Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Ams 5604

Download as pdf
Download as pdf
You are on page 1of 8
A AEROSPACE iwrennarionats | MATERIAL SPECIFICATION Steel, Corrosion Resistant, Sheet, Strip, and Plate 16.5Cr- 4.0Ni- 4.0Cu - 0.30Cb Solution Heat Treated, Precipitation Hardenable (Composition similar to UNS $17400) RATIONALE. ‘AMS5604J results from a limited scope ballot to revise the incorporation date for compliance with AS6279 (3.7), and incorporates general agreements related to Reports (4.4.2) and Identification (5.1.1). 4. SCOPE 14 Form “This specification covers a corrosion-resistant stee! in the form of sheet, strip, and plate 4.0 inches (102 mm) and under in nominal thicknass (soe 8 6). 1.2. Application “These products have been used typically for parts requiring corrosion resistance and high strength up to 600 °F (316 °C) ‘and where such parts may require welding during fabrication, but usage is not limited to such applications. 1.2.1 Certain processing procedures and service conditions may cause these products to become subject to stress- corrosion cracking; ARP1110 recommends practices to minimize such conditions. 2. APPLICABLE DOCUMENTS ‘The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the ‘extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is. specified. When the referenced document has been cancelled and no superseding document has been specified, the last Published issue of that document shall apply. 2.1. SAE Publications ‘Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA ‘and Canada) or +1 724-776-4970 (outside USA), wiww.s2e 019, ‘AMS2242 Tolerances Corrosion and Heat Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Sheet, Strip, and Plate {AE Tecacal Saraiva Fans pose at “Toop pub by SAE advance a ta tice an nga acon The ws ofp aly ‘okay, on ppb en ub fr ny free, ang any ten igen ring Heron Be te espns he we” ‘SAE rus cach etnicl repeat es ery ve Jers hh te tay bere firmed, subod casted, SAE Ines your wan cormets ard Soesio Copy © 2018 SAE ematonal ‘Aap eto No rot paca maybe meses a nena eye ranean nym yy mae Ac Mecha SPORES ‘cra. oherase, went or won permason oF SAE TOPLACEA DOCUMENT ORDEKE Tet 7.406738 nade UtAand Cantey [BAE values your Input To provide feedback on Stratreair use an) ‘Technical Report, please visit Se cas tpitstandards 238 oc/AMSSE0) SAE WEB ADORESS: Ineo ewe eae oo SAE INTERNATIONAL AMSS604™j Page 20f 8 AMS2248 AMS2315, AMS2371 ‘AMS2750 AMS2807 ARPI110 ARPI917 AS41094 AS6279 ‘Chemical Check Analysis Limits Corrosion and Heat-Resistant Steels and Alloys, Maraging and Other Highly Alloyed Steels, and Iron Aloys Determination of Delta Ferrite Content Quality Assurance Sampling and Testing Corrosion and Heat Resistant Steels and Alloys Wrought Products and Forging Stock Pyrometry Identification Carbon and Low-Alloy Steels, Corrosion and Heat-Resistant Steels and Alloys Sheet, Stip, Plate, and Aircraft Tubing Minimizing Stress Corrosion Cracking in Wrought Forms of Steels and Corrosion Resistant Steels and Alloys CClantication of Terms Used in Aerospace Metals Specifications ‘Sheet and Strip Surface Finish Nomenclature ‘Standard Practice for Production, Distribution, and Procurement of Metal Stock 22 ASTM Publications ‘Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610- 832.9585, www asim org. ASTM A370 Mechanical Testing of Stee! Products ASTM A480/A480M —Flat-Rolled Stainless and Heat-Resisting Stee! Plate, Sheet, and Strip ASTM E140 ‘ASTM E290 ASTM £353, Hardiness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, Scleroscope Hardness, and Leeb Hardness: Bend Testing of Material for Ductilty Chemical Analysis of Stainless, Heal-Resisting, Maraging, and Other Similar Chromium-Nickel- Iron Alloys: SAE INTERNATIONAL AMS5604™J Page 30f 8 3. TECHNICAL REQUIREMENTS 3.1. Composition Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM £353, by spectrochemical methods, or by other analytical methods acceptable to purchaser. Table 1 - Composition Element Min Max. Carbon = 007 Manganese - 1.00 ‘Silicon - 1.00 Phosphorus = 0040 ‘Sulfur = 0.030 Chromium 1500 17.50 Nickel 3.00 5.00 ‘Columbium SC 0.45 Copper 3.00 5.00 ‘Molybdenum 0.50 3.4.1. Check Analysis Composition variations shall meet the applicable requirements of AMS2248, 32. Condition The product shall be supplied inthe folowing condition: 3.2.1 Sheetand Strip Cold rolled, solution heat treated, and, unless solution heat ireatmentis performed in an almasphere yielding a bight finish, descaled having @ surface appearance comparable to the commercial corrosion-resistant finishes described in ‘ASTM A48Q/A480M and AS4194 and 3.2.1.1 oF 3.2.1.2, as applicable. 