LAMP

A1394B/3SYG/S530-E2

Features
•Low power consumption

•High efficiency and low cost

•Good control and free combinations on the colors of LED lamps

•Good lock and easy to assembly.

•Stackable and easy to assembly

•Stackable vertically and easy to assembly

•Stackable horizontally and easy to assembly

•Versatile mounting on P.C board or panel

•The product itself will remain within RoHS compliant version

• Compliance with EU REACH

• Compliance Halogen Free .(Br <900 ppm ,Cl <900 ppm , Br+Cl < 1500 ppm)

Description
•ARRAY=Plastic Holder+ Combinations of Lamps.
•The array will easily mount the applicable lamps on any panel up to.

Applications
•Used as indicators of indicating the Degree, Functions, Positions etc, in electronic instruments

1 Copyright
Revision :2 © 2010, Everlight All Rights Reserved. Release Date : Dec.08 . 2014. IssueRelease Date:2014-12-10
No: DAE-0000150_Rev.2 09:55:17.0
www.everlight.com
LifecyclePhase: Expired Period: Forever
 DATASHEET
LAMP
A1394B/3SYG/S530-E2

Device Selection Guide

Chip
PART NO. Emitted Color Resin Color
Materials

264-10SYGD/S530-E2-L AIGaInP Brilliant Yellow Green Green Diffused

Absolute Maximum Ratings (Ta=25℃)

Parameter Symbol Rating Unit

Continuous Forward Current IF SYG 25 mA

Peak Forward Current (Duty 1/10 @ 1KHZ) IFP SYG 60 mA
Reverse Voltage VR 5 V
Power Dissipation Pd SYG 60 mW
Operating Temperature Topr -40 ~ +85 ℃
Storage Temperature Tstg -40 ~ +100 ℃
Soldering Temperature Tsol 260 ℃ for 5 sec.

Electro-Optical Characteristics (Ta=25℃)

Conditi
Parameter Symbol Min Typ Max Unit
on
Forward Voltage VF SYG 1.7 2.0 2.4 V IF=20mA

Reverse Current IR SYG ---- ---- 10 uA VR=5V

Luminous Intensity IV SYG 25 50 ---- mcd IF=20mA

Viewing Angle 2θ1/2 SYG ---- 60 ---- deg IF=20mA

Peak Wavelength λp SYG ---- 575 ---- nm IF=20mA

Dominant Wavelength λd SYG ---- 573 ---- nm IF=20mA

Spectrum Radiation Bandwidth △λ SYG ---- 20 ---- nm IF=20mA

2 Copyright
Revision :2 © 2010, Everlight All Rights Reserved. Release Date : Dec.08 . 2014. IssueRelease Date:2014-12-10
No: DAE-0000150_Rev.2 09:55:17.0
www.everlight.com
LifecyclePhase: Expired Period: Forever
 DATASHEET
LAMP
A1394B/3SYG/S530-E2

Typical Electro-Optical Characteristics Curves

SYG
Relative Intensity vs. Wavelength (Ta=25℃) Directivity (Ta=25℃)
Relative Intensity (a.u.)

Radiation Angle
Wavelength (nm) Relative Intensity (a.u.)
Forward Current vs. Forward Voltage (Ta=25℃) Relative Intensity vs. Forward Current (Ta=25℃)
1.5
Relative Intensity(a.u.)
Forward Current (mA)

1.0

0.5

0.0
0 5 10 15 20 25
Forward Voltage (V) Forward Current (mA)
Relative Intensity vs. Ambient Temp. Forward Current vs. Ambient Temp.

2.0 40
Relative Intensity(a.u.)

Forward Current (mA)

1.5 30

1.0 20

0.5 10

0.0 0
25 30 35 40 45 50 55 60 65 70 0 20 40 60 80 100

Ambient Temperature Ta(℃) Ambient Temperature Ta(℃)

3 Copyright
Revision :2 © 2010, Everlight All Rights Reserved. Release Date : Dec.08 . 2014. IssueRelease Date:2014-12-10
No: DAE-0000150_Rev.2 09:55:17.0
www.everlight.com
LifecyclePhase: Expired Period: Forever
 DATASHEET
LAMP
A1394B/3SYG/S530-E2

Package Dimension

Note: Note:
1. All dimensions are in millimeters, tolerance is 0.25mm except being specified
2. Lead spacing is measured where the lead emerge from the package.

