GRAVURE TROUBLE-SHOOTING GUIDE

DEFECT PROCESS PROBLEM PROBABLE CAUSE TEST POSSIBLE REMEDIES

Blade angle too sharp Flatten blade angle
Incorrect blade setting
Too much blade pressure Reduce blade angle
CHATTER
Blade too sharp High pigment ink sharpening blade Solids test Replace ink if out of spec

Dried ink on fountain Clean off the fountain

Uneven ink flow from fountain
Fountain set up incorrectly Remount fountain

Fountain too far away from cylinder Adjust fountain closer to cylinder
Ink flow valve not open enough Open valve wider / check for blockage
INK
Too little ink flow from fountain Ink filter clogged Change ink filter
FLOW
Ink pump not operating correctly Pressure gauge Replace ink pump
Fountain baffles are plugged or bent Clean / adjust baffles
Fountain too close to cylinder Adjust fountain away from cylinder
Too much ink flow from fountain
Ink flow valve open too wide Close valve slightly
Low temperature in dryer heat gun Raise dryer temperature
Low air flow in dryer magnehelic Increase dryer air flow
Ink not drying completely on web
Low steam pressure to dryer Notify maintenance
Press speed too high (small dryers only) Decrease press speed

High ink viscosity Solvent evaporation from ink viscosity test Slowly add more solvent to ink

PICKING Too much pressure on Impression roller measure nip flat area Decrease roller pressure
Too little pressure on impression roller measure nip flat area Increase roller pressure
Incorrect pressure on impression roller Impression roller is the wrong durameter durometer Tester Change roller durometer
Dirty impression roller Clean the impression roller
Defective / uneven impression roller Change the impression roller

Chill rollers too warm Water supply not cold enough / not flowing heat gun Notify maintenance
 GRAVURE TROUBLE-SHOOTING GUIDE
DEFECT PROCESS PROBLEM PROBABLE CAUSE TEST POSSIBLE REMEDIES
Solvents blended incorrectly Have ink room adjust solvent blend
Incorrect solvent blend G.C. test (Add NPA for P-200 ink system)
High room temp causing evaporation Notify maintenance
Blade angle too sharp Flatten blade angle
Incorrect blade setting
Blade too thin Replace Blade

High ink viscosity Solvent evaporation from ink viscosity test Slowly add more solvent to ink

C Cylinder engraved incorrectly microscope De-chrome & Re-chrome cylinder

H Replace cylinder
Cell walls on cylinder too wide
A Cylinder worn De-chrome & Re-chrome cylinder

N Replace cylinder
Scum blower setting too high Lower air setting or turn off scum blower
N Too much air blowing on cylinder
Fan or draft blowing on cylinder puff tester Redirect air flow
E
Chill rollers too warm Water supply not cold enough / not flowing heat gun Notify maintenance
L
I Too much pressure on Impression roller measure nip flat area Decrease roller pressure
Incorrect pressure on impression roller Impression roller is the wrong durameter durometer Tester Change roller durometer
N
Defective / uneven impression roller Change impression roller
G High room temperature Notify maintenance
Install ink chillers
Ink temp too high
Impression nip point friction Decrease impression roller pressure
Too much agitation of the ink Check the ink pump
pressure gauge Change ink filter
Ink not thoroughly mixed Ink pump not operating correctly Unclog agitator elbow
Replace pump
 GRAVURE TROUBLE-SHOOTING GUIDE
DEFECT PROCESS PROBLEM PROBABLE CAUSE TEST POSSIBLE REMEDIES
Add new ink to old ink
Low ink Viscosity Too much solvent in ink viscosity test
Replace ink
Ink pump not operating correctly pressure gauge Change ink filter
Unclog agitator elbow
Ink is not thoroughly mixed
M Replace pump

O Ink not properly mixed at formulation Return to ink room for mixing

T The ink has been "SHOCKED" Solvent poured too quickly into ink Replace ink

T Blade angle too flat Sharpen blade angle

Incorrect blade setting
L Blade too low relative to nip point Raise blade closer to nip point

E Too little pressure on the impression roller measure nip flat area Increase pressure to the roller
Insufficient pressure at the nip point Impression roller is wrong durometer Change the roller to a harder durometer
Uneven wax coating weight on stock paper Change the paper

Incorrect cylinder engraving Engraving too deep / too shallow Replace the cylinder

Dried bits of ink in the ink Clean / change blade

Filter ink
Dirty blade Metal bits in the ink Filter ink with magnet

STREAKS Paper dust contaminating blade Check press vacuum system

Dirty rollers contaminating blade Clean rollers

Blade not oscillating Mechanical failure Notify Maintenance

 GRAVURE TROUBLE-SHOOTING GUIDE
DEFECT PROCESS PROBLEM PROBABLE CAUSE TEST POSSIBLE REMEDIES

I Too much ink flow from fountain Ink flow valve open too wide Close valve slightly
N
K Ink flowing over splash guard Blade angle too flat Adjust blade angle

.
S Ink splash guard leaking Splash guard set up incorrectly Reset splash guard inside ink pan

