BYDT45C01 User Manual

Data Class: Confidential
BYD T45C01 pure electric truck
User Manual
Version/Revision: A/003
Commercial Vehicle Research Institute
February 22, 2022

BYD T45C01 Pure Electric Truck User Manual
foreword
You are welcome to choose BYD commercial vehicles. To help you use the vehicle correctly, please read this
manual carefully.
Special note: BYD Auto Industry Co., Ltd. recommends that you choose genuine spare parts. The use of non-pure spare parts to
replace or modify the vehicle will affect the performance of the vehicle, especially the safety and durability. Vehicle damage and
performance problems arising from this will not be covered under warranty. within the range. The structure of the high-voltage and low-
voltage circuits of the vehicle is complex, please do not disassemble the high-voltage circuits, low-voltage electronic components of the
vehicle, or install electrical appliances such as anti-theft devices and stereos. In addition, the modification of the vehicle may also
violate national laws and regulations and local government regulations. If you have any installation or modification needs, please
contact BYD sales and service personnel for confirmation.
In this manual, in the places marked with "Warm Reminder", "Caution", "Warning" and "Danger", you must be careful
to avoid the possibility of injury or damage according to the content of the reminder. Show:
Kind tips
* Refers to providing necessary additional
information.
Notice
* Indicates that failure to follow necessary operations or prohibited operations may cause the vehicle to be unsafe, etc.
hidden danger.
warn
* Indicates that failure to follow necessary operations or prohibited operations may cause general personal injury
damage or cause damage to the vehicle.
1
BYD T45C01 User Manual
Danger
* Indicates that failure to follow necessary operations or prohibited operations may result in serious personal injury
even lead to death.
202201 edition
The purpose of this manual is to help you use the product correctly. The pictures provided in this manual are schematic
diagrams and are for reference only.
Copyright by BYD Auto Industry Co., Ltd.
The right to modify the technical characteristics and content of this manual is reserved without any restriction or prior notice
Part or all of the manual may not be reproduced or copied without the written permission of BYD Auto Industry Co., Ltd.
2
Overview of BYD T45C01 pure electric truck
BYD T45C01 is a new generation of BYD logistics vehicle, equipped with a new self-developed high-tech, high-value cab, and passed the
European standard R29 crash certification, which is safer and more comfortable. Equipped with one -button start, knob shifting, electric air
conditioner, adjustable EBP driving mode, LCD instrument, large multimedia screen and many other economical and prac tical high-tech
configurations. The vehicle has a long cruising range and high operating efficiency, and can be widely used in urban commodity logistics such
as e-commerce, express delivery, moving, postal service, and cold chain.
Vehicle Safety
* Driving safety
Hydraulic front disc and rear drum braking, equipped with ABS anti-lock braking system.
* High voltage safety
The iron battery has been tested by high temperature, high pressure, impact and other experiments, and has excellent safety; the whole vehicle adopts
Design of two-wire system, leakage alarm device, connector anti-contact finger, etc.
* Security configuration
The whole vehicle is equipped with a front bumper, side and rear anti-collision beams; the battery management unit monitors the power at all times
battery to ensure that the battery has been working under normal conditions; the vehicle is equipped with a dry powder fire extinguisher.
Vehicle technical highlights
* Power battery
Equipped with BYD's self-developed iron battery power system with high energy density, high power density and high safety, the
vehicle has a power of 85 kWh and an optional power of 99 kWh, which meets the user's battery life requirements. BYD pure ele ctric truck
T45C01 is equipped with BYD's self-developed lithium iron phosphate battery with outstanding performance, safety and stability, to ensure the
stable, efficient and safe operation of the vehicle.
BYD is one of the few companies in China that has the R&D capability throughout the entire industrial chain from raw materials to
battery packs, and is the first company in the world to pass the safety certification of QC/T 743, UL1642 and UL2580; During the research and
development process, the "ferroelectricity" was frequently
3
"Pool" for extreme tests such as fire, short circuit, acupuncture, impact, high temperature, extrusion, and overcharge.
* Integrated bridge driver
Adopt integrated bridge drive mode, the maximum power of the motor is 145kw, and the maximum torque is
330N m. BYD creatively integrates the drive motor, automatic transmission and drive axle, with a compact structure, smooth dr ive, and
transmission efficiency of more than 95%, reducing vehicle energy consumption and operating costs. At the same time, when the vehicle
brakes and decelerates, the motor feeds back, which improves the vehicle cruising range and auxiliary braking, and improves driving safety.
* Battery management system
Using a distributed battery management system, it is safer and more reliable. The battery management system monitors the battery
temperature, voltage, and current information in real time, calculates the battery power, and ensures that the power battery is safely
discharged and charged.
* Battery thermal management system
Equipped with BYD's self-developed battery thermal management system. The cooling function ensures the power battery
Safety and extended service life, optional heating ensures that the vehicle starts normally at low temperature.
* Regenerative braking
When the vehicle brakes, the motor feeds back power, converts kinetic energy into electrical energy, and stores it into power.
Pool, improve driving safety and driving mileage.
* CAN bus
The whole vehicle is controlled through the CAN bus communication system to realize the intelligent management and maintenance of the whole vehicle.
It saves the wiring of t he whole vehicle and has t he characteristics of safety and reliability.
* Vehicle terminal
The vehicle is installed with an on-board terminal, which can monitor the status of the vehicle power battery, the status of the vehicle, and the position of the vehicle.
Record and store status information such as settings.
* Multimedia
4
Radio, PAD (optional), reversing image (optional), Bluetooth, navigation function (optional),
4G module, air conditioning panel and voice recognition (optional), etc.
* CP18B cab
The whole vehicle is equipped with a new-shaped cab independently developed by BYD, built by an international design master,
Wolfgang Egger, design director of BYD, which integrates traditional Chinese elements and European vehicle safety standards;
Brand new appearance, large field of view, large space, high waistline and integrated front face, perfect fusion of extreme aesthetics
and ergonomics;
High-tech configuration and exquisite interior, the perfect combination of appearance and practicality, quality and safety
The ultimate embodiment, allowing you to enjoy the sedan ride experience;
[New appearance] Break through the traditional design, the new cab, the appearance is strong, fashionable and beautiful, the
simplicity is sci-fi, with a sense of technology, the streamlined design has smaller wind resistance, and the super high value brings a different
kind of Visual enjoyment, family-oriented modeling to create brand recognition.
[Dynamic waistline] The overflowing high waistline runs through the entire cab, and the appearance is more tough
Strict;
[Highlight headlights] The newly developed angel eye headlights have a brightness of 65000cd, sharp edges and corners, full of
technology and a sense of security
[Integrated front face] The decorative glass and the front windshield are integrated into the front face, which is tough and powerful.
Come for luxurious visual enjoyment, full of technological futuristic sense
[Optional Electric Heated Rearview Mirror] Optional electric heated rearview mirror, no fear of cold and wind and rain, bring
The best vision for customers, ensuring driving safety, all the way forward regardless of the weather
[Hidden door handle] The hidden door handle, with the streamlined shape of the whole vehicle, is aggressive and domineering.
open the future
Vehicle comfort
* Hill assist + cruise control: start smoothly on steep slopes; release feet under appropriate conditions of cruise control;
Effectively reduce driving fatigue.
5
* Large-scale vacuum booster: The vehicle adopts a large-scale vacuum booster, which can effectively reduce the brake pedal force. The driver
can achieve higher braking performance with less force and relieve driving fatigue.
*Reversing image (optional): optional reversing image, the situation behind the car can be seen intuitively, even at night
It can also see the rear road conditions through infrared rays, reduce the rear blind spot, and improve the safety of the car;
*Adaptive ji tter suppression function: The whole vehicle is equipped with an adaptive jitter suppression function, which completes jitter
suppression within 0.5s, effectively dealing with complex road conditions such as flat roads, ramps, washboard roads, etc.
The driving experience is smoother;
* Large space: ultra-wide cab (120mm higher than competing products), supplemented by superior ergonomics
Engineering design, wide field of vision;
* One-button start: The first to introduce a one-button start system, simple and convenient operation, leading the trend; *Wrapped seat:
The passenger car-level wrapping seat with a sporty feeling, soft and moderate material,
The comfort can be adjusted according to different body types to effectively relieve driving fatigue;
* Intelligent rotating PAD (optional): 10.1-inch self-adaptive rotating and floating LCD touch PAD, which integrates massive APP applications
and intelligent voice control to improve the driver's driving experience;
* LCD instrument: 8-inch LCD instrument, simple and beautiful, comprehensive functions, rich display information,
Real-time monitoring of vehicle status;
*Knob shift: easy to operate, compact layout, while reducing cumbersome operations
The user has widened t he space in the cabin;
*Automatic air conditioning (optional): precise and comfortable temperature control, low noise
warm and comfortable;
* Multi-function steering wheel: It integrates multimedia control and cruise control functions.
Complete, not only easy to operate, but also effectively improve the driver's driving safety;
*EPB (optional): Electronic parking brake, which is more comfortable and easier to operate than the traditional mechanical handbrake
Fast, safe and reliable;
*EPS: Electric power steering, easy to operate and easy to maintain.
Vehicle Safety
6
* Battery safety: Power batteries designed and developed by BYD's entire industrial chain, from cells, batteries
In the process of research and development, the whole vehicle has undergone a series of extreme tests such as fire, water immersion,
short circuit, high temperature, extrusion, etc., thus ensuring the safety and stability of the power battery.
* Battery thermal management system: the industry's first thermal management system, standard battery liquid cooling, temperature control
The precise control ensures that the vehicle can operate stably and efficiently in various climatic environments.
Effectively ensure battery safety, and battery life is increased by more than 10%.
* High voltage safety: BYD independently developed an integrated controller with a waterproof rating of IP68.
And it has an active discharge function, which consumes the charge in the controller in a short time, so that it can quickly
Discharge, reduce maintenance waiting time, and ensure after-sales service safety. The whole vehicle adopts high-quality cables,
which have the advantages of anti-interference, connection error prevention, high-level protection, and can adapt to various harsh
working environments, ensuring the safety of drivers and after-sales service.
* High-strength cage body: It has the first brand-new development for the electric logistics market in China.
The high-strength cage body that has passed the European standard R29 crash certification has excellent safety performance.
* Braking safety: front disc and rear drum brake, fast braking response, good performance, and improve safety
Yes; equipped with a vacuum tank, the life of the vacuum pump is increased by 10%
vehicle economy
* EPB driving mode adjustable: the first in the industry to be equipped with EPB driving mode selection function,
Users can choose three different driving modes: "Economic", "Power" and "Standard" according to their actual vehicle conditions.
The switching of three driving modes can meet more adaptation scenarios and provide more energy-saving operation methods;
* Multi-level energy feedback: effectively reduce the energy consumption of the vehicle and reduce the loss of friction plates,
Further reduce operating costs for customers. The energy feedback grading is optional, which can be used in different loads,
Feed back more energy under different working conditions and extend the cruising range;
* High-power charging: standard battery cooling, continuous high-power charging, only need to be fully charged
1.5 hours, high charging efficiency;
7
* Lightweight design: aluminum alloy cargo boxes, aluminum alloy brackets and other lightweight designs minimize the curb
weight of the vehicle, and at the same time are equipped with large-capacity cargo boxes to improve the carrying efficiency
of the vehicle and give customers more returns;
Vehicle intelligence
* Smart housekeeper: provides various services such as vehicle monitoring, maintenance reminders, and operation data analysis.
Service, the user's caring butler.
* Hill assist + cruise control: Steep slopes can start easily and smoothly, cruise control liberates your feet,
Reduce energy consumption and effectively reduce driving fatigue.
8
Table of contents
Preface ................................................................................................................ 1
Overview of BYD T45C01 Pure Electric Truck .................................. 3
Table of contents. .........................................................................................9
Chapter 1 Safety Precautions ...................................................................................... 16
1-1. Safety Regulations ........................................................................................................... 16
1-2. Layout of high-voltage lines. ................................................................................................ 16
1-3. Restraining device ............................................................................................................18
Seat Belt Use and Adjustment .................................................................................. 18
1-4. Precautions for vehicle fire protection. ........................................................................................ 19
Electrical system fire causes and precautions ................................................................................. 19
CHAPTER 2 BEFORE DRIVING .............................................................................21
2-1. Key information............................................................................................................21
smart key. ............................................................................................................21
2-2. Main power switch. .................................................................................................. 22
Main power switch position ............................................................................................... 22
9
Closing and disconnecting the main power switch...........................................................................................23
2-3. Opening, closing and locking the doors.......................................................................................24
Door locks. .................................................................................................................................................. 24
2-4. Inspection before driving .......................................................................................................25
Check before power-on. ........................................................................................................................................25
Wiper and washer fluid fill ................................................................................................................ 26
Power battery power. ................................................................................................................................... 27
Wipers and washer. ................................................................................................................................27
Lighting .................................................................................................................................... 27
Tire pressure and wheel bolts and nuts ....................................................................................... 27
Coolant volume ..........................................................................................................................................27
Tightness and Leaks ..................................................................................................................... 28
Equipped. ................................................................................................................... 28
2-5. Adjustable parts ....................................................................................................... 28
Driver's Seat ......................................................................................................................................... 28
Steering Wheel .......................................................................................................................................... 31
rearview mirror......................................................................................................................... 32
Sun visors and shades........................................................................................................ 34
2-6. Storage device. ................................................................................................................ 35
Storage box assembly.....................................................................................................................35
Glove box assembly .....................................................................................................................35
Drawer assembly. ...........................................................................................................................................35
10
2-7. Other devices ................................................................................................... 36
Cigarette Lighter. .............................................................................................................................. 36
backup power. ................................................................................................................. 37
USB charging connector (for radio configuration).................................................................... 37
Warning triangle ....................................................................................................................................... 38
vehicle tools. .................................................................................................................. 39
Chapter 3 While Driving ................................................................... 40
Driving Operations ....................................................................................................................40
Mechanical Parking ..................................................................................................................... 42
Turn Signal Lamps ................................................................................................................ 42
Power off when parked............................................................................................................................ 43
3-1. Dashboard....................................................................................................... 44
Introducing the Dashboard .................................................................................................................44
Instrument Operating Instructions ............................................................................................................. 45
Indicators and Warning Lights ............................................................................................................ 45
3-2. Switch.............................................................................................................................. 53
Meter switch. ........................................................................................................................................ 53
3-3. Operate the lights and wipers ............................................................................. 56
Combination Switch...................................................................................................................56
3-4. Multi-function keys ........................................................................................... 59
Key Function. ............................................................................................................... 59
11
3-5. Air conditioner outlet. ........................................................................................... 62
Instructions for use. ............................................................................................................... 62
3-6. Glass lifter. .................................................................................................62
3-7. Using the Air Conditioning System ............................................................................. 63
Electric Air Conditioning (with Radio Configuration) ....................................................................................63
Automatic Air Conditioning (Optional) ................................................................................... 65
3-8. Using the multimedia system (optional). ............................................................................ 69
Panel operation. ..................................................................................................................................... 69
radio. .................................................................................................................... 70
Bluetooth Phone/Bluetooth Music ................................................................................................... 73
USB Mode. ...................................................................................................................... 73
Navigation (Optional) ..................................................................................................................74
Reversing camera (optional)....................................................................................................74
Intelligent voice function (optional). ................................................................................................. 74
3-9. Other devices ................................................................................................... 75
USB charging connector. ........................................................................................................ 75
Door handle. ........................................................................................................................................... 75
3-10. Driving in special environment ..............................................................................76
Driving on hills and hills .................................................................................................... 76
Driving in rainstorms ...........................................................................................................................................................76
Driving in fog. ............................................................................................................................................... 78
Driving on icy, snowy and slippery roads ......................................................................................................... 78
12
Winter Driving Essentials ................................................................................................................ 78
3-11. Driving assistance system ............................................................................. 83
ABS (Anti-lock Braking System)............................................................................................... 83
Brake priority function. ..................................................................................................................... 84
Regenerative braking function. ..................................................................................................................... 84
3-12. Driving Essentials ............................................................................................ 84
New car run-in ......................................................................................................................... 84
Energy efficient driving ....................................................................................................................... 85
CHAPTER 4 AFTER DRIVING.................................................................. 87
