil level Lubricating oil pressure too low Fill up lubricating oil
Coolant level Coolant level too low Shut down the engine, allow to cool and top up coolant
Operating time counter Indicates the engine operating time passed Observe the maintenance intervals
32 © 08/2017
Operation monitoring Operation
Instruments/symbols Designation Possible displays Measure
Horn With acoustic signal See fault table 72
SCR function lamp Continuous light Check AdBlue® filling level

flashes (0.5 Hz) Check SCR system
flashes (1 Hz)
flashes (2Hz)
Ash lamp Continuous light The ash lamp indicates, that loading of the diesel particle
filter with incombustible residues has reached a critical
level and must be replaced. 40
Regeneration lamp Continuous light Initiate standstill regeneration 40

flashes (0.5 Hz)
flashes (3 Hz)
Engine warning lamp Continuous light Initiate standstill regeneration in combination with the
Flashing DPF function lamp 40
© 08/2017 33
Operation Operation monitoring

● Fuel pressure
● Status of the regeneration of the diesel particle
filter
● Operation monitoring of the diesel particle filter
● Faults in the exhaust aftertreatment system
● Filling level of the SCR tank
● Battery voltage
● Position of accelerator pedal
● Fuel consumption
● Operating hours
Error messages are displayed in clear text and
acoustically; the error memory of the control unit can
DEUTZ Electronic Display be read out.
In order to show measured values and error For a detailed description, refer to the operating
messages of the EMR control unit, a CAN display is instructions enclosed with the DEUTZ Electronic
optionally available, which can be integrated into the Display.
dashboard of the driver´s position of working
machines.
The following data may be displayed if they are sent by
the control unit.
● Engine speed
● Engine torque (current)
● Coolant temperature
● Intake air temperature
● Exhaust gas temperature
● Lubricating oil pressure
● Coolant pressure
● Charge air pressure
34 © 08/2017
Exhaust gas aftertreatment system Operation
Selective Catalytic Reduction (SCR) Emission-relevant faults are: This function is available for engines with power
reduction levels 1 and 2, in accordance with EU
AdBlue® is known by different names ● SCR fill level legislation, and with power reduction level 1, in
depending on the region: ● Catalytic converter efficiency/Adblue® quality accordance with EPA legislation.
in the USA as DEF (Diesel Exhaust Fluid), in
Brazil as ARLA32. ● Manipulation Standstill regeneration
The technical designation is AUS32.
AdBlue® is a registered trademark of the ● System fault Temperatures of approx. 600 °C occur on the
Verband der Automobilindustrie e.V (VDA - exhaust pipe during regeneration.
German Association of the Automotive An acoustic signal must sound in case of a A special engine operating state becomes
Industry). fault. If a DEUTZ display is used, this has an active during standstill regeneration and the
appropriate signal. machine is not allowed to be used during the
The DEUTZ SCR system reduces the NOx emissions An acoustic signal transmitter must be active standstill regeneration.
from the engine (NOx=nitric oxides). installed additionally if an SCR function lamp Danger of burns!
or customer display is used.
A reduction agent, AdBlue®, injected into the exhaust The SCR system is monitored for possible formation
system reacts in the SCR catalytic converter with the Power reduction and build-up of crystals (crystallisation)
NOx emissions in the exhaust gas and reduces these
to nitrogen (N2) and water (H2O). If a serious fault occurs or a fault is not remedied, the As soon as crystalisation is detected, a standstill
system reacts by reducing the engine performance. regeneration request is issed.
The injected volume of SCR is controlled by the
engine electronics. There is a one or two-stage performance reduction This is displayed by a flashing regeneration lamp.
depending on the type of fault.
Warning strategy SCR system The standstill regeneration must be initiated by the
Power reduction operator.
The display and monitoring of the exhaust Stage 1 Torque reduction It is recommended that standstill regeneration be
aftertreatment system can be executed either undertaken as soon as possible.
Stage 2 Torque reduction
with pilot lights or with a CAN interface and a
+ Engine speed limitation
corresponding display, depending on the If standstill regeneration is not undertaken, the engine
engine version. Bridging of the power reduction control unit will activate the specified engine protection
Please see the device manufacturer's functions.
operating manual. A separate emergency switch has been provided, in
order to temporarily disable power reductions caused Every standstill regeneration slightly dilutes the engine
In order to comply with the regulations of the by the EAT system. oil with fuel. The number of standstill regenerations is
European Union (EU) and the Environmental therefore monitored.
Protection Agency (EPA), the DEUTZ SCR system This function is available for a limited period and is
reacts with a warning strategy to faulty operation of the expected to enable the user to move the machine to a
exhaust gas aftertreatment system. safe location.
© 08/2017 35
Operation Exhaust gas aftertreatment system

SCR filling level
Warnings begin from an SCR filling level below 15 %.
SCR filling level SCR function lamp Engine warning lamp DEUTZ CAN display Power reduction
< Continuous light OFF SCR symbol None
15% Text message
< flashes (0.5 Hz) OFF SCR symbol None
10% Text message
< 5% flashes (0.5 Hz) Continuous light SCR symbol None
Acoustic signal Text message
Acoustic signal
< 5% ≥ 10 min flashes (1 Hz) Continuous light SCR symbol Stage 1
Acoustic signal
< 5% ≥ 15 min flashes (2 Hz) Flashing SCR symbol Stage 1
Acoustic signal
< 5% ≥ 20 min flashes (2 Hz) Flashing SCR symbol Stage 2
Acoustic signal
36 © 08/2017
Catalytic converter efficiency/Adblue® quality
If the catalytic converter efficiency (conversion rate) is too low, warnings are sent to the SCR function lamp or optionally to the CAN display despite previous refuelling. Warnings
are also given due to use of the wrong reduction agent.
Catalytic converter SCR function lamp Engine warning lamp DEUTZ CAN display Power reduction
efficiency/Adblue®
quality
too low Continuous light Continuous light SCR symbol Stage 1
Acoustic signal Text message After pre-warning time
Acoustic signal
too low Continuous light Flashing SCR symbol Stage 2
not remedied Acoustic signal Text message After pre-warning time
Acoustic signal
Manipulation
If the system detects a manipulated part or use of the wrong reduction agent, the performance is reduced. The performance is reduced in stages and depends on the motor
performance.
Manipulation SCR function lamp Engine warning lamp DEUTZ CAN display Power reduction
detected Continuous light Continuous light SCR symbol Stage 1
Acoustic signal
not remedied Continuous light Flashing SCR symbol Stage 2
Acoustic signal
© 08/2017 37
Operation Exhaust gas aftertreatment system

System fault
System faults may be faults of individual SCR components such as an implausible NOx or temperature sensor value. The performance is reduced if the SCR injection is impaired
by a system fault.
System fault SCR function lamp Engine warning lamp DEUTZ CAN display Power reduction
detected Continuous light Flashing SCR symbol None
Acoustic signal
detected ≥ 10min Continuous light Flashing SCR symbol Stage 2
Acoustic signal
Crystalisation
Crystalisation results when the engine's workload is too low, or its operating times are too short.
System fault Regeneration lamp Engine warning lamp DEUTZ CAN display Power reduction
detected flashes (0.5 Hz) OFF Text message None
Standstill regeneration Acoustic signal
required
detected flashes (0.5 Hz) Continuous light Text message Stage 1
required
detected flashes (3 Hz) Flashing Text message Stage 2
required
38 © 08/2017
Diesel oxidation catalyst (DOC)
The diesel oxidation catalytic converter has a catalytic
surface which is used to convert the pollutants in the
exhaust gas into harmless substances. Here, carbon
monoxides and unburned hydrocarbons are made to
react with oxygen and converted into carbon dioxide
and water. In addition, the nitrogen monoxides are
converted to nitrogen dioxides.
Temperatures > 250 °C are necessary for a high
degree of efficiency.
Diesel particle filter (DPF)
The combustion of diesel fuel results in soot, which is
separated in the diesel particle filter. This must be
regenerated as the contamination with soot increases.
That means that the soot in the diesel particle filter is
burned.
The regeneration is based on a continuous
regeneration process, which is activated as soon as
the exhaust temperature of 250 °C is exceeded at the
inlet of the exhaust gas aftertreatment system. The filter
contamination with soot is monitored continuously by
the engine control unit.
Regeneration
The passive particle filter system burns the soot in the
filter with the nitrogen oxide contained in the exhaust,
which is first oxidised in the DOC. This process takes
place continuously as soon as the exhaust
temperature exceeds 250 °C. The passive particle
filter system does not contain a burner. A prerequisite
for the passive continuous regeneration is having a
sufficient ratio of nitrogen oxides to soot in the raw
exhaust gas of the engine.
© 08/2017 39
Operation Passive regeneration

