Technical Habilis 8
Technical Habilis 8
Technical Habilis 8
2. The sum of the voltage drop around a circuit is equal to the source voltage is ___________.
a. Kirchhoff’s law b. Ohm’s law c. Nevin’s Theory d. Faraday’s Law
9. If a 120V incandescent light bulb is operating at a voltage of 125V, the result will be _________.
a. it may be enough to blow a fuse
b. the bulb won’t be as bright
c. shorter life of the bulb
d. the wattage would be less than rated
11. The code requires which of the following colors for the equipment grounding conductor?
a. white or gray b. green or green with yellow stripes c. yellow d. blue with yellow stirpes
12. Sometimes mercury toggle switches are used in place of a regular toggle switch because they _________.
a. are easier to connect b. do not wear out as quickly
c. are less expensive d. they glow in the dark
13. The assigned color for the high-leg conductor of a three phase, 4 –wire delta secondary is __________.
a. red b. black c. blue d. orange
14. The Code rule for maximum 900 bends in a conduit between two boxes is four, the most likely reason for the total 360 degree limitation
is ___________.
a. it is unsafe
b. it makes pulling the conductors through the conduit too difficult
c. you can damage the galvanized coating on the conduit
d. too many bends require extra wire to be pulled
15. The correct word to define wiring which is not concealed is ________.
a. open b. uncovered c. exposed d. bare
16. The property of a circuit tending to pre vent the flow of current and a the same time causing energy to be converted into heat is referred to as______
a. the inductance b. the resistance c. the capacitance d. the reluctance
20. In a resistance the wall switch controlling the ceiling light is usally________.
a. connected across both lines b. a double pole switch
c. connected in one line only d. a 4-way switch
21. A switch w/c opens automatically when the circuits exceeds a predetermined limit would be called_______.
a. limit switch b. circuit breaker c. DT disconnect d. contactor
23. The Philippine Electrical Code rules that apply to electric welders are covered in article ________.
a. 520 b. 600 c. 620 d. 630
24. Acid is NOT considered a good flux when soldering conductors because it _______.
a. smells bad b. is corrosive c. is non-corrosive d. costs too much
25. If the spring tension on a cartridge fuse clip is weak, the result most likely would be _________.
a. the fuse would blow immediately b. the fuse clips would become warm
c. the voltage to the load would increase d. the supply voltage would increase
26. The branch-circuit loads specified by the Code for lighting and receptacle are considered ________.
a. minimum load b. maximum loads c. loads to be served d. peak loads
28. After cutting a conduit, to remove the rough edges on both ends, the conduit ends should be ________.
a. reamed b. filed c. sanded d. ground
29. To fasten a raceway to solid concrete ceiling, you would use __________.
a. toggle bolts b. expansion bolts c. wooden pluds d. rawl plugs
33. The difference of electrical potential between two conductors of a circuit is the:
a. resistance b. amperage c. voltage d. wattage
38. When cutting a metal conduit with a hacksaw, the pressure applied to the hacksaw should be on_______.
a. the return stroke only b. the forward stroke only
c. both the forward and return stroke only d. none of these
39. The switches to be closed in order to obtain a combined resistance of 5Ω are________
a. 1 and 4 b. 2 and 3
c. 1 and 2 d. 1 and 3
40. When the term “10-32” in connection with machine screws commonly used in lighting work, the number 32 refers to ________.
a. ) screw length b. ) screw thickness c. ) diameter of hole d. ) threads per inch
43. The flux commonly used for the soldering of the electrical conductor is _________.
a. zinc chloride b. rosin c. borax d. none of these
44. A shunt is sometimes used to increase the range of an electrical measuring instrument. The shunt is normally used when measuring ____
a. AC voltage b. DC voltage c. DC amperes d. AC amperes
46. When and electric current is forced through a wire that has considerable resistance, the _________.
I. ampacity will decrease II. Voltage will drop III. Wire will heat up
a. III only b. I and II only c. II and III only d. I and III only
47. The continuity of an electrical circuit can be determined in the field by the means of ________.
a. an ammeter b. Wheatstone bridge
c. bell & battery set d. watt-meter
50. Which of the following is the symbol for a duplex outlet, split current?
a. b. c. d.
