Efaeci: Engine Fuel Emission Control System

ENGINE FUEL &
EMISSION CONTROL SYSTEM
SECTION EFaECi
CONTENTS
I I 1642 & TD42 I I
PREPARATION ....................................................................................................................
EF & EC- 3
I I TB42 I I
GENERAL DESCRIPTION .................................................................................................. EF & EC- 11
ENGINE AND EMISSION CONTROL OVERALL SYSTEM .......................................... EF & EC- 12
ENGINE AND EMISSION CONTROL PARTS DESCRIPTION ...................................... EF & EC- 18
CARBURETOR ..................................................................................................................... EF & EC- 22
CARBURETOR - Inspection and Adjustment .........................................................EF & EC- 29
CHECKING AND ADJUSTING IDLE SPEED, IGNITION TIMING AND
MIXTURE RATIO ................................................................................................................. EF & EC- 36
ALTITUDE COMPENSATION SYSTEM DESCRIPTION ................................................. EF & EC- 39
ALTITUDE COMPENSATION SYSTEM INSPECTION ....................................................EF & EC- 40
THROlTLE VALVE POSITION DETECTING SYSTEM INSPECTION (Only for
control of automatic transmission) ................................................................................. EF & EC- 41
MECHANICAL FUEL PUMP INSPECTION ..................................................................... EF & EC- 42
EXHAUST GAS RECIRCULATION (E.G.R.) CONTROL SYSTEM ............................... EF & EC- 43
EVAPORATIVE EMISSION CONTROL SYSTEM DESCRIPTION ................................. EF & EC- 44
EVAPORATIVE EMISSION CONTROL SYSTEM INSPECTION .................................... EF & EC- 45
POSITIVE CRANKCASE EMISSION CONTROL SYSTEM DESCRIPTION ................. EF & EC- 46
POSITIVE CRANKCASE EMISSION CONTROL SYSTEM INSPECTION .................... EF & EC- 47
AUTOMATIC TEMPERATURE CONTROL (A.T.C.) AIR CLEANER SYSTEM ............ EF 8. EC- 48
ANTI-AFTERBURNING CONTROL SYSTEM INSPECTION ........................................... EF & EC- 50
IGNITION CONTROL SYSTEM INSPECTION ............................................................... EF & EC- 52
I I TD42 I I
INJECTION SYSTEM ..................................................................................................... EF & EC- 59
IN-LINE TYPE INJECTION PUMP ................................................................................ EF & EC- 61
VE-TYPE INJECTION PUMP ....................................................................................... EF & EC- 89
INJECTION NOZZLE .................................................................................................... EF & EC-117
Contents (Cont'd)
BLEEDING FUEL SYSTEM ................................................................................................ EF & EC-122
FUEL FILTER ....................................................................................................................... EF & EC-123
CRANKCASE EMISSION CONTROL SYSTEM ............................................................ EF & EC-124
QUICK-GLOW SYSTEM ..................................................................................................... EF & EC-125
INJECTION PUMP CONTROL SYSTEM .......................................................................... EF & EC-133
I I TB42 & TD42 1 J

SERVICE DATA AND SPECIFICATIONS (S.D.S.) ..................................................... EF & EC-145
PREPARATION E!l
SPECIAL SERVICE TOOL
Tool number
Tool name Description
1612562SOO Checking fuel level

Level gauge
PREPARATION 1'11)421
SPECIAL SERVICE TOOLS
In-line type injection pump
Universal vise
@ KV11244872
Bracket . .
@ KV11244782
Bracket
PE type: @ + @
PES type: @ +@+ @
OK57916432
Timer wrench
Extractor
Tappet clamp
Delivery valve extractor

PREPARATION
Timer exrractor
Base assembly
Special wrench
Plunger insert
Nozzle holder
PREPARATION lz!El
KV 1 1257800
Nozzle
Securing stand
Timer coupling
..
Measuring device
plunger pre-stroke
PREPARATION pi
VE-type injection pump
~djustingdevice on vehicle
Tool number
Description
Tool name
- -. -. - - ---- - - - -- -- - - - - -
KV 1 1229352
Measuring device
(Set length of
plunger spring)
@ KV11229350
Holder
@ KV11229360
Nut
@ KV 11229370
Pin
@ KVI 1254410
Dial gauge
Disassembling and assembling tools

-
@ KV11244852
Universal vise
@ KV11244872
Bracket
@ KV11244792
Bracket
KV11229072
Insert device
KV11214110
Socket wrench for
delivew valve a23
KV11214270
Socket wrench for
governor pivot bolt
PREPARATION I~ D 412
regulating valve
Socket wrench for

distributor head plug
KV11229542
Feed pump holder
KV 1 1229852
"MS" measuring
&vice set
compensator)
"K" & "KF"

measuring device
Adjusting device on pump tester
KV 1 1281 036
Fixing stand
PREPARATION lE!!zJ
Measuring device
(Timer advance angle)
[ 8 4 0 m m (33.07 in)]
KV11229462
Extractor
(Disassembling of
regulating valve)
(Assembling of
regulating valve)
(Bosch type
DN12SD12T)
PREPARATION JTMZ]

Injection nozzle
- -
Tool number
Description
Tool name
KV 11289004
Nozzle cleaning kit
@KV11290012
Box
@~~11290110
Brush
@K~11290122
Nozzle oil sump
scraper
@ KV11290140
Nozzle needle tip
cleaner
@KV11290150
Nozzle seat scraper
@K~11290210
Nozzle holder
@ KV 11290220
Nozzle hole
cleaning needle
&
KV11292210
Nozzle centering
device
- ---
KV11290632
Nozzle oil a m p
-per
\
KV11290820
Nozzle mmaper
GENERAL DESCRIPTION - --
--
- ---
-
- -- -
ITi421
System Application
Destination Model except

Australia and
Australia model Gulf standard model
Gulf standard Major unit
models
T
M/T M/T AIT M/T A/T
Crankcase emission
X X X X X P.C.V. valve
control system
B.C.D.D. unit
Boost controlled B.C.D.D. control
deceleration device X X* 1 X X*1 X solenoid valve
(B.C.D.D.) Speed detecting switch
(MITI
Exhaust gas recirculation
control system - - - - E.G.R. valve
T.V.V. (2 port-type)
(E.G.R. control system)
Evaporative emission
control system
- X X X X Carbon canister
Automatic temperature Temperature sensor

opt X X opt Opt
control air cleaner system ,
vacuum motor
Automatic choke - X X - -
Fast idle actuator
(F.I. actuator)
X "2 X"2 - X *2 - F.I. actuator
Fast idle pot

(F.I. pot)
- - X'2 - X'2 F.I. pot
Altitude compensation
system opt - - Opt Opt Altitude compensator
X: Available -: Not available opt: Optional

* I : With solenoid valve
'2: With air conditioner model
ENGINE AND EMISSION CONTROL OVERALL SYSTEM !?
l El
Component Parts Location
F.I. pot or F.I. actuator

ENGINE AND EMISSION CONTROL OVERALL SYSTEM E!zl
System Diagram
Model except Australia and Gulf standard models
- _ ENGINE AND EMISSION CONTROL OVERALL SYSTEM D!!Zl
System Diagram (Cont'd)
Australia A/T model
ENGINE AND EMISSION CONTROL OVERALL SYSTEM Ipq
System Diagram (Cont'd)
Gulf standard A/T model
1-- - ,-+-- ----------

ENGINE AND EMISSION CONTROL PARTS DESCRIPTION 1 1
Throttle Sensor & Throttle Valve Switch (Only
for control of automatic transmission)
The throttle sensor is attached on the carburetor and actuates
in response to the accelerator pedal movement. This sensor is a
kind of potentiometer which transforms the throttle valve posi-
tion into output voltage, and emits the voltage signal to the A/T
control unit. In addition the sensor detects the opening and
closing speed of the throttle valve, and sends the voltage
idle switch change rate to the A/T control unit. The throttle valve switch
actuates in response to accelerator pedal movement.
SEF64SG
This switch has idle contact and full throttle contact. The idle
contact is used for automatic transmission control. It closes
when the throttle valve is positioned at idle and opens when it
is at any other position.
Air Temperature Sensor

The air temperature sensor is a bimetal valve type. It is located
inside the air cleaner to detect the temperature of intake air.
The bimetal valve closes to prevent fuel from icing during
engine warm-up. When the valve closes, the vent valve causes
the hot air duct side to activate. Manifold vacuum is then
transmitted to the vacuum motor in order to deliver hot air from
the hot air duct. As the engine progressively warms up, the
valve opens in response to cool air being drawn in from the
engine compartment. Manifold vacuum applied to the vacuum
motor then begins to discharge into the atmosphere. As a
result, the air vent valve closes to shut off the air passage
heated by the hot air delivered from the hot air duct.
E.G.R. Control Valve

The E.G.R. control valve controls the quantity of exhaust gas to
be led to the intake manifold through vertical movement of the
taper valve connected to the diaphragm, to which vacuum is
applied in response to the opening of the throttle valve.
ENGINE AND EMISSION CONTROL PARTS DESCRIPTION IT&P2I
Thermal Vacuum Valve (T.V.V.)
Thermal vacuum valve detects engine coolant temperature by
means of a built-in bimetal, and opens or closes the vacuum
passage which controls E.G.R. system.
Water ternmature Therrrur! vacuum E.G.R. system
Below 40 (104) Not activated

Above 40 (1041 Activated
i
ldle Compensator
The idle compensator is basically a thermostatic valve which
introduces air directly from the air cleaner to the intake manifold
to compensate for abnormal enrichment of mixture in high idle
temperatures and to stabilize the engine. The idle compensator
Orifice
is installed on the air cleaner.
T o Intaka
manifow
EFW
B.C.D.D. (Boost Controlled Deceleration Device)

Control Valve
Bypass air
Vacuum chamber I I
Vacuum chamber I
Flon
control solenoid
SEFB72Ci
ENGINE AND EMISSION CONTROL PARTS DESCRIPTION lT8421
B.C.D.D. (Boost Controlled Deceleration Device)
Contrd Valve (Cont'd)
The B.C.D.D. control valve opens and closes the air by-pass
passage of the carburetor. When the throttle valve closes
abruptly during deceleration, intake manifold vacuum increases
abnormally. This causes engine oil to leak past the piston into
the combustion chamber and unburned gases inside the intake
manifold to be discharged into the atmosphere in the form of
HC. To prevent an abnormal rise in intake manifold pressure
and an abrupt decrease in engine speed during deceleration,
the air by-pass passage opens to deliver a very small amount of
fuel from the coasting jet when intake manifold vacuum pres-
sure reaches the specified level.
The B.C.D.D. control valve is installed on the intake manifold
carburetor.
B.C.D.D. Control Solenoid Valve

The B.C.D.D. control solenoid valve stops B.C.D.D. operation
when engine speed decreases to such an extent that the
vehicle stops. This prevents abrupt movement of the vehicle.
Fuel Cut Solenoid Valve

The fuel cut solenoid va1ve.i~attached to the carburetor with its
needle valve facing the fuel passage of the primary slow system.
When current flows through the fuel cut solenoid valve, the
needle valve retracts, allowing the current to flow through the
primary slow system. When current does not flow through this
solenoid valve system, the fuel will be shut off.
Fuel Pump
The fuel pump is a mechanical type and is mounted on the
cylinder block. The end of the pump lever rests on the oil pump.
When the cam rotates, the lever moves in a reciprocating
motion to deliver fuel from the fuel tank to the carburetor.
ENGINE AND EMISSION CONTROL PARTS DESCRIPTION Fz!l
7
Carbon Canister
Main purge
The carbon canister is filled with active charcoal to absorb
evaporative gases produced in the fuel tank. These absorbed
gases 'are then delivered to the intake manifold by manifold
vacuum for combustion purposes.
purge orifice 0 : Air

C m b n canister : Fuel vapor
SEFU3Qb
CARBURETOR IT&(21
Component .Parts
Model except Australia and Gulf standard models
Choke ~ ~ w n n u -
e,r L w
-3-6
(as.0.6,-
2.2 -4.3)
pump lever
Float
Accelerating pump piston
Secondary small venturi

Primary main air bleed
Primary small venturi
Boost controlled
Throttle lanr
CARBURETOR I-
Component Parts (Cont'd)
Australia MK model
(0) : N-rn (kg-rn, ft-lb)
SEF457G
CARBURETOR
Australia A D model
&ut~ahoka
wbimltd-
Acderatlng pump lever
Accelerating pump plston

Pr~marymain air bleed
Pr~marysmall venturl
Thmttle adjusting screw
-
10.5 0.9.3.6 - 6.5)
CARBURETOR ITB42 1
Gulf standard M/T model
[C))3-6t0.3-08.22-43
m 3-6
Choke chamber
(0.3 0.6, -
-
2.2 43)
punp lever
Fton
Accelerating pump piston
,-Secondary main air bleed
B.C.D.D. control solmoid
\ 8005t controlled
deceleration d m f i i l
Semdm
With air conditioner

mde4 only
Throttle adjusting screw
(0.5 - 09.3.6 - 661

CARBURETOR L!%l
Gulf standard A/T model
Secondary main air bl-
maln air bleed
W ~ t halr condnioner
model only
: N.m (kg-rn. ft-lb)

Main system Slow system
Slow economizer bleed
Bypass port
Float chamber
main jet
dda dde
adjusting screw
Step system Accelerating pump system Power valve system
ary main
d
Injector -, , n ~ P r i m a r vmain air bleed
Accelerating
pump piston
- 1I \ Llnlet check valve

-1
L o u t l e t check valve
Primary
side
CARBURETOR lI!!!El
Major Service Operation
The perfectly adjusted carburetor delivers the proper fuel and
air ratios at all speeds.
The carburetor should be maintained in its original condition in
order to continue to deliver the proper ratio.
To maintain accurate carbureting through passages and dis-
charge holes, extreme care must be taken in cleaning.
REMOVAL
Remove carburetor from engine, taking sufficient care to do the
following:
PRECAUTIONS:
a. When disconnecting fuel lines, do not spill fuel from fuel
pipe.
b. When removing carburetor, do not drop any nut or bolt
into intake manifold.
c. Be careful not to bend or scratch any part.
CLEANING AND INSPECTION

Dirt, gum, water or carbon in or on exterior moving parts of
carburetor can cause poor performance. Therefore, clean and
inspect carburetor carefully.
Before assembling and installing carburetor, blow the passages
and castings with compressed air, then blow all parts dry.
Do not pass drills or wires through calibrated jets or pas-
sages as this may enlarge orifice and seriously affect carbu-
retor calibration.
CARBURETOR - Inspection and Adjustment lfs421
Fuel Level
INSPECTION
Disconnect ignition wire between

distributor and coil.
1
~
I Disconnect fuel cut solenoid

connector of carburetor.
IB 1
Check primary main nozzle to
N.G.
ensure that no fuel is discharging
*
1
I while cranking engine for

approximately 3 seconds. I Check needle valve for looseness
or sticking. If necessary, repair
or replace.
Adjust fuel level.
Check that acceleration pump
. .
I
I
nozzle injects fuel when throttle
valve is opened.
1 O.K.
I
I
END
!
Primary
side
SEF548G
CARBURETOR - Inspection and Adjustment ml
Fuel Level (Cont'd)
ADJUSTMENT
1. Remove carburetor from engine.
2. Remove float chamber cover from float chamber.
3. Turn carburetor upside down, and fix it horizontally.
4. Raise float fully, then lower it slowly until float seat contacts
needle valve, and in this position, check height "HI".
- -
Height "H,": 9.5 10.5 mm (0.374 0.413 in)
If out of specification, adjust by bending float seat. Make sure
needle valve slides smoothly on the float seat.
SEFS37G
5. Lower float slowly until float stopper contacts carburetor,

and in this position, check height "H2".
- -
Height "H2": 47.5 48.5 mm (1.870 1.909 in)
If out of specification, adjust by bending float stopper.
SEF674G
If necessary, use Tool to visually check fuel level as follows:

Top aide 1. Disconnect inlet fuel hose from carburetor, and plug open-
ing.
2. Start engine and wait for it to stop.
3. Install Tool on carburetor, as shown.
Be careful not to spill fuel.
4. Connect inlet hose to carburetor.
5. Start engine. Visually check fuel level.
SE F453Q
CARBURETOR - Inspection and Adjustment lE!El
Automatic Choke
MECHANICAL CHECK
1. Before starting engine, fully open throttle valve and ensure
that choke valve closes properly.
2. Push choke valve with your finger to check for smooth
movement.
3. Make sure bimetal cover index mark is aligned with the

center of choke housing index mark.
4. Check wiring connection, and start engine.
5. After warming up engine, ensure that choke valve is fully
open.
If not, check automatic choke circuit and heater.
AUTOMATIC CHOKE HEATER

