Multi Player: This Manual Is Applicable To The Following Model (S) and Type (S)

ORDER NO.
RRV4128
CDJ-850
MULTI PLAYER
CDJ-850
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Remarks
CDJ-850 SYXJ8 AC 220 V to 240 V
CDJ-850 CUXJ AC 120 V
CDJ-850 FLXJ AC 110 V to 240 V

CDJ-850 KXJ5 AC 220 V
CDJ-850 AXJ5 AC 220 V to 240 V
For details, refer to "Important Check Points for good servicing".
PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2010
K-IZV JULY 2010 Printed in Japan
1 2 3 4
SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
B This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive
harm.
Health & Safety Code Section 25249.6 - Proposition 65
CAUTION
This product is a class 1 laser product classified
C
under the Safety of laser products, IEC 60825-1:2007.
CLASS 1 LASER PRODUCT

D58-5-2-2a_A1_En
D
IMPORTANT
Laser Pickup specifications and Laser characteristics
THIS PIONEER APPARATUS CONTAINS
LASER OF CLASS 1. For CD Wave length (typ) : 790 nm
SERVICING OPERATION OF THE APPARATUS Operation output : 4 mW CW, Class 1
S H O U L D B E D O N E B Y A S P E C I A L LY Maximum output : Class 1 (Under fault condition)
INSTRUCTED PERSON.
Additional Laser Caution

E
1. Laser Interlock Mechanism
The position of the switch (S1702) for detecting loading
completion is detected by the system microprocessor, and the
design prevents laser diode oscillation when the switch is not in
LPS1 terminal side (when the mechanism is not clamped and
LPS1 signal is high level.)
Thus, the interlock will no longer function if the switch is
deliberately set to LPS1 terminal side.
( if LPS1 signal is low level ).
In the Service mode the interlock mechanism will not function.
Laser diode oscillation will continue, if pin 41 of TC94A15FG
(IC201) on the MAIN Assy is connected to GND, or else the
terminals of Q201 are shorted to each other (fault condition).
F
2. When the cover is opened, close viewing of the objective lens
with the naked eye will cause exposure to a Class 1 laser beam.
2 CDJ-850
1 2 3 4
5 6 7 8
LABEL CHECK A
(Printed on the chassis) (Printed on the chassis) (Printed on the chassis)
SYXJ8 CUXJ FLXJ
(Printed on the chassis) (Printed on the chassis)
KXJ5 AXJ5
CDJ-850 3
5 6 7 8
1 2 3 4
A
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.

B
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
C
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.

D
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
a Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
E 3. Lubricants, Glues, and Replacement parts

Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
5. Shipping mode and Shipping screws
F To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
4 CDJ-850
1 2 3 4
5 6 7 8
CONTENTS
SAFETY INFORMATION.......................................................................................................................................................... 2
1. SERVICE PRECAUTIONS .................................................................................................................................................... 6
1.1 NOTES ON SOLDERING ............................................................................................................................................... 6 A
1.2 ABOUT POWER SUPPLY MONITORING ...................................................................................................................... 6
2. SPECIFICATIONS................................................................................................................................................................. 7
2.1 SPECIFICATIONS .......................................................................................................................................................... 7
2.2 USABLE DISCS AND USB DEVICES............................................................................................................................ 8
2.3 PANEL FACILITIES....................................................................................................................................................... 10
3. BASIC ITEMS FOR SERVICE ............................................................................................................................................ 13
3.1 CHECK POINTS AFTER SERVICING ......................................................................................................................... 13
3.2 JIGS LIST ..................................................................................................................................................................... 13
3.3 PCB LOCATIONS ......................................................................................................................................................... 14
4. BLOCK DIAGRAM .............................................................................................................................................................. 16
4.1 OVERALL WIRING DIAGRAM ..................................................................................................................................... 16
4.2 SIGNAL BLOCK DIAGRAM.......................................................................................................................................... 18
B
4.3 POWER SUPPLY BLOCK DIAGRAM........................................................................................................................... 20
5. DIAGNOSIS ........................................................................................................................................................................ 22
5.1 POWER ON SEQUENCE............................................................................................................................................. 22
5.2 TROUBLESHOOTING.................................................................................................................................................. 23
5.3 DIAGNOSIS OF THE PICKUP ASSY........................................................................................................................... 32
5.4 CONNECTION CHECK WITH THE PC........................................................................................................................ 33
5.5 ABOUT POWER SUPPLY MONITORING .................................................................................................................... 34
5.6 ABOUT THE PROTECTORS........................................................................................................................................ 34
6. SERVICE MODE ................................................................................................................................................................. 35
6.1 SERVICE MODE .......................................................................................................................................................... 35
6.2 ABOUT THE DEVICE OF CDJ-850.............................................................................................................................. 35
6.3 DETAILS ON SERVICE MODE .................................................................................................................................... 36
7. DISASSEMBLY ................................................................................................................................................................... 42 C
8. EACH SETTING AND ADJUSTMENT ................................................................................................................................ 52
8.1 NECESSARY ITEMS TO BE NOTED........................................................................................................................... 52
8.2 USER SETABLE ITEMS ............................................................................................................................................... 52
8.3 UPDATING OF THE FIRMWARE ................................................................................................................................. 53
8.4 JOG DIAL ROTATION LOAD ADJUSTMENT ............................................................................................................... 55
9. EXPLODED VIEWS AND PARTS LIST............................................................................................................................... 56
9.1 PACKING SECTION ..................................................................................................................................................... 56
9.2 EXTERIOR SECION..................................................................................................................................................... 58
9.3 CONTROL PANEL SECTION ....................................................................................................................................... 60
9.4 JOG DIAL SECTION .................................................................................................................................................... 62
9.5 SLOTIN MECHA SECTION .......................................................................................................................................... 64
10. SCHEMATIC DIAGRAM .................................................................................................................................................... 66 D
10.1 CNCT, SLMB and JINT ASSYS.................................................................................................................................. 66
10.2 MAIN ASSY (1/4)........................................................................................................................................................ 68
10.3 MAIN ASSY (2/4)........................................................................................................................................................ 70
10.4 MAIN ASSY (3/4)........................................................................................................................................................ 72
10.5 MAIN ASSY (4/4)........................................................................................................................................................ 74
10.6 CMPX (1/2) and USBA ASSYS .................................................................................................................................. 76
10.7 CMPX ASSY (2/2) ...................................................................................................................................................... 78
10.8 DFLB ASSY ................................................................................................................................................................ 80
10.9 KSW1 and KSW2 ASSYS .......................................................................................................................................... 82
10.10 JFLB and JOGB ASSYS........................................................................................................................................... 84
10.11 SLD1, PSWB and SLD2 ASSYS .............................................................................................................................. 86
10.12 POWER SUPPLY and ACIN ASSYS ........................................................................................................................ 88 E
10.13 VOLTAGES ............................................................................................................................................................... 90
10.14 WAVEFORMS........................................................................................................................................................... 91
10.15 EACH SIGNAL LEVEL.............................................................................................................................................. 93
11. PCB CONNECTION DIAGRAM ........................................................................................................................................ 94
11.1 CNCT, SLMB and JINT ASSYS.................................................................................................................................. 94
11.2 MAIN ASSY ................................................................................................................................................................ 98
11.3 CMPX and USBA ASSYS......................................................................................................................................... 102
11.4 DFLB ASSY .............................................................................................................................................................. 106
11.5 KSW1 and KSW2 ASSYS ........................................................................................................................................ 110
11.6 JFLB and JOGB ASSYS........................................................................................................................................... 112
11.7 SLD1, PSWB and SLD2 ASSYS .............................................................................................................................. 114
11.8 POWER SUPPLY and ACIN ASSYS ........................................................................................................................ 116
F
12. PCB PARTS LIST ............................................................................................................................................................ 118
CDJ-850 5
5 6 7 8
1 2 3 4
1. SERVICE PRECAUTIONS
1.1 NOTES ON SOLDERING
A • For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
• Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 ºC.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 ºC in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
Do NOT use a soldering iron whose tip temperature cannot be controlled.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
B
temperatures (hard to melt/easy to harden).
The following lead-free solders are available as service parts:

• Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.
1.2 ABOUT POWER SUPPLY MONITORING

This unit always monitors for power failure and will shut itself off immediately after an error is detected. If an error is generated,
the STANDBY LED will flash after the unit shuts itself off. After the unit shuts itself off because of an error, unplug the AC power
D
cord and wait 1 minute before turning the unit ON by pressing the STANDBY/ON key.
Repair the unit, according to “5.5 ABOUT POWER SUPPLY MONITORING.”
6 CDJ-850
1 2 3 4
5 6 7 8
2. SPECIFICATIONS
2.1 SPECIFICATIONS
Power requirements........ AC 220 V to 240 V, 50 Hz/ 60 Hz (SYXJ8) A
AC 120 V, 60 Hz (CUXJ)
AC 110 V to 240 V, 50 Hz/ 60 Hz (FLXJ)
AC 220 V, 60 Hz (KXJ5)
AC 220 V to 240 V, 50 Hz/ 60 Hz (AXJ5)
Power consumption................................................................... 21 W
Power consumption (standby).................................................. 0.4 W
Main unit weight....................................................................... 2.3 kg
Max. dimensions........ 305 mm (W) × 105.5 mm (H) × 364.4 mm (D)
(12 in. (W) × 4.2 in. (H) × 14.3 in. (D))
Tolerable operating temperature.............................. +5 °C to +35 °C
(+41 °F to +95 °F)
Tolerable operating humidity.............5 % to 85 % (no condensation)
B
Analog audio output (AUDIO OUT L/ R)
Output terminal.............................................................RCA terminal
Output Level........................................................... 2.0 Vrms (1 kHz)
Frequency response.................................................. 4 Hz to 20 kHz
S/ N ratio.................................................................................115 dB
Total harmonic distortion.......................................................0.003 %
USB downstream section (USB)