P Hose fitting not securely attached Tighten hose fitting

L Hose to fountain leaking Hose gasket worn, missing or broken Replace gasket
A Hose has a hole in it Replace hose
S Fountain baffle / ink splash deflector is Replace fountain baffle
Baffle set up incorrectly
H missing Set up ink splash deflector
Not enough air blowing on cylinder Turn on scum blower
Ink film not drying on the non print area of
Increase scum blower air setting
the cylinder
Press speed too fast (small dryers only) Decrease press speed
Buff the cylinder
Cylinder surface is too rough Cylinder not polished enough RZ test
Replace the cylinder
S
High ink viscosity Solvent evaporation from ink viscosity test Slowly add more solvent to ink
C
U Worn blade
Running for long periods of time Replace the blade
Rough / high cylinder edges Have cylinder filed down
M Have ink room adjust solvent blend
Incorrect solvent blend in ink Solvents blended incorrectly G.C. test
(add IPA for P-200 ink system)
Blade angle too flat Sharpen blade angle
Incorrect blade setting Blade too close to nip point Lower blade away from nip point
Blade too thick Change blade
 GRAVURE TROUBLE-SHOOTING GUIDE
DEFECT PROCESS PROBLEM PROBABLE CAUSE TEST POSSIBLE REMEDIES

High ink viscosity Solvent evaporation from ink viscosity test Slowly add more solvent to ink

Add new ink to old ink

Low ink viscosity Too much solvent in ink viscosity test
C Replace ink

O Color mis-match at the ink room Wrong formulation used Replace ink

L Ink pump not operating properly pressure gauge Change filter

O Unclog agitator elbow
Ink not thoroughly mixed
R Replace pump
Ink not properly mixed at formulation Return to ink room for mixing
.
Blade angle too sharp or flat Adjust blade angle
O Incorrect blade setting Blade too high / too low relative to nip point Adjust blade hieght
F Blade too thick / too thin Replace blade

F Cylinder cells too deep / too shallow Cylinder is incorrectly engraved Replace cylinder

Wax coating weight on paper uneven Defective coating on stock paper Change paper

Dried bits of ink in ink Clean / change blade

Filter ink
Dirty blade Metal bits in ink Filter ink with magnet
Paper dust contaminating blade Check press vacuum system
DRAGS
Dirty rollers contaminating blade Clean rollers
Blade angle too sharp or flat Adjust blade angle
Incorrect blade setting Blade too low relative to nip point Raise blade closer to nip point
Blade too thick Replace blade

[ DRAGS CONTINUED NEXT PAGE ]

 GRAVURE TROUBLE-SHOOTING GUIDE
DEFECT PROCESS PROBLEM PROBABLE CAUSE TEST POSSIBLE REMEDIES

Chrome nodules on cylinder Cylinder buffed incorrectly Re-buff cylinder

Rough blade Blade polished incorrectly Replace blade

DRAGS
(CONTINUED)
Blade not oscillating Mechanical failure Notify maintenance

Worn blade Running for long periods of time Replace blade

Chrome nodules on cylinder Cylinder buffed incorrectly Re-buff cylinder

Cylinder not polished enough RZ test Re-buff cylinder

Contamination under the blade Re-buff / replace cylinder
Clean / change blade
Filter ink
Lines are scratched into the cylinder
L Finlter ink with magnet
Check press vacuum system
I
Clean rollers
N Fountain set too close to cylinder Adjust fountain setting away from cylinder
E Contamination in ink Change blade

S Nicked blade
Filter ink
Blade polished incorrectly Change blade
Rough / high cylinder edges Have cylinder edges filed down

Blade not oscillating Mechanical failure Notify maintenance

Lines are in the wax coating on the paper Defective coating on stock paper Change the paper
 GRAVURE TROUBLE-SHOOTING GUIDE
DEFECT PROCESS PROBLEM PROBABLE CAUSE TEST POSSIBLE REMEDIES
Incorrect artwork used
Cylinder design incorrect Replace cylinder

M Over-use De-chrome & Re-chrome cylinder

I Worn cylinder Cylinder buffed too much Replace cylinder

S Blade angle too sharp or flat Flatten blade angle

Blade angle too sharp Flatten blade angle
S Incorrect blade setting
Blade too low relative to nip point Raise blade closer to nip point
I Too little pressure on the impression roller measure nip flat area Increase pressure to the roller
N Impression roller is wrong durometer durometer tester Change roller to a harder durometer

G Insufficient pressure at the nip point Uneven pressure on impression roller Balance impression roller pressure
Defective or worn impression roller Replace impression roller
.
Cylinder mis-aligned in carriage Remount cylinder
P High ink viscosity viscosity test Slowly add more solvent to ink
R Clean / scrub out cylinder with solvent

I Too much air blowing on cylinder Turn off scum blowers or redirect fans

N Cylinder filled in with ink Clean / scrub out cylinder with solvent
Blade too far from nip point Move blade closer to nip point
T Ink pan too low Adjust ink pan
Ink temp too high thermometer Install ink chiller
 GRAVURE TROUBLE-SHOOTING GUIDE
DEFECT PROCESS PROBLEM PROBABLE CAUSE TEST POSSIBLE REMEDIES
Low temperature in dryer heat gun Raise dryer temperature
Low air flow in dryer magnehelic Increase dryer air flow

B Clean air nozzles

Ink not drying completely on web Adjust air nozzle angle
L Low steam pressure to dryer Notify maintenance
O Press speed too high (small dryers only) FPM tach Decrease press speed
C Incorrect solvent blend G.C. test Have ink room adjust solvent blend

K Rolls wound too tightly

Too much tension on web Decrease press tension
Coating on paper uneven Change the paper
I High temperature in dryer Lower dryer temperature
N High air flow in dryer Decrease dryer air flow
G Ink skinning over Press speed too high Decrease press speed
Incorrect solvent blend G.C. test Have ink room adjust solvent blend
Low temperature in dryer Increase dryer temp