1. Disconnect carburetor harness connector.
2. Check for continuity between choke heater connector ter-
minal @ or @ and choke housing.
Continuity should exist.
AUTOMATIC CHOKE RELAY

Automatic choke relay is installed in the engine room.
Check relay for proper operation.
CARBURETOR - Inspection and Adjustment - = -- IT&(2l
Fast ldle (Automatic Choke Model)
1. Warm up engine. Set fast idle arm on 2nd step of fast idle
cam.
2. Check fast idle speed and if out of specification, adjust it by
turning fast idle adjusting screw.
Fast idle speed (at 2nd cam step):
-
M/T: 1,600 2,000 rpm
-
A n : 1,800 2,200 rprn
Make sure that the engine is completely adjusted (idle rpm,
ignition timing, etc.) before checking or adjusting fast idle
speed.
3. If out of specification, remove carburetor and make fast idle

adjustments as follows.
1) Place fast idle arm on 2nd step of fast idle cam, in the same
manner as in step 1 above.
2) Adjust clearance "A" between primary throttle valve and
inner carburetor wall by turning fast idle adjusting screw.
Clearance "A":
MA: 1.37 f 0.14 mm (0.0539 k 0.0055 in)
A/T: 1.64 f0.14 mm (0.0646 f0.0055 in)
If after adjustment and installation, the fast idle speed is out
of specification, check clearance "A" values.
Fast ldle (Manual Choke Model)

Check clearance "A" between primary throttle valve and inner
wall by pulling choke lever completely.
Clearance "A":
+
MA: 2.25 0.15 mm (0.0886 f0.0059 in)
+
A/T: 2.58 0.15 mm (0.1016 f 0.0059 in)
If out of specification, adjust it by bending choke connecting
rod.
CARBURETOR - Inspection and Adjustment -- lI!?!a
Fast Idle (Manual Choke Model) (Cont'd)
h
Connecting link bend to
~- - SEF037
Vacuum Break
1. With engine cold, visually check that choke valve is fully
closed.
2. Apply vacuum to vacuum break diaphragm with a handy
vacuum pump.
3. Lightly push piston rod in the direction that closes choke

valve and check clearance "R1".
Clearance "RI":
3.25 f0.25 mm (0.1280 f0.0098 in)
If out of specification, adjust "R1" by bending tongue.
4. Lightly push piston rod toward diaphragm and check clear-

ance "R2".
Clearance "R21':
5.0 f0.5 mm (0.197 f 0.020 in)
If out of specification, recheck and adjust clearance "R1".
- - --
- - - CARBURETOR - Inspection and Adjustment 1lB42 1
Accelerating Pump
Operate accelerating pump by opening throttle lever with engine
stopped. Check that pump nozzle located at primary port
injects fuel smoothly without delay.
If it does not inject, check accelerating pump piston or linkage.
- -
. - 1
Fuel Cut Solenoid Valve
Australia M/T 1. Connect solenoid valve connector to battery.
model 2. Check "click" sound from solenoid valve when battery is
connected and disconnected.
Gulf standard M/T model
Fud cut
Model excrpt Australia M/T and

Gulf standard M K models
SEF450G
3. If no sound is heard from fuel cut solenoid valve, replace

with a new one.
1) Disconnect harness from harness connector.
SEF482D
2) Remove fuel cut solenoid valve from carburetor.

3) Install new fuel cut solenoid valve.
After replacement, start engine and check that fuel cut
solenoid is in good condition.
CARBURETOR - Inspection and Adjustment (TBUI
F.I. (Fast Idle) Pot (A/T model only)
DASH POT '
1. Warm up engine sufficiently.

2. Check idle speed and mixture ratio.
ldle speed:
650f 5 0 rpm (MW
650f50 rprn (Am in "D" position)
ldle "COW:
1.5 fO.sO/O
3. Turn throttle valve by hand, and read engine speed when
dash pot just touches stopper lever.
Dash pot touch speed:
1,700 f 100 rprn
4. If out of specifications, adjust it by turning adjusting screw.
5. After adjusting, make sure that engine speed drops
smoothly from 2,000 to 1,000 rprn in approximately three
seconds.
F.I. Actuator
1. Warm up engine sufficiently.
2. Check idle speed and mixture ratio.
ldle speed:
650 f 50 rprn (M/T)
650 f 50 rpm (Am in "D" position)
ldle "COW:
1.S f0.5%
3. Turn air conditioner switch "ON", and check idle speed.
ldle speed (When A/C is "ON"):
1,100 f50 rprn (M/T)
900 f 50 rprn (Am in "N" position)
4. If out of specification, adjust idle speed by turning adjusting
screw.
CHECKING AND ADJUSTING IDLE SPEED,
IGNITION TIMING AND MIXTURE RATIO
CAUTION:
Do not attempt to screw idle adjusting screw down com-
pletely. Doing so could cause damage to tip, which in turn will
tend to cause malfunctions.
PREPARATION
1. Set shift lever in "Neutral" position (in "N" or "P" position
for the automatic transmission). Engage parking brake and
lock both front and rear wheels with wheel chocks.
2. Turn off air conditioner and light switch.
3. Use "COW-meter after it is fully warmed up, and insert
"COW-meter probe into tail pipe more than 0.4 m (1.3 ft).
4. Measure "CO"% with air cleaner installed.
5. During checking and adjusting, make sure that engine is at
normal operating temperature.
IGNITION TIMING AND MIXTURE RAT10 p q
( START 'I
Confirm that engine is at normal

operating temperature.
2
I
Race engine (2,000 - 3,000 rpm) 2 or 3
times under no-load, and then run engine
at idle weed for one minute.
'
Check idle speed.
M R : 650*50
SMA957A
N.G.
Adjust ~ d l espeed by tu
adlusring screw.
/ I I
,
tlmlng: B.T.O.C.
tgn~tlon
1O0*l0
O.K. N.G.
Adjust ignirlon trrnlng by turning

distributor.
-
Race engine (2,000 3,000 rpm) 2 or 3
times under ndoad, and then run
engine at idle speed.
4
- Adjun idle speed bv turning throttle
adjusting scrm.
-
Idle@: rpm
M K : 650i50
AIT: 65Ot50
(in "D" position)
7
-
Race engine (2,000 3,000 rpm) 2 or 3
times under no-load, and then run engine
1-
at idle speed for one minute.
1
Idle weed.
Conf ~ r m
IdleM
sped: rpm
R : 650+50 N.G.
AlT: 66m50
(In " D ori it ion)
O.K. I
IGNITION TIMING AND MIXTURE RATIO
-
pI
With "C0"-meter
Check "CO"% at idle speed.

ldle "CO": %
154.5
Adjust idle "CO"% by turning idle

adjusting screw.
END I
v-- LL
CAUTION:
Do not attempt t o screw the idle
--
-.- -* adjusting screw down completely.
Turn out idle adjusting screw appoxi- Doing so could ause d a m e t o
rnately two turns. starting from fully tip, which in turn will tend to
closed position.
causa malf unctions.
- 4
SEF441G
1
Adjust engine speed by turning throttle . ..- - -
adjusting screw.
7:--
7. ,
Engine s p e d : rpm
M/T: 650t50
m: 650250 (in "D" position)
. .
.
SE FdO2G
Turn idle adjusting screw clockwise

one full turn.
4
Adjun ~ d l espPed by turning rhroltle
adjusting screw.
Idle speed: rpm

MR: 650250
A n : 650250 (in "D" position) SE FddZG
END 3
ALTITUDE COMPENSATION SYSTEM DESCRIPTION
Altitude compensator
Carburetor
SEF326
System Description
The higher the altitude, the thinner the density of air. At a higher
altitude, therefore, the carburetor produces too rich of an
air-fuel mixture.
The altitude compensator automatically corrects air-fuel mixture
to an optimum ratio. It operates in the following sequence in
high altitudes.
1. The bellows in the altitude compensator extend.
2. The lever attached to the bellows then pushes up the needle.
3. When the needle is pushed up, the air passage becomes
wider, allowing a larger amount of air to flow from the
altitude compensator to the carburetor.
4. With this additional air in the carburetor, the air-fuel mixture
thins to a proper ratio.
r - - - - -- - - --
-- 7 Front
P- -
\\
/I
/
'-From air cleaner

Carburetor -
\TO carburetor
'-Altitude COmpenStOr
SEF444G
ALTITUDE COMPENSATION SYSTEM INSPECTION
System Inspection
a. The altitude compensator is set to operate above an
altitude of approximately 500 m (1,641 ft). It should be
carefully checked.
b. When making this check, ensure that all other parts are
working properly.
c. The altitude compensator cannot be adjusted; if it is found
to be functioning unsatisfactorily, it must be replaced as
an assembly.
d. The hose< are color-coded. When connecting them, be
sure to align them with the proper color marks on the unit.
COMPENSATOR AT LOW ALTITUDES

If compensator operates at low altitudes:
When compensator is malfunctioning, check it by sucking or
blowing air through the inlet and outlet hoses. If air flows
through smoothly, replace the unit as an assembly.
COMPENSATOR AT HIGH ALTITUDES

If compensator does not operate at high altitudes:
When compensator is malfunctioning, check it by sucking or
blowing air through the inlet and outlet hoses. If air does not
flow through smoothly, replace t h e unit as an assembly.
THROTTLE VALVE POSITION DETECTING SYSTEM INSPECTION
(Only for control of automatic transmission) pq
Wiring Diagram
Refer to "AT" section.
Inspection
THROlTLE VALVE SWITCH
1. Check engine speed during idle switch OFF + ON conver-
sion.
1) Warm up engine sufficiently.
2) Disconnect throttle valve switch and throttle sensor harness
connector.
3) Check idle speed.
650f 50 rpm (in "D" position)
If not correct, adjust by turning throttle adjusting screw.
4) Shift select lever to "N" position, then read idle speed Nat.
5) Manually open throttle valve to about 2,000 rprn, lower
engine speed slowly and read the engine speed at which the
idle contact turns from OFF to ON.
(Nat + 250) f 150 rpm (in "N" position)
If not correct, adjust by loosening throttle valve switch
securing screws and turning throttle valve switch.
6) Reconnect throttle valve switch and throttle sensor harness
connector.
2. Check continuity of throttle valve switch.

1) Disconnect throttle valve switch harness connector.
2) Check resistance between terminals @ and @ when
throttle valve switch closes fully.
Resistance:
Approximately OR
3) Check resistance between terminals @ and @ when
throttle valve switch opens fully.
Resistance:
Approximately 0R
If necessary, replace throttle valve switch.
THROlTLE VALVE SENSOR

Check resistance of throttle valve sensor.
1) Disconnect throttle valve sensor harness connector.
2) Check resistance between @ and @ changes when open-
ing throttle valve manually.
Resistance should change.
If not, replace throttle valve sensor. Check engine speed
during idle switch OFF + ON conversion.
MECHANICAL FUEL PUMP INSPECTION - -- bEl
Operation
1. Flush pump by immersing it in a fuel bath and operating the
rocker arm several times.
2. Drain fuel from fuel pump. Then plug up inlet port with
fingers and check that pump arm does not move.
3. Remove finger from inlet port and listen for a suction sound
which will confirm that sufficient suction was produced.
4. Plug up outlet port and return port. Once again operate

rocker arm. After air pressure has been built up, confirm
that the pressure remains for two or three seconds after.
5. Put a finger over the outlet port and again build up pressure
in the pump. Then submerse pump in a fuel bath and check
for air leaks.
WARNING:
.Before starting to work on any part of fuel system, disconnect
ground cable from battery. When disconnecting fuel hoses,
use a container to catch fuel remaining in the hoses.
Fuel Pressure
1. Disconnect fuel return hose and plug with a suitable blind
plug.
2. Disconnect fuel feed outlet hose and connect fuel pressure
gauge between fuel pump and carburetor.
3. Check static fuel pressure with engine running at various
speeds.
Fuel pump static pressure:
- -
25.5 32.4 kPa (0.255 0.324 bar,
- -
0.26 0.33 kg/cm2, 3.7 4.7 psi)
If out of specification, check for fuel filter clogging or
improper fuel pump operation.
EXHAUST GAS RECIRCULATION (E.G.R.) CONTROL SYSTEM
System Description
The exhaust gas recirculating system is provided as a means of
emission control. It routes a portion of the exhaust gas into the
intake manifold for recombustion, thereby reducing the NOx
level. The amount of exhaust gas recirculated depends on the
port vacuum which operates the E.G.R. control valve.
1. During idling
No port vacuum is generated because of low exhaust gas
pressure. The vacuum port located upstream of the throttle
valve and the E.G.R. valve remains closed.
2. Exhaust gas pressure is less than the pressure of E.G.R.
control valve return spring.
The throttle valve begins to open, generating port vacuum.
Hence, the E.G.R. control valve opens.
3. Exhaust gas pressure greater than E.G.R. control valve
return spring.
If the throttle valve opens further, the port vacuum weakens
and the E.G.R. control valve begins to close.
4. With throttle valve fully open
Thermal vacuum valve
Exhaust gas from When the throttle valve opens fully, no port vacuum exists
exhaust manifold
and the E.G.R. valve closes.
In addition to the above, a T.V.V. (Thermal Vacuum Valve) is
SEC703 installed in the E.G.R. control vacuum line. This valve closes the
vacuum port at low temperatures, thereby keeping the E.G.R.
control valve closed.
System Inspection
E.G.R. CONTROL VALVE
1. Supply the E.G.R. control valve with vacuum using a handy
vacuum pump.
2. Place a finger on the diaphragm of the valve, and make sure
that the diaphragm lifts up and down in response to the
vacuum leading to the valve.
Full open of E.G.R. valve:
Over -14.7 kPa
(-147 mbar, -110 mmHg, -4.33 inHg)
T.V.V. (Thermal Vacuum Valve)

Apply vacuum to thermal vacuum valve and ensure that thermal
vacuum valve opens at a temperature of about 50°C (122OF)
conducting vacuum passage.
Do not let water enter thermal vacuum valve.
Be sure to apply sealer to threads of the valve prior to
installing new valve.
(nl : Thermal vacuum valve
- - -
18 22 N-m (1.8 2.2 kg-m, 13 16 ft-lb)
EVAPORATIVE EMISSION CONTROL SYSTEM DESCRIPTION
System Chart
I Throttle chamber
I
Fuel filler cap with

vacuum relief mlve \constant
, purge orif ice
Fuel mnk
0 : Air
: Fuel vapor
1 - - - -. SEC544A
System Description
The evaporative emission control system is used to reduce
hydrocarbons emitted to the atmosphere from the fuel system.
This reduction of hydrocarbons is accomplished by activated
charcoals in the carbon canister.
The fuel vapor from the sealed fuel tank is led into the canister
which contains activated carbon, and the vapor is stored there
when the engine is not running.
The canister retains the fuel vapor until the canister is purged
by the air drawn through the bottom of the canister to the
intake manifold when the engine is running. When the engine
runs at idle, the purge control valve is closed.
Only a small amount of stored vapor flows into the intake
manifold through the constant purge orifice. As the engine
speed increases and the throttle vacuum rises higher, the purge
control valve opens and the vapor is sucked into the intake
manifold through both the main purge orifice and the constant
purge orifice.
EVAPORATIVE EMISSION CONTROL SYSTEM INSPECTION I TB42 I
Carbon Canister
Check carbon canister as follows.
@ : Blow air and ensure that there is no leakage.
@ : Blow air and ensure that there is leakage.
-- .- - -- - -
.- .
Fuel Check Valve
1. Blow air through connector on fuel tank side.
side A considerable resistance should be felt, and a portion of air
f flow should be directed toward the canister.
2. Blow air through connector on the canister side.
Air flow should be smoothly directed toward fuel tank.
3. If fuel check valve is suspected of not properly functioning
in steps 1 and 2 above, replace it.
CI : Evaporative fuel flow
: Fresh air flow
ECOQOA
Fuel Tank Vacuum Relief Valve

1. Wipe clean valve housing.
2. Inhale air through fuel filler cap. A slight resistance accom-
panied by valve clicks indicates that valve is in good
mechanical condition. Note also that, by further inhaling air,
the resistance should disappear with valve clicks.
3. If valve is clogged or if no resistance is felt, replace cap as
an assembly.
POSITIVE CRANKCASE EMISSION CONTROL SYSTEM DESCRIPTION
System Description
Intake manifold
P.C.V. valve
Fresh air
Blcw-by gas
The positive crankcase ventilation (P.C.V.) valve provides

Englne nor runnlng
or b a c k f ~ r ~ n g
Cruising crankcase blow-by gas to the intake manifold.
1
I
I Idling or
decelerar~ng
Acmlerat~on
or hioh load
System Inspection
Refer to MA section.
POSITIVE CRANKCASE EMISSION CONTROL SYSTEM INSPECTION
P.C.V. (Positive Crankcase Ventilation) Valve

With engine running at idle, remove ventilation hose from P.C.V.
valve; if valve is working properly a hissing noise will be heard
as air passes through it, and a strong vacuum should be felt
immediately when a finger is placed over valve inlet.
Ventilation Hose
1. Check hoses and hose connections for leaks.
2. Disconnect all hoses and clean with compressed air. If any
hose cannot be freed of obstructions, replace.
AUTOMATIC TEMPERATURE CONTROL (A.T.C.) AIR CLEANER SYSTEM
Engine: Cool condition System Description

The automatic temperature control system maintains the tem-
perature of air sucked in the carburetor within the constant
range, thereby enabling lean setting for carburetor calibration. In
addition to this, the automatic temperature control system is
effective to improve the warm-up characteristics of the engine
and to prevent carburetor from icing.
- SEC5SlA
Engkw: Hot condition -

-
The automatic temperature control system is controlled by the
inlet air temperature and the load condition of the engine. The
inlet air temperature is detected by the sensor, installed in the
air cleaner, and the vacuum motor is actuated by the intake
manifold vacuum.
When the engine is not warmed up sufficiently, since the A.T.C.
temperature sensor passes the intake manifold vacuum to the
vacuum motor, the motor actuates and hot air is introduced into
the air cleaner. In this step, the higher the intake manifold
vacuum is, the wider the air control valve opens.
SEC552A When the engine is warmed up, the A.T.C. temperature sensor
i
- -
releases to the atmosphere the intake manifold vacuum leading
to the vacuum motor. Therefore, the vacuum motor deactivates.
In this step, the air control valve shuts off hot air, allowing
normal temperature air to flow to the air cleaner.
System Inspection
a Engine stall or hesitation
a Increase in fuel consumption
Lack of power
If these phenomena occur, check A.T.C. system before carrying
out inspection of carburetor.
1. Check hoses for cracks, distortion and improper position.
2. Check A.T.C. system for proper function while engine is cool.
Check air control valve position.
Air control valve is correct if it is in lower position.
3. Start engine and immediately check air control valve position.