Port..........................................................................................Type A
Power supply.......................................................5 V/ 500 mA or less
USB upstream section (USB)

Port..........................................................................................Type B
C
Control output (CONTROL)
Port...................................................................................... Mini-jack
• The specifications and design of this product are subject to

change without notice.
CDJ-850 7
5 6 7 8
1 2 3 4
2.2 USABLE DISCS AND USB DEVICES
8 CDJ-850
1 2 3 4
5 6 7 8
CDJ-850 9
5 6 7 8
1 2 3 4
2.3 PANEL FACILITIES
10 CDJ-850
1 2 3 4
5 6 7 8
CDJ-850 11
5 6 7 8
1 2 3 4
12 CDJ-850
1 2 3 4
5 6 7 8
3. BASIC ITEMS FOR SERVICE

3.1 CHECK POINTS AFTER SERVICING
Items to be checked after servicing / CDJ A
To keep the product quality after servicing, confirm recommended check points shown below.
No. Procedures Check points
Confirm whether the customer complain has been solved. The customer complain must not be reappeared.
1 If the customer complain occurs with the specific disc, use it for Audio and operations must be normal.
the operation check.
2 Check output analog audio. Audio and operations must be normal.
3 Play back a CD. (track search) Audio, Search and operations must be normal.
Check the connection of each interface.

B
4 Play back data contained in the device connected to USB A. Audio, Search and operations must be normal.
USB B The device must be recognized by the PC.
Check output signals while the JOG dial or TEMPO slider is Audio and operations must be normal.
5
being operated.
Check the appearance of the product. No scratches or dirt on its appearance after receiving it for
6
service.
See the table below for the items to be checked regarding video and audio.
Item to be checked regarding audio
C
Distortion
Noise
Volume too low
Volume too high
Volume fluctuating
Sound interrupted
3.2 JIGS LIST D
Jigs List
Jig Name Part No. Purpose of use / Remarks
CD test disc STD-905 CD playback diagnosis
Lubricants and Glues List
Name Part No. Remarks

Refer to “9.4 JOG DIAL SECTION”, E
Lubricating oil GYA1001 “9.5 SLOTIN MECHA SECTION”.
Lubricating oil ZLB-HFD1600 Refer to “9.4 JOG DIAL SECTION”.
Dyfree GEM1036 Refer to “9.5 SLOTIN MECHA SECTION”.
Cleaning
Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools.
Position to be cleaned Name Part No. Remarks
Pickup lenses Cleaning liquied GEM1004 Refer to F
Cleaning paper GED-008 "9.5 SLOTIN MECHA SECTION".
CDJ-850 13
5 6 7 8
1 2 3 4
3.3 PCB LOCATIONS
G DFLB ASSY H KSW1 ASSY F USBA ASSY E CMPX ASSY

• Bottom view
PSWB M
ASSY
D MAIN
SLD1 L ASSY
ASSY
C JINT
ASSY
JFLB J
ASSY
SLD2 N
ASSY
C
K JOGB ASSY I KSW2 ASSY
SLOTIN MECHA ASSY

P ACIN ASSY
B SLMB ASSY
A CNCT
ASSY
TM ASSY-S
D
(VTM091)
O POWER SUPPLY ASSY
NOTES: - Parts marked by “NSP” are generally unavailable because they are not in our Master Spare Parts List.
- The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Mark No. Description Part No. Mark No. Description Part No.
LIST OF ASSEMBLIES
1..MAIN ASSY DWX3174 2..JOGB ASSY DWX3155
E 2..ACIN ASSY (SYXJ8, FLXJ, KXJ5, AXJ5) DWX3158
NSP 1..SUB1 ASSY (SYXJ8, FLXJ, KXJ5, AXJ5) DWM2399 2..ACIN ASSY (CUXJ) DWX3173
NSP 1..SUB1 ASSY (CUXJ) DWM2405
NSP 2..KSW1 ASSY DWS1422 NSP 1..SUB2 ASSY DWM2400
NSP 2..SLD1 ASSY DWS1423 2..CNCT ASSY DWX3151
2..PSWB ASSY DWS1424 2..CMPX ASSY DWX3153
2..USBA ASSY DWX3156
2..SLMB ASSY DWS1425 2..JINT ASSY DWX3157
2..KSW2 ASSY DWS1426
2..SLD2 ASSY DWS1427 > 1..POWER SUPPLY ASSY DWR1463
2..DFLB ASSY DWX3152 ∗
2..JFLB ASSY DWX3154 NSP 1..SLOTIN MECHA ASSY DXA2206
F 1..TM ASSY-S (VTM091) DXX2616
∗ The service part of DFLB Assy (DWX3152) is supplied with KSW1 Assy (DWS1422) and SLD1 Assy (DWS1423).
(There assemblies are connected with the jumper wires.)
14 CDJ-850
1 2 3 4
5 6 7 8
CDJ-850 15
5 6 7 8
1 2 3 4
4. BLOCK DIAGRAM
4.1 OVERALL WIRING DIAGRAM
A
DE010VE0
Length=100mm
Earth Lead Cable
CN2301
Pitch=1.0mm
Horizontal DKN1312-A Reverce Face
Contact Side Down FFC
VCC 12 12 VCC Soldered
U+ 11 11 U+
U- 10 10 U-
(DXA2206)
AC POWER CORD
SPINDLE MOTOR
V+ 9 9 V+
V- 8 8 V- ADG7022 (For CUXJ)
W+ 7 7 W+ ADG7097, ADG1154 (For FLXJ)
W- 6 6 W- ! XDG3054 (For KXJ5)
HB 5 5 HB ADG1154 (For SYXJ8)
NEUTRAL
U 4 4 U ADG7079 (For AXJ5)
LIVE
V 3 3 V
W 2 2 W
INSW 1 1 INSW
DDD1535- DDD1491- JA2401
2
1
Pitch=0.5mm Pitch=0.5mm DKP3891: CUXJ
SLOTIN MECHA ASSY

CN2302
Length=80mm CN2502 CN2501
Length=175mm Horizontal DKP3889: OTHERS
P
DKN1445-A
TM ASSY-S (DXX2616)
DKN1445-A DKN1445-A
Horizontal Reverse Face FFC Reverse Face FFC Contact Side Down
Contact Side Down FR 24 24 FR Horizontal FR 1 1 FR
B
FD 23
TR 22
23 FD
22 TR
Contact Side Down FD
TR
2
3
2
3
FD
TR ACIN ASSY Verti
(DWX3173: CUXJ)
TD 21 21 TD TD 4 4 TD
ASSY
GNDS 20
LD780 19
20 GNDS
19 LD780 (DWX3151) NC
GNDS 6
5 5
6
NC
GNDS
GNDS 18
GNDS 17
18 GNDS
17 GNDS
LD650 7
PD 8
7
8
LD650
PD (DWX3158: OTHERS)
Boardin
I
GNDS 16 16 GNDS LD780 9 9 LD780
GNDS 15 15 GNDS GNDS 10 10 GNDS
VR780 11 11 VR780
A CNCT
VR780PD 14 14 VR780PD
13 GNDS VRCOM 12 12 VRCOM
DKP3870-
GNDS 13
GNDS 12 12 GNDS VR650 13 13 VR650 Pitch=3.96mm
KSW2
09SD PICK UP ASSY

A 11 11 A A 14 14 A Length=100mm
C B 10 10 B B 15 15 B Connector Ass'y
GNDS 9
GNDS 8
9 GNDS
8 GNDS SW1_DVD/CD 17
VRF 16 16 VRF
17 SW1_DVD/CD CN1 Vertical (DWS
O
NEUTRAL(BLUE) 2
LIVE(PURPLE) 1
C 7 7 C C 18 18 C B2P3-VH VH
JINT ASSY !
D 6 6 D D 19 19 D
E 20 20 E
E 5 5 E D20PDY07
VREF 4 4 Vcc 21 21 Vcc
VREF Pitch=2.0m
(DWX3157) F 3
V+5P 2
3 F
2 V+5P
VREF 22
F
GNDS 24
23
22 VREF
23 F
24 GNDS
POWER SUPPLY Length=20
Parallel Ju
GNDS 1 1 GNDS
Horizontal
CN2304
DKN1288-A
1 ST1-
ASSY
(DWR1463)
ST1- 1
Contact Side Up ST1+ 2 2 ST1+ STEPPING
ST2+
ST2+ 3 3
ST2- 4 4
ST2- MOTOR
C Soldered 1 GNDM
Pitch=1.0mm 2 GNDD
DDD1527- Same Face 3 PWR_XON