4-1. Charging........................................................................................................................ 87
DC ..........................................................................................................................................87
4-2. Overhaul the power-off device. ......................................................................................... 89
Function. ............................................................................................................................. 89
Location. ..............................................................................................................................90
4-3. Trailer device................................................................................................... 92
Front tow hook.............................................................................................................................. 92
4-4. Backup Power ........................................................................................................ 92
Backup Power (Optional) ........................................................................................................92
4-5. Disconnect the high voltage circuit. ................................................................................................ 93
Chapter 5 In the event of a malfunction ........................................................... 96
13
If the vehicle does not start ............................................................................................. 96
If the vehicle cannot be driven after starting. ...........................................................................96
If the vehicle has no power output during driving ...................................................................... 96
If the EV function is limited ....................................................................................................... 96
If you want to stop in an emergency ............................................................................................ 97
Power off the vehicle in an emergency ....................................................................................... 97
If the vehicle encounters heavy rain, wading. ............................................................................. 98
If a Trap Occurs ............................................................................................................... 98
If the vehicle needs to be towed. ..................................................................................... 99
If the vehicle is exposed to standing water ....................................................................................... 102
If the tire is flat. ............................................................................................................102
Battery location. .................................................................................................................................... 105
If the vehicle battery is depleted .............................................................................................................. 105
If the key is lost .......................................................................................................107
If the smart key battery is exhausted. ....................................................................... 107
Service Location .......................................................................................................................................... 107
CHAPTER 6 VEHICLE SPECIFICATIONS ................................................................. 111
6-1. Vehicle parameters. ....................................................................................................... 111
Basic parameters of the whole vehicle. ............................................................................................................ 111
Chassis Parameters .................................................................................................................... 113
6-2. Vehicle Identification ............................................................................................. 116
14
Vehicle Identification Number Location ....................................................................................................... 116
Vehicle nameplate location. .............................................................................................................................................. 116
Motor identification location............................................................................................................. 117
6-3. Main components of new energy............................................................................... 117
Power Battery. ................................................................................................................. 117
Vehicle Controller ........................................................................................................................................121
Integrated Controller .............................................................................................................. 121
motor. ................................................................................................................. 122
Abbreviations. ................................................................................................... 123
15
Chapter 1 Safety Instructions
1-1. Safety Regulations
In order to ensure driving safety, vehicle operation should pay attention to the following matters:
* Regularly maintain the vehicle in strict accordance with the maintenance plan. * When
driving, overloading, speeding, and fatigue driving are strictly prohibited. * The maintenance of high-voltage devices
must be performed by qualified electricians with high-voltage electrician certificates and strictly abide by the electrician safety operation rules.
* Non-professionals are prohibited from touching and disassembling high-voltage
components. * When the vehicle is charging, other related operations or operations on the vehicle are prohibited.
1-2. High voltage line layout
During accident rescue, attention should be paid to avoid high-voltage lines and high-voltage devices to avoid danger.
1 Air heat PTC 2 Air conditioning compressor 3 Power battery 4 Water heat PTC
5 Power distribution box 6 All-in-one 7 Battery 8 Coaxial bridge motor 9 Charging port
16
17
1-3. Restraint device
Seat belt use and adjustment
Fasten your seat belt before driving. Correct use of seat belts can greatly reduce occupant injuries during
emergency braking, sudden turns and collisions.
Adjust the seat as needed and sit up straight and well in the seat. Pull the seat belt out of the retractor, insert the
head of the seat belt into the buckle, and fasten the seat belt.
1* Buckle
2* Take the lead
3* PRESS button
The strap head clicks when it locks in the buckle.
To unbuckle the seat belt, press the red "PRESS" button on the buckle to pull out the seat belt head.
Emergency lock function
The seat belt will be automatically locked when the vehicle brakes suddenly, suddenly turns or collides, so as to effectively restrain
and protect the occupants.
When the vehicle is running smoothly, the seat belt is pulled out and retracted as the occupant moves slowly and smoothly, and the
occupant can move freely. If the rewinding of the seat belt is blocked, the seat belt can be tightened and then released, and the seat
belt can be rewound smoothly.
warn
18
*Be sure to fasten your seat belt before driving.
*A seat belt is only allowed to be worn by one person at a time (not even children).
*The lock socket must not be blocked, otherwise the lock tongue will not be able to lock. *The
seat belt must be placed in front of the hips, not around the abdomen, and must always be
Close to the hips.
*When the seat position cannot guarantee the correct deployment of the seat belt, no seating is allowed. *
The seat belt is not allowed to be altered, damaged or subjected to strong force in an accident
The seat belt of the load must be replaced.
*Pregnant women must pay attention: it should be close to the hip and as low as possible to avoid pressure on the
abdomen. *Children under the age of 13 or under 1.5M in height cannot use ordinary seat belts.
1-4. Precautions for vehicle fire protection
The main causes of vehicle fire are electrical failure, mechanical failure, operating factors and local high temperature, which are mainly
divided into the following aspects.
Electrical system fire causes and precautions
Fires caused by electrical appliances and circuits are mainly due to damaged electrical circuits, short circuits caused by aging, electrical
equipment failures, poor contact at the plug-in position, overloaded equipment circuits, and improper operation.
Notice
*Regularly check whether the fixed points of electrical circuits are loose, poor in contact, or worn. * Regularly
check whether the wiring harness is too close to the moving parts or is worn, and whether the protective sheath of the wiring harness
is damaged or lost. If necessary, immediately check whether the insulating part is damaged, and strengthen protection measures.
Shi.
*Regularly check whether the circuit is too close to the heat source.
Replace the wiring harness immediately.
*Regularly check electrical components, especially the contact points for dust and contaminants.
19
* Regularly check whether the fire extinguishing device is working properly.
*Operate all electrical components according to specifications.
* Pay attention to whether the vehicle has abnormal noise or smell while driving. If so, please stop and check immediately.
clear cause.
* When charging, check whether the protective cover of the charging port is in good condition and not damaged, and whether there are
foreign objects or accumulated water inside the socket. electric shock).
* Pay attention to whether the appearance of each visible surface of the power battery has any color or state changes such as yellowing,
blackening, bulging, burning marks, etc. If there is, please contact BYD sales and service personnel to deal with it in time.
warn
* It is strictly forbidden for flammable substances to approach all kinds of electrical equipment and
connectors. * It is strictly forbidden to use water to wash high-voltage electrical equipment, high-pressure chamber, electrical
components, etc. * It is strictly forbidden to modify or install circuits and electrical equipment without permission to avoid circuit overload and modification.
The insulating layer outside the wiring harness is damaged during installation, resulting in a short circuit.
* When replacing electrical appliances and circuits, it is necessary to use BYD genuine parts to avoid fake and inferior products
cause a fire.
20
Chapter 2 Before Driving
2-1. Key information
smart key
1. Click the lock button 2. Click the unlock button 3. Remote control car search button
Electronic smart key function diagram
Notice
* Persons with implanted pacemakers or defibrillators should keep away from intelligent access and activation systems.
conventional detection antennas, as electromagnetic waves can affect the normal use of such devices.
* In addition to users of implanted pacemakers or cardiac defibrillators, users of other electronic medical devices should also
consult the manufacturer about the use of the device under the influence of electromagnetic waves.
Related Information. Electromagnetic waves may have unpredictable consequences for the use of such medical devices.
fruit.
21
action Function
tap the lock key The doors on both sides of the cab are locked, and the door cannot be opened by pulling the door handle.
Tap the unlock key The doors on both sides of the cab are unlocked, and the door can be opened by pulling the door handle.
Long press the remote control to find t he car The horn sounds and the emergency warning light of the whole vehicle flashes, and it stops automatically after 28s.
Button 1.5s After triggering the car search alarm, press the car search button for 1.5s to cancel the alarm.
Note:
1 The electronic smart key has an indicator light (red), each time a signal is sent, it lights up once, and the lighting time is
250ms. When the indicator light is normally on, it indicates that the electronic smart key is working normally; when the indicator light is dark, it indicates that the electronic smart key is working normally
The battery power is too low or the signal is too weak.
2 It has a transponder for transponders, which can be used as a backup when there is no battery, low battery power, or communication interference.
2-2. Main power switch
Main power switch position
The position of the main power switch is as shown in the figure
Main power switch position
22
Closing and opening the main power switch
1. Closed (ON) state.
2. Disconnected (OFF) state.
23
2-3. Opening, closing and locking the doors
door lock
12
1. Lock cylinder 2. External handle handle 3. Mechanical key 4. Remote control key
*Open the door:
After pressing the unlock button on the remote control key to release the door lock state, pull up the outside handle handle (as shown in
Figure 2) to complete the door opening action.
Note: In the case of failure of the remote control key, you need to remove the mechanical key to unlock (as shown in Figure 3),
Then insert the key into the hole of the lock cylinder (shown in Figure 1), turn the key clockwise, and pull up the handle of the outer handle to complete the
door opening.
*To lock the door:
24
After the occupant comes out of the cab and closes the door, press the lock button on the remote control key to
Lock the doors.
Note: In the event of failure of the remote control key, after the occupant comes out of the cab and closes the door, the
Rotate the key in the opposite direction when opening the door to complete the door lock action.
Notice
*After opening the door, do not use external force to keep the lock tongue in a locked state. When the door is closed in this state, the lock
tongue and the lock ring will collide.
2-4. Inspection before driving
Check before power on
Before powering on for the first time on the day, a safety inspection of the vehicle is helpful for driving safety.
*Tires: Check tire pressure with a tire pressure gauge and carefully inspect for cuts, damage, or excessive
degree of wear.
*Wheel Nuts: Verify that no nuts are loose or missing. * Battery: Check whether the
battery connector is corroded or loose, whether there is any crack in the appearance, whether
Leakage.
* Maintenance power-off device: integrated on the right all-in-one controller, confirm that the maintenance power-off device is in the closed state
as shown in the figure below. When the vehicle needs to be repaired, press and hold the lock to pull down. (image has been updated)
25
* Coolant level: Make sure the coolant level in the expansion tank is at the maximum and minimum scale lines
between.
* High and low voltage wiring harness: Check for damage and
looseness. * Make sure the cab is in the normal locking state.
Brake pedal: Make sure the pedal has enough free play.
Wiper and washer fluid filling
If the washer is not working, the washer fluid jug may be empty. Check the washer fluid level on the level gauge.
Clean water can be used as a washing liquid. However, in cold areas, when the temperature is below zero, a
washing liquid containing antifreeze must be used. Such products are available at BYD authorized service stores and
most auto parts stores. The mixing ratio with water can be according to the manufacturer's instructions. After the washing
jug is filled with washing liquid, screw the lid tightly.
Notice
* Do not use other antifreeze as the washer fluid for the front windshield at low temperature, which will damage the
paint layer of the vehicle.
In freezing weather, use a defroster to warm the windshield before using the cleaner.
26
This prevents washer fluid from freezing on the windshield and compromising visibility.
Notice
* Do not use the wipers when the windshield is dry. Otherwise it will scratch the glass
glass.
Power battery power
Turn on the power, check the indicator light on the indicator for power display, if the power is too low, it needs to be charged before driving.
Wipers and washer
Turn the power on and operate to check whether the wipers and washer are in normal working condition.
Check that the washer fluid level is between the maximum and minimum levels.
lighting
Turn on the power to check whether the lamps work normally.
Tire pressure and wheel bolts and nuts
Check the tire pressure, refer to the tire pressure value in 6-1 Main technical parameters of the vehicle, and carefully check for
cuts, damage or excessive wear.
Check whether the bolts and nuts of the wheel are complete, well tightened, and whether the paint mark is shifted.
coolant volume
27
The coolant level should be kept between the MAX
and MIN scales.
warn
* When the water temperature is high, please do not open the cover of the water tank to avoid burns.
tightness and leakage
Visually inspect axles, steering systems, cooling systems, etc. for leaks.
Equipped
Check whether the vehicle equipment, such as on-board tools, are complete and in good condition, and whether the fire extinguisher is
in normal use.
2-5. Adjustable parts
driver's seat
The driver's seat can be properly adjusted using the adjustment handle provided with the seat. Adjust the
driver's seat so that the foot pedals, steering wheel and dashboard controls are all within easy reach of the driver.
28
warn
* For the sake of safety, the seat adjustment must be carried out when the vehicle is stopped, and it is strictly prohibited to
adjust the seat while the vehicle is running.
Notice
* Please read the instruction manual carefully before using the driver's seat, so as to understand the operation of its various
functions. * Please accompany the user manual with the vehicle to ensure that the driver can read it immediately. * The
driver's seat should only be assembled and repaired by professionals. * The seat consists of safety components. Any quality
problems caused by the modification of the seat and operation not in accordance with the instruction manual are not covered
by the warranty.
* The seat fixing and each adjustment locking mechanism should be checked regularly.
29
Function of each adjustment button
1. Seat back angle adjustment handle 2. Seat front and rear adjustment handle
3. Shock absorber adjustment handle (high configuration) 4. Seat armrest (overseas high configuration)
5. Seat heating button (overseas high configuration)
* Hold the handle 1 and rotate it to the rear of the vehicle, then adjust the seat back to the required
angle, release the lever 1, use the back to lower the backrest, and the handle 1 springs back to its original position;
30
* Pull up the front and rear adjustment handle 2, the driver can adjust the front and rear according to their own comfort
Adjust the seat, release lever 2, rock the seat back and forth to lock;
* According to the body weight or the road conditions of the vehicle, turn the shock absorber adjustment handle 3 by hand,
The firmness of the seat can be adjusted to a suitable state;
* According to the actual needs of the driver, if seat heating is required, press button 5 in the instrument panel,
The seat heating can be turned on.
steering wheel
Pull the adjusting wrench 1 backward to open the adjusting locking mechanism, then hold the steering wheel with both hands, and adjust the steering wheel
up and down, back and forth according to the driver's needs, and then turn the adjusting wrench to the locked position after adjustment.
1. Steering wheel adjustment lock wrench
31
Danger
The adjustment of the steering wheel must be carried out when the vehicle is stopped, and it is strictly prohibited to adjust the steering wheel while the
vehicle is running.
rearview mirror
Instructions for use
* In order to ensure that both sides of the vehicle body can be clearly seen during driving and ensure driving safety,
The mirrors have manual adjustment.
* The driver can adjust the lens before driving to meet the driving vision requirements.
Rearview mirror electric adjustment instructions for use
32
Rearview mirror electric adjustment switch
* Button 1——Adjust the main exterior mirror lens upward; * Button 2——
Adjust the main exterior mirror lens to the left;
* Button 3 - adjust the lens of the main exterior rearview mirror to the right;
* Button 4 - downward adjustment of the main exterior rearview mirror lens;
* Button 5——Select to adjust the left exterior mirror;
* Button 6 - Select to adjust the right exterior mirror.
33
Rearview mirror electric heating adjustment instructions
Electric heating switch
1. Press the electric heating switch 1 to turn on the electric heating of the main exterior rearview mirror;
2. Press the electric heating switch again. 1. Turn off the electric heating of the main exterior rearview mirror.
Sun visors and shades
sun visor
*To block sunlight from the front, the sun visor can be lowered
34
2-6. Storage device
storage box assembly
The storage box assembly is located on the upper part of the passenger instrument panel assembly, and the storage box cover is upward after pressing the button
Pop open and press down on the storage box cover to close the storage box (opening angle 70°).
glove box assembly
The glove box assembly is located at the lower part of the passenger's instrument panel assembly. Unfasten the glove box button and pull it outwards.
The glove box can be opened. (Opening angle 21°).
drawer assembly
35
The drawer assembly is located in the middle and lower part of the instrument panel assembly. Hold the handle and pull out to open the drawer.
Push the handle back to close the drawer. (Open stroke 100mm).
2-7. Other devices
cigarette lighter
* The cigarette lighter can only work when the ignition switch is in the ON position. * Press the cigarette lighter
until it is locked to heat it. After the heating is completed, the cigarette lighter will
pops up automatically.
* Please put the cigarette lighter back to its original position after use.
36
warn
* Do not use the cigarette lighter while driving to avoid distracting the driver's attention. * The cigarette lighter
socket only supplies power to the cigarette lighter, it is not recommended to use the cigarette lighter socket for other accessories.
power supply.
* Do not use other sockets as the power source of the cigarette lighter.
backup power
* Open the protective cover of the backup power supply, clip it into the vehicle power supply head, and work in the non-
OFF gear; * Convert the 24V voltage to 5V voltage output through the vehicle power supply, the rated power is 360W,
It is not allowed to hang high-power electrical appliances on this circuit to prevent the circuit fuse from being blown;
* After use, take out the vehicle power supply and snap the protective cover of the backup power supply back to its original position.
USB charging connector (for radio configuration)
37
* In non-OFF mode, the charging connector works normally and the single-port output is 5V/2A; * When the
small light is on and off, the backlight of the USB charging connector will light up.
Light;
* Single-port rated output power * 10W (do not use high-power electrical devices)
There are debris deposits on the base of the standby power supply that need to be cleaned to prevent the deposition of debris from causing poor line contact
resistance to increase, resulting in ablation.
warning triangle
warning triangle
Warning triangles are used when the vehicle breaks down on the
road or in other emergencies. Refer to the instructions on the box for usage.
The warning triangle is placed in the on-board tool bag
Picture of warning triangle
warn
* The use of warning triangles must comply with relevant laws and regulations.
38
* When placing warning triangles, please pay attention to personal traffic safety, distance and location
appropriate to the prevailing road and traffic conditions
vehicle tools
vehicle tools
Jack assembly 5T
Picture of on-board tools
jack rocker (for use with 5T jack) Socket wrench
30*32 Metric double open-end
wrench 8*10 Metric double open-end
wrench 12*14 Tool bag Phillips
screwdriver Slotted
screwdriver
Location: Behind the passenger seat
39
Chapter 3 While Driving
driving operation
start up
1. Turn on the main power switch.
2. Fully depress the brake pedal. 3. Press
the start button for 1s to
superior , waiting for the
The "OK" indicator light is on,
indicating that the vehicle is successfully
started.
drive
1. Depress and hold the brake pedal while
Rotate the shift knob to D gear to confirm
The meter shows D gear.
2. Release the parking brake.
3. Gradually release the brake pedal, then,
Press the accelerator pedal lightly to accelerate the
vehicle.
When reversing, depress and hold the brake pedal, and turn the shift knob to R gear at the same time, and confirm that the meter
shows R gear. Other steps are the same as step 2 and step 3.
Slow down and stop
40
1. Release the accelerator pedal.
2. Depress the brake pedal.
3. When parking for a long time, it is necessary to switch to N gear and confirm that the meter displays N gear.
4. If necessary, apply the parking brake.
Parking
1. Depress the brake pedal.
2. After the vehicle is stopped, switch to N gear and switch to neutral gear.
3. Apply the parking brake, the parking brake indicator light on the instrument light up.
vehicle power outage
1. After the vehicle is parked, perform the following operations to power off the vehicle.
2. Press the start button, the vehicle is powered off and the meter goes out.
3. Close and lock the doors and keep the key with you.
4. Disconnect the main power switch.
Notice
* If you will not drive on that day, it is recommended to turn off the main power switch.
41
Mechanical parking
Apply mechanical parking
Pull up the parking handle manually
Pull the parking handle back, as shown in the figure, the indicator light
on the instrument is always on, which means thp

