Blackhawk Pump Manual 2018

Maintenance and Operations Manual
Version 1.8a
Copyright 2015, BlackHawk Industrial, 1501 SW Expressway DR., Broken Arrow, OK.74012.
BlackHawk Industrial excludes warranties expressed or implied, as to the accuracy of the data and
other information set forth in this publication and does not assume liability for any losses or
damage resulting from the use of the materials or application of the data discussed in this
publication. BlackHawk Industrial make no warranty, either expressed or implied, other than those
stated in its standard Terms and Conditions of Sale (available on request.)
2
Index
Introduction
Specific Models and Pump Curves……. Section 1
Operation……………………………………….. Section 2
o Before Operation
o Coupling Alignment
o Mounting Hydraulic Motor Adapter
o Changing Discharge Nozzle Orientation
o Pump Startup
Suggested Piping
Pump Startup
o General Operation
Records
Lubrication
o During Operation
Maximum Speed
Operation Guidelines
Lip Seal Lubrication
Mechanical Seal
o After Operation
Maintenance………………………………….. Section 3
o Disassembling the pump
o Reassembly
o Installing Shaft Lip Seals
o Setting Impeller Clearances
o Installing Packing
o Installing Mechanical Seal
o Seal Lubricants and Suggested Service Ratings
3
Troubleshooting……………………………. Section 4
Parts Breakdowns…………………………. Section 5
o 350.205 Size 4x4x12
o 350.205 11.25 Size 4x4x12-11.25
o 350.2056 Size 4x4x12 Hylar Coated
o 350.1241 Size 6x5x10 Mechanical Seal
o 350.1242 Size 6x5x10 Lip Seal
o 350.1243 Size 6x5x11 Mechanical Seal
o 350.1244 Size 6x5x11 Lip Seal
o 350.202 Size 8x6x14 Lip Seal (100 HP Frame)
o 350.2016 Power End Assembly (100 HP Frame)
o 350.201 Size 8x6x14 Packed (300 HP Frame)
o 350.203 Size 8x6x14 Lip Seal (300 HP Small Frame)
o Legacy to SAP Number Crossover List
o SAP Number to Legacy Crossover List
Special Tools…….…………………………. Section 6

Addendums…………………………………. Section 7
o Oil Lube Mechanical Seals
o Oil Lube Power Frame Bearing
o Close Coupled Electric Motor Versions
Notes …………………………………………... Section 8
4
Section 1
Introduction
This manual covers Duncan Industrial Solutions models 350.205,
350.2056, 350.1241, 350.1242, 350.1243, 350.1244, 350.202, 350.203
5
Model 350.205 4x4x12-12
Buna-N Lip Seals
6
Model
Model350.1241
350.20566x5x11-10
4x4x12-12
Mechanical Seal Teflon Seals
Halar Impeller,
7
Model 350.1241 6x5x11-10
Mechanical Seal
8
Model 350.1242 6x5x11-10
Buna-N Lip Seals
9
Model 350.1243 6x5x11-11
Mechanical Seal
10
Model 350.1244 6x5x11-11
Buna-N Lip Seals
11
Model 350.202 8x6x14-14
Buna-N Lip seals
*Contact BlackHawk Pumps& Services for applications in excess of 100 HP.
12
Model 350.203 8x6x14-14
Buna-N Lip seals
13
Model 350.2016 Support Frame
14
Section 2
Operation
Warning: Failure to follow the operating instruction warnings of hazards or unsafe
practices could result in injury or death.
Warning: Before attempting to service the pump…..

1. Review the manual.
2. Disconnect or Lock Out all power to the pump to make sure the pump cannot be operated.
3. Close suction and discharge valves.
4. Check the pump temperature to make sure fluid has not overheated.
5. Vent the pump slowly.
6. Drain the pump.
Warning:
Do not attempt to pump volatile, corrosive, or flammable materials without reviewing the
application with the manufacturer. Misapplication could damage the pump or endanger personnel
as a result of pump failure.
Warning:
DO NOT OPERATE THE PUMP UNLESS ALL GUARDS ARE IN PLACE. Exposed rotating
parts can catch clothing, fingers or tools causing severe injury.
Warning:
Do not run pump against a closed discharge for long periods of time. Doing so will
cause pump components to deteriorate and could cause the fluid to boil, build
pressure, and cause the casing to rupture.
Warning:
Use lifting equipment that’s in good operating condition and with adequate capacity
to prevent injuries to personnel or damage to equipment.
15
Before Operation
The pump was inspected and tested before shipment from the factory. Before
installation, inspect pump for which may have occurred during shipping such as:
1. Dents, cracks, damaged threads, etc.
2. Carefully read all warning labels.
DANGER: Make sure all power sources are OFF and Locked Out before performing
any service to the pump.
WARNING: BEFORE STARTING PUMP

Disconnect and remove coupling and briefly start motor to verify proper direction of
rotation. Operation in the wrong rotation will cause severe damage to the pump.
Rotation should be as follows:
All Pumps are Right-Hand Rotation Units –

CLOCKWISE when viewed from pump shaft end
COUNTERCLOCKWISE when viewed from the
suction flange.
If rotation is in the wrong direction, shut off and lock out the power and switch any
TWO legs of the three-phase circuit. This should correct the rotation.
If your pump is single phase unit, shut off and lock out the power and re-connect
motor leads as indicated by the diagram inside the motor’s junction box.
If the pump is power take off, engine, or hydraulic driven, consult your system
designer.
Once the proper direction of rotation has been established and the piping has been
connected it will be necessary to realign the pump and motor. (This is due to shifting
during shipment and loads imposed on the pump by the piping system.)
FAILURE TO PERFORM THE ABOVE WILL VOID

THE WARRANTY!
16
Coupling Alignment
1. Check parallel alignment by placing a
straightedge across the two coupling
flanges and measuring the maximum offset at various points around the periphery
of the coupling without rotating the coupling (see Figure 1). If the maximum offset
exceeds the figure shown under "Parallel" in Figure 3, realign the shafts.
2. Check angular alignment with a micrometer, vernier, or caliper. Refer to X and
X(max) dimensions in Figure 2. Measure from the outside of one flange to the
outside of the other at intervals around the periphery of the coupling. Determine
the maximum and minimum dimensions without rotating the coupling. These
measurements must be within the range of X and X(max). If a correction is
necessary, be sure to recheck the parallel alignment.
(Figure 1) Parallel (Figure 2) Angular
Maximum RPM and Allowable Misalignment - Inch

Types JE, JN, E & N EPDM Type H Hytrel
Sleeve Maximum
Size RPM Parallel Angular X1 X(max) Parallel Angular X
3 9200 0.01 0.035 1.188 1.223 -- -- --
4 7600 0.01 0.043 1.5 1.543 -- -- --
5 7600 0.015 0.056 1.938 1.994 -- -- --
6 6000 0.015 0.07 2.438 2.508 0.01 0.016 2.5
7 5250 0.02 0.081 2.563 2.644 0.012 0.02 2.625
8 4500 0.02 0.094 2.938 3.032 0.015 0.025 3
9 3750 0.025 0.109 3.5 3.609 0.017 0.028 3.562
10 3600 0.025 0.128 4.063 4.191 0.02 0.032 4.125
11 3600 0.032 0.151 4.875 5.026 0.022 0.037 4.938
12 2800 0.032 0.175 5.688 5.863 0.025 0.042 5.75
13 2400 0.04 0.195 6.625 6.82 0.03 0.05 6.688
14 2200 0.045 0.242 7.75 7.992 0.035 0.06 7.812
16 1500 0.062 0.33 10.25 10.58 -- -- --
(Figure 3)
17
Mounting the Hydraulic Motor Adapter
There are two hydraulic motor adapters available for use with the 350.2016 power
frame. The process of mounting the adapter is similar for either model. Figure 2 shows the
278.89831 adapter assembly.
(Legacy 278.89831) Cast Iron hydraulic motor mount.
(104913-46432-247) Steel hydraulic motor mount.
Figure 1 Figure 2
1. Mount the motor adapter (Item 1) to the integral mounting flange on the 350.2016
power frame. Make sure the piloted faces are aligned correctly. (Note: paint may
need to be lightly sanded to insure a square fit).
2. Install 4-each 1/2NCx1-1/4” Grade 5 cap screws and lock washers (Items 3 & 4)
through integral flange on the power frame and into the motor adapter (Item 1).
Tighten securely.
3. Clean pump shaft. Slide 1-7/8” bore coupling half (Item 6) over shaft. DO NOT
tighten set screw at this time.
4. Install Hytrel coupling sleeve and motor side coupling on pump side coupling.
5. Install the motor bracket (Item 2) to the hydraulic motor using 1/2NCx1-1/4” Grade
5 cap screws and lock washers (Items 3 & 4).
6. Install hydraulic motor and flange assembly into motor coupling half that’s already
mounted on the shaft.
7. Adjust coupling so that a gap of 1.12” is held between the coupling flange faces.
8. First tighten set screws on shaft to 20 – 23 ft.lbs. Then tighten set screw over key to
20 – 23 ft. lbs.
18
Changing Pump Discharge Orientation
The pump discharge can be easily rotated in 45 degree increments to match piping.
This is accomplished removing the mounting feet and moving them to a different position
on the pump frame. This avoids removing the pump casing and having to reset impeller
clearances. Front and rear feet can even be placed different positions if required.
19
Pump Startup
Suggested Piping –
1. Pump
2. Eccentric Reducer
3. Suction Valve
4. Foot Valve
5. Discharge Valve
6. Suction Pressure Gauge
7. Discharge Pressure Gauge
Suction piping should

extend a minimum of
5 times the suction
diameter from the first
elbow.
Suction pipe size should never be any smaller than pump suction pipe size.
Suction valve should always remain fully open when pump is operating.
Never operate the pump against a closed discharge valve for extended periods of time.
Never use pump to support piping or force misaligned piping into place.
Suction line should be designed to avoid air pockets.
The suction line should always slope downhill away from pump.
Priming the Pump –