FPC LO+ LOADING MOTOR 4 V+12
Vertical Pitch=1.0mm ASSY-S 5 V+12
Contact Side Length=180mm LO- (DXX2615) 6 V+12_EUP
Same Face
CN2303
FFC CN1701
B SLMB ASSY ZWNN1007G28-9-06A

B6B-XH-A
1
2
3
4
5
VKN1374-A VKN1265-A CN2
Length=60mm ZWNN1007G28-8-06A
V+6R6
GNDD
CUE_LED
CUE_SW
PLAY_LED
Vertical
LPS2
LPS1
GNDD 3
1
2
1 LPS2
2 LPS1
3 GNDD
(DWS1425) White Single Wire
LO+
Length=60mm
Gray Single Wire
DKP3869-
LO+ 4 4 LO+
Horizontal LO- Pitch=2.5mm
LO- 5 5 LO-
Contact Side Up Length=100mm
Connector Assy
DDD1536-(Gold) Horizontal Horizontal
DDD1523-
Pitch=1.0mm Vertical
KSW1 A
Horizontal C N 2 3 0 5 Pitch=0.5mm Length=70mm Contact Side CN2001
(DWS1
1
2
3
4
5
6
CN201 Contact Side Down Contact Side Up CN402 B6B-XH-A
Contact Side Down D K N 1 4 0 7 - ALength=66mm Same Face CN2002
GNDM
GNDD
PWR_XON
V+12_EUP
DKN1404-A
V+12
V+12
RKN1068-A VKN1258-A
Reverse Face FFC FFC
INSW 1 50 INSW
GNDD 27 1 GNDD Vertical US
H
W 2 49 W
V+12_EUP 26 2 V+12_EUP
W 3 48 W
GNDD 25 3 GNDD
V 4 47 V
GNDD 24 4 GNDD
V 5 46 V
V+5R6 23 5 V+5R6
U 6 45 U
V+5R6 22 6 V+5R6
U 7 44 U
GNDD 21 7 GNDD
GNDD 8 43 GNDD
TSCK 20 8 TSCK
HW- 9 42 HW-
D HW+ 10 41 HW+
GNDD 19 9
10
GNDD
PNL_XBUSY
PNL_XBUSY 18
HV- 11 40 HV-
TSO 17 11 TSO
HV+ 12 39 HV+
MAIN_XBUSY 16 12 MAIN_XBUSY
HU- 13
D
38 HU-
TSI 15 13 TSI
HU+ 14 37 HU+
MAIN_XRST 14 14 MAIN_XRST
V+5M 15 36 V+5M
GNDD 13 15 GNDD
GNDD 16 35 GNDD
MAIN_XMUTE 12 16 MAIN_XMUTE
FR 17 34 FR
GNDD 11 17 GNDD
D 1/4- D 4/4
FD 18 33 FD
VDET 10 18 VDET
TR 19 32 TR
GNDD 9 19 GNDD
TD 20 31 TD
PWR_ON 8 20 PWR_ON
GNDS 21 30 GNDS
GNDD 7 21 GNDD
LD780 22 29 LD780
22 USB_VBUSON
MAIN ASSY
USB_VBUSON 6
GNDS 23 28 GNDS GNDD 5 23 GNDD
PD 24 27 PD
USB_CODETFLG 4 24 USB_CODETFLG
A_A 25 26 A_A
(DWX3174)
GNDD 3 25 GNDD
A_B 26 25 A_B
USBA_D_N 2 26 USBA_D_N
A_C 27 24 A_C
USBA_D_P 1 27 USBA_D_P
A_D 28 23 A_D
DDD1522-
A_S1 29 22 A_S1
Vertical Pitch=1.0mm
VREF 30 21 VREF Horizontal Length=170mm
A_S2 31 20 A_S2 Contact Side Up Contact Side Vertical
V+5P 32 Contact Side Same Face
19 V+5P
GNDA 17 1 GNDA FFC
GNDS 33 18 GNDS ROUT 16 2 ROUT
GNDS 34 17 GNDS TSO 1
GNDA 15 3 GNDA
GNDS 35 16 GNDS PNL_XBUSY 2
LOUT 14 4 LOUT
LPS1 36 15 LPS1 TSI 3
E LPS2 37 14 LPS2
GNDA 13
GNDD 12
5 GNDA
6 GNDD
GNDD 4
GNDS 38 13 GNDS TSCK 5
GNDD 11 7 GNDD
GNDD 6
LO- 39 12 LO-
CONT1 10 8 CONT1
PNL_CNVSS 7
LO- 40 11 LO- GNDD 9 9 GNDD
GNDD 8
LO+ 41 10 LO+
CONT2 8 10 CONT2
PNL_XRST 9
LO+ 42 9 LO+ GNDD 7 11 GNDD
ST2+ 43 8 ST2+ MAIN_XBUSY 10
USB_D_N 6 12 USB_D_N
USB_STOP 11
ST2+ 44 7 ST2+
USB_D_P 5 13 USB_D_P
MAIN_XRST 12
ST2- 45 6 ST2- GNDD 4 14 GNDD
ST2- 46 5 ST2- PWR_ON 13
VBUS_B 3 15 VBUS_B
ST1+ 47 PNL_XMUTE 14
V+7R6_M
4 ST1+
V+7R6_D
V+7R6_D
GNDD 2 16 GNDD
13 V+10_A
VDET 15
11 V-10_A
ST1+ 48
GNDM
3 ST1+
GNDD
GNDD
GNDD
GNDD
10 GNDD
12 GNDA
GNDD 1 17 GNDD
V+12
ST1- 49 2 ST1-
Horizontal DDD1524- GNDD 16
ST1- 50 1 ST1- CN403
RKN1058-A
Pitch=1.0mm CN2006 V+12 17
CN401 VKN1248-A
Length=70mm V+12 18
1
2
3
4
5
6
7
8
9
AKM1299-A
Same Face GNDD 19
V+12_EUP 20
FFC
GNDD 21
V+10_A 13 CN2003
GNDA 12 PF13PP-S07 VKN1252-A
E E 1/2, E 2/2
V-10_A 11 Pitch=2.0mm
GNDD 10 Length=75mm
V+12 9 Connector Ass'y
GNDD 8 V+5_USB 1 1 V+5_USB
V+7R6_D 7 USBA_D_N 2 2 USBA_D_N
CMPX ASSY
V+7R6_D 6 USBA_D_P 3 3 USBA_D_P
F GNDD 5
GNDD 4
GNDD 4
GNDD 5
4 GNDD
5 GNDD
(DWX3153)
GNDD 3
CN2005 D20PDY0510E JH2201
GNDM 2 52147-0510 Pitch=2.0mm 51048-0500
V+7R6_M 1 Vertical Length=100mm Vertical
CN2004 Vertical Parallel Jumper
KM200N A13 Wire
16 CDJ-850
1 2 3 4
5 6 7 8
A
- When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".

- : The power supply is shown with the marked box.
r FLXJ)
JOGB ASSY
K (DWX3155)
Horizontal
Contact Side Up
CN1801
CKS1072-A
Horizontal Vertical
CN1901 JH1801
JOG_SW 1
NC 2
SHEET SW
51048-0400
52151-0410
GNDD 3 (DSX1078)
P Vertical
CN1401
52147-0710
V+3R3_SW
JOG2
JOG1
GNDD
1
2
3
4
1 JOG2
2 JOG1
3 V+3R3_SW
4 GNDD
B
KEY2_B 7
PLAY_SW 6
D20PYY0405E
PLAY_LED 5
Pitch=2.0mm
RS) CUE_SW
CUE_LED
4
3
Length=50mm
Parallel Jumper Wire
I GNDD 2
V+6R6 1
KSW2 ASSY N SLD2 ASSY

(DWS1427)
(DWS1426) J JFLB ASSY CN1501
52147-0410
! D20PDY0720E
(DWX3154) 4 V+3R3_EUP
3 GNDA
Pitch=2.0mm
LY
2 ADIN
Length=200mm 1 ADCT
Parallel Jumper Wire
Vertical
D20PDY0410E
1 V+3R3_SW
7 JOG_SW
Pitch=2.0mm
4 J_SCLK
6 J_DSO
3 J_LAT
2 GNDD
10 GNDD
12 GNDD
Length=100mm C
8 JOG2
9 JOG1
J_BK
11 V+38
13 V+12
Vertical
Contact Side Up Parallel Jumper Wire
CN1802
5
VKN1244-A
JH1301
JH1201 51048-0400 Vertical
1
2
3
4
5
6
7
51048-0700
1 ADCT
V+6R6
GNDD
CUE_LED
CUE_SW
PLAY_LED
PLAY_SW
KEY2_B
Vertical DDD1521- 2 ADIN

Pitch=1.0mm 3 GNDA
Length=120mm 4 V+3R3_EUP
Same Face
mm FFC
ssy
KSW1 ASSY
(DWS1422) CN1002
J_SCLK 10
J_LAT 11
GNDD 12
V+3R3_SW 13
L
1
GNDD 2
3
GNDD 4
5
6
JOG_SW 7
J_DSO 8
9
Jumper Wire VKN1273-A