aat rth
kiengmheacshabneie
canl
implemented.
Release mechanical parking
Manually release the parking handle
Lift the handle lightly, the parking handle springs back
to the front, the indicator light of the instrument goes
out, and the mechanical parking is released.
turn signal lights
42
*Right turn signal control: Move the joystick to the front of the
car, the right turn signal and the indicator on the
instrument panel keep flashing.
*Left turn signal control: Move the joystick to the rear of the car,
the left turn signal and the indicator on the instrument
panel keep flashing.
* W hen the steering wheel ret urns to the normal position, t he joystick
automatically retur ns to its original position.
Power off when parking
* Parking: Depress the brake pedal to stop the car smoothly;
*Switch the gear to N gear;
* Pull up the parking handle or the EPB switch (optional), press the start button, the vehicle will
Electricity;
*If the vehicle will not be used for a long time, disconnect the main power switch.
Notice
*Vehicles without bodywork should be parked in a canopy or indoors. If it is limited by conditions and it is placed in the open air for a short
period of time, it is necessary to cover the loading area of the bodywork to prevent exposure to sunlight, water ingress or accumulation of
foreign objects.
43
3-1. Dashboard
Dashboard introduction
Dashboard interface
1 Time display 3 2 high beams
Turn signal 5 Gear 4 OK light
position display 7 6 low beam
Small light 9 Total 8 Speedometer
mileage 11 Battery 10 Driving information
capacity meter 12 Power meter
44
Instrument Description
Instrument driving information
Driving information name Function Description
average speed Accumulated total mileage/accumulated driving time, can be reset
Total travel time / travel time, travel time can be reset,