1. Open pump suction valve.
2. Vent air from pump and fill with liquid so that fluid covers the eye of the impeller.
3. Start pump and partially open discharge valve.
4. Slowly open discharge valve as discharge pressure stabilizes.
5. If pump fails to prime, shut down pump and repeat steps 1 thru 4.
6. If the pump still fails to prime, shut down pump and inspect for air leaks in the
suction line.
7. DO NOT RUN PUMP DRY or with insufficient prime. Catastrophic damage to the
mechanical seal or shaft lip seals will occur.
20
General Operation
Pump Records – Records of the pump data should be maintained whenever possible.
These should include:
1. Pump serial number.
2. Pump model number and impeller diameter.
3. Pump shaft seal type.
Lubrication –
Bearings - Bearings are grease lubed. They should be lubricated with 4-5 shots of
grease after every 12 hours of operation or 5 jobs. The following NLGI2 grease types
are approved for use in the pump bearings.
1. Chevron Ulti-Plex Synthetic Grease EP
2. Castrol Optipit
3. Mystic JT6 Hi-Temp #2
4. Lubrication Engineers Almaplex # 1275
Stuffing Box Lip Seals – Stuffing box lip seals are flushed with pressurized oil at no
greater than 5 – 7 psig. Seals should be flushed with Dexron III / Mercon automatic
transmission fluid.
Environmental Conditions – before operating the pump make sure the following
conditions are met:
The pump contains liquid that is above the freezing point.
Pump suction and discharge valves are open.
During Operation
Maximum Pump Speed – The maximum recommended speeds for the pump are:
Model 350.205, 350.2056 - 2600 RPM
1.375
Model 350.1241, 350.1242, 350.1243, 350.1244 – 1800 RPM 6.000
Model 350.201, 350.202, 350.203 – 1800 RPM

this pump speed is exceeded, bearings may overheat and fail
prematurely. Maximum bearing temperature (measured at the
test points on bearing frame) should not exceed 220 deg. F. 8-350.12432
(Please consult manufacturer if these speeds need to be

exceeded.)
Operating Guidelines for the Pump –

DO NOT operate the pump dry. Temperature Test Point
DO NOT operate the pump with the suction valve closed.
DO NOT operate the pump with the discharge valve closed for more than 1 minute.
If the pump must be throttled, use a discharge valve or restriction. NEVER throttle
with a suction restriction or the suction valve.
DO NOT operate the pump in reverse. Severe damage to the pump will occur.
21
Stuffing Box Lip Seals – Stuffing box lip seals are flushed with pressurized oil at no greater
than 5 – 7 psig. Seals should be flushed with Dexron III / Mercon automatic transmission
fluid. Fluid is supplied by either air pressurized oil supply tank (Legacy part #277.02161 or
HP 30034 seal tank) or electric circulating pump system (part # HP 31007).
Mechanical Seals –
The mechanical seal uses the process fluid for lubrication. DO NOT allow the
mechanical seal to run dry or mechanical seal failure will occur.
After Operation
DO NOT close the suction valve while pump is connected to a source of possible
high pressure. Pumps are rated for a maximum of 150 PSIG.
If slurry has been pumped, wash out the pump with water for several minutes while
pumping at a high rate. If the pump speed can be changed, rapidly accelerate and
decelerate the pump from near zero rpm to maximum rpm while washing out.
If the slurry was cement, perform the previous process immediately. If this is not
possible, pump other liquids through the pump until it can be thoroughly washed
with clean liquids. Failure to flush the pump will allow the cement to solidify inside
the pump.
If the pump will be exposed to freezing temperatures before it is used again,
remove the drain plugs and empty all liquids from the casing.
22
Section 3
Maintenance
Warning:
Use lifting equipment that’s in good operating condition and with adequate capacity
to prevent injuries to personnel or damage to equipment.
Warning:
Always use personal protective equipment like safety glasses to prevent eye injuries
while performing any service work.
Disassembling the Pump

1. Mount pump securely to work bench by the
rear mounting foot. Fig. 1
2. Attach lifting bail to pump discharge flange

and use appropriate lifting equipment to
support pump casing (Fig 1).
3. Remove retaining nuts (70.32916) and jam

nuts (70.32992) from backside of casing.
Remove casing from rotating assembly while
supporting casing with appropriate lifting Fig. 1
equipment.
4. Place shaft wrench over pump shaft (Fig. 3)

and remove impeller by turning counter
clockwise, allowing wrench to strike table
(Fig. 2).
Fig. 2 Fig. 3
5. Remove the 4 cap screws that (70.43897)
hold the stuffing box (350.12412) in place.
Carefully remove stuffing box while allowing
power frame to be supported by front
mounting foot (Fig. 4).
Fig. 4
23
Fig. 5
6. Remove shaft sleeve (Fig. 5).
7. Remove inboard bearing cap (350.12421)

and shaft slinger (350.12434) (Fig 6).
8. Place rotating assembly face down and

remove rear bearing housing retaining
bolts.
9. Lift rear bearing housing, bearings and

shaft from frame (Fig 7). Fig. 6 Fig. 7
10. Remove rear bearing cap (350.12419).
11. Remove bearing retaining lock nut

(70.09091) (Fig. 8). Fig. 8
12. Use a bearing press to remove bearings

(Fig. 9).
Fig. 9
24
Assembling the Pump
1. Press rear thrust bearings (70.04136) on
shaft in a “back to back” configuration.
(Fig. 10, Fig. 11) Bearings can also be
installed using a bearing heater or they
can be driven on using the appropriate
driver.
Fig. 10
Fig. 11
2. Install lock washer (70.09111) and

lock nut (70.09091) (Fig. 12). Torque lock
nut to 90 ft. lbs. Bend tab on lock washer
to lock nut in position.
Fig. 12
3. Install lip seal (70.80606) into rear bearing
cap (350.12419) using appropriate seal
driver. Lip on seal should face towards
outside. Install 45 deg. grease zerk
(70.22931) in bearing cap. Install O-Ring
(8.33988) around rear bearing cap.
(Fig. 13).
4. Install shaft and bearing assembly in rear

bearing housing (350.12418) (Fig. 14) Fig. 13
5. Slide rear bearing cap assembly

(350.12419) over shaft and bolt to rear
bearing housing using 3/8-16 x 1 hex cap
screw, flat washer and lock washer (Fig.
15).
Fig. 14 Fig. 15
25
6. Install bearing housing O-ring
(70.80612) over bearing housing
(350.12418) (Fig. 16)
7. Install inboard bearing (70.80602) on

threaded end of shaft. Bearing can be Fig. 16
installed facing either direction. Use
appropriate driver or press (Fig 16).
8. Carefully lower shaft and bearing

assembly into frame. Care should be
taken to keep shaft and bearings aligned
with frame so they don't jam (Fig. 17).
9. Install 1/2"-13 jam nut (70.32989) on

1/2-13NC x 1-1/2" bolt (70.43868).
Fig. 16 Fig. 17
Install in threaded hole in bearing
housing. Remove guide pin. Install 1/2-
13NC x 2" bolt (70.43872) thru same
hole in bearing housing and into
threaded hole in frame. Make sure
bearing housing is bottomed out on
frame (Fig. 18).
10. Install lip seal (70.80604) with lip facing

Fig. 18
in, on the back side of the bearing cap
(350.12421) with appropriate seal driver
(Fig. 19)
11. Install lip seal (70.80603), with lip facing

out, in the front bearing cap (350.12421)
with appropriate seal driver. Install
Fig. 19
grease zerk (70.22931) in 1/8" NPT hole
so that connection faces out. Install
(70.22933) grease zerk by driving into
Fig. 20
small hole on opposite side with small
hammer (Fig. 20).
12. Lift power frame assembly and with

hoist and place on assembly table
(Fig. 21).
Fig. 21
26
13. Before detaching hoist, place front
mounting foot (350.12422) underneath
power frame assembly with foot facing
toward back of frame. Slide bolt through
foot and frame to hold in position. The
hoist can now be removed from power
frame (Fig. 22).
14. Install front bearing cap assembly over

Fig. 22
shaft making sure not to damage lip seals
using 3/8"-16NC x 1-1/4 cap screw
(70.43816), washer (70.58806), and lock
washer (Fig. 23).
Fig. 22
15. Install shaft slinger (70.80603) on shaft . DO
NOT lubricate shaft or slinger to facilitate
installation. Flat side of slinger faces the
bearing cap. Leave a gap of about 1/16" to
1/8" off bearing cap (Fig 23).
16. Install shaft sleeve O-ring (70.80609), over

shaft and slide to first step in shaft. Fig. 23
Carefully slide shaft sleeve (350.12435)
over shaft so it seats on O-ring (70.80609)
(Fig 24).
Fig. 24
27
Installing Shaft Lip
Fig. 25 Fig. 26
Seals
17. Install three Buna-N lip seals
(70.80607) with lips facing the
bottom of the stuffing box using
appropriate seal driver (Fig. 25)
18. Install lantern ring set (350.15293)

(Fig. 26).
19. Install one Buna-N lip seal

Fig. 27 Fig. 28
(350.80607) with lip facing bottom
of stuffing box using appropriate
seal driver. Hand pack with grease
working grease into seals and
lantern ring (Fig. 27).
20. Install ring gland (350.12427) with

tapped holes facing up (Fig. 28).
21. Install gland plate (350.12429) using

socket head cap screws (70.43374)
(Fig. 29). Fig. 29 Fig. 30
22. Tighten cap screws (70.43374)

finger tight or torque to 100 in. oz.
DO NOT OVER TIGHTEN OR SEALS
WILL RUN TOO TIGHT ON SHAFT
AND FAIL PREMATURELY (Fig. 30).
23. Install 1/8" pipe plugs (26.1) using

Teflon sealant in top and bottom
1/8" NPT holes in stuffing box.
Install 45 deg. hose adapter (70.96714)
in 1/8" NPT hole in stuffing box 180
deg. apart using Teflon sealant. Hand
tighten cap (70.77872) onto hose
adapter (Fig. 31).
Fig. 31
28
24. Carefully install stuffing box assembly over
shaft , making sure to avoid damaging lip
seals. Slide assembly onto shaft until it seats
in the pilot dimension on power frame (Fig.
32).
25. Install one each 5/8-11NC x 1-3/4" cap

screw (70.43897) and 5/8 lock washer Fig. 32
(70.58962) to hold stuffing box in position.
Make sure stuffing box assembly is
supported by pilot dimension on frame and NOT the lip
seals. Lip seals can be damaged if the weight of the Fig. 33
stuffing box is allowed hang on them. (Fig. 34).
26. Install balance of four each 5/8-11NC x 1-3/4" cap

screws and 5/8 lock washers through pump frame into
stuffing box and tighten.
Use 3 each 5/8-11NC x 2" cap screws (70.43924) and
5/8 lock washer (70.58962) for bottom three holes that
attach the foot (350.12422) to the frame.
27. Install O-ring (70.34019) in groove in stuffing box

(350.12412). Spray with WD-40 to facilitate
installation of pump casing (Fig. 34).
28. Coat O-ring grove with Never-Seize or grease

and install impeller O-ring (70.80608) in O-ring
groove on back side of impeller (350.12414,
350.12431, 350.20501). Never-Seize or grease
will hold o-ring in place during impeller
installation (Fig. 35 ). Fig. 34
29. Install shaft wrench over keyed end of shaft.

