Electronic Devices and Circuits Lab

ELECTRONIC DEVICES AND CIRCUITS
LABORATORY MANUAL
B.TECH
(II YEAR – I SEM)
(2021-22)
Prepared by:
Mr. R.ChinnaRao Associate Professor
Mr V .Shiva Rajkumar, Assistant Professor
Mr E. Mahendar Reddy, Assistant Professor
Department of Electronics and Communication Engineering
MALLA REDDY COLLEGE

OF ENGINEERING & TECHNOLOGY
(Autonomous Institution – UGC, Govt. of India)
Recognized under 2(f) and 12 (B) of UGC ACT 1956
Affiliated to JNTUH, Hyderabad, Approved by AICTE - Accredited by NBA & NAAC – ‘A’ Grade - ISO 9001:2015 Certified)
Maisammaguda, Dhulapally (Post Via. Kompally), Secunderabad – 500100, Telangana State, India
Electronic devices and circuits Lab Manual ECE, MRCET
VISION
MISSION
QUALITY POLICY
PROGRAMME EDUCATIONAL OBJECTIVES

PEO1: PROFESSIONALISM & CITIZENSHIP
To create and sustain a community of learning in which students
acquire knowledge and learn to apply it professionally with due
consideration for ethical, ecological and economic issues.
PEO2: TECHNICAL ACCOMPLISHMENTS

To provide knowledge based services to satisfy the needs of society and
the industry by providing hands on experience in various technologies
in core field.
PEO3: INVENTION, INNOVATION AND CREATIVITY

To make the students to design, experiment, analyze, interpret in the
core field with the help of other multi disciplinary concepts wherever
applicable.
PEO4: PROFESSIONAL DEVELOPMENT

To educate the students to disseminate research findings with good
soft skills and become a successful entrepreneur.
PEO5: HUMAN RESOURCE DEVELOPMENT

To graduate the students in building national capabilities in technology,
education and research.
CODE OF CONDUCT FOR THE LABORATORIES


All students must observe the Dress Code while in the laboratory.

Sandals or open-toed shoes are NOT allowed.

Foods, drinks and smoking are NOT allowed.

All bags must be left at the indicated place.

The lab timetable must be strictly followed.

Be PUNCTUAL for your laboratory session.

Program must be executed within the given time.

Noise must be kept to a minimum.

Workspace must be kept clean and tidy at all time.

Handle the systems and interfacing kits with care.

All students are liable for any damage to the accessories due to their own negligence.

All interfacing kits connecting cables must be RETURNED if you taken from the lab supervisor.

Students are strictly PROHIBITED from taking out any items from the laboratory. 

Students are NOT allowed to work alone in the laboratory without the Lab Supervisor

USB Ports have been disabled if you want to use USB drive consult lab supervisor.

Report immediately to the Lab Supervisor if any malfunction of the accessories, is there.
Before leaving the lab

Place the chairs properly.

Turn off the system properly

Turn off the monitor. 

Please check the laboratory notice board regularly for updates.
EDC Lab Manual ECE, MRCET
BASIC REQUIREMENT FOR EDC LAB
PART A: Only For Viva- Voice Examination Electronic Work Shop Practice
1) Identification, Specifications, Testing of R, L, C Components (Color Codes), Potentiometers,
Switches (SPDT, DPDT, and DIP), Coils, Gang Condensers, Relays, Bread Boards, PCB’s
2) Identification, Specifications and Testing of Active Devices, Diodes, BJT’s, Low power
JFET’s, MOSFET’s, Power Transistors, LED’s, LCD’s, UJT.
3) Study and operation of
a) Multi meters (Analog and Digital)
b) Function Generator
c) Regulated Power Supplies
d) CRO.
5
LIST OF EXPERIMENTS
PART B: (For Laboratory Examination – Minimum of 10 experiments)
1) P-N junction diode forward and reverse bias characteristics. 33
2) Zener diode characteristics and Zener as voltage regulator. 37
3) Half –Wave Rectifier without and with capacitor filter. 42
4) Full – Wave Rectifier without and with capacitor filter. 47
5) Input and output characteristics of a BJT in CE configuration. 52
6) Measurement of h – parameters in CE configuration. 56
7) Frequency response of CE amplifier. 60
8) Feedback amplifiers: Voltage series and current shunt 64
9) RC phase shift oscillator using transistors. 67
10) Hartley & Colpitts oscillator using transistors. 70
11) Frequency response of common source JFET amplifier. 76
12) UJT Characteristics. 80
6
1. BASIC ELECTRONIC COMPONENTS

COLOUR CODING OF RESISTOR:
Colour Codes are used to identify the value of resistor. The numbers to the Colour are
identified in the following sequence which is remembered as BBROY GREAT
BRITAN VERY GOOD WIFE (BBROYGBVGW) and their assignment is listed in
following table.
Black Brown Red Orange Yellow Green Blue Violet Grey White
0 1 2 3 4 5 6 7 8 9
Table1: Colour codes of resistor
First find the tolerance band, it will typically be gold ( 5%) and
sometimes silver (10%).
Starting from the other end, identify the first band - write down the
number associated with that color
Now read the next color, so write down a its value next to the first value.
Now read the third or 'multiplier exponent' band and write down that as
the number of zeros.
If the 'multiplier exponent' band is Gold move the decimal point one to
the left. If the 'multiplier exponent' band is Silver move the decimal point
two places to the left. If the resistor has one more band past the tolerance
band it is a quality band.
Read the number as the '% Failure rate per 1000 hour' This is rated
assuming full wattage being applied to the resistors. (To get better failure
rates, resistors are typically specified to have twice the needed wattage
dissipation that the circuit produces). Some resistors use this band for
temco information. 1% resistors have three bands to read digits to the
left of the multiplier. They have a different temperature coefficient in
order to provide the 1% tolerance. At 1% the temperature coefficient
starts to become an important factor. at +/-200 ppm a change in
temperature of 25 Deg C causes a value change of up to 1%
Table2: Procedure to find the value of resistor using colour codes
7
COLOUR CODING OF CAPACITORS
An electrical device capable of storing electrical energy. In general, a capacitor consists

of two metal plates insulated from each other by a dielectric. The capacitance of a
capacitor depends primarily upon its shape and size and upon the relative permittivity εr
of the medium between the plates. In vacuum, in air, and in most gases, εr ranges from
one to several hundred.
One classification of capacitors comes from the physical state of their dielectrics, which
may be gas (or vacuum), liquid, solid, or a combination of these. Each of these
classifications may be subdivided according to the specific dielectric used. Capacitors
may be further classified by their ability to be used in alternating-current (ac) or direct-
current (dc) circuits with various current levels.
 Capacitor Identification Codes: There are no international agreements in place to

standardize capacitor identification. Most plastic film types (Figure1) have printed
values and are normally in microfarads or if the symbol is n, Nanofarads. Working
voltage is easily identified. Tolerances are upper case letters: M = 20%, K = 10%, J =
5%, H = 2.5% and F = ± 1pF.
Figure 1: Plastic Film Types
A more difficult scheme is shown in Figure 2 where K is used for indicating Picofarads.
The unit is picofarads and the third number is a multiplier. A capacitor coded 474K63
means 47 × 10000 pF which is equivalent to 470000 pF or 0.47 microfarads. K indicates
10% tolerance. 50, 63 and 100 are working volts.
8
Figure 2: Picofarads Representation
Ceramic disk capacitors have many marking schemes. Capacitance, tolerance, working
voltage and temperature coefficient may be found which is as shown in figure 3.
Capacitance values are given as number without any identification as to units. (uF, nF,
pF) Whole numbers usually indicate pF and decimal numbers such as 0.1 or 0.47 are
microfarads. Odd looking numbers such as 473 is the previously explained system and
means 47nf
Figure3: Ceramic Disk Capacitor
9
Figure 4 shows some other miscellaneous schemes.
Figure 4: Miscellaneous Schemes.
 Electrolytic capacitor properties

There are a number of parameters of importance beyond the basic capacitance and
capacitive reactance when using electrolytic capacitors. When designing circuits using
electrolytic capacitors it is necessary to take these additional parameters into
consideration for some designs, and to be aware of them when using electrolytic
capacitors
 ESR Equivalent series resistance: Electrolytic capacitors are often used in circuits
where current levels are relatively high. Also under some circumstances and current
sourced from them needs to have low source impedance, for example when the
capacitor is being used in a power supply circuit as a reservoir capacitor. Under these
conditions it is necessary to consult the manufacturers’ datasheets to discover whether
the electrolytic capacitor chosen will meet the requirements for the circuit. If the ESR
is high, then it will not be able to deliver the required amount of current in the circuit,
without a voltage drop resulting from the ESR which will be seen as a source
resistance.
 Frequency response: One of the problems with electrolytic capacitors is that they
have a limited frequency response. It is found that their ESR rises with frequency and
this generally limits their use to frequencies below about 100 kHz. This is particularly
true for large capacitors, and even the smaller electrolytic capacitors should not be
relied upon at high frequencies. To gain exact details it is necessary to consult the
manufacturer’s data for a given part.
10
 Leakage: Although electrolytic capacitors have much higher levels of capacitance

