Reference manual Operation

Operation

The control panel 10

The LC display 11

Online mode 12

Offline mode 13

Setup mode 14

Messages in the LC display 15

Key functions when turning on the printer 16

Changing the ribbon cassette (black ribbon) 17

Changing the ribbon cassette (multicolour version) 25

BACK PRINT
? QUIT
Reference manual Operation

Paper handling 33
Changing the paper type 33

Loading fanfold paper 35

Loading single sheets 38

Paper transport 41

Moving the paper to the tear position 42

Settings 44
Setting the tear position 44

Setting the first printing line (TOF) 46

Setting the print head gap 49

Selecting character density and font 51

BACK PRINT
? QUIT
Reference manual Operation

2T model 53
Introduction 53

Rear tractor paper path 54

Loading paper into the rear tractor 55

Selecting the rear tractor 58

BACK PRINT
? QUIT
Reference manual The control panel

The control panel

The control panel keys are used for controlling your work with the printer.
The control panel is located on the front left side of your printer and con-
sists of a two-line LC display and six keys.
The functions of the keys depend on the printer’s current mode (status).
There are four basic modes.
The Online mode is the printer’s normal operating mode. Data from your
computer can be received and printed.
In the Offline mode the link between printer and computer is interrupted, i.e.
no data can be received and printed.
In the Setup mode you can either select the printer menu or carry out the
so-called quick-switch function. The quick-switch option was included so
that you can change the most important parameters (adjustments, charac-
ter density, font, paper path, adjustments i.e. head gap) directly without
having to enter them via the menu. The character density and font par-
ameters can also be set permanently in the printer menu mode.
In the Menu mode further printer settings (line spacing, size of the interface
buffer etc.) can be altered and saved permanently.

BACK PRINT
? QUIT

10
Reference manual The control panel

➤ The LC display The LC display tells you all the important printer settings and informs you
which functions are currently assigned to which keys.

The upper line informs you that the printer is either in online or offline
mode (in the example below the printer is in the Online mode), and the
selected paperpath (below: Trac1 = tractor mode).

The second line informs you which functions are currently assigned to
which keys. The word or symbol directly above a key tells you the cur-
rent function of the key. In our example the right key is assigned with the
Tear function. If you were to press this key the loaded fanfold paper
would be advanced to the tear position.

Example:

Printer status Paper path

Online Trac1
Key functions Tear Online

1 2 3 4
Setup

BACK PRINT
? QUIT

11
Reference manual The control panel

➤ Online mode After switching on, the printer is automatically set to online mode. Only in
this mode can it receive data from the computer.

Tear key (4): Activates the tear function when fanfold paper is loaded
Online Tractor1 (see Moving the paper to the tear position).
Tear Online
If Load is displayed above this key, no paper is loaded in the printer;
1 2 3 4 press the key to feed paper to the printing position.
Setup Setup key: Sets the printer to setup mode.
Online key: Sets the printer to offline mode.

BACK PRINT
? QUIT

12
Reference manual The control panel

➤ Offline mode Only in this mode is it possible to perform step, line, or form feeds from the
control panel (see Paper transport); however, data cannot be received.

Park key (1): Clears the paper path with paper loaded and activates
Offline Tractor1 paper path quick selection (see Changing the paper type).
Park Load Online
Key (2): Short keypress: Microstep forward.
1 2 3 4 Long keypress: Continuous paper feed.
Setup Key (3): Short keypress: Microstep reverse.
Long keypress: Continuous paper reverse feed up to the park position.
Load key (4): If no paper is loaded, see above.
If paper is loaded: Short keypress:
Line Feed (LF); long keypress: Form Feed (FF).
Setup key: Sets the printer to setup mode.
Online key: Sets the printer to online mode.

BACK PRINT
? QUIT

13
Reference manual The control panel

➤ Setup mode In this mode, you can program various printer settings.