Apply never-seize to shaft threads and thread Fig. 35
impeller clockwise onto shaft. Make sure
bearing housing is bottomed out on frame so
shaft extends completely through stuffing box.
29
Setting Impeller Clearances
30. Using shaft wrench as a stop , spin impeller
clockwise allowing wrench to strike the work
table. Repeat this process several times until
impeller is completely seated on shaft (Fig. 36).
(Optional impeller wrench can be used to
tighten impeller to 400 Ft. Lbs. See Section 6)
31. Adjust clearance behind impeller using .014

inch feeler gauge. Use jacking bolts and
retaining bolts on rear bearing housing to
Fig. 36
move impeller in or out. Using .014" feeler
gauge check clearance behind impeller by
cranking shaft to get a .014" average. Make
adjustments as necessary (Fig. 37).
32. Carefully tighten lock nuts on bearing housing

jacking bolts to avoid making changes to
impeller clearances (Fig. 38).
33. Using lifting eye and hoist position pump

casing (350. 12413 or 350. 20502) over Fig. 37
impeller and stuffing box. Carefully push casing
over stuffing box . Be careful not to damage
stuffing box O-ring.
Fig. 38
34. Install 3/4-10NC x 3" cup point set screws
(70.80613) through the unthreaded holes in
the 12:00, 3:00, 6:00, 9:00 positions on the
frame and into the pump casing. Set screws
should extend 2.00 to 2.25 inches from back of
pump casing. Coat threads with Never-Seize
before installing. Install 3/4-10NC nut
(70.32916) on each 3/4-10NC x 3" cap screw .
Leave nut loose at this time (Fig. 39).
Fig. 39
35. Install 3/4-10NC x 2" cup point set screws
(70.80614) through the threaded holes in the
1:00, 5:00, 7:00, 11:00 positions on the frame
and into the pump casing. Coat threads with
Never-Seize before installing. Do not screw
past the frame flange at this time.
30
36. Install 3/4-10NC jam nut Fig. 40 Fig. 41
(70.32992) on each 3/4-10NC x 2"
cap screw. Leave jam nut loose at
this time (Fig. 40).
37. Install lifting strap (Fig. 41).
38. Using .016 inch feeler gauge, adjust

casing in or out to get an average of
.016" clearance between impeller
and suction. Use 3/4-10NC x 2"
(70.80614) set screws to push
casing out and 3/4-10 nuts
(70.32992) to pull casing back.
Once an average of .016" is
achieved, tighten jam nuts
(70.32992) (Fig. 42).
Fig. 42
Installing Packing
1. Packing (350.12438) can be used as an alternative to
the oil lubricated lips seals.
2. Packing can be cut in the field by firmly wrapping
around the shaft sleeve as shown in (Fig. 1).
3. Rings can then be cut at a 90 deg. angle parallel with
the shaft and sleeve (Fig. 2).
4. Individual rings are then installed in the same squence
as the lip seals.
5. Be sure to install the lantern ring in the correct location
6. When installing the individual rings they should be
staggered 90 deg from the previous ring so as to avoid
creating a leak path (Fig. 3).
7. Install gland rings and gland plate finger tight. DO NOT
OVER TIGHTEN.
8. When starting pump allow packing to leak freely. Slowly
tighten the gland bolts until the leak has decreased to
approximately 10 – 12 drops per minute.
9. Always allow some leakage from the packing. NEVER
STOP LEAKAGE ENTIRELY or damage to the shaft sleeve
will occur.
10. Packing should be lubricated with approved grease every 12 operating hours.
31
Installing the Mechanical Seal
1. A mechanical seal is standard on the models
350.1241 and 350.1243. It is available as an
option for all other models except the model
350.201.
2. The process fluid lubricates the mechanical seal,

so no external lubrication is required.
3. Install 70.81033 roll pin thru the small hole at

the bottom of the seal cavity. It should extend
3/32” into the seal cavity (Fig. 2, 3 & 4.)
Fig. 1
Fig. 3 Fig. 4
Fig. 2
4. Install the stationary side of the mechanical into the bore of the seal cavity.
CAUTION: make sure the notch in the back side of the stationary seal is aligned
with the roll pin. Use a soapy water or alcohol hand sanitizing solution to aid in
installtion. Use the cardboard divider supplied with the new seal (to protect the seal
face), press the stationary seal face into the bore until it bottoms out and the o-ring
is seated.
5. Turn seal head over and install 1 each ring of packing (350.12438) in the bottom of
stuffing box. (Fig. 5 & 6)
Fig. 5
Fig. 6
32
6. Install split gland (350.12427) behind packing. (Fig. 7)
Fig. 7
7. Install gland plate (350.12429) and hand tighten the

socket head cap screws (70.43374) If using torque
wrench, tighten to between 100 – 120 in. oz. or 6.25 –
7.5 in. lbs. ( DO NOT OVER TIGHTEN. (Fig. 8)
8. Install shaft sleeve (350.12435). (Fig. 9) Fig. 8
9. Carefully install seal head (350.12411) assembly onto

the power frame (350.2016). (Fig. 10)
10. Spray seal both faces with WD-40 or similar product to Fig. 9
make sure they are free of contaminants.
11. Using a soapy water or alcohol hand sanitizing solution

to aid in installtion, slide rotating half of the Fig. 10
mechanical seal over the sleeve until the faces meet.
Be careful not to “slap” the faces together or they
could be damaged. Use caution so as not to cause the
rubber bellows to “curl” while pressing the rotating
half into position. CAUTION – Do not use oil, grease or
other lubicants to slide rotating half of seal on to the
sleeve unless they are specifically designed for that Fig. 11
purpose. Oil or grease may cause the rubber bellow
to slip on the shaft during operation causing the seal
to leak. (Fig. 11)
12. Install the retaining spring . (Fig. 12)
Fig. 12
33
13. Coat O-ring grove with Never-Seize or grease and
install impeller O-ring (70.80608) in O-ring groove on
back side of impeller (350.12414, 350.12431,
350.20501). Never-Seize or grease will hold o-ring in
place during impeller installation (Fig. 13 ).
Fig. 13
14. Install impeller impeller and adjust per instruction on

page 29. (Fig. 14)
15. Seal installation can be facilitated by the use of a seal

installation tool. (Fig. 15) It can be fabricated per the
drawing Fig. 16. The tool is usefull during installation
and removal of both the stationary and rotating halves
of the seal.
Fig. 14
Fig. 15
Fig. 16
34
Seal Lubricants and Suggested Service Rating
Service Seal Type Lubricant Rating

Cementing Lip Seal Pressurized Oil A
(C-3 or Dexron)
Grease B
Packing Grease B
Mechanical Seal None Not
Recommended
Fracturing Slurry Lip Seal Pressurized Oil A
(C-3 or Dexron)
Packing Grease B
Mechanical Seal None Not
Recommended
Mud Circulation Lip Seal Pressurized Oil X
(C-3 or Dexron)
Packing Grease A
Mechanical Seal Clean Flush Liquid X
Water (Fresh) Lip Seal Pressurized Oil A
(C-3 or Dexron)
Packing Grease B
Mechanical Seal None A
Water (Sea) Lip Seal Pressurized Oil A
(C-3 or Dexron)
Packing Grease B
Mechanical Seal None X
Key
A Acceptable Preferred
B Acceptable Secondary
X Untested Performance Unknown
35
Section 4
Troubleshooting Guide
Warning: Before trying to open or service the pump:
• Lockout or disconnect the power source to pump.
• Allow pump to completely cool if overheated.
• Failure to follow the operating instruction warnings of hazards or
unsafe practices could result in injury or death.
Trouble Shooting
Symptom Potential Causes Corrective Action
1. No Liquid Delivered. a. Pump not primed. Fill pump and pump suction line with
water.
b. Speed too slow. Check pump shaft speed with
tachometer. Increase speed as needed.
c. Discharge head too high. Make sure there are no obstruction in

the discharge line, all valves are open,
and that discharge hose is the correct
length and diameter. Check with
pressure gauge at pump discharge.
d. Suction lift too high or restricted. Remove any obstructions. Make sure
liquid viscosity is not to high. Check
with vacuum gauge at pump suction.
Check suction valves to make sure they
are open and unrestricted by debris.
e. Impeller completely plugged. Remove suction cover and clear

obstruction.
f. Wrong direction of rotation. If pump is not locked up, check
clearances and correct rotation.
g. Viscosity too high (too thick). Reduce liquid viscosity making fluid
thinner.
36
2. Not Enough Liquid Delivered. a. Air leak in suction pipe or stuffing Adjust packing or repair mechanical
box. seal. Check suction line and connects
for leaks.
b. Speed too low. Check pump shaft speed with
c. Discharge head higher than Make sure there are no obstruction in

anticipated. the discharge line, all valves are open,
and that discharge hose is the correct
length and diameter. Check with
pressure gauge at pump discharge.
d. Suction lift too high. Remove any obstructions. Make sure

e. Impeller partially plugged Remove suction cover and clear

obstruction.
f. Not enough suction head Increase liquid level in supply tank.
g. Mechanical defects. Check for worn or damaged impeller or

pump casing.
h. Impeller clearances set too wide. Check and adjust impeller clearances.
3. Not Enough Pressure a. Speed too slow. Check pump shaft speed with
b. Air in liquid. Adjust packing or repair mechanical

seal. Check suction line and
connections for leaks. Increase liquid
level in supply tank.
c. Mechanical defects. Check for worn or damaged impeller or

pump casing.
d. Impeller diameter too small. Remove impeller and install correct
diameter impeller.
e. Impeller clearances set too wide. Check and adjust impeller clearances.
4. Pump Works for a While and then a. Leak in suction line. Adjust packing or repair mechanical
Quits. seal. Check suction line and connects
for leaks. Increase liquid level in supply
tank.
b. Suction plugged or restricted. Remove any obstructions. Make sure

37
c. Suction lift too high. Remove any obstructions. Make sure
Increase liquid level in supply tank.
5. Pump Takes Too Much Power. a. Speed too high. Reduce pump speed.
b. Discharge head lower than rating, Partially close discharge valve to
pumps too much liquid. produce more head pressure on pump
discharge.
c. Liquid viscosity is too high, liquid Reduce liquid viscosity. Reduce flow
heavier than water or both. rate for high fluid weights.
d. V-belts too loose. Adjust belt tension to manufactures
specifications. Replace belts if glazed
or damaged.
e. Shaft bent. Replace shaft.
f. Impeller rubbing on casing. Check and adjust impeller clearances.
g. Stuffing box packing too tightly Do not over tighten packing. Allow
adjusted. liquid to drip thru packing for shaft
lubrication. Regrease packing.
6. Bearings Overheating a. Bearing out of adjustment. Check and adjust impeller clearances.
b. V-belts too tight. Adjust belt tension to manufactures
specifications.
c. Lack of lubrication. Grease per manufacturer's
recommendations.
d. Excessive lubrication. Remove excess grease. Grease per
manufacturer's recommendations.
d. Shaft bent. Replace shaft.
e. Bearings installed in face-to-face Replace bearings. Install in back-to-
arrangement instead of back-to back back arrangement.
arrangement.
f. Drive misaligned or excessive Check alignment. Remove preload
preload on shaft. from shaft.
7. Mechanical Seal Leaks. a. Mechanical seal has failed. Replace seal.

