Pioneer CDJ-2000NXS2 Service Manual
Pioneer CDJ-2000NXS2 Service Manual
RRV4645
CDJ-2000NXS2
MULTI PLAYER
CDJ-2000NXS2
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Remarks
THIS SERVICE MANUAL SHOULD BE USED TOGETHER WITH THE FOLLOWING MANUAL(S).
Model Order No. Remarks
CDJ-2000NXS2 RRV4646 SCHEMATIC DIAGRAM, PCB CONNECTION DIAGRAM, PCB PARTS LIST
SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
B
This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive
harm.
Health & Safety Code Section 25249.6 - Proposition 65
IMPORTANT
Laser Pickup specifications and Laser characteristics
THIS PIONEER APPARATUS CONTAINS
LASER OF CLASS 1. For DVD Wave length (typ) : 655 nm
SERVICING OPERATION OF THE APPARATUS Operation output : 3 mW CW, Class 1
S H O U L D B E D O N E B Y A S P E C I A L LY Maximum output : Class 1 (Under fault condition)
INSTRUCTED PERSON. For CD Wave length (typ) : 790 nm
Operation output : 4.5 mW CW, Class 1
Maximum output : Class 1 (Under fault condition)
C
LABEL CHECK
Bottom view
2 CDJ-2000NXS2
1 2 3 4
5 6 7 8
CONTENTS
SAFETY INFORMATION.......................................................................................................................................................... 2
1. SERVICE PRECAUTIONS .................................................................................................................................................... 4
1.1 NOTES ON SOLDERING ............................................................................................................................................... 4 A
1.2 NOTES ON REPLACING PARTS ................................................................................................................................... 4
1.3 SERVICE NOTICE.......................................................................................................................................................... 5
2. SPECIFICATIONS................................................................................................................................................................. 7
3. BASIC ITEMS FOR SERVICE .............................................................................................................................................. 7
3.1 JIGS LIST ....................................................................................................................................................................... 7
3.2 CHECK POINTS AFTER SERVICING ........................................................................................................................... 8
3.3 PCB LOCATIONS ........................................................................................................................................................... 9
4. BLOCK DIAGRAM .............................................................................................................................................................. 10
4.1 OVERALL WIRING DIAGRAM ..................................................................................................................................... 10
4.2 SIGNAL BLOCK DIAGRAM.......................................................................................................................................... 11
4.3 POWER SUPPLY BLOCK DIAGRAM........................................................................................................................... 12
5. DIAGNOSIS ........................................................................................................................................................................ 13 B
5.1 SEQUENCE.................................................................................................................................................................. 13
5.2 FAILURE JUDGEMENT OF THE PICKUP ASSY ........................................................................................................ 15
5.3 TROUBLESHOOTING.................................................................................................................................................. 16
5.4 OPERATIONAL WAVEFORMS .................................................................................................................................... 30
5.5 CONNECTION CONFIRMATION WITH THE PC ......................................................................................................... 31
6. SERVICE MODE ................................................................................................................................................................. 32
6.1 SERVICE MODE .......................................................................................................................................................... 32
6.2 ABOUT THE DEVICE................................................................................................................................................... 47
7. DISASSEMBLY ................................................................................................................................................................... 48
8. EACH SETTING AND ADJUSTMENT ................................................................................................................................ 66
8.1 NECESSARY ITEMS TO BE NOTED........................................................................................................................... 66
C
8.2 FIRMWARE UPDATE / RECOVERY............................................................................................................................. 66
8.3 WRITING THE SERIAL NUMBER OF THE UNIT ........................................................................................................ 67
8.4 JOG DIAL ROTATION LOAD ADJUSTMENT ............................................................................................................... 68
8.5 TEMPO ZERO POINT ADJUSTMENT ......................................................................................................................... 69
8.6 ITEMS FOR WHICH USER SETTINGS ARE AVAILABLE........................................................................................... 70
9. EXPLODED VIEWS AND PARTS LIST............................................................................................................................... 71
9.1 PACKING SECTION ..................................................................................................................................................... 71
9.2 EXTERIOR SECTION .................................................................................................................................................. 73
9.3 CONTROL PANEL SECTION ....................................................................................................................................... 75
9.4 JOG DIAL SECTION .................................................................................................................................................... 77
9.5 DISPLAY SECTION ...................................................................................................................................................... 79
9.6 SLOT IN MECHA SECTION ......................................................................................................................................... 81 D
CDJ-2000NXS2 3
5 6 7 8
1 2 3 4
1. SERVICE PRECAUTIONS
1.1 NOTES ON SOLDERING
A • For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
Do NOT use a soldering iron whose tip temperature cannot be controlled.
4 CDJ-2000NXS2
1 2 3 4
5 6 7 8
For prevention of electrical shock, before starting working on the product, be sure to wait at least 2 minutes after unplugging
the Power cord.
About the Flash ROM (IC12) and USB-LAN Conversion IC (IC602) in the MAIN Assy
Replacement of the Flash ROM (IC12) and USB-LAN Conversion IC (IC602) in the MAIN Assy is not possible during service,
because writing of the MAC address on the production line is required and USB-LAN Conversion IC (IC602) has unique ID.
Therefore, the Flash ROM (IC12) and USB-LAN Conversion IC (IC602) are not supplied as a service part.
If the Flash ROM and USB-LAN Conversion IC are defective, replace the whole MAIN Assy.
After replacing the the MAIN Assy, writing of the serial number of the unit is required.
For details on how to write the serial number, see "8.3 WRITING THE SERIAL NUMBER OF THE UNIT."
About transfer of the accumulated LD lighting time data after replacement of the MAIN Assy
This unit is equipped with self-diagnostic functions for the drives in Service mode. The service-life check for the laser
diode (for CDs/DVDs) among the self-diagnostic functions uses the accumulated lighting time for judgment. If it is
7,000 hours or less, the laser diode is judged as OK. The accumulated lighting time of the LD is stored in the Flash ROM
(IC12) in the MAIN Assy. Therefore, after replacement of the MAIN Assy, the accumulated lighting time of the LD is cleared
and proper judgment will not be possible after that. To avoid such a situation, when replacement of the
MAIN Assy is required, transfer the LD accumulated lighting time data. D
Before replacement, confirm the drive LD lighting time in Service mode and take note of the time value. After replacement
is finished, enter Service mode then change the drive LD lighting time value to what you noted.
For details on how to confirm and change the LD lighting time, see "6 Drive LD life manual input" in "[3] Various displayed
information" in "6.1 SERVICE MODE."
CDJ-2000NXS2 5
5 6 7 8
1 2 3 4
When discharging the above point, use the following discharge jig as needed.
While the charging voltage is left of both C4 and C5, either of checking LEDs turns on.
And if both of LED turns off, we can avoid receiving the electrical shock!!
D Checking C4 C5
LEDs
E No
polarity
F
When there is no above type LED, take measures the following method.
Step 1: After the power is turned off, wait 2 minutes.
Step 2: Connect the Register Jig and leave the unit as it is, for 10 seconds.
6 CDJ-2000NXS2
1 2 3 4
5 6 7 8
2. SPECIFICATIONS
Analog audio output (AUDIO OUT L/R) • The specifications and design of this product are subject to
Output terminals ..........................................................RCA terminal change without notice.
Output Level .......................................................... 2.0 Vrms (1 kHz)
Frequency response..................................................4 Hz to 40 kHz
S/N ratio.................................................................................115 dB Accessories B
Total harmonic distortion ................................................... 0.0018 % • Power cord
(SYXJ: ADG1244)
Digital audio output (DIGITAL OUT) (UXJCB: DDG1108)
Output terminals ..........................................................RCA terminal (FLXJ: ADG1244, ADG1239)
Output type..................................................Coaxial digital (S/PDIF) (AXJ: DDG1114)
Output level...............................................................0.5 Vp-p (75 Ω)
Output format..................................... 44.1 kHz/96 kHz, 24 bit/16 bit • Audio cable
(XDE3045)
USB downstream section (USB)
Port ........................................................................................ Type A • LAN cable
Power supply.......................................................... 5 V/2.1 A or less (DDE1141)
USB upstream section (USB) • Disc force eject pin (mounted on bottom of product)
Port ........................................................................................ Type B C
(DEX1024)
Cleaning
Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools.
F
Position to be cleaned Name Part No. Remarks
Pickup lens Cleaning liquied GEM1004 Refer to "9.6 SLOTIN MECHA SECTION".
Cleaning paper GED-008
CDJ-2000NXS2 7
5 6 7 8
1 2 3 4
B Playback data contained in the device connected to USB A. Audio, Search and operations must be normal.
USB B. The PC must be linked.
Playback data contained in an SD card. Audio, Search and operations must be normal.
LINK. The PC must be linked.
5 Check output signals while the Jog dial or TEMPO slider is Audio and operations must be normal.
being operated.
6 Check the keys on the unit. Check whether a product can be operated properly by buttons
on the product.
7 Check the LCD display. Check that there is no dirt or dust trapped inside the LCD display.
8 Check the Touch panel. Check whether a product can be operated properly in an all-black
screen of the Service mode.
C
9 Check the appearance of the product. No scratches or dirt on its appearance after receiving it for service.
See the table below for the items to be checked regarding audio.
Item to be checked regarding audio
D
Distortion Volume too high
Noise Volume fluctuating
Volume too low Sound interrupted
8 CDJ-2000NXS2
1 2 3 4
5 6 7 8
A
H LCDB ASSY
E MAIN ASSY
F USBA ASSY
N EUPB ASSY
G SDCB ASSY
Q SW POWER
I PNLB ASSY SUPPLY ASSY
J HLED ASSY
B
K JFLB ASSY
L JOGB ASSY
M SLDB ASSY
O KSWD ASSY
• Bottom view
P INDB ASSY
C
TM ASSY 09SD-S D SLMB ASSY
C B
INSW SPCN
ASSY ASSY
A SRVB
ASSY
D
• Bottom view SLOTIN MECHA
G11 ASSY
• Bottom view
NOTES: - Parts marked by “NSP” are generally unavailable because they are not in our Master Spare Parts List.
- The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Mark No. Description Part No. Mark No. Description Part No.
LIST OF ASSEMBLIES
1..MAIN ASSY DWX3672 NSP 1..PNLA ASSY DWM2571 E
2..PNLB ASSY DWX3702
NSP 1..LCDA ASSY DWM2569 2..KSWB ASSY DWX3703
2..LCDB ASSY DWX3693 2..EUPB ASSY DWX3704
2..SDCB ASSY DWX3694 2..SLMB ASSY DWX3707
2..USBA ASSY DWX3695 2..JFLB ASSY DWX3708
2..JOGB ASSY DWX3709
NSP 1..SRVA ASSY DWM2570
2..SRVB ASSY DWX3696 1..SLDB ASSY DWX3705
2..INSW ASSY DWX3697
2..SPCN ASSY DWX3698 1..HLED ASSY DWX3700
2..INDB ASSY DWX3699
> 1..SW POWER SUPPLY ASSY DWR1548
F
NSP SLOTIN MECHA G11 ASSY DXA2163
TM ASSY 09SD-S DXX2697
CDJ-2000NXS2 9
5 6 7 8
F
*HORIZONTAL
TFT-LCD MODULE (CWX4352-) CN4401
CKS6625-A
CN4801
BackLight
CKS4428-A
1 YT
Anode 1
TOUCH PANEL (DSX1130-)
2 XR
CN4601
DKN1445-A
Cathode 2 3 YB NM
4 XL FOR DEBUG
1
1
1 V+3R3_CPU
*VERTICAL *VERTICAL 2 V+3R3_CPU USB CONNECTOR USB CONNECTOR
CN6301
VKN1418-A
CN4001
VKN1418-A
3 GNDD (A-TYPE) (B-TYPE)
4 GNDD
V+12 1 1 V+12 5 REST_ER
1
2 *HORIZONTAL RT2 RT1 SD CARD
V+12 2 V+12 6 CPU_TRST
CN4802
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
RT5
1
2
3
4
6
7
8
9
GNDD 3 GNDD
RT1
RT2
3 7 CPU_TDI
RT3 RT4
NC
GND
VGL
VCC
VGH
NC
V1
V2
V3
V4
V5
V6
V7
V8
V9
V10
NC
NC
DITH
VCOM
AVDD
AGND
GND
UPDN
VCC
SHLR
STBYB
RSTB
MODE
VSD
HSD
DE
DCLK
B7
B6
B5
B4
B3
B2
B1
B0
G7
G6
G5
G4
G3
G2
G1
G0
R7
R6
R5
R4
R3
R2
R1
R0
VCC
AVDD
AGND
4 CKS6646-A
GNDD 4 GNDD 8 CPU_TMS
ZIF
JA5101 JA502
4
SD_SW 5 5 SD_SW 9 CPU_TCK 12
G SDCB ASSY
DDD1711- DKN1664-A
4
DKB1118-A SD_W
SD_ILM_G 6 6 SD_ILM_G 10
FFC CPU_TDO
USBA ASSY
VBUS
D-
D+
GND
SD_ILM_R 7 (REVERSE FACE) 7 SD_ILM_R 11 CPU_MPMD 11
F
TER
SD_ILM_B 8 L=56mm 8 SD_ILM_B 12 CPU_AUDSYNC
GNDD
GNDD
9
10
Pitch=1.0mm 9
10
GNDD
GNDD
H H 1/5 - H 5/5 LCDB ASSY (DWX3693) 13
14
CPU_AUDATA3
CPU_TxD
(DWX3695) (DWX3694) CN5001
CKS5956-A
SD_DATA2
SD_DATA3
SD_DATA0
SD_DATA1
SD_CMD
SD_DET
USB_STOP 11 USB_STOP
SD_CL
11 15 CPU_RxD
GND2
GND
VDD
USB_DN_A
USB_DP_A
USB_DN_B
USB_DP_B
SD_DATA2
SD_DATA1
SD_DATA0
SD_DATA3
USB_ILM_G 12 12 USB_ILM_G
V+5_USB
V+5_USB
16 CPU_EMU_BRK
SD_CMD
SD_DET
SD_CLK
SD_WP
*HORIZONTAL *HORIZONTAL *VERTICAL
V+3R3
VBUS
GNDD
USB_ILM_R 13 13 USB_ILM_R
