Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 7 views

    Assembling The Carburetor

    Uploaded by

    PHUONG NGUYEN
    The document provides instructions for assembling a carburetor in 6 steps: 1) Install the main nozzle and jet. 2) Install the pilot jet and cap. 3) Install the needle valve, float, float pin, and tighten the float screw. 4) Install the new gasket, float chamber, and tighten the screws. 5) Install the new O-ring and tighten the drain screw. 6) Install the plates, rubber seals, cover, and tighten the cover screws.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Assembling The Carburetor

    Uploaded by

    PHUONG NGUYEN
    7 views1 page
    The document provides instructions for assembling a carburetor in 6 steps: 1) Install the main nozzle and jet. 2) Install the pilot jet and cap. 3) Install the needle valve, float, float pin, and tighten the float screw. 4) Install the new gasket, float chamber, and tighten the screws. 5) Install the new O-ring and tighten the drain screw. 6) Install the plates, rubber seals, cover, and tighten the cover screws.

    Original Title

    083

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for assembling a carburetor in 6 steps: 1) Install the main nozzle and jet. 2) Install the pilot jet and cap. 3) Install the needle valve, float, float pin, and tighten the float screw. 4) Install the new gasket, float chamber, and tighten the screws. 5) Install the new O-ring and tighten the drain screw. 6) Install the plates, rubber seals, cover, and tighten the cover screws.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    7 views1 page

    Assembling The Carburetor

    Uploaded by

    PHUONG NGUYEN
    The document provides instructions for assembling a carburetor in 6 steps: 1) Install the main nozzle and jet. 2) Install the pilot jet and cap. 3) Install the needle valve, float, float pin, and tighten the float screw. 4) Install the new gasket, float chamber, and tighten the screws. 5) Install the new O-ring and tighten the drain screw. 6) Install the plates, rubber seals, cover, and tighten the cover screws.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Carburetor

    Assembling the carburetor 4. Install the new gasket 9, float chamber


    1. Install the main nozzle 1 and main jet 2. 0, and then tighten the float chamber
    screws q.
    2. Install the pilot jet 3 and cap 4.

    2
    5. Install the new O-ring w, and then tight-
    en the drain screw e to specified torque. 1
    1 4

    9
    2
    e
    w

    0 3
    68840050

    4
    q
    q 68840070
    3. Install the needle valve 5 to the float 6,
    then install the float pin 7 into the float
    6, and then tighten the float screw 8. 6. Install the plate 1 r, rubber seal 1 t,
    plate 2 y, rubber seals 2 u, cover i,

    6
    8
    and then tighten the cover screws o.

    o o
    i
    5
    7

    6
    u u
    5 t y
    r

    68840060
    7
    68840080

    8
    9
    6885J11 4-14

    You might also like