If it rises, it is correct.
4. Make sure that air control valve moves up and down when
engine speed is quickly increased and decreased.
5. Make sure that air control valve partially rises when engine
warm-up advances.
If the above test reveals any problem in the operation of air
control valve, carry out the following test:
AUTOMATIC TEMPERATURE CONTROL (A.T.C.1 AIR CLEANER SYSTEM
Vacuum Motor
Disconnect inlet vacuum hose of vacuum motor, and connect
another hose to the inlet to apply vacuum to vacuum motor.
Then, confirm that air control valve moves.
Air control valve operating vacuum:
kPa (mbar, mmHg, inHg)
Opening starts
-9.6 (-96, -72, -2.83)
Full opening
Over -19.5 (-195, -146, 3.75)
Temperature Sensor
While engine is cool and idling, disconnect inlet vacuum hose of
vacuum motor and make sure that intake manifold vacuum is
present at the end of the vacuum hose. If vacuum is weak or is
nonexistent, check vacuum hose for leakage.
Replace temperature sensor if vacuum hoses are in good
condition. After engine warms up, make sure no vacuum exists.
If necessary, replace temperature sensor.
ldle Compensator Inspection

1. Remove air cleaner.
2. Suck on the hose to make sure that idle compensator does
not open.
3. Direct warm air to idle compensator with a heat gun.

And measure operating temperature of idle compensator.
Place thermometer as close as possible to idle compen-
sator sensor.
4. ldle compensator is in good condition if air flow opens idle
compensator when it reaches operating temperature.
Take care not to bend or damage bimetals of idle
compensator.
Above 74 ( 165)
ANTI-AFTERBURNING CONTROL SYSTEM INSPECTION E l
Boost Controlled Deceleration Device (B.C.D.D.)
Overall Inspection
1. Disconnect B.C.D.D. control solenoid connector.
This is necessary for Australia M K and Gulf standard M K
models. For other models, perform inspection and adjust-
ment from item 2.
2. Fully loosen dash pot adjusting screw, if equipped.

After inspection and adjustment have been made, readjust
dash pot touch speed. Refer to EF 81 EC section.
3. Connect vacuum gauge to intake manifold.
4. Start engine and observe vacuum gauge while racing engine.

a: Maximum negative pressure 5. If B.C.D.D. is .in good condition, vacuum gauge will follow
the pattern shown in the figure at left.
Set pressure are shown in item 6.
Tima
Characteristic curve of B.C.D.D.
ECSO2
6. If it does not react as described above, adjust operating

pressure.
1) Remove rubber cap on B.C.D.D.
2) Racing engine, turn adjusting screw until the specified set
pressure is obtained.
B.C.D.D. set pressure (at sea level):
For Australia M K and Gulf standard M K models
-76.0 f0.7 kPa (-760 f 7 mbar,
-570 f5 mmHg, -22.44 f0.20 inHg)
For model except Australia M K and Gulf standard
MIT models
-78.6 f 0.7 kPa (-786 f 7 mbar,
-590 f5 mmHg, -23.23 f0.20 inHg)
ANTI-AFTERBURNING CONTROL SYSTEM INSPECTION ITs42)
Boost Controlled Deceleration Device (B.C.D.D.)
Adjust~ngscrew Overall Inspection (Cont'd)
IB
Rubbr a. Turning adjusting screw one-quarter rotation will cause a
change in operation pressure of about 2.7 kPa (27 mbar, 20
rnmHg, 0.79 inHg).
b. Do not fit tip of screwdriver tightly into screw slot.
Turn clockwise to reduce operating pressure.

Turn counterclockwise to Increase operating
pressure.
ET037
Circuit Check
1. Disconnect carburetor harness connector.
2. Turn ignition switch "ON" and check voltage between
terminals of B.C.D.D. control solenoid valve at main harness
side connector.
Battery voltage should exist.
3. Jack up the rear of the vehicle, support with safety stands,

block front wheels, and set parking brake.
4. Start engine and drive rear wheels until speedometer indi-
cates 20 kmlh (12 MPH) by putting transmission in 1st gear
and depressing accelerator pedal.
WARNING:
For safety, do not drive rear wheels, at higher speeds than
necessity.
5. Disengage clutch and slowly decelerate without braking.

6. Ensure that voltmeter indicates as follows:
Below 10 kmlh (6 MPH): Battery voltage
Above 10 kmlh (6 MPH): 0 M
If out of specification, check harness continuity between
B.C.D.D. control solenoid valve and ignition switch.
SE F482G
B.C:D.D. Control Solenoid Valve

Check function of B.C.D.D. control solenoid valve after discon-
necting its connector. Listen for clicking sound of solenoid valve,
applying battery voltage to solenoid valve.
IGNITION CONTROL SYSTEM INSPECTION p q
Wiring Diagram
(1SM) IGNITION 1
SW I T C H
BATTERY
W/B
FUS I B L E
LINK
@@
(Mai n h a r n e s s )
"="' '@.AA model for Gul f standard (Middle east)

SPARK
@ : ~ x c e p t A/T model for Gulf standard (Middle east)
SEF650G
IGNITION CONTROL SYSTEM INSPECTION __
Trouble-shootlng
I
N.G.
ek&k wition timing.
0 Engine turns but does not start.
Before cranking, disconnect harness
+ +
Attach adapter * 1 t o high tension
, connector to carburetor. Before
operation, make sure there is no in-
flammable.
Adjust. cable and position tip of adapter
approx. 6 mm (0.24 in) away
O.K. from cylinder block. With adapter
held in that position, crank engine
to see i f spark jumps across gaps
between tip and cylinder block at
regular intervals.
4 N.G.
<
I
Mrnm nrLtlnca of rh high
m i o n &lo.
<
>
Check for signs of dirt or burning
Check for burned or fouled rpark plug.
on distributor cap, rotor head,
I
point, etc.
Chrk Ignition d l .
Test lamp lights when points open.

... Replace condenser.
3 O.K. Test lamp goes out when points
.
WARNING:
.
Chakfml system.
-- --
close.
... Check lead wires @and @) for
open circuit. I f necessarv. reolace.
When current is flowing, never
touch with bare hand high tension
cables or any other parts with high
voltage. I f parts are moist, touching
them could tause.anelectric hock,
even if they are insulated. Always
wear dry, well-insulated gloves or Test lamp goes out when points open.
wrap affected parts with dry doth ...O.K.
T e n lamp lights when points close.
before handling.
...O.K.
-1:
R.p.rat.tionof m r k plug for chocking
Many things can be utilized as an
adapter. However, it is recommended
that a used spark plug whose thread-
ed portion has been half cut off as
mown in the figure be utilized.
IGNITION CONTROL SYSTEM INSPECTION - -
- .
ITB021
Trouble-shooting (Cont'd)
0 Engine knocks persistently or does

not develop sufficient power.
Cluck *Qnitiontiming. Adjwt.
on distributor cap, rotor head, Cl-n or replace.

point, etc.
4 O.K.
Check for dislocation or breakage
of governor spring. Also check
governor for malfunctioning.
0.K.
Check for signs of dirt or burning
on spark plug. C h n or mi-.
O.K.
Qnck fwl system d air intake
lynem.
IGNITION CONTROL SYSTEM INSPECTION I~ B 4 12
Construction
@) : H~gh-temperaturegrease points
SEFW(3
- -.>
IGNITION CONTROL SYSTEM INSPECTION [-mi
Distributor.Component Check
CAP AND -ROTOR HEAD
1. Check the cap and rotor head for dust, carbon deposits and
cracks.
2. Measure insulation resistance between electrodes on igni-
tion coil and spark plug sides on the cap.
Insulation resistance:
More than 50 [Ma]
Less than specified value ... Replace.
CONTACT POINT
1. Check the point surface.
Take off any irregularities with fine sandpaper (No. 500 or
600) or with oil stone.
2. Adjust point gap.
Loosen breaker point set screw and adjust gap with a gap
gauge.
Point gap:
- -
0.45 0.55 mm (0.018 0.022 in)
DWELL ANGLE
kT
Wide point a p 1. Start engine and warm it up.
2. Run engine at idle speed and measure dwell angle with a
dwell meter.
-
Dwell angle: 34O 40°
3. If dwell angle is not within the specified value, turn off
engine and adjust point gap.
Small dwell 4. If dwell angle is not within the specified value when point
gap is correct, cam lobe is worn. Replace cam.
The wider point gap, the smaller
$well angle.
smell point amp
k dwell
The4narrower
~ point
angle. d gap,
w thel larger
l I:
-..
. . SM-74 ,.
VACUUM ADVANCE
1. Connect vacuum pump gauge to vacuum controller and
gradually draw a vacuum while watching breaker . plate
movement. Check for smooth operation with no evidence of
binding.
2. Turn breaker plate right and left to check for freedom of
movement.
IGNITION CONTROL SYSTEM INSPECTION E!!El
Distributor Component Check (Cont'd)
GOVERNOR ADVANCE
Turn the head of cam assembly counterclockwise, release it,
then check that it returns smoothly to the original position.
ROTOR
Check that the plate moves smoothly to contact the metal
piece. Also check that the spring acts securely.
DISASSEMBLY
Carefully observe the following instructions during disassembly.
Put a matchmark across cam and shaft so that original
combination can be restored at assembly.
Inscribe a matchmark across spring and mating parts so
that spring can be replaced in its original position during
assembly.
Be careful not to stretch or deform governor spring.
ASSEMBLY
Carefully observe the following instructions.
Grease point
Apply high-temperature grease to:
Governor spring
Frictional surface of governor weight
Frictional surface of breaker plate
Vacuum control shaft
Cam and cam head
Installation of governor
Gwen
spring
Install governor springs, governor weights and cam assembly to
drive shaft as shown in the figure.
ight pin
Cam
IGNITION CONTROL SYSTEM INSPECTION J TB42 1
Ignition Coil
1. Measure secondary resistance of ignition coil.
Resistance: Refer to S.D.S.
2. Measure primary resistance of ignition coil.

Resistance: Refer to S.D.S.
Spark Plug
Clean and check spark plug gap.
lgnition Wire
Check ignition wires.
INJECTION SYSTEM
CAUTION:
Disassembly and assembly of the injection pumps should
be done only in service shops authorized by NISSAN or by
the pump manufacturer.
The pump tester is required for servicing the pump.
Before removing fuel injection pump from vehicle, check
closely to make sure that it is definitely malfunctioning.
Fuel System
IN-LINE TYPE INJECTION PUMP
(Including rrdimmicrr)
P d w lf l h
SEF6370 ,
INJECTION SYSTEM LP!!zl
Fuel System (Cont'd)
VE-TYPE INJECTION PUMP
IN-LINE TYPE INJECTION PUMP E?!El
Removal
1. Remove injection tube.
Cover the delivery holders of the injection pump and injection
nozzle holder assembly with a clean rag to prevent dust entry.
2. Disconnect governor hoses, fuel hoses and engine control
wire from injection pump assembly and oil feed pipe (if so
equipped).
3. Remove timing gear cover.
4. Remove timer round n u t

5. Remove timer assembly.
6. Remove injection pump assembly.
I
Installation and Adjustment
1. Install injection pump assembly with new gasket temporarily.
2. Install timer assembly.
Align crank pulley and timing gear case cover marks so that No. 1
piston is at top dead center.
IN-LINE TYPE INJECTION PUMP ITDlZ]
Installation and Adjustment (Cont'd)
3. Injection pump
( 1 ) Temporarily set injection pump.
(2) Mesh injection pump drive gear with idler gear a t "Z" mark
and then align gear to key way of injection pump camshaft
while turning crank pulley.
Coat key with grease to prevent it from falling into front cover,
and lay a rag on front cover.
(3) Secure timer assembly with lock washer and round nut.
INJECTION TIMING ADJUSTMENT

1. Turn crank pulley in standard rotating direction and set
No. 1 piston a t applicable B.T.D.C.
Select the right mark as applicable B.T.D.C.
2. Remove all injection tubes and governor hoses.
3. Remove No. 1 lock plate and delivery valve holder, and then
pull out delivery stopper (if so equipped), delivery valve
spring and delivery valve.
4. Install delivery valve holder without delivery valve spring,

delivery valve stopper and delivery valve.
---
. - IN-LINE TYPE INJECTION PUMP , - lmrZl
5. Connect test tube to the No. 1 delivery valve holder.
6. Push injection pump assembly fully down toward engine
side.
While feeding fuel by operating priming pump, slowly move

injection pump until fuel flow from No. 1 injection tube
stops.
Fix injection pump in the position where fuel flow stops.
Check whether or not the injection timing marks of injection

pump and front plate are aligned. I f not aligned, stamp a new
mark on front plate.
10. Remove No. 1 test tube and delivery valve holder.