total travel time
Total travel time cannot be reset
energy flow diagram Show energy flow mode
Cumulative charging power Displays the cumulative total charge
battery voltage Display t he current voltage value of the battery
Cumulative average energy consumption Display the average energy consumption of accumulated 100km
Average energy consumption for the last 50km Average energy consumption for the last 50km
Instrument Operation Instructions
Meter menu switch
: Select up; switch driving infor mation up.
: Select dow n; switch the driving information dow n. Menu: Display
the main menu of the instr ument; confirm.
Meter mileage and backlight adjustment switch
+: The backlight brightness is increased by one notch.
-: The backlight brightness is decreased by one level.
Mileage: short press to switch mileage display; long press to clear short mileage.
Indicators and Warning Lights
45
Indicator/Warning Light
Kind tips
* Due to the specific configuration of the vehicle model, some indicator lights of this vehicle may not be used.
You pay attention.
* During vehicle startup, it is normal for the indicator light to light up for about 3 seconds during self-check.
Red indicator light:
icon name
Seat belt not fastened indicator
Power battery connection indicator
Parking Brake Indicator
DC fault indicator
Power battery low warning indicator
Powertrain malfunction indicator light
Power battery fault warning light
Motor and controller overheat warning light
Drive motor fault indicator
46
fire warning indicator
water temperature warning signal
brake system warning light
Steering power failure indicator light
Load dump indicator
Inter-wheel differential indicator
Inter-axle differential indicator
AEBS emergency stop indicator
Trailer independent braking function on prompt
PTO indicator
EPB fault warning light
Parking force detection enable prompt
seat belt indicator
47
SRS fault indicator
Yellow light:,
Smart key system warning light
ADAS indicator
ACC fault warning light
Lane Keeping Indicator
speed limit indicator
rear fog indicator
Trailer ABS indicator light
Friction disc alarm indicator
ESC fault indicator
ESC OFF indicator
ABS malfunction warning light
ASR status indicator
48
Hill start assistant indicator
tire pressure indicator
AEBS AEBS Emergency Brake Indicator
EPB fault warning light
Power-limited driving indicator
R gear indicator
Green light:
icon name
left turn indicator
right turn indicator
Low beam indicator
Front fog light indicator
small light indicator
Main light switch indicator
49
Energy feedback gear
Air pressure indicator
AEBS emergency stop indicator
OK indicator
Bodywork OK light
P gear indicator
N gear indicator
D gear indicator
D2 gear indicator
D3 gear indicator
D4 gear indicator
D5 gear indicator
D6 gear indicator
50
ECO Mode Indicator
SPORT mode indicator
BASIC Mode Indicator
Cruise control main display indicator
cruise control indicator light
ACC Status Indicator
Blue light:
icon name
High beam indicator
Indicator/Warning Light Description
In the following cases, please contact BYD sales and service personnel to check the vehicle:
brake system warning light
When the power gear is in the "OK" gear, the brake fluid level is lower than the normal state or the vacuum booster system
When the system fails, this light is on. A brief illumination of the warning light during operation does not indicate a problem.
Steering power failure indicator light
When the power gear is in the "OK" gear and the steering motor fails, the light will be on.
51
When this light is on, it is necessary to check whether the steering motor and controller are damaged.
Power battery fault warning light
This light is used to warn of power battery failure status.
If this light is on, it means the power battery pack is faulty.
Contact BYD sales and service personnel as soon as possible.
ABS malfunction warning light
When the power gear enters the "OK" gear, this light is on. If the anti-lock brake system is working properly
Normally, the light turns off after a few seconds. After that, if the system fails, the light will come on again.
DC fault indicator
When this light is on, check whether the DC is damaged, whether the battery is normal, and whether it cannot be charged.
Motor and controller overheat warning light
If the indicator light is on, it means that the motor temperature is too high, it is necessary to stop and cool down the motor.
fire warning indicator
If the indicator light is on, it means that the temperature of the power battery is too high, and it must be stopped to cool down.
52
3-2. Switch
Meter switch
1
2 3 4 5 6 7
1* Mode switch3 Shift knob 2* Feedback adjustment switch
5* 4* Front windshield defrosting and defogging switch

EPB Park Button (Optional)
7* Volume knob assembly (optional) 6* Hazard warning light switch
Meter switch icon name Function
53
+: The backlight brightness is increased by one notch.
-: The backlight brightness is decreased by one level.

Meter switch
: Short press to switch mileage display; long
press to clear short mileage.
After lighting the low beam, scroll the wheel on the switch
to adjust the height of the low beam. Adjust from 0 to 3, the
dipped beam illumination height gradually decreases,
headlight adjustment switch
Adjust from 3rd to 0th gear, and the dipped beam illumination
height gradually increases.
Short press the switch to turn on and off the PAD; long press
Volume knob assembly

the switch to restart the PAD; rotate the switch to the left to
(with PAD
decrease the multimedia volume; rotate the switch to the right
Time)
to increase the multimedia volume.
54
Press the switch, and the vehicle power modes will be
Mode switch switched between the economy (E), standard (B) and
power (P) in turn.
Press the switch, the energy feedback intensity of the

Feedback adjustment switch
whole vehicle switches between 3 levels in turn
Press the switch to turn on the defrost function of the

Front windshield defrost
front windshield; press it again to reset the switch and
and defogger switch
turn off the defrost function of the front windshield
Press the switch, the turn signal flashes and the turn
Hazard warning light symbol of the combination meter flashes, press it
switch again, the switch resets and stops flashing.
Rotate the shift knob to the right, the D gear indicator light is on
forward gear On, the gear position on the instrument shows D, at this time it is the front
into the file.
Rotate the shift knob to the middle, the N position indicator
neutral Lights up, the gear position on the instrument displays N, at this time it is
gap.
Turn the shift knob to the left, the R gear indicator light is on
reverse gear On, the gear on the instrument shows R, at this time it is reverse
files.
55
Heated exterior mirrors
Switch to turn on or off the heating function of the exterior rearview mirror
3-3. Operate the lights and wipers
Combination Switch
Overtaking lights, high beams
* After moving the joystick up, the overtaking light
light on, release off
* After the dipped beam is on, move the joystick down
After the toggle, the high beam lights up, manually pull
Turn off after returning.
Small lights, low beams, fog lights
56
* OFF closure
* small light stall
* headlight stall
* Rear fog lamps
1- Lighting knob 2- Fog light knob
turn signal
* turn signal
* Turn the handle clockwise to open
Turn on the right turn signal
* Turn the handle counterclockwise to open
Turn on the left turn signal
* Manually reset the light handle or steering
Turn the disc, turn off the turn signal
Windshield Wipers and Washers
57
Operation method:
Turn the lever clockwise or counterclockwise
to control the windshield wipers.
There are five gears:
* MIST: Jog
*OFF: Stop *INT:
Intermittent * LO: Low-
speed wipe * HI: High-
speed wipe
* : The wiper sprays water and wipes the water;
Release to stop
spraying. * Move the wiper handle upwards,
The windshield wipers start spraying water, and the same
When wiping, let go, stop
water spray.
58
3-4. Multi-function keys
Key Function
* * Turn
* on or off cruise control.
* [ ] Cruise suspended (after pressing the switch, the cruise function is in a pending state)
* Press [RES+], the target speed will increase by 0.5km/h~1km/h; long press, the vehicle speed will continue
to rise, and the vehicle speed when the button is released is set as the target speed. * Press [SET*],
the target speed will decrease by 0.5km/h~1km/h; long press, the speed will continue
When descending, the vehicle speed when the button is released is set as the target speed.
**A
* dd 1 gear to the following distance, a total of 6 gears (cycle gears).
* [OK] Under the menu interface: short press this button to select the corresponding sub-menu in the menu;
under the driving information interface: you can clear some driving information by long pressing this
button for more than 2 seconds; the driving information interface Down: you can switch to the safe
driving prompt interface or menu interface by short pressing this button; below the fault/prompt
information interface: you can switch to the driving information display page by short pressing this button to reserve cha
During electrical settings, press to toggle between hour and minute settings.
59
* *U
* nder the menu interface: you can short press this button to change the options in the menu.
Switch up selection or increase selection; under the driving information interface: you can switch up each
driving information by this button; under the fault/prompt information interface: you can switch to the
driving information display interface by this button; when reserving the charging setting, press the switch
Increase hours/minutes.
* *U
* nder the menu interface: you can short press this button to change the options in the menu.
Switch down to select or reduce selection; under the driving information interface: you can use this button
to switch down each driving information; under the fault/prompt information interface: you can use this
button to switch to the driving information display interface; when reserving charging settings, press
Toggle down to decrease hours/minutes.
*M
* odeS
* elect mode: PAD jumps to the radio interface, you can press FMA
* M*
Switch cycle between USB (if the USB interface has been connected to a U disk) *AUX (if the player
has been connected to the AUX interface) *SD (if already inserted) *FM. If the speaker is in the off
state, short press MODE to start the operation and enter the memory playback mode when it was turned
off last time. Press again to switch in the above order; long press to turn off the sound system.
* * I*n radio mode: long press: automatically search for the last strong signal station (turn down
frequency); short press: select the pre-stored station up (turn down the frequency), and can switch
between FM3-FM2-FM1-FM3 (AM2-AM1-AM2). In USB/SD mode: Short press: play the previous song
(track number-1); play time > 3s, return to the beginning of the track,
Playing time <= 3S, switch to the previous song (track number-1);
* * I*n radio mode: long press: automatically search for the next strong signal station (up
frequency); short press: down to select the pre-stored station (to increase the frequency), and can
60
Switch between FM2-FM3-FM1 (AM1-AM2-AM1). In USB mode: short press: play the next song (track
number + 1); long press: fast switch between tracks (track number +);
* [+] Short press: increase the volume in one step. *
[-] Short press: decrease the volume in one step.
* *P
* ress the lever multimedia to enter silent mode
* *D
* ial/answer (The audio system will enter the mute state after pressing this button.)
* *E
* nd the call (the audio system was muted before, then the audio
The system restarts the work it did before it was muted).
* *P
* ress the voice recognition switch, the multimedia screen switches to the voice recognition page,
Intelligent voice function can be realized. Press again to re-enter the voice command.
61
3-5. Air conditioner outlet
*Move the fork up and down to adjust the wind direction up and down; *Move the
fork left and right to adjust the wind direction from left to right;
Note: There are 4 air outlets in total, and the operation is the same as above.
3-6. Glass lifter
driver side passenger side
62
*[ ] Window lift function (the left button on the driver's side controls the main driver's side glass
up and down, click to operate, the main driver's side window can be lowered automatically;
key to control the glass lift on the passenger side)
**S
* elect to adjust the driver's side mirror
**S
* elect to adjust the passenger side mirror
* [ ] Rearview mirror upward adjustment
* [ ] Adjust the rearview mirror to the right
* [ ] Rearview mirror downward adjustment
* [ ] Adjust the rearview mirror to the left
3-7. Using the air conditioning system
Electric air conditioner (with radio configuration)
63
1. Air volume adjustment knob 2. Mode switching 3. Multiplex button 3 4. Multiplex button 1 5. Multiplex button 4 6. Multiplex
button 2 7. Multiplex button 6 8. Automatic air conditioning switch 9. Air conditioning refrigeration 10. Air-conditioning mode 11.
Air-conditioning internal and external circulation switching 12. Air-conditioning temperature down 13. Air-conditioning temperature
up 14. Volume knob/switch power
Control panel operation
(1) After the car is powered on in the OK gear, if the air conditioner is on, press [8] to turn off the air conditioner.
And automatically return to the audio mode; if the air conditioner is off, press [8] to turn on the air conditioner, enter the air
conditioner mode, and adjust the button [9] to turn on the air conditioner.
2. Time display
64
The control panel display* the time.
3. Wind speed display
(1) Control panel display [ ] Displays the set wind speed, and when the wind speed is adjusted, the
The display changes accordingly.
(2) Rotate the knob [1] to adjust the amount of air volume, the amount of cyclone to the left decreases, and the amount of cyclone to the right
increases
4. Temperature display
(1) Control panel display [ ] to display the cold or hot of the set temperature, adjust
The display also changes correspondingly when the temperature is changed;
(2) Press the button [12], the temperature will decrease by one degree.
(3) Press the button [13], the temperature will increase by one degree.
5. Mode selection
(1) Press the [10] key to select the operation mode of the air conditioner;
(2) There are 5 operating modes of the air conditioner, namely "face blowing + foot blowing", "foot blowing + defrosting", "face blowing", "foot
blowing" and "defrosting".
6. Compressor
Press9*k*ey to turn off and on compressor cooling.
7. Internal and external circulation operation
Press1*1*to switch between inner and outer loops.
Automatic air conditioning (optional)
65
Panel appearance
A* ir conditioning control panel
Control panel operation
* The air conditioner is turned on and off
* After the car is powered on in the ok gear, if the air conditioner is on, press [Off], the air conditioner
closure. If the air conditioner is on, press [On] to turn on the air conditioner. * Temperature
Control panel display [ ] Display the set temperature, and the display will also match when adjusting the temperature.
should change, the panel [ ] to display the current temperature.
* Wind speed adjustment
66
Control panel display [ ] Display setting wind
speed, adjust the wind speed [ ], the display will change accordingly.
* Blow mode adjustment
There are 5 operating modes of the air conditioner, and* i*n the panel displays the current mode.
* * "Blowing noodles", "Blowing feet", "Blowing
"Face + foot blowing", "foot blowing + defrosting", "defrosting", when different commands are pressed, the air supply mode of the
air conditioner can be changed.
* Air conditioning cycle mode
The control panel display [ ], the inner loop is lit, it is the inner loop, the inner loop icon
If it is not lit, it is the outer loop* .*
* Front defrost
Display* o* n the control panel, click the icon to enter the front defrost directly.
* Refrigeration
Click [ ] on the control panel display to enter the cooling mode.
* Auto mode (when equipped)
Click [Auto] on the control panel display to enter the cooling mode.
67
* Ventilation
* [Ventilation] Turn off the ventilation function.
* Bluetooth call automatic speed reduction function
*By default, the fan speed of the air conditioner is automatically reduced during a Bluetooth call, and this function can be turned off in the settings.
Air conditioning refrigerant detection:
Air-conditioning refrigerant pressure detection: turn off the air-conditioning compressor, use a pressure gauge, connect the high-pressure filling
port and the low-pressure filling port at the same time, and read the value after the pressure is stable, between 0.6MP~1MP (the distance value is affected by
the ambient temperature) Normal, the value is too low, the refrigerant is lacking, and the refrigerant needs to be refilled; the value is too high, the refrigerant is
too much, and the refrigerant needs to be refilled.
Leak detection of air-conditioning refrigerant: use a halogen detector if possible, around the pipeline
When moving, an alarm will sound at the place where the refrigerant is missing. If there is no alarm, there will be no refrigerant leakage.
When there is no professional instrument, use soap mixed with water to brush the surface of the pipeline with a brush,
The place where a large number of bubbles appear is the point of leakage of refrigerant, and there is no leakage of refrigerant if there are no bubbles.
Refrigerant filling method:
* If possible, use an automatic refrigerant filling machine, and connect the high and low pressure pipes respectively.
On the high and low pressure filling ports, the remaining refrigerant in the channel pipeline is firstly extracted, and then vacuumed.
If there is no automatic refrigerant filling machine, give priority to vacuuming the air-conditioning
pipeline, and then refill the refrigerant.
refrigerant.
The specific method of vacuuming the air conditioner:
* Use the manifold pressure gauge set, the middle pipeline is connected to the vacuum pump, and the two pipelines are
High and low pressure filling ports should be connected;
* Open the high and low pressure manual valves of the manifold pressure gauge group, start the vacuum pump, and observe the pressure.
Force meter, vacuum the system to 98~99KP;
68
* Close the high and low pressure manual valves of the manifold pressure gauges and observe whether the pressure of the pressure gauges is
If the echo rises, the pipeline leaks. If it does not rise, open the high and low pressure manual valve, start the vacuum
pump and continue to pump for 15~20 minutes, so that the vacuum pressure gauge is stable;
* High and low pressure manual valves on line manifold pressure gauges; *
Line vacuum pump.
The specific method of adding refrigerant to the air conditioner:
Use special equipment for filling, the filling amount is 650g/car, and the gauge pressure on both sides of high and low pressure is
0.6~0.8MPa after filling. After filling, the air conditioner will run normally. side is 0.15 to 0.3 MPa.
3-8. Use multimedia system (optional)
*PAD display
Panel operation
The configuration panel of this car is a capacitive touch panel, and you can tap the display image on the interface with your finger.
69
icon, you can enter different functions, to exit the function, please click the home button on the display
“ ”
radio
1. Air volume adjustment knob 2. Mode switching 3. Multiplex button 3 4. Multiplex button 1 5. Multiplex button 4 6. Multiplex
button 2 7. Multiplex button 6 8. Automatic air conditioning switch 9. Air conditioning refrigeration 10. Air-conditioning mode
11. Air-conditioning internal and external circulation switching 12. Air-conditioning temperature down 13. Air-conditioning
temperature up 14. Volume knob/switch power
Radio operation:
1. Press and hold the left knob to turn on the power and enter the radio mode;
70
2. When the radio is on, short press the multiplex button 3 to automatically search for a strong signal station -, short press again to
stop the search; short press the multiplex button 4 to automatically search for a strong signal station +, again Short press to stop searching.
Radio Mode:
Multiplex
Multiplex Multiplex button Multiplex Multiplex button
button 1
button 2 3 button 4 5
radio* Mode switching: cyclically