GND
GND
17 CPU_RST
GND
GND
GND
CN5102 CN5101 CN5002
8
S_LED_PWM
10
PNL_CNVSS
S_LED_RCK
USB_ILM_G
S_LED_SCK
USB_ILM_R
USB_ILM_B
14
PNL_BUSY
USB_ILM_B USB_ILM_B
SD_ILM_G
SD_ILM_R
SD_ILM_B
MAT_SEL4
14 18
EUP_CON
GNDD
S_LED_SI
AKM1291-A
PNL_RXD
VKN1414-A
PNL_SCK
PWR_SW
PNL_TXD
PNL_RST
V+12LED
V+12LED
AKM1293-A
TCP_XIN
TCP_YIN
ENC_SW
TCP_YV
TCP_XV
KYE5_B
V+3R3E
SD_SW
V+12FL
10
1
7
V+3R3
V+5R2
V+5R2
V+5R2
V+5R2
2
ENC_1
V_DET
ENC_2
GNDD
GNDD
GNDD
GNDD
GNDD
1
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
19 DSP_TMS
KEY2
KEY1
OUT2
OUT1
VKN1431-A VKN1431-A
20 DSP_TDI DDA1052- DDA1053-
*VERTICAL *VERTICAL
SHIELDED SHIELDED DDD1706-
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
21
9
1
9
DSP_TDO FFC(SAME FACE)
CONN-CABLE CONN-CABLE
CN4005 CN4004 22 DSP_TCK AWG #26/#28 AWG #26/#28 L=70mm
Pitch=1.0mm
DDD1707- L=85mm L=120mm
DDD1707- 23 DSP_EMU0
FFC(REVERSE FACE) FFC(REVERSE FACE) 24 DSP_TRST
SD_DATA3 10
2
1
9
L=60mm L=60mm
CN601 CN603 CN604
GNDD
GNDD
USB_DN_A
USB_DP_A
V_BUS_B
Pitch=1.0mm
GND
SD_WP
SD_DATA2
SD_DATA1
SD_DATA0
GNDD
SD_CLK
V+3R3
SD_CMD
SD_DET
GNDD
GNDD
Pitch=1.0mm
USB_DN_B
USB_DP_B
V+5_USB
V+5_USB
AKM1291-A AKM1278-A-TBB CKS6095-A
*HORIZONTAL
CN8002 CN8001 *VERTICAL *VERTICAL
S_LED_RCK 27
EUP_CON 26
PNL_CNVSS 25
PWR_SW 24
ENC_1 23
V_DET 22
ENC_2 21
S_LED_PWM 20
ENC_SW 19
S_LED_SCK 18
MAT_SEL4 17
S_LED_SI 16
OUT2 15
PNL_BUSY 14
OUT1 13
PNL_SCK 12
GNDD 11
PNL_TXD 10
9
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1
VKN1287-A VKN1287-A
GNDD
PNL_RXD
GNDD
GNDD
PNL_RST
GNDD
GNDD
GNDD
V+3R3E
*VERTICAL
CN4002
V+12FL
GNDD
GNDD
V+12LED
V+12LED
V+3R3
KYE5_B
SD_ILM_G
KYE2
SD_ILM_R
KYE1
USB_ILM_B
SD_SW
USB_ILM_R
SD_ILM_B
USB_ILM_G
TCP_YV
TCP_XIN
TCP_XV
TCP_YIN
V+5R2
V+5R2
V+5R2
V+5R2
GNDD
GNDD
GNDD
*HORIZONTAL *HORIZONTAL *HORIZONTAL CN1701
CN6304
VKN1431-A
CN8004 VKN1434-A CKS6025-A
*HORIZONTAL *HORIZONTAL
VKN1287-A *VERTICAL
CN605 LAN
V+5R2 27 1 V+5R2 GND 1 1
GNDD
DKN1445-A
NM
CONNECTOR
V+5R2 26 2 V+5R2 TCP_SCLK 2 2 TCP_SCLK
GNDD 25 3 GNDD TCP_SDA 3 3
TCP_SDA
V+3R3_CPU 1
JA601
GNDD 24 4 GNDD GND 4 4 V+3R3_CPU 2 VKN2023-A
I
GNDD
CUEA_B 23 5 CUEA_B SH2_RSPCK1 5 5 GNDD 3
SH2_RSPCK1
2
2
CUEA 22 6 CUEA SH2_SSL10 6 6 GNDD 4
SH2_SSL10
SH2_MOSI1 REST_ER
CUEA_R 21 7 CUEA_R
GND
7 7
SH2_MOSI1
CPU_TRST
5
JA901
CUEB 20 8 CUEB 8 8
GNDD 6 PKB1045-A
PNLB ASSY
CUEA_G 19 9 CUEA_G SH2_MISO1 9 9 CPU_TDI 7 1
SH2_MISO1
2 DIGITAL
HLED ASSY (DWX3700)
N
CUEB_B 17 11 CUEB_B PENIRQ CPU_TCK 3
O
11 11 9
PENIRQ
CUED 16
CUEB_G 15
CUEB_R 14
DDD1712-
FFC
(REVERSE FACE)
12
13
14
CUED
CUEB_G
CUEB_R
(DWX3702) JH8003 CN8651
GND
V+1R2
V+3R3
12
13
14
DDD1705-
FFC
12
13
14
GNDD
V+1R2
CPU_AUDSYNC
CPU_TDO
CPU_MPMD
10
11
12
L=165mm V+3R3
CN8502 JH8001
51048-0600 52147-0610
JA801
E E 1/11 - E 11/11
V+3R3 CPU_AUDATA3
EUPB ASSY
CUEC_R 13 15 CUEC_R 15 (SAME FACE) 15
CDJ-2000NXS2
13
KSWB ASSY
Pitch=1.0mm V+3R3 DKB1121-A
CUEC_B 12 16 CUEC_B 52147-0810 51048-0800
KEY4_B 1 1 KEY4_B GND 16 L=180mm 16 CPU_AUDATA1 14
GNDD
Pitch=1.0mm 1
CUED_B 11 17 CUED_B GNDD V+12 17 17 CPU_AUDATA0 15 L
2 2
D_INDL 1 1 D_INDL GNDD V+12
2 AUDIO
(DWX3704)
JP8003 CPU_EMU_BRK
(DWX3703)
CUEC_G 10 18 CUEC_G MAT_SEL4 V+12 18 18 16
PLAY 2 2 PLAY 3
D20PDY0605E
3 MAT_SEL4
V+12 3 OUT
CUED_G 9 19 CUED_G V+5R2 JUMPER WIRE PNL_RST 19 19 CPU_RST 17 R
CUE 3 3 CUE 4 4 V+5R2 PNL_RST
L=50mm 4
SH2_RESET
V+12
PWR_SW 28 28
DDD1641- PWR_SW
GND FOR DEBUG (DSP&CPU)
FFC 29 29
GNDD S801
M
*VERTICAL *HORIZONTAL (SAME FACE) V+12_EUP 30 30 ASG1102-A
L=75mm JH8002 CN8701 V+12_EUP Only Proto
CN6302
VKN1425-A
CN8003
VKN1281-A Pitch=1.0mm 51048-0900 52151-0910
V+3R3E 1 1 V+3R3E
2
4
1
V+12LED 21 1 V+12LED
GNDS GNDS
CN6201 2 2
SLDB ASSY
V+12
GNDD
GNDD
D_INDIL
V+12FL 20 2 V+12FL
RKN1045-A KYE3_B 3 3 KYE3_B
GNDD 19 3 GNDD
ATA_RESET
ATA_DREQ
ADCT ADCT
ATA_DACK
4 4
ATA_DIOR
JP8002
GNDD 18
ATA_RDY
ATA_CS0
ATA_CS1
4 GNDD
ATA_D10
ATA_D11
ATA_D12
ATA_D13
ATA_D14
ATA_D15
ATA_WR
ATA_INT
ATA_D7
ATA_D8
ATA_D6
ATA_D9
ATA_D5
ATA_D4
ATA_D3
ATA_D2
ATA_D1
ATA_D0
(DWX3705)
ATA_A1
ATA_A0
ATA_A2
D20PDY0910E
V+5S_D
ADIN ADIN
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
5 5
standby
*HORIZONTAL
INDB ASSY
V+12S
V+12S
*HORIZONTAL
V+12S
V+12A
V+12E
JUMPER WIRE *HORIZONTAL
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD 17 5 GNDD
V+12
V+12
J
GNDD 16 6 GNDD
OUT3 6
L=100mm 6 OUT3 CN1501 CN1502 CN602
MAT_SEL3 MAT_SEL3 DKN1661-A AKM1292-A VKN1818-A
7 7
36
37
38
39
40
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
10
15 7 GNDD
9
1
6
2
GNDD
(DWX3699)
GNDD 8 8 GNDD
GNDD 14 8 GNDD
V+5R2 9 9 V+5R2
V+5R2FL 13 9 V+5R2FL DDC1024- PF06PP-S10 DDD1703-
3
DDD1709-
3
CRIMP CONNECTOR CRIMP CONNECTOR FFC(SAME FACE)
V+5R2FL 12 FFC 10 V+5R2FL
(REVERSE FACE) L=144mm L=100mm L=90mm
KEY5 11 11 KEY5 AWG #24
L=95mm AWG #22 Pitch=0.5mm
J_SCLK 10 12 J_SCLK
Pitch=1.0mm
KEY0 9 13 KEY0
standby 10
1
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1
2
6
1
JOG_SW 8 14 JOG_SW
CN2 CN7002 CN7005
V+12
V+12
V+12
V+12A
V+12E
GND
GND
GND
GND
ATA_RST
GNDD
ATA_D7
ATA_D8
ATA_D6
ATA_D9
ATA_D5
ATA_D10
ATA_D4
ATA_D11
ATA_D3
ATA_D12
ATA_D2
ATA_D13
ATA_D1
ATA_D14
ATA_D0
ATA_D15
GNDD
GNDD
ATA_DREQ
GNDD
ATA_WR
GNDD
ATA_DIOR
GNDD
ATA_RDY
GNDD
ATA_DACK
GNDD
ATA_INT
GNDD
ATA_A1
GNDD
ATA_A0
ATA_A2
GNDD
ATA_CS0
ATA_CS1
GNDD
V+12S
V+12S
GND
GND
GND
V+5S_D
MAT_SEL1 7 15 MAT_SEL1 B10B-PASK AKM1292-A
*VERTICAL VKN1818-A
*HORIZONTAL
J_DSO 6 16 J_DSO
AC INLET ASSY CN1 *HORIZONTAL
5 B2P3-VH
OUT1 17 OUT1 DKP3975- *VERTICAL
Q
4 18 J_BK_N
J_BK_N
3
L
19 OUT2 LIVE(YELLOW) L=120mm
OUT2 LIVE
2 LIVE LIVE 2 NC
V+5S_D
20 V+3R3
GNDSD
GNDSD
NEUTRAL(WHITE) L=120mm
V+3R3 *HORIZONTAL
EARTH EARTH NEUTRAL *HORIZONTAL
INSW
LPS1
LPS2
HW+
1 NEUTRAL
HU+
HV+
HW-
(DWX3709)
LO+
1
CN7009
HU-
21 J_LAT
HV-
CN7003
LO-
J_LAT NEUTRAL NEUTRAL EARTH(GREEN YELLOW Stripe)
HB
W
U
V
L=63mm
SW POWER
AKM1291-A DKN1313-A
10
11
12
13
1
9
1
5
2
PF05PP-C25 DDD1704-
Use "C13" type AC POWER CORD
CRIMP CONNECTOR FFC(SAME FACE) DKP3769-
SUPPLY
V+3R3
GNDD
JOG2
JOG1
C
/UXJCB DDG1108-
13
12
11
10
1
1
5
2
JP9201
V+5S_D
HU+
HU-
HV+
HV-
HW+
HW-
HB
U
V
W
GNDSD
INSW
LO-
LO+
GNDSD
LPS1
LPS2
D20PYY0405E /SYXJ ADG1244- KM200NA5L DKN1313-A
JUMPER WIRE *HORIZONTAL *HORIZONTAL
D
L=50mm /JXJ DDG1110-
INSW ASSY
/FLXJ ADG1244-
1
JH9201 ADG1239-
JOG2
JOG1
V+3R3
GNDD
B SPCN ASSY
51048-0400
/AXJ DDG1114-
CN9201
K JOG FL (DWX3707)
INSW 1 1 INSW
VKN1425-A VKN1252-A
GNDSD 2 2 GNDSD
JOG1 1 21 JOG1 V9201
CN6001
V+5S_A
GNDSA
VRCOM
V+5S_D
GNDSA
GNDSA
VREF1
A_S1
ST1+
ST2+
VR65
VR78
DEL1074-A
LD78
LD65
ST1-
ST2-
CN6102
A_D
A_C
HW+
7/x6
*HORIZONTAL
CN7001
HU+
CN7004
HV+
HW-
A_B
A_A
HU-
RF
HV-
JFLB ASSY
NC
NC
PD
HB
T+
F+
V+3R3 3 19 V+3R3
F-
VKN1940-A
W
T-
U
V
DKN1445-A DKN1288-A DKN1312-A
V+12LED 4 18
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
V+12LED
10
11
12
1
4
2
9
JOGILM_W 5 17 JOGILM_W
J_DSO
JOGILM_R
6
7
16
15
J_DSO
JOGILM_R (DWX3708) DDD1713-
FFC(SAME FACE)
L=118mm Pitch=0.5mm
4
4
J_BK_N 8 14 J_BK_N
CN9202
JOG_SW
GNDD
*HORIZONTAL ZWNN1007G28-8-07A
J_LAT 10 FFC 12 J_LAT L=70mm GRAY Single Wire
LO+ DC MOTOR
1
(REVERSE FACE)
3
GNDD 11 11 GNDD
10
11
12
A_B 10
A_A 11
VR65 12
VRCOM 13
VR78 14
GNDSA 15
LD78 16
PD 17
LD65 18
GNDSA 19
NC 20
T+ 21
T- 22
F+ 23
F- 24
L=95mm ASSY-S
9
1
2
1
4
J_SCLK 12 10 J_SCLK LO-
Pitch=1.0mm (DXX2510)
GNDSA
A_S2
VREF1
V+5S_A
A_S1
A_D
A_C
7/x6
RF
NC
W
HB
HW-
HW+
HV-
HV+
HU-
HU+
V+5S_D
GNDD ZWNN1007G28-9-07A
13 9 GNDD
ST1+
ST2+
ST1-
ST2-
GNDD 17 5
V+5R2FL
09SD PICK UP ASSY SPNDIE MOTOR G11
GNDD
V+12FL 18 4 V+12FL
SHEET SW STEPPING
GNDD 19 3 GNDD
GNDD 20 2 GNDD (DSX1078-) MOTOR SK
GNDD 21 1 GNDD
JOG_SW
TM ASSY 09SD-S (DXX2697)
DE007VE0
EARTH LEAD WIRE
L=75mm SLOTIN MECHA G11 ASSY
4.2 SIGNAL BLOCK DIAGRAM
TOUCH PANEL LCD MODULE
1-4
CN5001 JA5101 JA5102
CN4401 CN4801 CN4802
SD Card USB Jack USB Jack
J DIGITAL RGB Connector A TYPE B TYPE
HLED ASSY IC4601 32MB SDRAM
CN6301
CN4001
KEY 5,11 5,11
32
6-8, 6-8,
IC4604
5
5
H
LCDB ASSY
CN4005 CN4004 CN4002 CN5002 CN5102 CN5101
4 8,10,12 13 17-20
8,9,1 3,4 2,3
14-16 26,28
POWER POWER
20,18,16 26,28 3,2,10 3,4 2,3
24 14-16 15 11-8
POWER IC603
LED KEY
USB-HUB USB LAN 10-13 4,5
VR8001 VR8002
SWITCH 3,4 7,8 IC602 2-5 4-7 LAN 7,8
22,20,
TOUCH / BRAKE RELEASE / START IC604 JA601
18,16
USB-LAN
8-15,17, 13-20, USB I/F LAN-HUB
19,21,23 11,9,7,5 RMII 1,2
LAN
76,78,
6,8,10,12 80-82,88 Connector
19 100 84-87 95 97
CONFIG
KEY 50-47
CN6304
CN8004
LED 42-45,52-59
IC12
6
6
CN8003
CDJ-2000NXS2
IC7006
7
7
IC7004
128kB FLASH
13 CN7009 CN7004 CN7003 CN7001 9
O 9-11 1-4 4,5 2,1
21-24
KSWB
N M ASSY Q 4,5 2,1
EUPB ASSY SLDB ASSY SW POWER SLOTIN MECHA
CN6303 CN8501 SUPPLY ASSY CN9001
3-5
15,17 13 2,1 1
ASSY
1 CN6101
M
7,5 9 20,21 1,2 1,2 4 B
CN9201 CN6201 SPCN ASSY 1 D LOADING
SLMB MOTOR
CN9301
JH9201
L CN6103 CN6102
ASSY
LED
JOGB 2-4
ASSY LED
1
PC9301
8
8
CN6001 CD/DVD
M M
Vinyl JOG FL C
INSW ASSY
SPDL STEPPINGING OEIC
CN9202
A
F
1
DCDC LDO Regulator Other Device (Voltage)
Q E H N CN4001 CN6301
K
SW POWER MAIN ASSY LCDB ASSY EUPB ASSY V+12
3 Color
JFLB ASSY
SUPPLY ASSY 1,
2
1,
2 LED
STBY
Touch
O
LED
Pannel
CN4005
CN8002
CN2 CN1501 V+12E CN1701 CN4002
Mute KSWB ASSY JOG
LED
(+12V) V+12E V+12E V+12E IC4204 V+3R3E V+3R3E
IC8001
5 5 for Ever 30 30 2 DCDC 3 27 1 PANEL CPU
(+12V) BD9328EFJ (+3.3V) R5F364AENFA
AC V+12LED V+12LED V+12LED
(+12V) V+12 V+12 V+12 Q4202 V+12LED D9203 IC9201 V+3R3_JFL
Q161 2, 2, 17, 17, 4, 24,
for System Over 1 21 4 18 Diode 1 LDO 5 1
12V FETSW 3 3 18 18 5 23
Current MM1856A33N (+3.3V)
Trans. V+12 V+1R2
IC1502 V+1R2 V+1R2_SH2 detect
V+12S 2 DCDC 3 LED LED D9201, R9201/02 D9202
IC4604
1 1 for Servo (+12V) BD9328EFJ (+1.2V)
V+3R3_CPU IC14 Apple IC Ctrl Circuit Q1
13 13
V+3R3_SH2
GUI CPU
SH7269
J 6.2V Zener
+ Resistor
Diode
8 H337S3959 FETSW
HLED ASSY
LED
(+12V) V+12A V+1R2_CPU IC10
Q151 V+12 V+5USB V+3R3_NIC
4 4 for Audio IC606 IC607 IC602 USB-LAN MAIN CPU V9201
USB-A
FETSW 2, 6,
Jack
2 DCDC 3 Hi-Side 1,10,13 RTL8152B IC1501 SH7724 V+
3 7 IC4602
BD9328EFJ SW V+3R3 V+1R8_CPU V+3R3_SH2 Q4201 V+12FL V+12FL V+12FL 12FL V+12FL IC9203 V+26 V+26 JOG FL
(+12V) (+5V) LDO IC1, IC2 FLASH
V+3R3_USB_HUB IC603 USB HUB 4 MM3529A 5 DDR2*2 Over 1 27 2 20 18 4 6 DCDC 1 28 (DC Filament)
IC4601,4603
2
18P
2
USB2512B (+3.3V) (+1.8V) (1.8V) Current (+12V) NJM2392M (+26V)
V+3R3_CPU SDRAM*2
Enable IC12 detect
F V+3R3_LAN_HUB IC604 LAN HUB
RTL8304E
Ctrl Circuit 37 FLASH
(3.3V) V+12 V+5R2
LED LED
IC4202
USBA ASSY 3
2 DCDC 3
21-
V+5R2
7- 1,
V+5R2
27, LED 14, 8,
V+12 V+3R3DDC 24 4 2 26 16 6
IC1503 V+3R3 V+3R3 (+12V) BD9328EFJ (+5.2V)
Q1506 CN8004 V+5R CN6304 V+5R
2 DCDC 3 14, 14, Enable 2FL 2FL FLDC+
FETSW 15 15 9, 13,
(+12V) BD9328EFJ (+3.3V) 23
10 12
(+5.2V)
Ctrl Circuit V+1R2_FPGA V+3R3 V+3R3 V+3R3
CDJ-2000NXS2
(+0.75V) (1.5V)
3
V+3R3DSP (+1.5V)
V+5S_D Driver SmartReflex
PickUp 3
for CVDD
D7001 Diode 28 BD7956FS V+0R75VREF W631GG6KB
LM10011 R503,504 -15
D7002 Diode LD drive
1k //1k
V+5S_D (+0.75V)
V+12S IC7010 V+5S_A Spindle
1 LDO 3 IC7002 V+12A IC1007 V+5SPDIF V+5SPDIF
IC901
FEP V+5S_D
(+12V) NJM2845DL1-05 (+5V) IC7004 1 LDO 5 14 SPDIF Buffer
FLASH NJM2872BF05 NLV74VHCU04DT
AN22022A 8 (+12V) (+5V)
X1202,1203 IC1204 IC1216
V+5S_D V+5S_D 22/24MHz Oscillator Analog SW 3.3-1.8Trans
V+3R3DAC_D V+3R3DAC_D
4 16 1
48
V+5S_D IC7003 V+3R3S_A V+3R3S_A V+12A IC1003 V+3R3DAC_A
2 LDO 4 1 LDO 5 V+3R3DAC_A
IC7006
(+5V) NJM2846DL3-33 (+3.3V) SODC (+12V) NJM2872BF33 (+3.3V) 44
IC801
V+3R3S_D V+3R3S_D
V+5DAC_L DAC
MN103S71F V+12A V+12A IC1001 V+5DAC_L
33,34,
1 Reg 3 AK4490EQ
41,42
V+5S_D IC7005 V+1R5S V+1R5S NJM7805DL1A
(+12V) (+5V)
4 LDO 5
V+5DAC_R
S-1155B15-U5 V+12A V+12A IC1002 V+5DAC_R
(+5V) (+1.5V)
19,20,
1 Reg 3
27,28
(+12V) NJM7805DL1A (+5V)
4
5 6 7 8
5. DIAGNOSIS
5.1 SEQUENCE
POWER ON SEQUENCE A
Pin G4 of MAIN CPU Pin 88 of GUI CPU Pin 12 of PANEL CPU Pin 45 of SODC
(IC10) cancels reset (IC4604) cancels reset (IC8001) cancels reset (IC7006) cancels reset
at H. at H. at H. at H.
Initialization of the MAIN CPU Initialization of the GUI CPU Initialization of the PANEL CPU Initialization of the SODC
Initialization of the SDRAM Initialization of the SDRAM Initialization of the Jog FL Initialization of the B
loading mechanism
Program transfer from Program transfer from
FLASH to SDRAM FLASH to SDRAM
Program transfer to
DSP
CDJ-2000NXS2 13
5 6 7 8
1 2 3 4
A SETUP SEQUENCE
Power ON
Loading of a disc
Stepper moving to a
focusing position
B Offset canceling
Media distinction with the aid of reflectivity, by alternately emitting light from the LDs on the CD and DVD sides.
With the LD corresponding to the loaded medium found as a result of media distinction, focus search is
performed to acquire S-shaped signal data.
C
Judged as a CD Judged as a DVD
LD OFF LD OFF
Offset canceling for the 2nd time Offset canceling for the 2nd time
CD_LD ON for the 2nd time DVD_LD ON for the 2nd time
Focusing in Focusing in
D
Media distinction with the aid Coarse adjustment of
of a sync signal (only for CD) focus position
Coarse adjustment of
Coarse adjustment of focus position Tr Drive offset adjustment
focus position
14 CDJ-2000NXS2
1 2 3 4
5 6 7 8
Check method
Measure the voltage at the probe pad on the SRVB Assy (see the photo below), using a tester.
∗ To check lighting of each LD, follow the procedure indicated in "[7] Checking the servo operations of the drive unit" in
"6.1 SERVICE MODE."
∗ Note that the LD may be degraded if the probes of a tester are applied to or pulled away from the probe pad with the LD ON.
Procedures
1. With the LD OFF, apply the probes of a tester to the reference probe pad (LDCHK) and 78CHK (CD side) or 65CHK
(DVD side).
2. With the probes kept applied to the above-mentioned pads, turn the LD ON to measure the voltage between them. C
3. After measurement, turn the LD OFF (ALL OFF) then pull the probes away.
4. Calculate the current value by dividing the measured voltage value by the resistance value mentioned below.
(For CDs: R7008 = 22 ohms, For DVDs: R7007 = 12 ohms)
Failure judgment:
If the calculated current value exceeds the maximum value, the LD has been degraded
78CHK
IC7002
D
65CHK
LDCHK
• Focus side
Disconnect* the FFC connected to the CN7001 then measure the resistance value between FFC pins 23 and 24.
• Tracking side
Disconnect* the FFC connected to the CN7001 then measure the resistance value between FFC pins 21 and 22. F
Failure judgment:
A value out of the range of the specifications is judged as failure.
CDJ-2000NXS2 15
5 6 7 8
1 2 3 4
5.3 TROUBLESHOOTING
A In this section, causes of failure, diagnostics points, and corrective measures can be searched for according to symptoms.
Before disassembling this unit, it is recommended to infer a failure point by performing a status check and referring to the error
code.
For the relationship of each power-supply and signal system, see "4. BLOCK DIAGRAM,” and “10. SCHEMATIC DIAGRAM."
If software of the product is updated before performing diagnostics, check that software updating has been performed properly
before proceeding to diagnostics.
If software updating has not been performed properly, update the software, following the instructions in "[9] Firmware update"
of "6.1 SERVICE MODE."
Contents
[0] Prior Confirmation [6] AUDIO OUT
[1] Failure in Startup [7] ATAPI DRIVE
[2] Display (Jog FL/LED) [8] DRIVE ASSY
B
[3] Operations [9] EUP mode
(Button/Volume/Rotary enncoder / Jog dial / Touch panel) [10] SERVICE MODE
[4] USB (Type A/Type B), SD card [11] Error Codes
[5] LAN [12] Power Monitoring
The waveform numbers confirmation-point numbers (10.27 WAVEFORMS) described in this section correspond to the
numbers on the "10. SCHEMATIC DIAGRAM" and "11. PCB DIAGRAM."
Be sure to check the failure points, as well as check for failure in their peripheral circuits.