b. Lack of fluid has allowed seal to run Replace seal.
dry.
c. Cavitation has caused seal to fail. Replace seal.
8. Lip Seals Leak. a. Lips seals worn. Replace lip seals.

b. Shaft sleeve worn. Replace shaft sleeve and lip seals.
c. Seal oil supply tank pressure set too Check level in oil supply tank.
high.
38
9. Shaft breaks behind impeller. a. Pump speed too high. Reduce pump speed.
b. Obstruction in impeller. Remove suction cover and remove
obstruction.
10. Excessive Noise a. Cavitation in pump. Remove any obstructions. Make sure
b. Pumping entrained air. Check for leaks in suction line or

evidence of vortexing at the pump
suction.
c. Pump not mounted securely. Inspect and repair installation.
d. Impeller clogged or damaged. Remove any obstructions. Replace
damaged part.
11. Shaft breaks at rear bearing. a. V-belts too tight. Adjust belt tension to manufactures
specifications.
b. Lack of lubrication. Replace bearings, readjust per
manufacturer's instructions and re-
grease bearings.
39
Section 5
Parts Breakdowns
Halliburton 350.205 Size 4 X 4 X 12 - 12" Impeller Lip Seal Design

SAP 100011824
Item SAP Part Description Quan.

Number Req.
1 100003125 350.2016 Power End Assembly 100 BHP 1
2 100003081 350.12412 Box - Stuffing - Lip Seal or Packing 1
3 100002398 70.80607 Seal- Oil 4
4 100003099 350.15293 Lantern Ring - 20623 1
5 100011791 350.12429 Plate - Gland 1
6 100059329 350.12420 Ring - Gland 1
7 100003127 350.20501 Impeller 12" Diameter 1
8 100003128 350.20502 Casing 1
9 100003087 350.12435 Sleeve - Shaft 1
10 100011794 350.12439 Strap - Lifting 1
11 100059337 350.12436 Plate - Identification 1
12 100034168 70.85981 Adapter - Hose-45 Deg Brass 1/4 Tube x 1/8-27MPT x 9/16- 4
18 JIC
13 100032686 70.79319 Adapter - Hose -1/4 Tube x 9/16-18 JIC 4
40
14 100002169 70.43374 Screw - Hex SOC 3/8-16NC x 1-1/4 2
15 100012922 70.32916 Nut Hex 3/4-10NC 4
16 100013142 70.80613 Screw - Set - 3/4-10UNC-3A x 3 Cup Point 4
17 100013143 70.80614 Screw - Set - 3/4-10UNC-3A x 2 Cup Point 4
18 100012924 70.32992 Nut - Hex Jam - 3.4-10NC 4
19 100001993 70.34019 O-Ring - 70D 12-1/2 x 12 x 1/4 1
20 100016568 26.1 Pipe Plug 1/8 IN. - CI 2
21 100016593 26.5 Plug - Pipe - 3/4 IN CI 1
22 100002399 70.80608 O-Ring - 70D 2 x 1-7/8 x 1/16 1
23 100002400 70.80609 O-Ring - 70D 2-1/8 x 2 x 1/16 1
24 100029924 70.58962 Washer - Lock - 5/8 - STL 5
25 100028511 70.43897 Screw - Hex Cap 5/8-11NC x 1-3/4 5
41
350.205-11.25
Halliburton 350.205-11.25 Size 4 X 4 X 12 – 11.25" Impeller Lip Seal Design

SAP 101646801

# Number Req.
1 100003125 350.2016 Power End Assembly 100 BHP 1
2 100003081 350.12412 Box - Stuffing - Lip Seal or Packing 1
3 100002398 70.80607 Seal- Oil 4
4 350.15293 Lantern Ring - 20623 1
5 350.12429 Plate - Gland 1
6 350.12420 Ring - Gland 1
7 350.20501A Impeller 11.25" Diameter 1
8 350.20502 Casing 1
9 350.12435 Sleeve - Shaft 1
10 350.12439 Strap - Lifting 1
11 350.12436 Plate - Identification 1
12 70.77872 Adapter Hose Cap 9/16-18 JIC Size 6 2
13 70.796714 Adapter Hose 45 Deg 9/16-18 JIC X 1/8-27 NPT 2

14 70.43374 Screw - Hex SOC 3/8-16NC x 1-1/4 2
15 70.32916 Nut Hex 3/4-10NC 4
16 70.80613 Screw - Set - 3/4-10UNC-3A x 3 Cup Point 4
18 70.32992 Nut - Hex Jam - 3.4-10NC 4
19 70.34019 O-Ring - 70D 12-1/2 x 12 x 1/4 1
20 26.1 Pipe Plug 1/8 IN. - CI 2
42
21 26.5 Plug - Pipe - 3/4 IN CI 1
22 70.80608 O-Ring - 70D 2 x 1-7/8 x 1/16 1
23 70.80609 O-Ring - 70D 2-1/8 x 2 x 1/16 1
24 70.58962 Washer - Lock - 5/8 - STL 5
25 70.43897 Screw - Hex Cap 5/8-11NC x 1-3/4 5
43
Halliburton 350.205-11.25 Size 4 X 4 X 12 – 12.00" Impeller Teflon Lip Seal Design, HALAR coated
Impeller
SAP
# Number Req.
1 350.2016 Power End Assembly 100 BHP 1
2 350.12412 Box - Stuffing - Lip Seal or Packing 1
3 70.80607 Seal - Oil -2.500 B X 3.500 OD X .437 W 3
4 350.15293 Lantern Ring - 20623 1
5 350.12429 Plate - Gland 1
6 350.12427 Ring - Gland 1
7 350.20510 Impeller 12" Diameter Coated 1
8 350.20502 Casing 1
9 350.12435 Sleeve - Shaft 1

14 70.43374 Screw - Hex SOC 3/8-16NC x 1-1/4 2
15 70.32916 Nut Hex 3/4-10NC 4
18 70.32992 Nut - Hex Jam - 3.4-10NC 4
19 70.34019 O-Ring - 70D 12-1/2 x 12 x 1/4 1
20 70.80954 O-Ring - 70D 12-1/4 x 12 x 1/8 3
21 26.5 Plug - Pipe - 3/4 IN CI 1
44
22 Not Shown
23 7.33684 O-Ring - 70D 2 x 1-7/8 x 1/16 Fluorocarbon 1
23 70.80609 O-Ring - 70D 2-1/8 x 2 x 1/16 1
24 70.58962 Washer - Lock - 5/8 - STL 5
25 70.43897 Screw - Hex Cap 5/8-11NC x 1-3/4 5
27 Not Shown
29 350.20560 Teflon PTFE Lip Seal 2
45
Halliburton 350.1241 Size 6 X 5 X 11 - 10" Impeller - Mechanical Seal Design
SAP 100059322
Item SAP Part # Description Quan.

# Req.
1 350.12411 Box - Stuffing - Mechanical Seal 1
2 350.12413 Casing - Pump Cent - 6X5X10 1
3 350.12414 Impeller - 10" Dia. Pump Cent. 1
5 350.12427 Ring - Gland 1
6 350.12435 Sleeve - Shaft 1
7 Not Shown
16 26.5 Plug - Pipe 3/4" CI 2
18 350.12438 Packing Ring 3.5 X 2.5 graphite 1
19 70.80608 O-Ring - 70D-2 X 1-7/8" X 1/16" 568-032 1
20 70.80609 O-Ring - 70D 2-1/8 X 2 X 1/16 568-033 1
23 70.34019 O-Ring - 70D - 12-1/2 X 12 X 1/4 568-453 1
25 70.80613 Screw - Set 3/4"-10UNC-3A X 3 Cup Point HT Alloy 4
Steel - Zinc Plated 40 RC
27 350.15318 Mechanical seal TC/TC 1
28 70.43897 Screw - Hex Cap - 5/8-1NC X 1-3/4- Plated 5
33 70.32916 Nut Hex 3/4-10NC 4
46
34 70.32992 Nut - Hex Jam - 3.4-10NC 4
37 70.58962 Washer - Lock 5/8" -Steel - Plated 5
41 26.1 Plug - Pipe 1/8 - CI 4
46 350.12429 Plate - Gland 1
47 70.80954 O-Ring - 70D - 12-1/4 X 12 X 1/8 568-278 3
48 70.43371 Screw - Hex Socket - 3/8-16NC X 3/4 2
53 Not Shown 1
60 70.81033 Roll Pin SS 1/8 x 3/4 1
47
Halliburton 350.1242 Size 6 X 5 X 11 - 10" Impeller - Lip Seal Design
SAP 100011789

# Req.
5 Not Shown
6 350.12435 Sleeve - Shaft 1
16 26.5 Plug - Pipe 3/4" CI 2
18 70.80607 Seal - Oil -2.500 B X 3.500 OD X .437 W 4
19 70.80608 O-Ring - 70D-2 X 1-7/8" X 1/16" 568-032 1
20 70.80609 O-Ring - 70D 2-1/8 X 2 X 1/16 568-033 1
23 70.34019 O-Ring - 70D - 12-1/2 X 12 X 1/4 568-453 1
27 350.15293 Lantern Ring 1
33 70.32916 Nut Hex 3/4-10NC 4
34 70.32992 Nut - Hex Jam - 3.4-10NC 4
48
46 350.12429 Plate - Gland 1
47 26.1 Pipe Plug 1/8 IN. - CI 2
48 70.43374 Screw - Hex Socket - 3/8-16NC X 1-1/4 2
53 Not Shown
60 350.12427 Ring - Gland 1
60 350.12420 Ring - Gland 1
49
Halliburton 350.1243 Size 6 X 5 X 11 - 11" Impeller - Mechanical Seal Design
SAP 120021877