for a given volume than most other capacitor technologies, they can also have a
higher level of leakage. This is not a problem for most applications, such as when
they are used in power supplies. However under some circumstances they are not
suitable. For example they should not be used around the input circuitry of an
operational amplifier. Here even a small amount of leakage can cause problems
because of the high input impedance levels of the op-amp. It is also worth noting that
the levels of leakage are considerably higher in the reverse direction.
 Ripple current: When using electrolytic capacitors in high current applications
such as the reservoir capacitor of a power supply, it is necessary to consider the ripple
current it is likely to experience. Capacitors have a maximum ripple current they can
supply. Above this they can become too hot which will reduce their life. In extreme
cases it can cause the capacitor to fail. Accordingly it is necessary to calculate the
expected ripple current and check that it is within the manufacturer’s maximum
ratings.
 Tolerance: Electrolytic capacitors have a very wide tolerance. Typically this may be
-50% + 100%. This is not normally a problem in applications such as decoupling or
power supply smoothing, etc. However they should not be used in circuits where the
exact value is of importance.
 Polarization: Unlike many other types of capacitor, electrolytic capacitors are
polarized and must be connected within a circuit so that they only see a voltage across
them in a particular way.
The physical appearance of electrolytic capacitor is as shown in Figure 5.The capacitors

themselves are marked so that polarity can easily be seen. In addition to this it is common
for the can of the capacitor to be connected to the negative terminal.
Figure 5: Electrolytic Capacitor
It is absolutely necessary to ensure that any electrolytic capacitors are connected

within a circuit with the correct polarity. A reverse bias voltage will cause the centre
oxide layer forming the dielectric to be destroyed as a result of electrochemical reduction.
If this occurs a short circuit will appear and excessive current can cause the capacitor to
become very hot. If this occurs the component may leak the electrolyte, but under some
circumstances they can explode. As this is not uncommon, it is very wise to take
precautions and ensure the capacitor is fitted correctly, especially in applications where
high current capability exists.
11
COLOUR CODING OF INDUCTORS
Inductor is just coil wound which provides more reactance for high frequencies and low
reactance for low frequencies.
Molded inductors follow the same scheme except the units are usually micro
henries. A brown-black-red inductor is most likely a 1000 uH. Sometimes a silver or gold
band is used as a decimal point. So a red-gold-violet inductor would be a 2.7 uH. Also
expect to see a wide silver or gold band before the first value band and a thin tolerance
band at the end. The typical Colour codes and their values are shown in Figure 6.
1000uH (1millihenry), 2%
6.8 uH, 5%
Figure 6: Typical inductors colour coding and their values.
12
2. CIRCUIT SYMBOLS
WIRES AND CONNECTIONS
S.NO COMPONENT CIRCUIT SYMBOL FUNCTION

NAME
To pass current very easily
1 WIRE from one part of a circuit to
another.
A 'blob' should be drawn

where wires are connected
(joined), but it is sometimes
2 WIRES JOINED omitted. Wires connected at
'crossroads' should be
staggered slightly to form
two T-junctions, as shown on
the right.
In complex diagrams it is
often necessary to draw
wires crossing even though
3 WIRES NOT they are not connected. I
JOINED prefer the 'bridge' symbol
shown on the right because
the simple crossing on the
left may be misread as a join
where you have forgotten to
add a 'blob'.
POWER SUPPLIES

NAME
Supplies electrical energy.
The larger terminal (on the
1 CELL left) is positive (+).
A single cell is often called a
battery, but strictly a battery
is two or more cells joined
together
Supplies electrical energy. A
battery is more than one cell.
2 BATTERY The larger terminal (on the
left) is positive (+).
13

3 DC SUPPLY DC = Direct Current, always
flowing in one direction.
4 AC SUPPLY AC = Alternating Current,
continually changing
direction.
A safety device which will
'blow' (melt) if the current
5 FUSE
flowing through it exceeds a
specified value.
Two coils of wire linked by
an iron core. Transformers
are used to step up (increase)
and step down (decrease) AC
6 TRANSFORMER voltages. Energy is
transferred between the coils
by the magnetic field in the
core. There is no electrical
connection between the coils.
A connection to earth. For
many electronic circuits this
is the 0V (zero volts) of the
7 EARTH(GROUND) power supply, but for mains
electricity and some radio
circuits it really means the
earth. It is also known as
ground.
Output Devices: Lamps, Heater, Motor, etc.

NAME
A transducer which converts
electrical energy to light.
1 LAMP(LIGHTING) This symbol is used for a
lamp providing illumination,
for example a car headlamp
or torch bulb
electrical energy to light.
2 LAMP(INDICATOR) This symbol is used for a
lamp which is an indicator,
for example a warning light
on a car dashboard.
3 HEATER A transducer which converts
electrical energy to heat.
14

4 MOTOR electrical energy to kinetic
energy (motion).
5 BELL A transducer which converts

electrical energy to sound.
6 BUZZER A transducer which converts

electrical energy to sound.
A coil of wire which creates

a magnetic field when
current passes through it. It
7 INDUCTOR(SOLIN may have an iron core inside
OID,COIL) the coil. It can be used as a
transducer converting
electrical energy to
mechanical energy by
pulling on something.
Switches

NAME
1 PUSH A push switch allows current
SWITCH(PUSH TO to flow only when the button
MAKE) is pressed. This is the switch
used to operate a doorbell.
This type of push switch is
2 PUSH TO BREAK
normally closed (on), it is
SWITCH
open (off) only when the
button is pressed.
SPST = Single Pole, Single
3 ON/OFF Throw.
SWITCH(SPST) An on-off switch allows
current to flow only when it
is in the closed (on) position.
SPDT = Single Pole, Double
Throw. A 2-way changeover
4 2 WAY switch directs the flow of
SWITCH(SPDT) current to one of two routes
according to its position.
Some SPDT switches have a
central off position and are
described as 'on-off-on'.
15
DPST = Double Pole, Single

Throw.
5 DUAL ON-OFF A dual on-off switch which
SWITCH(DPST) is often used to switch mains
electricity because it can
isolate both the live and
neutral connections.
DPDT = Double Pole,

Double Throw.
6 REVERSING This switch can be wired up
SWITCH(DPDT) as a reversing switch for a
motor. Some DPDT switches
have a central off position.
An electrically operated
switch, for example a 9V
battery circuit connected to
7 RELAY the coil can switch a 230V
AC mains circuit.
NO = Normally Open,
COM = Common,
NC = Normally Closed.
RESISTORS

NAME
A resistor restricts the flow
of current, for example to
limit the current passing
1 RESISTOR
Or through an LED. A resistor is
used with a capacitor in a
timing circuit.
This type of variable resistor
with 2 contacts (a rheostat) is
usually used to control
2 current. Examples include:
VARIABLE
adjusting lamp brightness,
RESISTOR(RHEOST
adjusting motor speed, and
AT)
adjusting the rate of flow of
charge into a capacitor in a
timing circuit.
3 VARIABLE This type of variable resistor

RESISTOR(POTENT with 3 contacts (a
IOMETER) potentiometer) is usually
16
used to control voltage. It

can be used like this as a
transducer converting
position (angle of the control
spindle) to an electrical
signal
This type of variable resistor
(a preset) is operated with a
small screwdriver or similar
tool. It is designed to be set
4 VARIABLE when the circuit is made and
RESISTER(PRESET) then left without further
adjustment. Presets are
cheaper than normal variable
resistors so they are often
used in projects to reduce the
cost
CAPACITORS
S.NO NAME OF THE FUNCTION OF THE

CIRCUIT SYMBOL
COMPONENT COMPONENT
A capacitor stores electric
charge. A capacitor is used
with a resistor in a timing
1 CAPACITOR circuit. It can also be used
as a filter, to block DC
signals but pass AC
signals.
A capacitor stores electric
charge.This type must be
connected the correct way
round. A capacitor is used
CAPACITOR
2 with a resistor in a timing
POLARISED
circuit. It can also be used
as a filter, to block DC
Signals but pass AC
signals.
A variable capacitor is
VARIABLE
3 used in a radio tuner.
CAPACITOR
17
This type of variable

capacitor (a trimmer) is
operated with a small
4 TRIMMER screwdriver or similar tool.
CAPACITOR It is designed to be set
when the circuit is made
and then left without
further adjustment
DIODES

CIRCUIT SYMBOL
COMPONENT COMPONENT
A device which only
1 DIODE allows current to flow in
one direction
A transducer which
LED(LIGHT
2 converts electrical energy
EMITTING DIODE)
to light.
A special diode which is
3 ZENER DIODE used to maintain a fixed
voltage across its terminals
4 PHOTO DIODE A light-sensitive diode.
TRANSISTORS

CIRCUIT SYMBOL
COMPONENT COMPONENT
A transistor amplifies
current. It can be used with
other components to make
1 TRANSISTOR NPN
an amplifier or switching
circuit.
A transistor amplifies
current. It can be used with
2 other components to make
TRANSISTOR PNP
an amplifier or switching
circuit.
18
A light-sensitive transistor.
PHOTO
3
TRANSISTOR
AUDIO AND RADIO DEVICES

CIRCUIT SYMBOL
COMPONENT COMPONENT
A transducer which
1 MICROPHONE converts sound to electrical
energy.
A transducer which
2
EARPHONE converts electrical energy
to sound.
A transducer which
3 LOUD SPEAKER converts electrical energy
to sound.
A transducer which
4 PIEZO
converts electrical energy
TRANSDUCER
to sound.
An amplifier circuit with
one input. Really it is a
5 AMPLIFIER(GENER block diagram symbol
AL SYMBOL) because it represents a
circuit rather than just one
component.
A device which is designed
to receive or transmit radio
6 ARIEL (ANTENNA) signals. It is also known as
an antenna

CIRCUIT SYMBOL
COMPONENT COMPONENT
A voltmeter is used to
measure voltage. The
1 Proper name for voltage is
VOLTMETER
'potential difference', but
most people prefer to say
voltage.
19
An ammeter is used to
2 AMMETTER
measure current
A galvanometer is a very
sensitive meter which is
3 GALVANOMETER used to measure tiny
currents, usually 1mA or
less
An ohmmeter is used to
measure resistance. Most
OHMMETER
4 multimeters have an
ohmmeter setting.
An oscilloscope is used to
display the shape of
5 OSCILLOSCOPE electrical signals and it can
be used to measure their
voltage and time period.
Sensors (input devices)

