800H - N4-4X - Parts RP
800H - N4-4X - Parts RP
800H - N4-4X - Parts RP
(Pictures are for illustration only. The exact size and dimensions will vary depending upon the catalog number)
Shallow Block PenTUFF (Low Voltage) Logic Reed Block Sealed Switch Block Stackable Sealed Switch Block
Contact Block
PenTUFF Logic Reed Sealed Switch Stackable Sealed
Shallow Block ➊➋
Number of Contacts (Low Voltage) Block ➊➋ Block ➌ Block ➌ Switch Block ➌
Cat. No. Cat. No. Cat. No. Cat. No. Cat. No.
1 N.O. 800T-XD1 800T-XD1V 800T-XD1R 800T-XD1P 800T-XD1Y
1 N.C. 800T-XD2 800T-XD2V 800T-XD2R 800T-XD2P 800T-XD2Y
1 N.O. (Early Make) 800T-XD3 800T-XD3V — — —
1 N.C. (Late Break) 800T-XD4 800T-XD4V — — —
1 N.O. - 1 N.C. 800T-XA 800T-XAV 800T-XAR 800T-XAP 800T-XAY
2 N.O. 800T-XA2 ➍ — 800T-XA2R ➍ — 800T-XA2Y
2 N.C. 800T-XA4 — 800T-XA4R — 800T-XA4Y
1 N.C. (Late Break) 1 N.O. 800T-XA1 — — — —
1 N.C. (Late Break) 1 N.C. 800T-XA7 — — — —
➊ Contact blocks with normally closed contacts meet direct drive positive opening standard requirements when properly fused to IEC 269-1 and
269-2. Shallow/mini contacts: 10 A gl or N type cartridge fuse. PenTUFF contacts: 6 A gl or N type cartridge fuse.
➋ Specify Bulletin 800TC for finger-safe contact blocks. Example: 800TC-XA.
➌ 800T operator using sealed switch and logic reed contact blocks and installed in a suitable enclosure are UL Listed as suitable for use in Class I,
Division 2/Zone 2 hazardous locations.
➍ Additional contacts cannot be stacked on XA2 and XA2R contact blocks.
➎ For contact ratings, see page 10-5.
➑ ➏
Shallow Contact Block Hardware
Description Cat. No.
➏ Contact Block Mounting Screw 800T-N335
➐ Screw Retainer 800T-N336
➑ Actuator Extender 800T-N337
10-85
Knowledgebase technotes can be found at http://support.rockwellautomation.com/
Page 4 of 9
Bulletin 800H Knowledgebase Technote ID # Q21228
30.5 mm Push Buttons 9/9/2003
Type 4/4X/13, Corrosion-Resistant/Watertight/Oiltight
Modifications and Accessories, Continued
Power Modules
Packaged in kit form for field installation. Lamps are listed on page 10-47.
Full Voltage Power Module Transformer Power Module Dual Input Power Modules
Cat. No. 800T-N330 Cat. No. 800T-N326 Cat. No. 800T-N296 (Transformer)
800T-N290 (Diode)
➊ Transformer type dual input provides circuit isolation via a miniature type relay. This module is used in conjunction with a 120V transformer.
➋ Diode type dual input provides circuit isolation via opposing diodes. Not recommended for use with solid-state outputs and neon indicators.
➌ 240V full voltage module contains 50% dropping resistors for use with a 120V incandescent lamp
0
Knowledgebase
10-86 technotes can be found at http://support.rockwellautomation.com/
Page 5 of 9
Knowledgebase Technote ID # Q21228 Bulletin 800H
9/9/2003 30.5 mm Push Buttons
Type 4/4X/13, Corrosion-Resistant/Watertight/Oiltight
Modifications and Accessories, Continued
Replacement Color Caps
Color caps listed below are for field replacement on installed devices or for completion of devices ordered with color caps omitted.
➊ Available in bulk quantities of 20. Add suffix (-BP) to the cat. no. and order in multiples of 20.
Non-Illuminated Plastic Mushroom Non-Illuminated Plastic Jumbo Mushroom Illuminated Mushroom Illuminated Jumbo Mushroom
Push Button Color Caps, Non-Illuminated Push Button Color Caps, Illuminated
1
Plastic Mushroom Plastic Jumbo Mushroom Mushroom Jumbo Mushroom
Color Color
Cat. No. Cat. No. Cat. No. Cat. No.
Red 800H-N114A 800H-N115A Red 800T-N304R 800T-N305R
Green 800H-N114B 800H-N115B Green 800T-N304G 800T-N305G
Blue 800H-N114C 800H-N115C Amber 800T-N304A 800T-N305A
Yellow 800H-N114E 800H-N115E Blue 800T-N304B 800T-N305B
Orange 800H-N114F 800H-N115F White 800T-N304W 800T-N305W
Gray 800H-N114G 800H-N115G Clear 800T-N304C 800T-N305C
Black 800H-N114H 800H-N115H — — —
White 800H-N114L 800H-N115L — — —
10-87
Knowledgebase technotes can be found at http://support.rockwellautomation.com/
Page 6 of 9
Bulletin 800H Knowledgebase Technote ID # Q21228
30.5 mm Push Buttons 9/9/2003
Type 4/4X/13, Corrosion-Resistant/Watertight/Oiltight
Modifications and Accessories, Continued
Replacement Color Caps, Continued
Color caps listed below are for field replacement on installed devices or for completion of devices ordered with color caps omitted.