Normal operation There is a one or two-stage performance reduction This is displayed by a flashing regeneration lamp.
depending on the type of fault.
Under normal operating conditions (exhaust The standstill regeneration must be initiated by the
temperature > 250 °C), the filter contamination with Power reduction operator.
soot remains in a permissible range and no actions Stage 1 Torque reduction
are necessary. We recommend carrying out a necessary standstill
Stage 2 Torque reduction regeneration as quickly as possible, as otherwise the
The regeneration lamp is OFF. + Engine speed limitation diesel particle filter will continue to become
contaminated with soot.
Support mode Bridging of the power reduction
If the standstill regeneration is not carried out, the
During this operating state, an acoustic A separate emergency switch has been provided, in engine control unit will activate the specified engine
change occurs to the running of the engine. order to temporarily disable power reductions caused protection functions, depending on the contamination
by the EAT system. of the diesel particle filter.
If the operating conditions of the engine do not permit This function is available for a limited period and is Every standstill regeneration slightly dilutes the
any passive regeneration, the contamination of the expected to enable the user to move the machine to a lubricating oil with fuel. The number of standstill
diesel particle filter with soot will increase. safe location. regenerations is therefore monitored.
A throttle valve controlled via the engine control unit is This function is available for engines with power Implementation of the standstill regeneration
located in the combustion air inlet. This is used to reduction levels 1 and 2, in accordance with EU
increase the exhaust gas temperature for legislation, and with power reduction level 1, in The engine must be brought into a "safe state" for the
regeneration of the diesel particle filter, if this is not accordance with EPA legislation. regeneration:
reached during normal operation.
Standstill regeneration ● Shut down the engine on an open terrain at a safe
This can be the case if: distance to flammable objects.
Temperatures of approx. 600 °C occur on the ● Warm up the engine; the coolant temperature must
● The engine only has short operating times. exhaust pipe during regeneration. reach at least 75 °C.
● The engine workload is not high. A special engine operating state becomes
active during standstill regeneration and the ● Operate the engine in idling.
This process is automatically activated by the engine
machine is not allowed to be used during the ● The engine control unit now requires a signal
control unit, the operator does not need to perform any
active standstill regeneration. indicating that the unit is safely parked (stationary
actions.
Danger of burns● signal).
The regeneration lamp is OFF. ● This occurs independently of the application, for
If the support mode does not attain an adequate example by:
Power reduction reduction of the soot contamination, the filter will
continue to become contaminated with soot and a – Activating the parking brake.
If a serious fault occurs or a fault is not remedied, the standstill regeneration will be necessary. – Engaging a specified gear position in the
system reacts by reducing the engine performance.
gearbox.
40 © 08/2017
Passive regeneration Operation
● Operating the release button. If the standstill regeneration request is not observed
Position depends on application, see device and the diesel particle filter is overloaded to an
manual. impermissible level, then the diesel particle filter can
The regeneration lamp lights up continuously. only be regenerated via DEUTZ service.
Once the standstill regeneration has been released, Replacing the diesel particle filter
the engine automatically increases the speed level. It may be necessary to replace the diesel particle filter
Using the device during standstill regeneration is after a high filter running time as non-combustible
prohibited. residues accumulate in the diesel particle filter - so-
called ash.
The regeneration lasts 35 to 40 minutes on average.
If the ash loading goes beyond a certain level, this will
The standstill regeneration can be interrupted at any be indicated by the ash lamp.
time by pressing the regeneration button again or by
removing the regeneration release. The diesel particle filter needs to be replaced.
Using the device during standstill regeneration also The machine can operate normally until the
leads to it being interrupted. replacement is carried out by the service.
The request for standstill regeneration remains until it The time interval between two regeneration requests
is completed without interruption. is shortened in proportion to the run time.
Certain engine faults lead to excessive carbon Please contact your DEUTZ partner.
emissions from the engine which cannot be seen due DEUTZ particle filters come with a catalysing coating,
to the diesel particle filter. so require a special cleaning procedure to prevent
In such cases, the diesel particle filter can be loaded damage to the coating. The DEUTZ filter replacement
very quickly, among other things, to a level which no programme guarantees that the filter medium is
longer allows a standstill regeneration by the operator. properly cleaned, and the medium fully functions and
performs as if it were a new part!
Very short intervals between two standstill
regenerations (<10 hours) can be an indication of
such a defect.
Please contact the DEUTZ service.
The regeneration lamp goes out when regeneration
has been successfully completed.
© 08/2017 41
Operation Passive regeneration

Display of the regeneration control
The display and monitoring of the exhaust aftertreatment system can be executed either with pilot lights or with a CAN interface and a corresponding display, depending on the
engine version.
Instruments/symbols Power reduction Remark
Regeneration lamp Engine warning lamp Ash lamp

OFF OFF OFF Normal operation
OFF OFF OFF Support mode
flashes (0.5 Hz) OFF OFF Standstill regeneration required
Approval by the operator required
flashes (0.5 Hz) Continuous light OFF Stage 1 Standstill regeneration required
Approval by the operator required
flashes (3 Hz) Flashing OFF Stage 2 Please contact your DEUTZ partner
Continuous light OFF OFF Standstill regeneration
OFF OFF Continuous light 100% ash load
Please contact your DEUTZ partner
OFF OFF Flashing 105% ash load
OFF Continuous light Flashing Stage 1 110% ash load
42 © 08/2017
Stopping process Operation
Lag time
The control unit remains active for about

another 40 seconds to save the system data
(lag) and then switches off automatically.
For engines with an SCR system, this process
can take up to 2 minutes as the SCR lines
must be pumped until empty.
For this reason, the power supply to the
engine must not be suddenly interrupted by
the breaker.
Shutting down
Avoid switching off from full load

(coking/blockage of the remaining lubricating
oil in the turbocharger bearing housing). The
turbocharger's lube oil supply is no longer
ensured! This shortens the life of the
turbocharger.
Run the engine in low idling speed for
approximately one minute after relieving the
load.
● Move the key to position 0.

– P = gear position: park
– 0 = gear position: Shut down engine
– 1 = gear position: Ignition on
– 2 = gear position: Start engine
© 08/2017 43
Operating media Lubricating oil

General The lubricating oil quality has a considerable The following lubricating oils are permissible for the
influence on the life, efficiency and thus the economy engines in this operating manual:
Modern diesel engines place very high demands on of the engine. As a general principle, the better the
the lubricating oil used. The specific engine lubricating oil quality, the better these properties. Permissible quality class
performances increased constantly in recent years DEUTZ Other
lead to increased thermal stress of the lubricating oil. The lubricating oil viscosity describes the way the
In addition, the lubricating oil is subject to heavier lubricating oil flows, depending on the temperature. Engines with exhaust aftertreatment system
contamination due to reduced lubricating oil The lubricating oil viscosity only has a small influence DQC III LA * Please contact your DEUTZ partner
consumption volumes and increased lubricating oil and effect on the quality of the oil. DQC IV LA * or visit www.deutz.com
change intervals. For this reason it is necessary to * Sulphur content in the fuel
observe the requirements and recommendations Synthetic lubricating oils are used increasingly and
offer advantages. These lubricating oils have better < 15 mg/kg
described in this operating manual in order not to
shorten the life of the engine. temperature and oxidation stability, as well as
relatively low cold vicosity. Since some processes For low-ash engine oils released according to the
Lubricating oils always consist of a base lubricating oil which are relevant for determining the lubricating oil DQC system a corresponding note is given in the oil
and an additive package. The additives perform the change times are largely dependent on the oil quality release list.
most important tasks of a lubricating oil (e.g. wear (e.g. the infiltration of soot and other contamination),
DEUTZ lubricating oils DQC IV, low ash
protection, corrosion protection, neutralisation of acids the oil change time for synthetic lubricating oils may
DEUTZ Oil Rodon 10W40 Low SAPS
from combustion products, prevention of coke and soot not be increased in relation to the specifications on
deposits on the engine components). The properties lubricating oil change intervals. Container Ordering number:
of the base lubricating oil are also decisive for the 20 litre canister 0101 7976
quality of the product, e.g. with regard to the thermal Biodegradable lubricating oils may be used in
209 litre barrel 0101 7977
load. DEUTZ engines if they meet the requirements of this
operating manual. Lubricating oil change intervals
In principle, all engine lubricating oils of the same
specification can be mixed. Mixtures of engine Quality ● The intervals depend on:
lubricating oils should however be avoided because Lubricating oils are classified by DEUTZ according to – Lubricating oil quality
the worst properties of the mixture always dominate. their efficiency and quality class (DQC: DEUTZ Quality – Sulphur content in the fuel
The lubricating oils approved by DEUTZ AG have Class). the higher the quality class (DQC I, II, III, IV), the
more effective/the better quality the lubricating oil is. – Engine application type
been thoroughly tested for all engine applications. The
active ingredients they contain are compatible with – Number of standstill regenerations
The DQC quality classes are still to be extended by the
each other. Therefore, the use of additives for DQC-LA quality classes which include the modern, ● The lubricating oil replacement interval must be
lubricating oils is not permitted in DEUTZ engines. low-ash lubricating oils (LA = Low Ash). halved if at least one of the following conditions
applies:
The choice of luricating oil essentially depends on the – Ambient temperatures below -10 °C (14 °F) or
exhaust aftertreatment system. lubricating oil temperature below 60 °C
(140 °F).
44 © 08/2017
Lubricating oil Operating media
– Sulphur content in the diesel fuel less than 0.5
mass fraction.
● If the prescribed lubricating oil change intervals are
not reached within a year, the lubricating oil must
be changed at least once a year.
Viscosity
The ambient temperature at the installation site or in
the area of application of the engine is decisive for
selecting the right viscosity class. Too high a viscosity
can lead to starting difficulties, too low a viscosity can
endanger the lubricating effect and result in high
lubricating oil consumption. At ambient temperatures
below -40 °C, the lubricating oil must be pre-heated
(e.g. by storing the vehicle or the machine in a hall).
The viscosity is classified according to SAE. Oils
suitable for multiple ranges must always be used.
The prescribed lubricating oil quality must be

observed when selecting the viscosity class!
Depending on the ambient temperature we

recommend the following common viscosity classes.
© 08/2017 45
Operating media Fuel