Horizontal
JOG1
JOG2
J_BK
V+12
V+38
SLD1 ASSY
USB_ACT_LED USB_ACT_LED
H USB_STOP USB_STOP
Contact Side Up
1KEY_SW 1KEY_SW
2KEY_SW
4KEY_SW
2KEY_SW
4KEY_SW (DWS1423)
8KEY_SW 8KEY_SW Jumper Wire
1KEY_LED 1KEY_LED
PWR_SW PWR_SW
2KEY_LED 2KEY_LED GNDA GNDA
4KEY_LED
8KEY_LED
4KEY_LED
8KEY_LED
ADIN ADIN D
ADCT ADCT
REV_LED REV_LED V+3R3_EUP V+3R3_EUP
SHIFT_SW SHIFT_SW MT_LED MT_LED
REV_SW REV_SW V+6R6 V+6R6
KEY2_B KEY2_B VINYL_LED VINYL_LED
PLAY_SW PLAY_SW KEY0 KEY0
PLAY_LED PLAY_LED GNDD GNDD
CUE_SW CUE_SW TCH/REL TCH/REL Vertical
CUE_LED CUE_LED EJECT_LED EJECT_LED JH1302
GNDD GNDD 51048-0300
EUP_LED EUP_LED
V+6R6 V+6R6 GNDD 3
GNDD 2
PWR_SW 1
DDD1522-
Pitch=1.0mm
Length=170mm
G D20PDY0310E
Pitch=2.0mm
Length=100mm
Same Face
FFC
Vertical
Contact Side DFLB ASSY Parallel Jumper Wire
CN1601
(DWX3152)
2
3
1
21 TSO
52147-0310
20 PNL_BUSY
PWR_SW
GNDD
GNDD
Vertical
19 TSI
18 GNDD E
17 TSCK
16 GNDD
15 PNL_CNVSS
14 GNDD
13 PNL_XRST
12 MAIN_XBUSY
11 USB_STOP
10 MAIN_XRST
M PSWB ASSY
9 PWR_ON
8 PNL_XMUTE
7 VDET
6 GNDD
5 V+12
4 V+12
(DWS1424)
3 GNDD
2 V+12_EUP
1 GNDD
CN1001
VKN1252-A
1 V+5_USB
2 USBA_D_N
F
USBA ASSY
3 USBA_D_P
4 GNDD
5 GNDD
F
20PDY0510E
tch=2.0mm
JH2201
51048-0500
(DWX3156)
ngth=100mm
4
3
2
1
Vertical
arallel Jumper
RT1
RT2
JA2201
re DKB1106-1
CDJ-850 17
5 6 7 8
1 2 3 4
4.2 SIGNAL BLOCK DIAGRAM
A P ACIN ASSY I
CN2301 W,V,U,HB,W-,W+,V-,V+,U-,U+ OEIC
INSW JA2401
1 1
SPINDLE PICKUP ASSY

CN2302 CN2502 CN2501 MOTOR
FR,FD,TR,TD
VR780PD,A,B,C,D,E,F
LD780 LD780
1 1 9 9
CN2304
SHORT
SW A CNCT ASSY O
B ST1+,ST1-,ST2+,ST2-
M STEPPING
MOTOR
POWER SUPPLY
CN2303
ASSY
LO+,LO- LOADING
LPS2
M MOTOR
1 1 CN140
LPS1
2 2
CN1701
B SLMB ASSY
CN2305
3
JH120
CN201 LPS1
3
36 15 135 CN2001
CN2004
LPS2
CN401
37 14 134
PWR_XON
INSIDE USB_X2
1 50 136 94 3 X102
C
VR780PD,
22 29
LDO
41 TCOUNT,
ADC 208
93
USB_X1
1 48MHz
X-tal
E CMPX ASSY
A,B,C,D,E,F 113 EXTAL
IC201 56 1 X101
SRVSCLK,
FR,FD,TR,TD SERVO X-tal
SRVLRCK, XTAL
DSP 55 3 33MHz
SRVSDATA K
IC103
D
73
CN2002
CN402
SRVBCLK,SRVBUS0-3, MAIN CPU

SRVSBSY,SRVCCE,
CLK: 33 MHz
SRVRST
LO+,LO-
CORE CLK:
200 MHz MAIN ASSY
TSO
IC204 66 17 11
ST1+,ST1-, DRIVER TSI
ST2+,ST2- SPDLFG 64 15 13
43 181 SCIF TSCK
48 20 8
W,V,U,HB,W-,W+, PNL_XBUSY
V-,V+,U-,U+ 70 18 10
MAIN_XBUSY
75 16 12
DRVMUTE1, MAIN_XRST
D DRVMUTE2, 59 14 14
PWMLO,
PWMSL1IN, VDET
POWER DETECT 10 18
C
PWMSL2IN PWR_ON
CIRCUIT 20
8
USB_VBUSON
H
88 6 22 4 IC2003
JINT ASSY IC101 USB_CDETFLG USB_CODETFLG USB OVER V+5_USB
System Bus (Bus CLK:66MHz)
32M
FLASH ROM
16 71
160
MUTE
4
12
24
16
MAIN_XMUTE
5 CURRENT
PROTECT
KS
1
USBA_D_N
16
DP 6 2 26 3
USB 101 3 USBA_D_P
Full Speed DM 2 1 27 5
100 5
I/F 2
IC102 87 10 USBB_D_N
256M 16 USB_ABSEL 7 6 12 10
SDRAM IC107 USBB_D_P
USB SW 1 5 13 12
VBUS VBUS_B
102 3 15
E 15
BCK, DSPCS,DSPRST,PLAY CONT1
LRCK, 149 10 8 13
DATA_L, CONT2
AUDIO_SCK, 161 185 150 8 10
DATA_R PNL_XMUTE
AUDIO_SI,
AUDIO_SO DACCS ZERO 14
ALO LOUT
15 11 7 3 1 14 4 CN2003
ARO ROUT MUTE
IC301 8 5 7 16 2 CIRCUIT
DSP CLK11M
CN2006
CN403
73 16 3 2 1 CN2005
IC302 IC303
DAC OP AMP
CONT2
CONT1
45
ROUT
DACBCLK,
LOUT
DACBCLK, JH2201
CLK_A_16M
CLK_S_16M
DACBCLK V+5_USB
1
USBA_D_N
2
USBA_D_P
3
10 2
X103
IC105 5 JA2003
F X-tal
Buffer 16.9344 USB Type A
6
F
MHz JA2003 JA2002 JA2001 CONNECTOR
AUDIO OUT CONTROL USB Type B
CONNECTOR
USBA
18 CDJ-850
1 2 3 4
5 6 7 8
I KSW2 ASSY K JOGB ASSY

A
CN1901 JOG2
1 1
PC1901 JOG1
2 2
ENCODER
3 4
JH1801 CN1801
1 SHEET SW
JOG_SW
N SLD2 ASSY
VR8701
J JFLB ASSY TEMPO SLIDER
Y KEY,LED V1801
26 27 25 24
B
JOG_SW
JOG FL ADIN
JOG2
JOG1
J_SCLK
ADCT
J_DSO
J_LAT
J_BK
CN1401 3 4 5 6 7
3 4 5 6 8 9 7 CN1802
3 4 5 6 7
JH1201 11 10 9 8 6 5 7 2 1 CN1501
CN1002
G DFLB ASSY
PLAY_LED
PLAY_SW
CUE_LED
JOG_SW
CUE_SW
KEY2_B
J_SCLK
JOG2
JOG1
J_DSO
J_LAT
2 1 JH1301
J_BK
JUMPER KEY,LED
KEY2 21 23 28 24 25 26 27 JUMPER
83
PLAY_SW ADIN
60 2
PLAY_LED ADCT
58 1 C
CUE_SW
61
CUE_LED KEY0 KEY0
59 87
EUP_LED1 EUP_LED
USB_STOP 92
KEY,LED 57 EJECT_LED EJECT_LED
USB_ACT_LED 93
75 VINYL_LED VINYL_LED
94
MT_LED MT_LED
8KEY_SW 95
71
4KEY_SW
72 TCH/REL TCH/REL
2KEY_SW 88
73
1KEY_SW
74
PWR_SW VR1301
8KEY_LED 90
67 TOUCH/RELEASE
4KEY_LED
68 KEY4
2KEY_LED 86 KEY,LED
69 UTILITY_LED
1KEY_LED 82
70 INFO_LED
SHIFT_SW 81 D
65 IC1007 PLAYLIST_LED
REV_SW 80
63 PANEL CPU BROWSE_LED
REV_LED
66
CLK: 15.975 MHz
79
84
KEY3
KEY,LED
L
H KSW1 ASSY
78
77
PC_LED
USB_LED
DISC_LED
SLD1
ASSY
TSO 76
21 32
TSI
19 31 KEY1 KEY,LED
TSCK 85
17 33
PNL_XBUSY
20 34 LOOPIN_SW
MAIN_XBUSY 56 KEY,LED
12 42 LOOPOUT_SW
MAIN_XRST 54
10 40 RELOOP_SW
51
IN_LED
VDET 55
PWR_SW
7 44 OUT_LED E
PWR_ON 53
9 45 RELOOP_LED
52
PNL_XMUTE
8 43 1 JH1302
ENC_1
CN1001
5
ENC_2
POWER DETECT 4
ENC_SW
CIRCUIT 35 37 39 38 15 13 12 3
D_SCLK
D_LAT
D_DSO
V1001
D_BK
XIN XOUT
S1018
PNL_XRST
DATA FL ROTARY SW
30 31 32 33 X1001 4
X-tal IC1004
15.975 MHz RESET IC
1 CN1601
PWR_SW
3 F
M
eA
F
TOR
USBA ASSY
PSWB ASSY
CDJ-850 19
5 6 7 8
1 2 3 4
4.3 POWER SUPPLY BLOCK DIAGRAM
A
P ACIN ASSY I K
CN2301 OEIC
JA2401
VCC
12 12
SPINDLE PICKUP ASSY

