Lab - View the Switch MAC Address Table

Topology

Addressing Table
Device Interface IP Address Subnet Mask

S1 VLAN 1 192.168.1.11 255.255.255.0

S2 VLAN 1 192.168.1.12 255.255.255.0
PC-A NIC 192.168.1.1 255.255.255.0
PC-B NIC 192.168.1.2 255.255.255.0

Objectives
Part 1: Build and Configure the Network
Part 2: Examine the Switch MAC Address Table

Background / Scenario
The purpose of a Layer 2 LAN switch is to deliver Ethernet frames to host devices on the local network. The
switch records host MAC addresses that are visible on the network, and maps those MAC addresses to its
own Ethernet switch ports. This process is called building the MAC address table. When a switch receives a
frame from a PC, it examines the frame’s source and destination MAC addresses. The source MAC address
is recorded and mapped to the switch port from which it arrived. Then the destination MAC address is looked
up in the MAC address table. If the destination MAC address is a known address, then the frame is forwarded
out of the corresponding switch port associated with that MAC address. If the MAC address is unknown, then
the frame is broadcasted out of all switch ports, except the one from which it came. It is important to observe
and understand the function of a switch and how it delivers data on the network. The way a switch operates
has implications for network administrators whose job it is to ensure secure and consistent network
communication.
Switches are used to interconnect and deliver information to computers on local area networks. Switches
deliver Ethernet frames to host devices identified by network interface card MAC addresses.

 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 8 www.netacad.com
Lab - View the Switch MAC Address Table

In Part 1, you will build a multi-switch topology with a trunk linking the two switches. In Part 2, you will ping
various devices and observe how the two switches build their MAC address tables.
Note: The switches used are Cisco Catalyst 2960s with Cisco IOS Release 15.2(2) (lanbasek9 image). Other
switches and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the
commands available and output produced might vary from what is shown in the labs.
Note: Make sure that the switches have been erased and have no startup configurations. If you are unsure
contact your instructor.

Required Resources
 2 Switches (Cisco 2960 with Cisco IOS Release 15.2(2) lanbasek9 image or comparable)
 2 PCs (Windows with terminal emulation program, such as Tera Term)
 Console cables to configure the Cisco IOS devices via the console ports
 Ethernet cables as shown in the topology
Note: The Fast Ethernet interfaces on Cisco 2960 switches are autosensing and an Ethernet straight-through
cable may be used between switches S1 and S2. If using another model Cisco switch, it may be necessary to
use an Ethernet crossover cable.

Instructions

Part 1: Build and Configure the Network

Step 1: Cable the network according to the topology.

Step 2: Configure PC hosts.

Step 3: Initialize and reload switches as necessary.

Step 4: Configure basic settings for each switch.

Open configuration window

a. Configure device name as shown in the topology.

b. Configure IP address as listed in Addressing Table.
c. Assign cisco as the console and vty passwords.
d. Assign class as the privileged EXEC password.
Aquí se muestran la configuración del S2 que fue igual al del S1 y el diagrama de conexión en Cisco Packet
Tracer.

 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 8 www.netacad.com
Lab - View the Switch MAC Address Table

Close configuration window

Part 2: Examine the Switch MAC Address Table

A switch learns MAC addresses and builds the MAC address table, as network devices initiate
communication on the network.

Step 1: Record network device MAC addresses.

a. Open a command prompt on PC-A and PC-B and type ipconfig /all.
Open Windows command prompt
Question:

What are the Ethernet adapter physical addresses?

PC-A MAC Address:
La dirección MAC es 00-E0-F7-6B-33-74

 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 8 www.netacad.com
Lab - View the Switch MAC Address Table

Type your answers here.

PC-B MAC Address:
La dirección MAC es 00-E0-8F-C6-E5-31

Type your answers here.

Close Windows command prompt

b. Console into switch S1 and S2 and type the show interface F0/1 command on each switch.
Open a configuration window
Questions:

On the second line of command output, what is the hardware addresses (or burned-in address [bia])?
S1 Fast Ethernet 0/1 MAC Address:
LA dirección MAC es 00-D0-FF-19-66-01

 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of 8 www.netacad.com
Lab - View the Switch MAC Address Table

Type your answers here.

S2 Fast Ethernet 0/1 MAC Address:
La dirección MAC es 00-E0-F9-20-D7-01

Type your answers here.