Permissible fuels The certification measurements for compliance with
the legal emission limit values are carried out with the
In order to satisfy the exhaust gas legislation, diesel test fuels specified in the laws. These correspond to
engines that are equipped with an exhaust the diesel fuels described in this operating manual
aftertreatment system may only be operated with a according to EN 590 and ASTM D 975. With the other
sulphur-free diesel fuel. fuels described in this operating manual, no emission
The operational reliability and durability of the values are guaranteed.
individual exhaust aftertreatment technologies cannot The respective fuels prescribed by law must be used to
be assured upon failure to comply. comply with the national emission regulations (e.g.
sulphur content).
Exhaust gas after-treatment systems
SCR Selective catalytic reduction Please contact your DEUTZ partner or visit
DOC Diesel oxidation catalytic converter www.deutz.com
DPF Diesel particle filter Winter operation with diesel fuel
The following fuel specifications are approved: Special demands are placed on the cold behaviour
(temperature limit value of the filtrability) for winter
● Diesel fuels operation. Suitable fuels are available at fuel stations
– EN 590 in winter.
sulphur <10 mg/kg
For engines with common rail injection, the
– ASTM D 975 Grade 1-D S15
mixing of petroleum and adding of extra low
– ASTM D 975 grade 2-D S15 additives is not permissible.
sulphur <15 mg/kg
● Light heating oils At low ambient temperatures paraffin discharges can
lead to blockages in the fuel system and cause
– In EN 590 quality operating faults. Winter diesel fuel must be used at
sulphur <10 mg/kg ambient temperatures below 0 °C (up to -20 °C) (this
The warranty is excluded when using other fuels which is offered at fuel stations in good time before the start
do not meet the requirements of this operation of winter).
manual.
● Special diesel fuels can be used for arctic climates
up to -44 C.
46 © 08/2017
Coolant Operating media
General The water must be conditioned if it deviates from the Products released are recorded according to the
analysis values. following DEUTZ cooling system protection
Never operate the engine without coolant, not specifications.
even briefly! ● pH value too low:
Add diluted caustic soda or potassium soda. It is DEUTZ cooling system corrosion protection agent
advisable to make small test mixtures. Specifications Remarks
In liquid-cooled engines, the coolant must be
conditioned and monitored, otherwise the engine ● Total hardness too high: DQC CA-14 siliceous on the basis of MEG
could be damaged by: DQC CB-14 free of silicates on the basis of
Mixing with softened water (pH neutralized
organic acids (OAT) and MEG
● corrosion condensate or water softened by ion exchanger).
DQC CC-14 free of silicates on the basis of
● cavitation ● Chlorides and/or sulphates too high: organic acids (OAT) and MEG
● freezing Mixing with softened water (pH neutralized
● overheating condensate or water softened by ion exchanger). DEUTZ cooling system corrosion protection agent
Container Ordering number:
Water quality Cooling system protectants
5 litre canister 0101 7990
The right water quality is important for conditioning the Health damaging nitrous amines form when 20 litre canister 0101 7991
coolant. Clear, clean water within the following nitrite-based cooling system corrosion 210 litre barrel 0101 7992
analysis values should always be used: protection agents are mixed with amine-
based agents! The DEUTZ cooling system protection agent
Analysis values min max ASTM corresponds to the quality class DEUTZ DQC CB-14
ph value 6.5 8.5 D 1293 Cooling system corrosion protection agents
must be disposed of in an environmentally This cooling system corrosion protection agent is free
Chlorine (Cl) [mg/l] - 100 D 512
friendly way. from nitrite, amine and phosphate and is adapted to
D 4327
Observe the notes on the safety data sheet. the materials in our engines. Order from your DEUTZ
Sulphate (SO 4) [mg/l] - 100 D 516 partner.
Total hardness [mmol/l] 3.56 D 1126 The coolant is conditioned for liquid-cooled DEUTZ If the DEUTZ cooling system corrosion protection
(CaCO 3) 356 compact engines by mixing an antifreeze with agent is not available please contact your DEUTZ
corrosion protection inhibitors on an ethylene-glycol partner or visit www.deutz.com.
[°dGH] 20.0 - base with the water.
[°e] 25.0 - The cooling system must be monitored regularly. This
[°fH] 35.6 also includes checking the coolant system corrosion
protection agent concentration in addition to checking
Specifications of the water quality are made by the the coolant level.
local water board.
© 08/2017 47
Operating media Coolant

The inspection of the concentration of cooling system
protectant can be carried out with standard testing
devices (e.g. refractometers).
Cooling system Water Cold

corrosion percentage protection
protection agent up to
percentage
min. 35 % 65 % -22 °C
40 % 60 % -28 °C
45 % 55 % -35 °C
max. 50 % 50 % -41 °C
At temperatures below -41 °C, please contact your

responsible DEUTZ partner.
It is possible to use other cooling system corrosion
protection agents (e.g. chemical corrosion protection
agents) in exceptional cases. Consult your DEUTZ
partner.
48 © 08/2017
SCR reduction agent Operating media
AdBlue® (SCR reducing agent) It crystallises at -11 °C and at over +35°C a hydrolysis
reaction is initiated, i.e. it begins to slowly release
AdBlue® is known by different names ammonia and carbon dioxide.
depending on the region:
in the USA as DEF (Diesel Exhaust Fluid), in Direct sunlight on exposed storage containers must
Brazil as ARLA32. always be avoided.
The technical designation is AUS32. Barrels must not be stored for longer than one year!
AdBlue® is a registered trademark of the
Verband der Automobilindustrie e.V (VDA - Ensure that the materials and storage containers used
German Association of the Automotive are resistant to AdBlue®.
Industry).
AdBlue® freezes below -11°C ambient temperature.
Protective gloves and goggles must be worn It is necessary to preheat the SCR system at ambient
when handling AdBlue®. temperatures below -11 °C.
Do not swallow.
Ensure sufficient ventilation. AdBlue® SCR tank
Pay attention to cleanliness. Container Ordering number:
Residues of AdBlue® must be disposed of in The SCR tank may only be filled with AdBlue®. Filling
an environmentally friendly manner. 10 litre canister 0101 7982 with other media can lead to destruction of the system.
Observe the notes on the safety data sheet. 210 litre barrel 0101 7983
In this case the metering pump must be replaced.
Exhaust gas after-treatment systems AdBlue® should not remain in the tank for longer than
SCR Selective catalytic reduction 4 months.
AdBlue® is a highly-pure, aqueous, 32.5% urea This must be documented.
solution which is used as an NOX reduction agent for
SCR exhaust aftertreatment in vehicles with diesel Empty and clean the SCR tank when
engines. decommissioning.
The product is designated as AdBlue® or AUS 32 Please contact your DEUTZ partner
(AUS: Aqueous Urea Solution) and must correspond or see www.deutz.com
to the DIN 70070, ISO 22241-1 or ATSTM D 7821.
The length of time that AdBlue® can be kept without
losing quality depends on the conditions of its storage.
© 08/2017 49
Maintenance Maintenance schedule

Assignment of the DEUTZ maintenance and service schedules to the maintenance intervals
Routine maintenance work plan

TCD 4.1 L4 / TCD 6.1 L6 / TCD 6.1 L6
Stage Activity To be performed by: Maintenance interval every ....... operating hours (oh)
E10 Initial commissioning Authorised qualified personnel When commissioning new or overhauled engines
E20 Daily inspection Operator 1x daily or every 10 oh in continuous operation
1) 2) 4)
E30 Maintenance Qualified personnel 500
4)
E40 Extended maintenance I 1,000
4)
E50 Extended maintenance II Authorised qualified personnel 2,000
4)
E55 Extended maintenance III 4,000
3) 4)
E60 Intermediate overhaul 6,000
4) 5)
E70 Major overhaul 7,000
1)
The lubricating oil load may be high depending on the application. The lubricating oil change interval must be halved here 44.
2)
Specification for lubricating oil change interval, based on lubricating oil quality DQC III.
3)
Specification for cooling system protective agent change interval, on the basis of the cooling system protective agent specification DQC CB-14 and DQC CC-14.
4)
The display of the operating hours should be ensured by the device manufacturer. The engine operating hours are recorded by the control unit. Enquiry via the CAN bus
and display in a display or creation/display via electromechanical counter.
5)
The best time for a general overhaul depends to a great extent on the load, application and ambient conditions and the care and maintenance of the engine during the
operating time.
Your DEUTZ partner will advise you on determining the best time for a general overhaul.
50 © 08/2017
Maintenance schedule Maintenance
Maintenance measures
Stage Activity Measure

