CONSTRUCTION NOTES

A. GENERAL
1. CONSTRUCTION NOTES AND TYPICAL ANCHORAGE LENGTH) UNLESS E. MASONRY CONCRETE BLOCKS H588x300 I-BEAM
WEB THICKNESS =24MM
DETAILS APPLY TO ALL DRAWINGS OTHERWISE SHOWN ON DRAWINGS, 1. ALL NON-LOAD BEARING TYPE CONCRETE FLANGE THICKNESS = 42MM
UNLESS OTHERWISE SHOWN OR SPLICES SHALL BE STAGGERED BLOCKS SHALL HAVE A UNIT WEIGHT NOT TO COLUMN

NOTED. MODIFY TYPICAL DETAILS AS WHENEVER POSSIBLE. EXCEED 80 PCF. FOR LOAD BEARING TYPE 10-25MMØ ANCHOR
DIRECTED TO MEET SPECIAL 7. ALL ANCHOR BOLTS, DOWELS, AND CONCRETE BLOCKS, A MINIMUM BOLTS 800MM LONG
WITH HEX DOUBLE NUTS
CONDITIONS. OTHER INSERTS SHALL BE PROPERLY COMPRESSIVE STRENGTH OF 8.28 MPA (1200

400
2. SHOP DRAWINGS WITH ERECTION AND POSITIONED AND SECURED IN PLACE PSI) SHALL BE DEVELOPED.
PLACING DIAGRAMS OF ALL PRIOR TO PLACING OF CONCRETE. 2. PROVIDE 1 - Ø 16 EXTRA VERTICAL BARS AT N.G.L
STRUCTURAL STEEL, MISCELLANEOUS 8. CONTRACTOR SHALL NOTE AND CORNERS, INTERSECTIONS, END OF WALLS,
IRON, PRE-CAST CONCRETE ETC. PROVIDE ALL MISCELLANEOUS AND EACH SIDE OF OPENINGS AS SHOWN.
SHALL BE SUBMITTED FOR ENGINEER'S CURBS, SILLS, STOOLS, EQUIPMENT, 3. LINTEL BEAMS OR LINTEL BLOCKS SHALL BEAR
APPROVAL BEFORE FABRICATION. AND MECHANICAL DRAWINGS. AT LEAST 8 INCHES (200 MM) ON EACH SIDE
3. CONTRACTOR SHALL VERIFY ALL 9. ALL CONCRETE SHALL BE KEPT MOIST OF MASONRY WALL OPENING.
DIMENSIONS BEFORE ALL WORK IS TO FOR A MINIMUM OF SEVEN (7) 4. 4. WALL REINFORCEMENTS SHALL BE AS
BEGIN, CHECK WITH MECHANICAL CONSECUTIVE DAYS IMMEDIATELY FOLLOWS:
AND ELECTRICAL CONTRACTORS FOR AFTER POURING BY THE USE OF WET
CONDUITS, PIPE SLEEVES, ETC. TO BE BURLAP, FOG SPRAYING, CURING VERTICAL HORIZONTAL

3000
WALL THICKNESS 16-20MMØ VERTICAL
EMBEDDED IN CONCRETE. COMPOUNDS OR OTHER APPROVED REINFORCEMENT REINFORCEMENT BARS
4. IT SHALL BE THE CONTRACTOR'S METHODS. 10MMØ COLUMN TIES
8 in. (200 mm) 12 Ø @ 600 mmØ 10 Ø @ 600 mm
RESPONSIBILITY TO PROVIDE 10. STRIPPING OF FORMS AND SHORES: SPACED AT
ADEQUATE SHORING AND BRACING
Pedestal Columns 24 hours 6 in. (150 mm) 10 Ø @ 600 mmØ 10 Ø @ 600 mm
OF THE STRUCTURE FOR ALL LOADS
Suspended Slab except when TOP BARS ALONG "Y"
THAT MAYBE IMPOSED DURING additional loads are imposed
8 days
4 in. (100 mm) 10 Ø @ 600 mmØ 10 Ø @ 600 mm
CONSTRUCTION. Walls 18 hours
20MMØ TEMP BARS
TOP BARS ALONG "X"