Close a configuration window

Step 2: Display the switch MAC address table.

Console into switch S2 and view the MAC address table, both before and after running network
communication tests with ping.

 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 5 of 8 www.netacad.com
Lab - View the Switch MAC Address Table

a. Establish a console connection to S2 and enter privileged EXEC mode.

Open a configuration window

b. In privileged EXEC mode, type the show mac address-table command and press Enter.
S2# show mac address-table
Even though there has been no network communication initiated across the network (i.e., no use of ping),
it is possible that the switch has learned MAC addresses from its connection to the PC and the other
switch.
Questions:

Are there any MAC addresses recorded in the MAC address table?
Si, se muestra a continuación.

What MAC addresses are recorded in the table? To which switch ports are they mapped and to which
devices do they belong? Ignore MAC addresses that are mapped to the CPU.
Se guarda una dirección MAC en la tabla, que es la dirección MAC de S1, esta se toma del puerto Fa0/1.
Sin embargo, no se guardan las direcciones MAC de los dispositivos de red es decir los PCs.
If you had not previously recorded MAC addresses of network devices in Step 1, how could you tell which
devices the MAC addresses belong to, using only the output from the show mac address-table
command? Does it work in all scenarios?
Si, se pueden determinar los dispositivos que están conectados entre ellos por su dirección MAC ya que
se muestra la dirección de ese dispositivo, solo se mostrarían las direcciones entre switches y el método
se puede usar para todos los escenarios excepto cuando múltiples direcciones MAC están asociadas al
mismo puerto.

Step 3: Clear the S2 MAC address table and display the MAC address table again.
a. In privileged EXEC mode, type the clear mac address-table dynamic command and press Enter.
S2# clear mac address-table dynamic
b. Quickly type the show mac address-table command again.
Questions:

Does the MAC address table have any addresses in it for VLAN 1? Are there other MAC addresses
listed?
No, solo se enlista la dirección MAC de S1.
Wait 10 seconds, type the show mac address-table command, and press Enter. Are there new
addresses in the MAC address table?
No, sigue igual.

Step 4: From PC-B, ping the devices on the network and observe the switch MAC address table.
a. From PC-B, open a command prompt and type arp -a.
Open a command prompt
Question:

Not including multicast or broadcast addresses, how many device IP-to-MAC address pairs have been
learned by ARP?

 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 6 of 8 www.netacad.com
Lab - View the Switch MAC Address Table

No ha aprendido ninguna dirección por ARP

b. From the PC-B command prompt, ping PC-A, S1, and S2.
Question:

Did all devices have successful replies? If not, check your cabling and IP configurations.
Si, todos los dispositivos tuvieron respuestas satisfactorias.
Ping S1

Ping S2

Ping PC-A

c. From a console connection to S2, enter the show mac address-table command.
Open a configuration window
Question:

Has the switch added additional MAC addresses to the MAC address table? If so, which addresses and
devices?
Si, aparecen direcciones MAC adicionales, están corresponden la primera a la dirección MAC de la
conexión VLAN 1 del S1, la segunda es la dirección del puerto Fast Ethernet 0/1 del S1, la tercera es la

 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 7 of 8 www.netacad.com
Lab - View the Switch MAC Address Table

dirección MAC del PC-B tomada en el puerto Fast Ethernet 0/18, y el ultimo es la dirección MAC del PC-
A tomada en el puerto Fast Ethernet 0/1.

From PC-B, open a command prompt and retype arp -a.

Question:

Does the PC-B ARP cache have additional entries for all network devices that were sent pings?
Si, guarda las direcciones físicas de los dispositivos a los que se les hizo el ping.

Type your answers here.

Close a command prompt

Reflection Question
On Ethernet networks, data is delivered to devices by their MAC addresses. For this to happen, switches and
PCs dynamically build ARP caches and MAC address tables. With only a few computers on the network this
process seems fairly easy. What might be some of the challenges on larger networks?
En una red más grande identificar todos los dispositivos de acuerdo a sus direcciones MAC es mas complejo
debido a que es necesario tener o realizar un mapa de red para identificar el numero de dispositivos para
realizar todo este proceso, además este tomara mas tiempo mientras mas dispositivos hallan.

 2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 8 of 8 www.netacad.com