Fig. 1
E
[0-3] Checking Cables
No. Cause Diagnostics Point Item to be Checked Corrective Action Reference
1 Disconnection, Cables Check that all the cables are securely Securely connect the cables. If a cable is broken, 4.1 OVERALL
breakage, or connected. replace it. WIRING DIAGRAM
loose connection Check that there is no breakage in the 10. SCHEMATIC
of cables cables. DIAGRAM
16 CDJ-2000NXS2
1 2 3 4
5 6 7 8
2 The SW power PNLB Assy, Check V+3R3E. The DCDC converter (IC4204) may be loosely —————
does not function LCDB Assy connected with its peripheral devices or a part may
properly. be defective. Correct loose connection. If the
symptom persists, replace the defective part.
3 The EUP control SW POWER Check the standby signal. If the signal of standby (CN2 pin 10) is L, check the —————
unit does not SUPPLY Assy output of the SW POWER SUPPLY Assy.
function properly. If V+12 or V+12A (CN2 pins 1 to 4) is not output,
the SW POWER SUPPLY Assy is defective.
Replace it.
4 Various power MAIN Assy, Check each power-supply IC. The power IC and its peripheral devices for each —————
supply ICs do LCDB Assy power supply may be loosely connected or a part
not function may be defective. Correct loose connection.
properly. If the symptom persists, replace the defective part. B
5 Defective MAIN Assy Check the CPU_RST signal. If CPU_RST is "L" although the V+3R3_CPU is —————
CPU_RST signal normal, the RESET IC (IC11) is defective or the
relevant connection is poor.
Correct loose connection. If the symptom
persists, replace the defective part.
6 Defective MAIN Assy Check the SYS_CLK (=33.333333 MHz) The X2 or Logic IC (IC9) may be loosely connected 10.27 WAVEFORMS
SYS_CLK signal signal. with its peripheral devices or a part may be defective. 1
Correct loose connection. If the symptom persists,
replace the defective part.
CDJ-2000NXS2 17
5 6 7 8
1 2 3 4
2 Defective JFLB Assy Check that the FL (V9201) control line is Check the connection and correct loose 10.27 WAVEFORMS
control signal properly connected in the JFLB Assy. connection. 9
• J_SCLK As the Jog FL is controlled by the PANEL CPU
• J_BK (IC8001), if no signal is output, check the
• J_LAT PANEL CPU (IC8001).
B • J_DSO
3 Defective Jog FL ————— If the symptom persists after the above Replace the Jog FL. —————
corrections,
C 3 Defective PANEL PNLB Assy If the symptom persists after the above Check the connection between the PANEL CPU —————
CPU corrections. (IC8001) and the LED in question. If the connection
is OK, the port may be damaged. Replace it.
[3] Operations (Button / Volume / Rotary encoder / Jog dial / Touch panel)
As operations of all buttons, variable volumes, rotary encoder , Jog dial and Touch panel can be checked in Service mode, it is
recommended to check operations of those controls in Service mode before proceeding to the subsequent checks.
(For details, refer to "6.1 SERVICE MODE.")
[3-1] No key functions.
No key functions. (except USB STOP button)
No. Cause Diagnostics Point Item to be Checked Corrective Action Reference
1 Defective PNLB Assy Check if there is loose connection on the If there is no loose connection and if the signal —————
D
Power SW signal line from the PANEL CPU (IC8001) does not become L when the Power SW is
up to the SW. pressed, that SW is defective. Replace it.
2 Defective PNLB Assy Check the RST signal of the PANEL CPU If Pin 12 of IC8001 is "L" although the V+3R3E is —————
RST signal of (IC8001 pin 12). normal, the RESET IC (IC8002) or Q8015 is
PANEL CPU defective or the relevant connection is poor.
Correct connection or replace the defective part
with a new one.
3 Defective PNLB Assy Check the CLK signal of the PANEL CPU The X8001 may be loosely connected with its 10.27 WAVEFORMS
CLK signal of (IC8001 pin 13 = 4 MHz). peripheral devices or a part may be defective. 8
PANEL CPU Correct loose connection. If the symptom persists,
replace the defective part.
4 Defective PANEL PNLB Assy If the symptom persists after the above Check the connection of the PANEL CPU —————
CPU corrections. (IC8001). If the connection is OK, the port may
E be damaged. Replace it.
The USB STOP button does not function. (The signal from the USB STOP button is input to the MAIN CPU.)
No. Cause Diagnostics Point Item to be Checked Corrective Action Reference
1 Defective SW HLED Assy, Check if there is loose connection on the If there is no loose connection and if the signal —————
MAIN Assy signal line from the MAIN CPU (IC10) does not become L when the SW is pressed,
up to the SW. that SW is defective. Replace it.
2 Defective MAIN Assy If the symptom persists after the above The MAIN CPU (IC10) is defective. —————
MAIN CPU corrections. Replace the MAIN CPU (IC10).
18 CDJ-2000NXS2
1 2 3 4
5 6 7 8
2 Defective PANEL PNLB Assy If the symptom persists after the above Check the connection of the PANEL CPU —————
CPU corrections. (IC8001). If the connection is OK, the port may
be damaged. Replace it.
2 Defective PANEL PNLB Assy If the symptom persists after the above Check the connection of the PANEL CPU —————
CPU corrections. (IC8001). If the connection is OK, the port may
be damaged. Replace it.
2 Defective JOG section Check if there is any foreign object Remove any foreign object, if present. —————
SW ring between the SW ring and Holder.
and
Holder Check if the cushions that are adhered to Replace the SW cushion with a new one. —————
the Holder and SW ring have worn out.
CDJ-2000NXS2 19
5 6 7 8
1 2 3 4
Resistance to turning the Jog dial is too strong. (The load value for the Jog dial is outside the specified range.)
No. Cause Diagnostics Point Item to be Checked Corrective Action Reference
C 1 Improper adjust- JOG section Check that the load value for the Jog dial If it is outside the specified range, adjust the position —————
ment of the Jog is within the specified range, referring to of the Adjust plate to change the load value for the
dial or defective “Measuring method” in “8.4 JOG DIAL Jog dial, referring to “How to Adjust” in “8.4 JOG DIAL
washer, gear, or ROTATION LOAD ADJUSTMENT.” ROTATION LOAD ADJUSTMENT.”
cam plate During the above adjustment, if the lower-limit —————
adjustment position of the Adjust plate is reached,
shavings from the worn-out washer may have
increased the friction. Replace the washer, gear,
and smoother with new ones, then reassemble.
After replacement, adjust the position of the Adjust
plate to change the load value for the Jog dial.
3 Defective PNLB Assy Check the touch panel input signal If the waveform is abnormal, go to 4. —————
PANEL CPU (Pins 84 and 85 of IC8001) at the If the waveform is OK, the PANEL CPU (IC8001)
PANEL CPU (IC8001). may be in failure. Replace it.
4 Defective LCDB Assy Check the touch panel control signal Check operations of the circuits between IC8001 10.27 WAVEFORMS
Touch panel (Pins 1–4 of CN4401). and CN4401 to identify the part in failure, then cdef
repair or replace the part in question. If there is Note: The reference
E no problem with those circuits, the touch panel waveforms are those to
itself is in failure. Replace it. be indicated when the
center of the screen or
its periphery is touched.
20 CDJ-2000NXS2
1 2 3 4
5 6 7 8
3 The USB MAIN Assy Check the CPU_USB_HSTPWREN and If the CPU_USB_HSTPWREN signal does not —————
POWER SW IC HSSW_PWRFL signals from the become H, check the connection. If the
or its control USB POWER SW IC (IC607). connection is OK, then the MAIN CPU (IC10) is
signal is defective. defective. Replace the MAIN CPU (IC10). If the
HSSW_PWRFL signal does not become H, the
USB POWER SW IC (IC607) is in a state of
shutdown caused by abnormally high
temperature. Check the connection. If the
connection is OK, then the port may be
damaged. Replace it.
4 Defective MAIN Assy Check the DC/DC converter for Analyze DC/DC converter for V+5USB (IC606) —————
DC/DC V+5_USB (IC606) or and peripheral circuit. Identify a defectiveness
converter for check the peripheral circuit. element and replace it.
V+5_USB or B
peripheral circuit
5 Defective MAIN Assy Check the USB_CLK (= 48.000 MHz) The X1 may be loosely connected with its 10.27 WAVEFORMS
USB_CLK signal signal. peripheral devices or a part may be defective. 2
Correct loose connection. If the symptom
persists, replace the defective part.
6 Defective MAIN Assy If the symptom persists after the above The MAIN CPU (IC10) is defective. —————
MAIN CPU corrections. Replace the MAIN CPU (IC10).
3 Loose connections MAIN Assy Check the connections of the The communication line may be loosely —————
in the USB signal. communication line (USB_D+, USB_D-). connected. Correct it if it is.
If connection is proper, go to 4.
4 Defective MAIN Assy Check the USB_CLK (= 48.000 MHz) The X1 may be loosely connected with its 10.27 WAVEFORMS
USB_CLK signal signal. peripheral devices or a part may be defective. 2
Correct loose connection. If the symptom D
persists, replace the defective part.
5 Defective MAIN Assy If the symptom persists after the above The MAIN CPU (IC10) is defective. —————
MAIN CPU corrections. Replace the MAIN CPU (IC10).
[5] LAN
[5-1] No LAN communication
Check the following, with a peripheral device connected to the LINK terminal.
No. Cause Diagnostics Point Item to be Checked Corrective Action Reference
1 Loose connections MAIN Assy Check the connection of the periphery The communication line may be loosely —————
in the communi- circuit of LAN-HUB & PHY (IC604). connected. Correct it if it is.
cation line.
2 Defective MAIN Assy If the symptom persists after the above The LAN-HUB & PHY (IC604) may be defective. —————
LAN-HUB & PHY corrections. Replace it.
or If the symptom persists, the MAIN CPU (IC10) F
MAIN CPU may be defective.
Replace the MAIN CPU (IC10).
CDJ-2000NXS2 21
5 6 7 8
1 2 3 4
2 Defective MAIN Assy Check the MUTE signal (Q953 collector). The connection, or transistor may be defective. —————
MUTE signal While you usually playback, MUTE is Correct loose connection. If the symptom
canceled, and consist with around -12 V. persists, replace the defective part.
3 Loose connections MAIN Assy, Check the connection of the audio signal The signal line may be loosely connected. —————
in the signal line. JKSW Assy lines (ROUT, LOUT). Correct it if it is.
4 Defective MAIN Assy Check the DAC_MCLK The X1202, X1203 or logic IC (IC1204) may be 10.27 WAVEFORMS
B
DAC_MCLK (IC801 pin 46 = 22.5792 MHz) signal. loosely connected with its peripheral devices or 3
signal a part may be defective. Correct loose connection.
If the symptom persists, replace the defective part.
5 DAC or DSP MAIN Assy Check the digital inputs (IC801 pin 3, 4, 5 ) If the analog signal is not output although the —————
is defective. on DAC (IC801) and analog outputs digital signal is input, DAC (IC801) or one of its
(IC801 pin 25, 26, 35, 36). peripheral parts may be defective. If the digital
signal is not input, DSP (IC301) or FPGA
(IC1201) or one of its peripheral parts may be
defective. Correct loose connection. If the
symptom persists, replace the defective part.
3 Defective MAIN Assy Check the periphery circuit of the MAIN Check the periphery of the MAIN CPU (IC10). —————
MAIN CPU CPU (IC10). If no problem is found, the MAIN CPU (IC10)
may be defective. Replace the MAIN CPU (IC10).
2 Loose connections Loading mecha Check that the LP switch has been If soldering is improper, resolder it. —————
in the signal line. mounted.
3 Improper Loading mecha Check that the lever is engaged with the Engage the lever with the LP switch. —————
assembling LP switch.
4 Improper Loading mecha Check that the wires from the loading If they are not soldered, solder them. —————
soldering motor have been properly soldered.
5 Power supply SRVB Assy Check the power voltages (12 V, 5 V, Check the connection of the parts at the periphery of —————
error 3.3 V, and 1.5 V). the power-supply IC that does not output the voltage.
If the symptom persists after a corrective action, the
F power supply block is defective. Replace it.
6 LPS1 and LPS2 SRVB Assy Check the waveforms of the LPS1 and LPS2 The loading detection SWs (S9001 and S9002) may 5.4 OPERATIONAL
signal errors signal lines. (The LPS1 and LPS2 signals be improperly soldered or defective. Resolder them, WAVEFORMS
becomes L when the SW is set to ON.) if necessary. If the symptom persists, replace them. 2
22 CDJ-2000NXS2
1 2 3 4
5 6 7 8
7 MUTE1 and SRVB Assy Check the waveforms of the MUTE1 and DRIVER IC (IC7001) and SODC (IC7006) may —————
MUTE2 signal MUTE2 signals. (During loading, the be improperly soldered or defective.
errors MUTE1 signal is L and the MUTE2 signal Resolder them, if necessary. If the symptom
is H.) persists, replace SODC (IC7006).
8 LOAD signal SRVB Assy Check the LOAD signal. DRIVER IC (IC7001) and SODC (IC7006) may 5.4 OPERATIONAL
error be improperly soldered or defective. WAVEFORMS
Resolder them, if necessary. If the symptom 2
persists, replace SODC (IC7006).
9 Defective SRVB ————— If the symptom persists after the above Replace the SRVB Assy. —————
Assy corrections.
1 The main unit is Main unit Check if the main unit is positioned inclined. Place it on a level surface. —————
positioned inclined.
2 Improper assembling Traverse mecha Check if there is a missing or defective part at the If there is, install the missing part or replace the —————
section where the main axis and stepper contact. defective part.
3 Improper assembling Traverse mecha Check the inside switch. Assemble the INSW Assy properly. —————
4 Power supply SRVB Assy Check the power voltages (12 V, 5 V, Check the connection of the parts at the periphery of —————
error 3.3 V, 1.5 V, VREF1, VREF2 and VHALF). the power-supply IC that does not output the voltage.
If the symptom persists after a corrective action, the
power supply block is defective. Replace it.
5 INSW signal SRVB Assy Check the INSW signal. (The INSW The FFC cables that connect the traverse mechanism, —————
error becomes L when the INSW is set to ON.) SPCN, and SRVB are loosely connected, or the INSW
is defective. Reconnect them securely.
If the symptom persists, replace the INSW. C
6 MUTE1 signal SRVB Assy Check that the MUTE1 signal becomes H DRIVER IC (IC7001) and SODC (IC7006) may —————
error after loading is completed. be improperly soldered or defective.
Resolder them, if necessary. If the symptom
persists, replace SODC (IC7006).
7 Improper assembling Cables Check that the FPC cable that connects the If it does not, securely connect it. If it is broken, —————
traverse mecha and the SRVB Assy is replace the traverse mecha.
securely connected.
8 Signal error SRVB Assy Check that a sine-wave signal is input to The DRIVER IC (IC7001) may be loosely 5.4 OPERATIONAL
Pins 29 and 30 of DRIVER IC (IC7001). connected or defective. WAVEFORMS
Resolder them, if necessary. If the symptom 5 7 8
persists,replace SODC (IC7006).
9 Defective ————— If the symptom persists after the above Replace the parts in the order of (1) DRIVER IC —————
traverse mecha corrections. (IC7001), (2) SRVB Assy, then (3) traverse mecha.
D
[8-3] No playback
Neither a CD nor a DVD can be played back.
No. Cause Diagnostics Point Item to be Checked Corrective Action Reference
1 Short-circuit pad Traverse mecha Check if the LD short-circuit pad is If it is, open it. —————
short-circuited.
2 LD current SRVB Assy Check that the LD current is within the If there is any error, replace the traverse mecha. 5.2 FAILURE
specified range. JUDGEMENT OF THE
PICKUP ASSY
3 Power supply SRVB Assy Check the power voltages (12 V, 5 V, Check the connection of the parts at the periphery of —————
error 3.3 V, 1.5 V, VREF1, VREF2 and VHALF). the power-supply IC that does not output the voltage.
If the symptom persists after a corrective action, the
power supply block is defective. Replace it.
E
4 INSW signal SRVB Assy Check the INSW signal. (L at ON.) If the signal waveform is not proper, replace the —————
error INSW Assy.
5 MUTE1 signal SRVB Assy Check that the MUTE1 signal becomes H DRIVER IC (IC7001) and SODC (IC7006) may —————
error after loading is completed. be improperly soldered or defective.
Resolder them, if necessary. If the symptom
persists, replace SODC (IC7006).
6 Improper Traverse mecha Check if the objective lens is dirty. Clean the lens. —————
assembling
7 A–F signal error SRVB Assy Check the A–F signals (CN7001). Check that the signals fluctuate with 2.2 V at the center. —————
If a DC signal is not output, check the VREF1. If a DC
signal is not output from it, replace the FEP (IC7002).
If an AC signal is not output, check the soldering at the
CN7001–IC7002 of the pickup. If soldering is improper,
resolder it. If soldering is OK, replace the parts in the F
order of (1) FEP (IC7002), (2) DRIVER IC (IC7001),
(3) SODC (IC7006), (4) SRVB Assy, then (5) traverse
mecha.
CDJ-2000NXS2 23
5 6 7 8
1 2 3 4
2 Defective PNLB Assy Check that the signal from pin 18 of the The PANEL CPU (IC8001) may be defective. —————
PANEL CPU PANEL CPU (IC8001) changes from H to Check the soldering of the PANEL CPU (IC8001)
L during mode shift. and its periphery. If the soldering is OK, then
replace it.
3 Disconnection, SW POWER Check the standby signal The signal line cable may be defective. —————
breakage, or SUPPLY Assy (CN2 pin 10) changes from L to H If it is loosely connected, securely connect it.
loose connection during mode shift. If it is broken, replace it.
F of cables
4 Defective SW ————— ————— When there is not a problem with Step 3, the —————
POWER SUPPLY SW POWER SUPPLY Assy is defective.
Assy Replace it.
24 CDJ-2000NXS2
1 2 3 4
5 6 7 8
2 Defective PNLB Assy Check that the signal from pin 18 of the The PANEL CPU (IC8001) may be defective. —————
PANEL CPU PANEL CPU (IC8001) changes from H to Check the soldering of the PANEL CPU (IC8001)
L during mode shift. and its periphery. If the soldering is OK, then
replace it.
3 Disconnection, SW POWER Check the standby signal The signal line cable may be defective. —————
breakage, or SUPPLY Assy (CN2 pin 10) changes from H to L If it is loosely connected, securely connect it.
loose connection during mode shift. If it is broken, replace it.
of cables
B
4 Defective SW ————— ————— When there is not a problem with Step 3, the —————
POWER SUPPLY SW POWER SUPPLY Assy is defective.
Assy Replace it.
CDJ-2000NXS2 25
5 6 7 8
1 2 3 4
No tracking close
No. Cause Diagnostics Point Item to be Checked Corrective Action Reference
C 1 ————— Traverse mecha Check that focusing is in. (If focusing is See “In-focus not possible” above. —————
out, tracking close is not possible.)
2 Signal error SRVB Assy With a CD, check that the E and F signals Check that the signals fluctuate with 2.2 V at the center. 5.4 OPERATIONAL
fluctuate with 2.2 V at the center. If a DC signal is not output, check the VREF1. If a DC WAVEFORMS
With a DVD, check the A, B, C, and D signal is not output from it, replace the FEP (IC7002).
signals. If an AC signal is not output, check the soldering at the
CN7001–IC7002 of the pickup. If soldering is improper,
resolder it. If soldering is OK, replace the traverse
mecha.
3 TE signal error SRVB Assy Check that the TE signal fluctuates Check the connection of the parts at the periphery of 5.4 OPERATIONAL
with 1.65 V at the center. the FEP (IC7002). If soldering is improper, resolder it. WAVEFORMS
If soldering is OK, replace the FEP (IC7002). 4 5 6 7 8
4 TEDRV signal SRVB Assy Check that the TEDRV signal fluctuates If the output signal waveform is not proper, the connection 5.4 OPERATIONAL
error with 1.65 V at the center, and that a of the SODC (IC7006) and its periphery may be WAVEFORMS
D
pulselike signal is output during tracking loose or the parts may be defective. If the connection is 6 7 8
close. loose, reconnect securely. If the connection is OK,
replace the SODC (IC7006).
5 ————— ————— If the symptom persists after the above Replace the parts in the order of (1) FEP (IC7002), —————
corrections. (2) SODC (IC7006), (3) DRIVER IC (IC7001),
(4) SRVB Assy, then (5) traverse mecha.