CN2302 CN2502 CN2501 MOTOR
VREF VREF 2 1
4 4 22 22
POWER
2
V+5P
2 21
VCC
21
O SUPPLY
CN2304 A CNCT ASSY
STEPPING
ACDC ASSY
B M MOTOR
CN2303
LOADING
M MOTOR
CN140
CN1701 B
SLMB ASSY 3 4 5 6
JH120
CN2004
CN2001 3 4 5 6
CN401
D E
V+12_EUP
CMPX ASSY
PWR_XON
MAIN ASSY
H
V+12
V+7R6_M V+7R6_M V+7R6 IC2001
CN2305
1 1
CN201
DCDC
IC204
C DRIVER V+5R6_M IC206
REGULATOR V-11_A
12V→7.6V
12V→-11V KSW
7.6V→5.6V
V+5P V+5P IC405 V+5R6 IC409 V+7R6_D V+7R6_D
32 19 REGULATOR DCDC 6 6
V+5M V+5M 5.6V→5V 7.6V→5.6V
15 36 7 7
VREF V+3R3_S IC408

IC201
30 21 SERVO DSP
REGULATOR
5.6V→3.3V
VREF1R65 V+1R2 V-10_A V-10_A Q2028
V+3R3 REGULATOR
11 11
IC404 IC401 -11V→-10V
REGULATOR REGULATOR
IC103 3.3V→1.2V 5.6V→3.3V
MAIN CPU
V+10_A V+10_A Q2028

13 13 REGULATOR P2003
IC101 12V→10V
32M PROTECTOR
FLASH ROM (0.5A)
V+12 V+12
9 9
IC102
D C 256M
SDRAM
JINT IC107
USB SW PROTECTOR
ASSY (0.375A)
P2004
CN2002
CN402
IC105
Buffa
V+3R3_A IC402
REGULATOR V+12_EUP V+1
IC301 5.6V→3.3V 26 2 20
DSP IC403 V+
REGULATOR PWR_ON 18
3.3V→1.25V 8 20 V+
17
V+1R25
V+5R6 IC2002
IC302 23 5 REGULATOR PW
DAC IC406 V+10_A 5.6V→5V 13
REGULATOR 22 6
10V→5V
VDET VD
V+5_A 10 18 15
IC303
E V-10_A
CN2003
OP AMP
V+12_EUP
VDET
V-11_A
IC2003
USB OVER CURRENT
PROTECT (1A)
V+5_USB
POWER DETECT CIRCUIT MUTE

CIRCUIT
1 CN2005
CN2006
CN403
JH2201
V+5_USB
1
JA2003
F USB Type A
JA2003
AUDIO OUT
JA2002 JA2001
CONTROL USB Type B
CONNECTOR
CONNECTOR
F USBA AS
20 CDJ-850
1 2 3 4
5 6 7 8
I KSW2 ASSY K JOGB ASSY

A
CN1901
PC1901 V+3R3_SW
ENCODER 3 3
J JFLB ASSY
3 JH1801 CN1801
V+3R3_SW
1
SHEET SW
IC1803 V+27
1
OWER
DCDC
12V→27V
V+27_SW
N SLD2 ASSY
UPPLY IC1802
DCAC
12V→AC2.7V
VFDP2R7_F1
38
VR8701
TEMPO SLIDER
SSY V+3R3_SW
23
LED V+38 B
V1801
V+3R3_SW
V+6R6
V+3R3_EUP
V+38
V+12
JOG FL
CN1401 1
CN1802
13 1 11
1
JH1201 1 13 3 CN1002 4 CN1501
G DFLB ASSY
V+6R6
4
JH1301
JUMPER LED
H
JUMPER
V+6R6
V+3R3_EUP
KSW1 ASSY C
V+12_EUP IC1006 V+3R3_EUP V+3R3_EUP IC1007 PWR_SW
DCDC
PANEL CPU
12V→3.3V
Q1018 V+3R3_SW
LED FET SW
PWR_ON
V+38
VDET
IC1004
RESET IC
PWR_ON
V+6R6
VR1301
TOUCH/RELEASE
LED
V+12 IC1006 V+6R6 V+6R6
DCDC
12V→6.6V
D
LED L
SLD1
ASSY
V+12_EUP
2
V+12 LED
4
V+12
5
LED
PWR_ON
9
VDET
7
PWR_SW
VDET
E
CN1001
1 JH1302
POWER DETECT CIRCUIT V+3R3_EUP
V+6R6_FL
V1001 S1018
ROTARY SW
DATA FL
V+3R3_SW
1
2
1 CN1601
V+38
PWR_SW
3
34
35
F
F USBA ASSY M
PSWB ASSY
CDJ-850 21
5 6 7 8
1 2 3 4
5. DIAGNOSIS
5.1 POWER ON SEQUENCE
A
AC IN (Plugging of the AC power cord)
Power supply (V+12_EUP, V+3R3R_EUP) to the Panel CPU starts.
Reset IC (IC1004) IC1004 (Pin 4): The Reset signal is sent to the Panel CPU (IC1007).
IC1007 (Pin 12): Receives the Reset signal.

Panel CPU
(IC1007) STANDBY mode is entered.
*FL display: Unlit.
POWER ON (Turn on the POWER switch.)
STANDBY mode is shifted to POWER_ON mode.

“POWER ON” is displayed on the FL display.
B
Panel CPU
(IC1007) IC1007 (Pin 45): Power supply to the Main CPU (IC103) starts.
IC1007 (Pin 40): The Reset signal is sent to the Main CPU (IC103).
IC103 (Pin 59): Receives the Reset signal.
The program is downloaded to IC301 (Audio DSP).

Main CPU
(IC103) IC103 (Pin 158): The Reset signal is sent to the Audio DSP (IC301).
IC103 (Pin 69): The Reset signal is sent to the Servo DSP (IC201).
Main CPU (IC103) Communication between the Main CPU (IC103) and If communication fails, “E–8709” will be
C
Panel CPU (IC1007) Panel CPU (IC1007) starts. displayed on the FL display.
Audio DSP (IC301) IC301 (Pin 47): Receives the Reset signal.
Servo DSP (IC201) IC201 (Pin 90): Receives the Reset signal.
Checking the inside SW
LD (Laser Diode) ON
Adjustment of tracking and focus offset
Spindle kick, focus sweep, and focus ON If the first check fails, measure the level of the S-shaped
waveform while the pickup lens is descending.
D
Checking if focus is OK If the level of the S-shaped waveform is 0.88 Vp-p or less,
focusing is turned ON with RF gain increased.
Acceleration of spindle (200 ms) If checking fails three times, “EJECT” will be
displayed on the FL display.
CLV servo ON
CD drive Waiting 300 ms
Tracking balance adjustment (Tracking open)
Tracking close
E
GFS (RF lock) check
Focus balance adjustment
Focus gain adjustment
Tracking gain adjustment

TOC reading RF gain adjustment After TOC reading is completed
Depending on the accuracy
of the stepper, the TOC If the pickup is reading the
position memory will be program area, it will jump
located after the unit is to the TOC area.
turned ON.
F
The first track is searched for.
Playback (Muting OFF)
22 CDJ-850
1 2 3 4
5 6 7 8
5.2 TROUBLESHOOTING
In this section, causes of failure, diagnostics points, and corrective measures can be searched for according to symptoms. A
Before disassembling this unit, it is recommended to infer a failure point by referring to the error code.
For the relationship of each power-supply and signal system, see “4.3 POWER SUPPLY BLOCK DIAGRAM.”
If software of the product is updated before performing diagnostics, check that software updating has been performed properly
before proceeding to diagnostics.
If software updating has not been performed properly, update the software, following the instructions in “8.3 UPDATING OF
THE FIRMWARE.”
Contents
[0] Prior Confirmation
[1] Failure in Startup
[2] Display (DATA FL/JOG FL/LED) B
[3] Operations (SW/Volume/JOG)

[4] USB (USB-Type A), PC (USB-Type B)
[5] AUDIO OUT
[6] CONTROL
[7] DRIVE Assy
[8] SERVICE MODE
[9] Error Codes
[10] Basic Operation Check of CPU/DSP
The waveform numbers described in this section correspond to the “10.14 WAVEFORMS.”
C
[0] Prior Confirmation
[0-1] Checking in Service Mode
No. Cause Diagnostics Point Item to be Checked Corrective Action Reference
See the section describing locations of defects in 6. SERVICE
1 — Service mode Check the failure points.
this manual. MODE
[0-2] Checking Cables

Disconnection, Check that all the cables are securely 4.1 OVERALL
breakage, or connected. Securely connect the cables. If a cable is broken,
1 Cables CONNECTION
loose connection Check that there is no breakage in the replace it. D
DIAGRAM
of cables cables.
[1] Failure in Startup