# Req.
1 350.12411 Box - Stuffing - Mechanical Seal 1
5 Not Shown
6 350.12435 Sleeve - Shaft 1
7 Not Shown
8 350.12427 Ring - Gland 1
16 26.5 Plug - Pipe 3/4" CI 2
18 350.12438 Packing Ring 3.5 X 2.5 graphite 1
19 70.80608 O-Ring - 70D-2 X 1-7/8" X 1/16" 568-032 1
20 70.80609 O-Ring - 70D 2-1/8 X 2 X 1/16 568-033 1
23 70.34019 O-Ring - 70D - 12-1/2 X 12 X 1/4 568-453 1
25 70.80613 Screw - Set 3/4"-10UNC-3A X 3 Cup Point HT Alloy Steel - 4
Zinc Plated 40 RC
Zinc Plated 40 RC
27 350.15318 Mechanical seal TC/TC John Crane 1
33 70.32916 Nut Hex 3/4-10NC 4
34 70.32992 Nut - Hex Jam - 3.4-10NC 4
50
41 26.1 Plug - Pipe 1/8 - CI 4
46 350.12429 Plate - Gland 1
47 70.80954 O-Ring - 70D - 12-1/4 X 12 X 1/8 568-278 3
48 70.43371 Screw - Hex Socket - 3/8-16NC X 3/4 2
60 70.81033 Roll Pin SS 1/8 x 3/4 1
51
Halliburton 350.1244 Size 6 X 5 X 11 - 11" Impeller - Lip Seal Design
SAP 100011795

# Req.
5 Not Shown
6 350.12435 Sleeve - Shaft 1
7 Not Shown
16 26.5 Plug - Pipe 3/4" CI 2
18 70.80607 Seal - Oil -2.500 B X 3.500 OD X .437 W 4
19 70.80608 O-Ring - 70D-2 X 1-7/8" X 1/16" 568-032 1
20 70.80609 O-Ring - 70D 2-1/8 X 2 X 1/16 568-033 1
23 70.34019 O-Ring - 70D - 12-1/2 X 12 X 1/4 568-453 1
Zinc Plated 40 RC
Zinc Plated 40 RC
33 70.32916 Nut - Hex -3/4-10NC 4
34 70.32992 Nut - Hex Jam -3/4-10NC 4
46 350.12429 Plate - Gland 1
52
47 26.1 Plug - Pipe 1/8 NPT CI 2
60 350.12420 Ring - Gland 1
53
Halliburton 350.202 Size 8 X 6 X 14 - 14" Impeller - Lip Seal Design - 100 BHP Frame
SAP 101308220

# Number Req.
3 70.80607 Seal - Oil -2.500 B X 3.500 OD X .437 W 5
5 350.12429 Plate - Gland 1
6 350.12427 Ring - Gland 1
9 350.12435 Sleeve - Shaft 1
10 350.20205 Strap - Lifting - 8 x 6 x 14 Pump 1

15 70.83335 Screw - Set - 7/8-9UNC - 3AX3.0 Cup Point HT Alloy Steel - 8
Zinc Plated 40 RC
16 70.32994 Nut - Hex Jam - 7/8-9UNC - PL 4
17 70.32917 Nut Hex 7/8-9NC- PL 4
18 70.83333 O-Ring -70D - 16.5 X 116.0 X1/4 568-461 1
19 70.34019 O-Ring - 70D - 12-1/2 X 12 X 1/4 568-453 1
20 350.20206 Mount - Front - 8 X 6 X 14 100BHP 1
54
21 26.6 Plug - Pipe 1" STL - SQ HD 3
22 70.80608 O-Ring - 70D-2 X 1-7/8" X 1/16" 568-032 1
23 70.80609 O-Ring - 70D 2-1/8 X 2 X 1/16 568-033 1
26 Not Shown
27 Not Shown
28 350.20204 Mount - Rear - 8X6X14 - 100BHP 1
29 350.20202 Adapter - Stuffing Box - 8X6X14 Pump to 100BHP Power end 1
30 70.43924 Screw - Hex Cap - 3/4-10NC X 2 - PL 4

31 Not Shown
32 70.58964 Washer - Lock 3/4 - STL - PL 4
55
350.2016 Power End Assembly - 100 BHP - Centrifugal Pump
SAP 100003125
Item Part Description Quan.

# Number Req.
1 70.43903 Screw- Hex cap -5/8-11NC x 2-1/4 3
2 70.32915 Nut - Hex 5/8-11NC 3
3 350.12432 Frame - Cast Ductile Iron 1
4 350.12416 Shaft 1
5 350.12418 Housing - Bearing - Rear 1
6 350.12419 Cap - Bearing - Rear 1
7 350.12421 Cap - Bearing - Front 1
8 350.12422 Mount - Front - STD 1
9 350.12423 Mount - Rear - STD - Single Hole 1
10 70.04136 Bearing - Ball - 7311 Duplex 2
11 70.80602 Bearing - Ball - 6411 Simplex 1
12 70.80603 Seal - Oil - 21159 1
13 70.80604 Seal - Oil - 21163 1
14 70.80606 Seal - Oil - 9189 LPD 1
15 8.34051 O-Ring - 90D - 5-3/4 x 5-1/2 x 1/8 1
16 70.80612 O-Ring - 70D - 5-1/2 x 5-1/4 x 1/8 1
17 8.33988 O-Ring - 90D - 4-3/4 x 4-3/8 x 3/16 1
18 70.43872 Screw- Hex cap -1/2-13NC x 2 4
19 70.43868 Screw - Hex cap - 1/2-13NC x 1-1/2 2
20 70.43814 Screw - Hex cap - 3/8-16NC x 1 2
21 70.32914 Nut - Hex 1/2-13NC 2
22 70.32989 Nut - Hex Jam 1/2-13NC 2
23 70.58962 Washer - Lock 5/8 3
24 70.58959 Washer - Lock 1/2 2
25 70.58806 Washer - Flat 3/8 4
26 70.22933 Fitting - Grease 1/8 straight 1
27 26.10102 Plug - Pipe 1/8 SS Hex socket Head 3
56
28 106.54711 Vent - Air - 301370 -1/8 NPT 1
29 70.09091 Nut - Lock - N11 1
30 70.09111 Washer - Lock - W11 1
31 26.2 Plug - Pipe 1/4 CI 1
32 350.12433 Key - Square - 1/2 x 1/2 x 3 1
33 350.12434 Slinger - Shaft 1
34 70.43816 Screw - Hex Cap 3/8-16NC x 1-1/4 2
35 70.22931 Fitting - Grease - 1/8 45 Deg 2
36 70.58955 Washer - Lock 3/8 4
57
350.201 8 X 6 x 14 HD Centrifugal Pump - Packing Design
SAP 101573750

# Number Req.
1 350.20102 Casing - Pump Centrifugal 8x6x14 1
2 350.20103 Box - Stuffing - Packing - Pump Centrifugal - 8x6x14 1
3 350.20122 Frame - Pump Centrifugal 8x6x14 1
5 70.32917 Nut - Hex - 7/8-9NC - Plated 4
6 70.43924 Screw - Hex Cap - 3/4-10NC x 2 - Plated Spec70.43917 8
7 70.58964 Washer - Lock - 3/4 - Plated Spec. 70.59034 14
8 70.43381 Screw - Hex Cap - 1/2-13NC x 1-1/4 - Plated Spec70.43270 2
9 350.20124 Cap - Bearing - Front - Pump - Centrifugal 8x6x14 1

10 70.22933 Fitting - Grease - 1/8 - Straight - Drive 1
11 70.83282 Bearing - Ball - 322S -4.331 B x 9.448 OD x 1.969 W - 1
Single Row - Radial - MRC Only
12 70.83333 O-Ring - 70D - 16.5 - x 16.0 x 1/4 - 568-461 - Spec 1
70.33000 Spec 70.72000
13 70.83357 Seal - Oil - Chicago Rawhide - 42470- 4.250 B x 5.256 OD x 1
.250 W
14 70.83283 Seal - Oil - Chicago Rawhide - 42422- 4.250 B x 5.256 OD x 1
.375 W
15 26.1 Plug - Pipe - 1/8 Inch - CI 2
16 350.20107 Plate - Gland - Pump Centrifugal 8x6x14 1
17 70.32728 Slinger - Pump Centrifugal 8x6x14 1
18 350.20106 Ring - Gland - Pump Centrifugal 8x6x14 1
58
19 70.83334 O-Ring - 70D - 4-1/8 x 4.0 x 1/16 - 568-045 - Spec 70.33000 2
Spec 70.72000
20 350.20105 Lantern Ring - 6 Inch OD x 4.75 Inch ID Pump Centrifugal 1
8x6x14
21 106.54711 Vent - Air - 301370 - 1/8" NPT - Alemite 1
22 70.83284 Bearing - Ball - 4.3307 B x 7.8740 OD x 1.4960 W - Single 1
Row - Angular Contact - 40 Deg Contact Angle - 1/2 Pair
23 8.34066 O-Ring - 90D -9-1/4x9x1/8 - 568-270 - Spec 8.33001 Spec 1
70.72000
24 350.20126 Housing - Bearing - Rear - Pump Centrifugal 8x6x14 1
25 70.43898 Screw - Hex Cap - 5/6-11NC x 2 - Plated Spec70.43917 4
26 70.34016 O-Ring - 90D -8-1/4x7-3/4x1/4 - 568-444 - Spec 599.33 1
Spec 70.72000
27 350.20125 Cap - Bearing - Rear - Pump - Centrifugal 8x6x14 1
28 70.33254 Nut - Lock - AN-22 1
29 70.59086 Washer - Lock - W-22 1
30 70.36972 Plug - Pipe - 1/4 Inch - Square Head - Steel 4
31 70.80606 Seal - Oil - 9189 LPD - 1.875 B x 2.750 OD x .375 W - 1
Johns Mansville Only
32 350.12433 Key - Square - 1/2 x 1/2 x 3 1
33 350.20123 Shaft - Pump Centrifugal 8x6x14 1
35 70.32996 Nut - Hex - Jam - 5/8-11NC - Plated Spec 70.32869 2
36 70.34068 O-Ring - 90D 9-3/4 x 9-1/2 x 1/8 568-272 Spec 599.33001 1
Spec 70.72000
37 70.32916 Nut - Hex - 3/4-10NC - Spec 70.32869 3
38 350.12436 Plate - Identification - Pump Centrifugal 1
39 350.20127 Mount - Rear - Pump - Centrifugal 8x6x14 1
40 26.10102 Plug - Pipe - 1/8 Inch - Stainless Steel Hex Socket Head 3
41 68.00102 Paint Spec - Coating 68.00102 1
42 70.36981 Plug - Pipe - 1/2 Inch Socket Head 1
43 70.43926 Screw - Hex Cap - 3/4-10NC x 2-1/4 - Plated Spec70.43917 6
44 350.20128 Mount - Front - Pump - Centrifugal 8x6x14 1