26 CDJ-2000NXS2
1 2 3 4
5 6 7 8
4 The RESET MAIN Assy Check that the signals of the DSP_RST If the signal of the CPU_DSP_RST line is L, the —————
signal is not line are H. port of MAIN CPU (IC10) may be damaged.
properly input. If the signal of the DSP_RST line is L, check the
connection of the logic IC (IC8) and its periphery.
5 Loose connection MAIN Assy Check the connection between the Check the connections between MAIN CPU —————
between the MAIN MAIN CPU (IC10), FPGA (IC1201) and (IC10), FPGA (IC1201) and DSP (IC301).
CPU and DSP DSP (IC301). The signal line may be loosely connected.
Correct it if it is.
6 Loose connection MAIN Assy Check the connection between the Check the connections between DSP (IC301) —————
between the MAIN DSP (IC301) and SDRAM (IC501, IC502). and DDR3 (IC501, IC502). C
DSP and SDRAM The signal line may be loosely connected.
Correct it if it is.
7 ————— ————— If the symptom persists after the above Replace the MAIN CPU (IC10). —————
corrections.
2 Power is not MAIN Assy Check the power voltages of Check the connections of the power supply lines. —————
supplied properly. V+3R3_LAN_HUB line. The power line may be loosely connected.
Correct it if it is.
3 The clock is not MAIN Assy Check that the frequency at Check the connections between X604 and 10.27 WAVEFORMS
properly input. RMII_REF_CLK (IC604-pin 28) of LAN-HUB & PHY (IC604). 4
LAN-HUB & PHY (IC604) is 50 MHz. The signal line may be loosely connected.
Correct it if it is.
4 The RESET MAIN Assy Check that the signals of the ETHER_RST Check the connection of the ETHER_RST line. —————
signal is not line is H. The signal line may be loosely connected.
properly input. Correct it if it is.
5 Loose connection MAIN Assy Check the connections of communication Check the connections between MAIN CPU —————
between the line between the MAIN CPU (IC10) and (IC10) and LAN-HUB & PHY (IC604).
MAIN CPU and LAN-HUB & PHY (IC604). The signal line may be loosely connected. E
LAN-HUB & PHY Correct it if it is.
6 ————— ————— If the symptom persists after the above Replace the LAN-HUB & PHY (IC604). —————
corrections.
CDJ-2000NXS2 27
5 6 7 8
1 2 3 4
28 CDJ-2000NXS2
1 2 3 4
5 6 7 8
6 Loose connection MAIN Assy Check the connection between the MAIN Check the connections between MAIN CPU —————
between the MAIN CPU (IC10) and SDRAM (IC1, IC2). (IC10) and DDR2 (IC1, IC2).
CPU and SDRAM The signal line may be loosely connected.
Correct it if it is.
7 ————— ————— If the symptom persists after the above Replace the MAIN Assy. —————
corrections.
CDJ-2000NXS2 29
5 6 7 8
1 2 3 4
A
1 6
RF (CD: STD-905/DVD: Z-1) Pause (CD/DVD) 1-ch TE, 2-ch TEDRV, 3-ch RF, 4-ch OFTR
B
2 7
Loading in (1-ch LPS1, Loading out (1-ch LPS1, Track search (CD/DVD)
2-ch LPS2, 3-ch LOAD) 2-ch LPS2, 3-ch LOAD) 1-ch TE, 2-ch TEDRV, 3-ch SLIN1, 4-ch SLIN2
C
3 8
In-focus (CD/DVD) 1-ch FE, 2-ch FEDRV Search (CD-DA/DVD-MP3)
1-ch TE, 2-ch TEDRV, 3-ch SLIN1, 4-ch SLIN2
D
4 9
Setup (CD/DVD) 1-ch FE, 2-ch FEDRV, 3-ch TE, 4-ch SPIN Stop (CD/DVD)
1-ch FE, 2-ch FEDRV, 3-ch SPIN, 4-ch SPDLFG
E
5
Playback (CD/DVD) 1-ch FE, 2-ch TE, 3-ch SLIN1, 4-ch SLIN2
30 CDJ-2000NXS2
1 2 3 4
5 6 7 8
A
[1. USB B connector]
Whether communication between the PC connected via the USB B connector and this unit is properly performed or not can
be confirmed on the PC.
Note: Installation of the driver software is not necessary.
In a case of Windows 7:
Click on "Start" then right-click on "Computer." Next, select "Properties" then select "Device Manager" on the System
B
screen.
If a User Account Control screen is displayed, click on [Yes].
Devices to be added:
Universal Serial Bus controllers
USB Composite Device
Under “Sound, video and game controllers”
USB Audio Device
Human Interface Devices
HID-compliant device
USB Human Interface Device
[2. LINK]
Whether communication between the PC connected via the LINK connector and this unit is properly performed or not
can be confirmed on this unit.
Note: Use a Category 5 cable or a cable with higher specifications for connection.
Either a straight or cross LAN cable can be used when the unit is directly connected with the PC, but when the unit is
connected with the PC via a hub, be sure to use a straight cable.
CDJ-2000NXS2 31
5 6 7 8
1 2 3 4
6. SERVICE MODE
6.1 SERVICE MODE
A OUTLINE OF THE SERVICE MODE
D
DETAILS OF THE SERVICE MODE
Caution: When you turn the TOUCH/BRAKE knob to the far right in this mode, "Check mode of the load of Jog dial" will start.
(Refer to the following clause. )
32 CDJ-2000NXS2
1 2 3 4
5 6 7 8
CDJ-2000NXS2 33
5 6 7 8
1 2 3 4
B
3
1
5
2
All-blue screen
34 CDJ-2000NXS2
1 2 3 4
5 6 7 8
When the Jog dial is rotated swiftly in this mode, the speed is measured.
Either direction, clockwise or counterclockwise, is OK.
The meaning of the numerical value displayed is as follows.
TOP SPEED : Maximum speed given that normal speed is defined as when one rotation takes 1.8 sec.
TIME : Time required for the jog dial to slow down from 3x speed to 1.5x speed.
To measure the time required for slowdown, the maximum speed must be 7 times normal speed or higher.
B
If the maximum speed does not reach 7.0 times normal speed, the time indication section (00M:00S 00.0F) flashes as a warning.
When the measurement is carried out several times in a row, time will be displayed as an avarage of maximum 99 times of the
measurement.
This evens out the measurement value.
The result when measured twice.
D
The result when measured 10 times.
CDJ-2000NXS2 35
5 6 7 8
1 2 3 4
1 Version information
The version number of CPU/microcomputer carried in this machine is displayed.
The MAC Address of Ethernet built in this unit, destination code (DESTINATION)
and serial number (SN) are also displayed.
2 Error history
The 16 error codes recorded in the past are divided into two screens and displayed.
(1) is the latest error code.
The latest 16 error codes are displayed in reverse chronological order.
The screen is switched using the BACK button or TAG TRACK button.
C The item which follows an error code expresses its media.
(The error which is not related to media is blank.)
36 CDJ-2000NXS2
1 2 3 4
5 6 7 8
4 Factory reset A
It is used to reset the setting of UTILITY to the factory setting, or clear an error history.
If TIME MODE button is pressed on this screen, it resets to the factory setting below.
[UTILITY] Settings Other settings
PLAY MODE = CONTINUE TIME MODE = REMAIN
EJECT / LOAD LOCK = UNLOCK AUTO CUE = OFF
QUANTIZE BEAT VALUE = 1Beat JOG MODE = CDJ
HOT CUE AUTO LOAD = rekordbox SETTING MASTER TEMPO = OFF
HOT CUE COLOR = OFF QUANTIZE = ON
AUTO CUE LEVEL = MEMORY PHASE METER = TYPE1
SLIP FLASHING = ON
ON AIR DISPLAY = ON Error history
JOG BRIGHTNESS = 2 ALL CLEAR
JOG INDICATOR = ON B
DISC SLOT ILLUMINATION = 2
LANGUAGE = <Shipment setting >
HISTORY NAME = "HISTORY"
PLAYER No. = AUTO
MIDI CHANNEL = 1
DIGITAL OUT 24bit
AUTO STANDBY = ON
LCD BRIGHTNESS = 3
SCREEN SAVER = ON
DUPLICATION = DEFAULT
Factory reset can be performed if you turn the power on while pressing the
USB-STOP button and the EJECT button at the same time.
However, the error history is not cleared at this time.
C
5 Drive Self-Diagnosis
Self-diagnosis of a drive is performed.
Please refer to
"[5] Drive self-diagnosis" and
"[6] Contents of drive self-diagnosis"
for details.
CDJ-2000NXS2 37
5 6 7 8
1 2 3 4
To recover from auto standby mode, trigger any operation except the following:
performed,
• Press the USB STOP button
• Jog rotation (except for touching the Table top)
• Turn the TOUCH/BREAK , RELEASE/START volume
• Move the TEMPO slider
• Switch the DIRECTION lever
Auto standby mode will be reset.
C
Since auto standby reset is the same processing as turning the power on,
the service mode will be ended.
38 CDJ-2000NXS2
1 2 3 4
5 6 7 8
A
[4] List of displayed error
WAVE display shows "E-XXXX: DISC DRIVE ERROR".
Note: An alarm port is a function to notify the location of abnormality based on the number of pulses generated from the SH test port.
Error Alarm port
Display word Contents Notes
code correspondence
E-7001 DISC DRIVE ERROR The ATAPI drive doesn't function normally. _
E-7021 PHY CHIP ERROR The PHY CHIP does not function _ B
E-7022 PANEL CPU ERROR The PANEL CPU does not This error code appears when communication _
function normally. between the PANEL CPU and the MAIN CPU
is not established due to wire connection error,
etc. The error code also appears when
firmware update of the PANEL CPU fails.
The MAIN CPU detects the error and sends
the error code to GUI.
E-7023 GUI CPU ERROR The GUI CPU doesn't function This error code appears when the GUI _
normally. firmware update fails. The GUI CPU is
activated in the emergency mode and displays
the error code.
* If the GUI CPU cannot be activated even in
the emergency mode, nothing will be displayed. C
E-7024 MAIN CPU ERROR The MAIN CPU does not function This error code appears when the MAIN CPU
normally. firmware update fails. The MAIN CPU detects
the error and sends the error code to GUI in
the emergency mode.
E-7026 AUTH CHIP ERROR Apple authentication chip does not _
work normally.
E-7101 INTERRUPT EXCEPTION Unexpected abnormalities on the
MIAN CPU occurred.
E-7201 CANNOT READ DISC TOC Data can't be read.
E-8301 CANNOT READ DISC Abnormalities occurred during starting.
D
E-8302 CANNOT PLAY TRACK Abnormalities occurred during playback.
E-8303 CANNOT PLAY TRACK Error occurred when writing in buffer memory.
E-8304 UNSUPPORTED FILE FORMAT Decoding error occurred.
E-8305 UNSUPPORTED FILE FORMAT This format is not supported.
E-8306 NO FILE An unsupported USB device is connected.
E-8307 • DEVICE NO RESPONSE • There is no response from the connected • USB ACCESS ERROR
• UNSUPPORTED DEVICE device. • An unsupported USB device is connected.
• HUBS ARE NOT SUPPORTED • An unsupported device is connected.
• Unsupported hubs are connected. One of these three error types is indicated.
E-8308 SD CARD ACCESS ERROR MMC (Multi Media Card) was connected.
E
E-8309 LINK ACCESS ERROR Link access failed after 4 consecutive
timeout errors.
E-8709 COMMUNICATION ERROR GUI CPU and MAIN CPU cannot be When the communication with MAIN is not
communicated. materialized by the abnormalities of connection,
GUI displays an error code spontaneously.
When MAIN does not operate completely, it will
be in this mode.
E-9101 MECHANICAL TIMEOUT Mechanism operation was not
completed within regulation time.
CDJ-2000NXS2 39
5 6 7 8
1 2 3 4
A
[5] Drive self-diagnosis
Drive self-diagnosis is performed in the following three steps.
[Push PLAY Button] is displayed at the beginning of each step. Insert the test disc and press the PLAY button.
Step 1. A flashing message [Executing ...] is displayed and the diagnosis starts.
Step 2. When the diagnosis is successfully completed, [Complete] is displayed and the disc is automatically ejected.
Step 3. If the diagnosis is disabled for some reason, the following message is displayed and the disc is automatically ejected.
[Mecha Error] Mechanism error occurred such as a loading mechanism error.
[Setup Error] The disc was not started.
[Error Stop] An error occurred in the middle of the diagnosis and the diagnosis stopped.
[Check Disc] The disc differs from the disignated disc.
[No Disc] No disc is inserted.
B
The following items are diagnosed.
See "[6] Contents of drive self-diagnosis" for the details of each item.
CD-LD LIFE CHECK
DVD-LD LIFE CHECK
STEPPER CHECK
OEIC CHECK
DISC MOTOR CHECK
CD ERROR RATE CHECK
Result display
The result of the diagnosis of each item is displayed as "OK" or "NG". Undiagnosed item is displayed as "--."
As for "CD-LD Life Check" and "DVD-LD Life Check",
the working time of the LD is displayed when it exceeded the predetermined
period of time (7000H).
("OK" is displayed when it is not exceeded 7000H, and the working time is
E not displayed.)
40 CDJ-2000NXS2
1 2 3 4
5 6 7 8
STEP 1 STEP 2
(1) CD-LD LIFE CHECK (7) DVD ERROR RATE CHECK
This checks the cumulative working time of the LD to An error rate is measured and the final check is
judge degradation status. performed.
[NG] will be displayed if the working time exceeds 7000H.
LD current should be measured when the working time STEP 3
exceeds 7000H since the failure date is 1 %.
(8) USER CD PHYSICAL CHECK
(2) DVD-LD LIFE CHECK Distinguishes whether the cause of the error is due to
D
Same as mentioned above. the disc or not when the user submitted a disc.
Checks the characteristic of the disc based on
automatic adjustment value.
(3) STEPPER CHECK
Only CDs are accepted. (Judged based on precedents)
Detects malfunction of the stepper motor caused by
foreign materials/stuck, defect of inside switch, step loss
due to mechanical component defect, lack of lateral (9) USER CD SCRATCH CHECK
pressure, The error rate of the entire disc is measured per
Ensures that the stepper motor works correctly using the 1 minute, and best value and worst value are calculated.
inside switch. The state of the disc is checked from those values.
CDJ-2000NXS2 41
5 6 7 8
1 2 3 4
In the case of DVD, whenever the FWD/REV is pressed, the search starts with the following direction and pauses.
When the FWD direction was pressed when a DUAL LAYER DISC is in the deck.
→ L0 inside → L0 middle → L0 outside → L1 inside → L1 middle → L1 outside →
When the REV direction was pressed when a DUAL LAYER DISC is in the deck.
← L0 inside ← L0 middle ← L0 outside ← L1 inside ← L1 middle ← L1 outside ←
When the FWD direction was pressed when a SINGLE LAYER DISC is in the deck.
→ L0 inside → L0 middle → L0 outside →
F When the REV direction was pressed when a SINGLE LAYER DISC is in the deck.
← L0 inside ← L0 middle ← L0 outside ←
42 CDJ-2000NXS2
1 2 3 4
5 6 7 8
The following messages are displayed in the drive condition indication section. A
*: The search address [IN/MID/OUT] is relative depending on the total capacity of the disc.
*: The search location of [OUT] is about 20000 sectors from the outermost address on the disc.
CDJ-2000NXS2 43
5 6 7 8
1 2 3 4
A Step command
A series of operations for the set-up will be carried out step by step.
If the CUE/LOOP CALL NEXT (d) button is pressed, the procedure will step up (even if the PREV (c) button is pressed,
the step down will not occur.) Operation and display of each step are as follows.
44 CDJ-2000NXS2
1 2 3 4
[8] Alarm port output
In addition to "[3] Various displayed information"_"3 Auto device diagnosis" the test port output on the main board can identify
abnormalities of each device when the power of the device is turned on and initialized.
If a failure is detected in the device when the power is on, the alarm port will output the pulse signal as follows:
Alarm Port Service Mode/Auto Device Diagnostic Display Normal
Error
Detection Remarks Output Pattern Display Remarks Display
5
5
MAIN CPU
FLASH (for MAIN CPU) × If FLASH fails, the boot program will not work. × ←
SDRAM (for MAIN CPU) _ (0.5sHI->0.5sLOW) x 1 time -> 2sLOW -> × If SDRAM fails, the service program does
the same pattern to be repeated not work.
Peripheral with built-in MAIN CPU
IDE (DRIVE) _ (0.5sHI->0.5sLOW) x 7 times -> 2sLOW -> _ E-7001
the same pattern to be repeated
USB-A ⎯ Since it is SH built-in, it is quite unlikely to have an ⎯ ←
SD ⎯ issue only in a peripheral device. ⎯
Whether any issue occurs all the way to connectors
LAN ⎯ or not may not be detected. ⎯
External peripheral
USB-B _ (0.5sHI->0.5sLOW) x 4 times -> 2sLOW -> _ E-7020
6
6
7
7
GUI CPU (GUI) _ (0.5sHI->0.5sLOW) x 6 times -> 2sLOW -> " Although detection is possible even when
the same pattern to be repeated communication fails, precise testing may
not be performed because it is unable to
display on the LCD.
FLASH (for GUI CPU) × If FLASH is NG, the boot program itself does not operate. × ←
SDRAM (for GUI CPU) × If SDRAM fails, it cannot communicate with MAIN CPU. × ←
External peripheral communicated with PANEL CPU
CDC _ (0.5sHI->0.5sLOW) x 8 times -> 2sLOW -> _ E-7025
the same pattern to be repeated
Everything normal After 2sHI, remain in LOW
8
8
45
A
1 2 3 4
2 Turn on the power while pressing both of the MEDIA SELECT/USB button and the RELOOP button.
(Please continue pressing until "Pioneer LOGO"screen disappears.)
Insert a USB memory stick in the USB port when the message "Connect USB storage device into USB port." appears.
C (If the service mode is activated when a USB memory stick is inserted, the message will not be displayed and the update
will start immediately.)
3 Update is automatically performed in the order of "GUI -> Drive -> MAIN -> PANEL".
The update status is displayed showing the progress bar indicator and the percentage. Previous version is displayed as
well as the new version.
4 If there is no file, the device will be grayed out and the update will not be performed.
Please note that the progress bar indication and percentage shown on the screen are just an estimate.
5 When the update is completed, the message "Firmware update is completed. Turn the power off before using" will appear.
Please power off and then power on again.
46 CDJ-2000NXS2
1 2 3 4
5 6 7 8
D
6.2 ABOUT THE DEVICE
Device Name Function Part No. Ref No. Assy
MAIN CPU Main control R8A77240D500BG2 IC10 MAIN Assy
FLASH Memory for MAIN CPU (Firmware) DYW**** (NSP) IC12 MAIN Assy
DDR2 Memory for MAIN CPU (Work) W971GG6SB-25 IC1, IC2 MAIN Assy
DSP Audio DSP TMS320C6655CZH IC301 MAIN Assy
DDR3 Memory for DSP (Work) W631GG6KB-12 IC501, IC502 MAIN Assy
USB-HUB USB-HUB (function) USB2512B-AEZG-TR IC603 MAIN Assy
USB-LAN Conversion CONTROLLER for USB-B (function) RTL8152B-VB-CG (NSP) IC602 MAIN Assy
E
LAN-HUB & PHY LAN-HUB included PHY RTL8304E-CG IC604 MAIN Assy
AUTHENTICATION CHIP Apple authentication H337S3959 IC14 MAIN Assy
FPGA SPDIF_TX and I/O level conversion XC3S50A-4FTG256C IC1201 MAIN Assy
GUI CPU LCD display control R5S72690RW266FP IC4604 LCDB Assy
FLASH Memory for GUI CPU (Firmware) DYW**** IC4602 LCDB Assy
SDRAM Memory for GUI CPU (Work) M12L2561616A-5TG2S IC4601, IC4603 LCDB Assy
PANEL CPU Button input, LED & Jog FL control DYW**** IC8001 PNLB Assy
SODC Disc drive control MN103S71F IC7006 SRVB Assy
FLASH Memory for DRIVE CONTROLLER DYW**** IC7004 SRVB Assy
Note on DYW****
The "****" part of the part number changes each time the firmware is updated. F
Two or more FLASH and SDRAM are mounted in the main body.