Setup key: Sets the printer to setup mode, in which the following
Adjust Paperway settings can be selected:
Menu Char Online
Menu key (1): Other menu settings.
1 2 3 4 Adjust key (2): Setting the tear position, first printing line and print
Setup head gap.
Paperway key (3): Paper path.
Char key (4): Font and number of characters per inch.

Access to the other menu settings (Menu) is disabled by the

manufacturer. For information on how to enable access, refer to
Enabling access to menu mode and about the available settings,
refer to Menu description table).

BACK PRINT
? QUIT

14
Reference manual The control panel

➤ Messages in the LC If the printer detects an internal fault or user error or if it expects you to
display do something, a message will appear in the LC display. Below you will
find a list of messages with brief descriptions of each message. The
messages are described in greater detail in the chapter Troubleshooting.

Meldung Bedeutung
Eject error The printer cannot eject the paper / advance it to park position.
Hardware Alarm Internal hardware error, contact your dealer or service technician.
Head hot The printer reports that the print head is hot and that print speed will be
reduced.
Initializing This message appears during the printer’s initializing phase.
Load error The printer cannot draw in the loaded paper.
Loading default Indicates that the printer is being initialised and is carrying out the internal self-
test immediately after turning on the printer. Factory defined parameters will
be reloaded in all available menues.
Out of paper The printer has detected paper end during operation / printer was switched on
with no paper loaded.
Parity error A parity error during data transmission is indicated.
Press any key The user is requested to press any key.
Tear Paper off The user is requested to tear off paper which has been advanced to the quick
tear edge.
Selftest After power-on, the printer executes a short hardware self-test.

BACK PRINT
? QUIT

15
Reference manual The control panel

➤ Key functions when If you keep one of the following keys pressed during power-on until the
turning on the printer printer has completed initialisation and the self-test display disappears,
three functions are activated:

If you keep the Online key depressed while turning on the printer, you enter
the printer’s Self-Test mode. The Self-Test mode is described in the section
Test functions of this manual.
If you keep the Setup key depressed while turning on the printer, you regain
access to the printer menu if you had locked it before with the help of the
MenLock function. The MenLock function is described in the Menu descrip-
tion table at the end of this chapter.
If the four function and select keys (keys 1 to 4) are depressed simulta-
neously while turning on the power, all printer settings are reset to the
default values (except the Form length setting in Test mode).

BACK PRINT
? QUIT

16
Reference manual Changing the ribbon cassette (black ribbon)

Changing the ribbon cassette (black ribbon)

STOP Before opening the cover, make sure that
the printer is switched on so that it can
execute automatic preparations for rib-
bon changing (widening the print head
gap).

Move the paper to the park position.

Open the printer top cover.

BACK PRINT
? QUIT

17
Reference manual Changing the ribbon cassette (black ribbon)

Cautiously slide the print head carriage to the left

stop (viewed from the printer front).

STOP The print head heats up during printing.

Let it cool down before touching, if ne-
cessary.

Move the coloured friction tab to the left (direction of

the arrow) as shown in the figure and raise the fric-
tion mechanism.

BACK PRINT
? QUIT

18
Reference manual Changing the ribbon cassette (black ribbon)

Remove the used cassette.

We recommend use of genuine ribbon

cassettes only.

BACK PRINT
? QUIT

19
Reference manual Changing the ribbon cassette (black ribbon)

Raise the coloured insertion tongue A.

Insert the coloured ribbon tension knob into the right-

hand front location of the new ribbon cassette. Turn
the knob in the direction of the arrow in order to take
up slack of the ribbon.

BACK PRINT
? QUIT

20
Reference manual Changing the ribbon cassette (black ribbon)

Slightly tilt the ribbon cassette forwards and thread

in the ribbon between the coloured insertion tongue
and the ribbon support (transparent plastic plate).

Align and insert the cassette into the guides on the

left and right, then press down until it clicks into
place.

BACK PRINT
? QUIT

21
Reference manual Changing the ribbon cassette (black ribbon)

Insert the coloured tension knob into one of the two

locations.

Turn the tension knob to take up slack in the ribbon

until it is seated correctly at the bottom in the ribbon
support.

Press down the coloured insertion tongue A.

BACK PRINT
? QUIT

22
Reference manual Changing the ribbon cassette (black ribbon)

Move the print head carriage back and forth several

times. If the ribbon is correctly seated, there must be
no perceptible resistance.

The ribbon should be transported during

the travel from left to right. If this is not
the case, you should check that the rib-
bon cassette is correctly inserted on the
right.

BACK PRINT
? QUIT

23
Reference manual Changing the ribbon cassette (black ribbon)

Press the friction mechanism down until it clicks into

place.

Close the top cover.

BACK PRINT
? QUIT

24
Reference manual Changing the ribbon cassette (multicolour version)

Changing the ribbon cassette (multicolour version)

STOP Before opening the cover, make sure that
the printer is switched on so that it can
execute automatic preparations for rib-
bon changing (widening the print head
gap and lifting the ribbon).

Move the paper to the park position.

Open the printer top cover.

BACK PRINT
? QUIT

25
Reference manual Changing the ribbon cassette (multicolour version)

Cautiously slide the print head carriage to the left

stop (viewed from the printer front).

STOP The print head heats up during printing.

Let it cool down before touching, if ne-
cessary.

Move the coloured friction tab to the left (direction of

the arrow) as shown in the figure and raise the
friction mechanism.

BACK PRINT
? QUIT

26
Reference manual Changing the ribbon cassette (multicolour version)

Remove the used cassette.

We recommend use of genuine ribbon

cassettes only.

BACK PRINT
? QUIT

27
Reference manual Changing the ribbon cassette (multicolour version)

Lift the coloured insertion guide A. Carefully pull the

.B
ribbon carrier B one step upwards.

Insert the coloured ribbon tension knob into the right-

hand front location of the new ribbon cassette. Turn
the knob in the direction of the arrow in order to take
up slack of the ribbon.

BACK PRINT
? QUIT

28
Reference manual Changing the ribbon cassette (multicolour version)

Slightly tilt the ribbon cassette forwards and thread

in the ribbon between the coloured insertion tongue
and the ribbon support (transparent plastic plate).

Align and insert the cassette into the guides on the

left and right, then press down until it clicks into
place.

BACK PRINT
? QUIT

29
Reference manual Changing the ribbon cassette (multicolour version)

Insert the coloured tension knob into one of the two

locations.

Turn the tension knob to take up slack in the ribbon

until it is seated correctly at the bottom in the ribbon
support.

Press the ribbon carrier B down and lower the

coloured insertion aid A.
A

BACK PRINT
? QUIT

30
Reference manual Changing the ribbon cassette (multicolour version)

Move the print head carriage back and forth several

times. If the ribbon is correctly seated, there must be
no perceptible resistance.

The ribbon should be transported during

the travel from left to right. If this is not
the case, you should check that the rib-
bon cassette is correctly inserted on the
right.

BACK PRINT
? QUIT

31
Reference manual Changing the ribbon cassette (multicolour version)

Press the friction mechanism down until it clicks into

place.

Close the top cover.

BACK PRINT
? QUIT

32
Reference manual Paper handling

Paper handling
This section describes how to set the paper type, load fanfold paper and
single sheets, transport paper and move the paper to the tear position.

➤ Changing the paper type You can change the paper type either from an application program, by
means of the paper path quick selection feature or in the Setup menu. In
this section, the quick selection feature is described; for detailed informa-
tion on how to make this setting via the Setup menu, refer to the section
Setup mode.

On some printer models, the single sheet paper source cannot be

selected since they have been designed for fanfold paper operation
only.

Make sure that the printer is in offline mode; press the Online key, if
Offline Tractor1 necessary.
Park Load Online

1 2 3 4 Press the Park (1) key. If fanfold paper is loaded in the printer, it is fed to
Setup the tear position. The text tear paper off appears in the display. Then
press any key. If a single sheet is loaded in the printer, it is ejected.

BACK PRINT
? QUIT

33
Reference manual Paper handling

Use one of the marked keys to select the desired paper path, for
Single Trac1 example, Single (2).
Online
If you do not make a selection within 5 seconds, the menu
1 2 3 4
Setup is closed.

The printer returns to offline mode. The display alternates between the
basic menu and the menu in the following figure:

Insert a single sheet (for the procedure, see Loading single sheets).
Load paper from
Single Online

1 2 3 4
Setup

Press the Online key to set the printer to ready status. When the printer
Online Single receives data from the computer, the single sheet is automatically
Load Online
loaded. Press the Load (4) key to load the single sheet before starting
1 2 3 4 the printout.
Setup

BACK PRINT
? QUIT

34
 Reference manual Paper handling

➤ Loading paper Your printer can process both fanfold paper and single sheets.

You should only use those paper types which are approved for this
printer. For more information, please refer to Chapter Specifica-
tions, Paper specifications.

Fanfold paper
Make sure that the printer is set for fanfold paper
printing. If necessary, change the paper type (see
Changing the paper type).

Raise the front cover.

Remove the bottom cover A.

Open the right and left tractor flaps.

BACK PRINT
? QUIT

35
Reference manual Paper handling

Release the coloured latch lever of the left-hand trac-

tor and align the tractor so that the first printing
position on the paper matches the X mark on the
printer housing.

Lock the coloured lever again.

Place fanfold paper into the left-hand tractor.

Open the coloured latch lever of the right-hand

tractor and align it to the paper width.
Insert the fanfold paper into the right-hand tractor.
Make sure that it is inserted by the same length as
on the left-hand tractor in order to avoid any paper
jam. Close the tractor flap and lock the tractor by tur-
ning the tractor lever to the rear.

Do not tension the paper excessively to

avoid tearing the perforation holes; do
not allow excessive slack since in this
case the paper will bulge and there may
be problems in the feeding process.

BACK PRINT
? QUIT

36
Reference manual Paper handling

Make sure to align the paper stack in parallel with

the printer and that the paper flow is unobstructed.

90

Re-install the bottom cover.

Online Tractor1
Load Online
Lower the front cover.
1 2 3 4
Setup Switch the printer on. The active paper source (Tractor1) appears in the
display. The paper is automatically loaded when the printer is in online
mode and receives data from the computer.

Press the Load (4) key to load paper before starting the printout.

BACK PRINT
? QUIT

37
 Reference manual Paper handling

Single sheets Some printer models are designed for fanfold paper operation only
and therefore do not feature a single sheet feeder. The front cover
can therefore not be opened on these models.

Make sure that the printer is set to single sheet

mode. If necessary, change the paper type (see
Changing the paper type ).

Press the latch at the middle of the front cover. The

single sheet input tray opens downwards.

BACK PRINT
? QUIT

38
Reference manual Paper handling

Align the left paper guide with the mark on the left of
the single sheet input tray.

Adjust the right paper guide to the width of the paper

used.

BACK PRINT
? QUIT

39
Reference manual Paper handling

Insert the single sheet into the input tray as far as

possible.

Press the Online key to set the printer to ready sta-

tus. The sheet is automatically loaded when the
printer is in online mode and receives data from the
computer.

The printer reports a paper out condition by display-

ing Load paper from single and beeping.

Press the Load (4) key to load paper before starting

the printout.

BACK PRINT
? QUIT

40
Reference manual Paper handling

➤ Paper transport Loaded paper (fanfold paper/single sheets) can be transported in the
printer in several ways.

Make sure that the printer is in offline mode; press the Online key, if ne-
Offline Tractor1 cessary.
Park LF/FF Online

1 2 3 4 Key (2)
Setup Short keypress: Paper is transported upwards step by step
Long keypress: Continuous transport upwards
Key (3)
Short keypress: Paper is transported downwards step by step
Long keypress: Continuous transport downwards
LF/FF key (4)
Short keypress: Line Feed (LF) is executed
Long keypress: Form Feed (FF) is executed

BACK PRINT
? QUIT

41
Reference manual Paper handling

➤ Moving the paper to You can use the Tear (4) key to move the paper to the tear position.
the tear position
Swing the soundproofing cover towards the front.
Online Tractor1
Tear Online
Make sure that the printer is in online mode. If necessary, press the
1 2 3 4 Online key.
Setup
Press the Tear (4) key. The printer moves the perforation edge of the fan-
fold paper to the tear edge. The display alternates between…

Tear position
Tractor1 Online

1 2 3 4
Setup

and…

Online Tear
Exit Online

1 2 3 4
Setup

BACK PRINT
? QUIT

42
Reference manual Paper handling

After having torn off the paper, press the Exit (4)
key. The printer returns the paper to the first printing
position.

If a print job is active, the printer returns the paper

automatically to the first printing position.

BACK PRINT
? QUIT

43
Reference manual Settings

Settings
This section describes how to set the tear position, the first printing line,
the print head gap as well as the font and the character density.

➤ Setting the tear position If the tear position of the paper is not aligned with the tear edge of the
printer, you can adjust it. Inserted paper needs to be torn off if necessary
and retracted to park position.

Press the Setup key. The printer changes to setup mode.

Adjust Paperway
Menu Char Online
Press the Adjust (2) key.
1 2 3 4
Setup

Press the Tear (4) key. The printer executes a formfeed.

TOF
Head Tear Online

1 2 3 4
Setup

BACK PRINT
? QUIT

44
Reference manual Settings

Press the < (2) or > (3) key to move the perforation to the desired posi-
TearAdj= 00/72"* tion. Confirm the input by pressing the Set (1) key.
Set < > Exit Online

1 2 3 4 Confirm the input again by pressing the Setup key. The printer is reset to
Setup the initial status.

The correction made – a maximum of approx. 2.5 cm (1") in

each direction – will be retained after switching the printer
off.
Make sure that the set form length corresponds to the
actual length of the forms you are using.

BACK PRINT
? QUIT

45
 Reference manual Settings

➤ Setting the first printing You can use the TOF function for setting the position of the first printing
line (TOF) line for each paper source and each menu individually.

Before using the TOF function (if fanfold paper is used), you should
first set the tear position (see Setting the tear position).

Open the top cover.

Adjust Paperway
Menu Char Online
Press the Setup key. The printer changes to setup mode.
1 2 3 4
Setup Press the Adjust (2) key.

Press the TOF (3) key. The printer executes a formfeed.

TOF
Head Tear Online

1 2 3 4
Setup

BACK PRINT
? QUIT

46
Reference manual Settings

The paper is fed to the position where the bottom

edge of the first printing line A is aligned with the
A
tear edge B of the printer. The factory setting for the
B
first printing position (TOF) is 12/ 72" (4,23 mm).
This is equivalent to the second line from the top.

r
cke
erdru
m put
Co

Press the < (2) or > (3) key to move the first printing line to the desired
FormAdj= 12/72"* position. You can set values from 0 to 220/72" for fanfold paper or for
Set < > Exit Online
single sheets.
1 2 3 4
Setup

BACK PRINT
? QUIT

47
Reference manual Settings

Confirm the input by pressing the Set (1) key.

FormAdj= 17/72"
Set < > Exit Online
Press the Setup key. The printer returns to the initial status.
1 2 3 4
Setup The setting made will be retained after switching off the
printer.

BACK PRINT
? QUIT

48
 Reference manual Settings

➤ Setting the print The printer features automatic print head gap adjustment to the thick-
head gap ness of the paper used. In setup mode, you can enter a correction value
to modify the head gap determined automatically. This correction is use-
ful for modifying the appearance of the type face and the impact force for
multi-layer paper.

The AGA (automatic gap adjustment) function must be set to “ON”.

For more detailed information, refer to the section Mechanical
adjustments to the printer, Automatic gap adjustment.

Press the Setup key. The printer changes to setup mode.

Adjust Paperway
Menu Char Online
Press the Adjust (2) key.
1 2 3 4
Setup

Press the Head (1) key.

TOF
Head Tear Online

1 2 3 4
Setup

BACK PRINT
? QUIT

49
Reference manual Settings

Use the < (2) or > (3) key to set the range within which the automatic
Head= 0 * gap adjustment is to be corrected. You can select values in the range
Set < > Exit Online
from -10 to +10.
1 2 3 4
Setup Confirm the input by pressing the Set (1) key.

Press the Setup key. The printer returns to the initial status.

Negative values decrease the print head gap, positive values in-
crease it.
The setting made will be retained after switching off the printer.

BACK PRINT
? QUIT

50
Reference manual Settings

➤ Selecting character You can use the CPI (Character Per Inch) key in setup mode to select
density and font the number of characters per inch to be printed. You can use the Font
key to select resident fonts.

Press the Setup key, then the Char (4) key.

Adjust Paperway
Menu Char Online

1 2 3 4
Setup

Press the CPI (3) or Font (2) key (in our example, press CPI).
Font CPI
Online

1 2 3 4
Setup

Use the < (2) or > (3) key to set the desired character density. Confirm
10 CPI * the selection by pressing the Set (1) key.
Set < > Exit Online

1 2 3 4 You can cancel the selection and leave the setting unchanged by pres-
Setup sing the Exit (4) key.

BACK PRINT
? QUIT

51
Reference manual Settings

If you pressed the Font (2) key, use the < (2) or > (3) key to select the
ROMAN NLQ desired font. Confirm the selection by pressing the Set key.
Set < > Exit Online

1 2 3 4 You can cancel the selection and leave the setting unchanged by pres-
Setup sing the Exit (4) key.

Press the Setup key. The printer returns to the initial status.
Adjust Paperway
Menu Char Online
It is also possible to press the Online key. The printer then changes di-
1 2 3 4 rectly to online mode.
Setup
The selection made will not be retained after switching off
the printer. For more details on how to set the character
density and Fonts permanently, please refer to the chapter
Menu.

BACK PRINT
? QUIT

52
Reference manual 2T model

2T model
➤ Introduction This section describes how to handle the rear tractor (paper feed from
the rear), which is only available and permanently installed in the 2T prin-
ter model in addition to the primary tractor (paper feed from the front).

The Paperway parameter group in the menu of the 2T model differs

from the one of the standard printer as follows:

Standard printer 2T model

Paperway Paperway
Single* Single*
Tractor1 (Standard, front) Tractor1 (Standard, front)
Tractor2 (Optional, front) Tractor2 (Optional, front)
Tractor3 (Standard, rear)

The permanently installed rear tractor is identified as “Tractor3” in

the menu. “Tractor2“ in the menu refers to the optional tractor
which can be installed both on the standard printer and the 2T mo-
del. The optional tractor 2 can be installed by the user.

* Not installed on some models.

BACK PRINT
? QUIT

53
 Reference manual 2T model

Rear tractor paper path

Tractor 3

Tract
or 2

Tractor 1

Tractor 1: Standard
Tractor 2: Option, modular

For information on the printable length and width of the forms and
other specifications, refer to Paper specifications.

The 2T model cannot accommodate an additional automatic single

sheet feeder.

BACK PRINT
? QUIT

54
Reference manual 2T model

➤ Loading paper into the To place fanfold paper into the rear tractor, proceed as follows.
rear tractor
Swing the noise absorbing element towards the
front, raise the rear cover vertically and remove it.

Open both the right-hand and left-hand tractor flaps.

BACK PRINT
? QUIT

55
Reference manual 2T model

Release the coloured latch lever of the left-hand trac-

tor and align the tractor in such a way that the first
printing position on the paper matches the X mark
on the printer housing.

Then fix the coloured lever again. Insert fanfold pa-

per into the left-hand tractor.

Release the coloured latch lever of the right-hand

tractor and align it to the paper width. Insert the fan-
fold paper into the right-hand tractor. Make sure that
the paper form is inserted straight in order to avoid
any paper jam. Close the tractor flap and lock the
tractor by turning the lever towards the rear.

Do not tension the paper excessively to

avoid tearing the perforation holes; do
not allow excessive slack since in this
case the paper will bulge and there may
be problems in the feeding process.

BACK PRINT
? QUIT

56
Reference manual 2T model

Darauf achten, daß der Papierstapel parallel zum

Drucker ausgerichtet ist, und daß der Papierfluß
nicht behindert werden kann.

Reinsert the rear cover vertically and lower it to-

wards the rear.

Slide the cover towards the rear to the stop; this will
leave a slot for the paper.

Swing the noise absorbing element back to the rear,

if applicable.

Switch the printer on. It will perform a self-test and

then go to online mode.

Paper may remain inserted in the front

and rear tractors at the same time. This
is made possible by moving the paper in
the inactive tractor automatically to the
parking position whenever changing the
paper path.

BACK PRINT
? QUIT

57
Reference manual 2T model

The active paper source appears in the display. By default, this is the
Online Tractor1 paper path with the front tractor.
Load Online

1 2 3 4 Paper will be loaded automatically when the printer is in online mode and
Setup receives data from the computer.

Press the Load key (4) to load paper before starting the printout.

➤ Paper guiding bracket STOP Important: It is absolutely necessary to mount the paper guiding
bracket when using the rear tractor. It serves to protect the mains
and interface cables from being damaged by the paper in the rear
tractor.

Hook the paper guiding bracket at the bottom of the

printer as shown in the figure and then raise it until it
clicks into place by exerting gentle pressure.

BACK PRINT
? QUIT

58
 Reference manual 2T model

➤ Selecting the rear tractor The rear tractor can be selected either from an application program, the
paper path quick selection or via the setup menu. This chapter describes
the paper path quick selection; for information on how to make the set-
ting in the Setup menu, refer to Setup mode.
Make sure that the printer is in offline mode; press the Online key, if
Offline Tractor1 necessary.
Park Load Online

1 2 3 4 Press the Park key (1). If fanfold paper is loaded in the printer, it is trans-
Setup ported to the tear position. Tear paper will be displayed. Then press any
key. If a single sheet is loaded in the printer, it will be ejected.

Press the Trac3 (4) key to select the rear tractor.

Single Trac1
Trac2 Trac3 Online If you do not make a selection within 5 seconds, the menu
is closed.
1 2 3 4
Setup

The printer returns to offline mode.

The display alternates between the basic menu and:

Load paper from

Tractor3 Online

1 2 3 4
Setup

BACK PRINT
? QUIT

59
Reference manual 2T model

Press the Online key to select the printer. When the printer receives
Online Tractor3 data from the computer, the single sheet will be loaded automatically. To
Load Online
load the single sheet before starting the printout, press the Load key (4).
1 2 3 4
Setup

The fanfold paper can be kept in the inactive tractor when changing
the paper path. The printer will move it automatically to the park
position.

Note that the “Tractor” paper path settings can be selected separa-
tely for each tractor in the “Paperway” parameter group of the se-
tup menu. Settings:
– Form length
– First printing line
– Print head gap setting (only for printers with the AGA automatic
gap adjustment deactivated).

If there is any problem with paper loading or paper transport, proceed as

described in the Troubleshooting chapter.

BACK PRINT
? QUIT

60