[1-1] No power
Plug the AC power cord in and even if turn the power on, the product does not startup.
CMPX Assy If the V+12_EUP voltage is not output, the POWER 4.3 POWER SUPPLY
Standby power DFLB Assy Check the voltages of V+12_EUP and SUPPLY Assy may be defective. BLOCK DIAGRAM
1
failure POWER V+3R3_EUP. If the V+12_EUP voltage is output, the DFLB Assy 10.13 VOLTAGES
SUPPLY Assy may be defective. 1 18
E
DFLB Assy Check if there is loose connection on the If the connection up to the Power switch is properly 10.15 EACH
Path failure of made and if the PWR_SW signal is not set to "L" SIGNAL LEVEL
2 SLD1 Assy signal line from the Power switch (S1601)
the power switch when the Power switch is pressed, the Power switch
PSWB Assy to PANEL CPU (IC1007). A
may be defective.
If the PWR_ON is "L", PANEL CPU(IC1007) may be 10.15 EACH

Path failure of DFLB Assy Check the level of PWR_ON (IC1007-pin defective.
3 45) and PWR_XON (CN2001-pin 3) signals. If the PWR_XON is "H", poor connection or Q2021 SIGNAL LEVEL
the power on CMPX Assy
B J
may be defective.
CMPX Assy Check the V+12 voltage of CN2001-pins If the voltage is not output, POWER SUPPLY Assy
4 Power failure POWER 10.13 VOLTAGES
4 and 5. may be defective. 2
SUPPLY Assy
CDJ-850 23
5 6 7 8
1 2 3 4
A [1-2] Mode shift error in Standby mode

Shifting to the STANDBY mode cannot be performed even if turn the power off.
DFLB Assy Check if there is loose connection on the If the connection up to the Power switch is properly
Path failure of 10.15 EACH
1 SLD1 Assy signal line from the Power switch (S1601) made and if the PWR_SW signal is not set to "H"
the power switch SIGNAL LEVEL
PSWB Assy to PANEL CPU (IC1007). when the Power switch is turned off, the Power switch A
may be defective.
If the PWR_ON is "H", PANEL CPU(IC1007) may be
Check the level of PWR_ON (IC1007-pin 10.15 EACH
2 Path failure of DFLB Assy defective.
45) and PWR_XON (CN2001-pin 3) signals. SIGNAL LEVEL
the power on CMPX Assy If the PWR_XON is "L", poor connection or Q2021
may be defective. B J
B [1-3] “E-8709” is displayed on the DATA FL display after startup.

Communication between the Main CPU and Panel CPU has not been established.
If no signal is output, the possible causes are poor 10.14
Communication connection, failure in the PANEL CPU (IC1007) or WAVEFORMS
DFLB Assy Check the TSCK, TSI, PNL_BUSY, TSO and
1 failure between MAIN CPU (IC103), and startup failure of the 8 9 7 10
MAIN Assy MAIN_BUSY waveforms.
the microcomputer MAIN CPU caused by defective FLASH ROM
4
(IC101) or SDRAM (IC102).
Check the V+3R3 and V+1R2 power If power is not output, a part of the power supply 10.13 VOLTAGES
2 Power failure MAIN Assy
voltages. section may be defective. 9 10
[1-4] The Standby LED flashes in red.

C
A voltage error 5.5 ABOUT POWER
If the signal level is "L", a voltage error was
1 was generated. — Check the level of the VDET signal. SUPPLY MONITORING
generated.
10.13 VOLTAGES
[2] Display (DATA FL/JOG FL/LED)

[2-1] The DATA FL does not light.
If the presence of power is not confirmed, check the 4.3 POWER SUPPLY
D Check the power-supply voltages mounting statuses of the regulator IC and its BLOCK DIAGRAM
1 Power failure DFLB Assy
(V+6R6,F±, V+38, V+3R3_SW) of the FL. peripheral parts for each power supply. If they are 10.13 VOLTAGES
properly mounted, then the parts may be defective. 20 21 23 19
Check the waveforms and connection of

communication line of FL in the DFLB Assy. If no signal is output, the PANEL CPU (IC1007) may 10.14
• D_SCLK be defective. WAVEFORMS
2 Signal errors DFLB Assy
• D_SO If output signal is no problem, DATA FL (V1001) may 1 4 3 2
• D_LAT be defective.
• D_BK
[2-2] The JOG FL does not light.

If the presence of power is not confirmed, check the 4.3 POWER SUPPLY
E Check the power-supply voltages
mounting statuses of the regulator IC and its BLOCK DIAGRAM
1 Power failure JFLB Assy (VFDP2R7_F1, VFDP2R7_F2, V+27, 10.13 VOLTAGES
V+3R3_SW) of the FL. peripheral parts for each power supply. If they are
properly mounted, then the parts may be defective. 24 25 22 19
Check the waveforms and connection of

communication line of FL in the JFLB Assy. If no signal is output, the PANEL CPU (IC1007) may 10.14
• J_SCLK be defective. WAVEFORMS
2 Signal errors JFLB Assy
• J_SO If output signal is no problem, JOG FL (V1801) may 1 4 3 2
• J_LAT be defective.
• J_BK
24 CDJ-850
1 2 3 4
5 6 7 8
A
[2-3] The LED does not light.
If no signal is output, check a mounting state of
Check that the control signal for the LED [10] Basic operation
1 Signal errors DFLB Assy PANEL CPU(IC1007). If the mounting is OK, the
is output from the PANEL CPU (IC1007). check of CPU/DSP
IC1007 may be defective.
Check that the voltage (2.2 V) is present If the voltage is abnormal, the LED, transistor or
2 Defective parts DFLB Assy at both ends of the LED. —
peripheral resistors may be defective.
[3] Operations (Keys/variable controls/JOG)

As operations of all keys, variable controls, and JOG dial can be checked in Service mode. B
[3-1] No key functions

PLAY, CUE, AUTO BEAT LOOP 1-4, BEAT SELECT, REV, LOOP IN/OUT, RELOOP, or USB STOP key does not function.
Check if there is loose connection on the If there is no loose connection and if the signal does 10.15 EACH
1 Loose connection Related point signal line from the PANEL CPU (IC1007) not become "L" when the SW is pressed, that SW is
/Defective SW SIGNAL LEVEL
up to the SW. defective.
Defective PANEL If the symptom persists after the above Check a mounting state of PANEL CPU (IC1007). [10] Basic operation
2 CPU (IC1007)
DFLB Assy check of CPU/DSP
corrections, If the mounting is OK, the IC1007 may be defective.
The signals from other keys are analog and connected to multiple switches.
No. Cause Diagnostics Point Item to be Checked Corrective Action Reference C
Check if there is loose connection on the If the SWs connected to the signal line function
1 Loose connection Related point signal line from the PANEL CPU (IC1007) properly and if the connections are properly made, —
/Defective SW up to the SW. the SWs may be defective.
2 CPU (IC1007) DFLB Assy check of CPU/DSP
corrections, If the mounting is OK, the IC1007 may be defective.
[3-2] Rotary selector not controllable

Check if the signals from the RENC_1, RENC If the signals are not normal, check the connections of
Defective rotary 10.15 EACH
1 DFLB Assy _2, and RENC_SW signal lines are normal the signal lines. If the connections are properly made,
selector SIGNAL LEVEL
when the rotary selector is turned or pressed. the Rotary selector (S1018) may be defective. Replace it.
Defective PANEL If the symptom persists after the above Check a mounting state of PANEL CPU (IC1007). [10] Basic operation D
2 CPU (IC1007) DFLB Assy
corrections, If the mounting is OK, the IC1007 may be defective. check of CPU/DSP
[3-3] Variable controls not controllable

Tempo slider not controllable
DFLB Assy Check if there is loose connection on the
Loose If the connections of signal line are improper,
1 connection SLD1 Assy signal line from the PANEL CPU (IC1007) —
resolder it.
SLD2 Assy to the tempo slider (VR1501).
If the voltage of the ADCT signal (IC1007-pin 1) is not 10.15 EACH
Defective tempo DFLB Assy 1.65 V, or the voltage of the ADIN signal (IC1007-pin 2)
2 Check the ADCT and ADIN signals level. SIGNAL LEVEL
slider SLD2 Assy does not change between 3.3 V and 0 V, the Tempo
C D
slider (VR1501) may be defective.
E
3 DFLB Assy
CPU (IC1007) corrections, If the mounting is OK, the IC1007 may be defective. check of CPU/DSP
VINYL SPEED ADJUST not controllable

DFLB Assy Check if there is loose connection on the
Loose If the connections of signal line are improper,
1 signal line from the PANEL CPU (IC1007) to —
connection SLD1 Assy resolder it.
the VINYL SPEED ADJUST VR (VR1301).
Defective If the voltage of the TCH/REL signal line (IC1007-pin 88) 10.15 EACH
DFLB Assy SIGNAL LEVEL
2 variable Check the TCH/REL signal level. does not change between 3.3 V and 0 V, the VINYL
SLD1 Assy E
controls SPEED ADJUST VR (VR1301) may be defective.
3 Defective PANEL DFLB Assy

If the symptom persists after the above Check a mounting state of PANEL CPU (IC1007). [10] Basic operation F
CDJ-850 25
5 6 7 8
1 2 3 4
A
[3-4] Abnormalities regarding the JOG dial
After the JOG Assy is disassembled then reassembled, be sure to check that the load value for the JOG dial is within the
specified range. (Refer to the "8.4 JOG DIAL ROTATION LOAD ADJUSTMENT".)
Turning of the JOG dial is not detected
DFLB Assy Check the waveforms of signal lines. 10.14
Defective part of If no waveform can be confirmed, the photo WAVEFORMS
1 JFLB Assy JOG1_C (IC1007-pin 26)
photo interrupter interrupter (PC1901) may be defective. 5 6
JOGB Assy JOG2_C (IC1007-pin 25)
2 DFLB Assy
B Pressing on the JOG dial cannot be detected.