E10 The measures are described in chapter 3.
E20 Check Lubricating oil level (refill when necessary) 53
Cooling system protective agent level (refill when necessary)
Check engine for tightness (visual check for leakage)
Exhaust system including exhaust aftertreatment components for leaks
Suction air filter/dry air filter (if available maintain according to maintenance pointer)
Emptying of the water tank in the fuel pre-filter
E30 Check V-belts
Cooling system protective agent (additive concentration) 61
Intake air pipes for damage 63
Renew Lube oil A lube oil application/change strategy adapted optimally to the individual engine application type can be created, for example,
with the DEUTZ oil diagnosis. Ask your DEUTZ partner 53
Lubricating oil filter 53
E40 Check C-intercooler cooler inlet area (drain lube oil/condensation)
battery and cable connections 71
Cold starting device
Engine mounting (tighten if necessary, renew if damaged)
Fastenings, hose connections/clips (renew if damaged)
V-rib belt and tensioning pulley 65
Renew Fuel filter 56
Fuel pre-filter 56
Dry air filter 63
V-belts 65
SCR-feed pump filter cartridge 56
E50 Set Valve clearance 67
E55 Renew V-rib belt and tensioning pulley 65
© 08/2017 51
Maintenance Maintenance schedule

Stage Activity Measure
E60 Renew Crankcase ventilation
Cooling system protective agent 61
Clean Exhaust gas turbocharger compressor inlet
annually Check Engine monitor, warning system To be maintained by authorised service personnel only!
Renew Fuel filter 56
Fuel pre-filter 56
Lubricating oil 53
Lubricating oil filter 53
Every 2 Renew Dry air filter 63
years V-belts 65
Every 3 Renew SCR-feed pump filter cartridge 56
years
Every 4 Renew Cooling system protective agent 61
years
Status Change Dry air filter (if available maintain according to maintenance pointer) 63
dependent Diesel particle filter, the required exchange is displayed by the ash lamp or via an electronic display, depending on the engine version
(see DEUTZ exchange programme
Empty Fuel pre-filter with water trap. If the warning system is activated (lamp/horn), the water trap bowl must be emptied immediately 56
Maintenance diagram
A self-adhesive maintenance diagram is provided with every engine. This should be stuck to the engine or device in a prominent position.
Ordering number: 0312 4669 (TCD 4.1 L4 / TCD 6.1 L6 / TTCD 6.1 L6)
52 © 08/2017
Lubricating oil system Service and maintenance work
Specifications when working on the lubricating oil ● The lubricating oil level must always be between
system MIN- and MAX-1 markings! If necessary, fill up to
MAX-marking.
Do not work on the running engine!
Smoking and naked lights are prohibited! Changing the lubricating oil
Be careful with hot lubricating oil. Danger of ● Run the engine warm (lubricating oil temperature >
scalding! 80 °C).
Ensure the highest degree of cleanliness ● Position the engine or vehicle so as to be level.
when working on the lubricating oil system. ● Shut down engine
Carefully clean the area around the ● Position a collecting vessel under the lubricating oil
components concerned. Blow wet parts dry drain plug .
with compressed air.
Observe safety regulations and national ● Unscrew the lubricating oil drain plug, drain the
regulations when working with lube oils! lubricating oil.
Dispose of leaking lube oil and filter elements Checking the lubricating oil level. – In the case of agricultural technology engines
according to regulations. Do not allow used with a separate oil pan, both oil drain plugs
lubricating oil to seep into the ground. Lack of lube oil or overfilling lead to engine must be unscrewed.
Do a trial run after all work. Pay attention to damage. ● Turn in and tighten lubricating oil drain plug fitted
leakage and lube oil pressure and then The lubricating oil level may only be checked with new sealing ring.
check the engine lube oil level. when the engine is horizontal and switched Tightening torque:
off.
Only check lubricating oil level whilst warm, 5 55 Nm
minutes after shutting down.
● Fill in lubricating oil.
Be careful with hot lubricating oil. Danger of – Quality/viscosity information 44
scalding! – Filling quantity 83
Do not pull out the dipstick while the engine is
running. Danger of injury! ● Run the engine warm (lubricating oil temperature >
80 °C).
● Pull out the lubricating oil dipstick and wipe off with ● Position the engine or vehicle so as to be level.
a lint-free, clean cloth.
● Check lubricating oil level, if necessary re-fill
● Insert the lubricating oil dipstick as far as it goes.
● Remove the lubricating oil dipstick and read the
lubricating oil level.
© 08/2017 53
Service and maintenance work Lubricating oil system
Change lubricating oil filter ● Oil the seal of the new DEUTZ original spare filter
lightly.
Filter may never be pre-filled. Danger of ● Screw on new filter by hand until the gasket is
soiling! touching and tighten.
Tightening torque:
● Loosen and unscrew filter with tool (order no.:
0189 9142) 15 Nm - 17 Nm
● Collect escaping lube oil.
● Clean the sealing surface of the filter carrier with a
clean, lint-free cloth.
54 © 08/2017
Lubricating oil system Service and maintenance work
Replace lubricating oil filter cartridge ● Collect escaping lube oil. ● Replace gasket and oil lightly.
1 Cover ● Bend the filter cartridge in the collecting container ● Press new filter cartridge into bracket and place
slightly to the side until the cartridge comes out of them carefully into the guide.
2 Sealing ring the bracket. ● Screw the cover clockwise until tight.
3 Housing ● Clean the parts. Tightening torque:
4 Guide
5 Filter cartridge 25 Nm
6 Clamp
Filter may never be pre-filled. Danger of

soiling!
● Shut down engine

● Loosen cover by turning 2-3 times and wait for 30
seconds.
● Unscrew cover with filter cartridge anti-clockwise.
● Loosen the filter cartridge carefully out of the guide
in the housing and upwards.
© 08/2017 55
Service and maintenance work Fuel system

Specifications when working on the fuel system Clean and dry the engine and engine
compartment thoroughly before beginning
Engine must be switched off! work.
Smoking and naked lights are prohibited! Areas of the engine compartment from which
No injection/high pressure pipes may be dirt could be loosened must be covered with
disconnected while the engine is running. a fresh, clean foil.
Careful with hot fuel. Work on the fuel system may only be carried
Ensure the highest degree of cleanliness out in an absolutely clean environment.
when refuelling and working on the fuel Contamination of the air such as dirt, dust,
system. moisture etc. must be avoided.
Carefully clean the area around the
components concerned. Blow wet parts dry
with compressed air.
Observe safety regulations and national
regulations when working with fuels.
Dispose of leaking fuel and filter elements
Replace fuel change filter
properly. Do not allow fuel to seep into the
ground. Filter may never be pre-filled. Danger of
After all works on the fuel system, the system soiling!
should be vented, a trial run performed and
the tightness checked.
It is necessary to vent the fuel system when ● Loosen and unscrew filter with tool (order no.:
recommissioning, following maintenance 0189 9142).
work or if the tank has been completely ● Collect escaping fuel.
emptied.
● Clean the sealing surface of the filter carrier with a
clean, lint-free cloth.
Additional venting of the fuel system by a 5-
minute trial run on no-load or low load is
absolutely essential.
Pay attention to utmost cleanliness due to the
high production accuracy of the system!
The fuel system must be tight and closed.
Make a visual inspection for leaks/damage in
the system.
56 © 08/2017
Fuel system Service and maintenance work
● Lightly wet the seal of the new DEUTZ original Replace fuel filter cartridge
changeable filter with fuel.
● Screw on new filter by hand until the gasket is Filter may never be pre-filled. Danger of
touching. soiling!
Tightening torque:
10 Nm - 12 Nm ● Cover
● Sealing ring
● Vent the fuel system.
● Housing
● Guide
● Filter cartridge
● Clamp
© 08/2017 57
Service and maintenance work Fuel system
● Collect escaping fuel. ● Replace gasket and oil lightly. Change/vent fuel pre-filter
● Bend the filter cartridge in the collecting container ● Press new filter cartridge into bracket and place 1 Venting screw
slightly to the side until the cartridge comes out of them carefully into the guide.
the bracket. 2 Fuel supply to the fuel supply pump.
● Screw the cover clockwise until tight.
● Clean the parts. 3 Manual pump for venting
Tightening torque:
4 Electrical connection for water level sensor
25 Nm 5 Drain plug
6 Filter cartridge
7 Fuel supply from the fuel tank.
Empty water tank

● Place suitable collecting containers underneath.
● Electrical connection
– Disconnect cable connections.
● Loosen drain plug.
● Drain fluid until pure diesel fuel runs out.
58 © 08/2017
Fuel system Service and maintenance work
● Mount drain plug. ● Open the fuel shutoff tap and vent the fuel system,
Tightening torque: see venting the fuel system.
1.6 Nm ± 0.3 Nm Vent the fuel system
● Electrical connection ● Loosen vent screw.

