Republic of the Philippines

DEPARTMENT OF EDUCATION
Region XII

FIRST QUARTER EXAM IN TVE 8 (CARPENTRY)

MULTIPLE CHOICE. Choose the letter of the correct answer. Write your answer on your answer
sheet.

1. What kind of chisel has an upper part shaped like a hollow cone in which
the handle is set?

A. Beveled chisel C. Socket chisel

B. Ordinary flat chisel D. Tang firmer chisel

2. What tool has a steel blade sharpened to a cutting edge and held firmly
in place by a wooden handle?

A. chisel C. Spokeshave
B. Iron smooth plane D. Wooden smooth plane

3. Which of the following tools is used to mark lines along the grain of wood or to
indicate the desired width and thickness of wood?

A. Chalk line C. Metal rule

B. Marking gauge D. Pencil

5. What kind of tool is used in driving and pulling-out nails?

A. ballpen hammer C. crow bar

B. claw hammer D. sledge hammer

6. What is used for marking line in equal distances along the edge of wood?

A. compass C. marking gauge

B. divider D. pencil

7. What kind of tool is used for roughing off surfaces?

A. chisel C. gouge
B. file D. rasp

8. What kind of tool is used to drive screws into wooden surfaces?

 A. claw hammer C. screwdriver
B. hand drill D. wrench

9. What refers to lumbers that are dressed in four sides?

A. molding C. rough lumber

B. S4S D. Tongue and groove

10. What do you call to a board installed on the exterior part of a building to protect
the building from bad weather condition?
A. Baseboard C. Molding
B. Floor board D. Siding wood board

11. Which of the following refers to an embellishment in strip form made of wood that
is used to decorate or to finish a surface such as walls of a room?
A. Baseboard C. Molding
B. Handrail D. Siding wood board

12. What kind of material is commonly used while ascending or descending

stairways and escalators in order to prevent injurious falls?

A. Handrail C. Siding wood board

B. Molding D. S4S

13.Which of the following bolts expands when inserted in the hole when the
nut is tightened?
A. carriage bolt
B. expansion bolt
C. machine bolt
D. stud bolt
14. What mechanism is used to open or close a door?
A. barrel bolt C. hasp
B. door knob D. hinge

15. Which of the following kinds of accessories is fixed to the side of the drawer and
in the carcass of the drawer unit?
A. Catches
B. Drawer handle
C. Drawer slide
D. Mounting bracket
 16. Which of the following is a list of all things needed in a project together with
theirdescriptions, sizes and prices?
A. Damage report form C. Maintenance form
B. Inventory form D. Request form
17. Which of the following parts of a request formtells the amount of materials to be
purchased?
A. Description C. Unit
B. Quantity D. Unit cost
18. What gives the measure of materials to be purchased?
A. Description C. Unit
B. Quantity D. Unit cost
19. What part of the request form states the detailed names of materials?
A. Amount C. Quantity
B. Description D. Unit cost
20. What gives the price of each material?
A. Amount C. Quantity
B. Description D. Unit cost
21. What refers to the cost of all materials?
A. Amount C. Quantity
B. Description D. Unit cost
22. What is the first procedure in requesting tools and materials?
A. Write the number of available materials.
B. List the unit of materials to be requisitioned .
C. Fill in the classification of the project and its purpose.
D. State the name of the project and date when you requested for materials.
23. Which of the following is the fifth procedure in requesting tools and materials?
A. Write your name as requisitioner.
B. List the cost per unit and the total cost.
C. Enumerate the materials with their description.
D. Secure the approval of authorities concerned .

24. What is the last procedure in requesting tools and materials?

A. Write the number of available materials.
B. List the cost per unit and the total cost.
C. Enumerate the materials with their description.
D. Secure the approval of authorities concerned .
25. Why is it necessary to inspect the tools and materials before receiving
it?
A. to lessen the quantity of materials
B. tominimize the cost of materials
C. to determine defective tools and materials
D. to avoid unnecessary tools and materials

26. What classification of tools can be used after a period of time?

A. condemned
B. functional
C. non-functional
D. repaired
27. What classification of tools is considered condemned?
A. condemned
B. functional
C. non-functional
D. to be repaired
28. What do you call to the process of putting a tag on a defective tool to avoid using
it?
A. labelling
B. signing
C. posting
D. pricing
29. What is the process of checking the list of tools and equipment in the shop?
A. Inventory
B. Labelling
C. Requesting
D. Tagging
30. What is the process of reshaping the cutting edge of a tool?
A. grinding
B. honing
C. jointing
D. whetting
31. What is the process of sharpening edge tools with water on a waterstone and oil
in an oilstone using the coarse side?
A. grinding
B. honing
C. jointing
D. whetting
32. What is the process of sharpening edge cutting tools after whetting?
A. grinding
B. honing
C. jointing
D. whetting
33. What is done by running a flat file over the ends of saw teeth?
A. filing
B. honing
C. jointing
D. setting

34. What is the process of bending the teeth of the saw slightly outward?
A. filing
B. honing
C. jointing
D. setting
35. What is the actual sharpening of the teeth of a saw?
A. filing
B. honing
C. jointing
D. setting
36. What kind of tool is used in setting the teeth of asaw?
A. file
B. plier
C. saw set
D. wrench
37. What kind of tool is used in sharpening the teeth of a saw?
A. file
B. plier
C. saw set
D. wrench
38. What is a substance introduced between two moving surfaces to reduce friction?
A. alcohol
B. lubricant
C. sealant
D. water
39. What is derived from wool grease and is safe alternative to the more common
petro-chemical based lubricants?
A. lanolin
B. mineral oil
C. vegetable oil
D. water

40. What is used to encompass lubricating base oil derived from crude oil?
A. Lanolin
B. mineral oil
C. vegetable oil
D. water
41. What is used to measure long distances available from 3.00m to 7.5 meters
long?