TECHNICAL_REF_008_02
2. The sum of the voltage drop around a circuit is equal to the source voltage is ___________.
a. Kirchhoff’s law b. Ohm’s law c. Nevin’s Theory d. Faraday’s Law
9. If a 120V incandescent light bulb is operating at a voltage of 125V, the result will be _________.
a. it may be enough to blow a fuse
b. the bulb won’t be as bright
c. shorter life of the bulb
d. the wattage would be less than rated
11. The code requires which of the following colors for the equipment grounding conductor?
a. white or gray b. green or green with yellow stripes c. yellow d. blue with yellow stirpes
12. Sometimes mercury toggle switches are used in place of a regular toggle switch because they _________.
a. are easier to connect b. do not wear out as quickly
c. are less expensive d. they glow in the dark
13. The assigned color for the high-leg conductor of a three phase, 4 –wire delta secondary is __________.
a. red b. black c. blue d. orange
14. The Code rule for maximum 900 bends in a conduit between two boxes is four, the most likely reason for the total 360
degree limitation is ___________.
a. it is unsafe
b. it makes pulling the conductors through the conduit too difficult
c. you can damage the galvanized coating on the conduit
d. too many bends require extra wire to be pulled
15. The correct word to define wiring which is not concealed is ________.
a. open b. uncovered c. exposed d. bare
16. The property of a circuit tending to pre vent the flow of current and a the same time causing energy to be converted into heat is referre
as________.
a. the inductance b. the resistance c. the capacitance d. the reluctance
20. In a resistance the wall switch controlling the ceiling light is usally________.
a. connected across both lines b. a double pole switch
c. connected in one line only d. a 4-way switch
21. A switch w/c opens automatically when the circuits exceeds a predetermined limit would be called_______.
a. limit switch b. circuit breaker c. DT disconnect d. contactor
23. The Philippine Electrical Code rules that apply to electric welders are covered in article ________.
a. 520 b. 600 c. 620 d. 630
24. Acid is NOT considered a good flux when soldering conductors because it _______.
a. smells bad b. is corrosive c. is non-corrosive d. costs too much
25. If the spring tension on a cartridge fuse clip is weak, the result most likely would be _________.
a. the fuse would blow immediately b. the fuse clips would become warm
c. the voltage to the load would increase d. the supply voltage would increase
26. The branch-circuit loads specified by the Code for lighting and receptacle are considered ________.
a. minimum load b. maximum loads c. loads to be served d. peak loads
28. After cutting a conduit, to remove the rough edges on both ends, the conduit ends should be ________.
a. reamed b. filed c. sanded d. ground
29. To fasten a raceway to solid concrete ceiling, you would use __________.
a. toggle bolts b. expansion bolts c. wooden pluds d. rawl plugs
33. The difference of electrical potential between two conductors of a circuit is the:
a. resistance b. amperage c. voltage d. wattage
38. When cutting a metal conduit with a hacksaw, the pressure applied to the hacksaw should be on_______.
a. the return stroke only b. the forward stroke only
c. both the forward and return stroke only d. none of these
39. The switches to be closed in order to obtain a combined resistance of 5Ω are________
a. 1 and 4 b. 2 and 3
c. 1 and 2 d. 1 and 3
40. When the term “10-32” in connection with machine screws commonly used in lighting work, the number 32 refers to ________.
a. ) screw length b. ) screw thickness c. ) diameter of hole d. ) threads per inch
43. The flux commonly used for the soldering of the electrical conductor is _________.
a. zinc chloride b. rosin c. borax d. none of these
44. A shunt is sometimes used to increase the range of an electrical measuring instrument. The shunt is normally used when measuring ____
a. AC voltage b. DC voltage c. DC amperes d. AC amperes
46. When and electric current is forced through a wire that has considerable resistance, the _________.
I. ampacity will decrease II. Voltage will drop III. Wire will heat up
a. III only b. I and II only c. II and III only d. I and III only
47. The continuity of an electrical circuit can be determined in the field by the means of ________.
a. an ammeter b. Wheatstone bridge
c. bell & battery set d. watt-meter
50. Which of the following is the symbol for a duplex outlet, split current?
a. b. c. d.