– Connect cable connections. ● Unlock the bayonet connection of the fuel supply
pump by pressing upwards and simultaneously
Change the fuel pre-filter turning anticlockwise. The pump piston is now
pressed out through the spring.
● Pump until no more air escapes at the vent screw.
● Shut off the fuel supply to the engine (with high
lying tank). ● Tighten vent screw.
● Place suitable collecting containers underneath. Tightening torque:
● Electrical connection 1.6 Nm ± 0.3 Nm
– Disconnect cable connections. ● Keep pumping until a very strong resistance can
● Loosen drain plug and drain liquid. be felt and the pumping only progresses very
● Disassemble filter insert. slowly.
● Clean any dirt off the sealing surfaces of the new ● Lock the bayonet connection of the fuel supply
filter cartridge and opposite side of filter head. pump by pressing upwards and simultaneously
turning clockwise.
● Wet the sealing surfaces of the filter cartridge
slightly with fuel and screw back on to the filter ● Start the engine and operate it for approx.
head, clockwise. 5 minutes in idling mode or at low load. Check the
Tightening torque: pre-filter for leaks while doing this.
17 Nm - 18 Nm
● Mount drain plug.
Tightening torque:
1.6 Nm ± 0.3 Nm
– Connect cable connections.
© 08/2017 59
Service and maintenance work SCR (Selective Catalytic Reduction)
Change the filter cartridge of the SCR supply pump ● Mount cover.
1 Cover Tightening torque:
2 Compensation body 22.5 Nm ±2.5 Nm
3 Filter cartridge ● Electrical connection
Protective gloves must be worn when working – Connect cable connections.
with components of the SCR system. ● Start.
Pay attention to cleanliness.

– Disconnect cable connections.
● Place suitable collecting containers underneath.
● Remove cover.
– Socket wrench insert 27 mm
● Pull out filter insert and compensation body.
● Insert new filter insert with compensation body.
60 © 08/2017
Cooling system Service and maintenance work
Specifications when working on the cooling system
Danger of scalding from hot coolant!

Cooling system under pressure! Only open
the cap when cool!
The coolant must have a prescribed
concentration of cooling system corrosion
protection agent!
Observe safety regulations and national
specifications when handling cooling media.
Observe the manufacturer's specifications for
an external cooler.
Dispose of leaking liquids properly and do
not allow them to seep into the ground.
Order coolant corrosion protection agent
from your DEUTZ partner.
Check coolant additive concentration Emptying the cooling system
Never operate the engine without coolant, not
even briefly! ● Open the cooling system cap (1) carefully. ● Open the cooling system cap (1) carefully.
Checking the coolant level with an external cooler ● Check the coolant additive mixing ratio in the ● Place suitable collecting containers underneath.
cooler/compensation tank (2) with a conventional ● Remove the locking screw (1) in the crankcase.
● Fill in new coolant and vent the system according to freeze protection measuring instrument (1) (e.g.
the specifications of the cooling system hydrometer, refractometer). 47. ● Drain the coolant.
manufacturer. The corresponding test device can be ordered from ● Insert screw again with sealant.
● Open the cooling system cap (1) carefully. your DEUTZ partner under the order no.: 0293 7499. ● Close the cooling system sealing cover.
● The coolant level must always be between the MIN
and MAX marks of the compensation tank! If
necessary, fill up to MAX-marking.
© 08/2017 61
Service and maintenance work Cooling system

● Check coolant level in the cooled engine and top
up to the MAX mark or filling level on the
compensation tank if necessary.
Fill and ventilate cooling system
Danger of scalding from hot coolant!

Cooling system under pressure! Only open
the cap when cool!
● Open the cooling system cap (1) carefully.

● Loosen the cooler venting screw if necessary.
● Fill coolant up to the max. mark or filling limit.
● Switch on any available heating and set to the
highest level so that the heating circuit is filled and
vented.
● Close the cooling system sealing cover.
● Close the cooler venting screw if necessary.
● Run engine up to operating temperature (opening
temperature of the thermostat).
62 © 08/2017
Suction system Service and maintenance work
Regulations for working on the intake system Renewing the safety cartridge of the dry air filter
Do not work on the running engine! Never clean the safety cartridge (4).
Ensure the highest degree of cleanliness ● Renew the safety cartridge (4) at the interval
when working on the intake system, close specified in the maintenance schedule.
intake openings if necessary. ● To do this:
Dispose of old filter elements properly. – Unscrew hexagon nut (5), pull out safety
cartridge (4).
– Insert new safety cartridge, screw on hexagonal
nut.
● Insert filter element (3), mount filter hood (2) and fix
with clamping yoke (1).
Maintaining the dry air filter
Do not clean the filter element (3) with petrol

or hot liquids!
Renew damaged filter elements.
● Maintain the filter element (3) according to the

interval in the maintenance schedule.
● Lift up the clamping yoke (1).
● Remove the filter hood (2) and pull out the filter
element (3).
● Filter element (3):
– blow out with dry compressed air (max. 5 bar)
from the inside to the outside if soiling is only
slight,
– renew if heavily soiled.
© 08/2017 63
Service and maintenance work Suction system
Maintenance indicators for dry air filter Clean the dry air filter dust discharge valve.
● The dry air filter is maintained according to a ● Empty the dust discharge valve (1) by pressing
maintenance indicator or service gauge. together the discharge slit.
● Maintenance is necessary when: ● Remove any stuck on dust residues by squeezing
– the yellow indicator light of the maintenance the upper area of the valve.
switch illuminates when the engine is running. ● Clean the discharge slit.
– the red field (1) of the maintenance indicator is
fully visible.
● After completion of the maintenance work push the
reset button on the service gauge. The service
gauge is ready for operation again.
64 © 08/2017
Belt drives Service and maintenance work
Checking the belt drive
Only carry out work on the belt drive with the

engine at a standstill!
After repairs: Check that all protective
equipment is mounted and all tools have
been removed from the engine.
● Check the entire belt drive visually for damage.

● Renew damaged parts.
● Remount protective devices if necessary.
● Pay attention to correct fit of new belts, check the
tension after running for 15 minutes.
Replace V-rib belt Renewing the V-belt

1 Tension pulley 1 Screw
2 Retaining pin 2 Screw
3 Assembly bore 3 Screw
4 Setting screw
● Press tensioning roller with socket wrench in the
direction of the arrow until a retaining pin can be ● Loosen all screws and lock nuts.
fixed in the assembly bore. The V-ribbed belt is
now tension free. ● Move the air-conditioning system compressor over
the setting screw in direction (B) until the V-belt is
● First pull the V-ribbed belt off the smallest roller or slack.
off the tensioning roller.
● Remove belt and fit new one.
● Mount new V-ribbed belt.
● Move the air-conditioning system compressor over
● Retain tensioning pulley using the pin wrench and the setting screw in direction (A) until the V-belt has
remove the holding pin. attained the correct tension.
● Tension V-ribbed belt using the tensioning roller ● Check belt tension.
and socket wrench. Check whether the V-ribbed
belt is correctly in its guide. ● Retighten screws and lock nuts.
– Screw (1) 30 Nm
© 08/2017 65
Service and maintenance work Belt drives

– Screw (2) 30Nm
– Screw (3) 42 Nm
Checking V-belt tensioning

● Lower indicator arm (1) into the measuring device.
● Place guide (3) between two belt pulleys on the V-
belt (2). The stop must be at the side.
● Press the button (4) at right angles to the V-belt (2)
evenly until you hear or feel the spring snap in.
● Lift the measuring device carefully without altering
the position of the indicator arm (1).
● Read the measured value at the point of
intersection (arrow), scale (5) and indicator arm
(1).
● Retighten and repeat the measurement if
necessary.
Tool
The v-belt tension measurement device (order no.:
0189 9062) is available to order from your DEUTZ
partner.
66 © 08/2017
Adjustment work Service and maintenance work
Check valve clearance, adjust if necessary
● Let the engine cool down for at least 30 minutes
before setting the valve clearance: Lubricating oil
temperature below 80 °C.
● Disassemble electric line at the injectors.
● Remove the cylinder head cowling.
● Place turning gear over fastening screws of the belt
pulleys.
● Turn the crankcase until reaching valve overlap.
Outlet valve is not yet closed, inlet valve begins to
open.
The cylinders to be set can be seen in the setting
schematic. Set the valve clearance ● Turn rotation angle disc anticlockwise until
TCD 4.1 L4 reaching the specified rotation angle:
1 Lock nut
● Secure the rotation angle disc against twisting.
Valve overlap Set 2 Setting screw
● Tighten lock nut.
1 4 3 Rotation angle disc
Tightening torque:
3 2 4 Socket wrench insert
4 1 5 Magnet 20 Nm
2 3 ● Now adjust the two other valves at the rocker arm,
Valve clearance as described above.
TCD 6.1 L6 TCD 4.1 L4 IN Inlet valve 75° ± 15° ● Perform the setting procedure on every cylinder.
TCD 6.1 L6 EX Outlet valve 120° ± 15°
Valve overlap Set ● Reassemble cylinder head cowling (if necessary,
TTCD 6.1 L6
1 6 with new seal) in reverse order of disassembly.
5 2 ● Fit the rotary angle disc with socket wrench inset on ● Tighten screws.
3 4 the setting screw.
Tightening torque:
6 1 ● Fix magnet of the rotation angle disc.
● Turn rotation angle disc clockwise to the stop 9 Nm
2 5
(rocker arm without clearance) and set the scale to
4 3
zero.
© 08/2017 67
Service and maintenance work Adjustment work