If the JOG_SW signal (IC1007-pin 27) is not set to 10.15 EACH
DFLB Assy Check the level of JOG_SW signal (IC1007 "L" when the JOG dial is pressed and it is not set to SIGNAL LEVEL
1 Defective part
JFLB Assy -pin 27) when the JOG dial is pressed. "H" when the JOG dial is not pressed, the SHEET F
SW(DSX1078) may be defective.
Defective PANEL If the symptom persists after the above Check a mounting state of PANEL CPU (IC1007).
2 DFLB Assy —
CPU (IC1007) corrections, If the mounting is OK, the IC1007 may be defective.
Noise is heard when the JOG dial is turned.

Check if the JOG FL of the JFLB Assy has been
Defective shifted upward from the holder. The JOG FL may interfere with JOG A. —
C
attachment of Also check the JOGB Assy is attached normally.
the JOG FL. JFLB Assy
1
Defective gear JOGB Assy If there are any scratches, replace the scratched gear
There may be any scratches on the 3
or JOG DIAL B. with a new one. If there is any foreign object, remove —
gears or some foreign object between
the gears. it then replace the gears with new ones.
Gears to be replaced: Load gear, Gear A, Gear B
The JOG dial turns too freely. (The load value for the JOG dial is outside the specified range.)
If it is outside the specified range, adjust the position
8.4 JOG Dial
of the Adjust Plate to change the load value for the
Rotation Load
JOG dial, referring to “Load adjustment method” in
Check that the load value for the JOG dial Adjustment.
Improper adjust- “8.4 JOG Dial Rotation Load Adjustment.”
is within the specified range, referring to
1 ment or assembly JOG Assy “Measuring method” in “8.4 JOG Dial During the above adjustment, if the upper-limit adjust-
of the JOG dial ment position of the Adjust Plate is reached, oil may 8.4 JOG Dial
D Rotation Load Adjustment.”
have been spattered on the Cam Plate. Rotation Load
Replace the washer, load gear, and cam plate with Adjustment.
new ones, then reassemble.
Resistance to turning the JOG dial is too strong. (The load value for the JOG dial is outside the specified range.)
If it is outside the specified range, adjust the position
of the Adjust Plate to change the load value for the 8.4 JOG Dial
JOG dial, referring to “Load adjustment method” in Rotation Load
Improper adjust- “8.4 JOG Dial Rotation Load Adjustment.” Adjustment.
Check that the load value for the JOG dial
ment of the JOG
1 JOG Assy is within the specified range, referring to During the above adjustment, if the lower-limit adjust-
dial or defective
washer, gear, or “Measuring method” in “8.4 JOG Dial ment position of the Adjust Plate is reached, shavings 8.4 JOG Dial
cam plate Rotation Load Adjustment.” from the worn-out washer may have increased the Rotation Load
friction. Replace the washer, load gear, and cam plate Adjustment.
E with new ones, then reassemble.
26 CDJ-850
1 2 3 4
5 6 7 8
A
[4] USB (USB-Type A), PC (USB-Type B)
[4-1] USB (USB-Type A)
Check the following, with a USB device connected to the USB-Type A connector.
USBA Assy Check the connections of the USBA_D_P/N
1 Loose —
connections CMPX Assy communication line, USB_VBUSON and If connection is improper, resolder it.
MAIN Assy USB_CODETFLG signal lines.
Check the voltage level of V+5_USB If the voltage of IC2002-pin 3 is abnormal, IC2002
USB VBUS is USBA Assy 10.13 VOLTAGES
2 (JA2201-pin 1 and IC2002-pin 3) of USB may be defective.
defective. CMPX Assy 7
power supply. If the voltage of JA2201-pin 1 is abnormal, go to [3].
• If the USB_VBUSON(IC504-pin 4) is not "H", MAIN
CPU(IC103) may be defective. B
• If the USB_VBUSON(IC504-pin 4) and USB_
Check the signal level of USB_CODETFLG 10.15 EACH
CODETFLG(IC2003-pin 5) are "H", IC2003 may be
3 Defective part CMPX Assy (IC2003-pin 5) and USB_VBUSON(IC504- SIGNAL LEVEL
defective.
pin 4). • If the USB_VBUSON(IC504-pin 4) is "H" and USB_
L K
CODETFLG(IC2003-pin 5) is "L", USB power

supply may be short-circuited in the ground or
IC2003 may be defective.
[4-2] PC (USB-Type B) does not work

Check the following, with a USB device connected to the USB-Type B connector.
Loose Check the connections of the USBB_D_P/N If connection is improper, resolder it. 10.15 EACH
1 connections — C
communication line and VBUS_B signal line. SIGNAL LEVEL
— If the symptom persists after the above [10] Basic operation

2 Defective part The MAIN CPU (IC103) may be defective.
corrections, check of CPU/DSP
[5] AUDIO OUT

The analog audio signal is not output.
Loose MAIN Assy Check the connection of the audio signal
1 If connection is improper, resolder it. —
connections CMPX Assy lines (ROUT/LOUT).
Check the AMUTE signal.
MUTE signal MAIN Assy 10.15 EACH D
2 "L" (release mute) at normal playback. If the signal is abnormal, loose connection and mute
error DFLB Assy SIGNAL LEVEL
Check the MAIN_XMUTE signal. circuit may be defective.
CMPX Assy H I
"H" (release mute) at normal playback.
• If the V+10_A voltage level is abnormal, Q2028
and its peripheral parts may be defective.
• If the V-AUDIO(V-10_A) voltage level is abnormal,
Check the voltages for audio (V+10_A, Q2031 and its peripheral parts may be defective.
V-AUDIO(V-10_A), V+5_A, V+3R3_A, • If the V-5_A voltage level is abnormal, IC406 10.13 VOLTAGES
3 Power failure MAIN Assy V+1R25). and its peripheral parts may be defective. 5 6 16 11 12
Check also if the protector (P2003) is • If the V+3R3_A voltage level is abnormal, IC402
broken. and its peripheral parts may be defective.
• If the V+1R25 voltage level is abnormal, IC403
and its peripheral parts may be defective.
Signal error Check the AUDIO DSP (IC301) and AUDIO AUDIO DSP (IC301), AUDIO DAC (IC302) and its [10] Basic operation E
4 MAIN Assy
Defective part DAC (IC302). peripheral parts may be defective. check of CPU/DSP
[6] CONTROL
Improper fader operation after fader start.
Loose MAIN Assy Check the connection of the control signal
1 If connection is improper, resolder it. —
connections CMPX Assy lines (CONT1/CONT2).
If the input signal cannot be recognized at input pin

Signal error Check the waveform of the control signal of MAIN CPU (IC101), the signal line or the
2 MAIN Assy 10.14
peripheral devices may be defective. F
Defective part lines (CONT1/CONT2). WAVEFORMS
If the input signal can be recognized, the MAIN
CPU (IC103) may be defective.
CDJ-850 27
5 6 7 8
1 2 3 4
A
[7] DRIVE ASSY
[7-1] Improper operation of the loading mechanism
Cables Check the connection of the motor-drive signal
Loose MAIN Assy line LO±. Check that the wires between the
1 If soldering is improper, resolder it.
connections JINT Assy loading motor (DC motor) and the SLMB Assy —
If the wires are broken, replace them.
SLMB Assy are securely soldered. Check also the wires
are not broken.
Check the connections and waveforms of the
MAIN Assy LPS1 and LPS2 signal lines. In the normal state, If the signal waveform is not proper, loose connection 10.14
2 Signal errors JINT Assy the LPS1 and LPS2 signals becomes "L" when and the loading detection SWs (S1701 and S1702) WAVEFORMS
SLMB Assy the loading detection SWs(S1701 and S1702) may be improperly soldered or defective. 11 12
are set to ON.
B
Check the power voltages. For any power-supply section that does not output
4.3 POWER SUPPLY
3 Power failure MAIN Assy V+7R6_M, V+5R6_M, VREF1R65, the voltage, check the mounting statuses of the
V+3R3_B, V+3R3, V+1R2A regulator IC and its peripheral parts. BLOCK DIAGRAM
No loading (There is an abnormal noise.)

Slotin Mecha Check if the SW lever has shifted on the
Improper
1 Assy loading detection SWs (S1701 and S1702) If assembling is improper, resolder it. —
assembling
SLMB Assy on the SLMB Assy.
Loose MAIN Assy If the signal waveform is not proper, loose connection 10.14
Check the waveforms on the LPS1 and
2 connections JINT Assy and the loading detection SWs (S1701 and S1702) WAVEFORMS
LPS2 signal lines.
Signal errors SLMB Assy may be improperly soldered or defective. 11 12
C [7-2] The stepper does not work.