11. Install delivery valve spring, delivery valve stopper, delivery
valve holder and delivery valve.
12. Install injection tubes, new timing cover gasket and timer
cover.
Coat sealant with new timing cover gasket.
13. Connect governor hoses, fuel hoses and engine control wire.
14. Bleed air. Refer to Bleeding Fuel System.
IDLE AND MAXIMUM SPEED ADJUSTMENT

CAUTION:
a. Do not remove sealing wires unless absolutely necessary.
b. Maximum speed adjusting screw is retained by sealing wire
and need not be adjusted under normal circumstances. How-
ever, if it should become necessary, adjust it with the screw.
After adjustment, always wind up with sealing wire.
IN-LINE TYPE INJECTION PUMP 11042 1
Throttle control wire adjustment
1. Make sure that free play is 1 mm (0.04 in) a t venturi's throt-
tle lever.
2. I f not within the specified range, adjust with wire adjusting
nut.
3. After adjusting free play properly, tighten lock nut.
Idle adjustment
Refer to section MA for idle adjustment.
Maximum speed adjustment

Maximum speed adjustment screw is retained by sealing wire
and need not be adjusted under normal circumstances. However,
if it should become necessary to adjust it, the following p r e
cedures should be followed:
1. Start engine and warm it up until coolant temperature indi-
cator points to middle of gauge.
2. Connect tachometer's pick-up to No. 1 fuel injection tube.
To obtain accurate reading of engine rpm, loosen clamp that
secures No. 1 fuel injection tubes.
3. To obtain maximum speed, turn the adjusting screw either
direction while fully depressing accelerator pedal.
Maximum engine speed
(Under no-load):
4.60Q 100 rpm
4. After adjustment, tighten lock nut securely.
5. Wind up with a sealing wire.
Altitude Compensator (Engine on vehicle)

REMOVAL AND INSTALLATION
1. Remove altitude compensator from bracket.
2. Disconnect vacuum hose and remove bracket from injection
pump.
3. Install altitude compensator in the reverse order of removal.
INSPECTION
1. Check for loose connections.
2. Check for altitude compensator movement.
If it does not move, contact a service shop authorized by the
pump manufacturer.
-- IN-LINE TYPE INJECTION PUMP ls!2l
(Cont'd)
ADJUSTMENT
This adjustment should be performed with injection lwer in
free position.
1. Loosen lock nut and cap nut of altitude compensator.
2. Turn cap nut touch with injection lever and temporary

tighten lock nut.
3. Determining position of cap nut

( 1) Precise method
a. Using a barometer, measure atmospheric pressure in areas
where vehicles are to be operated.
b. Determine how much the cap nut should be loosened by
using the equation below.
R = 9.878 x x (760 - P)
where
R: Amount of loosening of cap nut (No. of revolutions
of cap nut)
P: Measured atmospheric pressure (mmHg)
Reference table
I
101.3
Atmospheric pressure P
(1,013,
kPa (mbar. mmHg. inHg)
760, 29.92,
Amount of loosening of cap nut

(No. of revolutions of cap
-. IN-LINE TYPE INJECTION PUMP :=- -- k 4
(Cont'd)
(2) Expedient method
Determine how much the .cap nut should be loosened, ac-
cording to altitude above sea level.
0 120 700 1,300 2.000 2,700 3,400

Approximate altitude m (ft)
(0) (394) (2,297) (4,265) (6,562) (8,859) (11,155)
Amount of loosening of cap nut

(No. of revolutionsof cap nut)
0 0.1 - 0.3 0.4 - 0.8 0.9 - 1.3 1.4 - 1.8 1.9 - 2.3 2.4 - 2.6
4. Mark cap nut indicating the number of times cap nut should
be rotated according to altitudes in which vehicles are to be
operated.
5. Tighten lock nut.
Ensure that bolt comes into contact with injection pump lever.
If it does not, loosen the bolt and readjust
Disassembly
Delivery valve holder
(qJ 29 - 34 N-m (3.0- 3.5 kgm, 22 - 25 ft-lb
-Lock plate
Stopper
Delivery valve spring-
Gasket 0-
Delivery valve-
Pump h w r l n ~
Control rack-.
Cenorrtrmringl
Control sleeve
Upper spring seat
Plunger spring//
,
'
Lower spring seat --/
IN-LINE TYPE INJECTION PUMP lTD42 I
Disassembly ( Cont'd)
PREPARATION
Before performing disassembly and adjustment, test fuel
injection pump and note test results except when testing is
impossible.
Prior to beginning to disassemble fuel injection pump, clean
all dust and dirt from its exterior.
Clean work bench completely, removing all foreign matter.
Collect only those service tools necessary for disassembling
and reassembling.
Be careful not to bend or scratch any parts.
Be careful not to mix parts of different cylinders.
Special tools for disassembling and reassembling fuel injection pump
I I 1. Drain injection pump oil.

2. Attach injection pump with Tool.
3. Remove feed pump and cover plate.

4. Check backlash between control rack and control pinion.
Refer to Inspection.
-- -
Disassembly (Cont'd)
5.
(1) Temporarily install timer to injection pump.
(2) Turn timer until tappet is raised to T.D.C. for each cylinder
and then install Tool between tappet adjusting bolt and nut.
If Tool cannot be installed, loosen tappet adjusting bolt.
6. Check camshaft end play.
7. Remove mechanical governor cover, diaphragm cover, dia-
phragm, flyweight and governor housing.
Refer to Governor for removal.
8. Remove plug.
9. Draw out camshaft.
10. Remove Tool DK57931210 by pushing tappet with Tool

DK57921012.
CAUTION:
Be careful not to damage housing plug hole threads.
11. Withdraw tappet assembly with Tool DK57931612 from

camshaft chamber by loosening Tool DK57921012.
- - IN-LINE TYPE INJECTION PUMP lz?%l
12. Remove plungers together with lower spring seat with Tool.
CAUTION:
Lay out plunger and plunger barrel in order in a pan of kerosene
or solvent Do not touch plunger with hand.
13. Remove plunger spring, upper spring seat and control sleeve
assembly.
When disassembling control sleeve assembly, put matching mark.
14. Remove lock plate.

15. Remove delivery valve holder and then remove delivery
holder spring, and delivery valve stopper.
16. Remove delivery valve by threading in Tool.
17. Remove plunger barrel by pushing it from below.

IN-LINE TYPE INJECTION PUMP lE!?zl
18. Remove cap and bolt and-nut on control rack.
19. Remove control rack guide screw and then draw out con-
trol rack.
lnspection
PUMP HOUSING
1. . Inspect for damage, cracks, etc.
If excessively damaged, replace it with a new housing.
2. Check plunger barrel drum surface for proper contact with
plunger barrel seating hole. Also, check for damage or cracks.
If faulty, replace with a new plunger and plunger barrel.
3. Measure tappet to housing clearance. If worn beyond wear
limit, replace tappet or housing.
Tappet to housing clearance (A-B) :
Limit
0.2 mrn (0.008 in)
CAMSHAFT
1. Measure cam profile for uneven or excessive wear. I f exces-
sively or unevenly worn, replace camshaft with a new one.
2. Check for damage, cracks, etc.
If excessively damaged, replace it with a new one.
3. Measure camshaft end play by pushing camshaft from timer
end so as t o move camshaft in shaft direction.
Camshaft end play:
Standard
-
0 - 0.02 mm (0 0.0008 in)
Limit
0.1.mm (0.004 in)
If camshaft end play is over limit, adjust as follows:
(1) Remove bearing inner race from camshaft.
(2)Based upon end play measurement, increase or decrease
adjusting shims.
Use t h e same shim thickness on each end.
(3) Re-install bearing inner race on camshaft.
---
--
- - - IN-LINE TYPE INJECTION PUMP B
Inspection-(Cont'd)
BEARINGS
Check for wear or discoloration. If faulty, replace with a new
one.
PLUNGER AND PLUNGER BARREL

The operation of the plunger should be checked based on the
results of fuel injection volume measurement
OIL-TIGHTNESS CHECK
1. Thoroughly clean piunger barrel in clear kerosene or solvent.
2. Tilt it to approximately 60". ,Then, let plunger slide down
through barrel, making sure that plunger slides smoothly.
Repeat this procedure by turning plunger t o various posi-
tions, making sure that plunger slides smoothly in any of
the positions.
When replacement is required, replace both the plunger and
plunger barrel as a set.
DELIVERY VA-LVE
Air-tightness check
1. Thoroughly clean delivery valve and delivery valve seat in
clear kerosene or solvent.
2. Place finger over lower part of valve seat, lightly depress
delivery valve with your finger tip, and make sure that valve
springs back when released. If valve falls to valve seat, it is
not operating properly due to excessive piston wear. If
faulty, replace with a new valve and valve seat assembly.
TAPPET
Inspect tappet, roller, roller bushing, and pin for wear or dam-
age. If faulty, replace with new components, as required.
Adjusting bolt head recess wear limit:
0 2 0 mm (0.0079 in).
Roller end play limit:
0 2 0 mm (0.0079 in)
CONTROL RACK AND CONTROL SLEEVE ASSEMBLY

1. Inspect control rack for bending and damage.
If faulty, repair or replace with a new control rack, as r e
quired.
2. Measure control sleeve to plunger lug clearance. If worn
excessively, replace control sleeve or plunger, as required.
Control sleeve to plunger lug clearance (A-B):
Limit
0.12 mm (0.0047 in)
Inspection (Cont'd)
3. Measure backlash between control rack and control pinion.
Backlash between control rack and control pinion:
Limit
0.30 mm (0.0118 in)
SPR lNG
Inspect plunger and delivery valve springs for damage and square-
ness.
Assembly
Clean parts thoroughly and apply a thin coat of engine oil to
rotating and sliding parts.
Assemble injection pump in the reverse order of disassembly.
Note the following items.
1. Set plunger barrel in position, with hole in barrel aligned with
dowel pin of housing.
2. Install delivery valve with new gasket on the plunger barrel.
3. Install delivery valve spring delivery valve stopper (if so

equipped) and delivery valve holder.
4. Install lock plates.

5.
(1) Set the control rack so that marks on both sides are same
distance "A" from each end of pump housing.
(2) Adjust bolt length and tighten lock nut.
(3) Then install control rack guide screw.
IN-LINE TYPE INJECTION PUMP - LTD421
Assembly [Cont'd)
6. Install control sleeve assembly with gap of control sleeve
facing straight up. Then install upper spring seats and plunger
springs.
7. lnstall plunger together with lower spring seat by using Tool

with plunger alignment mark facing upward (cover side of
pump housing).
Do not use plunger with a barrel from a different cylinder.
8. Install tappet assembly by reversing the removal procedure.
9. Install camshaft so that i t s alignment mark is toward

governor.
10. lnstall governor housing and then adjust camshaft end play.
11. Install screw plug on bottom of pump housing.
Seal the plug with sealant.
f l : Screw plug
54 - 74 N-m
(5.5 - 7.5 kg-m, 40 - 54 ft-lb)
12. Temporarily install timer and remove Tool DK57931210
while turning timer.
13. Measure control rack sliding resistance.
Control rack sliding resistance:
Less than 1.471 N (150 g, 5.29 oz)
14. Install flyweight, diaphragm, diaphragm cover and mechani-
cal governor cover in that order.
Refer to Governor for installation.
15. lnstall control rack cap, cover and feed pump.
Governor
DISASSEMBLY
Control lever
Governor housing
g
49- 59 N-m
-
(5.0 6.0 kg-m,
- -
- .-
---- -
IN-LINE TYPE INJECTION PUMP FEl!
Governor (Cont'd)
1. Attach injection pump with Tool KV11244852 (Universal
vise) and then remove feed pump and cover plate.
2. Install Tool between tappet adjusting bolt and nut.
Refer to Injection pump for tappet holder installation.
3. Remove diaphragm cover, pneumatic governor spring and

shims.
4. Remove diaphragm by pulling cotter pin out with pulling it

out from housing.
Be careful not to damage the diaphragm.
5.
(1) Remove mechanical governor cover gasket, push rod, spring
and shim.
(2) Attach timer and lock camshaft with Tool ST17080000

(DK57916432).
Remove r w n d nut with Tool DK57915010.
Governor (Cont'd)
(3) Remove flyweight with Tool.
6. Remove governor housing.
ASSEMBLY
Assemble governor in the reverse order of disassembly, noting
following item.
Do not install plate plug until idle adjustment is made.
1. Make sure that impeller is installed to the camshaft with flat
blade side toward governor.
2. Apply liquid sealant to new governor cover gasket.

(4) : Flyweight round nut
49 - 59 N-rn
(5.0 - 6.0 kgrn, 36 - 43 ft-lb)
3. Apply diaphragm oil to diaphragm.

CAUTION:
Do not allow gasoline to be left on diaphragm.
Use diaphragm oil.
IN-LINE TYPE INJECTION PUMP lI!?%l
Governor (Cont'd)
4. Coat caulking part of diaphragm and governor housing with
grease. Be careful not to allow grease to get on the diaphragm
su rface.
5. Adjust injection pump with a pump tester. Refer t o "Testing
lnjection Pump for Governor".
Test
PREPARATION
Injection pump test conditions
Nozzle KV11257800 -
-
7 -
Nozzle holder KV11257802
Nozzle starting pressure kPa (bar, kg/cm2, psi) 17,162 (171.6, 175.2.489)
Nozzle tube
KV11257805
Inner dia. x outer dia. x length mm (in)
2.0 x 6.0 x 600 (0.079 x 0.236 x 23.62)
Fuel feed pressure kPa (bar, kg/cm2, psi) 147- 157 (1.47- 1.57, 1.5-1.6.21 - 2 3 )
Fuel (test oil) IS0 41 13 or SAE Standard Test Oil (SAE J967d)
Fuel temperature "C (OF) 40-45(104-113)
Rotating direction Right (observed from the drive shaft)
Injection sequence 1-4-2-6-3-5

..
-- -
Test (Cont'd)
m
1. Prepare necessary service tools.
2. Remove fuel feed pump and cover plate.

3. Remove timer drive gear and attach coupling.
4. Install fuel injection pump on the bed of tester with Tool

KV11205781. Then attach timer t o pump.
5. Connect coupling to tester drive shaft with coupling disc.
6. Connect flexible hose from tester to injection pump.
7. Bleed air from injection pump.
..
--
---
- -- --- - - -
Test (Cont'd)
ADJUSTMENT
Adjusting injection timing
1. Adjust No. 1 injection timing.
(1 1 Remove injection tube, delivery valve holder, spring and valve
for No. 1 cylinder.
(2) Set a Tool to the pump housing.
(3) Rotate camshaft (pump tester) clockwise, and measure the

lift of 1st plunger when fuel flow from the measuring device
pipe stops.
Prestroke:
Refer to S.D.S.
2. If pre-stroke is not within specification, adjust injection

timing.
(11 Rotate camshaft until cam reaches T.D.C. position.
(2) Adjust the position of the adjusting bolt so that desired
pre-stroke can be obtained.
IN-LINE TYPE INJECTION PUMP j'iiz]
Test (Cont'd)
3. Adjust No. 2 to No. 6 cylinder injection timing.
(1) Set No. 1 cylinder t o injection start timing position, and set
angle scale on tester flywheel at "0"".
(2) Turn tester flywheel to the angle shown below, and make
sure that fuel flow from test nozzle stops.
If prestroke (injection timing) is incorrect, adjust the timing
by following step 2.
30' 30' 30'

angle
4. Check top clearance.

(1) Place the cam for each cylinder in the T.D.C. position.
(2) Insert a screwdriver between the tappet adjusting bolt
and lock nut.
(3) Lift the tappet using the screwdriver.
(4) Measure the top clearance using the measuring device.
(5) Ensure the top clearance is 0.3 mm (0.012 in) or more.
If the top clearance is less than 0.3 mm (0.012 in) readjust
the pre-stroke.
Adjusting injection volume

1. Remove control rack guide screw and install lock screw to
fix control rack on pump housing.
CAUTION:
Tighten lock screw by hand.
2. Set Tool DK05782618 to control rack.

(1) When setting tool, push control rack fully toward governor
side, and align the "0" on measuring device scale.
(2) Take off diaphragm housing together with governor spring.
Otherwise, " 0 position may not be obtained.
(3) Pull down full control lever toward fuel increasing side, and
check the stroke of control rack.
Control rack stroke:
Refer to S.D.S.
IN-LINE TYPE INJECTION PUMP l'YZ5-I
Test (Cont'd)
3. Set fuel feed pressure.
Fuel feed pressure:
147 - 157 kPa (1.47 - 1.57 bar,
1.5 - 1.6 kg/cm2, 21 - 23 psi)
4.
(1) Measure injection volume for each cylinder a t rated pump
speed and control rack position.
Injectionvolume:
Refer to S.D.S.
(2) Compute allowable imbalance of fuel injection volume.