321.4 Sheet No. 20 finish 321.2. Stip No. 1 stip irish, 322 Plate Hotrolled, solution heat treated, and descaled 33 Solution Heat Treatment Excopt as specified in 3.3.1, the product shall be solution heat treated by heating to 1900 *F + 25 “F (1038 °C + 14 °C), holding at heat for atime commensurate with the thickness and the heating equipment and procedure used, and cooling to below 90 °F (32 °C). Pyrometry shall conform to AMS2750. 5 RETR MATIONAL Pie act 8 83.1 Continuous Hoat Troating af feat and Sirip Proce parameter (2g. fimann lemporatrs ect pons, hoot ws tol ra, cl) for conficun host rang tie sha be at aed by tesing of product to requrements of 4. Pak al ol hs sind Fa was en ax.book118.com “The product shall-conform:to-the following requirements; tensile, hardness, and bend testing shall be posfomad in ereedance with ASTM ATO: 344 As Solution Heat Treated 3414 Tonsile Properties ‘Shall bes as shown in Table 2 for nominal thickness 0.015 to 0.1874 inch (0.38 to 4.760 mm), inclusive. 3412 Hariness ‘Shall bo not higher than 38 HRC, or equivalent (see 8.2). 244.2 Microstructure “The prtuct shall contain not more than 5% ferrite, determined in accordance with AMS2315. 441.4 Sending Prov 0.408 inch (2.77 be tested in accordance with ASTM E290 using a ssmpke prepared nominally 0.75 i ing parallel to the direction of ring and shes witha, without cracking, bending da diameter equal to 18 times the nomi thickness of tha poset ease of epee fhe rei of ts using the gaa bond tos of ASTM E200 shal govern 942 After Precipitation Heat Treatment FEIN) “The eetiton heat treated product 40 inches (102 mm) and under in nominal thickness shallhave tensile propatica spciind 4.2.1 and hardness specified in 34.2.2 after being precipitation heat treated toa particular condition in aronnane with tha carreapding temperature and times shown in Table 3 and cooled as required. Tensile and hardness tests “vil ha trade in oniy tne H800 condtion unless purchaser specifies another heat reated condition. Table 3 - Precipitation hardening conditions eon ——Teriprara Tas —— 800 sees er Gon cs aes sees er Gon cs vias s025"F 2 10°F sec tors tore-e 2 10°F roc vito oo-rs 10-F 03-c 26-9) petccoe com H1150___1150°F + 10°F (621 "C46 SAE INTERNATIONAL AMS5604™J Page 5 of 8 3.4.2.1 Tensile Properties Shall be as shown in Table 4. Table 4 Table 4A - Minimum tensile properties after precipitation heat treatment, inch/pound units Elongation Nominal Tensile Yield Strength at inZInches Reduction Thickness Strength 0.2% Offset or4D of Area ‘Condition Inches ksi si % % 900 Up 100.1874, incl 190, 170 5 - 0.1875 100.625, "incl 130 170 8 30 Over 01625 to.4.000, incl 190 170 10 35 H925 Up ___ 100.1674, inct 170 185 5 = 0.1875 10 0.625, "incl 170 155 8 30 Over 01625 t0.4.000, incl 170 155 10 35 H1025 Up __ 100.1674, inct 155 148, 5 ~ 0.1875 10 0.625, "incl 155 145, 8 35 Over 0.625 t0.4.000, incl 155 145 2 40 H1075 Up __ 100.1874, incl 145, 125 5 - 0.1875 100.825, "incl 145, 125 9 35 Over 0.625 to.4.000, incl 145, 125 8 45 1100 Up __ 100.1674, incl 140 115 5 = 0.1875 10 0.625, "incl 140 115 10 35 Over 0.625 t0.4.000, incl 140 115 14 45 H1150 Up __ 100.1874, inct 135 105 8 ss 0.1875 10 0.625, "inci 195 105 10 Over 01625 _t0.4.000, incl 135, 105 16 SAE INTERNATIONAL ___AMss604™j Page 6 of 8 Table 48 - Minimum tensile properties after precipitation heat treatment, SI units Elongation Nominal Tensile Yield Strength in 50.8mm Reduction ‘Thickness Strength at 0.2% Offset. or 4D of Area Condition Milimeters MPa. MPa % % F900 Up 0 4.760, incl 1310 1172 5 = 4.761 0 1588, incl 1310 1172 8 30 Over 15.88 to 101.60, incl 1310 1172 10 35 925 Up_ to 4.760, ind 1172 1069 5 = 4.761 0 1588, incl 4172 1069 a 30 Over 15.88 to 101.60, incl 1172 1069 10 35 1025 Upto 4.760, incl 1069 1000 5 a 4.761 to 1588, incl 1069 1000 a 35 ‘Over 15.88 0 101.60, incl 1069 1000 12 40 1075, Up_ 1 4.760, incl 1000 862 5 - 4.761 to 1588," incl +1000 862 9 35 Over 15.88 to 101.60, incl +1000 862 13 45 41100 Up_ to 4760, incl 965 793 5 a 4,761 t0 15.88, incl 965 793 10 35 Over 15.88 to 101.60, ind 965 793 4 45 41150 Up_ 10 4760, incl 931 728 8 = 4.761 t0 15.88," incl 931 28 10 40 Over 15.8810 101.60._ incl 931 724 16 50 34.22 Hardness ‘Shall be within the range shown in Table § for the corresponding precipitation heat treatment condition. Table 5- Hardness Condition HB RG BY, F900 37510444 401047 411 10 510 925 36210415 381045 39210473 1025 33110388 351042 36410431 1075 31110363 331030 344 to401 1100 30210352 321038 33310392 1150 26910 341281037 280 t0 383 3.5 Mechanical property requirements for product outside the range covered by 1.1 shall be agreed upon between purchaser and producer. 