CIRCUIT SYMBOL
COMPONENT COMPONENT
A transducer which
converts brightness (light)
1 LDR to resistance (an electrical
property). LDR = Light
Dependent Resistor
A transducer which
converts temperature (heat)
2 THERMISTOR to resistance (an electrical
property).
20
3. STUDY OF CRO
An oscilloscope is a test instrument which allows us to look at the 'shape' of electrical
signals by displaying a graph of voltage against time on its screen. It is like a voltmeter
with the valuable extra function of showing how the voltage varies with time. A graticule
with a 1cm grid enables us to take measurements of voltage and time from the screen.
The graph, usually called the trace, is drawn by a beam of electrons striking the phosphor
coating of the screen making it emit light, usually green or blue. This is similar to the
way a television picture is produced.
Oscilloscopes contain a vacuum tube with a cathode (negative electrode) at one end to
emit electrons and an anode (positive electrode) to accelerate them so they move rapidly
down the tube to the screen. This arrangement is called an electron gun. The tube also
contains electrodes to deflect the electron beam up/down and left/right.
The electrons are called cathode rays because they are emitted by the cathode and this
gives the oscilloscope its full name of cathode ray oscilloscope or CRO.
A dual trace oscilloscope can display two traces on the screen, allowing us to easily
compare the input and output of an amplifier for example. It is well worth paying the
modest extra cost to have this facility.
Figure1: Front Panel of CRO
21
 BASIC OPERATION:
Electron gun Y plates
Cathode
Fluorescent screen
Electron beam
Anode
X plates
Figure2: Internal Blocks of CRO
 Setting up an oscilloscope:
Oscilloscopes are complex instruments with many controls and they require some care to
set up and use successfully. It is quite easy to 'lose' the trace off the screen if controls are
set wrongly.
There is some variation in the arrangement and labeling of the many controls so the
following instructions may need to be adapted for this instrument.
1. Switch on the oscilloscope to warm up (it takes a minute or two).

2. Do not connect the input lead at this stage.
3. Set the AC/GND/DC switch (by the Y INPUT) to DC.
4. Set the SWP/X-Y switch to SWP (sweep).
5. Set Trigger Level to AUTO.
6. Set Trigger Source to INT (internal, the y input).
7. Set the Y AMPLIFIER to 5V/cm (a moderate value).
8. Set the TIMEBASE to 10ms/cm (a moderate speed).
9. Turn the time base VARIABLE control to 1 or CAL.
10. Adjust Y SHIFT (up/down) and X SHIFT (left/right) to give a trace across the
middle of the screen, like the picture.
11. Adjust INTENSITY (brightness) and FOCUS to give a bright, sharp trace.
22
The following type of trace is observed on CRO after setting up, when there is no
input signal connected.
Figure 3: Absence of input signal
 Connecting an oscilloscope:
The Y INPUT lead to an oscilloscope should be a co-axial lead and the figure 4 shows its
construction. The central wire carries the signal and the screen is connected to earth (0V)
to shield the signal from electrical interference (usually called noise).
Figure 4: Construction of a co-axial lead
Most oscilloscopes have a BNC socket for the y input and the lead is connected with a
push and twist action, to disconnect we need to twist and pull. Professionals use a
specially designed lead and probes kit for best results with high frequency signals and
when testing high resistance circuits, but this is not essential for simpler work at audio
frequencies (up to 20 kHz).
23
Figure 5: Oscilloscope lead and probes kit
 Obtaining a clear and stable trace:
Once if we connect the oscilloscope to the circuit, it is necessary to adjust the controls to
obtain a clear and stable trace on the screen in order to test it.
 The Y AMPLIFIER (VOLTS/CM) control determines the height of the trace.

Choose a setting so the trace occupies at least half the screen height, but does not
disappear off the screen. 
 The TIMEBASE (TIME/CM) control determines the rate at which the dot sweeps
across the screen. Choose a setting so the trace shows at least one cycle of the
signal across the screen. Note that a steady DC input signal gives a horizontal line
trace for which the time base setting is not critical. 
 The TRIGGER control is usually best left set to AUTO.
24
The trace of an AC signal with the oscilloscope controls correctly set is as shown in
Figure 6.
Figure 6 : Stable waveform
 Measuring voltage and time period
The trace on an oscilloscope screen is a graph of voltage against time. The shape of this
graph is determined by the nature of the input signal. In addition to the properties labeled
on the graph, there is frequency which is the number of cycles per second. The diagram
shows a sine wave but these properties apply to any signal with a constant shape
Figure7: Properties of trace
25
 Amplitude is the maximum voltage reached by the signal. It is measured in volts.

 Peak voltage is another name for amplitude.
 Peak-peak voltage is twice the peak voltage (amplitude). When reading an
oscilloscope trace it is usual to measure peak-peak voltage.
 Time period is the time taken for the signal to complete one cycle.
It is measured in seconds (s), but time periods tend to be short so milliseconds (ms)
and microseconds (µs) are often used. 1ms = 0.001s and 1µs = 0.000001s.
 Frequency is the number of cycles per second. It is measured in hertz (Hz), but
frequencies tend to be high so kilohertz (kHz) and megahertz (MHz) are often used.
1kHz = 1000Hz and 1MHz = 1000000Hz.
Frequency = 1 Time
period
Time period = 1
Frequency
A) Voltage: Voltage is shown on the vertical y-axis and the scale is determined by the
Y AMPLIFIER (VOLTS/CM) control. Usually peak-peak voltage is measured because it
can be read correctly even if the position of 0V is not known. The amplitude is half the
peak-peak voltage.
Voltage = distance in cm × volts/cm
B) Time period: Time is shown on the horizontal x-axis and the scale is determined
by the TIMEBASE (TIME/CM) control. The time period (often just called period) is the
time for one cycle of the signal. The frequency is the number of cycles per second,
frequency = 1/time period.
Time = distance in cm × time/cm
26
4. STUDY OF FUNCTION GENERATOR

A function generator is a device that can produce various patterns of voltage at a variety
of frequencies and amplitudes. It is used to test the response of circuits to common input
signals. The electrical leads from the device are attached to the ground and signal input
terminals of the device under test.
Figure 1: A typical low-cost function generator.
 Features and controls :
Most function generators allow the user to choose the shape of the output from a small
number of options.
 Square wave - The signal goes directly from high to low voltage.
Figure 2: Square wave
27
The duty cycle of a signal refers to the ratio of high voltage to low voltage time in a
square wave signal.
 Sine wave - The signal curves like a sinusoid from high to low voltage.
Figure3: Sine Wave
 Triangle wave - The signal goes from high to low voltage at a fixed rate.
Figure 4: Triangular Wave
The amplitude control on a function generator varies the voltage difference between the
high and low voltage of the output signal. The direct current (DC) offset control on a
function generator varies the average voltage of a signal relative to the ground.
28
The frequency control of a function generator controls the rate at which output signal
oscillates. On some function generators, the frequency control is a combination of
different controls. One set of controls chooses the broad frequency range (order of
magnitude) and the other selects the precise frequency. This allows the function generator
to handle the enormous variation in frequency scale needed for signals.
 How to use a function generator
After powering on the function generator, the output signal needs to be configured to the
desired shape. Typically, this means connecting the signal and ground leads to an
oscilloscope to check the controls. Adjust the function generator until the output signal is
correct, then attach the signal and ground leads from the function generator to the input
and ground of the device under test. For some applications, the negative lead of the
function generator should attach to a negative input of the device, but usually attaching to
ground is sufficient.
29
5. STUDY OF REGULATED POWER SUPPLY

There are many types of power supply. Most are designed to convert high voltage AC
mains electricity to a suitable low voltage supply for electronic circuits and other devices.
A power supply can by broken down into a series of blocks, each of which performs a
particular function. For example a 5V regulated supply:
Figure1: Block Diagram Of Regulated Power Supply
Each of the blocks is described in more detail below:
 Transformer: Steps down high voltage AC mains to low voltage AC.

 Rectifier: Converts AC to DC, but the DC output is varying.
 Smoothing: Smooths the DC from varying greatly to a small ripple.
 Regulator: Eliminates ripple by setting DC output to a fixed voltage.
 Dual Supplies: Some electronic circuits require a power supply with positive and
negative outputs as well as zero volts (0V). This is called a 'dual supply' because it is
like two ordinary supplies connected together as shown in the diagram. Dual supplies
have three outputs, for example a ±9V supply has +9V, 0V and -9V outputs.
Figure 2: Dual Supply
30
6. TYPES OF CIRCUIT BOARD

 Breadboard: This is a way of making a temporary circuit, for testing purposes or
to try out an idea. No soldering is required and all the components can be re-used
afterwards. It is easy to change connections and replace components. Almost all
the Electronics Club projects started life on a breadboard to check that the circuit
worked as intended. The following figure depicts the appearance of Bread board
in which the holes in top and bottom stribes are connected horizontally that are
used for power supply and ground connection conventionally and holes on middle
stribes connected vertically. And that are used for circuit connections
conventionally.
Figure 1: Bread board
 Strip board:
Figure 2: Strip Board
31
Stripboard has parallel strips of copper track on one side. The strips are 0.1" (2.54mm)
apart and there are holes every 0.1" (2.54mm). Stripboard requires no special preparation
other than cutting to size. It can be cut with a junior hacksaw, or simply snap it along the
lines of holes by putting it over the edge of a bench or table and pushing hard.
Printed Circuit Board: A printed circuit board, or PCB, is used to mechanically support
and electrically connect electronic components using conductive pathways, tracks or
traces etched from copper sheets laminated onto a non-conductive substrate. It is also
referred to as printed wiring board (PWB) or etched wiring board. A PCB populated with
electronic components is a printed circuit assembly (PCA), also known as a printed
circuit board assembly (PCBA).
Printed circuit boards have copper tracks connecting the holes where the
components are placed. They are designed especially for each circuit and make
construction very easy. However, producing the PCB requires special equipment so this
method is not recommended if you are a beginner unless the PCB is provided for you.
Figure 3: Printed circuit board
PCBs are inexpensive, and can be highly reliable. They require much more layout effort
and higher initial cost than either wire-wrapped or point-to-point constructed circuits, but
are much cheaper and faster for high-volume production. Much of the electronics
industry's PCB design, assembly, and quality control needs are set by standards that are
published by the IPC organization.
32
1. P-N JUNCTION DIODE CHARACTERISTICS
AIM: 1. To observe and draw the Forward and Reverse bias V-I Characteristics of a P-N
Junction diode.
2. To calculate static and dynamic resistance in both forward and Reverse Bias
Condition.
APPARATUS:
1. P-N Diode IN4007 - 1No.

