Warren Pumps

FSXA 2300 Series

Heavy-Duty, High Pressure Screw Pumps

Two-Screw Team
FSXA 2300 Series
Heavy-Duty, High Pressure Screw Pumps
• Capacities to 3500 GPM+
• Discharge pressures to 1400 PSI
• Viscosities from .5 cst
Permanently Timed Back Pull Out
Factory performed timing is easily repeated Rotor removes for inspection or repair without
with Warren’s method of gear and screw disturbing piping or driver. One-craft
Advantages synchronization. maintenance.
• Very high efficiencies
• Rugged body and rotor design
• Excellent performance on both
low and high viscosity fluids
(.05 – 10,000 cst)
• Double helical timing gears
minimize rotor wear by maintaining
axial alignment, and also provide torque
load capacities
• Long service intervals

Applications
• Crude Oil Pipelines or Platforms –
transfer and gathering
• Gas Turbine Fuel Pumps or
Burner Feed Pumps – fuel oils
and naphtha
• Petroleum Transport – barge and
tanker loading/unloading, tank
farms
Bearings
Options Radial loading is handled by heavy-duty roller
• Iron or Cast Steel Casing bearings at five locations that are sized to
• Chrome Plated Bores handle maximum loads. They are oil
• Hard Fused Coating on Rotors lubricated and are sealed off from the
pumpage by internal mechanical seals, which
• Hardened Timing Gears
are under suction pressure only. The heavy-
• External Seal Lubrication duty double row thrust bearing locks the drive
• General Compliance with API676 shaft in position axially. This is one of the only
six bearing twin screw pump designs in the
world and is a result of more than 50 years
of experience in high pressure applications.

Hardened Steel
Double Helical Timing Gears
Hardened steel double helical timing gears are used to
prevent metal-to-metal contact between the meshed rotating
screws. The clearance between the pumping screws results in
longer pump life and higher average efficiencies over the life
of the pump.

The double helical concept allows for multiple tooth

engagement and maintains precision screw clearances.
Typical crude oil pipeline pump with Both are features that commonly used spur-type gears cannot
natural gas engine drive. provide.
Body
The solid cast body is generously ribbed and has thick cross
sections for pipeline pressures and rigidity. The suction flow
passage is designed to provide a constant area from the flange
opening to the screw entrance allowing for the best NPSH
capabilities of any similarly sized pump.

Wear Protection
To insure long life in tough services, the critical pumping
surfaces are coated. The body bore can be coated with an
electrolytically applied industrial hard chrome. The screws
can have a variety of OD coatings with hardness in excess of
60 (Rockwell C). Nitriding and other coating combinations
are added features that, when combined with the chrome
lined bore, have proven to be the best wear protection in the
industry.

Integral Screw and Shaft

Each rotor is of an integral design, meaning that the entire
screw and shaft is machined out of one piece of material,
allowing for maximum rigidity and stiffness. This minimizes
shaft deflection, an important consideration in high-pressure
pumps.

High Efficiency Screw Profile

Having mastered the manufacture of pumping screws, the 2300
Series can come in a variety of screw pitches, and combined
with the “QNS” screw profile offers the highest efficiency twin
screw pump in the industry. This has been accomplished as a
result of over 50 years of factory testing and field performance.
FSXA Quick Selection Chart
0 10 20 30 40 50 60 70 80 90
4000
LEGEND 15000
bard
14000

Contact Warren 3500

13000

12000

3000
FSXA-3830 11000

10000
2500
FSXA-2530 9000
Capacity (gpm)

8000
2000

FSXA-2030 7000

6000
1500

5000
FSXA-1250

4000
1000

3000
FSXA-655

500 2000

1000
FSXA-360

0 0
0 200 400 600 800 1000 1200 1400
Differential Pressure (psid)
Approximate Dimensions
FSXA MOTOR
PUMP SUCTION DISCH. HP RPM FRAME C CP HA HB HC HD HG HL HM HO HT X Y Z HL1 PH DH W
SIZE
360* 21/2” - 300# 2” - 600# 100 1750 405TS 351/8” 377/16” 21” 601/4” 779/16” 131/2” 3” 171/2” 241/4” 171/2” 5” 11/2” 51/2” 33/4” 265/8” 101/2” * N/A
655* 4” - 300# 3” - 600# 200 1750 447TS 43 /8” 47 /4”
7 3
23” 74 /4” 96 /8” 15 /2”
1 5 1
4” 23 /16” 27 /16” 20 /4”
5 9 1
5” 1 /8”
7
6 /4”
3
5” 349/16” 111/2” * N/A
1250 6” - 300# 4” - 600# 250 1750 447TS 437/8” 551/4” 23” 961/2” 1041/8” 17” 4” 245/8” 291/16” 23” 5” 21/4” 83/4” 61/4” 377/8” 13” * 1
/16”
2030 8” - 300# 6” - 600# 400 1750 5010S 583/4” 6315/16” 26” 122” 12711/16” 211/2” 6” 283/8” 365/16” 28” 5” 25/8” 91/2” 71/2” 431/2” 151/2” * 13/16”
2530 10” - 300# 8” - 600# 600 1150 6809L 751/2” 78” 34” 1501/2” 1581/2” 241/2” 6” 341/4” 431/2” 325/8” 5” 33/8” 113/8” 83/4” 531/2” 181/2” * 113/16”
3830 12” - 300# 10” - 600# 1000 1150 6811L 85 /2” 87 /8”
1 1
34” 166 /8” 177 /8” 29 /2”
3 5 1
8” 40” 48 /2” 38 /2”
1 1
5” 3 /4”
3
12 /2” 10 /4” 62”
1 1
21 /2”
1
* 57/16”
* Pump Size #360 & #655 do not have Gear Housing Foot. Dimensions not to be used for construction purposes. * To be determined by customer.
CL PUMP

CLMOTOR & BASE

DISCHARGE HC
FLANGE
X HL CP C
HT
CLEARANCE HL1
REQUIRED FOR
REMOVAL OF ROTOR SUCTION
FLANGE

HO

Z HM
DH
PH
HD
W

Y HG

HA HB

Allweiler Houttuin IMO Pump Warren Pumps Warren Pumps Inc. • 82 Bridges Ave. • PO Box 969 • Warren, MA 01083-0969 USA
Ph. 413-436-7711 • Fax 413-436-5605 • www.warrenpumps.com • email: warrensales@colfaxcorp.com WP 4/02 5M