Tool
The rotary angle disc (order no.: 0189 9093) is
available to order from your DEUTZ partner.
68 © 08/2017
Adjustment work Service and maintenance work
Valve clearance setting schematic
● Crankshaft position 1
Turn crankshaft until both vaalves overlap on the
cylinder.
Outlet valve is not yet closed, inlet valve begins to
open.
Setblack marked valves.
Mark the respective rocker arm with chalk to check
the setting you have made.
● Crankshaft position 2
Turn the crankshaft one turn (360 °).
Setblack marked valves.
© 08/2017 69
Service and maintenance work Engine cleaning

Cleaning work Cleaning with cold cleaner
With all cleaning work it must be ensured that Spray●the●engine●with●cold●cleaner●and●leave●it●for

components are not damaged (e.g. bent about●10●minutes●to●take●effect.
cooler grille etc.). Spray●the●engine●clean●with●a●high●pressure●water
Cover electrical/electronic parts and jet.
connections to clean the engine (e.g. control Warm●up●the●engine●so●that●the●water●residues
units, generator, solenoid valves etc.). Do not evaporate.
aim water/steam jet directly at them. Run the
engine warm afterwards. Cleaning with a high pressure cleaner
Only carry out cleaning work on the engine Clean●the●engine●with●a●steam●jet●(maximum●spray

when it is not running! pressure●60●bar,●maximum●steam●temperature
Remove the engine cover and cooling air 90●°C,●distance●at●least●1m).
hood if applicable and replace after cleaning. Warm●up●engine●so●that●water●residues●evaporate.
The respective applicable environmental Al●
ways●clean●the●cooler●and●cooling●fins●from●the
regulations must be observed. exhaust●air●side●to●the●fresh●air●side.
General
The following causes of contamination make cleaning
the engine necessary:
● High dust content in the air
● Chaff and chopped straw in the area of the engine
● Coolant leaks
● Lubricating oil leakage
● Fuel●leaks
Be●cause●of●the●different●application●conditions,
cleaning●depends●on●the●degree●of●soiling.
Cleaning with compressed air
Blow● ing●dirt●off●or●out.●Always●blow●the●cooler●and
cooling●fins●from●the●exhaust●air●side●to●the●fresh●air
side.
70 ©●08/2017
Electrical system Service and maintenance work
Regulations regarding work on the electrical Fire, sparks, smoking and naked lights are
system prohibited!
Danger of acid burns! Wear protective gloves
Do not touch live parts, replace faulty and glasses! Avoid contact with skin and
indicator lamps immediately. clothing.
Danger of short circuit! Do not place tools on
top of the battery!
Pay attention to correct polarity of the
connections. Removing the battery
Cover electrical/electronic parts and
connections to clean the engine (e.g. control ● When clamping off the battery, always disconnect
units, generator, solenoid valves etc.). Do not the negative pole first. Otherwise there is a danger
aim water/steam jet directly at them. Warm up of short-circuiting.
the engine. ● Remove the fastenings and take out the battery.
Under no circumstances may the voltage be
tested by tapping against the earth cable. Installing the battery
During electrical welding work, the earthing
terminal of the welding device must be ● Insert new or charged battery and attach the
directly clamped to the part to be welded. fastenings.
Three-phase current generator: Do not ● Clean the terminals and battery poles with fine-
interrupt the connection between the battery, grained sandpaper.
generator and controller while the engine is
● When connecting, connect the plus pole first and
running.
then the minus pole. Otherwise there is a danger of
Battery short-circuiting.
● Make sure the terminals have a good contact.
When clamping off the battery, electronically Tighten the clamping screws by hand.
stored data may be lost. ● Grease the assembled terminals with an acid-free,
Keep the battery clean and dry. acid-resistant grease.
Make sure that the battery fits correctly and
tightly.
Dispose of old batteries in an environmentally
friendly way.
Danger of explosion! The gases released by

the battery are explosive!
© 08/2017 71
Faults Fault table

Faults and corrective measures
Faults Causes Measures

Engine does not start up or starts up Not disconnected (if possible) Check coupling
with difficulty Fuel tank empty Tanks
Fuel suction pipe blocked Check
Starting limit temperature not reached Check
Cold starting device Check/replace
Wrong SAE viscosity class of the engine lubricating oil Change lubricating oil
Fuel quality does not comply with operating manual Change the fuel
Battery defective or not charged Check battery
Cable connections to the starter loose or oxidised Check cable connections
Starter defective or pinion doesn't mesh Check starter
Air filter soiled/turbocharger defective Check/replace
Air in fuel system Vent the fuel system
Compression pressure too low Checking the compression pressure
Exhaust gas backpressure too high Check
High pressure pipe leaking Check/replace
High-pressure pump defective Check/replace
Engines starts up, but runs irregularly Exhaust gas backpressure too high Check
or misfires Compression pressure too low Checking the compression pressure
Cold starting device Check/replace
Air in fuel system Vent
Fuel filter contaminated Clean
Injector defective Change
Engine cable harness defective Check/replace
72 © 08/2017
Fault table Faults
Engine does not start and diagnostic Engine electronics prevents starting Check error according to error code and
lamp flashes eliminate error if necessary
Speed changes are possible and Engine electronics has detected a system error and activates an equivalent speed Check error according to error code and
diagnostic lamp lights up eliminate error if necessary
Engine gets too hot. Temperature Venting line to the coolant compensation tank blocked. Clean
warning system is activated Defective lubricating oil cooler Check/replace
Lubricating oil filter soiled on the air and/or lubricating oil side Change
Lubricating oil level too high Check lubricating oil level, if necessary drain
Lubricating oil pressure too low Fill up lubricating oil
Coolant heat exchanger soiled Clean
Defective coolant pump (torn or loose V-belt) Check whether torn or loose
Low coolant Fill up
Resistance in cooling system is too high / flow volume too low Check the cooling system
Fan / viscous coupling defective, V-belt torn or loose Check/change/tension
Charge air pipe leaking Check charge air line
Charge air pipe soiled Check/clean
Air filter maintenance indicator / service gauge defective Check/replace
Fan defective/V-rib belt torn or loose Check fan/V-belt, change if necessary
Exhaust gas backpressure too high Check
Throttle valve defective Check/replace
Coolant temperature transmitter Check/replace
Coolant thermostat defective Check/replace
Coolant cover defective Check/replace
© 08/2017 73
Faults Fault table

Engine lacks power Lubricating oil level too high Check lubricating oil level, if necessary drain
Exhaust gas recirculation, actuator defective Check/replace
Fuel suction temperature too high Check system
Air filter maintenance indicator / service gauge defective Check/replace
Fan defective/V-rib belt torn or loose Check fan/V-belt, change if necessary
Charge air pipe soiled Clean
Exhaust gas recirculation, actuator defective Check/replace
Exhaust gas backpressure too high Check/clean
Exhaust gas turbocharger defective Change
Engine performs poorly and Engine electronics reduce performance Please contact your DEUTZ partner
diagnostic lamp lights
Engine doesn't work on all cylinders High pressure pipe leaking Check/replace
Compression pressure too low Checking the compression pressure
Engine cable harness defective Check/replace
74 © 08/2017
Fault table Faults
Engine has no, or too little, lubricating Lubricating oil pressure too low Fill up lubricating oil
oil pressure Engine is tilted too far Check engine mounting / reduce inclination
Lubricating oil pressure sensor defective Check/replace
Lubricating oil control valve jammed Check/clean
Lubricating oil suction pipe blocked Check/clean
Engine lubricating oil consumption Lubricating oil level too high Check lubricating oil level, if necessary drain
too high Engine is tilted too far Check engine mounting / reduce inclination
Crankcase ventilation Check/replace
Valve shaft seals defective Check/replace
Piston rings worn Check/replace
Exhaust gas turbocharger defective Check/replace
Lubricating oil in the exhaust system Engine operated continuously with too low a load (< 20% - 30%) Check load factor
Engine emits blue smoke Lubricating oil level too high Check lubricating oil level, if necessary drain
Engine is tilted too far Check engine mounting / reduce inclination
Crankcase ventilation Check/replace
Piston rings worn Check/replace
© 08/2017 75
Faults Fault table