Allowable imbalance =
for each plynger

x 100
Mean injection volume
Allowable imbalance:
Refer to S.D.S.
5. Adjust injection volume so that specified injection volume

and allowable imbalance are obtained.
(1) Loosen control pinion clamp screw.
(2) Place suitable tool into hole in control sleeve and adjust by
rotating control sleeve.
(3) After adjustment is completed, tightly secure pinion set
screw.
(4) Remove lock screw from control rack and reinstall guide
screw.
6. Install diaphragm housing and governor spring.
GOVERNOR
Adjustment
a. When making a governor performance test, maintain the
pump speed at 500 rpm.
b. Gradually step up negative pressure when adjusting.
c. Test and adjust injection timing and injection volume before
testing governor.
IN-LINE TYPE INJECTION PUMP I]
Test (Cont'd)
Air-tight test
1. Apply a negative pressure of 4.904 kPa (49.04 mbar, 500
mmH, 0, 19.69 inH, 0)t o governor with rack set at position
R1.
2. Make sure that negative pressure will not drop below the
specified value within 10 seconds.
Negative pressure:
4.904 - 4.707 kPa (49.04 - 47.07 mbar,
500 - 480 mmH, 0,19.69 - 18.90 inH, 011
more than 10 seconds
I f it drops in less than 10 seconds, c h d the diaphragm and
replace i f necessary.
Smoke setscrew adjustment

With no negative pressure applied, adjust the smoke setscrew
so that the rack is set at position R, .
Torque mechanism adjustment

1. Check that torque control spring starts to actuate at nega-
For torque control tive pressure PI and stops at P,. In other words, torque
spring adjustment
to start actuating control travel is R, - R,.
(or stop actuating)
Torque control travel: -
Refer to S.D.S.
For toque control travel 2. If torque mechanism adjustment is not within the specifi-
adjustment
cations:
( 1) Remove diaphragm.
E F454 (2) Add or remove shim(s) (two types) as required until correct
torque mechanism adjustment is made.
After installing diaphragm, make an air-tight test again.
IN-LINE TYPE INJECTION PUMP [El
Test (Cont'd)
High-speed adjustment (Pneumatic gwernor section)
1. Increase negative pressure. Adjust governor shim u n t i l there
is a balanced condition between rack position R, and nega-
tive pressure P, .
2. Gradually increase negative pressure. Make sure that negative
pressure is P, when rack is moved t o position R,.
Idle adjustment
1. With negative pressure kept at P, , t u r n idle spring screw in
w i t h T o o l u n t i l rack is set at position R, .
2. Tighten lock nut.
3. Further increase negative pressure. Make sure that negative
pressure is P, when rack is set at position R,.
I f necessary, replace idle spring as an assembly.
4. Install plate plug.
Apply adhesive t o t h e plug i n order t o prevent air leaks o r the
plug from detaching.
High-speed adjustment (Mechanical governor section) :
1. With negative pressure kept i n condition P,, increase pump
speed .
C
I 'I
-"
C
I
I
->
0
I
I t
I I
r
a ; :
5 I I
n
EF767A
..IR, :R, R3
Rack position mrn (in)
2. Adjust adjusting b o l t o f governor spring so t h a t pump speed

.
is N, when rack starts t o be pulled f r o m R,
If a b w e adjustment cannot be made properly by means o f ad-
justing bolt, add o r remove mechanical gwernor spring shim(s).
3. Increase p u m p speed, and make sure that pump speed is N,
when rack is set a t point R, .
If pump speed is within specified range, replace mechanical
gwernor spring and readjust.
4. Further increase pump speed, and make sure that rack is
set a t p o i n t R6 when pump speed is N,.
a. If rack is n o t properly set a t position R6, check f o r wear o n
pards) between flyweight and push r o d and f o r proper asem-
bly o f p u m p housing.
b. If necessary, replace push rod.
Feed Pump
After installing feed pump, bleed air from system.
TEST
Standard fuel feed volume
The volume of fuel displaced by the feed pump i s more than
405 mQ (14.3 Imp fl oz) for each 15 seconds a t 1,000 rpm.
The discharge pressure is 333 to 412 kPa (3.33 to 4.12 bar,
3.4 to 4.2 kg/cm2, 48 t o 60 psi) at 600 rpm.
Pump performance test

1. Connect a pipe to intake side of feed pump, and set pump so
that fuel can be sucked up from fuel level 1.0 m (3.3 ft)
below the pump.
2. Operate priming pump a t 80 strokes per minute, and make
sure that fuel can be sucked up in less than 25 strokes.
Air-tightness test
1. Stop up fuel feed pump discharge port and apply 147 t o 196
kPa (1.47 t o 1.96 bar, 1.5 to 2.0 kg/cm2, 21 to 28 psi) of
air pressure to intake side of pump.
2. Immerse pump in kerosene (light oil) and make sure that no
air leaks from any of pump connections. If bubbles larger
than one grain come from fuel feed pump housing or push
rod joint continuously, replace oil seal at push rod or push
rod.
Replace feed pump assembly, if necessary.
INSPECTION
Feed pump housing
1. Check check valve seats. If they are damaged or excessively
worn, replace housing.
2. Check push rod hole. If hole is excessively worn, replace
housing.
Check valve and check valve spring
1. If seat of check valve is excessively worn or scarred, replace
check valve with a new one.
2. If check valve spring is damaged or permanently stressed,
replace valve spring.
Piston and piston spring
1. If periphery of piston is excessively worn or scarred, replace
piston with a new one.
2. If piston spring is damaged or weakened, replace valve spring.
Tappet assembly
1. Tappet
If periphery of tappet is worn or scarred, replace it with a
new one.
IN-LINE TYPE INJECTION PUMP E!zl
Feed Pump (Cont'd)
2. Tappet roller
If periphery of tappet roller is excessively worn or scarred,
replace it with a new one.
~ o l l eto
r pin clearance:
Limit
0.30 mm (0.0118 in)
Tappet roller outside diameter:
Wear limit
14.9 rnm (0.587 in)
Timer
REMOVAL
1. Remove timing gear cover.
2. Remove timer round nut.
3. Remove timer assembly by threading in Tool.
INSTALLATION
1. Align crank pulley and timing gear case cover marks so that
No. 1 piston is a t top dead center.
2. Mesh injection pump drive gear with idler gear at Z-mark,

and then- align gear t o key way of injection pump camshaft
while turning crank pulley.
3. Secure timer assembly with lock washer and round nut.
: Round nut
59 - 69 N-m
(6 - 7 kg-m, 43 - 51 ft-lb)
4. Install timing gear cover with new gasket sealed.
ADJUSTMENT
1. Install stroboscope, using cover plate bolts, so that syn-
. chronizer lever attachment is applied to tappet.
2. Operate fuel injection pump, turn "ON" switch of strobo-
scope illuminating dial (angle scale) on flywheel, and measure
angular change based on variations in pump speed.
If tester does not have a dial (angle scale) :
(1) Attach a dial to timer coupling and mount a pointer on
tester drive shaft.
IN-LINE TYPE INJECTION PUMP E l
Timer (Cont'd)
(2)Operate fuel injection pump and turn stroboscope "ON"
so as to illuminate dial.
3. If advance angle is not within specified range, adjust by

changing timer spring shims.
a. When injection timing is retarded, decrease shim thickness.
b. When injection timing is advanced, increase shim thickness.
Timer advance curve:
Refer to S.D.S.
DISASSEMBLY
- -
9s in (10 - 18.72 130)
m59-69(6.0-7.0.43-51)
: N.m (kg-m, ft-lb) SEF775G
1. Place timer assembly on Tools with flyweight holder hole

positioned on base pin.
2. Remove injection pump drive gear.
IN-LINE TYPE INJECTION PUMP lfW2(
Timer (Cont'd)
3. Remove nut, lock washer, lock plate, adjusting shim and
thrust washer after unbending lock washer.
4. Remove timer flange by prying with lever while pressing

spring with Tool DK57916432.
5. Remove timer spring, adjusting shim and flyweight.
ASSEMBLY
1. Set flyweight holder on Tools with flyweight holder pin
hole positioned on base pin.
2. Apply grease to flyweight holder pin and flyweight holder

hole.
3. install flyweight and insert Tool under timer spring, posi-
tioning spring on flyweight.
IN-LINE TYPE INJECTION PUMP _ --_ _ m42
Timer ( Cont'dl
4. Insert suitable adjusting shim into hole a t pin part of timer
flange.
5. Cover timer flange to flyweight holder by matching notch of
flange and key groove of flyweight holder.
6.
(1) Turn Tool DK57916432 in direction to compress timer
spring, thread in Tool DK57924190, and then remove Tool
D K57932020.
(2) Using a lever, insert timer spring into flange hole, thread in
Tool DK57924190 all the way and install flange in i t s proper
position.
Make sure that spring is fully seated in holes in flange and fly-
weight holder.
7. Adjust flyweight holder and flange clearance.

(1) Install thrust washer, lock plate and adjusting washer, and
completely tighten them with nut.
[L1) : Nut
98- 177 N.m
-
(10 - 18 kg-m, 72 130 ft-lb)
(2) Measure lock plate and thrust washer clearance. -If the clear-
ance is not within specifications, adjust with adjusting
washer.
Lock plate and thnrst washer clearance:
0.02 - 0.10 mm
-
(0.0008 0.0039 in)
8. Align "0" mark on drive gear with notch in timer flange,

and install drive gear.
- ---
- - -- -
-- - - VE-TYPE INJECTION PUMP ITMZ I
Removal
1. Remove injection tube.
Cover the injection nozzle assembly with a plug to prevent dust
entry.
2. Remove fuel cut solenoid wire.
3. Remove accelerator wire and disconnect overflow hose, fuel

inlet hose and fuel return hose.
4. Remove injection pump drive gear cover.
5, Loosen injection pump drive gear nut and remove drive gear
by using puller.
VE-TYPE INJECTION PUMP [=I
Removal (Cont'd)
6. Remove injection pump fixing nuts and bolts.
I
7. Remove injection pump with injection tubes.

Disconnect injection tube from pump once it is removed.
lnstallation and Adjustment

1. Confirm that No. 1 piston is set at T.D.C. on i t s compres-
sion stroke.
2. Install injection pump.

(1) Temporarily set injection pump so that the flange of pump
is aligned with aligning mark on front cover.
(2) Install injection drive gear.
(ol : 59 - 69 N-m (6 - 7 kg-m, 43 - 51 ft-lb)
Make sure that the key does not fall into the front cover.
Make sure that "2" marks are aligned.
(3) Install drive gear cover with new gasket.
PLUNGER L l FT ADJUSTMENT
1. Remove plug bolt from distributor head and install measuring
device.
2. Loosen injection pump mounting nuts and mounting
bracket bolt.
3. Plunger lift measurement and adjustment.
(1) Turn crankshaft counterclockwise 20 to 25 degrees from
No. 1 piston at T.D.C.
(2) Find dial gauge's needle rest position at step (1) set position,
then set the gauge to zero.
VE-TYPE INJECTION PUMP k?!EJ
(3) Turn crankshaft clockwise until No. 1 piston i s set at T.D.C.
(4) Read dial gauge indication.
0.74k0.02 mm (0.0291k0.0008 in)
(equivalent to 6" B.T.D.C.)
(5) I f it is not within the above range, turn pump body until it
comes within standard range.
a. If indication is smaller than the specified value, turn pump
body counterclockwise.
b. If indication is larger than the specified value, turn pump
body clockwise.
4. Tighten injection pump securely.
PJJ : Injection pump fixing bolt
-
19 - 25 N.m (1.9 - 2.5 kg-m, 14 18 ft-lb)
Injection pump to mounting,bracket
-
30 - 41 N.m (3.1 4.2 kg-m, 22 - 30 ft-lb)
. ,
5. Disconnect dial gauge and reinstall plug bolt with new washer.
-
: 14 - 20 N.m (1.4 - 2.0 kg-m, 10 14 ft-lb)
6. Connect injection tubes.
: Flare nut
20 - 25 N.m (2.0 - 2.5 kg-m, 14 - 18 ft-lb)
7. Bleed air from fuel system.
IDLE AND MAXIMUM SPEED ADJUSTMENT

CAUTION:
a. Do not remove sealing wires unless absolutely necessary.
b. Disturbing full-load adjusting screw will change fuel flow
characteristics, resulting in an improperly adjusted engine.
Readjustment of fuel injection pump should be done using a
pump tester.
c. If maximum speed adjusting screw is turned in direction that
increases control lever angle, engine damage may result.
Throttle control wire adjustment

1. Turn idle control knob fully counterclockwise.
2. Make sure that clearance between idle control lever pin and
fuel injection pump control lever is within the specified
range.
Clearance:
-
1- 2 mm (0.04 0.08 in)
3. I f not within the specified range, adjust with idle control
wire adjusting nut.
4. After adjusting clearance, tighten lock nut.
VE-TYPE INJECTION PUMP F
l
Idle adjustment '
Maximum speed adjustment

Maximum speed adjusting screw is retained by sealing wire and
need not be adjusted under normal circumstances. However, if
it becomes necessary to adjust it, the following procedure should
be followed:
1. Start engine and warm it up until coolant temperature indi-
cator points to middle of gauge.
2. Connect tachometer's pick-up to No. 1 fuel injection tube.
To obtain accurate reading of engine rpm, remove clamps that
secure No. 1fuel injection tube.
3. Depress accelerator pedal fully under no load and, a t this
point, read the tachometer indication.
Maximum engine speed (Under no-load):
4 , 6 a 100 rpm
- -
Sealing wire
-
4. I f indication is lower than specified maximum engine speed,
turn maximum speed adjusting screw counterclockwise 1 or
2 rotations. Then depress accelerator pedal to floor under no
load and, at this point, read indication.
5. I f indication is still lower than specified speed, repeat step 4
above until specified engine speed is reached.
6. After adjustment, tighten lock nut securely.
7. Wind up with a sealing wire.
EFm8 Disassembly
PREPARATION
Before performing disassembly and adjustment, test the
fuel injection pump and note test results.
Prior to beginning disassembly of fuel injection pump, clean
all dust and dirt from its exterior.
Disconnect overflow valve and drain fuel.
Clean work bench completely, removing all foreign matter.
Collect only those service tools necessary for disassembling
and reassembling.
Be careful not to bend or scratch any parts.
Q
Governor control lever
- - -
1.8 2.6 (0.18 0.25, 1.3 1.8)
Fuel cut solenold valve

Maxlmum speed adjusting
: N.m (kg-m, ft-lb)

-
-
- -- SPECIAL SERVICE TOOLS
rt device KV11229072
KV11229820
Socket wrench
KV11214110
KV11229042
Measuring device
(For measuring dimensions Feed pump holder
"K" & "KF") KV 11229542
Socket wrench (For pivot bolt)
1. Remove governor cover.

(1) Remove nut, spring washer, spring seat and spring from
control lever.
(2) Check aligning marks on control lever and control shaft.
c (3)Remove governor cover.

2. Remove control shaft from tension lever.
3. Remove governor shaft with special service tool.

Loosen lock nut by turning it clockwise.
4. Remove governor sleeve, washer and flyweight, along with

flyweight holder, then remove washer and shims.
5. Remove plug with special service tool.

VE-TYPE INJECTION PUMP @El
Disassembly (CQnt8d)
6. Remove delivery valve holder, spring, delivery valve and
gasket.
Distributor head has letters (A, ,B, C, D) stamped o n it.
Remove lettered parts in alphabetical order and arrange neatly.
7. Remove fuel cut solenoid valve.
8. Remove distributor head.

Be careful n o t t o drop the two support springs and guide pins.
9. Remove plunger assembly.

L i f t plunger, along w i t h control sleeve, shim, spring seat, plunger
spring, washer and shim.
10. Loosen .left and right governor pivot bolts.

VE-TYPE INJECTION PUMP Em
11. Remove governor pivot bolts and lever assembly.
Avoid pulling on start spring and start idle spring.
12. Remove shim, cam disc, spring and driving disc.
13. Remove clips and pins.
14. Move adjusting pin to center of roller holder, as shown.

VE-TYPE INJECTION PUMP F!El
15, L i f t out roller holder with rollers without tilting.
Be careful not t o drop rollers.
16. Attach oil seal guide onto the drive shaft and then remove
drive shaft.
a. Be careful not t o scratch inner surface o f fuel injection pump
body.
b. Remove drive gear side key.
.:.
c. Be careful n o t t o drop the key.
17. Remove speed timer cover, O-ring, shims, spring, piston and
slider.
18. Remove regulating valve with special service tool.
19. Loosen screw from feed pump cover.

. . VE-TYPE INJECTION PUMP -
p5.l
20. Remove cover and feed pump assembly as a unit.
1) Insert feed pump holder (KV11229542) into fuel injection
pump housing.
2) Turn injection pump upside down, as shown.
3) Remove cover and feed pump assembly as a unit.
a. If cover and feed pump assembly are hard to remove or
stuck midway, strike the pump body lightly.
b. Do not change positions of vanes.
Inspection
1. Wash all parts completely.
2. Replace worn or damaged parts.
3. Control edge of plunger must be sharp and contact surfaces
must not exhibit any noticeable running tracks. If the con-
dition is not good, replace plunger.
4. Check for height of all rollers.
Difference .in maximum and minimum roller height should be
less than 0.02 mm (0.0008 in).
Assembly
Always replace the following service parts as assembly units.
Distributor head, control sleeve and plunger
Feed pump assembly (pump impeller and vanes with eccen-
tric ring)
Plunger spring kit
Roller assembly
Flyweight kit
Governor lever assembly
PREPARATION .-
Dip all movable parts and O-rings in test oil, then clean.
1. Set feed pump cover, rotor with vanes, and ring on special
service tool KV 11229542.
1) Align the three holes in feed pump cover and ring. . .
2) Do not change positions of vane.
3) Holes A and B in ring are not equally spaced to inner wall
of ring.
2. Install feed pump cover, rotor with vanes, and ring t o pump
housing.
Be careful to install ring correctly. If left and right are reversed,
fuel will not be discharged from feed pump.
VE-TYPE INJECTION PUMP E!El
Assembly (Cont'd)
When fuel injection pump rotates in direction "R"
The following description applies to fuel injection pumps that
rotate in direction "R".
3. Turn fuel injection pump 180°, and remove special service
tool KV11229542. Tighten screw to retain pump cover.
a. . When tightening screws, be careful not to scratch inner wall
of pump housing.
b. After tightening screws, make sure that rotor with vanes
moves smoothly.
4. Make sure that drive shaft and gear are assembled properly,
as shown.
5. Attach oil seal guide onto the drive shaft, then install drive
shaft .to housing while key in drive shaft engages with key
groove in rotor.
6. Set drive shaft's nail parallel to timer.

7. Install roller and holder.
a. Do not interchange roller positions. If they are interchanged,
refer to Inspection for correction.
b. Make sure that washer is situated outward of rollers.
8. Align holder and timer adjusting pin holes.