2. Regulated Power supply (0-30V) - 1No.
3. Resistor 1KΩ - 1No.
4. Ammeter (0-20 mA) - 1No
5. Ammeter (0-200µA) - 1No.
6. Voltmeter (0-20V) - 2No.
7. Bread board
8. Connecting wires
THEORY:
A P-N junction diode conducts only in one direction. The V-I characteristics of
the diode are curve between voltage across the diode and current flowing through the
diode. When external voltage is zero, circuit is open and the potential barrier does not
allow the current to flow. Therefore, the circuit current is zero. When P-type (Anode) is
connected to +ve terminal and n- type (cathode) is connected to –ve terminal of the
supply voltage is known as forward bias. The potential barrier is reduced when diode is in
the forward biased condition. At some forward voltage, the potential barrier altogether
eliminated and current starts flowing through the diode and also in the circuit. Then diode
is said to be in ON state. The current increases with increasing forward voltage.
When N-type (cathode) is connected to +ve terminal and P-type (Anode) is

connected –ve terminal of the supply voltage is known as reverse bias and the potential
barrier across the junction increases. Therefore, the junction resistance becomes very
high and a very small current (reverse saturation current) flows in the circuit. Then diode
is said to be in OFF state. The reverse bias current is due to minority charge carriers.
33
CIRCUIT DIAGRAM:
A) Forward bias:
B) Reverse Bias:
MODEL GRAPH:
34
OBSERVATIONS:
A) FORWARD BIAS:
S.NO Applied Forward Forward

Voltage(V) Voltage(Vf) Current(If(mA))
B) REVERSE BIAS:
S.NO Applied Reverse Reverse

Voltage(V) Voltage(VR) Current(IR(µA))
Calcutions:
Calculation of Static and Dynamic Resistance for a given diode.
In forward bias condition:
Static Resistance , Rs = Vf/If =

Dynamic Resistance, RD = ∆Vf/ ∆If =
In Reverse bias condition:
Static Resistance , Rs = VR/IR =

Dynamic Resistance, RD = ∆VR/ ∆IR =
35
PROCEDURE:
A) FORWARD BIAS:
1. Connections are made as per the circuit diagram.
2. for forward bias, the RPS +ve is connected to the anode of the diode and
RPS –ve is connected to the cathode of the diode
3. Switch on the power supply and increases the input voltage (supply voltage) in
Steps of 0.1V
4. Note down the corresponding current flowing through the diode and voltage
across the diode for each and every step of the input voltage.
5. The reading of voltage and current are tabulated.
6. Graph is plotted between voltage (Vf) on X-axis and current (If) on Y-axis.
B) REVERSE BIAS:
1. Connections are made as per the circuit diagram

2. For reverse bias, the RPS +ve is connected to the cathode of the diode and
RPS –ve is connected to the anode of the diode.
3. Switch on the power supply and increase the input voltage (supply voltage) in
Steps of 1V.
4. Note down the corresponding current flowing through the diode voltage across
the diode for each and every step of the input voltage.
5. The readings of voltage and current are tabulated
6. Graph is plotted between voltage (VR) on X-axis and current (IR) on Y-axis.
PRECAUTIONS:
1. All the connections should be correct.

2. Parallax error should be avoided while taking the readings from the Analog meters.
RESULT:
VIVA QUESTIONS:
1. Define depletion region of a diode?
2. What is meant by transition & space charge capacitance of a diode?
3. Is the V-I relationship of a diode Linear or Exponential?
4. Define cut-in voltage of a diode and specify the values for Si and Ge diodes?
5. What are the applications of a p-n diode?
6. Draw the ideal characteristics of P-N junction diode?
7. What is the diode equation?
8. What is PIV?
9. What is the break down voltage?
10. What is the effect of temperature on PN junction diodes?
11. Specifications of diodes
36
2. ZENER DIODE CHARACTERISTICS AND ZENER AS

VOLTAGE REGULATOR
AIM:
a) To observe and draw the static characteristics of a zener diode

b) To find the voltage regulation of a given zener diode
APPARATUS:
1. Zener diode - 1No.

2. Regulated Power Supply (0-30v) - 1No.
3. Voltmeter (0-20v) - 1No.
4. Ammeter (0-20mA) - 1No.
5. Resistor (1K ohm)
6. Bread Board
7. Connecting wires
THEORY:
A zener diode is heavily doped p-n junction diode, specially made to operate in
the break down region. A p-n junction diode normally does not conduct when reverse
biased. But if the reverse bias is increased, at a particular voltage it starts conducting
heavily. This voltage is called Break down Voltage. High current through the diode can
permanently damage the device.
To avoid high current, we connect a resistor in series with zener diode. Once the
diode starts conducting it maintains almost constant voltage across the terminals
whatever may be the current through it, i.e., it has very low dynamic resistance. It is
used in voltage regulators.
37
CIRCUIT DIAGRAM
A) STATIC CHARACTERISTICS :
b) REVERSE BIAS CHARACTERISTICS:
38
OBSERVATIONS:
A) FORWARD BIAS Characteristics:
S.NO Applied Voltage(V) Forward Voltage(Vf) Forward Current(If(mA))
B) REVERSE BIAS Characteristics:
S.NO Applied Voltage(V) Reverse Voltage(VR) Reverse Current(IR(mA))
39
PROCEDURE:
A) Static characteristics:

2. The Regulated power supply voltage is increased in steps.
3. The Forward current (lf), and the forward voltage (Vf.) are observed and then
noted in the tabular form.
4. A graph is plotted between Forward current (lf) on X-axis and the forward voltage
(Vf) on Y-axis.
B) Load Regulation characteristics:
1. Connect the Circuit as per the Circuit Diagram on the bread board.
2. By changing the load Resistance, kept constant I/P Voltage at 5V, 10 V, 15 V as
per table given below. Take the readings of O/P Voltmeter (Vo=Vz).
3. Now by changing the I/P Voltage, kept constant load Resistance at 1K, 2K, 3K as
per table given below. Take the readings of O/P Voltmeter (Vo=Vz).
LOAD REGULATION LINE REGULATION
PRECAUTIONS:
1. The terminals of the zener diode should be properly identified

2. While determined the load regulation, load should not be immediately shorted.
3. Should be ensured that the applied voltages & currents do not exceed the ratings of
the diode.
RESULT:
40
VIVA QUESTIONS:
1. What type of temp coefficient does the zener diode have?

2. If the impurity concentration is increased, how the depletion width effected?
3. Does the dynamic impendence of a zener diode vary?
4. Explain briefly about avalanche and zener breakdowns?
5. Draw the zener equivalent circuit?
6. Differentiate between line regulation & load regulation?
7. In which region zener diode can be used as a regulator?
8. How the breakdown voltage of a particular diode can be controlled?
9. What type of temperature coefficient does the Avalanche breakdown has?
10. By what type of charge carriers the current flows in zener and avalanche breakdown
diodes?
11. Define zener break down
12. Applications of zener diode
13. Explain how zener diode as voltage regulator
14.
41
3. HALF -WAVE RECTIFIER WITH AND WITHOUT FILTER
AIM: To examine the input and output waveforms of half wave Rectifier and also
Calculate its load regulation and ripple factor.
1. With Filter
2. Without Filter
APPARATUS:
Digital Multimeter - 1No.