radio*
Short press, auto search select in the order of radio-
no response no response Short press, auto search
a strong signal station bluetooth music mode
A strong signal station
+*
Volume adjustment:
Rotate the left knob clockwise or counterclockwise to adjust the volume and price range
The range is 00-39.
Mode switch:
During the normal operation of the receiver, press the multiplex button 5 continuously to switch, that is, the mode R button, to switch
playback between FM mode and Bluetooth.
Sound adjustment:
Short press: sound effect adjustment
Switch between sound effect adjustment modes BAS, TRE, BAL, FAD, ANC;
Long press: no response
71
When adjusting, add or subtract by rotating the left knob
Bluetooth function:
Turn on the Bluetooth of the mobile phone, search for the Bluetooth name: BYD, pair it on the mobile phone endpoint, you can pair it,
Bluetooth music, Bluetooth phone can be used. (Bluetooth phone depends on the specific configuration of the vehicle)
After switching the Bluetooth music, users can adjust the volume according to their own needs, pause,
Sequence play, previous song, next song function.
Bluetooth music mode:
Multiplex
Multiplex
button 1 Multiplex button 3 Multiplex button 4 Multiplex button 5
button 2
Short press, previous Short press: next Mode switching: cyclically
Pause repeat song; long press, fast song; long press, fast select in the order of radio-
playback forward selection backward selection bluetooth music mode
To sum up the radio mode && Bluetooth mode switching:
Multiplex Multiplex
Multiplex Multiplex button Multiplex Multiplex
button 1 button 6
button 2 3 button 4 button 5
model
72
Mode
Short switching: Short press:

Short press,
press: cyclically switch
previous song;
Pause repeat next select in the between
long press, fast
playback song; long order of radio- sound effect
forward selection
Bluetooth mode press, fast bluetooth music adjustment
backward selection mode and sound adjustment modes
DOWN,
THREE,
Multiplex BAL*
Multiplex Multiplex button Multiplex Multiplex
button 1 FAD*
button 2 3 button 4 button 5
ANC*
model
FM1;
long press:
when there is
Mode
no response
radio* switching:
radio: Short adjustment,
Short press cyclically
press to adjust the
Not Not to automatically select in the
automatically addition and
responding responding search for a order of radio-
search for a strong subtraction by
strong signal station bluetooth music
radio mode signal station rotating the left knob
+* mode
Bluetooth Phone/Bluetooth Music
Multimedia Click the Bluetooth icon on the display screen to enter the Bluetooth interface. In the Bluetooth configuration, according
to the device name and matching code displayed by the multimedia, pair and connect with the mobile phone. After connection, you can
make calls and view the address book through multimedia, record the phone records during use, and play Bluetooth music.
USB mode
73
This system supports standard USB interface U disk, if you want to use U disk, please insert U disk into USB
port, press button 2 (MODE) to enter USB mode, which supports playing audio and video files in mp3, MP4 (optional), AVI and other formats.
Navigation (optional)
This system is equipped with a truck navigation system.
Reversing camera (optional)
The system is equipped with a reversing camera, which can display the reversing image.
Intelligent voice function (optional)
Smart Voice Control is activated when the user presses the Voice Control button on the multifunction steering wheel
function, it starts to recognize and execute after speaking the command. For detailed instructions, see the instructions in the APP.
74
3-9. Other devices
USB charging connector
* In non-OFF mode, the charging connector works normally, and the single-port output is 5V/2A; * When the
small light is on and off, the backlight of the USB charging connector lights up, and the light-emitting form: inside the interface
glow;
* The rated output power of a single port is * 10W (do not use high-power electrical devices) * There
are debris deposits on the standby power base that need to be cleaned to prevent the deposited debris from causing circuit contact
Bad resistance increases, leading to ablation.
door handle
75
1. Lock cylinder 2. Door handle
open the door
Insert the mechanical key into the hole of the lock cylinder (indicated by the mark 1 in the figure) and rotate the key. After the key is rotated to
the end, pull the handle of the door handle (indicated by the mark 2 in the figure) to open the door. (or operate with the remote control key)
close the door
After the occupant comes out of the cab, close the door and rotate it in the opposite direction to the door opening to complete the closing action.
3-10. Driving in special environment
Ramp and mountain driving
Notice
* Depress the brake pedal before driving to confirm that the braking system is working properly.
* Keep the speed within a safe and controllable range when driving. * Use the
regenerative braking function reasonably to avoid the high temperature of the brake friction parts and the attenuation of the braking force.
Driving in rainstorm
Rainstorm wading conditions and operations
* When the rainfall or rain is heavy, the wiper should be adjusted to the maximum gear to ensure that the driver can see normally.
wild. If the wipers are adjusted to the maximum gear and the road conditions cannot be seen clearly, pull over and turn on the
Emergency warning light.
* When the water depth of the road exceeds the safe wading depth of the vehicle by 250 mm or the length of the water surface exceeds 500 m, drive
away from the wading road.
76
* In the process of wading, you should slow down and drive slowly, and the vehicle speed should be 1* 5 km/h. If the water ripple is large,
The vehicle speed should be reduced to below 5 km/h.
Kind tips
* When driving in water, pay attention to observe whether the instrument has sound and light signals such as fault
alarm. * Immersion depth for short-term parking of vehicles: no more than 300 mm for first-class stepping vehicles; second-class
The stepping vehicle does not exceed 400 mm.
* After the vehicle is wading in water, it is necessary to remove the stored water and check the chassis, especially the braking system, bottom
Check the power battery and motor.
Emergency treatment of wading failure
If a fault alarm occurs, the driver should drive the vehicle away from the flooded road to a safe place as soon as possible, apply the parking
brake, stop the power supply, evacuate the passengers, disconnect the maintenance power-off device, and contact the BYD sales and service
personnel.
Vehicle inspection and maintenance after wading
Kind tips
* After the vehicle is wading through water, a comprehensive inspection and maintenance of the entire
vehicle should be carried out. * If it rains continuously, the frequency of vehicle inspection should be
increased accordingly. * If in doubt, contact BYD sales and service personnel.
warn
* If the power management module or the drive module and the wiring harness sheath are accidentally flooded with water (such as damage
to the sealed compartment, etc.), immediately power off the vehicle and disconnect the main power switch, and wait for the water
to dry before using the vehicle.
* Prevent human hands from directly touching conductive parts, high-voltage wiring harnesses or terminals.
77
driving in fog
1. Turn on fog lights (optional), low beams, position lights and position lights (if the visibility is less than 200m, it is recommended to
turn on the hazard warning flashers).
2. Intermittently turn on the wiper or defogging function to wipe off the water mist from the windshield and improve the driving vision.
Notice
* Keep a sufficient distance from the vehicle in front when driving. * Avoid turning on
high beams. * Sound the horn in time to indicate your position.
Driving on icy and slippery roads
* When braking, step on the brake lightly to avoid continuous pressing on the brake for a long time.
Notice
* Avoid high-speed driving, sudden acceleration, sudden braking and sharp turns when driving, and
vehicles to maintain adequate clearance.
* Carefully apply deep braking when driving to prevent the wheels from locking.
Kind tips
* It is recommended to install snow chains to increase the mechanical braking force.
Winter Driving Essentials
Power battery performance
The performance of the power battery will decrease in a low temperature environment. If the vehicle is not used for a long time in winter,
you should pay attention to charging and maintaining the battery. Charge the battery to 100% SOC (state of charge) once a month and
then discharge it to 70%~80% to preserve the battery life.
78
Notice
* When the temperature of the power battery is lower than -35,* the power battery will not be able to charge and discharge. *
When the temperature of the power battery is between -35°C and -20°C, the power battery can be discharged but no
method to charge.
* When the temperature of the power battery is above -20*, the power battery can be charged and discharged.
power economy
At low temperature, the charging and discharging capacity of the power battery decreases, and the power performance of the vehicle decreases. With the operation of
the vehicle, the battery discharges and the temperature rises, and the power performance of the vehicle gradually returns to normal.
Braking System
before winter
* Maintain the dryer uniformly, replace the filter element of the dryer, clean or replace the dryer
Exhaust valve and muffler, and apply appropriate amount of lubricating grease.
* Check whether the condenser is working normally. When the air compressor is working, step on the brake to discharge the condensation.
water or gas in the vessel.
* Pull the pull ring/rope of the drain valve to drain the water in each air cylinder.
after winter
* Drain the air storage tank after the vehicle operation every day to avoid the air storage tank due to the accumulation of water and ice.
The drain valve core is blocked, resulting in air leakage.
* When the brake system is found to be frozen, refer to the following "Troubleshooting and Handling Methods",
Check the ice location and deal with it in time.
* Troubleshooting and handling methods
79
fault phenomenon Troubleshooting and treatment methods Brake
the drain valve of the air reservoir before and after operation, and check whether there is gas discharged
from the drain valve. If there is gas discharged, check whether the air pressure sensor is frozen. If it is
The air compressor is started, and the front and
frozen, use hot air to thaw the sensor. If there is no gas discharge, pour hot water or blow hot air to the four-
rear brake air pressure on the instrument does
circuit protection valve to thaw. Operate the water discharge valve of the parking air tank and check whether
not change or rises slowly
there is gas discharged from the water discharge valve of the parking air tank. If there is no gas discharge,
it is necessary to thaw the four-circuit protection valve and the pipeline between the four-circuit protection
valve and the parking air tank. If there is gas discharged, loosen the bolts of the rear brake air chamber,
and drive the car back to the pit for disposal.
Parking brake cannot be released
After the vehicle is started, an obvious sound

Generally, it is caused by the leakage of air after the water discharge valve freezes. Water the water discharge
of air leakage can be heard, the air pressure
valve to freeze or replace the water discharge valve.
rises slowly, and the air
compressor safety valve is activated, and the