4 Copyright
Revision :2 © 2010, Everlight All Rights Reserved. Release Date : Dec.08 . 2014. IssueRelease Date:2014-12-10
No: DAE-0000150_Rev.2 09:55:17.0
www.everlight.com
LifecyclePhase: Expired Period: Forever
 DATASHEET
LAMP
A1394B/3SYG/S530-E2

Moisture Resistant Packing Materials

Label Explanation
‧CPN: Customer’s Production Number
‧P/N : Production Number
Pb EVERLIGHT X
‧QTY: Packing Quantity
‧CAT: Ranks of Luminous Intensity
‧HUE: Ranks of Dominant Wavelength
‧REF: Ranks of Forward Voltage
RoHS ‧LOT No: Lot Number
A1394B/3SYG/S530-E2

Packing Specification
■Anti-electrostatic Plate ■ Inner Carton ■ Outside Carton

■ Packing Quantity
1. 160 PCS/1 Plate, 4 Plates/1 Inner Carton
2. 10 Inner Cartons/1 Outside Carton

5 Copyright
Revision :2 © 2010, Everlight All Rights Reserved. Release Date : Dec.08 . 2014. IssueRelease Date:2014-12-10
No: DAE-0000150_Rev.2 09:55:17.0
www.everlight.com
LifecyclePhase: Expired Period: Forever
 DATASHEET
LAMP
A1394B/3SYG/S530-E2

Notes
1. Lead Forming
 During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb.
 Lead forming should be done before soldering.
 Avoid stressing the LED package during leads forming. The stress to the base may damage the LED’s characteristics or it
may break the LEDs.
 Cut the LED lead frames at room temperature. Cutting the lead frames at high temperatures may cause failure of the LEDs.
 When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead position of the LED. If the LEDs
are mounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the LEDs.

2. Storage
 The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from Everlight and the storage life limits
are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a
nitrogen atmosphere and moisture absorbent material.
 Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can
occur.

3. Soldering
 Careful attention should be paid during soldering. When soldering, leave more then 3mm from solder joint to epoxy bulb,
and soldering beyond the base of the tie bar is recommended.
 Recommended soldering conditions:
Hand Soldering DIP Soldering
Temp. at tip of iron 300℃ Max. (30W Max.) Preheat temp. 100℃ Max. (60 sec Max.)
Soldering time 3 sec Max. Bath temp. & time 260 Max., 5 sec Max
Distance 3mm Min.(From solder Distance 3mm Min. (From solder
joint to epoxy bulb) joint to epoxy bulb)
 Recommended soldering profile

laminar wave

Fluxin

Preheat

 Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering.
 Dip and hand soldering should not be done more than one time

6 Copyright
Revision :2 © 2010, Everlight All Rights Reserved. Release Date : Dec.08 . 2014. IssueRelease Date:2014-12-10
No: DAE-0000150_Rev.2 09:55:17.0
www.everlight.com
LifecyclePhase: Expired Period: Forever
 DATASHEET
LAMP
A1394B/3SYG/S530-E2

 After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until the LEDs return to
room temperature.
 A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature.
 Although the recommended soldering conditions are specified in the above table, dip or hand soldering at the lowest
possible temperature is desirable for the LEDs.

 Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder
wave.

4. Cleaning
 When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than
one minute. Dry at room temperature before use.
 Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs
depends on factors such as ultrasonic power and the assembled condition. Ultrasonic cleaning shall be pre-qualified to
ensure this will not cause damage to the LED

5. Heat Management
 Heat management of LEDs must be taken into consideration during the design stage of LED application. The current
should be de-rated appropriately by referring to the de-rating curve found in each product specification.
 The temperature surrounding the LED in the application should be controlled. Please refer to the data sheet de-rating
curve.

6. ESD (Electrostatic Discharge)

 The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability.
When handling the products, the following measures against electrostatic discharge are strongly
recommended:
Eliminating the charge
Grounded wrist strap, ESD footwear, clothes, and floors
Grounded workstation equipment and tools
ESD table/shelf mat made of conductive materials
 Proper grounding is required for all devices, equipment, and machinery used in product assembly.
Surge protection should be considered when designing of commercial products.
 If tools or equipment contain insulating materials such as glass or plastic,
the following measures against electrostatic discharge are strongly recommended:
Dissipating static charge with conductive materials
Preventing charge generation with moisture
Neutralizing the charge with ionizers

7. Directions for use

 The LEDs should be operated with forward bias. The driving circuit must be designed so that the LEDs are not subjected
to forward or reverse voltage while it is off. If reverse voltage is continuously applied to the LEDs, it may cause migration
resulting in LED damage.

8. Other
 Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above
specification.

7 Copyright
Revision :2 © 2010, Everlight All Rights Reserved. Release Date : Dec.08 . 2014. IssueRelease Date:2014-12-10
No: DAE-0000150_Rev.2 09:55:17.0
www.everlight.com
LifecyclePhase: Expired Period: Forever
 DATASHEET
LAMP
A1394B/3SYG/S530-E2

 When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these
specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does
not comply
with the absolute maximum ratings and the instructions included in these specification sheets.
 These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t
reproduce or cause anyone to reproduce them without EVERLIGHT’s consent.

8 Copyright
Revision :2 © 2010, Everlight All Rights Reserved. Release Date : Dec.08 . 2014. IssueRelease Date:2014-12-10
No: DAE-0000150_Rev.2 09:55:17.0
www.everlight.com
LifecyclePhase: Expired Period: Forever