A. Extension rule C. Push-pull rule

B. Measuring tape D. Zigzag rule
 42. What kind of rule is available from (4ft) 1.20m to (6ft) 1.80m commonly used by
carpenters for rough layout?

A. Caliper C. Push-pull rule

B. Measuring tape D. Zigzag rule

43. Which of the following kinds of rule is used for measuring inside distances such
as rooms, windows and cabinets?

A. Extension rule
B. Measuring tape
C. Push-pull rule
D. Zigzag rule

44. What is used for measuring outside diameter of cylindrical objects?

A. Caliper C. Push-pull rule

B. Measuring tape D. Zigzag rule

45. What measuring tool is used to measure longer distances from 25 meters to 100
meters long?

A. Extension rule
B. Measuring tape
C. Push-pull rule
D. Zigzag rule

46. What is the system of measurement that uses inch, foot and yard?

A. Decimal system C. Metric system

B. English system D. System international

47. What is the system of measurement that uses millimeter (mm), centimeter (cm), meter
(m) and kilometer (km)?

A. Decimal system C. Metric system

B. English system D. System international

48. In conversion of linear measurements, how many inches is one meter?

 A. 29.37 inches C. 39.37 inches
B. 36.37 inches D. 40 inches

49. How many inches are two feet?

A. 6 inches C. 18 inches
B. 12 inches D. 24 inches

50. How many feet is one meter?

A. 2.281 feet C. 3.182 feet

B. 3.281 feet D. 3.30 feet

51. What is the formula in computing the area of a triangle?

A. Area = base x height

B. Area = ½ base x height
C. Area = length x width
D. Area = ½ length x width
52. What is the very light line used to block an object?
A. Object line B. Border line C. Constructionline D. Visible line

53. What are extra heavy lines used to frame a drawing?

A. Object line B. Border line C. Hidden line D. Visible line

54. What are short broken dashes that represent the hidden part of an object which
needs to be shown?

A. Object line B. Border line C. . Hidden line D. Visible line

55. What are very distinct lines that show the visible portions of an object?

A. Object line B. Border line C. . Hidden line D. Visible line

56. What are thin, long or short dashes that indicate the center of any symmetrical
figure?

A. Object line B. Center line C. Extension line D. Visible line

57. What is caused by a poor working attitude?

 A. carelessness
B. damage to property
C. malingering
D. misbehavior
58. What is placed in the construction area to prevent the workers from passing
restricted areas?
A. Barricade
B. Caution sign
C. Danger sign
D. Exit sign
59. What must be used when workers are at risk from flying particles, liquid
chemicals, acids or caustic liquids, chemical gasses or vapors?
A. ear muffs
B. gloves
C. goggles
D. hard hat
60. What kind of PPE is required when working around nails, wire, tacks, scrap
metals and other objects that could pierce the feet?
A. body protection
B. face protection
C. foot protection
D. hand protection
61. What must be worn to protect the construction worker from falling while working
on high altitude?
A. face mask
B. hard hat
C. harness
D. respirator
62. What kind of PPE is worn if it is not possible to ventilate the work area properly
like painting on a closed area?
A. face mask
B. goggle
C. respirator
D. safety shoes
63. What means the arrangement of necessary items in good order for use?
A. Seiri B. Seiton C. Shiketsu D. Shitsuke
64. What is the action to identify and eliminate all necessary items from your
workplace?
A. Seiri B. Seiton C. Shiketsu D. Shitsuke
65. What is the condition where high standard of good housekeeping is maintained
so that there is no dust and rust everywhere?
A. Seiso B. Seiton C. Seiketsu D. Shitsuke

66. It is simply the application of workable principles that increases the awareness
and ability of the workers to be more productive and efficient without sacrificing their
safety and the product quality.

A. Occupational Health & Safety B. Risk Management

C. Work Procedure D. Work Simplification

67. Which primarily uses least resources in the workplace?

A. Occupational Health & Safety B. Risk Management

C. Work Procedure D. Work Simplification
68. What government agency is responsible primarily for setting and enforcing
mandatory occupational health and safety standards through appropriate orders?

A. Department of Public Works and Highways B. Civil Service Commission

C. Department of Labour and Employment D. Department of Budget and

Management

69. Which is NOT a PPE?

A. helmets B. goggles
C. gloves D. shorts

70. Which is a common hazard?

A. obstructions B. damaged saw blades

C. hazardous dusts D. all of the above
--------------------------------------G O D B L E S S -----------------------------------------