45 70.83335 Screw - Set 7/8-9UNC - 3Ax3.0 - Cup point - Hex Socket - 8
HT Alloy Steel - Zinc Plated - RC 40 Maximum -
Hollowkrome Only - Spec
46 70.32994 Nut - Hex Jam - 7/8-9NC - Plated Spec 70.32869 4
47 26.6 Plug - Pipe - 1 Inch - Cast Iron 2
48 350.20108 Packing Set - 6 x 4-3/4 - 4 Rings - Carbon Yarn - Graphite 1
Impregnated - Spec
49 350.20104 Sleeve - Shaft Pump - Centrifugal Lip seal 8x6x14 1
50 350.20101 Impeller - Pump - Centrifugal 8x6x14-14 1
51 70.83337 O-Ring - 70D -3-5/8 x 3-1/2 x 1/16 -568-043 Spec 70.33000 1
Spec 70.72000
52 70.43816 Screw - Hex Cap - 3/8-16NC x 1-1/4 - Plated Spec 2
70.43917
53 70.58955 Washer - Lock - 3/8 - Steel - Plated Spec 70.59304 2
54 70.43895 Screw - Hex Cap - 5/8-11NC x 1-1/4 - Plated Spec 2
70.43917
55 70.58962 Washer - Lock - 5/5 - Steel - Plated Spec 70.59034 2
56 350.20149 Spec - Pump Test - Pump - Centrifugal 8x6x14 1
57 350.20110 Strap - Lifting - Pump - Centrifugal 8x6x14 - 300 BHP Power 1
End
59
350.203
Halliburton 350.203 Size 8 X 6 X 14 - 14" Impeller - Lip Seal Design - 300 BHP Small Frame
SAP 101761420

# Number Req.
1 350.20316 Shaft - 300 HP - Small Frame 1
3 70.80607 Seal - Oil -2.500 B X 3.500 OD X .437 W 4
5 350.12429 Plate - Gland 1
6 350.12420 Ring - Gland 1
7 350.20201 Impeller - 14.375" Dia. Pump Cent. 1
9 350.20335 Sleeve - Shaft 1
10 350.20205 Strap - Lifting - 8 x 6 x 14 Pump 1

15 70.83335 Screw - Set - 7/8-9UNC - 3AX3.0 Cup Point HT Alloy Steel - 8
Zinc Plated 40 RC
16 70.32994 Nut - Hex Jam - 7/8-9UNC - PL 4
17 70.32917 Nut Hex 7/8-9NC- PL 4
60
18 70.83333 O-Ring -70D - 16.5 X 116.0 X1/4 568-461 1
19 70.34019 O-Ring - 70D - 12-1/2 X 12 X 1/4 568-453 1
20 350.20206 Mount - Front - for 12.5 Shaft C/L (350.203L) 1
21 26.6 Plug - Pipe 1" STL - SQ HD 3
22 70.80609 O-Ring - 70D 2-1/8 X 2 X 1/16 568-033 1
23 70.80609 O-Ring - 70D 2-1/8 X 2 X 1/16 568-033 1
26 350.20204 Mount - Rear for 12.5 Shaft C/L (350.203L) 1
27 70.43924 Screw - Hex Cap - 3/4-10NC X 2 - PL 4
28 8.34051 O-Ring - 90D - 5-3/4 x 5-1/2 x 1/8 1
29 350.20202 Adapter - Stuffing Box - 8X6X14 Pump to 100BHP Power End 1
30 350.12421 Cap - Bearing - Front 1

31 70.80603 Seal - Oil - 21159 1
32 70.80604 Seal - Oil - 21163 1
33 106.54711 Vent - Air - 301370 -1/8 NPT 1
35 70.80612 O-Ring - 70D - 5-1/2 x 5-1/4 x 1/8 1
36 70.43868 Screw - Hex cap - 1/2-13NC x 1-1/2 2
37 350.12418 Housing - Bearing - Rear 1
38 350.12419 Cap - Bearing - Rear 1
39 9120 Seal - Oil - NBR LUP 2.000 2.750 .438 - 9120 H1L5 1
40 8.33988 O-Ring - 90D - 4-3/4 x 4-3/8 x 3/16 1
41 70.09111 Washer - Lock - W11 1
42 70.09091 Nut - Lock - N11 1
43 70.43872 Screw- Hex cap -1/2-13NC x 2 2
44 70.32989 Nut - Hex Jam 1/2-13NC 2
45 70.04136 Bearing - Ball - 7311 Duplex 2
46 70.43872 Screw - Hex cap - 1/2-13NC x 2 2
47 70.32914 Nut - Hex 1/2-13NC 2
48 350.12434 Slinger - Shaft 1
49 SKF Bearing - Ball - 21313E - Spherical Roller Bearing 1
21313E
52 350.12432 Frame - Cast Ductile Iron 1
54 70.58959 Washer - Lock 1/2 2
55 70.58964 Washer, Lock - 3/4 - Steel 4
56 70.43814 Screw - Hex cap - 3/8-16NC x 1 2
57 70.58806 Washer - Flat 3/8 4
20a 350.12422 Mount - Front - for 8.5 Shaft C/L (350.203S) 1
26a 350.12423 Mount - Rear for 8.5 Shaft C/L (350.203S) 1
70.22931 Fitting - Grease - 1/8 45 Deg - Bearing Cap (Not Shown) 2
70.22933 Fitting - Grease 1/8 straight - Frt Bearing Cap (Not Shown) 1
350.12433 Key - Square - 1/2 x 1/2 x 3 - Input Shaft (Not Shown) 1
Optional Mechanical Seal