The low point of the pipeline in the front section of the rear cabin dryer is frozen and blocked, and the low
air compressor continues to make a "pop"
point of the pipeline is poured with hot water to freeze.
sound
Battery heating system (optional)
BYD truck battery thermal management system mainly heats the power battery through an independent water heater.
* Before winter
* Replace the appropriate type of coolant according to the ambient temperature of the operating site to avoid cooling at low temperatures.
Coolant freezing damages the battery thermal management system.
* Operate the switch of the water pump of the battery thermal management system to check whether the water pump is working and whether the water circuit is
No cycle is good.
80
* Check the coolant level of the water tank, and replenish the coolant to the highest level of the water tank (water
box opening).
* After winter
When the liquid level of the water tank of the battery thermal management system is low, the effect of the water circulation circuit will be poor. Therefore, pay attention to
check the liquid level of the water tank before starting the car every day, and replenish the coolant to the highest liquid level of t he water tank (at the mouth of the water tank).
heating system
At present, the heating of BYD trucks adopts PTC electric heating (referred to as electric heating). The operation precautions are as follows:
* Electric heating system
* Remove the obstructions from the air inlet and air outlet of the PTC radiator. * Turn on the electric
heating and check whether the PTC radiator operates normally.
charging equipment
At present, the working temperature range of the charging box is -25 * ~ 50 ,* but due to the development level of key components in the industry,
when using it in a low temperature and extremely cold environment, the following matters should be paid attention to:
possible failure Recommended Action
If conditions permit, it is recommended to install insulation measures on the charging box, such as (for charging
The electric box is equipped with a heating fan, and the charging box is covered with a thermal insulation object), charging box
Normal startup During the charging process, the insulation device needs to be removed.
Does not work well below -25°C

Charge the car in time after receiving it. For the use of grid trough periods (usually
22:00 to 6:00 the next day) charging area, due to the ambient temperature during this period
It is recommended to arrange the charging of the vehicle in advance after the vehicle is collected to reduce charging.
The case occurs when the box cannot work due to low temperature.
81
Try to heat the machine interface before the charging box vehicle starts.
The HMI cannot be started or
After the vehicle is started, set the HMI screen of the charging box to the long-bright mode
Operation failure
That's it.
The flexibility of the charging gun cable decreases. Do not bend the charging gun cable and pull it too hard.
If there is condensation and water inflow, please use a hairdryer or a heat gun to blow
Charging muzzle and vehicle socket have
Dry, the charging gun head has debris or condensation and water ingress is completely prohibited.
Condensation into water or other impurities
stop charging. In order to avoid damage to the charging box and safety accidents.
The shell of the charging box is fragile to avoid external impact on the plastic shell of the charging box.
Small animals such as (gecko, ant

Please open the charging box and power distribution box regularly (monthly) for inspection. (power distribution
ants, snakes) etc. will be removed from the charging case
After the box is checked, the power distribution box must be locked up and down to prevent rain, snow and small movements.
Drilling holes reserved for brush software

things enter)
to cause an electrical short circuit
Other considerations
* The coolant has the correct antifreeze protection.
* Use the coolant recommended by BYD, and select a suitable coolant according to the ambient temperature of the operating location.
Coolant model.
* Use the wiper detergent recommended by BYD, and choose a suitable wiper according to the ambient temperature of the operating area.
suitable wiper detergent model.
* Use the gear oil of the rear axle reducer recommended by BYD, according to the ambient temperature of the operating place.
Select the appropriate type of rear axle reducer gear oil.
* Check the battery for winter use.
82
*The high and cold environment in winter will reduce the power of the battery, so the battery should be kept
Sufficient power for winter vehicle start.
*After the vehicle runs on the day, it is recommended to charge it immediately.
*When the vehicle fails during operation, the problem should be solved as soon as possible to avoid long-term parking.
As a result, the temperature of the power battery is lowered, and the vehicle start operation cannot be performed.
*After the vehicle is powered off, please place the smart key in an environment above -18°C.
* When the battery temperature of the smart key is lower than -18°C, it will not work normally, and the vehicle will fail to start.
effect. At this time, you can try other vehicle startup methods, please refer to 5-1 for details.
in "If the smart key battery is exhausted".
3-11. Driving assistance system
ABS (Anti-lock Braking System)
Features
This vehicle is equipped with ABS (Anti-lock Braking System) which can prevent the wheels from locking when braking, to improve
the stability and steering control performance of the vehicle. The ABS brake pressure adjustment process is realized through
autonomous control, and does not require additional operation by the driver.
Kind tips
*The conventional braking system still works when the ABS fails. *
When the vehicle accelerates above 10km/h, the ABS system starts to work and decelerates
When it is below 5km/h, it will stop working.
* Depressing the brake pedal on wet and slippery roads such as manhole covers and steel plates in rainy days will automatically activate
ABS system.
*Brake pedal vibration may be felt and noise may be heard when the ABS system function is activated.
At this time, press the brake pedal slightly, ABS can work normally.
83
Notice
* After the vehicle is started, if the ABS system fails, the
The ABS indicator light will come on. The anti-lock braking function will be disabled. At this time, it is necessary to take
corresponding cautious driving methods, and immediately notify BYD sales and service personnel or drive the car to the
repair station designated by BYD in time for maintenance.
Brake priority function
The brake priority function is a function that only responds to the brake signal when the vehicle accelerator signal and the brake signal appear at the
same time. That is, the vehicle has no power output in the following two situations:
1. When the vehicle is in D or R gear, depress the accelerator pedal and brake pedal at the same time. 2. Apply the parking
brake and press the accelerator when the vehicle is on the parking brake.
The vehicle can start only by stepping on the accelerator when there is no brake signal input.
Regenerative braking function
The regenerative braking function is that when the vehicle is braking, the driving motor changes to the generator condition, and the kinetic energy is
converted into electric energy and stored in the battery. Brake feedback can effectively improve driving safety and reduce the pressure on traditional
braking systems. It can improve the driving mileage of the vehicle and save energy consumption.
3-12. Driving Essentials
new car running
The correct running-in of the new car has a great relationship to prolong the service life of the vehicle and improve the reliability of the vehicle
operation. Our company recommends that a new car or a vehicle with new transmission system components (such as drive motor, wheel hub
bearing, etc.) be replaced within the first 5000km for the running-in period.
The following regulations should be observed during the new car run-in period
84
* Drive on flat, hard, solid surfaces with low gradients throughout the run-in period. * Drive safely, try to avoid sudden
acceleration and sudden braking. * Pay attention to the temperature of the drive motor, hub and brake.
The cause should be found and adjusted or repaired.
after walk-in
After running-in, follow the running-in maintenance items.
Kind tips
* When the vehicle is used for the first time, it is necessary to perform an operation of fully charging and then discharging the battery (ie,
fully discharging) to make the SOC accurate. The recommended full discharge operation is: SOC at 20%
When the car is moved to the charging pile, turn on the air conditioner to heat, and discharge until the high voltage is cut off.
energy efficient driving
* Energy-saving driving skills:
1. Start at a low speed, accelerate slowly and steadily, and avoid abrupt starts.
2. Drive at a constant speed, keep the accelerator pedal as still as possible, avoid unnecessary parking or braking, and keep a proper driving
distance from the vehicle in front to avoid emergency braking and use energy reasonably.
3. Avoid high-traffic or traffic-congested areas as much as possible.
4. After exceeding the economical speed, the faster the speed, the greater the wind resistance, the more power consumption, and the better the control.
The maximum speed and maintaining the speed properly can save energy.
5. Improve energy recovery. During the deceleration process of the vehicle, try to use the sliding mode to decelerate to facilitate the recovery
of electric energy. When there is no need for emergency braking, release the accelerator pedal and step on the brake pedal lightly
to facilitate the slow braking function of the motor.
Notice
* When braking in an emergency, the driver must depress the brake pedal as quickly as a conventional vehicle.
85
boards to ensure the safety of pedestrians and vehicles.
6. Before turning on the air conditioner in summer, the windows should be opened to let the hot air dissipate. When driving, the windows should be closed tightly.
Generally, the air conditioner should be set at 26°C; when the temperature is not high, use the ventilation mode.
7. Maintain normal tire air pressure; when the air pressure is high, the power consumption will be lower, but the tire life will be shortened and the adhesion will
be reduced, so it is necessary to choose the tire and tire pressure correctly.
8. The wheels should be kept in the correct position, otherwise it will cause the tires to wear too fast, the powertrain load will increase, and the power will be
consumed.
9. When parking for a long time, press the gear N button, switch to neutral, and apply the handbrake.
10. It is recommended that the vehicle be powered off when the vehicle is parked for more than 15 minutes.
86
Chapter 4 After Driving
4-1. Charging
DC
1. When the power battery is low, the power battery charging status indicator on the meter lights up,
The power battery needs to be charged, and the charging must be done at the charging station designated
by BYD. 2. When charging, the parking brake handle must be pulled up, the person in the car leaves, and the vehicle key
in an inactive state.
3. Connect the charging cable to the charging port.
4. After the charging gun is connected, the indicator light can be observed on the meter.
5. Click "Start" on the display of the charging cabinet or swipe the card to start charging. At this time you can
Observe vehicle SOC, charging voltage, current, etc.
6. Time to fully charge the power battery: about 1.5h, subject to the remaining time displayed by the meter.
7. Stop charging: when fully charged, the charging cabinet will automatically end charging; or swipe the card to disconnect the charging
electricity; or tap "Stop Charging" on the display of the charging cabinet.
8. Pull out the charging gun, close the charging port cover and the charging port hatch.
87
charging port
Notice
*Please choose to charge in a relatively safe environment (such as avoiding liquid, fire, etc.
territory).
*It is strictly forbidden to modify or disassemble the charging port and charging equipment, which may cause charging failure,
cause a fire.
*Before charging, please ensure that there is no water or foreign objects in the vehicle charging port and charging connector port.
And the metal terminals are not rusted or corroded, otherwise charging is not allowed. Improper terminal connection may
cause short circuit or electric shock, which is life-threatening.
*If you notice a strange smell or smoke coming out of the car while charging, stop charging immediately. *After charging, do
not disconnect the charger with wet hands or while standing in water, because this
It may cause electric shock and cause personal injury. *
In order to avoid damage to the charging equipment:
*Do not close the charging port hatch with the charging port cover open; *Do not pull or twist
the charging cable forcibly;
88
* Do not subject the charging device to shock; * Do not store
or use the charging device in an environment with a temperature higher than 50°C;
* Do not place the charging device near a heat source.
* When charging, people are not allowed to stay in the vehicle. * When
charging, it is recommended to park the vehicle in a ventilated place. * When
charging, the all-in-one on the right side of the frame is in working state, and the relay will be sent out several times at this time.
A "click" sound when the device is closed is normal.
* When the power battery is fully charged, the system will automatically stop charging. * When stopping
charging, first stop the output of the charging cabinet, and then disconnect the charging gun. * Before starting
the vehicle, please make sure that the charging gun is disconnected, the charging port cover and the charging port hatch are closed, because
the vehicle may be powered on and can be driven in gear when the charger locking mechanism is not completely locked. Damage to
charging equipment and vehicles. charging port cover
If it is not closed, water or foreign substances may enter the charging port terminal, affecting normal use.
* When the ambient temperature is lower than 0°C, the charging time is longer than normal, and the charging capacity is
Low.
* If the vehicle is not used for a long time, in order to prolong the service life of the power battery, it is recommended that every 3
Charge and drive once a month.
* The charging port needs to be maintained regularly according to the maintenance requirements. It is recommended to perform maintenance every 2 months.
1 time.
4-2. Overhaul the power-off device
Function
It is used to manually disconnect the high-voltage circuit during maintenance and emergencies.
89
Location
The location is as shown in the figure:
Danger
* During the normal charging and discharging process of the vehicle, it is strictly forbidden to plug and unplug the power-off device and low-voltage plug.
pieces.
* In non-emergency situations, when it is necessary to disconnect and repair the power-off device, ensure that the vehicle is powered off, and check the
meter to confirm whether the vehicle displays the words "smart charging". Charging; if the vehicle is not in intelligent charging, you can directly
disconnect the maintenance power-off device.
* If the handle of the vehicle maintenance power-off device is unplugged, it is strictly forbidden to insert the handle of the maintenance power-off device
in the state of high and low voltage. * Before reinserting the handle of the maintenance power-off device, check that the handle and the body
of the maintenance power-off device are correct.
Make sure it is dry and free of dust before reinserting.
* If there is a special accident, such as electric leakage, electric shock and other emergencies, you can unplug the handle of the maintenance power-off
device and notify the BYD sales and service personnel deal with vehicle failures, and are strictly prohibited from reconnecting and repairing
the power-off device.
* If the maintenance power-off device is ablated due to a fault, it cannot be used continuously, and simultaneously check whether the related components
of the maintenance power-off device are damaged. If it is damaged, it must be replaced as soon as possible.
90
If the main body of the power-off device is normal, replace the handle as soon as possible. * The
vehicle should be operated in strict accordance with the requirements of this manual during the use of the vehicle. It is strictly forbidden to plug
and unplug the power-off device without permission. If the power-off device or other high-voltage components of the vehicle are
damaged due to illegal operations, and a safety accident is caused, the corresponding responsibility shall be borne.
91
4-3. Trailer device
front tow hook
Swivel front tow hook lever
When using the front tow hook, unscrew the front panel of the cab, screw the front tow hook rod into the support, and screw it together.
To the leakage of 3-5 teeth of the tie rod, ensure that the lifting lug surface of the tie rod is in a horizontal or vertical state.
traction
When the vehicle is running normally, the tow bar can be removed; when the vehicle is being towed by other vehicles,
The pull rod is screwed into the front tow hook support; the traction rope is inserted into the front tow hook pin, the tow hook pin is inserted into the tow
hook pull rod, the opening pin locks the tow hook pull rod, and then the vehicle can be towed; when the vehicle is rescued by the trailer, according to the
rescue The actual condition of the car tow.
Slip on the tow rope
When using the front tow hook, the tow rope is threaded into the tow hook.
4-4. Backup power
Backup power supply (optional)
92
Open the power supply cover
4-5. Disconnect the high voltage circuit
DC ± high voltage connectors are used for manual disconnection of high voltage circuits during maintenance and emergency situations.
DC±HV connector position
The location of DC ± high voltage connectors is shown in the figure:
DC ± high voltage connector disconnection operation
93
(a) closed state
(b) Separated state
Danger
* During the normal charging and discharging process of the vehicle, it is strictly forbidden to connect DC ± high voltage connectors and low voltage connectors.
pieces.
* In non-emergency situations, when it is necessary to disconnect the DC ± high-voltage connectors, ensure that the
vehicle is in a power-off state, and check the meter to confirm whether the vehicle displays the words "smart charging".
94
Similarly, if the vehicle is in intelligent charging, it should be released first; if the vehicle is not in intelligent charging
In power, you can directly unplug the DC ± high voltage connector.
* If the DC ± high voltage connector of the vehicle is unplugged, make insulation protection, and it is strictly forbidden to
Insert the DC ± high voltage connector in the high voltage state.
* Before reinserting the DC±HV connector, check the handle and the DC±HV connector pair.
Make sure it is dry and free of dust before reinserting.
* If there is a special accident, such as electric leakage, electric shock and other emergencies, you can unplug the DC ± high
voltage connector after taking protective measures (wearing insulating work clothes with a withstand voltage of more than
1 000 V, insulating gloves, and insulating rubber shoes). And notify the BYD sales and service personnel to deal with the
vehicle failure, and it is strictly forbidden to insert the DC ± high voltage connector again.
* If the DC ± high voltage connector is ablated due to a fault, it cannot be used any more, and simultaneously check whether the
related components of the DC ± high voltage connector body are damaged. If it is damaged, replace it as soon as possible;
if the DC ± high voltage connector is normal, replace it as soon as possible ±High voltage connector.
* The vehicle should be operated in strict accordance with the requirements of this manual. It is strictly forbidden to insert and unplug the DC ±
high-voltage connectors without permission. If the DC ± high-voltage connectors or other high-voltage components of the vehicle are
damaged due to illegal operations, resulting in a safety accident, you must bear the corresponding responsibility. responsibility.
95
Chapter 5 When something goes wrong
If the vehicle won't start
* Check items:
Check whether the main power switch is closed;
Check that the battery is fully charged.
After the above checks, if the vehicle still cannot be started normally, the vehicle control system may be faulty, please
contact BYD sales and service personnel.
If the vehicle cannot be driven after starting
* Check items:
Check if the meter OK light is on;
Check whether the charging gun is disconnected;
Check whether the vehicle instrument gear is displayed as D or R;
Check that the parking brake light is off.
After the above inspection, if the vehicle still cannot be used, please contact BYD sales and service personnel.
If the vehicle has no power output during driving
* Check items:
* Turn on the emergency warning
light; * Slowly reduce the speed, carefully drive the vehicle away from the motor vehicle lane, and park in a
safe place; * Power on and try to start the vehicle. If the vehicle starts normally, please drive the vehicle to BYD
Sales service store; if it cannot be started, please contact BYD sales and service personnel.
If EV functionality is limited
96
Motor and motor controller overheating
* Check items:
Turn on the emergency warning light;
Slowly reduce the speed, drive the car carefully out of the motorway, and stop to a safe place;
Check whether the liquid level of the expansion tank is normal;
If the liquid level of the expansion tank is within the normal range, please contact BYD sales and service personnel.
Notice
* Hands and clothing should be kept a certain distance from the cooling fan to prevent
damage.
* W hen checking the liquid level of the expansion tank, care should be taken to prevent personnel from being scalded by the high-temperature coolant sprayed out.
hurt.
To stop in an emergency
In the event of an emergency, the vehicle can only be parked according to the following steps:
1. Turn on the emergency warning light, and at the same time press the brake pedal firmly with both feet,
Depress the brake pedal repeatedly, otherwise it will increase the force required to slow down the vehicle.
2. Shift to N position.
3. Park the vehicle in a safe place after the speed has decreased.
4. Apply the parking brake.
Kind tips
* When stopping the operation in an emergency, do not panic to avoid misoperation.
Power off the vehicle in an emergency
97
*If the high -voltage components such as the drive motor and all-in-one work abnormally, avoid continuing to drive, pull over to
the side, pull out the maintenance power-off device, and contact BYD sales and service personnel.
*If there is abnormal noise or smell in the battery pack box, pull over immediately and pull out the battery.
Repair the power-off device and contact BYD sales and service personnel.
If the vehicle encounters heavy rain, wading
*When the vehicle is driving, try to avoid wading in water. When the road water depth exceeds
When it is 250mm or when the wading road is more than 500m, you should drive around the wading road.
*In the process of wading, drive at a slow speed, with a speed of 1* 5km/h, and pay attention to the
Check whether the instrument has sound and light signals such as fault alarm.
*In the process of wading, if there are abnormal phenomena such as fault alarm, the driver should drive the vehicle away from
the water-filled road to a safe place as soon as possible, operate the parking brake switch, start the parking, stop the
power off, and unplug the maintenance power-off device. , and BYD sales service person
staff contact.
If a car trap occurs
If the wheels or vehicle get stuck in snow, mud or sand, take the following actions:
*Pull up the parking handle and set the gear to “N”; * Clean up the snow,
mud or sand around the trapped wheels; * Put wood, stone and other auxiliary
traction materials under the wheels; * Change the vehicle gear Move to R or D, release the
parking brake, and accelerate to move the vehicle away.
Danger
*If you choose to swing the vehicle back and forth to move away, please make sure that there are no other vehicles, objects or
people around to avoid accidental injury. *When the vehicle is out of the trap, it will suddenly rush forward or backward, so be very
careful.
98
Notice
To prevent damage to other components such as the motor and motor controller, observe the following precautions
when moving the vehicle:
* If the accelerator pedal is pressed all the way and the wheel still cannot turn, avoid pressing the accelerator pedal frequently.
speed pedal.
* If the vehicle cannot be freed from the trap after moving back and forth several times, you need to use towing, etc.
other methods.
If the vehicle needs to be towed
If the vehicle is stuck and needs to be towed
Take the following actions:
Notice
* When towing, the driver must drive the vehicle inside the vehicle. * Use a rigid
tow bar to tow the vehicle. * The towing speed is prohibited to exceed 30km/h. *
When towing, be sure to engage the mechanical neutral gear and turn off the hill
start assistant function. * How to release the parking brake: Release the parking brake and put the handle to the
lowest position to release the parking brake.
car braking. If you cannot get the vehicle out of the trap after moving back and forth several times, you need to use
Drag and drop and other methods.
Vehicle towing steps:
99
1. Remove the tow hook from the
vehicle kit
2. Take it off at the front right
position of the cab
The tow hook cover,
as shown in the
figure, is inserted into
the gap between the
bottom of the tow hook
cover and the front
1. Driving Trailer Hole Covers