Transformer (6V-0-6V) - 1No.
Diode, 1N4007 - 1No.
Capacitor 100μf/470 μf - 1No.
Decade Resistance Box - 1No.
Breadboard
CRO and CRO probes
Connecting wires
THEORY:
In Half Wave Rectification, When AC supply is applied at the input, only Positive Half
Cycle appears across the load whereas, the negative Half Cycle is suppressed. How this
can be explained as follows:
During positive half-cycle of the input voltage, the diode D1 is in forward bias
and conducts through the load resistor RL. Hence the current produces an output voltage
across the load resistor RL, which has the same shape as the +ve half cycle of the input
voltage.
During the negative half-cycle of the input voltage, the diode is reverse biased and
there is no current through the circuit. i.e., the voltage across R L is zero. The net result is
that only the +ve half cycle of the input voltage appears across the load. The average
value of the half wave rectified o/p voltage is the value measured on dc voltmeter.
For practical circuits, transformer coupling is usually provided for two reasons.
1. The voltage can be stepped-up or stepped-down, as needed.
2. The ac source is electrically isolated from the rectifier. Thus preventing shock
hazards in the secondary circuit.
The efficiency of the Half Wave Rectifier is 40.6%
42
Theoretical calculations for Ripple factor:

Without Filter:
Vrms = Vm/2
Vm = 2Vrms
Vdc = Vm/П
Ripple factor r=√ (Vrms/ Vdc )2 -1 =1.21
With Filter:
Ripple factor, r = 1/ (2√3 f C R)
CIRCUIT DIAGRAM:
A) Half Wave Rectifier Without Filter:
B) Half Wave Rectifier With Filter
43
MODEL WAVEFORMS:
A WAVEFORMS:
PROCEDURE:

2. Connect the primary side of the transformer to ac mains and the secondary side to the
rectifier input.
3. By the multimeter, measure the ac input voltage of the rectifier and, ac and dc voltage
at the output of the rectifier.
4. Find the theoretical value of dc voltage by using the formula,
Vdc=Vm/П
Where, Vm=2Vrms, (Vrms=output ac voltage.)
5.The Ripple factor is calculated by using the formula
r = ac output voltage/dc output voltage.
44
WITHOUT FILTER:
REGULATION CHARACTERSTICS:
2. By increasing the value of the rheostat, the voltage across the load and current
flowing through the load are measured.
3. The reading is tabulated.
4. From the value of no-load voltages, the %regulation is calculated using the
formula,
%Regulation = [(VNL-VFL) /VFL]*100
45
PRECAUTIONS:
1. The primary and secondary side of the transformer should be carefully identified
2. The polarities of all the diodes should be carefully identified.
3. While determining the % regulation, first full load should be applied and then it
should be decremented in steps
RESULT:
VIVA QUESTIONS:
1. What is the PIV of Half wave rectifier?

2. What is the efficiency of half wave rectifier?
3. What is the rectifier?
4. What is the difference between the half wave rectifier and Full Wave Rectifier?
5. What is the o/p frequency of Bridge Rectifier?
6. What are the ripples?
7. What is the function of the filters?
8. What is TUF?
9. What is the average value of o/p voltage for HWR?
10. What is the peak factor?
46
4. FULL-WAVE RECTIFIER WITH AND WITHOUT

FILTER
AIM: To Examine the input and output waveforms of Full Wave Rectifier and also
calculate its load regulation and ripple factor.
1. With Filter
2. Without Filter
APPARATUS:
Digital multimetersMultimeter - 1No.
Transformer (6V-0-6V) - 1No.
Diode, 1N4007 - 2No.
Capacitor 100μf/470 μf - 1No.
Decade Resistance Box - 1No.
Breadboard
CRO and CRO probes
Connecting wires
THEORY:
The circuit of a center-tapped full wave rectifier uses two diodes D1&D2.
During positive half cycle of secondary voltage (input voltage), the diode D1 is forward
biased and D2 is reverse biased. So the diode D1 conducts and current flows through
load resistor RL.
During negative half cycle, diode D2 becomes forward biased and D1 reverse
biased. Now, D2 conducts and current flows through the load resistor RL in the same
direction. There is a continuous current flow through the load resistor RL, during both
the half cycles and will get unidirectional current as show in the model graph. The
difference between full wave and half wave rectification is that a full wave rectifier
allows unidirectional (one way) current to the load during the entire 360 degrees of the
input signal and half-wave rectifier allows this only during one half cycle (180 degree).
THEORITICAL CALCULATIONS:
Vrms = Vm/ √2
Vm = Vrms√2
Vdc = 2Vm/П
(i) Without filter:
Ripple factor, r = √ (Vrms/ Vdc )2 -1 = 0.812
(ii) With filter:
Ripple factor, r = 1/ (4√3 f C RL)
47
CIRCUIT DIAGRAM:
A) FULL WAVE RECTIFIER WITHOUT FILTER:
B) FULL WAVE RECTIFIER WITH FILTER:
48
MODEL WAVEFORMS:
A) WAVEFORMS:
49
WITHOUT FILTER:
PROCEDURE:

2. Connect the ac mains to the primary side of the transformer and the secondary
side to the rectifier.
3. Measure the ac voltage at the input side of the rectifier.
4. Measure both ac and dc voltages at the output side the rectifier.
5. Find the theoretical value of the dc voltage by using the formula Vdc = 2Vm/П
6. Connect the filter capacitor across the load resistor and measure the values of
Vac and Vdc at the output.
50
7. The theoretical values of Ripple factors with and without capacitor are
calculated.
8. From the values of Vac and Vdc practical values of Ripple factors are
calculated. The practical values are compared with theoretical values.
PRECAUTIONS:
1. The primary and secondary side of the transformer should be carefully identified.
2. The polarities of all the diodes should be carefully identified.
RESULT:
VIVA QUESTIONS:
1. Define regulation of the full wave rectifier?

2. Define peak inverse voltage (PIV)? And write its value for Full-wave rectifier?
3. If one of the diode is changed in its polarities what wave form would you get?
4. Does the process of rectification alter the frequency of the waveform?
5. What is ripple factor of the Full-wave rectifier?
6. What is the necessity of the transformer in the rectifier circuit?
7. What are the applications of a rectifier?
8. What is meant by ripple and define Ripple factor?
9. Explain how capacitor helps to improve the ripple factor?
10. Can a rectifier made in INDIA (V=230v, f=50Hz) be used in USA (V=110v,
f=60Hz)?
51
5. INPUT AND OUTPUT CHARACTERISTICS OF

TRANSISTOR CE CONFIGURATION
AIM:
1. To draw the input and output characteristics of transistor connected in

CE configuration
2. To find β of the given transistor and also its input and output Resistances
APPARATUS:
Transistor, BC107 -1No.
Regulated power supply (0-30V) -1No.
Voltmeter (0-20V) - 2No.
Ammeters (0-20mA) -1No.
Ammeters (0-200μA) -1No.
Resistor, 100Ω -1No
Resistor, 1KΩ -1No.
Bread board
Connecting wires
THEORY:
In common emitter configuration, input voltage is applied between base and emitter
terminals and output is taken across the collector and emitter terminals.Therefore the
emitter terminal is common to both input and output.
The input characteristics resemble that of a forward biased diode curve. This is
expected since the Base-Emitter junction of the transistor is forward biased. As
compared to CB arrangement IB increases less rapidly with VBE. Therefore input
resistance of CE circuit is higher than that of CB circuit.
The output characteristics are drawn between Ic and VCE at constant IB the
collector current varies with VCE up to few volts only. After this the collector current
becomes almost constant, and independent of VCE. The value of VCE up to which the
collector current changes with V CE is known as Knee voltage. The transistor always
operated in the region above Knee voltage, IC is always constant and is approximately
equal to IB. The current amplification factor of CE configuration is given by
β = ΔIC/ΔIB
Input Resistance, ri = ∆VBE /∆IB (μA) at Constant VCE
Output Résistance, ro = ∆VCE /∆IC at Constant IB (μA)
52
CIRCUIT DIAGRAM:
MODEL GRAPHS:
A) INPUT CHARACTERISTICS:
B) OUTPUT CHARACTERSITICS:
53
OBSERVATIONS:
VCE = 1V VCE = 2V VCE = 4V

VBB
VBE(V) IB(μA) VBE(V) IB(μA) VBE(V) IB(μA)
B) OUTPUT CHARACTERISTICS:
IB = 50 μA IB = 75 μA IB = 100 μA
S.NO
VCE(V) IC(mA) VCE(V) IC(mA) VCE(V) IC(mA)
PROCEDURE:
A) INPUT CHARECTERSTICS:
1. Connect the circuit as per the circuit diagram.

2. For plotting the input characteristics the output voltage VCE is kept constant at 1V
and for different values of VBB , note down the values of IB and VBE
3. Repeat the above step by keeping VCE at 2V and 4V and tabulate all the readings.
4. plot the graph between VBE and IB for constant VCE
54
B) OUTPUT CHARACTERSTICS:
1. Connect the circuit as per the circuit diagram

2. for plotting the output characteristics the input current IB is kept constant at
50μA and for different values of VCC note down the values of IC and VCE
3. Repeat the above step by keeping IB at 75 μA and 100 μA and tabulate the all the
readings
4. plot the graph between VCE and IC for constant IB
PRECAUTIONS:
1. The supply voltage should not exceed the rating of the transistor
2. Meters should be connected properly according to their polarities
RESULT:
VIVA QUESTIONS:
1. What is the range of β for the transistor?

2. What are the input and output impedances of CE configuration?
3. Identify various regions in the output characteristics?
4. What is the relation between α and β?
5. Define current gain in CE configuration?
6. Why CE configuration is preferred for amplification?
7. What is the phase relation between input and output?
8. Draw diagram of CE configuration for PNP transistor?
9. What is the power gain of CE configuration?
10. What are the applications of CE configuration?
55
6. h-PARAMETERS OF CE CONFIGURATION
AIM: To calculate the h-parameters of transistor in CE configuration.
APPRATUS:
Transistor BC107 - 1No.