Knob Type
0
Color Standard Knob Knob Lever
Cat. No. Cat. No.
Amber 800H-N154A 800H-N155A
Blue 800H-N154B 800H-N155B
Clear 800H-N154C 800H-N155C
Green 800H-N154G 800H-N155G
Red 800H-N154R 800H-N155R
White 800H-N154W 800H-N155W
Material
Insert Ethylene ●
Hypalon Silicone ● Urethane ●●
Material Propylene ●●
Cat. No. Cat. No. Cat. No. Cat. No.
Brass 800H-NR5 ➊ 800H-NR101 ➊ 800H-NR100 ➊ 800H-NR103 ➊
Stainless Steel 800HS-NR5 800HS-NR101 800HS-NR100 800HS-NR103
10-88
Knowledgebase technotes can be found at http://support.rockwellautomation.com/
Page 7 of 9
Knowledgebase Technote ID # Q21228 Bulletin 800H
9/9/2003 30.5 mm Push Buttons
Type 4/4X/13, Corrosion-Resistant/Watertight/Oiltight
Modifications and Accessories, Continued
Protective Boots
Boots supplied with control stations and components are made of a hypalon material with brass insert ring. To order boots with
silicone, urethane or ethylene-propylene material, see table below.
Material
Ethylene ●
Insert Silicone ● Urethane ●●
Color Hypalon Propylene ●●
Material ➊ ➊
➊
Cat. No. Cat. No. Cat. No. Cat. No.
Red 800H-N5A 800H-N101R 800H-N100R 800H-N103R
Green 800H-N5B 800H-N101G 800H-N100G 800H-N103G 1
Brass Black 800H-N5H 800H-N101B 800H-N100B 800H-N103B
Yellow 800H-N5E 800H-N101Y 800H-N100Y —
Blue 800H-N5C 800H-N101BL 800H-N100BL —
Red 800HS-N5A 800HS-N101R 800HS-N100R 800HS-N103R
Green 800HS-N5B 800HS-N101G 800HS-N100G 800HS-N103G
Stainless Steel Black 800HS-N5H 800HS-N101B 800HS-N100B 800HS-N103B
Yellow 800HS-N5E 800HS-N101Y 800HS-N100Y —
Blue 800HS-N5C 800HS-N101BL 800HS-N100BL —
10-89
Knowledgebase technotes can be found at http://support.rockwellautomation.com/
Page 8 of 9
Bulletin 800H Knowledgebase Technote ID # Q21228
30.5 mm Push Buttons 9/9/2003
Type 4/4X/13, Corrosion-Resistant/Watertight/Oiltight
Modifications and Accessories, Continued
Miscellaneous
Description Color Cat. No.
Gray 800T-N1
Closing Button
Where an enclosure or flush plate with more than the
required number of openings is used, this neat
appearing button can be supplied to close the unused
openings.
Black 800T-N1B
Closing Button
Cat. No. 800T-N1
Description Cat. No.
Replacement Knobs and Mounting Rings Selector switch knob and mounting ring Type 4 800H-N145F
Green 800T-N125
Color Insert Kits
Available on selector switches with removable color Blue 800T-N126
inserts. Standard knob and knob levers use the same
insert. If color All is selected, a packet of color inserts Yellow 800T-N127
will be furnished which includes one of each color
except orange. Color insert kits can also be ordered White 800T-N128
with operators at no additional charge.
Color Insert Kits Orange 800T-N286
Cat. No. 800T-N123
All 800T-N123
10-90
Knowledgebase technotes can be found at http://support.rockwellautomation.com/
Page 9 of 9 Knowledgebase Technote ID # Q21228 9/9/2003
Important User Information Because of the variety of uses for the products described in this publication, those responsible for
the application and use of this control equipment must satisfy themselves that all necessary steps
have been taken to assure that each application and use meets all performance and safety
requirements, including any applicable laws, regulations, codes and standards.
The illustrations, charts, sample programs and layout examples shown in this guide are intended
solely for purposes of example. Since there are many variables and requirements associated with any
particular installation, Rockwell Automation does not assume responsibility or liability (to include
intellectual property liability) for actual use based upon the examples shown in this publication.
Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application, Installation and Maintenance of
Solid-State Control (available from your local Allen-Bradley office), describes some important
differences between solid-state equipment and electromechanical devices that should be taken into
consideration when applying products such as those described in this publication.
Reproduction of the contents of this copyrighted publication, in whole or part, without written
permission of Rockwell Automation, is prohibited.
Throughout this document we use notes to make you aware of safety considerations:
!
Identifies information that is critical for successful application and
IMPORTANT
understanding of the product.
Use only replacement parts and devices recommended by Rockwell Automation to maintain the
integrity of the equipment. It is the user’s responsibility to ensure that the renewal part number
selected is properly matched to the model, series and revision level of the equipment being serviced.
Refer to National Fire Protection Association Standard No. NFPA70E, Part 2 and (as
applicable) OSHA rules for Control of Hazardous Energy Sources (Lockout/Tagout) and
OSHA Electrical Safety Related Work Practices for safety related work practices, including
procedural requirements for lockout/tagout, and appropriate work practices, personnel
qualifications and training requirements where it is not feasible to de-energize and lockout or tagout
electric circuits and equipment before working on or near exposed circuit parts.