Assembly (Cont'd)
9. Install timer piston and slider as a unit.
a. Make sure that hole in slider faces towards roller holder.
b. Make sure that concave hole in piston is on same side as
return hole.
10. Insert timer adjusting pin into timer piston slider, and secure
with retaining pin and clip.
Make sure that timer piston moves smoothly.
11. Install timer, using a 0.6 rnm (0.024 in) thick shim, then
install timer spring, shim, O-ring, and cover, in that order.
a. Use at least one shim on each side of timer spring.
b. Use shims that were selected during bench test.
12. Install regulating valve.

Be careful not to scratch O-rings.
/ 13. Install driving disc with i t s concave side facing up.

VE-TYPE INJECTION PUMP lE!!zl
Assembly (Cont'd)
14. Measurement of plunger-springset length (dimension "KF")
.Dimension "KF" is the distance between the end face of the
distributor barrel and the end face of the plunger.
( 1 Install distributor head, as shown.
Do not insert shim into "A" portion before measuring.
1 Spring seat
2 Plunger spring
3 Guide pin
4 Distributor head
5 Dinributor barrel
6 Spring seat
7 Washer
8 Shim
9 Plunger
SEF362F
(2)Set dial gauge so that it can compress 0 to 10 mm (0 to

0.39 in), and reset to zero.
(3) Apply force (not enough to compress plunger spring) to

plunger's bottom in axial direction, and measure dimension
KVl1m 2 "KF" with dial gauge, as shown.
(Shim is insetted.)
SF856
(4) Determine the shim to be used by calculating difference

between standard and measured dimensions.
Standard dimension "KF":
-
5.7 - 5.9 mm (0.224 0.232 in)
[Example]
When measured (dial gauge reading) value is 5.2 mm,
5.7 mm - 5.2 mm = 0.5 mm (shim thickness t o be used)
. . VE-TYPE INJECTION PUMP bEI
Assembly ( Cont'd)
a. When there are n o shims available o f a thickness which
matches specified dimensions, use slightly thicker shims.
b. Use selected shim with distributor head in step 14-(3) above.
c. Use the same size shim o n each side o f distributor head.
d. Shims are available in seven different thicknesses.
Thickness
Part numbar
mm [in)
16882-V07W 0.5 (0.0201:

- - - --
18882-V0701 0.8 40.0311
16882-V0702 I .O (0.0391
18882-V0703 1.2 (0.047)
18882-V07Q4 1.6 (0.0591

18882-VO705
1 1.8 (0.071)
1gee2-Wl708 2.0 (0.0791
I
15. Adjustment of plunger dimensions (Measurement of dimen-
sion "K")
Dimension "K" is the distance from the end face o f the distri-
butor barrel t o the end face o f the plunger top, when the plunger
is at the bottom dead center position.
( 1) Install parts as shown.
a. Do not install "spring" o n driving disc.
b. When inserting plunger and shim into cam disc, make sure
that drive pin is situated i n groove at bottom o f plunger.
1 Drive shaft 7 Spring seat

2 Driving disc 8 Shim
3 Shim 9 Distributor barrel
4 Spring seat 10 Washer
5 Plunger spring 11 Shim
6 Guide pin 12 Cam disc
SEF370F
(2) Using a dial gauge, measure dimension as shown.

a. Rotate drive shaft so that plunger is set at bottom dead
center.
b. Securely mount distributor head with screws.
... VE-TYPE INJECTION PUMP E@l
Assembly (Cont'd)
(3) Determine shim t o be used b y calculating difference between
measured (dial gauge reading) value and standard dimension
"K", and position that shim o n plunger's bottom.
-
"K" = 3.2 3.4 m m
(0.126 - 0.134 in)
a. When measured value is greater than standard dimension
"K", use a thicker shim.
b. After shim has been positioned, measure dimension again t o
ensure that it is correct.
c. - Shims are available in 25 different thicknesses.
16. Install spring in t o p of driving disc, then install cam disc

and shim.
Make sure cam disc drive pin and drive shaft key way face
upwards.
VE-TYPE INJECTION PUMP [TW~]
Assembly (Cont'd)
17. Install governor lever.
Avoid pulling o n start spring and start idle spring.
18. Install plunger assembly.

a. Make sure control sleeve is installed with its small hole
facing spring seat side.
SEF522
b. Insert ball pin for governor lever into hole in control sleeve
(shown by arrow).
Governor lever
19. Apply a coat o f grease t o guide pin, shim and spring seat,
and attach these parts t o distributor head.
20. Install distributor head.

a. Always face support spring toward governor lever.
b. Be careful n o t t o drop spring.
c. Make sure that ball pin f o r governor lever is inserted pro-
perly into hole i n control sleeve.
d. After installing distributor head, make sure that plunger
spring is at guide pin i n spring seat.
-
VE-TYPE INJECTION PUMP kEl
Assembly (Cont'd)
21. Tighten distributor head.
: Distributor head bolts
-
10 - 14 N-m (1.0 - 1.4 kg-m, 7 10 ft-lb)
22. Attach flyweight assembly.

When installinggovernor shaft, be careful not to scratch O-rings.
Gwemor
shah
Flyweight
assembly
SEFS02
23. Adjust dimension "L".

ldL*t:
1.5 - 2.0 mm (0.059 - 0.079 in)
a. Tighten lock nut to specified torque.
-
f l : 17 22 N.m (1.7 - 2.2 kpm, 12 - 16 ft-lb)
b. Governor shaft has a left-hand thread for injection pumps
designed to rotate in "R" direction, and a right-hand thread
for those rotating in "L" direction.
VE-TYPE INJECTION PUMP F a
Assembly (Cont'd)
24. Measure axial play of flyweight holder. I f it is not within
specified range, adjust it by means of shims.
"L":
-
0.15 - 0.35 mm (0.0059 0.0138 in)
Shims are available in 5 different thicknesses.
Thickness
Part number
mm (in)
19203-V0700 1.05 (0.0413)
19208-V0701 1-25 10.0492)
19208-V0702 1.45 (0.0571)

-
-
1920&VO703 1-65 (0.0850)
192llsVMW 1.$5 (0.0728)
25. Measurement-of dimension "MS" (for determining starting

amount of fuel injection)
Dimensions "MS" is the distance between closing plug and start
lever.
( 1 Remove lock nut and governor shaft.

VE-TYPE INJECTION PUMP FEl
Assembly (Cont'd)
(2)Install special service tool at governor shaft position.
(3) Install special service tool (block gauge) to Pump housing.
(4) Install special service tool (dial gauge) with rod.
(5) Push governor steeve against flyweight Hold governor sleeve

in that position and set dial gauge to zero.
(6) Push tension lever until it touches stopper pin. Back governor
sleeve up until start lever touches tension lever. A t this point
read dial gauge.
MS: Refer to S.D.S.
Assembly (Cont'd)
(7) If dial gauge indication is not within this range, replace
closing plug and adjust dimension "MS" to tharrange.
- -
Locking cap Closing plugs are available in 8 different tenghs.
"P Part nurnbar bngth

-(in) -
16268RB100 3.10 (0.1220)
CI-inq PI 16268-R8101 3.30 (0.12991
SEF620G 1828&R8102 3.50 (0.13T8)
16288R8ta3 3-70 (aI457l
16268R8104 3.90 L0.1635)
1 W R 8105 4.10 (0.1614)
16288R8106 430 ( ~ t ~ s 3 1
16288R8107 4.50 (0.7 7 7 ~ 1
26. Install control lever shaft.

Apply a coat of grease to lever shaft end.
27. lnstall governor cover.
VE-TYPE INJECTION PUMP k!El
Test
PREPARATION -
Nozzle KV11257805
Nozzle holder KV 11257802
Nozzle starting pressure kPa (bar, kg/cm2, psi) 14.711 - 15,201 (147.1 - 152.0, 150- 155,2,133- 2,204)
- -- - .
Nozzle tube
Inner dia. x outer dia. x length KV11205032
mm (in) 2.0 x 6.0 x 840 (0.079 x 0.236 x 33.07)
Fuel feed pressure kPa (bar, kg/cm2, psi) 20 (0.20, 0.2, 2.8)
~ u e(test
l oil) IS0 41 13 or SAE Standard Test Oil (SAE J967d)
Fuel temperature "C (OF) 4 5 - W ( 1 1 3 - 122)
Rotating direction Right (observed from the drive shaft)
Injection sequence 1-4-2-6-3-5
1. Prepare necessary service tools.
KV11229522
KV 11242442
KV11205032
Test oil should be IS0 4113, SAE Standard Test Oil (SAE J967d)
or its equivalent.
VE-TYPE.INJECTION PUMP lEcl
Test (Cont'd)
3. Install fuel injection pump to pump tester.
4. Connect necessary piping.
1 Fuel supply inlet from pump tester

2 Overflow valve
3 Coupling
4 Fixing stand
SEF378F
5. Make sure that governor shaft is properly installed.

P3) : Governor shaft lock nut
- -
17 - 22 N-m (1.7 2 2 kgm, 12 16 ft-lb)
'
6. Run fuel injection pump as follows:

(1) Maintain test oil in tank at 45 to 50°C (113 to 122°F).
(2) Set control lever at "full-load" using a spring.
Set maximum speed adjusting screw in position shown, by turn-
ing it counterclockwise.
fl: Refer t o S.D.S.
fi- m*.#-'z SEF621G

(3) Furnish specified voltage of 12 volts to fuel-cut solenoid
valve to activate it.
(4) Rotate fuel injection pump by hand to see if it moves
- - - - -
smoothly.
5 : A (5) Rotate fuel injection pump at 300 rpm to make sure that all
air inside pump chamber is discharged through overflow
valve.
(6) Set feed oil pressure a t 20 kPa (0.20 bar, 0.2 kg/cm2, 2.8 psi).
(7) Run fuel injection pump at 1,000 rpm for ten minutes.
If fuel leakage, fuel injection failure or unusual noke is noticed,
immediately stop pump tester operation and check fuel injection
pump for abnormalities.
VE-TYPE JNJECTiON PUMP
Test (Cont'd)
AOJUSTMENT
Preadjust full-load delivery
1. Set control lever a t "full-load" using a spring.
Set maximum speed adjusting screw in position shown, by turn-
ing it counterclockwise. Refer to step 6-(2) in Preparation.
2. Furnish specified voltage of 12 volts to activate fuel cut
solenoid valve.
3. Rotate fuel injection pump a t 1,100 rpm, and measure
amount of fuel injection.
Standard fuel injection:
Refer to S.D.S.
4. If fuel injection is less than standard, adjust it with full-load

adjusting screw.
Turn adjusting screw clockwise to increase fuel injection.
Adjustrnern of feed pump pressure

1. Repeat steps 1 and 2 outlined under "'Preadjust Full-Load
Delivery" heading.
2. Measure feed pump pressure a t specified fuel injection pump
rpm. .
Standad pump pressure:
Refer to S.D.S.
a. When measured pressure is lower than specifications.

Push in plug that is driven into regulatingvalve body.
Be careful not to push plug in too far.
VE-TYPE INJECTION PUMP Fl!
Test (Cont'd)
b. When measured pressure is higher than specifications.
Remove regulating valve from fuel injection pump, and dis-
assemble regulating valve using service t o o l K V 1 1229462.
Drive plug o u t until it is flush w i t h end face o f regulating valve.

Install spring, piston and spring ring, i n that order, t o regulating
valve.
Make sure that spring ring is flush w i t h end face o f regulating
valve body when it is pushed in.
Attach regulating valve t o fuel injection pump.

: Regulating valve
8 - 9 N-m
- -
(0.8 0.9 kg-m, 5.8 6.5 ft-lb)
Adjust supply pump pressure t o specifications. Refer t o step
2-a.
Adjustment of speed timer

1. Repeat steps 1 and 2 outlined under "Preadjust Full-Load
' Delivery" heading.
,, 2. Remove cover f r o m high-pressure side (side without spring)
I o f timer, and attach service t o o l KV11282815 t o that side.
3. Measure timer piston strokes at specified fuel injection pump

rpm indicated below.
Standard timer piston stroke:
Refer to S.D.S.
Test (Cont'd)
4. I f timer piston stroke is not within specified range, remove
cover from low-pressure side of timer and adjust piston
: stroke by adding shim(s).
a. Shims (service parts)
Thickness
Part number
mm (in)
16880.V0700 0.6 (am)
16880-VM01 0.7 (0.028)
18880-V0702 0.9 (0.035)

18gBOVO703 1.0 {O.wSl
118QV0704 1.2 (0.047)
lgSSMllTo0 2.4 (0.094)
b. Make sure that at least one shim is used on each side of timer
spring.
Adjustment of fuel injection under full-load

1. Set control lever at "full-load" using a spring.
solenoid valve.
3. Measure fuel injection at each specified fuel injection pump
rPm.
Refer to S.D.S.
4. I f fuel injection is not within standard range, adjust it using

full-load adjusting screw.
Adjustment of fuel injection during idle

1. Pull spring until control lever touches idle speed adjusting
screw.
solenoid valve.
3. Measure fuel injection a t specified fuel injection pump rpm.
Refer t o S.D.S.
Test (Cont'd)
4. I f fuel injection is not within specified range, adjust using
idle speed adjusting screw.
a. Tightening this screw will increase fuel injection amount.

b. Make sure that control lever angle (a)i s set at the specified
range.
&: Refer t o S.D.S.
If control lever angle is not within specified range, adjust it
by repositioning control lever on control shaft. (One serra-
tion pitch: 15"1
After control lever has been repositioned, be sure to measure
amount of fuel injection at idle speed again.
Adjustment o f fuel injection during start

1. Set control lever at "full-load" by pulling spring.
solenoid valve.
3. Measure fuel injection at specified fuel injection pump rpm.
Refer to S.D.S.
4. I f fuel injection is lower than standard, check, "MS. dimen-

sion. Refer t o step 25 for Injection Pump Assembly.
Adjustment of fuel injection at maximum pump rpm

solenoid valve.
3. Measure fuel injection at specified fuel injection rpm.
Refer to S.D.S.
4. I f fuel injection is not within standard range, adjust using

maximum speed adjusting screw.
- . VE-TYPE iNJECTION PUMP
Test (Cont'd)
a. Tightening screw will increase fuel injection.
b. Make sure that control lever angle (PI is within the specified
range.
8: Refer t o S.D.S.
fi- m7J
-
2z:'-
b ',.c,+'
*-=-
I
SEF62lG
Measurement o f overflow amount

2. Furnish specified voltage of 12 volts t o activate fuel cut
solenoid valve.
3. Measure fuel overflow at specified fuel injection rpm.
Fuel overflow:
43 - 87 mP
-
t1.51 3.06 Imp floz)/lO sec. at 1,100 rpm
. Operation check of fuel cut solenoid valve

When engine is idling and fuel cut solenoid valve current is OFF,
be sure there is no injection. This check has t o be done for
approx. 5 seconds.
INJECTION NOZZLE F!?J
Removal and Installation
1. Remove injection tube assembly.
2. Remove spill tube assembly.
To prevent spill tube from breaking, remove it by gripping nozzle
holder.
3. Remove injection nozzle assembly using deep socket wrench.

4. Install injection nozzle holder in the reverse order of removal.
(cs) : Injection nozzle holder t o cylinder head
54 - 64 N.m
- -
(5.5 6.5 kg-, 40 47 ft-lb)
Spill tube nut
29 - 39 N.m
(3.0 - 4.0 kg-m, 22 - 29 ft-lb)
Injection tube flare nut
-
20 25 N-m
-
(2.0 - 2.5 kg-, 1 4 18 ft-lb)
a. Nozzle gaskets should always be replaced.
b. To prevent spill tube from breaking laber, spill tube nuts
should be tightened gradually in sequence.
5. Bleed air from fuel system.
Refer t o BLEEDING FUEL SYSTEM.
Disassembly
1. Loosen inlet connector while keeping nozzle top from
turning.
Use vise jaw cwer t o avoid damaging the n w l e holder body.
2. Arrange all dkssembled parts in order shown at left.

INJECTION NOZZLE
Inspection
Thoroughly dean all disassembled parts with fresh kerosene or
solvent.
If nozzle needle is damaged or fused, replace nozzle assembly
with a new one.
If end of nozzle needle is seized or excessively discolored,
replace nozzle assembly.
Check nozzle body and distance piece for proper contact. If
excessively worn or damaged, replace nozzle assembly or
nozzle holder assembly.
Check distance piece and nozzle holder for proper contact. I f
excessively worn or damaged, replace nozzle holder assembly.
0 , Check nozzle spring for excessive wear or damage. I f exces-
sively worn or damaged, replace nozzle holder assembly.
Cleaning
1. Clean nozzle assembly using the nozzle cleaning kit
(KV11289004). nozzle oil sump scraper (KV11290632) and
nozzle seat scraper (KV 11290620).
2. Portions which should be cleaned are indicated in the left

figure.
Inlet connector
Nozzle needle
3. Remove any carbon from exterior of nozzle body (except

wrapping angle portion) by using Tool.
INJECTION NOZZLE E??El
Cleaning (Cont'd)
4. Clean fuel sump of nozzle body using Tool.
5. Clean nozzle seat by using Tool.