Resistors 100 K Ώ 100 Ώ - 1No.Each
Ammeter (0-200µA) - 1No.
Ammeter(0-200mA -1No.
Voltmeter (0-20V) - 2Nos
Regulated Power Supply (0-30V) - 2Nos
Breadboard
THEORY:
The two sets of characteristics are necessary to describe the behaviour of the CE
configuration, in which one for input or base emitter circuit and other for the output or
collector emitter circuit. In input characteristics the emitter base junction forward biased
by a very small voltage VBB where as collector base junction reverse biased by a very
large voltage VCC. The input characteristics are a plot of input current I B Versuss the input
voltage VBE for a range of values of output voltage VCE . The following important points
can be observed from these characteristics curves.
1. Input resistance is high as IB increases less rapidly with VBE

2. The input resistance of the transistor is the ratio of change in base emitter voltage
ΔVBE to change in base current ΔIB at constant collector emitter voltage (VCE ) i.e...
Input resistance or input impedance hie = ΔVBE / ΔIB at VCE constant.
B) OUTPUT CHARACTERISTICS:
A set of output characteristics or collector characteristics are a plot of out put current I C
VS output voltage VCE for a range of values of input current IB .The following important
points can be observed from these characteristics curves.
1. The transistor always operates in the active region. i.e. the collector current IC
increases with VCE very slowly. For low values of the VCE the IC increases rapidly with
a small increase in VCE .The transistor is said to be working in saturation region.
56
2. Output resistance is the ratio of change of collector emitter voltage ΔVCE , to change
in collector current ΔIC with constant IB. Output resistance or Output impedance hoe =
ΔVCE / ΔIC at IB constant.
Input Impedance hie = ΔVBE / ΔIB at VCE constant
Output impedance hoe = ΔVCE / ΔIC at IB constant
Reverse Transfer Voltage Gain hre = ΔVBE / ΔVCE at IB constant
Forward Transfer Current Gain hfe = ΔIC / ΔIB at constant VCE
CIRCUIT DIAGRAM:
MODEL GRAPH:
A) INPUT CHARACTERSITICS: i) calculation of hie ii) calculation of hre
57
OUPUT CHARACTERISITCS: i) calculation of hfe
ii) calculation of hoe
TABULAR FORMS:
A) Input Characteristics:
VCE=0V VCE=6V
S.NO
VBE(V) IB(μA) VBE(V) IB(μA)
58
B) Output Characteristics:
IB = 20 µA IB = 40 µA IB = 60 µA
S.NO VCE VCE VCE
IC(mA) IC(mA) IC(mA)
(V) (V) (V)
PROCEDURE:
1. Connect a transistor in CE configuration circuit for plotting its input and output
characteristics.
2. Take a set of readings for the variations in IB with VBE at different fixed values of
output voltage VCE .
3. Plot the input characteristics of CE configuration from the above readings.
4. From the graph calculate the input resistance hie and reverse transfer ratio hre by
taking the slopes of the curves.
5. Take the family of readings for the variations of IC with VCE at different values of
fixed IB.
6. Plot the output Characteristics from the above readings.
7. From the graphs calculate hfe and hoe by taking the slope of the curves.
RESULT:
VIVA QUESTIONS:
1. What are the h-parameters?

2. What are the limitations of h-parameters?
3. What are its applications?
4. Draw the Equivalent circuit diagram of H parameters?
5. Define H parameter?
6. What are tabular forms of H parameters monoculture of a transistor?
7. What is the general formula for input impedance?
8. What is the general formula for Current Gain?
9. What is the general formula for Voltage gain?
59
7.FREQUENCY RESPONSE OF CE AMPLIFIER
AIM:
1. To Measure the voltage gain of a CE amplifier
2. To draw the frequency response curve of the CE amplifier
APPARATUS:
Transistor BC107 -1No.
Regulated power Supply (0-30V) -1No.
Function Generator -1No.
CRO -1No.
Resistors [33KΩ, 3.3KΩ, 330Ω, -1No.Each
1.5KΩ, 1KΩ, 2.2KΩ, 4.7KΩ]
Capacitors, 10µF -2No
100µF -1No.
Bread Board
Connecting Wires
THEORY:
The CE amplifier provides high gain & wide frequency response. The emitter lead
is common to both input & output circuits and is grounded. The emitter-base circuit is
forward biased. The collector current is controlled by the base current rather than
emitter current. When a transistor is biased in active region it acts like an amplifier. The
input signal is applied to base terminal of the transistor and amplifier output is taken
across collector terminal. A very small change in base current produces a much larger
change in collector current. When positive half-cycle is fed to the input circuit, it
opposes the forward bias of the circuit which causes the collector current to decrease; it
decreases the voltage more negative. Thus when input cycle varies through a negative
half-cycle, increases the forward bias of the circuit, which causes the collector current
to increases thus the output signal is common emitter amplifier is in out of phase with
the input signal. An amplified output signal is obtained when this fluctuating collector
current flows through a collector resistor Rc.
The capacitor across the collector resistor Rc will act as a bypass capacitor. This
will improve high frequency response of amplifier.
60
CIRCUIT DIAGRAM:
MODELWAVE FORMS:
A) INPUT WAVE FORM:
61
B) OUTPUT WAVE FORM:
FREQUENCY RESPONSE:
OBSERVATIONS:
FREQUENCY RESPONSE: Vi = 20mv
Frequency in KHZ OUTPUT GAIN IN

VOLTAGE(Vo) dB=20log10(vo/vi)
62
PROCEDURE:
1. Connect the circuit as shown in circuit diagram
2. Apply the input of 20mV peak-to-peak and 1 KHz frequency using Function
Generator
3. The voltage gain can be calculated by using the expression , Av= (V0/Vi)
4. For plotting the frequency response the input voltage is kept Constant at 20mV
peak-to-peak and the frequency is varied from 100Hz to 1MHz Using function
generator
5. Note down the value of output voltage for each frequency.
6. All the readings are tabulated and voltage gain in dB is calculated by Using The
expression Av=20 log10 (V0/Vi)
7. A graph is drawn by taking frequency on x-axis and gain in dB on y-axis On Semi-
log graph.
10. The band width of the amplifier is calculated from the graph using the expression,
Bandwidth, BW = f2-f1
Where f1 lower cut-off frequency of CE amplifier, and

Where f2 upper cut-off frequency of CE amplifier
11. The bandwidth product of the amplifier is calculated using the Expression
Gain Bandwidth product = 3-dBmidband gain X Bandwidth
RESULT:
VIVA QUESTIONS:
1. What is phase difference between input and output waveforms of CE amplifier?

2. What type of biasing is used in the given circuit?
3. If the given transistor is replaced by a p-n-p, can we get output or not?
4. What is effect of emitter-bypass capacitor on frequency response?
5. What is the effect of coupling capacitor?
6. What is region of the transistor so that it is operated as an amplifier?
7. How does transistor acts as an amplifier?
8. Draw the h-parameter model of CE amplifier?
9. What type of transistor configuration is used in intermediate stages of a multistage
amplifier?
10. What is early effect?
63
8. CURRENT SHUNT FEEDBACK AMPLIFIER

AIM:
To determine the effect of feedback on the frequency response of a current shunt feedback amplifier.
EQUIPMENT REQUIRED: Hartley Oscillator kit, CRO, Connecting probes.

CIRCUIT DIAGRAM:
PROCEDURE:
TO DETERMINE THE FREQUENCY RESPONSE WITH FEEDBACK
OBSERVATIONS TABLE
1. WITHOUT FEEDBACK
Vi= 40mvp-p at 1kHz
S.No Frequency(hz) Output voltage(vo) Voltage gain Gain (db)

(vo/vi) Avf=20 log (vo/vi).
64
Bandwidth without feedback=------------
2. WITH FEEDBACK
Vi= 40mvp-p at 1kHz
S.NO Frequency(hz) Output voltage Voltage gain (avf=vo/vi) Gain (db)

(vo) Avf=20 log
(vo/vi).
Bandwidth with feedback = ------------
EXPECTED GRAPH:
65
RESULT:
The Av of the current shunt feedback amplifier is ___ and the bandwidth is ______ without feedback
and The Av of the current shunt feedback amplifier is ___ and the bandwidth is ______ with feedback.
QUESTIONS:
1. What is feedback?
2. What are the characteristics of feedback?
3. What is meant by sampling and mixing?
4. What are the configurations of feedback amplifiers?
5. What is the effect of feedback on an amplifier?
6. What is the effect of feedback on input and output resistances?
Exercise Question:
1. Determine the input resistance ,Output resistance of Current Shut Feedback amplifier with and
without feedback?
9. RC PHASESHIFT OSCILLATOR
AIM:
To determine the frequency of oscillation of an RC Phase Shift Oscillator.
EQUIPMENT REQUIRED: RC Phase shift oscillator kit, CRO, Connecting probes.
DESIGN PROCEDURE:
a) Let R = 10K
66
CIRCUIT DIAGRAM:
XSC1
VCC
Ext T rig
12V +
_
A B
+ _ + _
VCC R3
3.3kΩ
1 C2
R1 4
33kΩ
10µF
2 U1
C4 C6 C5 C1
6 7 8
1nF 1nF 1nF 10µF

BC107BP
R2 3
R5 R6 4.7kΩ
R7 10kΩ 10kΩ
10kΩ R4 C3
470Ω 100µF
0
PROCEDURE:
2. Connect the output of the RC Phase shift Oscillator kit to the CRO.
3. Observe the sinusoidal signal as an output and note down the time period of the oscillation.
4. Compare the practical frequency with the theoretical frequency.
EXPECTED WAVEFORM:
67
RESULT: The frequency of oscillation of the RC Phase Shift Oscillator is_____Hz.
QUESTIONS:
1. What is an Oscillator circuit?
2. What is the main difference between an amplifier and an oscillator?
3. State Barkhausen criterion for oscillation.
4. State the factors on which oscillators can be classified.
5. Give the expression for the frequency of oscillation and the minimum gain required for
sustained oscillations of the RC phase shift oscillator.
6. Why three RC networks are needed for a phase shift oscillator? Can it be two or four?
7. What are the merits and demerits of phase shift oscillator?
8. At low frequency which oscillators are found to be more suitable?
9. What are the two important RC oscillators?
Exercise Question:
1.Find the frequency of oscillations by changing the feedback circuit component values shown below.
68
Theoretical
frequency(KH Practical
S.No R( kΩ) C(µF) z) frequency(KHz)
1 10 0.01
2 10 0.022
3 10 0.033
10a. HARTLEY OSCILLATOR