Please diagnose it after confiming whether it is a device that agrees with purpose again.
CDJ-2000NXS2 47
5 6 7 8
1 2 3 4
7. DISASSEMBLY
A Note:
(1) Do NOT look directly into the pickup lens. The laser beam may cause eye injury.
(2) Even if the unit shown in the photos and illustrations in this manual may differ from your product, the
procedures described here are common.
1 1
2
2
2 1
1 2 Front • Bottom view
C
4 4
Diagnosis
E
SRVB
Assy
F
Front • Bottom view
48 CDJ-2000NXS2
1 2 3 4
5 6 7 8
1
2
5
2
2 2 C
Front • Bottom view
3
D
E
[2] MAIN Assy
(1) Remove the SD earth spring, by removing SD earth spring Shield plate
the 1 screw.
(BPZ30P080FNI)
CDJ-2000NXS2 49
5 6 7 8
1 2 3 4
2 1
3
B 2 2
(8) Disconnect the Power switch from the shaft. MAIN Assy
(9) Stand the MAIN Assy with the USBA and USBA Assy 9
SDCB Assemblies.
E SDCB Assy
Diagnosis
Shaft
8
Power switch
F
50 CDJ-2000NXS2
1 2 3 4
5 6 7 8
Notes on Reassembly A
Cushion B
(Wrap the cushion around
the shield plate one round.)
• How to dress the cables between the MAIN and SDCB Assys and between the MAIN and USBA Assys
Cord clamper D
After clamping the FFC, bend the end
of the cord clamp at a right angle at a
Ferrite core
position approximately 5 mm away from
the end so that it will not come into
contact with the Shielded Conn-Cable.
• How to dress the cables from the AC inlet and the SW POWER SUPPLY Assy
CN1
The cables from the AC inlet
must be placed at a level lower Pull the cables
than the insulator-mold line. so that they will
not protrude
Insulator-mold upward.
CN2
CDJ-2000NXS2 51
5 6 7 8
1 2 3 4
1 2 1 2
Guide
B 2
1
SW POWER SUPPLY Assy
• Bottom view
Plate Stay
The other screws are random order. Stay
1 2
C
Plate
D
1 1
1 1
E
F
This boss is not installation position.
52 CDJ-2000NXS2
1 2 3 4
5 6 7 8
1 1
1 3 B
TM Assy-S
[1] Float Base Section
(1) solder the short-circuit point. (short)
Pickup
Note:
After working, connect the flexible cable,
then remove the soldered joint (open). 1
D
for DVD
for CD
• Rear view
CDJ-2000NXS2 53
5 6 7 8
1 2 3 4
CN7003
CN7004 2
2
B
CN7001 CN7009
2 2
• Bottom view
C
3 3
3 3
54 CDJ-2000NXS2
1 2 3 4
5 6 7 8
4 5 4 5
4
C
Projection (large)
to the rear
6
F
Damper
CDJ-2000NXS2 55
5 6 7 8
1 2 3 4
[2] TM Assy-S
(1) Remove the 3 float screws. SPCN Assy
(DBA1286)
(2) Remove the TM Assy-S. 3
C
(3) Remove the 1 screw. 4
(IPZ20P060FTC) 4
5
(4) Unhook the 2 hooks. 1
(5) Remove the SPCN Assy.
2 1
TM Assy-S
1
D
Front
Pickup lens
56 CDJ-2000NXS2
1 2 3 4
5 6 7 8
C
(2) Disconnect the 2 flexible cables.
(CN6303, 8501)
(3) Remove the 6 screws.
(BPZ30P080FNI)
(4) Remove it while pulling Jog dial Section in
front side.
3 3
Screw tightening order
4 5
3 6 3 3
D
CN6303
3
1 2 3 2 CN8501
• Bottom view
CDJ-2000NXS2 57
5 6 7 8
1 2 3 4
A
(5) Unhook the 3 hooks.
(6) Remove the Jog Section.
6
Jog Section
C 5
Note:
Be careful not to lost SW spring.
E
SW spring
58 CDJ-2000NXS2
1 2 3 4
5 6 7 8
A
Notes on replacing the Sheet SW
Styling of the Sheet SW
Bend it to the direction Sheet SW
of the arrow.
Holder
CDJ-2000NXS2 59
5 6 7 8
1 2 3 4
A
Alignment of the Rack Plate
Place the rack plate so that its teeth are
engaged with those of the gears and its
triangular marks are positioned as shown Dial gear Link gear B
in the figure.
C Reference information
Screw tightening order (JFLB Assy) Screw tightening order (Link plate)
The other screws are random order. The other screws are random order.
1 2
2 1
60 CDJ-2000NXS2
1 2 3 4
5 6 7 8
1
Knob/SLD
C
• Sheet/FFC
(1) Remove the Sheet/FFC, by removing the
1 rivet.
Sheet/FFC
• Bottom view
• Sheet
(1) Remove the 3 screws. Sheet Sheet 1 ×3
(BPZ30P080FNI)
Front
• Bottom view
F
CDJ-2000NXS2 61
5 6 7 8
1 2 3 4
B
2 1
1 Front
• Bottom view
• HLED Assy
(1) Disconnect the 2 flexible cables. Sheet HLED Assy
(CN6301, 6303) 4 ×8
(2) Remove the 2 screws.
3
Leaf spring 3
(BBZ30P060FTB)
(3) Remove the Sheet and Leaf springs, by CN6303
1 2
• SLDB Assy
E
(1) Remove the Plate, by removing the 4 screws.
(BPZ30P080FNI) 1 ×4
1 Front
Plate
2
• Bottom view
62 CDJ-2000NXS2
1 2 3 4
5 6 7 8
3 Front
SLDB Assy
2 • Bottom view
1
PNLB Assy
Screw tightening order C
3
4
• Bottom view
1 2
D
SLDB Assy
CDJ-2000NXS2 63
5 6 7 8
1 2 3 4
A Reference information
Screw tightening order (Lens) Screw tightening order (Base)
1
1 2
Base
Lens 2
• Bottom view • Bottom view
8 6
C
7 5
• Bottom view
3 4
2 1
• Exterior Section
(1) Remove the Dial knob. 1
Dial knob
D
E
(2) Remove the Cover, by removing the 2 screws. 3 ×6
(BBZ26P060FTB) 2 2 Cover
(3) Remove the Shield case, by removing the
6 screws.
(BBZ26P060FTB)
Shield case
F • Bottom view
64 CDJ-2000NXS2
1 2 3 4
5 6 7 8
• LCDB Assy A
(1) Disconnect the 2 flexible cables and 2 ×10
1 connector. 1
(CN4401, 4801,4802)
1
(2) Remove the LCDB Assy, by removing the CN4401 LCDB Assy
CN4802
10 screws.
(BPZ26P080FTC)
• Stay
(1) Remove the Stay, by removing the 4 screws. 1 ×4
(BPZ26P080FTC)
C
Screw tightening order
The other screws are random order.
Stay
1 2
• Bottom view
D
• TFT LCD and Touch panel
(1) Remove the TFT LCD.
(2) Remove the Panel/TCP.
(3) Remove the Spacer/LCD.
TFT LCD
(4) Remove the Touch panel.
(5) Remove the Plate/GND.
1
Panel/TCP
4
Plate/GND
CDJ-2000NXS2 65
5 6 7 8
1 2 3 4
• MAIN Assy • Input Drive LD life before the replacing with a manual.
(See "6.1 SERVICE MODE")
• Confirmation of the version of the firmware
• Updating to the latest version of the firmware
• LCDB Assy (FLASH ROM: IC4602) • Confirmation of the version of the firmware
• Updating to the latest version of the firmware
B • PNLB Assy (PANEL CPU: IC8001) • Confirmation of the version of the firmware
• Updating to the latest version of the firmware
• SRVB Assy (FLASH ROM: IC7004) • Confirmation of the version of the firmware
• Updating to the latest version of the firmware
• Tempo slider VR: VR8702 (SLDB Assy) • TEMPO ZERO POINT ADJUSTMENT
(See "8.5 TEMPO ZERO POINT ADJUSTMENT")
C
• Jog dial section component • JOG DIAL ROTATION LOAD ADJUSTMENT
(See "8.4 JOG DIAL ROTATION LOAD ADJUSTMENT")
∗: For confirmation of the touch display operation, refer to "Confirmation of the Touch display operation" in "[1] Check mode of
the buttons and displays" of "6.1 SERVICE MODE."
66 CDJ-2000NXS2
1 2 3 4
5 6 7 8
Writing the serial number can be performed from a PC that is connected with this unit via a USB B cable. A
Preparations
1 Download the software for writing the serial number (GGS1177) from Niis.
2 Unzip GGS1177 then store the two unzipped files (mmpforseigi.exe and hidcom.dll) in the PC.
Create a new folder at a place of your preference, such as the desktop, to store those files.
Procedure
1 Connect the unit with a PC via a USB B cable. 5 Enter an "xSN" ("x" denotes a 12-digit serial number printed
2 Start the writing software, by double-clicking on mmpforseigi.exe. on the label) command then click on OK.
3 Enter a "$CDJ" command then click on OK.
CDJ-2000NXS2 67
5 6 7 8
1 2 3 4
A
JOG Check Mode : ON
• It is the mode which judges the load (light/-- heavy) numerically when rotating the Jog dial.
POWER OFF
[Measuring method]
C 1. The adjustment value of adjust plate is adjusted to "0" (Refer to Fig. 2).
2. Enters the mode for checking the load on the Jog dial.
3. The jog dial is mightly rotated. Moreover, the direction of the rotation is clockwise.
4. The rotation speed and time are displayed in LCD display (Refer to Fig. 1).
The time required so that the rotation may decrease from 3 X speed to 1.5 X speed when maximum speed is only
7 X speed or more is displayed.
The average of the rotation decrease time of 5 times in all is confirmed in spec or less.
Spec: 170 ± 20 msec.
5. When the rotation decreace time is coming off from spec, the adjustment value of adjust plate is changed, and it does
from 2 of above-mentioned to 4.
D
Adjust plate
To decrease
the load
68 CDJ-2000NXS2
1 2 3 4
5 6 7 8
Jigs
B
1 Insert the insulation sheet between SLDB Assy and the 3 Adjust it so that turn VR8702, and the voltage of the
main unit. digital multimeter becomes 0 ± 5 mV.
SLDB Assy
0 ± 5 mV D
J8705
1 J8706
V+3R3E
Pin 4: ADCT
J8710
Pin 5: ADIN
CN8701
J8708
9
J8709
GNDD J8711
V+5
Insulation sheet
J8703
J8707
J8702
S8701
1 /4
D8701
TEMPO 0 E
RESET
SLDB
CENTER POSITION.
Knob section of slide VR
ADJ
DWX3705-
J8704
VR8702
VR8702
(Zero Poin ADJ)
C8702
VR8701 F
CENTER POSITION
SIDE A
SLDB ASSY
CDJ-2000NXS2 69
5 6 7 8
1 2 3 4
70 CDJ-2000NXS2
1 2 3 4
5 6 7 8
- For the applying amount of lubricants or glue, follow the instructions in this manual.
FLXJ only
B
or or or
SYXJ only
AXJ5 only
F
Front
• Bottom view
CDJ-2000NXS2 71
5 6 7 8
1 2 3 4
9 Operating Instructions (Quick Start Guide)(Zhcn) Not used Not used Not used DRH1324
NSP 10 Leaflet DRH1275 DRH1275 DRH1275 DRH1274
14 Packing Case DHG3438 DHG3440 DHG3441 DHG3443
D NSP 16 Warranty ARY7158 Not used Not used Not used
17 Caution Card SB Not used Not used ARM7064 Not used
72 CDJ-2000NXS2
1 2 3 4
9.2 EXTERIOR SECTION
• Bottom view
Refer to
"9.3 CONTROL PANEL SECTION".
5
5
G
G
a F
E
F
F
E
D D
b
b E
6
6
2 C
H 2
I 1
I
2 1
L H
A C
CDJ-2000NXS2
A
2
2
J
M
Refer to
SLMB
CN9001
"9.6 SLOTIN MECHA SECTION". Q
1
J
2
K
Stteping
SPCN motor
1 1
7
M
7
L
Pickup
K
1 B
1
2 I
H 1
J
1
I
2
1
H
2 M
L
a
2
K 1
2 1 L
2 J K
M
8
8
NON-CONTACT
CONTACT SIDE
SIDE
73
A
1 2 3 4
B 56 Screw BPZ30P100FTC
11 Crimp Connector DDC1024
12 Connector Assy PF06PP-S10 57 Screw IBZ30P100FTB
13 Ferrite Core BTX1037 58 Screw PMB30P080FTB
14 Power Knob DAC2306 59 Screw PMH30P080FTC
15 SD Earth Spring DBK1357 60 Screw PMH40P080FTC
21 Bracket/ACI DNH3020
22 Stay/KST DNH3021
23 Stay DNH3225
24 Stay DNH3226
25 Stay DNH3227
41 Cushion DEC3688
42 Gasket/JOG DEC3562
43 Damper CNV7618
44 Earth Spring DBH1398
45 Float Spring (G5) DBH1494
74 CDJ-2000NXS2
1 2 3 4
9.3 CONTROL PANEL SECTION
• Bottom view
Refer to
"9.4 JOG DIAL SECTION".
5
5
1/2
D
B E
C
Refer to
"9.5 DISPLAY SECTION".
N F H
G
MAIN
J
6
CN1701
6
H
I
2
E A B 2/2
M 1/4
CDJ-2000NXS2
1 C
D A
2
4/4
A
1
A
2/4
3/4
O
2/2
1/2
7
7
1/2
2/2
8
8
VINYL
REV
CDJ
2/2
3/4 or 2/4
NON-CONTACT
CONTACT SIDE
• Top view
4/4
SIDE
75
A
1 2 3 4
B 56 Base DNK6470
11 FFC DDD1712
12 Panel DAH3051 57 Lens DNK6491
13 Plate DNH3223 58 Lens DNK6492
14 Sheet/FFC DEC3577 59 Lens DNK6493
15 Knob DAA1303 > 60 Control Panel DNK6494
31 Button DAC3148
32 Button DAC3149
33 Slide Sheet 1C DAH2404
34 Lever Spring DBH1702
35 Spring DBH1717
76 CDJ-2000NXS2
1 2 3 4
5 6 7 8
A
Holder
Lubricating oil
(GYA1001)
Lubricating oil C
(GEM1034)
Lubricating oil
(GEM1034)
D
Lubricating oil
Lubricating oil (GEM1034)
(GEM1034)
KSWB
CN8501
P
E
HLED Lubricating oil
CN6303 (GYA1001)
Lubricating oil
K (GYA1001)
A B
NON-CONTACT
CONTACT SIDE
F
SIDE
CDJ-2000NXS2 77
5 6 7 8
1 2 3 4
B
11 Link Plate DNH2848
12 Jog B DNK4068
13 SW Ring DNK5233
14 Gear/LD DNK6145
15 Smoother DNK5237
16 Holder DNK6556
17 Comp Plate DNK5243
18 Adjust Plate DNK5300
19 Cam Plate DNK5301
C
20 Dial Gear DNK5302
26 Roller DXB2178
27 Stay Assy/JOG DXB2133
28 Encoder Spring DBH1710
D 29 Plate DEC3700
30 Gear/A DNK6143
31 Gear/B DNK6144
32 Leaf Spring/ADJ DBK1376
33 • • • • •
34 • • • • •
35 • • • • •
36 • • • • •
37 Screw (FE) DBA1265
E 38 Screw BPZ20P100FTC
39 Screw BPZ30P080FNI
40 Screw IPZ20P060FTC
78 CDJ-2000NXS2
1 2 3 4
5 6 7 8
• Bottom view A
NON-CONTACT
CONTACT SIDE
SIDE
PNLB
CN8002
PNLB
CN8001
H
HLED
B
CN6301
MAIN
CN1701
A
C
A
CDJ-2000NXS2 79
5 6 7 8
1 2 3 4
6 Button DAC3113
7 Button DAC3114
8 Button DAC3115
9 Button DAC3116
10 Button DAC3117
B
11 Button DAC3118
12 Panel/TCP DAH3006
13 Panel DAH3043
14 Panel DAH3044
15 Packing/LCD DEC3565
16 Packing/L DEC3568
17 Packing/S DEC3569
18 Spacer/LCD DEC3571
19 Light-D Sheet DEC3613
C
20 Plate/GND DNH3173
26 Lens DNK6468
27 • • • • •
28 • • • • •
D 29 Screw BBZ26P060FTB
30 Screw BPZ26P080FTC
80 CDJ-2000NXS2
1 2 3 4
5 6 7 8
A
Lubricating oil
(GYA1001)
SRVB
CN7003
GRY
WHT
A
Lubricating oil
(GYA1001) D
B
Dyfree Dyfree
(GEM1036) (GEM1036)
A
GRY C
WHT
Lubricating oil
(GYA1001)
SRVB
CN7001
SRVB Note:
CN7004 The TM Assy 09SD-S is supplied only in
assembly form, not as a single parts.
B SRVB
CN7009
C
E
NON-CONTACT
CONTACT SIDE
F
SIDE
CDJ-2000NXS2 81
5 6 7 8
1 2 3 4
6 FFC DDD1704
7 FFC DDD1713
8 Connector Assy 2P DKP3769
9 Connector Assy PF05PP-C25
10 DC Motor Assy-S DXX2510
B
NSP 11 DC Motor S DXM1230
NSP 12 Worm Gear DNK3910
13 Clamp Spring DBH1374
14 Guide Spring DBH1375
15 SW. Lever Spacer (PET) DEC2420
21 Lever BP DNK3836
22 Loading Gear DNK3911
23 Drive Gear DNK3912
24 Clamper Assy DXA2043
25 Loading Lever Assy DXB1880
82 CDJ-2000NXS2
1 2 3 4
SEARCH LINK INFO UTILITY
rekordbox
BROWSE TAG LIST INFO MENU
TAG TRACK
BACK / REMOVE STANDBY
USB
STOP LINK
DISC EJECT
USB
SD
DISC
SD
TIME
VINYL
HOT CUE AUTO TRACK FILTER SHORT SPEED ADJUST
MODE CUE EDIT CUT
TOUCH / BRAKE
A E
QUANTIZE
B F RELEASE / START
C G
1/2X LOOP 2X
IN ADJUST OUT ADJUST
JOG ADJUST VINYL
4/ 8BEAT JOG
MODE
CDJ
D H
LOOP CUTTER
LIGHT HEAVY BEAT SYNC
SLIP
INST. DOUBLES
CALL/ DELETE
SYNC MASTER
BANK TEMPO
6 10 16 WIDE
DIRECTION
SLIP
REV
FWD
MASTER
REV TEMPO
TRACK SEARCH
SEARCH
CUE
TEMPO
RESET
ORDER NO.
RRV4646
REV FWD
PLAY / PAUSE
TEMPO
MULTI PLAYER
CDJ-2000NXS2
CDJ-2000NXS2
MULTI PLAYER
CDJ-2000NXS2
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Remarks
This service manual should be used together with the following manual(s).
Model No. Order No. Remarks
CDJ-2000NXS2 RRV4645 BLOCK DIAGRAM, EXPLODED VIEWS AND PARTS LIST etc.
SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive
B
harm.