This p b should be performed with extra precautions, since effici-
ency of nozzle depends greatly on a good nozzle seat.
6. Clean spray hole of nozzle body by using Tool.

To prevent spray hole from canting, always dean it by starting
with inner side and working towards outside.
7. Decarbon nozzle needle tip by using Tool.
8. Check needle for proper position.

( 11 Pull needle about halfway out from body and then release it.
(2) Needle should sink into body very smoothly from just i t s
own weight.
(3) Repeat this test and rotate needle slightly each time.
If needle fails to sink smoothly from any position, replace both
needle and body as a unit.
INJECTlON NOZZLE IT M ~I
Assembly
Assemble in the reverse order of disassembly.
[01 : Inlet connector t o nozzle holder
29 - 49 N-m
(3.0 - 5.0 kgm, 22 - 36 ft-lb)
Test and Adjustment

WARNING:
When using nozzle tester, be careful not t o allow fuel sprayed
from nozzle t o come into contact with your hand or body, and
make sure that your eyes are properly protected with goggles.
I 1 INJECTION PRESSURE TEST
EF791A
2. Pump the tester handle slowly (one time per second) and
watch the pressure gauge.
3. Read the pressure gauge when the injection pressure just
starts dropping.
Initial injection pressure:
-
Used 9,807 10,297 kPa
- -
(98.1 103.0 bar, 100 105 kg/cm2 ,
1,422 - 1,493 psi)
New 10,297 - 11,278 kPa
- SEFt372A
-
(103.0 - 112.8 bar, 105 115 kg/cm2 ,
-
1,493 1,635 psi)
New nozzie is required t o always check initial injection pressure.
INJECTION NOZZLE 1~6G-j
Test and Adjustment (Cont'd)
4. To adjust injection pressure, change adjusting shims.
a. Increasing the thickness of adjusting shims increases initial
injection pressure. Decreasing thickness reduces initial pres-
sure.
b. A shim thickness of 0.04 mm (0.0016 in) corresponds approx-
imately to a difference of 471 kPa (4.71 bar, 4.8 kg/cm2, 68
psi) in initial injection pressure.
Thickness mm (in) Part number
0.1 (0.004) 1661343600

0.2 (0.008) 1661343601
0.3 (0.01 2) 1661343602
0.4 (0.016) 1661343603
0.5 (0.020) 1661343604
0.52 (0.0205) 1661343605
0.54 (0.0213) 16613-43606
0.56 (0.0220) 1661343607
0.58 (0.0228) 1661343G08
0.8 (0.031) 1661343609
LEAKAGE TEST
1. Maintain the pressure at about 981 to 1,961 kPa (9.8to 19.6
bar, 10 to 20 kg/cm2, 142 to 284 psi) below initial injection
pressure.
2. Check that there is no dripping from the nozzle tip or around
the body.
3. If there is leakage, clean, overhaul injection nozzle or replace
4 it.
Good Faulty
err"
SE F674A
SPRAY PATTERN TEST

I. Pump the tester handle 4 to 6 times per second or more.
2. Check the spray pattern.
3. If the spray pattern is not correct, clean injection nozzle or
replace it.
Good Wrong
EF794A
Air should be bled out of fuel system when injection pump is
: removed or fuel system is repaired.
.. Protect pump and engine mounts from fuel splash with rags.
I f engine will not start after bleeding air, loosen injection tubes
at nozzle side and crank engine until fuel overflows from injec-
tion.tube. Tighten injection tube flare nuts.
I f the engine does not operate smoothly after it has started, race
it two or three times.
In-line Pump
1. Remove the cap that covers the priming pump @ .
2. Turn the priming pump @ counterclockwise.
3. Loosen the air vent screws @ .
4. Move the priming pump @ up and down until no further air-
bleed comes out of the air vent screws @.
5. Tighten the air vent screws @.
6. Push and turn the priming pump clockwise.
7. Install the cap.
VE Pump
1. Loosen the air vent screw @ .
2. Move the priming pump @ up and down until no further air-
bleed comes out of the air vent screw @.
3. Tighten the air vent screw @ .
4. Move the priming pump @ up and down until there is
suddenly more resistance in the movement.
Checking Priming Pump

VE PUMP
Before checking priming pump, make sure that fuel filter is
filled with fuel.
1. Disconnect fuel return hose. .
Place a suitable container beneath hose end.
2. Pump priming pump and check that the fuel overflows
from the hose end. I f not, replace priming pump.
. ...- . . ' FUEL FILTER
,.. .
.. .
. .
.
- - lTDlZl
.,
Overflow Valve '
IN-LINE PUMP -
- Attach a pressure-gauge to fuel filter discharge port, and check
. valve opening.pressure by operating priming pump. If pressure
-
i s not within range of 98 to 137 kPa (0.98 to 1.37 bar, 1.0 to
Overflow valve . 1.4 kg/cm2 , 14 to 20 psi), replace overflow valve.
opening p-re
-
98 137 k ~ a
-
(0.98 1.37 bar,
-
1.0 1.4 kg/cm2, 14: 20
CRANKCASE EMISSION CONTROL SYSTEM ITO42 1
Description
Fresh air --.- The closed-type crankcase ventilation system is utilized as a
Blow-by gas- crankcase-.emissioncontrol system.
Air contrd valve The--closed-type crankcase emission control system prevents
blow-by gas from entering the atmosphere and keeps the internal
**
crankcase pressure constant.
During the valve operation, the blow-by gas is fed into the intake
manifold by the air control valve.
This is activated by the internal rocker cover pressure. When the
intake air flow is restricted by the throttle chamber, the internal
rocker cover pressure decreases. At this point, the crankcase
emission control valve keeps the internal r6cker cover pressure
constant so that air or dust is not sucked in around the crank-
shaft oil seal.
SEF432F
Inspection
AIR CONTROL VALVE
1. Remove rocker cover.
2. Remove control valve from rocker cover.
3. After plugging the center hole with adhesive tape, check that
air flows from inlet by blowing air from outlet and that air
does not flow by inhaling air.
SE F060B
Ventilation Hose
1. Check hoses and hose connections for leaks.
2. Disconnect all hoses and clean with compressed air.
If any hose cannot be freed of obstructions, replace.
SEaQ2
-- -
QUICK-GLOW SYSTEM lE!zl
Schematic
QUICK-GLOW SYSTEM 1~ ~ 4 2 1
Wiring Diagram
. -
.. -
--
-- - QUICK-GLOW SYSTEM E?!EJ
Description , '
------ When not crank~ng
. -
OFF
Indicator
OFF r
ON
Relay
4
Glow Plug
'.,'.
Temperature ,
Elapsing time
*
SE L337J
When the ignition switch i s turned-on, the relay is turned on and the "high-level" electric current flows
through the glow plugs and heats .them up quickly. After TI seconds have passed, the control unit turns off
the glow indicator but the relay remains on. The relay chops the electric current when the ignition switch
turns to "START" from-"ON".
The relay has been chopping for T, seconds after the ignition switch has returned to "ON" from "START".
When not cranking, the relay chops . the
. electric current while T, - T, seconds after the ignition switch has
turned to "ON" from-"OFF".
T, : approx. 2 - 6 [sec.] (Varies with coolant temperature.)
T, : approx. 3 - 14 [sec.] (Varies with glow plug terminal voltage.)
T, : approx. 15 [sec.]
T, : approx. 15 [sec.]
When the ignition switch is repeatedly turned "ON" and "OFF", T, becomes shorter.
QUICK-GLOW SYSTEM ITO42 J
. Engine fails to start or is hard to start.
Check fuel level, fue!supplying system, starter motor,-etc.
N.G.
I
4
Check that all glow plug connecting ;late nuts
Correct. are installed properly. Refer t o "Glow Plug
Connecting Plate Nuts Check."
- - - --
I O.K.
Turn ignition switch OFF for more than 10 seconds.

I
Check if glow indicator comes on in a few seconds.when the ignition switch i s turned t o ON.
I I
Check for a burned out bulb. Rep[& bulb.
-.
Check" for glow control unit.

* and
Check harness between fuse
glow control unit.
I
Replace glow control unit.

Control Check".
Check short circuit on harness

between ignition switch and
glow indicator.
QUICK-GLOW SYSTEM P!Z,l
(From previous page)
'I'
Replace glow plug.
1
I O.K.
( O.K.
Check harness between glow control
unit and ignition switch.
O.K.
Go to "Glow Control Check". Replace glow control unit.
Check harness between

glow control unit and glow relay
glow relay and glow plug
QUICK-GLOW SYSTEM .
Check
GLOW PLUG CONNECTING PLATE NUTS CHECK
Check that all glow plug connecting plate nuts and harness nut
are installed securely.
a .
GLOW PLUG CHECK

Remove glow plug connecting plate and perform continuity
test between each glow, plug-andcylinder head.
No continuity ... Replace glow plug.
r
GLOW RELAY CHECK
The glow relay is normally open.
For check, refer to STANDARDIZED RELAY.
Ohmmeter
SEL778H
WATER TEMPERATURE SENSOR UNIT CHECK

Measure resistance to temperature as shown.
Coolant temp. O C (OF) Resistance kSZ
.- -
-26 (-1 3)
-
- .
-
19
0 (32) S.6
20 i6W 2.5
40 (104) 1.2
QUICK-GLOW SYSTEM k!4
. Control Unit Check
POWER SUPPLY CIRCUIT CHECK
Disconnect harness connector from glow control unit and per-
fotm vokage check and continuity check.
-.
Vokmeter tvminals lgnition switch positinn
(+) (-1 OFF ACC ON
0 0 OV OV Approx. 12V
Ohmmeter terminals
lgn~t~o OFF
sw~tch
n
(+I (2)
@ Body .g~wnd Continuity exists
WATER TEMPERATURE SENSOR CIRCUIT CHECK

Check continuity between terminals @ and 0.
Measure resistance to temperature approximately as shown
in 'Water temperature sensor check".
START SIGNAL INPUT CHECK

1. Turn ignition switch OFF.
2. Disconnect harness connector from the starter motor's "S"
terminal.
3. Check terminal voltage between @ and 0 when the ignition
switch is at "START".
Voltage: approx. 12V
GLOW INDICATOR CONTROL CHECK

2. Leave harness connector joined to glow control unit.
3. Connect test lamp to glow control unit as shown.
4. Turn ignition switch to ON and measure the time the test
lamp stays lit
Time the test lamp should stay lit.
Approx. 2 - 6 seconds.
(Varies with coolant temperature)
.*
QUICK-GLOW SYSTEM ITM2I
Control Unit Check (Cont'd)
GLOW CONTROL CHECK
2. Leave harness connector joined to glow control unit.
3. Connect test lamp to glow control unit as shown.
. 4. Turn ignition switch to ON and measure the time the test
lamp stays lit.
Time the test lamp should stay lit.
Approx. 3 - 14 seconds. ..
(Varies with glow plug terminal voltage)
The time will be shortened if ignition switch is OFF only a short

time.
Therefore, when measuring the time, leave ignition switch OFF
for more than 1minute, and then turn ignition switch to ON.
This time, the test lamp came on and went off approx. 1 - 3
times after which it stayed lit.
5. When ignition switch is turned to START and returned to
ON, the test lamp comes on and goes off approx. 3 - 6 times.
INJECTION PUMP CONTROL. SYSTEM l~D42 I
Description
. -
FUEL EXCESS OPERATION
I N J E C T I O N PUMP CONTROL UNI T

(D.P.C. m o d u l e )
, D 0 f W@C 8 88T'tBQPt
11 tr 41 o
O I L PRESSURE
INJECTION PUMP
CONTROLLER
BATTERY
S C ~ X
When the starting switch is turned t o 'START", the fuel injection control unit activates. This permits an
electrical current to flow in sequence via rotor A of the fuel injection pump controller, from terminal 0 t o
rotor A and terminal C, causing the fuel injection controller motor t o run.
As the motor runs, rotor A rotates and, when it reaches i t s start position, current flow between terminat 0
I
M
and C is broken, which stops the motor's operation. The controller i s thus brought to i t s I position.
INJECTION PUMP CONTROL SYSTEM p j
Description ( C o n t ' d )
DRIVE OPERATION
. - . . -
(D.P.C. m o d l~e)
. .
- - SELB5SK
When the starting switch is turned from "START" to "ON", the fuel injection pump control .unit activates.
This permits an electrical current to flow in sequence via rotor A of the fuel injection pump.controller, from
terminal D to rotor A and terminal C, causing the fuel injection controller motor to run.
As the motor runs, rotor A rotates and, when it reaches its drive position, current flow between terminals
ml
D and C is broken, which stops the motor's operation. Thus, the controller is set at i t s position. .
INJECTION PUMP CONTROL SYSTEM 1~~421
Description (Cont'd)
ENGINE STOP OPERATION
IN J E C T ION PUMP CONTROL UN IT

( D . P . C . rnodu l el
.-
-- -- -
- - - -- .
- - .- - -
-- - - - .. SELSlYlK
When the ignition switch is turned t o "OFF" or when the oil pressure switch turns "ON", the fuel injection
pump control unit will activate. When this happens, current flows in sequence through terminal S, rotor
A and terminal C, causing the controller's motor t o rotate as well as rotor A. As the rotor reaches the stop
position, current flow between terminals S and C is broken and the motor will then stop. The controller is
1-
thus set at its position.
- . INJECTION PUMP CONTROL SYSTEM1 1TMZ J
Wiring Diagram
I 3
FUSIBLE L I N K I G N I T I O N SWITCH
ON o r START
(Main harness)
FUSE BLOCK
@@
--
BATTERY
I N J E C T I O N PUMP
CONTROL U N I T
(D.P.C. module) PRESSURE
SW ITCH
I N J E C T I O N PUMP
CONTROLLER
INJECTION PUMP CONTROL SYSTEM E
l !zl
Trouble-shooting
CASE 1
ENGINE DOES NOT START.
. .
Turn ignition w i t c h to START to ensure that injec-

tion pump control lever moves to START position. Check fuel system, glow plugs, etc.
(Refer to "Control Lever Operation Check".) - -
N.G. -
- -
- -
Check whether connecting rod i s disengaged. hm@CL

d
< Go t o "Injection Pump Controller Check".

. Replace injection pump.controller.
O.K.
Go t o "Injection Pump Control Unit Check" Replace injection pump control unit (D.P.C. module).
to check fuel excess control.
O.K.
I 1
I Check oil pressure switch and harness between

injection pump control unit and oil pressure switch.
- INJECTlON PUMP CONTROL SYSTEM 1 ~ ~ 2 1
CASE 2
ENGINE STARTS BUT SOON STOPS.

I
/ After engine starts (ignition switch ON), ensure \ ,

that injection pump control lever moves to DRIVE
Check fuel system, venturi, e t c
position.
(Refer to "Control Lever Operation Check".)
N.G.
with ignition switch ON, disconnect oil pressure

switch connector to see if-injection pump control Check oil pressure lines and oil pressure switch.
lever-movesto DRIVE position.
I
. . .
N.G.
..
. .
Go to "Injection Pump Controller Check". Replace injection pump controller.
Go to "Injection Pump Control Unit Check" Replace injection pump control unit (D.P.C. module).
to check drive position control.
O.K.
1 1
i
Check short circuit in wiring harness between

injection pump control unit and oil pressure switch.
INJECTION PUMP CONTROL SYSTEM
CASE 3
ENGINE CONTINUES TO RUN WHEN IGNI-

TION SWITCH IS TURNED OFF.
Check whether connecting rod is disengaged. Connect.
O.K.
#
Go t o "Injection Pump Controller Check".