AIM:
To determine the frequency of oscillations of the Hartley oscillator
EQUIPMENT REQUIRED: Hartley Oscillator kit, CRO, Connecting probes.
CIRCUIT DIAGRAM:
69
VCC
12V
VCC XFC1
R3
3.3kΩ 123
1 C2
R1 4
33kΩ
10µF
2 U1
C1
10µF
BC107BP
3
R2
4.7kΩ C3
R4 100µF
470Ω
L1 L2
5 100mH 100mH
C4
10µF
THEORY:
The Hartley oscillator is distinguished by a tank circuit consisting of two series-connected coils in
parallel with a capacitor, with the feedback signal needed for oscillation taken from the center
connection between the coils; the coils act as a voltage divider. The Hartley oscillator is the dual of the
Colpitts oscillator which uses a voltage divider made of two capacitors rather than two inductors.
Although there is no requirement for there to be mutual coupling between the two coil segments, the
circuit is usually implemented using a tapped coil, with the feedback taken from the tap, as shown
here. The optimal tapping point (or ratio of coil inductances) depends on the amplifying device used,
which may be a bipolar junction transistor, FET, triode, or amplifier of almost any type (non-inverting
in this case, although variations of the circuit with an earthed centre-point and feedback from an
inverting amplifier or the collector/drain of a transistor are also common), but a Junction FET (shown)
or triode is often employed as a good degree of amplitude stability (and thus distortion reduction) can
be achieved with a simple grid leak resistor-capacitor combination in series with the gate or grid (see
the Scott circuit below) thanks to diode conduction on signal peaks building up enough negative bias
to limit amplification. The frequency of oscillation is approximately the resonant frequency of the tank
circuit. If the capacitance of the tank capacitor is C and the total inductance of the tapped coil is L then
If two uncoupled coils of inductance L1 and L2 are used then
However if the two coils are magnetically coupled the total inductance will be greater because of
mutual inductance
The actual oscillation frequency will be slightly lower than given above, because of parasitic
70
capacitance in the coil and loading by the transistor.
Advantages of the Hartley oscillator include:
1. The frequency may be adjusted using a single variable capacitor, one side of which can be
earthed
2. The output amplitude remains constant over the frequency range
3. Either a tapped coil or two fixed inductors are needed, and very few other components
4. Easy to create an accurate fixed-frequency Crystal oscillator variation by replacing the
capacitor with a (parallel-resonant) quartz crystal or replacing the top half of the tank
circuit with a crystal and grid-leak resistor (as in the Tri-set oscillator).
Disadvantages include:
Harmonic-rich output if taken from the amplifier and not directly from the LC circuit (unless
amplitude -stabilization circuitry is employed).
PROCEDURE:
6. Connect the output of the Hartley Oscillator kit to the CRO.
EXPECTED GRAPH:
OBSERVATIONS:
i. Theoretical frequency of oscillation:
L1= L2= C=
ii. Practical frequency of oscillation:

T= _____
fo=1/ T= ___________Hz
RESULT:
The theoretical and practical frequency of oscillation of the Hartley Oscillator is calculated as
_________ and ___________.
Exercise Question:
71
Find the frequency of oscillations by changing the feedback circuit component values shown below.
Theoretical
frequency(KH Practical
S.No L1 mH L2 mH C1(µF) z) frequency(KHz)
1 5 5 0.01
2 5 5 0.022
3 5 5 0.033
10b. COLPITTS OSCILLATOR

AIM:
To determine the frequency of oscillation of a Colpitts Oscillator
EQUIPMENT REQUIRED: Colpitts Oscillator kit, CRO, Connecting probes
CIRCUIT DIAGRAM:
72
VCC
12V
XSC1
Ext T rig
VCC R3 +
_
3.3kΩ A B
+ _ + _
1 C2
R1 4
33kΩ
10µF XFC1
2 U1 123
C1
10µF
BC107BP
3
R2
4.7kΩ C3
R4 100µF
470Ω
C5 C6
5
10µF 10µF
L1
100mH
THEORY:
The Colpitts circuit, like other LC oscillators, consists of a gain device (such as a bipolar junction
transistor, field effect transistor, operational amplifier, or vacuum tube) with its output connected to its
input in a feedback loop containing a parallel LC circuit (tuned circuit) which functions as a bandpass
filter to set the frequency of oscillation. Colpitts oscillator is the electrical dual of a Hartley oscillator,
where the feedback signal is taken from an "inductive" voltage divider consisting of two coils in series
(or a tapped coil). Fig. 1 shows the common-base Colpitts circuit. L and the series combination of C1
and C2 form the parallel resonant tank circuit which determines the frequency of the oscillator. The
voltage across C2 is applied to the base-emitter junction of the transistor, as feedback to create
oscillations. Here the voltage across C1 provides feedback. The frequency of oscillation is
approximately the resonant frequency of the LC circuit, which is the series combination of the two
capacitors in parallel with the inductor.
The actual frequency of oscillation will be slightly lower due to junction capacitances and resistive
loading of the transistor.
As with any oscillator, the amplification of the active component should be marginally larger than the
attenuation of the capacitive voltage divider, to obtain stable operation. Thus, a Colpitts oscillator used
as a variable frequency oscillator (VFO) performs best when a variable inductance is used for tuning,
as opposed to tuning one of the two capacitors. If tuning by variable capacitor is needed, it should be
done via a third capacitor connected in parallel to the inductor (or in series as in the Clapp oscillator).
PROCEDURE:
73
2. Connect the output of the Colpitts Oscillator kit to the CRO.
EXPECTED GRAPH:
OBSERVATIONS:
I. THEORETICAL FREQUENCY OF OSCILLATION:
C1= C2= L=
II. PRACTICAL FREQUENCY OF OSCILLATION:
T= _____
fo =1/ T= ___________Hz
RESULT:
The theoretical and practical frequency of oscillation of the Colpitts Oscillator is calculated as
_________ and ___________.
QUESTIONS:
1. What is an Oscillator?
2. What is the main difference between an amplifier and an oscillator?
3. State Barkhausen criterion for oscillation.
4. State the factors on which oscillators can be classified.
5. What are the factors which contribute to change in frequency in oscillators?
Exercise Question:
Find the frequency of oscillations by changing the feedback circuit component values shown below.
C2(µF Practical
S.No L (mH) C1(µF) ) Theoretical frequency(KHz)
frequency(KH
74
z)
1 5 0.01 0.01
2 5 0.01 0.022
3 5 0.01 0.033
11. FREQUENCY RESPONSE OF COMMON SOURCE FET

AMPLIFIER
AIM:
75
1. To obtain the frequency response of the common source FET
Amplifier
2. To find the Bandwidth.
APPRATUS:
N-channel FET (BFW11) -1No.

Resistors (6.8KΩ, 1MΩ, 1.5KΩ) -1No.Each
Capacitors 0.1µF, -2Nos
47µF -1No.
Regulated power Supply (0-30V) -1No.
Function generator -1No.
CRO -1No.
CRO probes -1pair
Bread board
Connecting wires
THEORY:
A field-effect transistor (FET) is a type of transistor commonly used for weak-signal
amplification (for example, for amplifying wireless (signals). The device can amplify
analog or digital signals. It can also switch DC or function as an oscillator. In the FET,
current flows along a semiconductor path called the channel. At one end of the channel,
there is an electrode called the source. At the other end of the channel, there is an
electrode called the drain. The physical diameter of the channel is fixed, but its effective
electrical diameter can be varied by the application of a voltage to a control electrode
called the gate. Field-effect transistors exist in two major classifications. These are
known as the junction FET (JFET) and the metal-oxide- semiconductor FET
(MOSFET). The junction FET has a channel consisting of N-type semiconductor (N-
channel) or P-type semiconductor (P-channel) material; the gate is made of the opposite
semiconductor type. In P-type material, electric charges are carried mainly in the form
of electron deficiencies called holes. In N-type material, the charge carriers are
primarily electrons. In a JFET, the junction is the boundary between the channel and the
gate. Normally, this P-N junction is reverse-biased (a DC voltage is applied to it) so that
no current flows between the channel and the gate. However, under some conditions
there is a small current through the junction during part of the input signal cycle. The
FET has some advantages and some disadvantages relative to the bipolar transistor.
Field-effect transistors are preferred for weak-signal work, for example in wireless,
communications and broadcast receivers. They are also preferred in circuits and systems
76
requiring high impedance. The FET is not, in general, used for high-power
amplification, such as is required in large wireless communications and broadcast
transmitters.
Field-effect transistors are fabricated onto silicon integrated circuit (IC) chips. A
single IC can contain many thousands of FETs, along with other components such as
resistors, capacitors, and diodes.
A common source amplifier FET amplifier has high input impedance and a
moderate voltage gain. Also, the input and output voltages are 180 degrees out of Phase.
CIRCUIT DIAGRAM:
MODEL GRAPH:
A) INPUT WAVEFORM
77
B) OUTPUT WAVEFORM
FREQUENCY RESPONSE PLOT:
OBSERVATIONS:
INPUT VOLTAGE (Vi) =20mA
S.NO Output Voltage(Vo) Voltage Gain in

gain=V0/Vin dB=20log10(V0/Vin)
PROCEDURE:
2. A signal of 1 KHz frequency and 20mV peak-to-peak is applied at
the Input of amplifier.
3. Output is taken at drain and gain is calculated by using the expression,
Av=V0/Vi
4. Voltage gain in dB is calculated by using the expression,
Av=20log 10(V0/Vi)
5. Repeat the above steps for various input voltages.
6. Plot Av in dB Versus Frequency
7. The Bandwidth of the amplifier is calculated from the graph using
the Expression,
Bandwidth BW=f2-f1
Where f1 is lower 3 dB
frequency f2 is upper 3 dB
frequency
PRECAUTIONS:
1. All the connections should be tight.
2. Transistor terminals must be identified properly
RESULT:
VIVA QUESTIONS:
1. What is the difference between FET and BJT?
2. FET is unipolar or bipolar?
3. Draw the symbol of FET?
4. What are the applications of FET?
5. FET is voltage controlled or current controlled?
6. Draw the equivalent circuit of common source FET amplifier?
7. What is the voltage gain of the FET amplifier?
8. What is the input impedance of FET amplifier?
9. What is the output impedance of FET amplifier?
10. What are the FET parameters?
11. What are the FET applications
11: Uni-junction transistor (UJT)
CHARACTERISTICS
AIM: To observe the characteristics of UJT and to calculate the Intrinsic Stand-OffRatio (η).
APPARATUS: Regulated Power Supply (2Nos) (0-30V, 1A) , UJT 2N2646,Resistors10kΩ,

