Test de Presion de Aceite 3126

3126E Truck Engine 9SZ00001-UP(SEBP3385 - 33) - Sistemas y componentes Página 1 de 8
Engine Oil Pressure - Test

SMCS - 1304-081
Measuring Engine Oil Pressure
Work carefully around an engine that is running. Engine parts that are
hot, or parts that are moving, can cause personal injury.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during

performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop

Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Table 1
Required Tools
Part Number Part Name Quantity
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw... 20/10/2011
1U-5470 Engine Pressure Group

or or 1
198-4240 Digital Pressure Indicator
8J-7844 Adapter Fitting 1
3K-0360 O-Ring Seal 1
4M-5317 Terminal Bushing

or or 1
5P-2720 Probe Adapter
Illustration 1 g00296486
1U-5470 Engine Pressure Group
The 1U-5470 Engine Pressure Group measures the oil pressure in the system. This engine tool group
can read the oil pressure inside the oil manifold.
Note: Refer to Special Instruction, SEHS8907, "Using the 1U-5470 Engine Pressure Group " for
more information on using the 1U-5470 Engine Pressure Group .
Note: The engine oil pressure can also be measured by using an electronic service tool. Refer to
Troubleshooting for information on the use of the electronic technician.
Oil Gallery Plug
(1) Plug.
1. Install the 1U-5470 Engine Pressure Group into oil gallery plug (1) .
Note: Engine oil pressure to the camshaft and main bearings should be checked on each side of
the cylinder block at oil gallery plug (1) .
2. Start the engine. Run the engine with SAE 10W30 or SAE 15W40 oil. The information in the
engine oil pressure graph is invalid for other oil viscosities. Refer to Operation and
Maintenance Manual, "Engine Oil" for the recommendations of engine oil.
Note: Allow the engine to reach operating temperature before you perform the pressure test.
Note: The engine oil temperature should not exceed 115°C (239°F).
3. Record the value of the engine oil pressure when the engine has reached operating temperature.
4. Locate the point that intersects the lines for the engine rpm and for the oil pressure on the
engine oil pressure graph.
Engine Oil Pressure Graph
5. The results must fall within the "ACCEPTABLE" range on the chart. A problem exists when
the results fall within the "NOT ACCEPTABLE" range on the chart. The problem needs to be
corrected. Engine failure or a reduction in engine life can be the result if engine operation is
continued with oil manifold pressure outside this range.
Note: A record of engine oil pressure can be used as an indication of possible engine problems
or damage. A possible problem could exist if the oil pressure suddenly increases or decreases
70 kPa (10 psi) and the oil pressure is in the "ACCEPTABLE" range. The engine should be
inspected and the problem should be corrected.
6. Compare the recorded engine oil pressure with the oil pressure indicators on the instrument
panel and the engine oil pressure that is displayed on the electronic service tool.
7. An engine oil pressure indicator that has a defect or an engine oil pressure sensor that has a
defect can give a false indication of a low oil pressure or a high oil pressure. If there is a notable
difference between the engine oil pressure readings make necessary repairs.
8. If low engine oil pressure is determined, refer to "Reasons for Low Engine Oil Pressure".
9. If high engine oil pressure is determined, refer to "Reason for High Engine Oil Pressure".
Reasons for Low Engine Oil Pressure
NOTICE
NOTICE

containing fluids.

• Engine oil level is low. Refer to Step 1.
• Engine oil is contaminated. Refer to Step 2.
• The engine oil bypass valves are open. Refer to Step 3.
• The engine lubrication system is open. Refer to Step 4.
• The oil suction tube has a leak or a restricted inlet screen. Refer to Step 5.
• The engine oil pump is faulty. Refer to Step 6.
• Engine Bearings have excessive clearance. Refer to Step 7.
1. Check the engine oil level in the crankcase. The oil level can possibly be too far below the oil
pump supply tube. This will cause the oil pump not to have the ability to supply enough
lubrication to the engine components. If the engine oil level is low add engine oil in order to
obtain the correct engine oil level. Refer to Operation and Maintenance Manual, "Engine Oil"
for the recommendations of engine oil.
2. Engine oil that is contaminated with fuel or coolant will cause low engine oil pressure. High
engine oil level in the crankcase can be an indication of contamination. Determine the reason
for contamination of the engine oil and make the necessary repairs. Replace the engine oil with
the approved grade of engine oil. Also replace the engine oil filter. Refer to Operation and
Maintenance Manual, "Engine Oil" for the recommendations of engine oil.
NOTICE
Caterpillar oil filters are built to Caterpillar specifications. Use of an