36 Quality “The product, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the product 37 Tolerances Shall conform to all applicable requirements of AMS2242; flatness tolerance for sheet shall be as specified for cold-worked austenitic sheet in half-hard temper. ‘SAE INTERNATIONAL ___amss6o¢j «Page 7 of 8 3.8 Production, distribution, and procurement of metal stock shall comply with AS6279. After production and certification to the specified requirements, plate within the size range of 1.1 may be cut in a plane perpendicular to the short transverse dimension by the distributor to supply plate ofa thinner gage. The requirement for compliance with AS6279 becomes effective 04/01/2019. 4. QUALITY ASSURANCE PROVISIONS 4.1. Responsibility for Inspection ‘The producer of the product shall supply all samples for producer's tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements. 42 Classification of Tests: 42.1 Acceptance Tests ‘Composition (3.1), tensile properties (3.4.1.1), hardness (3.4.1.2), bending (3.4.1.4) as solution heat treated, and tensile properties (3.4.2.1) and hardness (3.4.2.2) after precipitation heat treatment to the hardened condition (H900, or as specified by purchaser), and tolerances (3.6) are acceptance tests and shall be performed on each heat or lot as applicable. 422 Periodic Tests ‘Microstructure (3.4.1.3) and properties in other than the specified precipitation hardened condition (see 3.4.2) are periodic tests and shall be performed as a frequency selected by the producer unless frequency of testing is specified by the purchaser. 43° Sampling and Testing ‘Shall be in accordance with AMS2371. 44° Reports “The producer of the product shall fumish with each shipment a report showing the producer's name and country where the metal was metted (e.g. final met in the case of metal processed by multiple melting operations) and the results of tests for ‘chemical composition of each heat and for tensile properties, hardness and bending as solution heat treated, and tensile properties and hardness after precipitation heat treatment of each lot, and stating that the product conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5604J, product form, size, and quantity. 4.4.1 When the product size is outside the range covered by 1.1, the report shall contain a statement to that effect. 442 When material produced to this specification is beyond the sizes allowed in the scope or tables, or other exceptions: are taken to the technical requirements listed in Section 3 (see 5.2.1.1), the report shall contain a statement “This material is certified as AMS5604,(EXC) because ofthe following exceptions.” and the specific exceptions shall be listed. 45° Resampling and Retesting ‘Shall be in accordance with AMS2371, 5. PREPARATION FOR DELIVERY 5A Identification ‘Shall be in accordance with AMS2807. ‘SAE INTERNATIONAL AMS5604™) Page 808 5.1.1. When technical exceptions are taken (se 4.4.2), the material shall be marked with AMSS604J(EXC). 52. Packaging ‘The product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules ‘and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and Safe dalvory 6. ACKNOWLEDGMENT ‘A producer shall mention this specification number and ts revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 Revision indicator ‘A change bar (|) cated in the left margin is for the convenience of the user in locating areas where technical revisions, not ‘editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document ttle indicates a compiete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 82 Hardness conversion tables for metals are presented in ASTM E140 83 Terms used in AMS are clarified in ARP1917 84 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary: dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents ofthe primary units and are presented only for information 85 Unless otherwise specified, the material producer shall work to the revision ofthis specification (AMS5604) in effect, ‘on the date of order placement. Unless otherwise specified, material manufactured and certified to the immediately previous revision of this specification (AMS5604) may be procured and used untl inventory is depleted. 86 Purchase documents should specify not less than the following: AMS5604J ‘Size of product desired Quantity of product desired Property and acceptance requirements from the cognizant engineering organization applicable to sizes outside the range listed in 1.1 Precipitation heat-treated condition for testing if other than H900 (see 3.4.2) PREPARED BY AMS COMMITTEE "F*

You might also like