50 350.15318 Mechanical seal TC/TC John Crane 1
2a 350.12411 Box - Stuffing - Mechanical Seal 1
53 350.12427 Ring - Gland 1
52 350.12438 Packing Ring 3.5 X 2.5 Graphite 1
61
Legacy to SAP Part Crossover
Legacy Part # Halliburton Description
SAP Part #
7.33684 100015357 O-Ring - 70D 2 x 1-7/8 x 1/16 Fluorocarbon
8.33988 100013720 O-Ring - 90D - 4-3/4 x 4-3/8 x 3/16
8.34051 100000979 O-Ring - 90D - 5-3/4 x 5-1/2 x 1/8
8.34066 100015436 O-ring - 90D - 9-1/4 X 9 X 1/8 -568-270
26.1 100016568 Pipe Plug 1/8 IN. - CI
26.10102 100016570 Plug - Pipe 1/8 Stainless Steel Hex Socket Head
26.2 100016573 Plug - Pipe 1/4 CI
26.5 100016593 Plug - Pipe - 3/4 IN CI
26.6 100016601 Plug - Pipe - 1 IN STL - SQ HD
68.00102 100020311 Coating per spec.
70.09091 100001510 Nut - Lock - N11
70.09111 100001511 Washer - Lock - W11
70.22931 100024706 Fitting - Grease - 1/8 45 Deg
70.22933 100024708 Fitting - Grease 1/8 straight
70.32728 100026448 Shaft Slinger
70.32914 100026525 Nut - Hex 1/2-13NC
70.32915 100026526 Nut - Hex 5/8-11NC
70.32916 100012922 Nut Hex 3/4-10NC
70.32917 100026527 Nut Hex 7/8-9NC -PL
70.32989 100026551 Nut - Hex Jam 1/2-13NC
70.32992 100012924 Nut - Hex Jam - 3.4-10NC
70.32994 100026553 Nut - Hex Jam - 7/8-9UNC - PL
70.32996 100001872 Hex Jam Nut - 5/8-11NC - PL
70.33254 100026632 Lock Nut - AN-22
70.34016 100026847 O-ring - 90D - 8-1/4 X 7-3/4 X 1/4 - 568-444
70.34019 100001993 O-Ring - 70D - 12-1/2 X 12 X 1/4 568-453
70.34068 100026855 O-ring - 90D - 9-3/4 X 9-1/2 X 1/8 - 568-272
70.36972 100027498 Pipe Plug - 1/4 NPT - Sq. Hd. Steel
70.36981 100027505 Pipe Plug - 1/2 NPT - Sq. Hd. Steel
70.43374 100002169 Screw - Hex Socket - 3/8-16NC X 1-1/4
70.43381 100028247 Hex Socket Screw - 1/2-13NC X 1-1/4
70.43814 100013017 Screw - Hex cap - 3/8-16NC x 1
70.43816 100028455 Screw - Hex Cap 3/8-16NC x 1-1/4
70.43868 100028505 Screw - Hex cap - 1/2-13NC x 1-1/2
70.43872 100028492 Screw- Hex cap -1/2-13NC x 2
70.43895 100028509 Screw-Hex Cap - 5/8-11NC X 1-1/4 -PL
70.43897 100028511 Screw - Hex Cap - 5/8-1NC X 1-3/4- Plated
70.43898 100028512 Screw - Hex Cap - 3/4-10NC X 2-1/4 - PL
70.43903 100028515 Screw- Hex cap -5/8-11NC x 2-1/4
70.43924 100028525 Screw - Hex Cap - 3/4-10NC X 2 - PL
70.43926 100028527 Screw - Hex Cap - 3/4-10NC X 2-1/4 - PL
70.58806 100029874 Washer - Flat 3/8
70.58955 100013059 Washer - Lock 3/8
70.58959 100002256 Washer - Lock 1/2
70.58962 100029924 Washer - Lock 5/8" -Steel - Plated
70.58964 100029925 Washer - Lock 3/4 - STL - PL
70.59086 100029956 Lock Washer - W-22
70.77872 100032333 Adapter Hose Cap 9/16-18 JIC Size 6
62
SAP Part #
70.79319 100032686 Adapter - 210292-4S - Brass- 1/4 OD Tube - x 7/16-20 JIC
70.80603 100013140 Seal - Oil - 21159
70.80604 100002396 Seal - Oil - 21163
70.80606 100002397 Seal - Oil - 9189 LPD
70.80607 100002398 Seal - Oil -2.500 B X 3.500 OD X .437 W
70.80608 100002399 O-Ring - 70D-2 X 1-7/8" X 1/16" 568-032
70.80609 100002400 O-Ring - 70D 2-1/8 X 2 X 1/16 568-033
70.80612 100013141 O-Ring - 70D - 5-1/2 x 5-1/4 x 1/8
70.80613 100013142 Screw - Set 3/4"-10UNC-3A X 3 Cup Point HT Alloy Steel - Zinc Plated 40 RC
70.80614 100013143 Screw - Set 3/4"-10UNC-3A X 2 Cup Point HT Alloy Steel - Zinc Plated 40 RC
70.80954 100002403 O-Ring - 70D - 12-1/4 X 12 X 1/8 568-278
70.81033 100033017 Roll Pin SS 1/8 x 3/4
70.83282 100033517 Ball Bearing 322S MRC
70.83283 100033518 Seal - Oil - CR 42422 - 4.250B X 5.256OD X.375W
70.83284 100033519 Bearing - Ball - 4.3307 B x 7.8740 OD x 1.4960 W - Single Row - Angular
Contact - 40 Deg Contact Angle - 1/2 Pair -SKF 7222BAG
70.83333 100002431 O-Ring -70D - 16.5 X 116.0 X1/4 568-461
70.83334 100033535 O-Ring -70D - 4 1/8 X 4.0 X1/16 568-045
70.83335 100033536 Screw - Set - 7/8-9UNC - 3AX3.0 Cup Point HT Alloy Steel - Zinc Plated 40 RC
70.83337 100033537 O-ring - 70D - 3-5/8 X 3-1/2 X 1/16 -568-043
70.83357 100033545 Oil Seal - 42470 - 4.25BX5.26ODX.250W
70.85981 100034168 Adapter - Hose 45 Deg - Brass- 1/4 OD Tube - 1/8 - 27 MPT x 7/16-20 JIC
70.96714 100035941 Adapter Hose 45 Deg 9/16-18 JIC 1/8-27 NPT
106.54711 100011066 Vent - Air - 301370 -1/8 NPT
350.12411 100003080 Stuffing Box - Mechanical Seal
350.12412 100003081 Box - Stuffing - Lip Seal or Packing
350.12413 100003082 Casing - Pump Cent - 6X5X10
350.12414 100003083 Impeller - 10" Dia. Pump Cent.
350.12416 100009363 Shaft
350.12418 100059325 Housing - Bearing - Rear
350.12419 100059327 Cap - Bearing - Rear
350.12420 100059329 Ring - Gland
350.12421 100059330 Cap - Bearing - Front
350.12422 100011790 Mount - Front - STD
350.12423 100059333 Mount - Rear - STD - Single Hole
350.12427 100003084 Ring - Gland Obsolete use 350.12420
350.12429 100011791 Plate - Gland
350.12431 100003085 Impeller - 11" Dia. Pump Cent.
350.12432 100011792 Frame - Cast Ductile Iron
350.12433 100011793 Key - Square - 1/2 x 1/2 x 3
350.12434 100003086 Slinger - Shaft
350.12435 100003087 Sleeve - Shaft
350.12436 100059337 Plate - Identification
350.12438 100003088 Packing - Carbon 1/2"
350.12439 100011794 Strap - Lifting
350.15293 100003099 Lantern Ring - 20623
350.15318 100059405 Mechanical Seal
350.20101 100059458 Impeller - Pump - Centrifugal - 14.375
350.20102 101201829 Casing - Pump Centrifugal - 8X6X14
350.20103 101005573 Box - Stuffing - Packing - Pump Centrifugal
63
SAP Part #
350.20104 100059460 Sleeve - Shaft Pump - Centrifugal Lip seal 8x6x14
350.20105 100059461 Lantern Ring - 6 Inch OD x 4.75 Inch ID Pump Centrifugal 8x6x14
350.20106 100014384 Ring - Gland - Pump Centrifugal 8x6x14
350.20107 101014710 Plate Gland
350.20108 100059462 Packing Set - 6 x 4-3/4 - 4 Rings - Carbon Yarn - Graphite Impregnated - Spec
350.20110 100059463 Strap - Lifting - Pump - Centrifugal 8x6x14 - 300 BHP Power End
350.20122 101573751 Frame - Pump Centrifugal 8x6x14 - 300 HP
350.20123 100059464 Shaft - Pump Centrifugal 8x6x14
350.20124 101573752 Cap - Bearing - Front - Pump - Centrifugal 8x6x14
350.20125 101573753 Cap - Bearing - Rear - Pump - Centrifugal 8x6x14
350.20126 100059465 Housing - Bearing - Rear - Pump Centrifugal 8x6x14
350.20127 100059466 Mount - Rear - Pump - Centrifugal 8x6x14
350.20128 100059467 Mount - Front - Pump - Centrifugal 8x6x14
350.2015 100003124 Service Manual
350.2016 100003125 Power End Assembly 100 BHP
350.20201 100003126 Impeller - 14" Dia. Pump Cent. 100 BHP
350.20202 120133378 Adapter - Stuffing Box - 8X6X14 Pump to 100BHP Power end
350.20204 100059469 Mount - Rear - 8X6X14 - 100BHP
350.20205 100059470 Strap - Lifting - 8 x 6 x 14 Pump
350.20206 100059471 Mount - Front - 8 X 6 X 14 100BHP
350.20301 No SAP Impeller - 14" Dia. Pump Cent.
350.20335 No SAP Sleeve - Shaft
350.20335 No SAP Sleeve - Shaft
350.20501 100003127 Impeller 12" Diameter 4 X 4
350.20502 100003128 Casing 4 X 4 X 12
350.20510 100059474 Impeller 12" Diameter Coated
350.20560 100059476 Teflon PTFE Lip Seal
350.20501A 101646568 Impeller 4x4 11.25" Diameter
70.04136 SKF 100001442 Bearing - Ball - 7311 Duplex
70.80602 SKF 100002395 Bearing - Ball - 6411 Simplex
350.2016HD No SAP Power End Assembly 300 BHP
64
SAP to Legacy Part Crossover
Halliburton Legacy Part # Description
SAP Part #
100000979 8.34051 O-Ring - 90D - 5-3/4 x 5-1/2 x 1/8
100001442 70.04136 SKF Bearing - Ball - 7311 Duplex
100001510 70.09091 Nut - Lock - N11
100001511 70.09111 Washer - Lock - W11
100001872 70.32996 Hex Jam Nut - 5/8-11NC - PL
100001993 70.34019 O-Ring - 70D - 12-1/2 X 12 X 1/4 568-453
100002169 70.43374 Screw - Hex Socket - 3/8-16NC X 1-1/4
100002256 70.58959 Washer - Lock 1/2
100002395 70.80602 SKF Bearing - Ball - 6411 Simplex
100002396 70.80604 Seal - Oil - 21163
100002397 70.80606 Seal - Oil - 9189 LPD
100002398 70.80607 Seal - Oil -2.500 B X 3.500 OD X .437 W
100002399 70.80608 O-Ring - 70D-2 X 1-7/8" X 1/16" 568-032
100002400 70.80609 O-Ring - 70D 2-1/8 X 2 X 1/16 568-033
100002403 70.80954 O-Ring - 70D - 12-1/4 X 12 X 1/8 568-278
100002431 70.83333 O-Ring -70D - 16.5 X 116.0 X1/4 568-461
100003080 350.12411 Stuffing Box - Mechanical Seal
100003081 350.12412 Box - Stuffing - Lip Seal or Packing
100003082 350.12413 Casing - Pump Cent - 6X5X10
100003083 350.12414 Impeller - 10" Dia. Pump Cent.
100003084 350.12427 Ring - Gland Obsolete use 350.12420
100003085 350.12431 Impeller - 11" Dia. Pump Cent.
100003086 350.12434 Slinger - Shaft
100003087 350.12435 Sleeve - Shaft
100003088 350.12438 Packing - Carbon 1/2"
100003099 350.15293 Lantern Ring - 20623
100003124 350.2015 Service Manual
100003125 350.2016 Power End Assembly 100 BHP
100003126 350.20201 Impeller - 14" Dia. Pump Cent. 100 BHP
100003127 350.20501 Impeller 12" Diameter 4 X 4
100003128 350.20502 Casing 4 X 4 X 12
100009363 350.12416 Shaft
100011066 106.54711 Vent - Air - 301370 -1/8 NPT
100011790 350.12422 Mount - Front - STD
100011791 350.12429 Plate - Gland
100011792 350.12432 Frame - Cast Ductile Iron
100011793 350.12433 Key - Square - 1/2 x 1/2 x 3
100011794 350.12439 Strap - Lifting
100012922 70.32916 Nut Hex 3/4-10NC
100012924 70.32992 Nut - Hex Jam - 3.4-10NC
100013017 70.43814 Screw - Hex cap - 3/8-16NC x 1
100013059 70.58955 Washer - Lock 3/8
100013140 70.80603 Seal - Oil - 21159
100013141 70.80612 O-Ring - 70D - 5-1/2 x 5-1/4 x 1/8
100013142 70.80613 Screw - Set 3/4"-10UNC-3A X 3 Cup Point HT Alloy Steel - 40 RC
100013143 70.80614 Screw - Set 3/4"-10UNC-3A X 2 Cup Point HT Alloy Steel - 40 RC
100013720 8.33988 O-Ring - 90D - 4-3/4 x 4-3/8 x 3/16
100014384 350.20106 Ring - Gland - Pump Centrifugal 8x6x14
65
SAP Part #
100015357 7.33684 O-Ring - 70D 2 x 1-7/8 x 1/16 Fluorocarbon
100015436 8.34066 O-ring - 90D - 9-1/4 X 9 X 1/8 -568-270
100016568 26.1 Pipe Plug 1/8 IN. - CI
100016570 26.10102 Plug - Pipe 1/8 Stainless Steel Hex Socket Head
100016573 26.2 Plug - Pipe 1/4 CI
100016593 26.5 Plug - Pipe - 3/4 IN CI
100016601 26.6 Plug - Pipe - 1 IN STL - SQ HD
100020311 68.00102 Coating per spec.
100024706 70.22931 Fitting - Grease - 1/8 45 Deg
100024708 70.22933 Fitting - Grease 1/8 straight
100026448 70.32728 Shaft Slinger
100026525 70.32914 Nut - Hex 1/2-13NC
100026526 70.32915 Nut - Hex 5/8-11NC
100026527 70.32917 Nut Hex 7/8-9NC -PL
100026551 70.32989 Nut - Hex Jam 1/2-13NC
100026553 70.32994 Nut - Hex Jam - 7/8-9UNC - PL
100026632 70.33254 Lock Nut - AN-22
100026847 70.34016 O-ring - 90D - 8-1/4 X 7-3/4 X 1/4 - 568-444
100026855 70.34068 O-ring - 90D - 9-3/4 X 9-1/2 X 1/8 - 568-272
100027498 70.36972 Pipe Plug - 1/4 NPT - Sq. Hd. Steel
100027505 70.36981 Pipe Plug - 1/2 NPT - Sq. Hd. Steel
100028247 70.43381 Hex Socket Screw - 1/2-13NC X 1-1/4
100028455 70.43816 Screw - Hex Cap 3/8-16NC x 1-1/4
100028492 70.43872 Screw- Hex cap -1/2-13NC x 2
100028505 70.43868 Screw - Hex cap - 1/2-13NC x 1-1/2
100028509 70.43895 Screw-Hex Cap - 5/8-11NC X 1-1/4 -PL
100028511 70.43897 Screw - Hex Cap - 5/8-1NC X 1-3/4- Plated
100028512 70.43898 Screw - Hex Cap - 3/4-10NC X 2-1/4 - PL
100028515 70.43903 Screw- Hex cap -5/8-11NC x 2-1/4
100028525 70.43924 Screw - Hex Cap - 3/4-10NC X 2 - PL
100028527 70.43926 Screw - Hex Cap - 3/4-10NC X 2-1/4 - PL
100029874 70.58806 Washer - Flat 3/8
100029924 70.58962 Washer - Lock 5/8" -Steel - Plated
100029925 70.58964 Washer - Lock 3/4 - STL - PL
100029956 70.59086 Lock Washer - W-22
100032333 70.77872 Adapter Hose Cap 9/16-18 JIC Size 6
100032686 70.79319 Adapter - 210292-4S - Brass- 1/4 OD Tube - x 7/16-20 JIC
100033017 70.81033 Roll Pin SS 1/8 x 3/4
100033517 70.83282 Ball Bearing 322S MRC
100033518 70.83283 Seal - Oil - CR 42422 - 4.250B X 5.256OD X.375W
100033519 70.83284 Bearing - Ball - 4.3307 B x 7.8740 OD x 1.4960 W - Single Row - Angular
Contact - 40 Deg Contact Angle - 1/2 PairSKF 7222BAG (7222BECBM per SKF)
100033535 70.83334 O-Ring -70D - 4 1/8 X 4.0 X1/16 568-045
100033536 70.83335 Screw - Set - 7/8-9UNC - 3AX3.0 Cup Point HT Alloy Steel - 40 RC
100033537 70.83337 O-ring - 70D - 3-5/8 X 3-1/2 X 1/16 -568-043
100033545 70.83357 Oil Seal - 42470 - 4.25BX5.26ODX.250W
100034168 70.85981 Adapter - Hose 45 Deg - Brass- 1/4 OD Tube - 1/8 - 27 MPT x 7/16-20 JIC
100035941 70.96714 Adapter Hose 45 Deg 9/16-18 JIC 1/8-27 NPT
100059325 350.12418 Housing - Bearing - Rear
100059327 350.12419 Cap - Bearing - Rear
66
SAP Part #
100059329 350.1242 Ring - Gland
100059330 350.12421 Cap - Bearing - Front
100059333 350.12423 Mount - Rear - STD - Single Hole
100059337 350.12436 Plate - Identification
100059405 350.15318 Mechanical Seal
100059458 350.20101 Impeller - Pump - Centrifugal - 14.375
100059460 350.20104 Sleeve - Shaft Pump - Centrifugal Lip seal 8x6x14
100059461 350.20105 Lantern Ring - 6 Inch OD x 4.75 Inch ID Pump Centrifugal 8x6x14
100059462 350.20108 Packing Set - 6 x 4-3/4 - 4 Rings - Carbon Yarn - Graphite Impregnated - Spec
100059463 350.20110 Strap - Lifting - Pump - Centrifugal 8x6x14 - 300 BHP Power End
100059464 350.20123 Shaft - Pump Centrifugal 8x6x14
100059465 350.20126 Housing - Bearing - Rear - Pump Centrifugal 8x6x14
100059466 350.20127 Mount - Rear - Pump - Centrifugal 8x6x14
100059467 350.20128 Mount - Front - Pump - Centrifugal 8x6x14
100059469 350.20204 Mount - Rear - 8X6X14 - 100BHP
100059470 350.20205 Strap - Lifting - 8 x 6 x 14 Pump
100059471 350.20206 Mount - Front - 8 X 6 X 14 100BHP
100059474 350.20510 Impeller 12" Diameter Coated
100059476 350.20560 Teflon PTFE Lip Seal
101005573 350.20103 Box - Stuffing - Packing - Pump Centrifugal
101014710 350.20107 Plate Gland
101201829 350.20102 Casing - Pump Centrifugal - 8X6X14
101573751 350.20122 Frame - Pump Centrifugal 8x6x14 - 300 HP
101573752 350.20124 Cap - Bearing - Front - Pump - Centrifugal 8x6x14
101573753 350.20125 Cap - Bearing - Rear - Pump - Centrifugal 8x6x14
101646568 350.20501A Impeller 4x4 11.25" Diameter
120133378 350.20202 Adapter - Stuffing Box - 8X6X14 Pump to 100BHP Power end
No SAP 350.20301 Impeller - 14" Dia. Pump Cent.
No SAP 350.20335 Sleeve - Shaft
No SAP 350.20335 Sleeve - Shaft
No SAP 350.2016HD Power End Assembly 300 BHP
67
Section 6
Special Tools
68
Section 7
Addendums
Oil Lube Mechanical Seal Addendum
1. A mechanical seal is standard on the models