Engine emits white smoke Fuel quality does not comply with operating manual Change the fuel
Condensation Warm up engine so that water residues
evaporate
Coolant in the exhaust gas Check
Engine emits black smoke Diesel particle filter defective Check/replace
Fault in SCR system AdBlue® tank empty/display full Check tank sensor
SCR not working Check plug connections and lines at the supply
pump and injector
Check plugs and lines of supply pump, Nox
sensor and exhaust temperature sensor
SCR not working (cold) Lines frozen, clean lines, check heating
AdBlue® tank frozen, check heating
Frequent standstill regenerations Air filter soiled/turbocharger defective Check/replace
Differential pressure of flow meter defective Change
NOx sensor defective Change
Differential pressure sensor of diesel particulate filter is issuing an implausible signal Change
Differential pressure line added Clean
76 © 08/2017
Engine management Faults
Depending on the design of the monitoring functions, – The engine must be checked by a DEUTZ
the electronic engine control can protect the engine in partner.
certain problematical situations by monitoring – If a lamp lights steadily a monitored measuring
important limit values during operation and checking variable (e.g. coolant temperature, lubricating
the correct function of the system components. oil pressure) has left the permissible value
Depending on the seriousness of a recognised fault, range.
the engine can continue to operate with limitations, – Depending on the fault, the engine power may
during which the diagnostics lamp lights up be reduced by the electronic engine control to
continuously or indicates a serious system error by protect the engine.
flashing. In this case, the engine should be switched off ● Flashing
as soon as safely possible.
Serious error in system.
Diagnostics lamp
– Switch off prompt for the operator. Attention:
The diagnostics lamp is located in the vehicle drive Failure to do so will lead to loss of guarantee!
Engine protection function of the electronic engine stand. – Engine forced to run at low power to cool the
control The diagnostics lamp can release the following engine, with automatic shutdown if necessary.
1 Diagnosis button signals: – The engine has reached switch-off condition.
2 Diagnostics lamp ● Function test – The switch-off process has been accomplished.
3 Electronic engine control (EMR) – Ignition on, diagnostics lamp lights up for – There may be a start lock after engine stop.
approx. 2 seconds and then goes out. – The start lock is deactivated by turning off the
When all errors are rectified, the diagnostics – Check the diagnostics lamp if there is no system with the ignition key for approx. 30
lamp goes out. For some errors, it is reaction after switching on the ignition. seconds.
necessary to switch off the ignition, wait 30 – In order to avoid critical situations the power
seconds and only then switch back on the ● The lamp does not light up
reduction can be bypassed, automatic switch-off
ignition. – After the lamp test an extinguished lamp delayed or a start lock bypassed using the
The appropriate monitoring functions are indicates an error-free and trouble-free optional emergency key on the instrument
switched off when a sensor fails. Only the operating state within the scope of the control panel. This brief deactivation of the engine
sensor failure is documented in the error possibility. protection functions is logged in the control unit.
memory. ● Continuous light ● Please contact your service partner in case of
Error in system. malfunctions and spare parts inquiries. Our
specially trained personnel will ensure fast,
– Operation continued with restrictions. professional repairs using original DEUTZ spare
parts in case of damage.
© 08/2017 77
Faults Engine management

Diagnosis button
The diagnosis button allows the errors currently saved
in the error memory of the electronic engine control to
be visualised in the form of a flash code. The flash
codes permit:
● Errors that may occur can be classified.
● Clear display of the error as visual signal.
– The blink codes can only be interpreted by a
DEUTZ partner.
Use of the diagnostic key
The flash code displays all errors in the error memory,
this means active as well as passive ones.
Displaying system errors by blink code
The control unit must be switched off to start the
enquiry (ignition off). Following this, the diagnosis Example:
button should be pressed for approx. 1second during
the start (ignition on). 1 x short flash
The next error (i.e. the following one in the error 2 x long flash
memory) can then be displayed by pressing the 8 x short flash
diagnostic key again. If the last existing fault has been
shown the first fault will be shown again by pressing This flash code indicates a break or short circuit in the
the diagnosis button once more. wiring of the charge air temperature sensor. The
temporal sequence of the flash signals is shown in the
After the display of the error flash code, the diagnostics illustration.
lamp goes out for five seconds.
● The blink codes can only be interpreted by a
DEUTZ partner.
78 © 08/2017
Transport Transport and storage
Suspension equipment Mortal danger!

The engine may tip or crash down if
The transport devices mounted on this suspended incorrectly.
engine are adapted to the engine weight. If
the engine is transported with add-on ● The fastening attachment cannot be fixed securely
components, the transport devices must be above the centre of gravity (1).
designed accordingly.
● The fastening attachment can slip, the engine
● Only use the correct suspension equipment for swings backwards and forwards (1).
engine transportation. ● Too short a fastening attachment causes bending
● The suspension device (1) must be adjustable for torques in the transport device (2) and can
the engine's centre of gravity. damage it.
● Following transport/before commissioning the
engine: Remove the transport equipment (2).
© 08/2017 79
Transport and storage Engine corrosion protection

General Before operating a corrosion protected engine, the ● Wait for the end of the lag time of the EDC
corrosion protection must be removed. (Electronic Diesel Control).
Engines contain the following types of corrosion
protection: Exhaust gas aftertreatment system ● Repeat the process several times if necessary.
Please contact your DEUTZ partner if the fault cannot
● Internal corrosion protection Selective Catalytic Reduction (SCR) be remedied.
● External corrosion protection The SCR system can be taken out of operation for up Corrosion protection of engines which have already
to 4 months after completely shutting down (includes been in operation
Your DEUTZ partner has the right corrosion
all lag functions) and the following conditions:
protection agent for your needs.
Internal corrosion protection
● The vehicle or engine should be stored in a
The following measures for corrosion protection after covered place, e.g. garage or hall, for longer The internal corrosion protection is always effected by
taking the engine out of operation meet the shutdowns. wetting the walls with the corrosion protection agent by
requirements for 12 months corrosion protection. ● Completely fill the SCR tank. running the engine. The corrosion protection run can
be carried out once to protect the different systems.
● Evaporation of water as part of the AdBlue® must
The following corrosion protection work may only be
be avoided. Fuel system
carried out by persons familiar with it and instructed in
the potential dangers. ● Do not disconnect electrical or hydraulic ● Fill fuel tank with according to biodiesel-free fuel
connections. EN590 or ASTM D975 grade 1-D S15
A shorter corrosion duration is to be expected in case
● Maximum storage time at -40 ℃ to 40 ℃ 2 months. ● Perform a corrosion protection run with no load for
of deviation from the measures by exposure of the
corrosion protected engines or parts to unfavourable ● Maximum storage time at -40 ℃ to 25 °C 4 months. at least 5 minutes.
conditions (installation outdoors or storage in damp,
unventilated places) or damage to the corrosion If the shutdown time of 4 months mentioned above has Close the fuel/tank/supply line to the engine
protection coating. been exceeded, proceed as follows: so that the system is protected against dirt
and dust. Protect the electronics against
The engine corrosion protection must be checked ● Completely empty the SCR tank. moisture and corrosion.
about every 3 months by opening the covers. If ● Completely fill the SCR tank with new AdBlue®. Standstill times of longer than 4 weeks must
corrosion is detected, the corrosion protection should always be avoided with biodiesel.
be renewed. ● Replace the filter cartridge of the SCR supply pump
● Warm up the engine to operating temperature and Lubricating oil system
After completion of the corrosion protection work, the load so that pressure builds up and AdBlue® is
crank drive may no longer be turned in order to injected. ● Drain the lubricating oil from the engine at
prevent the corrosion protection agent from being operating temperature.
scraped off in the bearings, bearing liners and cylinder If a fault is detected:
liners. ● Shut down engine.
80 © 08/2017
Engine corrosion protection Transport and storage
● Fill the engine with preservation oil and perform a – Treated water Engine openings
corrosion protection run (together with corrosion – Corrosion protection agent with light antifreeze
protection run for the fuel system). For this, run the ● All engine openings must be fitted with airtight,
engine to reach a temperature of 60 °C, duration of ● The duration of the corrosion protection run and watertight covers to delay the evaporation
at least 5 minutes, so that all components of the the concentration of the corrosion protection agent processes of the corrosion protection agent.
lubricating oil system are wet, are specified by the manufacturer of the corrosion With installed air compressor, the suction and
or protection agent. pressure connection must be sealed by a cap.
wet all accessible components with preservation oil ● Then drain the coolant.
and pump preservation oil at a temperature of Air should be locked out to avoid ventilation of the
Intake air lines engine (chimney effect) for the suction from an air
around 60 °C through the engine until all bearings
and bearing liners are wet. ● Spray corrosion protection oil or preservation oil supply pipe.
● Clean the lubricating oil pan, cylinder head with into the intake air pipe. Storage and packing
rocker arms, valves, valve springs thoroughly with External corrosion protection
diesel fuel or cleaning agent. ● After being protected against corrosion, the engine
The engine must be cleaned thoroughly with cleaning must be stored in a dry, ventilated hall and suitably
Air compressor covered.
agent before external corrosion protection.
● If a compressor is installed, a corrosion protection The cover must lie loosely on the engine so that air
agent must be sprayed into the compressor suction Bare outside parts and surfaces can circulate around the engine to prevent
system after shutting down the engine until it condensation from forming. Use desiccant if
● Coat or spray all bare exterior parts and surfaces
emerges visibly from the pressure nozzle. necessary.
(e.g. flywheel, flange faces) with corrosion
Cooling system protection agent. Re-application of engine corrosion protection
● Depending on the series the engines are ● Under extreme conditions, e.g. sea transport or
military specifications, a long-term corrosion If the max. protection duration of the corrosion
equipped with a cooling air, cooling lubricating oil protection is reached or damaged corrosion protection
or coolant system (cooling water with cooling protection oil should be used.
is detected and the engine is to stay in storage, new
system protection agent). Rubber parts corrosion protection must be applied. The new
● In liquid-cooled engines, the coolant must be ● Rubber parts (e.g. muffs) which are not painted corrosion protection protects the engine or spare parts
drained and the cooling system cleaned must be rubbed with talcum powder. for another 12 months.
● Then carry out a corrosion protection run so that a Belt drives The new corrosion protection is applied in the same
coating forms on the inside surfaces of the cooling way as the initial corrosion protection with a corrosion
system. With a mixture consisting of: ● Disassemble V-belts and V-rib belts and store protection run. If a corrosion protection run is not
– Treated water packed. possible (engine is removed from the device or system
– Corrosion protection agent ● Spray V-belt pulleys and tension pulleys with for example), certain special conditions must be
corrosion protection agent. observed for application of new corrosion protection
or which are described below:
© 08/2017 81
Transport and storage Engine corrosion protection