protection, and gently pry it
Lift the tow hook cover.
3. Tow hook thread one
side alignment tow hook
Bracket mounting holes
Turn clockwise to
Bottom can be.
100
1. Bracket mounting holes
4. Tow hook as shown in circle
shown in
1. Tow hook
5. Slide the towing ring onto the
tow hook
6. Release the brake pedal
before towing
If the vehicle breaks down and needs to be towed
When the vehicle breaks down, the towing ring can be put on the tow hook in front of the right side member of the vehicle frame to
temporarily tow the vehicle. Use caution when towing the vehicle.
Vehicle towing steps:
101
* The position of the front tow hook is as
as shown
* Open the right trim panel of the cab front bumper
* Set-in and release
If the vehicle is exposed to standing water
If the vehicle is immersed in water due to an accident, the following operations are required:
* Do not start the vehicle, and notify BYD sales and service personnel. * After the vehicle was parked
for 48 hours, there was no abnormality (smoke, high temperature, electric spark,
Burnt smell, etc.) before entering the workshop for maintenance.
* Maintenance personnel must be professionally trained by the manufacturer and hold an electrician operation certificate.
If the tire is flat
* 1. Turn on the emergency warning light; * 2.
Slowly reduce the speed, carefully drive the car away from the motor vehicle lane, park in a safe place, and shift the
When the position is in the "N" gear, the vehicle cuts off the high voltage;
* 3. Pull on the handbrake and contact the emergency repair personnel.
102
Notice
* Do not continue to drive with flat tires, so as not to damage the tires and wheels, so that the
repair.
Tire Replacement Procedure
* Repair personnel must carry spare tires, hydraulic jacks, tool boxes, etc.; * Use
triangular wood to block the wheels; * Loosen the wheel nuts.
Replacing the front wheel: jack up the front axle as shown in the figure.
Change the position of the front wheel jack
Replacing the rear wheel: jack up the rear axle as shown in the figure.
103
Replacing the rear wheel jack placement
* Jack up the vehicle
After confirming that no one is in the vehicle, jack up the vehicle to a height where the spare tire can be installed.
Danger
When jacking up the vehicle with a hydraulic jack, be sure to observe the following precautions to prevent personal
injury:
* Park the vehicle on a flat, firm surface, pull up the parking handle, and place a triangular log under the tire. * Use a jack of 5
tons and above, and follow the jack's operating instructions. * Use the jack to jack up the vehicle only when changing the
wheels. * Make sure to place the jack in the correct position. Incorrect placement of the jack may damage the vehicle or cause
the vehicle to fall, resulting in personal injury. * Do not jack up the vehicle when there are people in the vehicle. * Do not start
or run the motor when jacking up the vehicle. * When using the jack, it is forbidden to place sundries above or below the jack.
* Loosen wheel nuts must be removed after the vehicle is jacked up. * Do not place any part of your body under the vehicle
when the vehicle is only supported by the jack.
104
cause personal injury.
battery location
The location of the battery is shown in the figure:
If the vehicle battery is depleted
If the vehicle battery is low enough to start the vehicle, you can temporarily start the vehicle by following these steps:
Connect a 24V DC power supply with an output current of at least 20A in parallel at the positive and negative poles of the battery, and
then perform the power-on operation. The power supply gear should reach the OK gear state.
After the above operations, please contact BYD sales and service personnel to confirm whether the battery needs to be replaced.
Notice
* Use a 12V charger to supplement the battery. Do not connect two batteries in series.
Row.
* The charging environment temperature should not be higher than 40*.
* During the charging process, when the battery temperature exceeds 45°C, stop charging until the battery temperature is reached.
105
After cooling down to room temperature, halve the charging current and continue charging.
* When a single battery is damaged, the two batteries on the same vehicle should be replaced together.
* Charging the battery when the battery cable is not disconnected may seriously damage the electronic control unit and electrical
equipment of the vehicle. Therefore, the battery cable should be removed before connecting the battery to the charger.
* If the high-voltage electronic control assembly is not working, using the vehicle's electrical equipment for a long time may
cause the battery to be over-discharged, making the vehicle unable to start, or even permanently damaging the battery.
warn
* Avoid battery fire or explosion
Batteries may release flammable gas, please observe the following precautions to prevent accidental ignition of gas.
* Make sure that each jumper cable is connected to the correct terminal and that the jumper cable does not
Accidental contact with a part other than the correct terminal.
* Do not allow the jumper cable to touch the (+) clip and (-) clip at the same time. * Do not smoke or
ignite near the battery.
* Precautions for battery
Batteries contain toxic and corrosive acidic electrolytes, and related parts also contain
Contains lead and lead compounds. Observe the following precautions when handling batteries:
* When operating the battery, be sure to wear safety goggles and be careful not to let any battery
Battery electrolyte (acid) has come into contact with skin, clothing, or bodywork.
* Do not attach to the battery. * If the battery
electrolyte comes into contact with the skin or eyes, immediately wash the contact area with water and seek medical
attention. Before your visit, apply a damp sponge or cloth cover
106
Hold the contact area.
* Always wash your hands after handling battery brackets, terminals, and other battery-related parts.
* Keep children away from the battery.
If the key is lost
Please contact BYD sales and service personnel.
If the smart key battery is exhausted
Do the following:
Replace the smart key battery in time;
When unlocking/locking the door, it can only be operated with the mechanical key;
When you need to start the vehicle, put the smart key in the storage box with the key symbol;
If the above operations fail to realize the smart key function, please contact BYD sales and service personnel.
Inspection location
107
* The electrical inspection port is located at the lower right of the instrument panel body, open the glove box assembly
Pull out and disassemble diagonally upwards to expose the electrical inspection port for electrical inspection.
* After the maintenance is completed, the glove box can be assembled.
108
109
* The body inspection port is located under the seat cushion body, and the front seat cushion of the passenger middle seat is
Remove the two M8 bolts at the mounting points, and the tightening torque of the bolts and nuts is: 23
±2 N•m, pull out the middle seat cushion along the clamping direction, remove the cushion,
* Remove the four M6 bolts that fix the inspection cover, take out the cover, and conduct electrical inspection.
build.
* After the maintenance is completed, the maintenance cover and seat cushion can be restored and assembled.
110
Chapter 6 Vehicle Specifications
6-1. Vehicle parameters
Basic parameters of the vehicle
Length (A) mm (mm) 5930
Dimensions Width (B) mm (mm) 2120
Height (C) mm (mm) 2940
Front overhang (D) mm (mm) 1135
Rear overhang (E) mm (mm) 1435
Front (G) mm (milli