350.1241 and 350.1243. It is available as an
option for all other models except the model
350.201.
2. The process fluid lubricates the mechanical

seal, so no external lubrication is required.
3. Install 70.81033 roll pin thru the small hole at

the bottom of the seal cavity. It should extend
3/32” into the seal cavity (Fig. 2, 3 & 4.)
Fig. 1
Fig. 3 Fig. 4
Fig. 2
4. Install the stationary side of the mechanical into the bore of the seal cavity.
CAUTION: make sure the notch in the back side of the stationary seal is aligned
with the roll pin. Use a soapy water or alcohol hand sanitizing solution to aid in
installtion. Use the cardboard divider supplied with the new seal (to protect the seal
face), press the stationary seal face into the bore until it bottoms out and the o-ring
is seated.
69
5. Turn the seal head over and install spacer (BHPS 700141)
instead of the standard packing ring. (Fig. 5)
Fig. 5
6. Install seal (70.80607) with the spring facing the spacer Fig. 6
using the appropriate seal driver. (Fig. 6)
7. Make sure seal is seated against the spacer and the back
of the seal flush with the stuffing box. (Fig. 7)
Fig. 7
8. Install gland plate (350.12429) and hand tighten the

socket head cap screws (70.43374) If using torque
wrench, tighten to between 100 – 120 in. oz. or 6.25 – 7.5
in. lbs. ( DO NOT OVER TIGHTEN. (Fig. 8 & 9)
Fig. 8
9. Oil is supplied to the seal by a sealed tank system or a

small oil bottle (Fig. 10)
Fig. 9
70
Fig. 10
10. Install shaft sleeve (350.12435). (Fig. 12)
Fig. 12
11. Carefully install seal head (350.12411) assembly onto the
power frame (350.2016). (Fig. 13)
12. Spray seal both faces with WD-40 or similar product to

make sure they are free of contaminants.
Fig. 11 Fig. 13
71
13. Using a soapy water or alcohol hand sanitizing solution to aid
in installtion, slide rotating half of the mechanical seal over
the sleeve until the faces meet. Be careful not to “slap” the
faces together or they could be damaged. Use caution so as
not to cause the rubber bellows to “curl” while pressing the
rotating half into position. CAUTION – Do not use oil, grease Fig. 14
or other lubicants to slide rotating half of seal on to the
sleeve unless they are specifically designed for that purpose.
Oil or grease may cause the rubber bellow to slip on the shaft
during operation causing the seal to leak. (Fig. 14)
14. Install the retaining spring. (Fig. 15)
Fig. 15
15. Coat O-ring grove with Never-Seize or grease and install

impeller O-ring (70.80608) in O-ring groove on back side of
impeller (350.12414, 350.12431, 350.20501). Never-Seize or
grease will hold o-ring in place during impeller installation
(Fig. 16 ). Fig. 16
16. Install impeller impeller and adjust per instruction on page

29. (Fig. 17)
Fig. 17
72
17. Seal installation can be facilitated by the use of a seal installation tool. (Fig. 18 ) It
can be fabricated per the drawing Fig. 19. The tool is usefull during installation and
removal of both the stationary and rotating halves of the seal.
Fig. 18
Fig. 19
73
Section 8
Notes
74
Oilfield Service Applications
. Blending
. Cementing
. Fracturing
. Charge Pumps
. Drilling Mud
General Industrial
. Waste Water Treatment
Sludge Slurry Applications
. Drilling Mud
. Sewage Sludge
. Lime
. Industrial Waste
. Hydromulch
. Sand & Silt Laden Water
88 South C Street - Duncan, OK. 73533 – USA

Phone: 800-375-9470 Email: pumps@blackhawkid.com
www.BHID.com
75

Blackhawk Pump Manual 2018

Uploaded by

Copyright:

Available Formats

Blackhawk Pump Manual 2018

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Blackhawk Pump Manual 2018

Uploaded by

Copyright:

Available Formats

Maintenance and Operations Manual

Special Tools…….…………………………. Section 6

*Contact BlackHawk Pumps& Services for applications in excess of 100 HP.

Warning: Before attempting to service the pump…..

WARNING: BEFORE STARTING PUMP

All Pumps are Right-Hand Rotation Units –

FAILURE TO PERFORM THE ABOVE WILL VOID

(Figure 1) Parallel (Figure 2) Angular

Maximum RPM and Allowable Misalignment - Inch

Suction piping should

Priming the Pump –

Model 350.201, 350.202, 350.203 – 1800 RPM

(Please consult manufacturer if these speeds need to be

Operating Guidelines for the Pump –

Disassembling the Pump

2. Attach lifting bail to pump discharge flange

3. Remove retaining nuts (70.32916) and jam

4. Place shaft wrench over pump shaft (Fig. 3)

7. Remove inboard bearing cap (350.12421)

8. Place rotating assembly face down and

9. Lift rear bearing housing, bearings and

10. Remove rear bearing cap (350.12419).

11. Remove bearing retaining lock nut

12. Use a bearing press to remove bearings

2. Install lock washer (70.09111) and

4. Install shaft and bearing assembly in rear

5. Slide rear bearing cap assembly

7. Install inboard bearing (70.80602) on

8. Carefully lower shaft and bearing

9. Install 1/2"-13 jam nut (70.32989) on

10. Install lip seal (70.80604) with lip facing

11. Install lip seal (70.80603), with lip facing

12. Lift power frame assembly and with

14. Install front bearing cap assembly over

16. Install shaft sleeve O-ring (70.80609), over

18. Install lantern ring set (350.15293)

19. Install one Buna-N lip seal

20. Install ring gland (350.12427) with

21. Install gland plate (350.12429) using

22. Tighten cap screws (70.43374)

23. Install 1/8" pipe plugs (26.1) using

25. Install one each 5/8-11NC x 1-3/4" cap

26. Install balance of four each 5/8-11NC x 1-3/4" cap

27. Install O-ring (70.34019) in groove in stuffing box

28. Coat O-ring grove with Never-Seize or grease

29. Install shaft wrench over keyed end of shaft.

31. Adjust clearance behind impeller using .014

32. Carefully tighten lock nuts on bearing housing

33. Using lifting eye and hoist position pump

37. Install lifting strap (Fig. 41).

38. Using .016 inch feeler gauge, adjust

2. The process fluid lubricates the mechanical seal,

3. Install 70.81033 roll pin thru the small hole at

7. Install gland plate (350.12429) and hand tighten the

8. Install shaft sleeve (350.12435). (Fig. 9) Fig. 8

9. Carefully install seal head (350.12411) assembly onto

11. Using a soapy water or alcohol hand sanitizing solution

12. Install the retaining spring . (Fig. 12)

14. Install impeller impeller and adjust per instruction on