oil filter not recommended by Caterpillar could result in severe engine
damage to the engine bearings, crankshaft, etc., as a result of the larger
waste particles from unfiltered oil entering the engine lubricating
system. Only use oil filters recommended by Caterpillar.
3. If the engine oil bypass valves are held in the open position, a reduction in the oil pressure can
be the result. This may be due to debris in the engine oil. If the engine oil bypass valves are
stuck in the open position, remove each engine oil bypass valve and clean each bypass valve in
order to correct this problem. You must also clean each bypass valve bore. Install new engine
oil filters. For information on the repair of the engine oil bypass valves, refer to Disassembly
and Assembly, "Engine Oil Filter Base - Disassemble".
4. An oil line or an oil passage that is open, broken, or disconnected will cause low engine oil
pressure. An open lubrication system could be caused by a piston cooling jet that is missing or
damaged.
Note: The piston cooling jets direct engine oil toward the bottom of the piston in order to cool
the piston. This also provides lubrication for the piston pin. Breakage, a restriction, or incorrect
installation of the piston cooling jets will cause seizure of the piston.
5. The inlet screen of the oil suction tube for the engine oil pump can have a restriction. This
restriction will cause cavitation and a loss of engine oil pressure. Check the inlet screen on the
oil pickup tube and remove any material that may be restricting engine oil flow. Low engine oil
pressure may also be the result of the oil pickup tube that is drawing in air. Check the joints of
the oil pickup tube for cracks or a damaged O-ring seal. Remove the engine oil pan in order to
gain access to the oil pickup tube and the oil screen. Refer to Disassembly and Assembly,
"Engine Oil Pan - Remove and Install" for more information.
6. Check the following problems that may occur to the engine oil pump.
a. Air leakage in the supply side of the oil pump will also cause cavitation and loss of oil
pressure. Check the supply side of the oil pump and make necessary repairs. For
information on the repair of the engine oil pump, refer to Disassembly and Assembly,
"Engine Oil Pump - Remove".
b. Oil pump gears that have too much wear will cause a reduction in oil pressure. Repair the
engine oil pump. For information on the repair of the engine oil pump, refer to
Disassembly and Assembly, "Engine Oil Pump - Remove".
7. Excessive clearance at engine bearings will cause low engine oil pressure. Check the engine
components that have excessive bearing clearance and make the necessary repairs.
Reason for High Engine Oil Pressure
NOTICE
NOTICE

containing fluids.

Engine oil pressure will be high if the engine oil bypass valves become stuck in the closed position
and the engine oil flow is restricted. Foreign matter in the engine oil system could be the cause for the
restriction of the oil flow and the movement of the engine oil bypass valves. If the engine oil bypass
valves are stuck in the closed position, remove each bypass valve and clean each bypass valve in
order to correct this problem. You must also clean each bypass valve bore. Install new engine oil
filters. New engine oil filters will prevent more debris from causing this problem. For information on
the repair of the engine oil filter bypass valve, refer to Disassembly and Assembly, "Engine Oil Filter
Base - Disassemble".
NOTICE
Caterpillar oil filters are built to Caterpillar specifications. Use of an

oil filter not recommended by Caterpillar could result in severe engine
damage to the engine bearings, crankshaft, etc., as a result of the larger
waste particles from unfiltered oil entering the engine lubricating
system. Only use oil filters recommended by Caterpillar.

Test de Presion de Aceite 3126

Uploaded by

Copyright:

Available Formats

Test de Presion de Aceite 3126

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Test de Presion de Aceite 3126

Uploaded by

Copyright:

Available Formats

3126E Truck Engine 9SZ00001-UP(SEBP3385 - 33) - Sistemas y componentes Página 1 de 8

Engine Oil Pressure - Test

Measuring Engine Oil Pressure

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

Care must be taken to ensure that fluids are contained during

Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop

Dispose of all fluids according to local regulations and mandates.

1U-5470 Engine Pressure Group

3K-0360 O-Ring Seal 1

4M-5317 Terminal Bushing

1U-5470 Engine Pressure Group

Oil Gallery Plug

Engine Oil Pressure Graph

Reasons for Low Engine Oil Pressure

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

Care must be taken to ensure that fluids are contained during

Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop

Dispose of all fluids according to local regulations and mandates.

• Engine oil level is low. Refer to Step 1.

• Engine oil is contaminated. Refer to Step 2.

• The engine oil bypass valves are open. Refer to Step 3.

• The engine lubrication system is open. Refer to Step 4.

• The engine oil pump is faulty. Refer to Step 6.

• Engine Bearings have excessive clearance. Refer to Step 7.

Caterpillar oil filters are built to Caterpillar specifications. Use of an

Reason for High Engine Oil Pressure

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

Care must be taken to ensure that fluids are contained during

Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop

Dispose of all fluids according to local regulations and mandates.

Caterpillar oil filters are built to Caterpillar specifications. Use of an

You might also like