Health & Safety Code Section 25249.6 - Proposition 65
IMPORTANT
Laser Pickup specifications and Laser characteristics
THIS PIONEER APPARATUS CONTAINS
LASER OF CLASS 1. For DVD Wave length (typ) : 655 nm
SERVICING OPERATION OF THE APPARATUS Operation output : 3 mW CW, Class 1
S H O U L D B E D O N E B Y A S P E C I A L LY Maximum output : Class 1 (Under fault condition)
INSTRUCTED PERSON. For CD Wave length (typ) : 790 nm
Operation output : 4.5 mW CW, Class 1
Maximum output : Class 1 (Under fault condition)
C
LABEL CHECK
Bottom view
2 CDJ-2000NXS2
1 2 3 4
5 6 7 8
CONTENTS
SAFETY INFORMATION.......................................................................................................................................................... 2
10. SCHEMATIC DIAGRAM ...................................................................................................................................................... 4
10.1 OVERALL WIRING DIAGRAM ..................................................................................................................................... 4 A
10.2 SRVB ASSY.................................................................................................................................................................. 5
10.3 SPCN, INSW and SLMB ASSYS.................................................................................................................................. 6
10.4 MAIN ASSY (1/11)........................................................................................................................................................ 7
10.5 MAIN ASSY (2/11)........................................................................................................................................................ 8
10.6 MAIN ASSY (3/11)........................................................................................................................................................ 9
10.7 MAIN ASSY (4/11)...................................................................................................................................................... 10
10.8 MAIN ASSY (5/11)...................................................................................................................................................... 11
10.9 MAIN ASSY (6/11)...................................................................................................................................................... 12
10.10 MAIN ASSY (7/11).................................................................................................................................................... 13
10.11 MAIN ASSY (8/11).................................................................................................................................................... 14
10.12 MAIN ASSY (9/11).................................................................................................................................................... 15
10.13 MAIN ASSY (10/11).................................................................................................................................................. 16 B
10.14 MAIN ASSY (11/11).................................................................................................................................................. 17
10.15 USBA ASSY ............................................................................................................................................................. 18
10.16 SDCB ASSY ............................................................................................................................................................. 19
10.17 LCDB ASSY (1/5) ..................................................................................................................................................... 20
10.18 LCDB ASSY (2/5) ..................................................................................................................................................... 21
10.19 LCDB ASSY (3/5) ..................................................................................................................................................... 22
10.20 LCDB ASSY (4/5) ..................................................................................................................................................... 23
10.21 LCDB ASSY (5/5) ..................................................................................................................................................... 24
10.22 PNLB ASSY.............................................................................................................................................................. 25
10.23 HLED ASSY.............................................................................................................................................................. 26
10.24 JFLB ASSY............................................................................................................................................................... 27
C
10.25 JOGB, SLDB, EUPB, KSWB and INDB ASSYS....................................................................................................... 28
10.26 SW POWER SUPPLY ASSY .................................................................................................................................... 29
10.27 WAVEFORMS........................................................................................................................................................... 30
11. PCB CONNECTION DIAGRAM ........................................................................................................................................ 31
11.1 SRVB ASSY................................................................................................................................................................ 31
11.2 SPCN, INSW and SLMB ASSYS................................................................................................................................ 33
11.3 MAIN ASSY ................................................................................................................................................................ 34
11.4 USBA, SDCB and LCDB ASSYS ............................................................................................................................... 36
11.5 PNLB ASSY................................................................................................................................................................ 38
11.6 HLED ASSY................................................................................................................................................................ 40
11.7 JFLB, JOGB and SLDB ASSYS ................................................................................................................................. 41
11.8 EUPB, KSWB and INDB ASSYS ................................................................................................................................ 43 D
11.9 SW POWER SUPPLY ASSY ...................................................................................................................................... 44
12. PCB PARTS LIST .............................................................................................................................................................. 45
CDJ-2000NXS2 3
5 6 7 8
F
*HORIZONTAL
TFT-LCD MODULE (CWX4352-) CN4401
CKS6625-A
CN4801
BackLight
CKS4428-A
1 YT
Anode 1
TOUCH PANEL (DSX1130-)
2 XR
CN4601
DKN1445-A
Cathode 2 3 YB
1
NM
1
4 XL FOR DEBUG
1 V+3R3_CPU
*VERTICAL *VERTICAL 2 V+3R3_CPU USB CONNECTOR USB CONNECTOR
CN6301
VKN1418-A
CN4001
VKN1418-A
3 GNDD (A-TYPE) (B-TYPE)
4 GNDD
V+12 1 1 V+12 5 REST_ER
1
2 *HORIZONTAL RT2 RT1 SD CARD
V+12 2 V+12 6 CPU_TRST
CN4802
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
RT5
1
2
3
4
5
6
8
9
GNDD 3 GNDD
RT1
RT2
3 7 CPU_TDI
RT3 RT4
NC
GND
VGL
VCC
VGH
NC
V1
V2
V3
V4
V5
V6
V7
V8
V9
V10
NC
NC
DITH
VCOM
AVDD
AGND
GND
UPDN
VCC
SHLR
STBYB
RSTB
MODE
VSD
HSD
DE
DCLK
B7
B6
B5
B4
B3
B2
B1
B0
G7
G6
G5
G4
G3
G2
G1
G0
R7
R6
R5
R4
R3
R2
R1
R0
VCC
AVDD
AGND
4 CKS6646-A
GNDD 4 GNDD 8 CPU_TMS
ZIF
JA5101 JA502
4
SD_SW 5 5 SD_SW 9 CPU_TCK 12
SDCB ASSY
DDD1711- DKN1664-A
4
DKB1118-A SD_W
SD_ILM_G 6 6 SD_ILM_G 10
FFC CPU_TDO
USBA ASSY G
VBUS
D-
D+
GND
SD_ILM_R 7 (REVERSE FACE) 7 SD_ILM_R 11 CPU_MPMD 11
F
TER
SD_ILM_B 8 L=56mm 8 SD_ILM_B 12 CPU_AUDSYNC
GNDD
GNDD
9
10
Pitch=1.0mm 9
10
GNDD
GNDD
H H 1/5 - H 5/5 LCDB ASSY (DWX3693) 13
14
CPU_AUDATA3
CPU_TxD
(DWX3695) (DWX3694) CN5001
CKS5956-A
SD_DATA2
SD_DATA3
SD_DATA0
SD_DATA1
SD_CMD
SD_DET
USB_STOP 11 USB_STOP
SD_CL
11 15 CPU_RxD
GND2
GND
VDD
USB_DN_A
USB_DP_A
USB_DN_B
USB_DP_B
SD_DATA2
SD_DATA1
SD_DATA0
SD_DATA3
USB_ILM_G 12 12 USB_ILM_G
V+5_USB
V+5_USB
16 CPU_EMU_BRK
SD_CMD
SD_DET
SD_CLK
SD_WP
*HORIZONTAL *HORIZONTAL *VERTICAL
V+3R3
VBUS
GNDD
USB_ILM_R 13 13 USB_ILM_R
GND
GND
17 CPU_RST
GND
GND
GND
CN5102 CN5101 CN5002
8
S_LED_PWM
10
PNL_CNVSS
S_LED_RCK
USB_ILM_G
S_LED_SCK
USB_ILM_R
USB_ILM_B
14
PNL_BUSY
USB_ILM_B USB_ILM_B
SD_ILM_G
SD_ILM_R
SD_ILM_B
14
MAT_SEL4
18
EUP_CON
GNDD
S_LED_SI
AKM1291-A
PNL_RXD
PNL_SCK
VKN1414-A
PWR_SW
PNL_TXD
PNL_RST
V+12LED
V+12LED
AKM1293-A
TCP_XIN
TCP_YIN
ENC_SW
TCP_YV
TCP_XV
KYE5_B
V+3R3E
SD_SW
V+12FL
10
1
7
V+3R3
V+5R2
V+5R2
V+5R2
V+5R2
2
ENC_1
V_DET
ENC_2
GNDD
GNDD
GNDD
GNDD
GNDD
1
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
19 DSP_TMS
KEY2
KEY1
OUT2
OUT1
VKN1431-A VKN1431-A
20 DSP_TDI DDA1052- DDA1053-
*VERTICAL *VERTICAL
SHIELDED SHIELDED DDD1706-
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
21
9
1
9
DSP_TDO FFC(SAME FACE)
CONN-CABLE CONN-CABLE
CN4005 CN4004 22 DSP_TCK AWG #26/#28 AWG #26/#28 L=70mm
Pitch=1.0mm
DDD1707- L=85mm L=120mm
DDD1707- 23 DSP_EMU0
FFC(REVERSE FACE) FFC(REVERSE FACE) 24 DSP_TRST
SD_DATA3 10
2
5
1
9
L=60mm L=60mm
CN601 CN603 CN604
GNDD
GNDD
USB_DN_A
USB_DP_A
V_BUS_B
Pitch=1.0mm
GND
SD_WP
SD_DATA2
SD_DATA1
SD_DATA0
GNDD
SD_CLK
V+3R3
SD_CMD
SD_DET
GNDD
GNDD
Pitch=1.0mm
USB_DN_B
USB_DP_B
V+5_USB
V+5_USB
AKM1291-A AKM1278-A-TBB CKS6095-A
*HORIZONTAL
CN8002 CN8001 *VERTICAL *VERTICAL
S_LED_RCK 27
EUP_CON 26
PNL_CNVSS 25
PWR_SW 24
ENC_1 23
V_DET 22
ENC_2 21
S_LED_PWM 20
ENC_SW 19
S_LED_SCK 18
MAT_SEL4 17
S_LED_SI 16
OUT2 15
PNL_BUSY 14
OUT1 13
PNL_SCK 12
GNDD 11
PNL_TXD 10
9
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1
VKN1287-A VKN1287-A
GNDD
PNL_RXD
GNDD
GNDD
PNL_RST
GNDD
GNDD
GNDD
V+3R3E
*VERTICAL
CN4002
V+12FL
GNDD
GNDD
V+12LED
V+12LED
V+3R3
KYE5_B
SD_ILM_G
KYE2
SD_ILM_R
KYE1
USB_ILM_B
SD_SW
USB_ILM_R
SD_ILM_B
USB_ILM_G
TCP_YV
TCP_XIN
TCP_XV
TCP_YIN
V+5R2
V+5R2
V+5R2
V+5R2
GNDD
GNDD
GNDD
*HORIZONTAL *HORIZONTAL *HORIZONTAL CN1701
CN6304
VKN1431-A
CN8004 VKN1434-A CKS6025-A
*HORIZONTAL *HORIZONTAL
VKN1287-A *VERTICAL
CN605 LAN
V+5R2 27 1 V+5R2 GND 1 1
GNDD
DKN1445-A
NM
CONNECTOR
V+5R2 26 2 V+5R2 TCP_SCLK 2 2 TCP_SCLK
GNDD 25 3 GNDD TCP_SDA 3 3
TCP_SDA
V+3R3_CPU 1
JA601
GNDD 24 4 GNDD GND 4 4 V+3R3_CPU 2 VKN2023-A
I
GNDD
2
2
CUEA_B 23 5 CUEA_B SH2_RSPCK1 5 5 GNDD 3
SH2_RSPCK1
CUEA 22 6 CUEA SH2_SSL10 6 6 GNDD 4
SH2_SSL10
SH2_MOSI1 REST_ER
CUEA_R 21 7 CUEA_R
GND
7 7
SH2_MOSI1
CPU_TRST
5
JA901
CUEB 20 8 CUEB 8 8
GNDD 6 PKB1045-A
PNLB ASSY
CUEA_G 19 9 CUEA_G SH2_MISO1 9 9 CPU_TDI 7 1
SH2_MISO1
2 DIGITAL
HLED ASSY (DWX3700)
N
CUEB_B 17 11 CUEB_B PENIRQ CPU_TCK 3
O
11 11 9
PENIRQ
CUED 16
CUEB_G 15
CUEB_R 14
DDD1712-
FFC
(REVERSE FACE)
12
13
14
CUED
CUEB_G
CUEB_R
(DWX3702) JH8003 CN8651
GND
V+1R2
V+3R3
12
13
14
DDD1705-
12
13
14
GNDD
V+1R2
CPU_AUDSYNC
CPU_TDO
CPU_MPMD
10
11
12
CDJ-2000NXS2
E E 1/11 - E 11/11
V+3R3 CPU_AUDATA3
EUPB ASSY
CUEC_R 13 15 CUEC_R 15 (SAME FACE) 15 13
KSWB ASSY
Pitch=1.0mm V+3R3 DKB1121-A
CUEC_B 12 16 CUEC_B 52147-0810 51048-0800
KEY4_B 1 1 KEY4_B GND 16 L=180mm 16 CPU_AUDATA1 14
GNDD
Pitch=1.0mm 1
CUED_B 11 17 CUED_B GNDD V+12 17 17 CPU_AUDATA0 15 L
2 2
D_INDL 1 1 D_INDL GNDD V+12
2 AUDIO
(DWX3704)
JP8003 CPU_EMU_BRK
(DWX3703)
CUEC_G 10 18 CUEC_G MAT_SEL4 V+12 18 18 16
PLAY 2 2 PLAY 3
D20PDY0605E
3 MAT_SEL4
V+12 3 OUT
CUED_G 9 19 CUED_G V+5R2 JUMPER WIRE PNL_RST 19 19 CPU_RST 17 R
CUE 3 3 CUE 4 4 V+5R2 PNL_RST
L=50mm 4
SH2_RESET
V+12
PWR_SW 28 28
DDD1641- PWR_SW
GND FOR DEBUG (DSP&CPU)
FFC 29 29
GNDD S801
M
*VERTICAL *HORIZONTAL (SAME FACE) V+12_EUP 30 30 ASG1102-A
L=75mm JH8002 CN8701 V+12_EUP Only Proto
CN6302
VKN1425-A
CN8003
VKN1281-A Pitch=1.0mm 51048-0900 52151-0910
V+3R3E 1 1 V+3R3E
2
1
V+12LED 21 1 V+12LED
GNDS GNDS
CN6201 2 2
SLDB ASSY
V+12
GNDD
GNDD
D_INDIL
V+12FL 20 2 V+12FL
RKN1045-A KYE3_B 3 3 KYE3_B
GNDD 19 3 GNDD
ATA_RESET
ATA_DREQ
ADCT ADCT
ATA_DACK
4 4
ATA_DIOR
18 JP8002
ATA_RDY
ATA_CS0
ATA_CS1
4 GNDD
ATA_D10
ATA_D11
ATA_D12
ATA_D13
ATA_D14
ATA_D15
GNDD
ATA_WR
ATA_INT
ATA_D7
ATA_D8
ATA_D6
ATA_D9
ATA_D5
ATA_D4
ATA_D3
ATA_D2
ATA_D1
ATA_D0
(DWX3705)
ATA_A1
ATA_A0
ATA_A2
D20PDY0910E
V+5S_D
ADIN ADIN
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
5 5
standby
*HORIZONTAL
INDB ASSY
V+12S
V+12S
*HORIZONTAL
V+12S
V+12A
V+12E
JUMPER WIRE *HORIZONTAL
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD 17 5 GNDD
V+12
V+12
J
GNDD 16 6 GNDD
OUT3 6
L=100mm 6 OUT3 CN1501 CN1502 CN602
MAT_SEL3 MAT_SEL3 DKN1661-A AKM1292-A VKN1818-A
7 7
36
37
38
39
40
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
10
GNDD 15 7 GNDD
9
1
6
2
(DWX3699)
GNDD 8 8 GNDD
GNDD 14 8 GNDD
3
3
V+5R2 9 9 V+5R2
V+5R2FL 13 9 V+5R2FL DDC1024- PF06PP-S10 DDD1703-
DDD1709-
CRIMP CONNECTOR CRIMP CONNECTOR FFC(SAME FACE)
V+5R2FL 12 FFC 10 V+5R2FL
(REVERSE FACE) L=144mm L=100mm L=90mm
KEY5 11 11 KEY5 AWG #24
L=95mm AWG #22 Pitch=0.5mm
J_SCLK 10 12 J_SCLK
Pitch=1.0mm
KEY0 9 13 KEY0
standby 10
1
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1
2
6
1
JOG_SW 8 14 JOG_SW
CN2 CN7002 CN7005
V+12
V+12
V+12
V+12A
V+12E
GND
GND
GND
GND
ATA_RST
GNDD
ATA_D7
ATA_D8
ATA_D6
ATA_D9
ATA_D5
ATA_D10
ATA_D4
ATA_D11
ATA_D3
ATA_D12
ATA_D2
ATA_D13
ATA_D1
ATA_D14
ATA_D0
ATA_D15
GNDD
GNDD
ATA_DREQ
GNDD
ATA_WR
GNDD
ATA_DIOR
GNDD
ATA_RDY
GNDD
ATA_DACK
GNDD
ATA_INT
GNDD
ATA_A1
GNDD
ATA_A0
ATA_A2
GNDD
ATA_CS0
ATA_CS1
GNDD
V+12S
V+12S
GND
GND
GND
V+5S_D
MAT_SEL1 7 15 MAT_SEL1 B10B-PASK AKM1292-A
*VERTICAL VKN1818-A
*HORIZONTAL
J_DSO 6 16 J_DSO
AC INLET ASSY CN1 *HORIZONTAL
5 B2P3-VH
OUT1 17 OUT1 DKP3975- *VERTICAL
Q
4 18 J_BK_N
J_BK_N
3
L
19 OUT2 LIVE(YELLOW) L=120mm
OUT2 LIVE
2 LIVE LIVE 2 NC
V+5S_D
20 V+3R3
GNDSD
GNDSD
NEUTRAL(WHITE) L=120mm
V+3R3 *HORIZONTAL
EARTH EARTH NEUTRAL *HORIZONTAL
INSW
LPS1
LPS2
HW+
1 NEUTRAL
HU+
HV+
HW-
(DWX3709)
LO+
1
CN7009
HU-
21 J_LAT
HV-
CN7003
LO-
J_LAT NEUTRAL NEUTRAL EARTH(GREEN YELLOW Stripe)
HB
W
U
V
L=63mm
SW POWER
AKM1291-A DKN1313-A
10
11
12
13
1
9
1
5
2
PF05PP-C25 DDD1704-
Use "C13" type AC POWER CORD
CRIMP CONNECTOR FFC(SAME FACE) DKP3769-
SUPPLY
V+3R3
GNDD
JOG2
JOG1
C
/UXJCB DDG1108-
13
12
11
10
1
1
5
2
JP9201
V+5S_D
HU+
HU-
HV+
HV-
HW+
HW-
HB
U
V
W
GNDSD
INSW
LO-
LO+
GNDSD
LPS1
LPS2
D20PYY0405E /SYXJ ADG1244- KM200NA5L DKN1313-A
JUMPER WIRE *HORIZONTAL *HORIZONTAL
D
L=50mm /JXJ DDG1110-
INSW ASSY
/FLXJ ADG1244-
1
JH9201 ADG1239-
JOG2
JOG1
V+3R3
GNDD
B SPCN ASSY
51048-0400
/AXJ DDG1114-
CN9201
K JOG FL (DWX3707)
INSW 1 1 INSW
VKN1425-A VKN1252-A
GNDSD 2 2 GNDSD
JOG1 1 21 JOG1 V9201
CN6001
V+5S_A
GNDSA
VRCOM
V+5S_D
GNDSA
GNDSA
VREF1
A_S1
ST1+
ST2+
VR65
VR78
DEL1074-A
LD78
LD65
ST1-
ST2-
CN6102
A_D
A_C
HW+
7/x6
*HORIZONTAL
CN7001
HU+
CN7004
HV+
HW-
A_B
A_A
HU-
RF
HV-
JFLB ASSY
NC
NC
PD
HB
T+
F+
V+3R3 3 19 V+3R3
F-
VKN1940-A
W
T-
U
V
DKN1445-A DKN1288-A DKN1312-A
V+12LED 4 18
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
V+12LED
10
11
12
1
4
2
9
JOGILM_W 5 17 JOGILM_W
J_DSO 6 16 J_DSO
(DWX3708) DDD1713-
FFC(SAME FACE)
4
4
JOGILM_R
J_BK_N 8 14 J_BK_N
CN9202
JOG_SW
GNDD
*HORIZONTAL ZWNN1007G28-8-07A
J_LAT 10 FFC 12 J_LAT L=70mm GRAY Single Wire
LO+
1
(REVERSE FACE)
3
GNDD 11 11 GNDD
DC MOTOR
10
11
12
A_B 10
A_A 11
VR65 12
VRCOM 13
VR78 14
GNDSA 15
LD78 16
PD 17
LD65 18
GNDSA 19
NC 20
T+ 21
T- 22
F+ 23
F- 24
L=95mm
9
1
2
1
A_S2
VREF1
V+5S_A
A_S1
A_D
A_C
7/x6
RF
NC
W
HB
HW-
HW+
HV-
HV+
HU-
HU+
V+5S_D
GNDD ZWNN1007G28-9-07A
13 9 GNDD
ST1+
ST2+
ST1-
ST2-
GNDD 17 5
V+5R2FL
09SD PICK UP ASSY SPNDIE MOTOR G11
GNDD
V+12FL 18 4 V+12FL
SHEET SW STEPPING
GNDD 19 3 GNDD
GNDD 20 2 GNDD (DSX1078-) MOTOR SK
JOG_SW
GNDD 21 1 GNDD
TM ASSY 09SD-S (DXX2697)
DE007VE0
EARTH LEAD WIRE
L=75mm SLOTIN MECHA ASSY
10.2 SRVB ASSY
E 5/11 CN602
CN7002 CAUTION - FOR CONTINUED PROTECTION AGAINST
A SRVB ASSY
ATA_DREQ
ATA_DACK
RISK OF FIRE, REPLACE WITH SAME TYPE
ATA_DIOR
AKM1292-A
ATA_RDY
E 6/11 CN1502
ATA_RST
ATA_CS0
ATA_CS1
ATA_D10
ATA_D11
ATA_D12
ATA_D13
ATA_D14
ATA_D15
ATA_WR
No.0437002.