B. CONCRETE REINFORCEMENT Beams 14 days

1. ALL MATERIALS AND WORKMANSHIP STRUCTURAL NOTES

SHALL CONFIRM WITH THE LATEST C. CAMBER REQUIREMENTS

500
BUILDING CODE OF AMERICAN 1. UNLESS OTHERWISE NOTED ON THE 1. SEE TABLE OF LAP SPLICE AND ANCHORAGE
CONCRETE INSTITUTE (ACI-318). PLANS OR SPECIFICATIONS, CAMBER LENGTHS SHOWN ON SHEET BOTTOM BARS ALONG "Y"
2. ALL CONCRETE SHALL DEVELOP A ALL R.C. BEAMS AT LEAST 10 MM 2. LAP SPLICE SHALL BE LOCATED ONLY WITHIN THE
MINIMUM COMPRESSIVE STRENGTH AT FOR EVERY 4000 MM OF CLEAR LAP SPLICE ZONE
THE END OF TWENTY-EIGHTY (28) DAYS SPAN EXCEPT CANTILEVERS WHICH 3. CLOSED HOOPS WITH A 135° BEND SHALL BE
S E C T I O N BOTTOM BARS ALONG "X"

WITH CORRESPONDING MAXIMUM SHALL BE 50 MM FOR EVERY 3000 SPACED AT 100mm ON CENTER MAXIMUM AT A
SIZE AGGREGATE AND SLUMPS AS MM OF CLEAR SPAN. DISTANCE 3d FROM THE FACE OF THE SUPPORT,
FOLLOWS: 2. UNLESS OTHERWISE NOTED IN PLANS FIRST STIRRUP SHALL 5d FROM THE FACE OF THE 2700

28 DAYS MAX. SIZE OR SPECIFICATIONS, CAMBER ALL SUPPORT

LOCATION MAX. SLUMP R.C. BEAMS 8 MM PER 3000 MM OF
STRENGTH AGGREGATE 4. SPACING OF STIRRUPS ON LAP SPLICE SHALL BE
Curbs & Slab On SHORTER SPAN AND 14 MM FOR SPACED 100mm ON CENTER MAXIMUM
3000 psi 1 in. (25 mm) 4 in. (100 mm)
Grade EVERY 2000 MM OF SLABS 5. AT INTERIOR SUPPORT (CONTINUOUS END) PROVIDE
Foundation 4000 psi 3/4 in. (19 mm) 6 in. (150 mm) CANTILEVER SPAN. LARGER SIZE AND NUMBER OF TOP AND BOTTOM
Column Foundation
4000 psi 3/4 in. (19 mm) 6 in. (150 mm)
BARS FROM ADJACENT SPANS
to Roof D. FOUNDATION 6. NO SPLICE SHALL BE ALLOWED 2d FROM THE FACE
Suspended Slabs / 1. FOUNDATION IS DESIGNED USING OF THE SUPPORT
4000 psi 3/4 in. (19 mm) 6 in. (150 mm)
Beams ALLOWABLE SOIL BEARING
CAPACITY OF 2000 PSF (100 KPA) AS H588x300 I-BEAM
WEB THICKNESS =24MM
3. ALL REINFORCING BARS SHALL PER CLIENT. FLANGE THICKNESS = 42MM
CONFORM TO ASTM A615 GRADE 40 2. FOUNDATION SHALL REST ON 700 COLUMN
FOR DIAMETER 12 AND SMALLER BARS NATURAL SOIL. UNLESS OTHERWISE
CL °
AND GRADE 40 FOR DIAMETER 16 NOTED BY THE ENGINEER, NO PART H588x300 I-BEAM
135