47Ω, 330Ω, Multimeters ,Breadboard and Connecting Wires
T
A Unijunction Transistor
H (UJT) is an electronic semiconductor device
E
O
R
Y
:
That has only one junction. It has three terminals an emitter (E) and two bases (B1 and B2). The
base is formed by lightly doped n-type bar of silicon. Two ohmic contacts B1 and B2 are
attached at its ends. The emitter is of p-type and it is heavily doped. The resistance between B1
and B2, when the emitter is open- circuit is called interbase resistance. The original UJT, is a
simple device that is essentially a bar of N type semiconductor material into which P type
material has been diffused somewhere along its length.
The UJT is biased with a positive voltage between the two bases. This causes a potential drop
along the length of the device. When the emitter voltage is driven approximately one diode
voltage above the voltage at the point where the P diffusion (emitter) is, current will begin to
flow from the emitter into the base region. Because the base region is very lightly doped, the
additional current (actually charges in the base region) causes (conductivity modulation) which
reduces the resistance of the portion of the base between the emitter junction and the B2
terminal. This reduction in resistance means that the emitter junction is more forward biased, and
so even more current is injected. Overall, the effect isa negative resistance at the emitter terminal.
This is what makes the UJT useful, especially in simple oscillator circuits. Whenthe emitter
voltage reaches Vp, the current starts to increase and the emitter voltage starts to decrease. This is
represented by negative slope of the characteristics which is referred to as the negative resistance
region, beyond the valley point , VEB proportional to IE.
PROCEDURE:
1. Connection is made as per circuit diagram.
2. Output voltage is fixed at a constant level and by varying input voltage
corresponding emitter current values are noted down.
3. This procedure is repeated for different values of output voltages.
4. All the readings are tabulated and Intrinsic Stand-Off ratio is calculated using
η = (Vp-VD) / VB2B1
5. A graph is plotted between VE and IE for different values of VB2B1.
OBSEVATIONS:
VB2B1=2V VB2B1=3V
VEB(V) IE(mA) VEB(V) IE(mA)
CALCULATIONS
VP = ηVB2B1 + VD
η = (VP-VD) / VB2B1
η = ( η1 + η2 ) / 2
APPLICATION: UJT can be used as trigger device for SCR’s. traics and otherapplications
including saw tooth generator , phase control and timing circuits.
Viva questions:
1. What is a pn junction? How is it formed? (2M)

2. Sketch the energy-band Diagrams for intrinsic and extrinsic semiconductors (3M)
3. What is meant by rectifier? (2M)
4. Compare the performance measure of different filters. (3M)
5. Why Transistor is called Current Controlled Device? (2M)
6. What is early effect? How does it modify the V-I characteristics of a BJT? (3M)
7. What is meant by operating point? Explain its significance (2M)
8. What is the condition for thermal stability and thermal resistance? (3M)
9. Explain when a FET acts as a voltage variable resistor. (2M)
10. Explain the drain and transfer characteristics of a JFET in details (3M)
11. What do you mean by potential barrier for a p-n junction? (2M)
12. What is the significance of negative resistance of a tunnel diode (3M)
13. Define peak inverse voltage (PIV). (2M)
14. Explain FWR working principle with circuit and waveforms. (3M)
15. What are the three regions of a Transistor? (2M)
16. What is thermal runway? How can it avoid? (3M)
17. What is faithful amplification? (2M)
18. Derive relation between α, β and γ? (3M)
19. Define the pinch off voltage (Vp) sketch the depletion region before and after
Pinch-off? (2M)
20. Derive Expression for saturation drain current (3M)
21. What is mean by zener breakdown (2M)
22. Explain the effect of temperature on the V-I characteristics of pn junction diode
(3M)
23. What is meant by filter in rectifier circuits (2M)
24. Bridge rectifier is becoming more and more popular, why? (3M)
25. Write B.J.T specifications and limitations (2M)
26. Explain how transistor acts as an Amplifier? (3M)
27. What is meant by stabilization (2M)
28. What is thermal runway? How can it avoid? (3M)
29. State the application of JFET and compare MOSFET (2M)
30. When FET acts as a voltage variable resistor ( V.V.R)? (3M)
31. What is diode equation? (2M)
32. Draw the V-I characteristics of SCR & define all related terms. (3M)
33. What is the purpose of bleeder resistance in a rectifier circuit using LC filter?
(2M)
34. Write short note on Full wave rectifier (FWR) along with input output
waveforms. (3M)
35. Why hybrid parameters are called so? Define those (2M)
36. What factors are to be considered for selecting the operating point Q for an
amplifier? (3M)
37. Why does potential divider method of biasing become universal? (2M)
38. Why FET is unipolar and BJT is Bipolar Device (3M)
39. Draw the symbols of JFET ( N Channel/P channel ) MOSFET (Depletion

MOSFET
(n-channel/p-channel) and Enhancement MOSFET (n-channel/p-channel)
(2M)
40. Draw the low frequency hybrid equivalent circuit for CE,CB and CC (3M)
41. Sketch the V-I characteristics of p-n junction diode for forward bias? (2M)
42. Explain zener diode as a voltage regulator. (3M)
43. Distinguish between the incremental resistance and the apparent resistance of
the diode (2M)
44. Derive efficiency of FWR. (3M)
45. In a filter circuit, why capacitor is a parallel combination and series combination
for inductor. (2M)
46. Define Transformer Utilization Factor (TUF). (2M)
47. What is transistor? (3M)
48. Draw voltage divider bias circuit; derive an expression for its stability factor.(2M)
49. Explain transfer characteristics of JFET with its non-linear relations (3M)
50. Explain tunneling effect (2M)

Electronic Devices and Circuits Lab

Uploaded by

Copyright:

Available Formats

Electronic Devices and Circuits Lab

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Electronic Devices and Circuits Lab

Uploaded by

Copyright:

Available Formats

ELECTRONIC DEVICES AND CIRCUITS

Department of Electronics and Communication Engineering

MALLA REDDY COLLEGE

PROGRAMME EDUCATIONAL OBJECTIVES

PEO2: TECHNICAL ACCOMPLISHMENTS

PEO3: INVENTION, INNOVATION AND CREATIVITY

PEO4: PROFESSIONAL DEVELOPMENT

PEO5: HUMAN RESOURCE DEVELOPMENT

CODE OF CONDUCT FOR THE LABORATORIES

Before leaving the lab

BASIC REQUIREMENT FOR EDC LAB

1) Identification, Specifications, Testing of R, L, C Components (Color Codes), Potentiometers,

JFET’s, MOSFET’s, Power Transistors, LED’s, LCD’s, UJT.

3) Study and operation of

a) Multi meters (Analog and Digital)

c) Regulated Power Supplies

PART B: (For Laboratory Examination – Minimum of 10 experiments)

1) P-N junction diode forward and reverse bias characteristics. 33

2) Zener diode characteristics and Zener as voltage regulator. 37

3) Half –Wave Rectifier without and with capacitor filter. 42

4) Full – Wave Rectifier without and with capacitor filter. 47

5) Input and output characteristics of a BJT in CE configuration. 52

6) Measurement of h – parameters in CE configuration. 56

7) Frequency response of CE amplifier. 60

8) Feedback amplifiers: Voltage series and current shunt 64

9) RC phase shift oscillator using transistors. 67

10) Hartley & Colpitts oscillator using transistors. 70

11) Frequency response of common source JFET amplifier. 76

12) UJT Characteristics. 80

1. BASIC ELECTRONIC COMPONENTS

Table1: Colour codes of resistor

Table2: Procedure to find the value of resistor using colour codes

COLOUR CODING OF CAPACITORS

An electrical device capable of storing electrical energy. In general, a capacitor consists

 Capacitor Identification Codes: There are no international agreements in place to

Figure 1: Plastic Film Types

Figure 2: Picofarads Representation

Figure3: Ceramic Disk Capacitor

Figure 4 shows some other miscellaneous schemes.

Figure 4: Miscellaneous Schemes.

 Electrolytic capacitor properties

 Leakage: Although electrolytic capacitors have much higher levels of capacitance

The physical appearance of electrolytic capacitor is as shown in Figure 5.The capacitors

Figure 5: Electrolytic Capacitor

It is absolutely necessary to ensure that any electrolytic capacitors are connected

COLOUR CODING OF INDUCTORS

Figure 6: Typical inductors colour coding and their values.

WIRES AND CONNECTIONS

S.NO COMPONENT CIRCUIT SYMBOL FUNCTION

A 'blob' should be drawn

S.NO COMPONENT CIRCUIT SYMBOL FUNCTION

Supplies electrical energy.

S.NO COMPONENT CIRCUIT SYMBOL FUNCTION

A transducer which converts

5 BELL A transducer which converts

6 BUZZER A transducer which converts

A coil of wire which creates

S.NO COMPONENT CIRCUIT SYMBOL FUNCTION

DPST = Double Pole, Single

DPDT = Double Pole,