ATA_INT
1:7H/
38 ATA_D7
37 ATA_D8
36 ATA_D6
ATA_D9
ATA_D5
ATA_D4
ATA_D3
ATA_D2
ATA_D1
ATA_D0
1:2E,3G,5G/
ATA_A1
ATA_A0
ATA_A2
MFD. BY LITTELFUSE INC.FOR P7001.
(DWX3696)
39 GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
V+12S V+12S1
P7001
DEK1126-A CN7005 VKN1818-A
V+12S 1
1 2
40
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
1
KN7003
Rating:2.000A !
C7373
V+12S 2 CKF1089-A 1
0.1u
GND 3
R7058
GNDSD
CH100p
NM
R7340
R7341
R7342
R7343
R7344
R7345
R7346
R7347
R7348
R7349
R7350
R7351
R7352
R7353
R7354
R7355
GND 4
C7116
C7117
C7118
C7119
C7120
C7122
C7123
C7124
C7125
C7129
C7130
C7131
C7134
C7135
C7136
C7137
CTF1379-A
4 5 6 7 8
8
7
1
2
3
4
GNDSD
L7031
C7374
GND 5 KN7001
R7042
R7043
0.1u
100
100
C7093
C7032 CKF1089-A
R7053
NM
NM
5
100
R7055
V+5S_D 6
5
100
4
1
1:8G 1
8
7
5
C7033
V+5S_D
ATA_DACK
NM
ATA_DREQ
(TS)
(FS)
1:4H
ATA_RDY
ARF_N
ARF_P
ATA_D10
ATA_D11
ATA_D12
ATA_D13
ATA_D14
ATA_D15
ATA_DIOR
ATA_CS0
ATA_CS1
ATA_RESET
R7056
ATA_WR
100
ATA_D7
ATA_D8
ATA_D6
ATA_D9
ATA_D5
ATA_D4
ATA_D3
ATA_D2
ATA_D1
ATA_D0
TE
RFAS
FE
ATA_A1
ATA_A0
ATA_A2
GNDSA V+3S_D
GNDSD 1:5B
C7105 NM
3 4 VREF2
RFDIFO
1:6H 1:4B C7106 NM 1:5B
TEDRV
FEDRV
RFENV
CN7001
DKN1445-A
V+5S_A VREF1
5 9 VHALF
R7028 1M GNDSD
C7114
C7010
0.01u
0.1u
C7083
1200p
V+3S_D 1:4H
1 6
CTF1379-A
CTF1379-A
C7042 0.027u
1000p
1000p
VREF1 10k
PICKUP ASSY OF TM ASSY-S
R7095
L7027
L7028
0.047u
(FS)
(TS)10k
F C7043
4700p
A_S2 2 RFENV 22k C7074
RF R7091
7
6
1M
2.2V BDO 10k
VREF1 3 470p
R7057
R7092
0.1u
0.1u
R7084
10k
C7087
C7088
OFTR
0.1u
10k
1000p
C7079
C7081
R7098
V+5S_A 22k
CTF1379-A
CTF1379-A
CTF1379-A
CTF1379-A
4 TESTSG
1:4H
C7045
L7038
L7037
L7036
L7035
2
3
4
1
E
1800p
2200p
A_S1 1:12E,4E,4F,9B/
0.1u
C7078
35 C7040
5 V+3S_A
C7084
C7086
D 1:4H VHALF
A_D 6 1:6H V+3S_A
1:9A/
36
34
33
32
31
30
29
28
27
26
25
A_C C V+5S_A
CH
VREF2
15k F
C7107
7 ARF_P
0.027u
C7089
1000p
R7104
1800p
C7090
C7091
C7092
C7076
C7077
C7080
C7082
R7099
0.01u
C7071
R7045
0.1u
0.1u
0.1u
47
VIN5
RFINN
RFINP
TESTSG
AGCO
AGCG
PEAK
RFENV
BDO
OFTR
DCRF
RFOUT
0.1u
7/x6
1k
NM
100p
7/x6 8 7H C7027 37 24 R7046 47 ATA_DACK GNDSA
RF 9 1:6H
VAW 38 DFLTOP 23 C7052
ARF_N
B V+5S_A C7020 0.1u VIN6 ATA_RDY
A_B 0.1u
C7098
10 VCC2 DFLTON
C7099
0.1u
CCH1565-A
39 VREF2 22 C7053
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
A 47u/6.3 C7028
99
98
97
96
95
94
93
92
91
90
89
A_A VIN7 1000p
C7031
11 C7021 DCFLT
FEP
100u 16V
0.1u VIN8
0.1u/16 40 21 RFDIFO
VR65 12 VCC3 RFDIFO
NTRYCL/MONI7
NEJECT/MONI6
DASPST/MONI5
MSTPOL/MONI4
MONI3/P12
MONI2/P11
MONI1/P10
MONI0/P9
DTRD
IDGT
VDD3-5
VSS-8
PWM1
PWM0
AVSSA
AD8
AD7
AD6
AD5
AD4
AD3
AD1
AD2
AD0
TECAPA
AVDDA
JITOUT
AVDDB
DSLF1
DSLF2
VREFH
RVI
VHALF
NARF
ARF
AVSSB
PLFLT1
PLFLT2
AVSSC
RFDIF
CSLFLT
WBLIN
AVDDC
TRCRS
ATA_DREQ 133 88
C7018 41 20
VRCOM 13 R7007
1/4W
0.47u/10
C7029 42
VREF1 IC7002 GND1
19
(FS)
FE
ATA_WR 134 87 C7094
R7100
Q7001 0.1u 150p CH LOUT
44 17
3.3k
C7030 VCC1 ASOUT
LD78 16 120 GND3 137 ROUT 84
GNDSA 0.1u VIN3 RFAS ATA_DIOR
45 VIN4 TEOUT 16 AVSSD
PD 17 2SA1036K(PQR) VAW
VIN11 JLINE (TS) ATA_RDY 138 83 OFTR
VFOSHORT
C7022 46 15 IORDY OFTR
TE
LD65 18 ATA_DACK 139 82 BDO
47u/6.3
LPCO1
LPCO2
C7023 47 14 NDMACK BDO
VIN12
DTRD
133 DMARQ
IC7006
LPC1
LPC2
FBAL
0.1u/16
IDGT
STDI
C7142
SEN
SCK
0.1u/16
SODC
GNDSA 19 ATA_INT 140 134 NIOWR 81
48 13 INTRQ JLINE
GNDSA 135 VDD3-6
C7019
(TS)
NC 20
C7001 R7008 XIOCS16 141
136 VSS-9 MN103S71F 80 R7102 C7101 VFOSHORT
2
9
1
10
11
12
4700p 1/4W 137 NIORD 3.3k 0.1u
T+ 21 142 79
6
ATA_A1 TESTSG
6
22 XPDIAG 143 78
1:4G
R7026
C7002
20k
CN7003 AKM1291-A
100p/50 VFOSHORT
ATA_A2 0.1u 147
VDD3-7
MU1(35P) MU2(34P) LOADING SLIDER1 SLIDER2 FOCUS TRACKING SPINDLE /MODE
FG
74
1:8G
DA2 VDD3-4
C7005 (L) 148 73 C7095 VDRAM1R5
LO- 1 ATA_CS0
NM
(L) NCS1FX H H X O O O O O --- short brake DRAMVDD33
LO+ 2 ATA_CS1 149 72 0.1u
GNDSA NCS3FX DRAMVDD15-2
CDJ-2000NXS2
GNDSD
C7011 CH
Q7005 R7066 150
H L X O O O O O --- reversed brake C7100
3 100p/50 1 G1 71
GNDSD D1 5 100 NDASP DRAMVSS-2
R7004 R7076
LPS1 10k 151 L H O X X X X X 70 0.1u FEPEN
4 HDD15 DRV14
0 5 4 C7140
LPS2 2S 152 L L X X X X X X 69 220p/50 FEPDT
5
D
D2 4 3 G2
GNDSD 7 2 154
HDD14 DRV12
68
67
R7010 FEPCLK
7VRSW
12F
12F
ATA_D12 6 3 160
DKN1288-A RS1/10SR***J 61 VHALF
HDD12 NC DRV6
7 2 161 (ST)
C7133
1:8G ATA_D3 60 ST2
0.1u DRIVER IC FLASH ROM IC
HDD3 RS1/10SR****F DRV5
V+5S_D 8 1 162 (ST)
1:8G ATA_D11 F 59 ST1
IC7001 HDD11 DRV4
C7121 V+5S_D 1/4W R7112
100u BD7956FS 1Mb 5 4 163 RS1/4SA***J 58
V+5F ATA_D4 HDD4 DRV3 10K F
1 54 (TS) IC7004
1:8G ATA_D10 6 3 164 R7109 FBAL
CN7009 57
0
CCH1565-A DYWxxxx- /J
R7012
C7110
0.033u
0.047u
0.1u
C7103
C7104
6 49
C7014
C7017
HU- 5 4
1M
1k
0.1u
3 3 30 169
47p
R7003
R7006
R7009
CH
7
CN6101
DSS1157-A
7
X7001
4
BTHC AVM 10k FA13 4 29 FD7 ATA_D8 170 51
R7106
HV- 5 8 47 9 5
A13 DQ7
28 7 2 171
HDD8
174
VDD3-3
C7096 1u
1/4W
1/4W
1/4W
PGND1 LDIN 49
NC1 DQ5 V+3S_D VDDH TXD/EXTRG0/MDATA
HW- 10 45 SPDLFG
7
PGND2 AGND XWE 7 26 FD4 173 SDATA 48
WE# DQ4 NRESET 16.9344MHz
11 44 C7024 C7038 22k SCLOCK
HB 8 C7047 8 25 R7137 174
1000p FD3 47
DRAMVDD15-1
C7003 U SPCNF 0.1u C7060 VSS-4
VDD DQ3 NM
NM (SP) C7109
DRAMVSS-1
U 12 43 0.01u NRST
P6/NSPCCS
NRST
0.68
0.68
0.68
P4/EXCNT0
P5/EXCNT1
P7/FADR17
P8/FADR18
9 175
SPVM1 FG
6 7 8 9
NC2
24 1:8G
0.1u
46
VDD15-1
(SP) VSS
B
FADR11
FADR13
FADR14
FADR16
FADR15
FADR12
FADR10
0.1u V+5S_D
VDD3-1
VDD3-2
V 10 13 42
FADR9
FADR8
FADR7
FADR6
FADR5
FADR4
FADR3
FADR2
FADR1
FADR0
C7097
MMOD
10 23 176
VSS-1
VSS-2
VSS-3
FA16 FD2 45
FDT0
FDT1
FDT2
FDT3
FDT4
FDT5
FDT6
FDT7
V VC
NWE
NOE
NCE
(TS) GNDSD A16 DQ2
DCN1143-A
DCN1143-A
DCN1143-A
14 41
P2
P3
9
5
GNDSD 12 12 21
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
C7009 FA12 FD0 100p/50
41
42
43
44
PGND3 SLO1+
NM 16 ST1- (ST)
R7018 (FS) FEDRV A12 DQ0
39
INSW 13 W SLO1- FA7 13 20 FA0
(ST) 15k F 1:5B A7 A0
C7115 (SP) 17 38 ST2+ C7062
VHALF 14 19 CH
F
FA6 FA1
10k
R7142
R7105
1000p/50 SPVM2 SLO2+
(ST)
100
A6 A1
220p/50
1k
C7085
ST2- C7072
R7078
R7080
R7082
C7069
C7070
C7141
18 37
R7017
C7034
R7021
C7039
0.01u
C7075
0.1u
100p
150p
15 18 100p/50
10k
10k
27k
33k
3 4 9
1u
FA5 FA2
1u
SPRNF SLO2-
1u
R7114 1:1A A5 A2
19 36 C7063
HB SLGND V+12S1 FA4 16 17 FA3 GNDSD
A4 A3
GNDSD 0 20 35 MUTE1 0.1u/16
R7115
HU+
NM
CTL2 1:4G
MUTE2
MUTE1
MUTE2
HU- CTL1
FA17
FA11
FA13
FA14
FA16
FA15
FA12
FA10
XWE
CTF1379-A R7087 1:12D/
XOE
XCE
ST2 7/x6
FD0
FD1
FD2
FD3
FD4
FD5
FD6
FD7
1/4W
FA9
FA8
FA7
FA6
FA5
FA4
FA3
FA2
FA1
FA0
12k F
22 33
12k F
2
R7117
GNDSD
R7118
HV+ SLRNF2
(ST) R7024 1A 100
23 32 1/4W 2 15k F ST1
GNDSD HV- SLRNF1
24 31 R7015 (ST)
HW+ SLVDD
R7025
1800p
1800p
C7036
C7037
25 30 SLIN2
HW- SLIN2 15k F
(SP) C7339 0.01u/50
R7001 26 29 R7330
SPDLEC SPIN SLIN1
4.7k F 27 28 SLIN1 1:12D,6E,7G/
100k Sub Ass'y No:
GNDSD
5V DCDC
0.022u/50
DGND DVCC
8
0.1u/16
V+1R5S
C7340
C7341
C7343
5 7 8 DWX3696- /J
NM
SS
EN
COMP
FB
1:1A ! V+5S_D
BD9328EFJ
IC7305
V+12S1 5V REG IC
FIN
4 9
9
GNDSD GNDM
1:8G
IC7009 1:11B,4B/ D7001 D7002 IC7010 1:1A SRVA DWM2570- /J
R7335
R7336
5.10V
22k
39k
BST
V+12S
VIN
SW
4
GND
2 V+5S_D GNDSD
VIN
V+5S_A
1 5 ! PCB DNP2778-
R7322
VDD
NJM2846DL3-33 ON/OFF
L7303
SERVO BLOCK REFERENCE 7001~7299
22
3 4 VOUT CTH1394-A
R7019
R7027
8
16V
0.1u/16
C7347
8
VSS NC
NM
22k
22k
0 C7342
: RF Signal Route
CCH1565-A
CCH1565-A
3 4
ACG1142-A 10u 16V
10u 16V
R7339
R7040
CH
1 C7338
NM
16V
10u
CONT NC VIN
C7126
C7127
C7128
C7138
C7132
LTC014YEB
0.1u
0.1u
2 0 0.01u/50
R7334 R7333 R7332
S-1155B15-U5
C7334
100u
CCH1565-A
3
C7344
16V
0
0.018u
47u/16
C7143
C7049
C7044
C7046
NM
GND
ACG1142-A
C7345
0.1u
0.1u
(TS)
16V
CCH1565-A
CKF1089-A
10k F 47k F
Q7003 4
: Tracking Servo Signal Route
KN7002
47u/6.3
47u/16
C7048
C7050
C7051
C7057
C7055
C7059
C7058
VOUT
0.1u
0.1u
0.1u
0.1u
LTC014YEB GNDSA
100u
5 (SP)
C7346
100u
NC 1
C7336
GNDSD
(ST)
3.3V REG IC
GNDSA GNDSD GNDSD
(L)
: Stepping Motor Signal Route
: Loading Motor Signal Route
5
A A
F
A
1 2 3 4
HV- 9 8 HV-
Sub Ass'y No:
HW+ 8 7 HW+
B HW- 7 6 HW- DWX3697- /J
HB 6 5 HB
(SP)
A
U 5
(SP) 4 U SRVA DWM2570- /J
V 4 3 V
(SP)
3
INSW DWX3697- /J
W 2 W
GNDSD 2 1 NC INSW UNIT PCB DNP2778-
INSW 1
CN6103
VKN1940-A
2 GNDSD
1 INSW
GNDSD
C
Sub Ass'y No:
DWX3698- /J
SRVA DWM2570- /J
D D SLMB ASSY
(DWX3707)
Slot in
Mecha SW
CN9001 S9001
KM200NA5L
DSG1017-A
LPS2 1 2
CN7003
LPS2 5
LPS1 1 2
LPS1 4
S9002
3 DSG1017-A
GNDSD
LO+ 2
A
LO- 1
ZWNN1007G28-9-07A
L=70mm WHITE Single Wire
(L)
LO+
LO+
GNDSD LOADING MOTOR
(L)
LO-
LO- DXM1230-
E
ZWNN1007G28-8-07A
L=70mm GRAY Single Wire
DWX3707- /J
Reference 9001-9100
PNLA DWM2571- /J
SLMB DWX3707- /J
PCB DNP2779-
B C D B C D
6 CDJ-2000NXS2
1 2 3 4
10.4 MAIN ASSY (1/11)
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
V+1R8_CPU V+3R3_CPU V+3R3_CPU
E 7/11
V+1R2_CPU
1:15E 1:15B
1:16D 1:15B
R182
R164
R150
R110
R144
R149
R151
4.7k
4.7k
4.7k
4.7k
4.7k
4.7k
4.7k
CPU_WAIT
1000p/50
1000p/50
1000p/50
1000p/50
1000p/50
1000p/50
1000p/50
1000p/50
1000p/50
1000p/50
0.01u/16
0.01u/16
0.01u/16
0.01u/16
0.01u/16
0.01u/16
0.01u/16
0.01u/16
0.01u/16
0.01u/16
1000p/50
1000p/50
1000p/50
1000p/50
1000p/50
1000p/50
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.01u/16
0.01u/16
0.01u/16
0.01u/16
0.01u/16
0.01u/16
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
0.1u/10
1B;7:10D
CPU_CS6A
2:13J
to DSP
E 7/11
C141
C142
C145
C148
C149
C150
C143
C147
C144
C146
CPU_CS0 to FLASH
C10
C25
C26
C27
C28
C29
C32
C33
C35
C38
C40
C41
C42
C11
C12
C13
C30
C36
C24
C31
C34
C37
C39
C1
C2
C5
C4
C8
C9
C3
C6
C7
C44
C47
C53
C60
C64
C67
C43
C45
C48
C50
C56
C57
C58
C59
C61
C62
C65
C66
C68
C69
C74
C75
C77
C49
C52
C54
C70
C73
C46
C51
C55
C63
C71
C72
UPP_CH0_WAIT
E 1/11 MAIN ASSY (DWX3672)
UPP_CH0_WE#
CPU_UPP_START R4 100
2:13J
CPU_RD
E 2/11 R11
E 5/11
GNDD GNDD FLASH_RDY GNDD
CPU_USB CPU_WE0 5.6k
5:10D 2:9K
CPU_DSP_BOOTTXD
7:10H
ALARM
CPU_PANEL CPU_ADRS_BUS
C76 11:2D 2:8J
CPU_IDE_ADRS1
CPU_ETH CPU_DATA_BUS
CPU_ADRS20
CPU_ADRS13
0.1u/10 5:10K
E 2/11
V+3R3_CPU 2:2J
IC6 1:15B
CPU_DSP_BOOTTXD
CPU_SCIF2_RXD
CPU_RMII_REF_CLK
CPU_ADRS24
SH2_SH4_BUS
5
CPU_RMII_CRS_DV
CPU_PTM3
5
CPU_DDR2_DATA
4.7k