AND LARGER BARS. OF THE FOUNDATION SHALL REST ON 20-20MMØ VERTICAL WEB THICKNESS =24MM 12-25MMØ ANCHOR

6d
b
FLANGE THICKNESS = 42MM
4. IN GENERAL, THE LATEST EDITION OF FILL. BARS BOLTS 800MM LONG

2700

400
COLUMN WITH HEX NUTS
ACI-315, MANUAL OF STANDARD 3. THE CONTRACTOR SHALL NOTIFY THE

SEE SCHEDULE
PRACTICE DETAILING REINFORCED ENGINEER AFTER FOOTING db

D
CONCRETE STRUCTURES SHALL BE EXCAVATION HAVE BEEN
ADHERED TO, UNLESS OTHERWISE COMPLETED AND PRIOR TO
SHOWN OR NOTED. CONCRETING TO CONFIRM THE I.D = 4db

EQUAL
5. MAINTAIN MINIMUM CONCRETE DESIGN SOIL BEARING CAPACITY. 25MM THK BASEPLATE

COVER FOR REINFORCING STEEL AS 4. BLOCK WALL REINFORCING BARS 60MM CLEAR TO
VERTICAL TIES TYPICAL
FOLLOWS: SHALL BE LAPPED A MINIMUM OF 30
12-25MMØ ANCHOR
Suspended Slabs 3/4 in. (19 mm) BAR DIAMETERS WHERE SPLICED, BOLTS 800MM LONG
HORIZONTAL / VERTICAL DOWELS WITH HEX NUTS
Slab on Grade 1 1/2 in. (38 mm)

EQUAL
FROM FOOTINGS, COLUMNS /
Where concrete is exposed to earth but 2 in. (50 mm) COLUMN TIES
poured against forms WALLS OR SLABS SHALL EXTEND INTO
Where concrete is deposited directly against 3 in. (75 mm)
THE BLOCK WALL A MINIMUM IF 30
earth BAR DIAMETERS OR A
REINFORCEMENT OF WALL. P L A N
5. ALL CELLS CONTAINING
6. SPLICES SHALL BE SECURELY WIRED REINFORCING BARS OR INSETS
TOGETHER AND SHALL LAP OR EXTEND
IN ACCORDANCE WITH TABLE 1
(TABLE OF LAP SPLICE AND
SHALL BE SOLIDLY FILLED WITH
CONCRETE GROUT (REFER TO A PEDESTAL COLUMN DETAILS
NOT TO SCALE
SPECIFICATIONS).
PRC Reg. No.: PROJECT NAME: OWNER SHEET CONTENTS:

CONSTRUCTION NOTES
PROPOSED SIX-STOREY SCHOOL BUILDING STRUCTURAL NOTES
PTR. No.:
PEDESTAL COLUMN DETAILS
ALL MEASUREMENTS ARE TO BE VERIFIED ON SITE BY
ALPHA OMEGA DESIGN AND BUILD SERVICES CO. S-1
EINSTEIN ACADEMY - NURSERY TO GRADE 7
3 MS. HONGLIFEI CHEN ALL DISCREPANCIES ARE TO BE IMMEDIATELY REPORTED TO
ARCHITECTS AND PROJECT MANAGERS. CONTRACTORS ARE TO
PLACE of ISSUE:
ENGINEER #9 ARTY II TALIPAPA QUEZON CITY PREPARE AND SUBMIT SHOP DRAWINGS TO ARCHITECTS PRIOR TO
C O M M E N C E M E N T O F W O R K S . T H I S D RA W I N G A C T I N G A S
INSTRUMENT OF SERVICE IS THE PROPERTY OF THE ARCHITECT &
TOTAL SHEETS:

LOCATION: CANNOT BE REPRODUCED W/OUT THEIR WRITTEN CONSENT.

DATE of ISSUE: ADDRESS DRWN/REV BY: REVISE : 002
CIVIL ENGINEER #93 Lot
Blk ARTY II TALIPAPA
5A Marigold QUEZON
Street, Talipapa CITY
Quezon City #9 ARTY II TALIPAPA QUEZON CITY
- REPUBLIC ACT No. 9266
FILENAME: