7.

Level 2 Repair

7-1. Components on the Rear Case

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair

7-2. Pre-requisite

Tweezers / Disass'y Stick / Screw Driver Anti-static Gloves

Anti-static Mat Hot Plate

A OCTA Disassembly Holder OCTA Disassembly Upper

Ethyl Alcohol Cotton Swab

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair

7-3. Parts which must be changed after repair

BOM description & part

KIT CODE Image Remarks
code

A/S-SVC TAPE BG WP
OUTER
(Common)

[GH81-15875A]

Replace for

Back Glass repair

A/S REWORK KIT-

SM-N960F

[GH82-17460A]
A/S-SVC TAPE BG INNER
NA

[GH81-15876A]

Replace for Back

TAPE FINGER SENSOR Glass
WP
Or Finger print
[GH02-16653A]
sensor repair

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair

7-4. Disassembly

1 1) Put the device in the chamber as 2 Detach the Back Glass. And Finger sensor
following below heating condition 1) Detach the left side of Back glass
- SOC 68%↓: 70℃/10~20 minute 2) Detach the Finger sensor connector
- SOC 68%↑: 70℃/10~20 minute
※ Please confirm the heating condition
released lastly, and follow it.

※ Caution ※ Caution
1) Be care of scratch 1) Be care of scratch

3 Unscrew 18 Point and disassemble SIM Tray 4 Disassemble Upper Rear.

from device (Use disassemble hole left/right side of Rear to
detach it)

Rear Top disassemble hole.

※ Caution
※ Caution
1) Be care of scratch
1) Be care of Rear damage
2) Be care of Rear and connector damage

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair

5 Finally Disassemble Rear of bottom side.

6 Unscrew PBA 3points.
(Use disassemble hole right side of Rear to
detach it)

※ Caution
1) Be care of scratch ※ Caution
2) Be care of Rear and connector damage 1) Be careful not to damage the PBA
3) Be careful not to damage the PBA

7 Disassemble 5 Point connector of PBA. 8 Detach other components.

※ Caution
※ Caution
1) Be care of scratch
2) Be care of connector/cable damage 1) Be care of several kinds of damage

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair

9 Detach Ear Jack 10 Detach SUB PBA

1) Unscrew PBA 1points. 1) Unscrew PBA 2points.
2) Separation of Ear jack Module using Pinset. 2) Separate sub PBA.

※ Caution ※ Caution
1) Be care of Ear jack connector 1) Be care of SUB PBA damage

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair

7-5. Assembly

1 Attach SUB PBA and Ear jack on Front. 2 Screw 3 point in SUB PBA.

※ Caution ※ Caution
1) Be care of chip damage nearby screw point.

3 Attach components on Front. 4 Attach Front CAM, MAIN CAM and Iris CAM on
PBA.
(RCV module, Sensor FPCB, Motor, Battery)

※ Caution
※ Caution
1) Be care of FPCB damage and tilt
1) Be care of press power/time
2) Be care of press power/time

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair

5 Assemble PBA to Front case.

Battery connect and the other connectors. 6 Assemble the Bottom REAR in sequence.
(5 Point)
* Torque Value : 1.2±0.1kgfcm

※ Caution ※ Caution
1) Be care of scratch and REAR damage 1) Be care of scratch and REAR damage
2) Check for contact damage.(red area) 2) Check for contact damage.(red area)

7 `
Assemble the TOP+MID REAR Assy in 8 Screw insertion 18 Point.
sequence. * Torque Value : 1.2±0.1kgfcm

※ Caution
※ Caution
1) Be care of scratch and REAR damage 1) Be care of Rear damage
2) Check for contact damage.(red area)

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair

9 Press the S-Pen cover using pressing jig 10 Attach the finger sensor on the REAR and
and pad. Assemble the finger sensor on the PBA
- Pressing force : 1 N
(It is set on the pressing jig in advance)
- Pressing tine : 5 sec

※ Caution
※ Caution
1) Do NOT press a S-Pen cover over 5 seconds to prevent
display damage. 1) Be care of scratch and tilt.

11 Attach the back glass inner tape on the 12 Attach the finger tape on the back glass.
back glass.

※ Caution ※ Caution
1) Be care of scratch and tilt. 1) Be care of scratch and tilt.

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
7. Level 2 Repair

13 Attach the back glass outside tape on the rear 14 Attach the back glass on the REAR side.
case.
Attach the back glass outside tape on the rear
case by hands.
Gently press all adhesive parts of tape using
disassembly stick or hands.

※ Caution ※ Caution
1) Fit the tapes precisely to the screw and finger print sensor 1) Be care of scratch and tilt.
holes of rear case.

15 Press Back Glass.

- Pressing force : 1 N
- Pressing time : 1 minute
SIM Tray must be seperated before
pressing the backglass or the OCTA

※ Caution
1) Be care of scratch.

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.