CPU_WAIT_EN
CPU_RDWR
CPU_RMII_TX_EN
IC15
CPU_RMII_RX_ER
1 8
CPU_UPP_MASK
CPU_CS6A
CPU_ADRS0
1A 7:10J;11:2B
CPU_DSP_ENABLE
CPU_RMII_RXD1
CPU_SCIF2_SCK
CPU_SCIF2_TXD
CPU_RMII_RXD0
CPU_RMII_TXD0
CPU_RMII_TXD1
UPP_CH0_WAIT
VCC 2:2F
CPU_DSP_RXD
9A;7:10D
CPU_DSP_CLK
22
CPU_IDE_DATA13
CPU_IDE_DATA15
CPU_IDE_DATA12
CPU_IDE_DATA11
CPU_IDE_DATA14
CPU_IDE_DATA10
1B
CPU_DSP_CS
2 7 CPU_CLKGEN 1 5
CPU_IDE_ADRS2
CPU_IDE_ADRS0
CPU_DDR2_CONT
CPU_IDE_DATA8
CPU_IDE_DATA9
R142
CPU_UPP_START
22
1Y 7:10K INB VCC
22
22
CPU_DATA15S
CPU_DATA11S
CPU_DATA12S
CPU_DATA10S
CPU_DATA13S
CPU_DATA14S
CPU_IDEIOWR
2:2F
CPU_CKO
CPU_MDC
CPU_IDEIORD
6A;7:10E
CPU_IODREQ
CPU_DATA7S
CPU_DATA8S
CPU_DATA5S
CPU_DATA6S
CPU_DATA9S
CPU_DATA2S
CPU_DATA4S
CPU_ADRS22
R180
CPU_ADRS21
CPU_ADRS17
CPU_ADRS16
CPU_ADRS19
CPU_ADRS15
CPU_ADRS11
CPU_ADRS18
CPU_ADRS10
CPU_ADRS14
CPU_ADRS12
3 6 2
CPU_ADRS23
2Y
CPU_IDECS1
CPU_IDECS0
CPU_ADRS3
CPU_ADRS5
CPU_ADRS9
CPU_ADRS4
CPU_ADRS7
CPU_ADRS8
CPU_ADRS2
CPU_ADRS6
CPU_ADRS1
CPU_IDEINT
2B INA
V+3R3_CPU
7:10G
4 GND 5 3 4
R135
CPU_CS5A
2A GND OUTY
R143
1:14G,15H,16J,2J,2G,2C,2D,2B,2H,3J,3F,4B,4A,7A,9K/2:11H/5:7I/
4.7k
CPU_CS4
R134
R139
UPP_CH0_START
NM GNDD V+3R3_CUSB
TC7SH08FUS1
UPP_CH0_ENABLE 1:3I/
C166 ZZ4
4.7k
GNDD V+3R3 3.3V FILTER
22
22
0.1u/10
22
22
GNDD F4
6:7D NM
R52
R5
E 11/11 E 7/11
47k
10k
R13
R19
R23
R24
F3
4.7k
4.7k
0
R141
22
1 3
R179
R181
R140
R137
1 2
R67
E 5/11
3
2
CCG1352-A
DCH1201-A
DCH1201-A
DCH1201-A
10u/10
E 7/11, 11/11
C110
10u/10
10u/10
C111
C112
A25 B25 C25 D25 E25 F25 G25 H25 J25 K25 L25 M25 N25 P25 R25 T25 U25 V25 W25 Y25 AA25 AB25 AC25 AD25 AE25
R53
NM
VSS2 PTN0 PTL3 PTL0 PTM4 PTZ0 CKO IOIS16 CS5A WE1 A24 A20 A15 A13 A12 A8 A6 A1 A0 D29 D25 D22 D18 D14 VSS57
RMII_CRS_DV RMII_TXD0 MSIOF0_TSYNC IODREQ IDEIOWR# IDED14 IDED10
LCDLCLK ZZ5 V+3R3_CUSBA
IC14 F1
V+3R3_CPU NM 1:3I/
H337S3959
1:15B GNDD 1 3
CPU_PTN5 A24 B24 C24 D24 E24 P24
1 8 APL_RST F24 G24 H24 J24 K24 L24 M24 N24 R24 T24 U24 V24 W24 Y24 AA24 AB24 AC24 AD24 AE24
GND VCC
DCH1201-A
DCH1201-A
GND VCC CPU_PTX6 PTN5 PTL7 PTL5 PTM5 PTZ1 PTU6 CS6A CS4 RD A25 A23 A19 A14 A9 A7 A2 D30 D28 D26 D19 D17 D13 D9 D4
E 6/11
10u/10
10u/10
PTM7
C113
C114
2 7 CPU1R2_CNT
SDA 9 RST RMII_RXD0 RMII_REF_CLK MSIOF0_TXD IDEA0 IDECS0# IDEIORD# IDED11 IDED9 2
SDA RST CPU_PTX7 6:6C
3 6 MSIOF0_TSCK
NC SCL
0.1u/10
DA2J101
NC1 PAD SCL
C133
4.7k
R17
4 5
4.7k
R10
D1
NC NC
NC2 NC3 A23 B23 C23 D23 E23 F23 G23 H23 J23 K23 L23 M23 N23 P23 R23 T23 U23 V23 W23 Y23 AA23 AB23 AC23 AD23 AE23
PTX2 PTL2 PTM6 PTU7 WAIT CS6B CS0 WE0 A21 A16 A10 A5 A4 WE2 D27 D24 D20 D16 D12 D10 D6 D2
2200p/50
0.1u/10
C134
C153
4.7k
4.7k
R16
R66
SCIF2_RXD RMII_RX_ER RMII_TXD1 MSIOF0_RXD MSIOF0_RSCK IDEA2 IDECS1# IDEINT IDED12 IDED8
CPU_MDQ21
A22 B22 C22 D22 E22 F22 G22 H22 J22 K22 L22 M22 N22 P22 R22 T22 U22 V22 W22 Y22 AA22 AB22 AC22 AD22 AE22 GNDD V+1R8 V+1R8_CPU
Authentication PTX6 PTX5 PTX3 PTN2 PTL1 PTN4 PTL6 PTL4 PTM2 CS5B RDWR A22 A17 A18 A3 D31 D21 D15 D23 D7 D11 D8 D5 MDQ21 VCCQ_DDR10 CPU_DATA3S 6:7C 1.8V FILTER
GNDD 10 1:13J,3A/2:7A/
Coprocessor CPU_SCL0 R15 LNKSTA MDC SCIF2_TXD SCIF2_SCK RMII_RXD1 RMII_TX_EN MSIOF0_RSYNC IDEA1 IDED13 IDED15
CPU_DATA1S
CPU_SDA0 F6
CPU_MDQ26 1 2
R14 10
V+3R3_CPU TPUTO3 CPU_MDQ29
1:15B CPU_ETHER_INT CCG1352-A 3
DCH1201-A
R163 A21 B21 C21 D21 E21 F21 G21 H21 J21 K21 L21 M21 N21 P21 R21 T21 U21 V21 W21 Y21 AA21 AB21 AC21 AD21 AE21
10u/10
C139
C140
NM
PTZ5 PTX7 SDA0 SCL0 VCCQ_SR3 VSS6 VSS7 VCCQ1_1 VCCQ1_2 VCCQ1_3 VSS19 VCCQ1_4 VCCQ1_5 A11 WE3 VSS44 VCCQ1_6 VCCQ1_7 VCCQ1_8 VSS46 VSS53 D3 D1 MDQ26 MDQ29 CPU_DATA0S
4.7k
CPU_MDIO
CPU_MDQ18
CPU_MDQ24
R158 CPU_DSP_RDREQ CPU_DSP_RDREQ
CPU_MDQ31
4.7k A20 B20 C20 D20 E20 AA20 AB20 AC20 AD20 AE20 3.3V
PTU0 PTZ7 PTZ3 PTX4 VCCQ_SR2 VSS52 D0 MDQ18 MDQ24 MDQ31 CPU_MDQ16 GNDD
MDIO
CPU_MDQ23
E 8/11
R157 4.7k DSP_BOOT_DONE DSP_BOOT_DONE
CPU_MDQS3P
R156 4.7k UPP_BOOT_REQ UPP_BOOT_REQ
CPU_MDQS3N
R44 4.7k BOOT_COMPLETE BOOT_COMPLETE A19 B19 C19 D19 E19 AA19 AB19 AC19 AD19 AE19
CPU_FPGA_INIT_B PTU4 PTU3 PTZ6 PTZ4 VCCQ_SR1 VCCQ_DDR8 MDQ16 MDQ23 MDQS3 MDQS3
V+1R2
CPU_MDQS2N
E 5/11 GNDD
R46 4.7k UPP_BOOT_ACK CPU_MUTE
CPU_FPGA_PROG_B
MAIN CPU
CPU_MDQS2P
6:10C
1.2V FILTER V+1R2_CPU
6
Q1
6
CPU_MDQ25
V+1R2_CPLL CPU_DSP_BOOT1 1:1A,3J/7:12D/
1:16E CPU_MDQM3 1 D1 6
UPP_BOOT_ACK V+1R2_CPLL
A18 B18 C18 D18 E18 IC10 AA18 AB18 AC18 AD18 AE18 D4
E 7/11
C151
0.1u/10 2 D2 5 1:2E/
CPU_FPGA_DONE PTV1 PTE7 PTU2 PTU5 PTU1 VCCQ_DDR7 MDQS2 MDQS2 MDQ25 MDQM3 L1
C106
10u/10 SH2_MISO1
R8A77240D500BG2 CPU_MDQ22
3 G
D3
4 1
F2
2 CTF1394-A
CPU_MDQM2 S
DCH1201-A-T SH2_SSL10 R47 22 V+1R2_CFLL
CPU_MDQ27 CCG1352-A 3
V+1R2_CFLL SH4_MSIOF1_TSCK R27 L2 1:2F/
E 5/11
100u/6.3
CPU_MDQ30 RTQ045N03 CTF1394-A
C108
1:16E SH4_MSIOF1_RXD 22
C100 GNDD A17 B17 C17 D17 E17 AA17 AB17 AC17 AD17 AE17
0.1u/10 ZZ1
SH2_STARTUP PTV5 PTV3 PTV4 PTV2 PTE6 MVREF1 MDQ22 MDQM2 MDQ27 MDQ30 V+1R2_CPUUV
C23 CPU_MDQ17 1.2V SWITCH
10u/10 SH4_MSIOF1_RSCK R22 MSIOF1_RXD MSIOF1_TSCK MSIOF1_TSYNC L3 1:3H/
CPU_MDQ20 NM
DCH1201-A-T R48 22 MSIOF1_TXD GNDD
USBHUB_RST SH2_SSL10 CPU_MDQ19
5:8C R7 22
22 ZZ2
FPGA_RST V+3R3_CPU CPU_MDQ28 V+1R2_CUSB
7:10K R153 22 A16 B16 C16 D16 E16 K16 L16 M16 N16 P16 R16 T16 AA16 AB16 AC16 AD16 AE16 L4 1:3H/
1:15B NM
R80
VDD_PLL VSS_PLL PTV7 PTV6 PTV0 VDD4 VDD6 VDD8 VDD10 VDD12 VDD14 VDD18 VSS51 MDQ17 MDQ20 MDQ19 MDQ28
CDJ-2000NXS2
CPU_MCLKP
ETHER_RST 10k CPU_USB_HSTPWREN MSIOF1_RSYNC MSIOF1_RSCK ZZ3
5:10I R128 22 CPU_MCLKN V+1R2_CUSBA
R79 CPU_USB_HSTPWRFL L5
CPU_MA6 1:3I/
DSP_RST NM
8:7F R126 22 10k CPU_MA11
A15 B15 C15 D15 E15 K15 L15 M15 N15 P15 R15 T15 AA15 AB15 AC15 AD15 AE15
PNL_RST
11:5D R132 22 H:RESET R45
VDD_FLL VSS_FLL PTH1 PTN6 PTN7 VDD3 VSS18 VSS24 VSS29 VSS34 VSS39 VDD17 VCCQ_DDR6 MCLK MCLK MA6 MA11 CPU_MA8
E 11/11 SH2_RESET
11:5D R112 22 H:RESET
10k CPU_USB_HSTSTOP
CPU_PNL_CNVss
CPU_ETHER_RST
CPU_MA12
CPU_MCS
CPU_MA2
V+3R3_CPU CPU_DSP_RST A14 B14 C14 D14 E14 N14 P14 R14 AA14 V+3R3_CPU
IC8 K14 L14 M14 T14 AB14 AC14 AD14 AE14
1:15B CPU_PNL_BUSY PTH0 PTH3 PTH6 PTH4 PTH2 VSS12 VSS17 VSS23 VSS28 VSS33 VSS38 VSS43 VCCQ_DDR5 MA8 MA12 MCS MA2 1:15B
CPU_MCAS V+1R8DSP
4.7k
4.7k
NM R58
1 5
R8
CPU_RST
INB VCC CPU_IDE_DATA0 CPU_MA0 10:9D
14I;3K;2:9K;5:6K;6:5D;10:12E
R57
2
R122
CPU_MRAS
2.2k
2.2k
R90
R96
4.7k
INA
3 4 CPU_PNL_RST
CPU_MODT
R106
R108
CPU_SCL1
NM
NM
GND OUTY
E 2/11, 5/11,
CPU_FPGA_RST A13 B13 C13 D13 N13 P13 R13 T13 AA13 AB13
E13 K13 L13 M13 AC13 AD13 AE13 3H;5:8D;11:5B
D3
0.1u/10
R155
PTH5 PTH7 PTK1 PTK2 PTK0 VSS11 VSS16 VSS22 VSS27 VSS32 VSS37 VSS42 VSS50 MCAS MA0 MRAS MODT
4.7k
4.7k
C95
R43
TC7SH00FUS1 CPU_MA4
CPU_IDE_DATA4 IDED0 DA2J101
CPU_MA5 CPU_SDA1 CPU_DSP_SCL1
CPU_IDE_DATA3
E 3/11
3G;5:8D;11:5B Q3 3:14E
6/11, 10/11
CPU_MBA1 S1 1 6 D1
CPU_IDE_DATA2
CPU_SH2_RST CPU_MWE
CPU_IDE_DATA1
E 5/11, 11/11
A12 B12 C12 D12 E12 K12 L12 M12 N12 P12 R12 T12 AA12 AB12 AC12 AD12 AE12 CPU_DSP_SDA1
CPU_SDA1 G1 2 5 G2 3:14E
GNDD PTK3 PTK4 PTK5 PTK6 VCCQ_VIO2 VSS10 VSS15 VSS21 VSS26 VSS31 VSS36 VSS41 VCCQ_DDR4 MA4 MA5 MBA1 MWE CPU_MCKE
14G;5:8D;11:5B CPU_IDE_DATA7 IDED1 IDED2 IDED3 IDED4
CPU_MA1
CPU_SCL1 D2 3 4 S2
CPU_MBA2
14G;5:8D;11:5B
E 5/11,11/11
CPU_IDE_DATA6
CPU_MBA0 EM6K7
CPU_IDE_DATA5
R160
R161
A11 B11 C11 D11 E11 K11 L11 M11 N11 P11 R11 T11 AA11 AB11 AC11 AD11 AE11
0
D2
PTK7 PTS0 PTS6 PTS1 VCCQ_VIO1 VDD2 VSS14 VSS20 VSS25 VSS30 VSS35 VDD16 VCCQ_DDR3 MCKE MA1 MBA2 MBA0 CPU_MA9
R40 IDED5 IDED6 IDED7
CPU_MA7 DA2J101
22 CPU_MA3
CPU_MA10
V+3R3_CPU A10 B10 C10 D10 E10 K10 L10 M10 N10 P10 R10 T10 AA10 AB10 AC10 AD10 AE10
IC7
1:15B V+1R2_CUSB PTS2 PTS4 SDA1 PTS3 VSS4 VDD1 VDD5 VDD7 VDD9 VDD11 VDD13 VDD15 VSS49 MA9 MA7 MA3 MA10 CPU_MDQ2 V+3R3_CPU
TC7WHU04FK 1:16F CPU_MDQ0 CPU RESET 1:15B
CPU_USB_VBUS0
CPU_MDQ5
1 8 CPU_IDEIORDY
1A VCC
C22 CPU_MA13 50ms IC11
0.1u/10
R113
PST8430N
3.3k
2 7 A9 B9 C9 D9 E9 AA9 AB9 AC9 AD9 AE9
3Y 1Y C21
1000p/50
MDQ2
7
3 6 SCL1 PTS5 VBUS0 DG12_0 DV12_0 VCCQ_DDR2 MDQ0 MDQ5 MA13 CPU_MDQS0P 5 1
7
2A 3A IDEIORDY CD OUT
4 5
V+1R2_CPUUV CPU_MDQS0N 2
GND 2Y 1:16F CPU_MDQ13 VDD
4 3
C20 CPU_MDQ7 NC GND
0.1u/10
C168 0.1u/10 CPU_USB_DM0
C115
C116
NM
C19 A8 B8 C8 D8 E8 AA8 AB8 AC8 AD8 AE8
6800p/25
0.1u 1000p/50 DM0 DG33_0 AV12_0 UG12_0 UV12_0
C117
VCCQ_DDR1 MDQS0 MDQS0 MDQ13 MDQ7 CPU_MDQM0
GNDD R145
V+1R2_CUSBA CPU_MDQ6
1M 1:16F
R159
470
CSS1760-A CPU_MDQ15
3 X2 4 C18 CPU_MDQ10
GND2 0.1u/10 CPU_USB_DP0
C17 A7 B7 C7 D7 E7 AA7 AB7 AC7 AD7 AE7 GNDD
1000p/50
R38 DP0 DV33_0 AG12_0 DG12_1 DV12_1 MVREF0 MDQM0 MDQ6 MDQ15 MDQ10 CPU_MDQ1 CPU_RST
2 1
GND1
V+3R3_CUSB 1G;3K;2:9K;5:6K;6:5D;10:12E
X1 1:16B CPU_MDQ3
5p CH
C99
100
CH
6p
X1
C169
C15 CPU_MDQS1N
0.1u/10 R18
C14
CPU_MDQ8
GNDD NM
E 5/11 C16
CPU_MDQM1
CPU_CONF 1:15B
1000p/50 R116 CPU_MDQS1P 8L R6
A5 B5 C5 P5 R5 Y5 AA5 AB5 CPU_CONF_MD0
D5 E5 F5 G5 H5 J5 K5 L5 M5 N5 T5 U5 V5 W5 AC5 AD5 AE5
OSC_INV
R2
0
V+3R3_CPU V+1R2_CPU 5.6k F REFRIN0 DG33_1 DV33_1 AG12_1 VSS3 VSS5 VCCQ1 VCCQ2 VSS8 VSS9 VSS13 VCCQ_MMC1 VCCQ_MMC2 VCCQ_SDC1 VCCQ_SDC2 VSS40 VCCQ_LCD1 VCCQ_LCD2 VCCQ_LCD3 VSS45 VSS47 MSLD MDQ4 MDQM1 MDQS1 0
V+3R3_CPU MD[2:0] CLOCK MODE
IC9 1:15B 1:15E R26
001(1h):X30 CPU_CONF_MD1
TC7WHU04FK 1:15B
CPU_MDQ14 MD3 BUS WIDTH
0:16bit 0
CPU_MDQ11 R28
1 8 MD5 ENDIAN CPU_CONF_MD2
1A VCC A4 B4 C4 D4 E4 F4 G4 H4 J4 K4 L4 M4 N4 P4 R4 T4 U4 V4 W4 Y4 AA4 AB4 AC4 AD4 AE4
V+5S_D GNDD 1:LITTLE
2 7 CPU_USB_DM1 0
3Y DM1 AV33_1 AV12_1 MD5 MD8 MD0 RESETP STATUS0 TRST PTG5 NMI PTW3 PTX1 PTY6 PTY3 PTC6 PTD4 PTE0 PTE4 PTF7 PTF3 PTM0 VSS54 MDQ14 MDQ11
1Y 6:2E Q5 5:5B MD8,TST FOR VENDOR TEST
AUDCK SDHI0WP SDHI0D1 LCDD6 LCDD12 LCDD16 LCDD20 LCDVSYN LCDDCK R29
3 6 LTA024EEB ,TSTMD CPU_CONF_MD3
2A 3A
R61 CPU_MDQ12 BOOT BOOT MODE
4 5 0
GND 2Y 0:NORMAL
CPU_MDQ9
R1
100
R30
0 CPU_CONF_MD5
A3 B3 C3 D3 E3 F3 G3 H3 J3 K3 L3 M3 N3 P3 R3 T3 U3 V3 W3 Y3 AA3 AB3 AC3 AD3 AE3
CPU_USB_DP1 R37 DP1 AG33_1 MD2 TSTMD STATUS2 BOOT TMS PTG0 PTG3 MPMD PTW0 PTW4 PTX0 PTY4 PTZ2 PTC3 PTD0 PTD3 PTD6 PTE1 PTF0 PTF4 PTM1 MDQ12 MDQ9 0
4.7k
R42
C103 0.1u/10 5:5B AUDATA0 AUDATA3 DIRECTION SDHI0D2 SCIF0_RXD V+1R8_CPU R31
LCDD3 LCDD8 LCDD11 LCDD14 LCDD17 LCDD22
1u/10
C107