1690
Meter)
wheelbase
Rear (H) mm (mm) 1570
Wheelbase mm (mm) 3360
Approach angle * (degrees) 17

*
Departure angle * (degrees) 13

*
Minimum turning diameter m (meters) 13.16

*
111
Curb weight kg (kg) 2800
Maximum allowable total mass kg (kg) 6495
Front/rear axle allowable maximum axle load kg (kg) 2200/4500
Driving mileage km (km) (working condition method) 210
Maximum grade% 20
Maximum speed km/h (km/h) 100
0-50km/h acceleration time s (seconds)

8*
112
The following parts are not included in the vehicle outline dimensions:
1. Wipers: located on the upper dash panel under the front windshield;
2. Washer: located on the upper dash panel under the front windshield;
3. Rear suspension: located at the rear of the cab;
4. Front panel armrest: located on the upper trim panel of the front panel under the front windshield;
5. Front down-view mirror: located above the right side of the front windshield;
6. Door lock: located on the left and right doors;
7. Door handle: located on the left and right doors;
8. Outside rearview mirror and wide-angle mirror: located on the left and right doors;
9. Side turn signal: located on the front and lower sides of the left and right doors;
10. The deformed part of the tire wall: located just above the tire contact point;
11. The soft part of the antenna: located on the roof of the cab.
Chassis parameters
Chassis parameters
model TZ220XST (Integrated Bridge)
type Permanent Magnet Synchronous Motor
motor
Manufacturer Changsha BYD Automobile Co., Ltd.
Rated output power/Maximum output power

70/145
kW (kilowatt)
113
Rated output torque/maximum output

150/330
Torque N m (N m)
maximum speed
12000
r/min (revolution/minute)
Location horizontal/rear
front axle form 2.3T integral I-beam steering front axle
form
rear axle 4.5T BYD Integrated Bridge
frame form Variable section riveted frame
Suspension System form Longitudinal leaf spring non-independent suspension
steering system form Electric power steering
service brake front and rear drums
Parking brake air brake
Braking System
emergency braking parking brake system
auxiliary braking brake feedback device
Thickness of friction material in front of brake friction pair (mm) 12
114
Thickness of rear friction material (mm) 16
Front brake hub (mm) 310mm

*
Rear brake hub (mm) 310mm

*
Brake pedal free travel (mm) 10-15
Tire specification
(including spare tire) 7.00R16LT-14PR
Tire pressure (including

770±10
spare tire) kPa (kPa)
Front wheel 1°±30’
camber (°)
Front wheel total 1~3mm
toe (mm)
Wheel alignment parameters
Kingpin inclination 7°±1°
angle (°)
Kingpin camber (°) 3.5°±45’
115
6-2. Vehicle Identification
vehicle identification number location
Located in the front right position of the frame, it is used for vehicle registration and traffic bureau filing.
1* Vehicle Identification Number
Vehicle nameplate location
* The nameplate is located on the door pillar on the right side of the cab
1 nameplate
116
Motor identification location
1* Motor stamp position
Integrated bridge motor
•1 Motor nameplate
•2 Motor stamp
6-3. Main components of new energy
Power Battery
The power battery is generally charged through the charging cabinet, and the vehicle equipped with regenerative braking function can also
charge the power battery through the motor when braking or coasting.
Power battery temperature characteristics
-205*5*(charging)
Working temperature
-305*5*(d ischarge)
117
Storage ambient temperature -405*0* 153

* 5*
The best working temperature of the battery
Notice
* If the vehicle has not been operated for more than 15 days, the vehicle must be fully charged before it can be put into
operation. * For vehicles equipped with heating function, if they are stored for more than 3 days in a low temperature - 10 * environment, they
need to be started before being put into use, so that the heating function of the whole vehicle battery is activated.
* If the vehicle is not in operation within a short period (two days), the power of the vehicle must be confirmed before use. After startup, if the
SOC of the meter is above 50%, the total operating mileage can be directly operated without charging within 30km. If conditions permit,
it can be fully charged before operation. If the SOC of the meter is below 30%, it needs to be fully charged before it can be put into use.
* Before the vehicle is operated, it needs to stand for one minute after starting to confirm that the instrument has no fault icon, no fault
The fault alarm means that the vehicle is in a normal state and can be operated.
* If the meter shows that the SOC is lower than 20% while the vehicle is driving, do not continue long distances.
For operation, the vehicle needs to be driven to the nearest charging station for charging.
* When the vehicle is running, if the meter reports that the power battery is faulty, please pull over and stop
Contact BYD sales and service personnel to deal with it.
* If the ambient temperature continues to be low (0°C and below), after the vehicle operation stops,
Please charge as soon as possible to avoid the battery temperature dropping in a low temperature environment and then increasing the charge
time, affecting the normal operation of the vehicle.
* When the power battery is in a normal state, due to factors such as driving habits (such as frequent acceleration and deceleration), road
conditions (such as going up a long slope), air temperature (such as low temperature), and whether the electrical equipment (such as
air conditioner) is turned on or not, the vehicle's The cruising range will fluctuate.
warn
118
* If the vehicle is subjected to a strong collision while driving, stop the vehicle in a safe area and check the
Check the chassis, front and rear battery areas of the body for damage. * When the
electrolyte leaks, do not touch it; if it accidentally touches the skin, use it immediately.
Wash with plenty of water; in case of eye contact, immediately wash with plenty of boric acid solution, and immediately
i.e. seek medical attention.
* After the vehicle is repainted, it needs to enter the paint booth
* If the temperature of the paint-baking room reaches 60*, the paint-baking time in the vehicle paint-baking room shall not exceed
4 hours, and a maximum of one paint finish is allowed every six months.
* If the temperature of the paint-baking room exceeds 60*, the battery pack must be removed before paint-baking.
Otherwise, the battery will be damaged.
Power battery recycling
* When the power battery of the new energy vehicle needs to be repaired and replaced, please follow the following procedures: 1. Send the vehicle
to a BYD service outlet, and the service outlet will check the information of the owner of the new energy vehicle.
information, and confirm whether the vehicle battery needs to be replaced.
2. Replace the power battery according to the corresponding steps and requirements in the maintenance manual.
3. The replaced power battery will be recycled by service outlets.
* When the new energy vehicle meets the scrapping requirements, please follow the following procedures: 1. Send the
vehicle to the BYD recycling network, and BYD will evaluate the residual value of the power battery.
And check the information of the owner of the new energy vehicle.
2. Send the evaluated vehicle to a scrapped car recycling and dismantling enterprise to disassemble the power battery.
3. Hand over the used power batteries of the car recycling and dismantling mechanism to the service outlets, service outlets
The power battery will be repurchased.
Kind tips
119
* If there is no local BYD recycling network, please contact BYD sales and service personnel to deal with it.
Notice
* Register and take pictures of the vehicle that replaces the power battery, and enter its basic information (vehicle information, power battery
information, unified coding information) into the information traceability system.
system and stick a label in a prominent position on the body.
*The disassembled power battery needs to be registered and entered into the information traceability system, and a paper file should be established
files and electronic databases, and the paper files will be transferred with the power battery after backup.
* Remaining site requirements, equipment and facilities requirements, personnel requirements, work requirements when removing the power battery
The remaining requirements for business requirements, temporary storage and management shall be implemented in accordance with local regulations.
* The failed battery to be replaced should not be placed sideways, upside down, or stored for a long time. If it needs to be stored for a short
time, it should not be stacked in the open air. Safety inspection and treatment should be carried out before storage, and storage
should be classified according to different categories. If there is leakage or leakage of electricity, it should be stored in a special
storage container with insulation and anti-leakage. Liquid or leakage can be stored in general packaging containers.
warn
* The battery repair and replacement site should be kept away from fire sources, avoid direct sunlight, and prevent fires caused by electrolyte
leakage.
* Electrolyte leakage and battery combustion gas will irritate eyes, skin and throat,
Therefore, if the damaged power battery is repaired or replaced, a protective mask is required.
* Do not touch the leaked electrolyte. If you touch it accidentally, wash it with plenty of water immediately.
In case of eye contact, wash promptly with plenty of boric acid solution and seek medical attention immediately.
* The owner of the new energy vehicle has the responsibility and obligation to hand over the used power battery to the recycling service
network. Privately hand over the waste power battery to other units or individuals, and disassemble or disassemble the power
battery privately, thereby causing environmental pollution or safety accidents, you must bear the responsibility
120
corresponding responsibility.
Vehicle Controller
Function
According to the driver's intention, vehicle status, working conditions and other factors, the control strategy is calculated to complete the control
and energy management of the policy power system, such as forward, reverse and system energy consumption optimization.
Integrated controller
Function
The integrated controller is an integrated controller system integrating drive controller, bidirectional DC controller, leakage sensor, AC and DC
charging, etc. It has charging, power distribution, energy feedback, drive electronic control, auxiliary electronic control, and leakage detection
and other functions.
121
motor
Function
It drives the vehicle to drive, converts electrical energy into mechanical energy, and converts kinetic energy into electrical
energy during braking or coasting, and acts as a retarder during braking. (Pictures have been added)
122
abbreviation
ABS Anti-lock braking system ACC adaptive cruise control
system
ASR Drive anti-skid system AEBS automatic emergency braking system
mall Panoramic Surround View System AVAS Low-speed beep system
CMS Collision Warning System ADAS Advanced Driver Assistance Systems
DMS Driver Behavior Monitoring CDP Deceleration control system
ECAS Electronic Air Suspension System EBS Electronically controlled braking system
EHPS EPS Electronic power steering system

Electro-hydraulic power steering
system
ECU Electronic Control Unit ESC Electronic Stability Control
FCW Forward Collision Warning EPB Electronic parking
LDW Lane Departure Warning HMW Vehicle distance monitoring and warning
PCW Pedestrian Collision Warning MPX Multiple control system
SOC battery percentage NOT Park assist system
TSR Traffic Sign Recognition TPMS Tire pressure monitoring system
123
COME Vehicle Identification Code V2L car to row discharge
124

BYDT45C01 User Manual

Uploaded by

Copyright:

Available Formats

BYDT45C01 User Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BYDT45C01 User Manual

Uploaded by

Copyright:

Available Formats

Data Class: Confidential

BYD T45C01 pure electric truck

Commercial Vehicle Research Institute

February 22, 2022

contact BYD sales and service personnel for confirmation.

* Refers to providing necessary additional

damage or cause damage to the vehicle.

even lead to death.

diagrams and are for reference only.

Copyright by BYD Auto Industry Co., Ltd.

Overview of BYD T45C01 pure electric truck

as e-commerce, express delivery, moving, postal service, and cold chain.

* High voltage safety

Vehicle technical highlights

stable, efficient and safe operation of the vehicle.

development process, the "ferroelectricity" was frequently

* Integrated bridge driver

* Battery management system

discharged and charged.

* Battery thermal management system

Pool, improve driving safety and driving mileage.

Record and store status information such as settings.

4G module, air conditioning panel and voice recognition (optional), etc.

kind of Visual enjoyment, family-oriented modeling to create brand recognition.

technology and a sense of security

Come for luxurious visual enjoyment, full of technological futuristic sense

open the future

Effectively reduce driving fatigue.

The driving experience is smoother;

Engineering design, wide field of vision;

and intelligent voice control to improve the driver's driving experience;

Real-time monitoring of vehicle status;

The user has widened t he space in the cabin;

warm and comfortable;

Fast, safe and reliable;

*EPS: Electric power steering, easy to operate and easy to maintain.

working environments, ensuring the safety of drivers and after-sales service.

1.5 hours, high charging efficiency;

of the vehicle and give customers more returns;

Service, the user's caring butler.

Reduce energy consumption and effectively reduce driving fatigue.

Overview of BYD T45C01 Pure Electric Truck .................................. 3

Table of contents. .........................................................................................9

Chapter 1 Safety Precautions ...................................................................................... 16

1-1. Safety Regulations ........................................................................................................... 16

1-2. Layout of high-voltage lines. ................................................................................................ 16

1-3. Restraining device ............................................................................................................18

Seat Belt Use and Adjustment .................................................................................. 18

1-4. Precautions for vehicle fire protection. ........................................................................................ 19

Electrical system fire causes and precautions ................................................................................. 19

CHAPTER 2 BEFORE DRIVING .............................................................................21

2-1. Key information............................................................................................................21

smart key. ............................................................................................................21

2-2. Main power switch. .................................................................................................. 22

Main power switch position ............................................................................................... 22

2-3. Opening, closing and locking the doors.......................................................................................24

Door locks. .................................................................................................................................................. 24

2-4. Inspection before driving .......................................................................................................25

Check before power-on. ........................................................................................................................................25

Wiper and washer fluid fill ................................................................................................................ 26