.
Replace injection pump controller.
Go t o "Injection Pump Control Unit Check" Replace injection pump control unit (D.P.C. module).
to check engine stop control.
>
I
Check harness between injection pump controller

and injection pump contr'ol unit.
CASE 4
ENGINE CONTINUES TO RUN IN REVERSE

Dl RECTION.
f
Turn ignition switch off t o see if engine stops. Refer to Case 3 above.
1
+
Disconnect and ground oil pressure switch connektor Check oil pressure switch, oil pressure lines, etc
with a suitable lead wire to see if engine stops.
I
+I N.G.
Go t o "Ignition Pump Control Unit Check" to check Replace injection pump control unit (D.P.C. module).
the operation of the anti-reverse rotation function.
-
O.K.
I Check harness between injection pump control 1

I unit and oil pressure switch.
- . -- -. - - --
INJECTION PUMP CONTROL SYSTEM @!El
1 Injection Pump Control Lever Operation Check
(1) "START" OPERATION
2. Disconnect harness connector from starter motor "S"
terminal.
3. Turn ignition key to "START" in order to ensure that injec-
tian pump control lever moves to the start position.
1 (2) "DRIVE" OPERATION

1 1. Turn ignition switch OFF.
2. Disconnect harness connector from oil pressure switch.
1 3. Turn ignition key to "ON" to ensure that injection pump
control lever moves to the drive position.
I
INJECTION PUMP CONTROL SYSTEM P%l
lnjection Pump Control Lever Operation Check
(Cont'd)
(3)"STOP" OPERATION
1. Turn ignition switch to "OFF" in order to ensure that injec-
tion pump control lever moves to the stop position.
2. Start engine. Disconnect and ground oil pressure switch
connector with a suitable lead wire to see if injection pump
control lever moves to the stop position.
SEL692K
lnjection Pump Controller Check

MOTOR CHECK
2. Disconnect harness connector from injection pump con-
troller.
3. Apply battery voltage between terminals @ and @ .
lnjection pump controller motor should run and control lever
should rotate.
I f injection pump controller does not work, replace controller.
When replacing controller, be sure to disconnect 6-pin harness

connector from injection pump control unit and then reconnect
it after installing controller.
BATTERY
IDC12VI
SEL467E
INJECTION PUMP CONTROL SYSTEM I T~ 2 1
lnjection Pump Controller Check (Cont'd)
LEVER POSITION CONTROL CHECK
Fabricate adapters, as shown in the following illustration, and
connect terminal @ to each of terminals listed in the table
below. Injection pump control lever should stop at correspond-
ing position.
Be careful not to connect lead wire to the wrong terminals as
this will damage injection pump controller.
Connsct terminal Corresponding position of

@ to: injection pump control lever
Terminal @I START
.-
Terminal @ STOP
Terminal (@ OR lV E
BArnRY
(DCl 2V)
SEL460E
lnjection Pump Control Unit (D. P.C. module)

Check
PREPARATION FOR CHECK
2. Disconnect harness connector from starter motor "S"
terminal.
&pin connector
3. Disconnect the 8-pin harness connector from the injection
pump control unit.
4. Connect test lamp between terminals @ and @ of
injection pump control unit.
SE L459E
.- . INJECTION PUMP CONTROL SYSTEM @!El
Injection Pump Control Unit (D.P.C. module)
Check (Cont'd)
ENGINE STOP CONTROL CHECK
3. Connect a suitable lead wire between terminals @ and 0 .
4. When ignition switch is turned to "OFF" from "ON", test
lamp should come on and go off in about 10 to 20 seconds.
5. Disconnect 6-pin connector and then reconnect it.
SEL46OE
- DRIVE POSITION CONTROL CHECK

4. When ignition switch is turned to "ON" from "START", test
lamp should come on and go off in about 10 to 20 seconds.
Oil p-n
mi*
lmltion MtFh ...START - ON
- --
SEL461 E
INJECTION PUMP CONTROL SYSTEM F!?zl
Injection Pump Control Unit (D.P.C. module)
Check (Cont'd)
FUEL EXCESS CONTROL CHECK
2. Disconnect harness connector from oil pressure switch and
ground it with a suitable lead wire.
3. Connect a suitable lead wire between terminals @ andI0 .
4. When ignition switch i s turned to "START", test lamp
should come on and then go off in about 10 to 20 seconds.
milch ...OFF -START
SE L462 E
ANTI-REVERSE ROTATION FUNCTION CHECK

2. Disconnect harness connector from oil pressure switch and
ground it with a suitable lead wire.
4. When ignition switch is turned to "ON" from "START",
test lamp should come on, and then go off in about 10 to
20 seconds.
Trr
1-P
{SAW)
...START + ON
switch
SEL463E
SERVICE DATA AND SPECIFICATIONS (S.D.S.)
General Specifications
I
CARBURETOR (Jet and air bleed size)
Model except Australia and
GuH nandud model Aualb model
Gulf standard models
Carburetor model
MTT ~ r r ~n A ~ T stmrkd ~ropicr~
21538026 21-26 21J-23 211380.24 21J-27 21J36028
Throttle chamber bore m m (in) - P 36 11.421
S 40 (1.57)
P 32 (1261
Venturi diameter mm (in]
S 36 (1.42)
P #I 42
Main jet
s #2% I em 1 #226
P #60
Main air bleed
s nsa
P #54
Slow jet
S #I30
P #I80
Slow air bleed
S W80
Power jet M20 I #a0 I 6124
1
P: Primary S: Secondary #: -mm
100
Main jets for high altitude

E.G.R. CONTROL VALVE
kPa (mbar, mmHg, inHg)
Fully open vacuum Over -14.7 (-147, -1 10, -4.33)
VACUUM MOTOR
kPa (mbar, rnmHg, inHg)
Opening starts -9.6 (-96, -72, -2.83)
Fully open Over -1 9.5 (-195, -1 46, -5.75)
4XloO ~132001 #l26 MOO
Replacement of main jets is not necessary for models equipped with
altitude compensation system.
SERVICE DATA AND SPECIFICATIONS (S.D.S.) I~B42)
Inspection and Adjustment
A.T.C. AIR CLEANER FUEL PUMP
-- Amrogkrricamprmum Fuel pump capacity
'C ( O F 1 mQ(Imp f l oz)lminute More than 2,600 (91.5)
at 1,000 rpm
mouv Above
38 1100) 4%111%) Fuel p r r r ~ n -
25.5 32.4 (0.255 - 0.324,
kPe (bar, kg/cm', pll) -
0 2 6 0.33, 3.7 4.7) -
Below 10.7 (107.80.3.15) a d air Coot air
T.V.V. operation temperature
Above 22.7 (227, 170.6.69) Hotair CboI eir Open "C (OF) 50t3 (122t5.4)
Closed 'C (OF1 30 (861
IDLE COMPENSATOR
Unit: OC (OF)
Idle compensator partially opens -

65 74 (149 - 165) B.C.D.D.
Idle compensator fully owns Above 74 (165) Model except
Australia and Gulf Australia and
Model standard models Gulf standard
models
Mrr A n Mrr
B.C.D.D. set pressure -76.0k0.7

(at sea levell (-760k7, -78.6t0.7 1-786k7,
kPa (mbar, -570k5, -590k5, -23.23i0.20)
mmHg, inHg) -22.44i0.20)
CARBURETOR (Jet and air bleed size)

Model except Australia and
Gulf standard model Australia model
Gulf standard models
Carburetor model '
M/T A n MTT A n Standard Tropical
21J36G25 21536026 21J36G23 21536024 21536027 21J36@28

Choke type Manual choke Automatic choke Manual choke
Fast idle adjustment
Fast idle speed
( A n model in "N" position) rpm 1,1 00i50 900k50 1,100k50 9mi50 1,l m k 5 0
Clearance " A 225+0.15 2.58t0.15 1.3720.1 4 1.64t0.14

mm (in) 225i0.15
(at 2nd cam step) (0.0886 (0.1016 (0.0539 (0.&46
(0.0886*0.0059)
iO.0059) tO.0059) 20.0055) t0.0055)
Vacuum break adjustment mm (in)

Clearance "R, " 3.25*025 (0.1280'-0.0098)
Clearance "R, " 5.0k0.5 (0.197k0.020)
F.I. pot sdjustment

F.I. pot touch speed rpm - 1.700t100 - 1,700k100 -
ldle speed
( A n model in "D" position) rpm 650i50
Idle CO % 1.5
SERVICE DATA AND SPECIFICATIONS (S.D.S.1 b!EI
Inspection and Adjustment (Cont'd)
DISTRIBUTOR
TOT00471
Tme
[MITSUBISHI make]
Firing order 1-5-3-6-2-4
Rotating direction Counterclockwise
Point gap mm linl -

0.45 0.55 (0.018 0.022) -
Cap insulation resistance MR More than 5 0
Rotor head insulation resistance Ma More than 5 0
Cap carbon point length mm (in) More than 3 (0.12) protruded length
Distributor spark advance curve

Set t o O0 at 300 rpm
I$ 1 -
I I I
--c Vacuum -kPa (-mbar, -mmHg, -ink@)
IGNITION COIL
-1549
TW.
[HANGHIM mrko?
P r i m m mimnes
fat wc (ss0FI1
n I 1.m-3.a
SlWdWy rahnra
k.C1 9.0- 13A
[at W C (WFjl
. -
SERVICE DATA AND SPECIFICATIONS (S.D.S.) -
P
- ITD421
In-line Type lnjection Pump
APPLICATION Governor
Destination Part number Pump number Remarks Thickness
- Part number
mm (in)
Without high
16700-06J60 101641-9292 altitude 0.2 (0.008) 1924137504
compensator 0.3 (0.012) 1924137505
General areas 0.5 (0.020) 1924137500
With high Pneumatic governor 1.O (0.039) 1924137501
16700-06J61 101641-9302 altitude spring adjusting shim 1.5 (0.059) 1924137502
compensator 2.0 (0.079) 19241-37503
2.5 (0.098) 1924137506
3.0 (0.1 18) 1924137507
INSPECTION AND ADJUSTMENT 0.1 (0.004) 1922737500

0.2 (0.008) 1922737501
Injection timing Torque control travel
0.3 (0.012) 1922737502
adjusting shim
0.5 (0.020)
Injection timlng
I e.T.0.c. is' 1.O
0.1
(0.039)
(0.004)
1922737503
1922737504
1922937500
0.2 (0.008) 1922937501
Injection pump Torque control spring
0.3 (0.012) 1922937502
adjusting shim
0.5 (0.020) 1922937503
1.O (0.039) 1922937504
Feed pump
W l r d Wear limit
nun (in) mm (in)
Roller to pin clearance 1 I 0.30 1001181
405 mQ (14.3 Imp f l oz) or more

Oil feed rate within 15 seconds at a pump
speed of 1,000 rpm.
Discharge should occur within one

minute (60 seconds) with a pump
Pumping capacity
speed of 100 rpm and intake head
of 1.O meter (3.3 ft).
(pre-stroke: plunger lift
The time required t o develop an oil
feed pressure of 333 t o 412 kPa (3.33
Oil feed pressure to 4.12 bar, 3.4 to 4.2 kg/an2, 48 t o
60 psi) with a feed pump speed of
600 rprn should be within 30 seconds.
Operate the priming pump at a

Pumping capacity rate of 60 to 100 strokes per
(priming pump) minute and verify that pumping
is started within 25 strokes.
Camshaft end play
adjusting shim
SERVICE DATA AND SPECIFICATIONS (S.D.S.) lrw]
In-line Type lnjection Pump (Cont'd)
Timer Fuel filter

Flyweight holder to flange
clearance (Lock plate to
0.02 - 0.10 (0.0008 - 0.0039)
thrust washer clearance) 98 - 137 (0.98 - 1.37,
rnm (in) pressure 1.0- 1.4.14-20)
Thickness
Pan number
rnrn (in)
0.1 (0.004) 1682237500 Injection pump calibration data

0.2 (0.0081 16822-29000
0.3 (0.012) 1682237501 This data will be introduced later.
0.4 (0.016) 16826-99011
Timer spring adjusting 0.5 (0.0201 1682237502
shim 0.6 (0.024) 16822-29001
0.7 (0.028) 1682237506
0.8 (0.03 1 1682237507
0.9 (0.035) 1682237508
1.O (0.039) 16822-29002
-
0.10 (0.00391 1682689007
0.12 (0.0047) 1682889000
0.14 (0.0055) 1682699001
Timer plate bearing 0.1 6 (0.0063) 1682699002
adjusting shim 0.1 8 (0.0071 1 1682689003
0.20 (0.00791 16826-99005
0.30 (0.01 18) 1682699006
0.50 (0.0197) 16826-99004
SERVICE DATA AND SPECIFICATIONS (S.D.S.) ITMZ 1
VE-Type lnjection Pump
APPLICATION
Dimension "K" mm (in! 3.2 - 3.4 (0.126 - 0.134)
Destination Part No. Pump No. Remarks
Australia I 167OMlglO2 I 104760.4021 1 Mil without

exhaust brake
INSPECTION AND ADJUSTMENT

Injection timing
Plunger lift mm (in)

I 0.74t0.02 ~0.0291rO.0008~
(equivalent to 6' B.T.D.C.1 "K4'
SE Fa39
Adjusting shim ("B" position)
Thickness
Pan number Part number
mm (in, mm (in1
16884-V0700 1.92 (0.0756) 16742-RE100 1.96 (0.0772)

16884\/0701 2.00 (0.0787) 16742-RE101 2.04 (0.0803)
16884V0702 2.08 (0.0819) 16742-RE102 2.12 (0.0835)
16884-V0703 2.16 (0.0850) 16742-RE103 2.20 (0.0866) -
16884V0704 2.24 (0.0882) 16742-R8104 2.28 (0.0898)
16884-V0705 2.32 (0.0913) 16742-RE105 2.36 (0.0929)
16884~0706 2.40 (0.09451 16742-RE106 2.44 (0.0961
16884-V0707 2.48 (0.09761 16742-RE107 2.52 (0.0992)
16884-VO708 . 2.56 (0.1008) 16742-RE108 2.60 (0.10241
16884-V0709 2.64 (0.1039) 16742-RE109 2.68 (0.1055)
16884-V0710 2.72 (0.1071) 16742-R8110 2.76 (0.10871
16884-V0711 2.80 (0.1 1021 16742-RE111 2.84 (0.1118)
Use of adjustment value and adjusting shim 16884-V0712 2.88 (0.1 134)
when installing injection pump.
Dimension "KF" mm (in1 6.5 - 6.7 (0.256 - 0.2641 Diemnsion "L" mm (in) 1.5 - 2.0 10.059 - 0.079)
"L"
- -
Adjusting shim ("A" position)
Part number Thickness mm (in)

SERVICE DATA AND SPECIFICATIONS (S.D.S.) E!sl
VE-Type lnjection Pump (Cont'd)
'Iw Of
mrn (in) 0.1 5 - 0.35 (0.0059 - 0.0138)
Dimension "MS' mm (in) 0.9 - 1.1 (0.035 - 0.043)
holder "L"
Tension lever - .. ------
Collec
lever
5 1starter lever
Adjustins cloning plug

Adjusting shim
Part number Length mm (in)
Part number Thickness mm (in)
16268-R8100 3.10 (0.1220)
19208-V0700 1.05 (0.04131
16268-R8101 3.30 (0.1299)
19208-VO701 1.25 (0.0492)
16268-R8102 3.50 (0.1378)
19208-V0702 1.45 (0.0571
16268-R8103 3.70 (0.1457)
19208-VO703 1.65 (0.0650)
16268-R8104 3.90 (0.1 535)
19208-VO704 1.85 (0.0728)
16268-R8105 4.10 (0.1614)
16268-R8106 4.30 (0.1693)
16268-R8107 4.50 (0.1 772)
Injection pump calibration data

This data will be introduced later.

Efaeci: Engine Fuel Emission Control System

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Efaeci: Engine Fuel Emission Control System

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Efaeci: Engine Fuel Emission Control System

Uploaded by

Copyright:

Available Formats

ENGINE FUEL &

EMISSION CONTROL SYSTEM

I I TB42 & TD42 1 J

1612562SOO Checking fuel level

Delivery valve extractor

Disassembling and assembling tools

Socket wrench for

"K" & "KF"

Adjusting device on pump tester

SPECIAL SERVICE TOOLS

Destination Model except

Automatic temperature Temperature sensor

Fast idle pot

X: Available -: Not available opt: Optional

F.I. pot or F.I. actuator

1-- - ,-+-- ----------

Air Temperature Sensor

E.G.R. Control Valve

Water ternmature Therrrur! vacuum E.G.R. system

Below 40 (104) Not activated

B.C.D.D. (Boost Controlled Deceleration Device)

B.C.D.D. Control Solenoid Valve

Fuel Cut Solenoid Valve

purge orifice 0 : Air

Secondary small venturi

(0) : N-rn (kg-rn, ft-lb)

Acderatlng pump lever

Accelerating pump plston

Thmttle adjusting screw

Accelerating pump piston

,-Secondary main air bleed

B.C.D.D. control solmoid

With air conditioner

Throttle adjusting screw

(0.5 - 09.3.6 - 661

Secondary main air bl-

maln air bleed

: N.m (kg-rn. ft-lb)

Slow economizer bleed

Step system Accelerating pump system Power valve system

- 1I \ Llnlet check valve

CLEANING AND INSPECTION

Disconnect ignition wire between

I Disconnect fuel cut solenoid

I while cranking engine for

5. Lower float slowly until float stopper contacts carburetor,

If necessary, use Tool to visually check fuel level as follows:

3. Make sure bimetal cover index mark is aligned with the

AUTOMATIC CHOKE HEATER

AUTOMATIC CHOKE RELAY

3. If out of specification, remove carburetor and make fast idle

Fast ldle (Manual Choke Model)

Connecting link bend to

3. Lightly push piston rod in the direction that closes choke

4. Lightly push piston rod toward diaphragm and check clear-

Model excrpt Australia M/T and

3. If no sound is heard from fuel cut solenoid valve, replace

2) Remove fuel cut solenoid valve from carburetor.