Internal corrosion protection Removal of corrosion protection Corrosion protection agent / cleaning agent
Fuel system Removal of internal corrosion protection Please ask your DEUTZ partner for reference products
for the corrosion protection agents/cleaning agents to
● DEUTZ recommends using diesel fuel containing Fuel system be used which meet DEUTZ requirements.
polycyclic aromatic hydrocarbons ≤ 8.0 %(m/m), a
lubricity of ≤ 400 micrometers in the HFRR test (EN ● Fill the fuel tank and fuel system with the proper or see www.deutz.com
ISO 12156-1) and biodiesel (FAME) ≤ 0.1 %(V/V). fuel.
Pump fuel with a separate pump or a fuel hand Lubricating oil system
pump until the fuel system is full. Then drain the ● Fill the engine with lubricating oil via the oil filler
fuel mixture. neck.
Lubricating oil system Cooling system
● Press warm preservation oil (at approx. 60°C) into ● If the implemented corrosion protection agent is
the lubricating oil circuit with a separate pump, or compatible with the intended coolant system
with the prelubricating hand pump. Turn over the protection agent, this can be filled directly into the
engine by hand or with the electric turning gear so coolant system as specified.
that all bearings and bearing liners are wet. The ● If it is uncertain whether the implemented corrosion
engine can also be turned over with the starter protection agent is compatible with the coolant
without starting the engine. system protection agent, the cooling system should
● Remove the cylinder head cover and spray valves, be purged with fresh water for about 15 minutes
valve springs and rocker arms with preservation oil. before filling.
Cooling system Removal of corrosion protection from external
● The corrosion protection does not normally need to parts
be renewed up to 24 months. If necessary, the ● All areas and components coated with corrosion
coolant system can be filled with a mixture of protection agent must be washed off with distilled
corrosion protection agents and circulated by an fuel or a suitable cleaning agent.
external pump, so that a new coating can form on
the inside surfaces of the cooling system. ● Wash out grooves of V-belts if necessary.
● The duration of the corrosion protection run and ● Fit V-belts and V-rib belts according to
the concentration of the corrosion protection agent specifications.
are specified by the manufacturer of the corrosion ● Fill up the coolant.
protection agent.
● Then drain the coolant.
82 © 08/2017
Engine and setting data Technical data
General technical data
Engine type Unit TCD 4.1 L4 TCD 6.1 L6 TTCD 6.1 L6

Working principle Four-stroke diesel engine
Charging Turbocharger with charge air cooling
Type of cooling water-cooled
Cylinder arrangement in a row
Number of cylinders 4 6
Bore/stroke [mm] 101/126
Engine swept volume [cm 3] 4038 6057
Combustion method Direct injection
Injection system Deutz CommonRail (DCR)
Exhaust gas recirculation external
Exhaust aftertreatment Selective Catalytic Reduction
SCR
and
Diesel Particle Filter
DPF
Valves per cylinder 4
Valve clearance: Inlet/outlet [mm] 0.3 / 0.5
Setting with rotation angle disc [cm −3] 75° ±15° / 120° ±15°
Ignition sequence of the engine 1-5-3-6-2-4
Direction of rotation looking onto the flywheel left
Engine power according to ISO 3046 [kW] See engine rating plate
Speed (nominal speed) [rpm] See engine rating plate
Coolant volume (only engine content without cooler / hoses and pipes) ≈[l] 5.9 11.5 12
Permissible continuous coolant temperature [°C] max. 110
Temperature difference between coolant inlet/outlet [°C] 4-8
© 08/2017 83
Technical data Engine and setting data

Engine type Unit TCD 4.1 L4 TCD 6.1 L6 TTCD 6.1 L6
Start of thermostat opening [°C] 87
Thermostat fully open [°C] 102
Lube oil change volume (with filter)
≈[l] 11.5* 15.5* / 25.0* 25.0*
Industrial engines/Agricultural technology
Lube oil temperature in the lube oil pan, maximum [°C] 125
Lube oil pressure minimum (low idle speed, engine warm) [kPa/bar] 80/0.8
Permissible maximum combustion air temperature after charge air cooler [°C] 50
V-belt tension Pre-tighten/retighten
V-belts AVX 13 (width: 13 mm) [N] 650±50 / 400±50
V-rib belt tensioning Automatic tensioning spring-loaded clamping roller
Weight without cooling system according to DIN 70020-A
≈[kg] 400 / 450 621 / 641 680
Industrial engines/Agricultural technology
*specified lube oil filling volumes apply for standard versions. The lubricating oil filling volume may vary in engines which deviate from the standard, e.g. different lubricating oil
pan/lubricating oil dipstick variants and/or special inclined versions. The lubrication oil dipstick mark is always decisive
84 © 08/2017
Tools Technical data
Tool ordering
The special tools described in this chapter are
available to order from your DEUTZ partner.
Hexalobular tool kit V-belt tension meter

Ordering number: Ordering number:
0189 9092 0189 9062
Tool kit for loosening and tightening hexalobular Measuring device for testing the specified v-belt
screws. tension.
© 08/2017 85
Technical data Tools
Special wrench for loosening exchangeable filters Refractometer

Ordering number: Ordering number:
0189 9142 0293 7499
For loosening interchangeable filters. The following operating media can be evaluated with
this test device:
● Coolant
● Battery acid
● SCR reduction agent
86 © 08/2017
'(87=$*
6DOHV 6HUYLFH,QIRUPDWLRQ6\VWHPV
2WWRVWUD¡H
.¸OQ
*HUPDQ\
3KRQH
)D[
(PDLOLQIR#GHXW]FRP
ZZZGHXW]FRP
3ULQWHGLQ*HUPDQ\
$OOULJKWVUHVHUYHG
HQ
k
2ULJLQDORSHUDWLQJLQVWUXFWLRQV

MG5728

Uploaded by

Copyright:

Available Formats

MG5728

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MG5728

Uploaded by

Copyright:

Available Formats

Operating Manual

Please read this operating

You will find this symbol in all instructions of

CALIFORNIA PROPOSITION 65 WARNING

Engine exhaust, some of its constituents, and

The engine and the corresponding EAT

Engine description Model

The serial numbers of the exhaust aftertreatment

Serial numbers of the exhaust aftertreatment Cylinder numeration

Engine description Engine illustration

Engine description Engine illustration

Engine description Engine illustration

Engine description Lubricating oil plan

Engine description Coolant plan

Engine description Exhaust gas recirculation

Engine description Exhaust gas aftertreatment

Engine description Electrics/Electronics

Operation Ambient conditions

● Application at high altitude

Operation Initial commissioning

Operation Start process

If the engine fails to fire and the error lamp

Operation Operation monitoring

Instruments/symbols Designation Possible displays Measure

Coolant temperature Coolant temperature too high Switch off engine

SCR function lamp Continuous light Check AdBlue® filling level

Regeneration lamp Continuous light Initiate standstill regeneration 40

Operation Operation monitoring

Operation Exhaust gas aftertreatment system

Operation Exhaust gas aftertreatment system

Operation Passive regeneration

Operation Passive regeneration

Instruments/symbols Power reduction Remark

Regeneration lamp Engine warning lamp Ash lamp

The control unit remains active for about

Avoid switching off from full load

● Move the key to position 0.

Operating media Lubricating oil

The prescribed lubricating oil quality must be

Depending on the ambient temperature we

Operating media Fuel

Operating media Coolant

Cooling system Water Cold

At temperatures below -41 °C, please contact your

Maintenance Maintenance schedule

Routine maintenance work plan

Stage Activity Measure

Maintenance Maintenance schedule

Service and maintenance work Lubricating oil system

Filter may never be pre-filled. Danger of

● Shut down engine

Service and maintenance work Fuel system

Service and maintenance work Fuel system

Empty water tank

1.6 Nm ± 0.3 Nm Vent the fuel system

● Electrical connection ● Loosen vent screw.

Service and maintenance work SCR (Selective Catalytic Reduction)

● Shut down engine

Danger of scalding from hot coolant!

Service and maintenance work Cooling system