Loose MAIN Assy Check the connection of the stepping-motor If connection is improper, resolder it.
1 —
connections JINT Assy drive signal line ST1± and ST2±.
Check the waveform of INSW (INSIDE) If the signal is not proper, check the connections. 10.15 EACH
signal. In the normal state,The INSIDE SW of If connections are properly made, replace the SIGNAL LEVEL
2 Signal errors MAIN Assy
TM Assy-S (Traverse mecha) becomes "L" TM Assy-S (traverse mecha). O
when the INSIDE SW is set to ON.
Check the power voltages. For any power-supply section that does not output
4.3 POWER SUPPLY
3 Power failure MAIN Assy V+7R6_M, V+5R6_M, VREF1R65, the voltage, check the mounting statuses of the
BLOCK DIAGRAM
V+3R3_B, V+3R3, V+1R2A regulator IC and its peripheral parts. Replace it.
D
[7-3] No CD playback
Short switch S2501 is in the off (open) In the normal operation, turn the short switch to
1 Short switch CNCT Assy —
state. off (open).
Check if any foreign matter, such as
Any foreign TM Assy-S shavings, dirt, or dust, is attached to the
2 Clean a lens. —
matter attached (Traverse mecha) lens of the Pickup Assy.
3 Defective pickup MAIN Assy Check the LD current value. Refer to the “5.3 Diagnosis of the Pickup Assy.” 5.3 Diagnosis of
Measure the actuator resistance value. the Pickup Assy
Check operations of the CD drive, referring to the

If the symptom persists after the above
procedures described in “6. SERVICE MODE.” 6. Service mode
4 — Service mode corrections, check operations of the CD
If the CD drive functions improperly,
E drive in Service mode.
see “[8] SERVICE MODE” in this section.
28 CDJ-850
1 2 3 4
5 6 7 8
A
[8] SERVICE MODE
[8-1] The measured error rate is outside the specified range in Player Operation mode.
Scratches or Check if the recording surface of the disc is If it is clearly dirty, replace it with a disc of good
1 dirt on the disc DISC dirty. condition. —
If the error rate measured in a different area is OK,

Measure the error rate, using the same disc the disc is defective. Replace the disc with one in
Scratches or
2 DISC that produced the bad error rate but using good condition. —
dirt on the disc
the addresses in a different area. If no error rate measured in various areas throughout
the entire surface of the CD is OK, go to [3].
TM Assy-S Check if any foreign matter, such as

Any foreign
3 shavings, dirt, or dust, is attached to the Clean the lens. —
matter attached (Traverse mecha) B
lens of the Pickup Assy.
Improper TM Assy-S Check that the TM Assy-S (traverse mecha)
4 If it has not, reinstall it properly. —
assembly (Traverse mecha) has been securely installed.
Improper Check that the loading mechanism Assy
5 Slotin Mecha If it has not, reinstall it properly. —
assembly has been securely installed.
Any foreign TM Assy-S Check for any foreign matter on the spindle
6 Remove any foreign matter. —
matter attached (Traverse mecha) table.
Any foreign Check if any foreign matter is attached to
7 Slotin Mecha Remove any foreign matter. —
matter attached the magnet portion of the clamper.
If their waveforms are not of the same quality, check 10.14
Check that the waveforms of the RFO and the mounting status of the Servo IC (IC201). WAVEFORMS
8 Signal errors MAIN Assy
AGCRF signals form clear eye patterns. If it is correctly mounted, then it may be defective. 13 14
Replace it.
C
TM Assy-S If the symptom persists after the above 5.3 Diagnosis of
9 Defective pickup See “5.3 Diagnosisi of the Pickup Assy” for details.
(Traverse mecha) corrections, the Pickup Assy
[8-2] The drive does not work during Test Operation mode.
The LD does not emit light.
Check the LD current and measure the 5.3 Diagnosis of
1 Defective pickup — See “5.3 Diagnosis of the Pickup Assy” for details.
resistance value of the actuator. the Pickup Assy
The spindle motor does not rotate.
D
If the signal is not normal, check the mounting 10.15 EACH
Check that the DRVMUTE1 and 2 signal statuses of the DRIVER IC (IC204) and MAIN CPU
1 Signal errors MAIN Assy SIGNAL LEVEL
becomes H after loading is completed. (IC103) terminals. If they are properly mounted, then S
the IC103 may be defective.
Check a SPIN signal. If the signal is not normal, check the mounting 10.15 EACH
2 Signal errors MAIN Assy In the normal, 1.65 V at the center. statuses of the DRIVER IC (IC204) and Servo CPU
SIGNAL LEVEL
The voltage in the start-up acceleration is (IC201) terminals. If they are properly mounted, then
T
around 3 V. the IC204 and IC201 may be defective.
Check the mounting statuses of the regulator IC of
the power-supply section that produces that voltage
Check the power voltages. and its peripheral parts. If they are properly mounted, 4.3 POWER SUPPLY
3 Power failure MAIN Assy (V+7R6_M, V+5R6_M, VREF1R65, then the parts may be defective. BLOCK DIAGRAM
V+3R3_S) VREF1R65 is produced at the Servo IC (IC201).
If this voltage is not output, check the mounting
status of the IC201. If it is properly mounted, then the E
part may be defective.
If the symptom persists after the above —

4 Defective parts — DRIVER IC(IC204) may be defective.
corrections,
In-focus not possible

Check the LD current and measure the 5.3 Diagnosis of
1 Defective pickup MAIN Assy Refer to the “5.3 Diagnosis of the Pickup Assy.”
Check the mounting statuses of the regulator IC of
the power-supply section that produces that voltage
Check the power voltages. and its peripheral parts. If they are properly mounted,
(V+7R6_M, V+5R6_M, VREF1R65, then the parts may be defective. 4.3 POWER SUPPLY
2 Power failure MAIN Assy
V+3R3_S) VREF1R65 is produced at the Servo IC (IC201). BLOCK DIAGRAM
If this voltage is not output, check the mounting F
status of the IC201. If it is properly mounted, then the
part may be defective.
CDJ-850 29
5 6 7 8
1 2 3 4
A
No tracking close
1 Defective pickup MAIN Assy Check the LD current and measure the Refer to the “5.3 Diagnosis of the Pickup Assy.” 5.3 Diagnosis of
For any power-supply section that does not output
Check the power voltages.
the voltage, check the mounting statuses of the 4.3 POWER SUPPLY
2 Power failure MAIN Assy (V+7R6_M, V+5R6_M, VREF1R65,
regulator IC and its peripheral parts. If they are BLOCK DIAGRAM
V+3R3_S)
properly mounted, then the parts may be defective.
TM Assy-S Check that focusing is in. (If focusing is out,

3 — See “In-focus not possible” above. —
(Traverse mecha) tracking close is not possible.)
B
[9] Error Codes
How to respond when an error code is displayed on the FL DISPLAY is described below.
[9-1] E-6002: COMMUNICATION ERROR

The MAIN CPU cannot write in a program to the AUDIO DSP at start-up.
1 Power failure MAIN Assy Check the power voltages for Audio DSP. If the voltage level is abnormal, IC402 or IC403 10.13 VOLTAGES
(V+3R3_A, V+1R25) may be defective. 11 12
If the AUDIO DSP (IC301) is not operating, AUDIO

Check if the AUDIO DSP (IC301) is DSP (IC301) and its peripheral parts may be defective. [10] Basic operation
2 Defective part MAIN Assy
operating. If the AUDIO DSP (IC301) is operating, the MAIN check of CPU/DSP
CPU (IC103) and its peripheral parts may be defective.
C
[9-2] E-7201: TOC READ ERROR

TOC data cannot be read from a disc.
Measure the error rate in Player Operation
mode of Service mode in order to distinguish
— TM Assy-S whether the cause is attributable to the disc See [8] SERVICE MODE for details. [8] SERVICE
1
(Traverse mecha) or to the player. For measurement, play back MODE
the reading point at which reading resulted in
an error, by listening to the sound.
[9-3] E-8709: COMMUNICATION ERROR

D
Communication between the PANEL CPU (IC1007) and MAIN CPU (IC103) is not possible.
[1-3] “E-8709” is
Check the waveforms of TSCK, TSI, displayed on the
— DFLB Assy See “[1-3] “E-8709” is displayed on the DATA FL
1 PNL_BUSY, TSO, and MAIN_BUSY, DATA FL display
MAIN Assy display after startup“ for details.
check the voltages of V+3R3 and V+1R2. after startup
30 CDJ-850
1 2 3 4
5 6 7 8
A
[10] Confirmation of basic operations of the CPU/DSP
First, check if the voltage at each section is OK.
[10-1] Periphery of the MAIN CPU: IC103

Check the waveforms and levels of the following If both the Reset and Oscillation circuits are OK, but the
signals: SH_STATUS signal is fixed at "L" or "H" (not "H/L" pulse
• MAIN_XRST: MAIN CPU releases reset with "H". signal), the Main CPU is not operating. 10.14
• 33 MHz OSC circuit: Oscillation circuit for If the reset is not "H", following points may be defective. WAVEFORMS
MAIN Assy 4 1
1 — MAIN_CPU system clock. • Loose connection of the reset line
(IC103) • 48 MHz OSC circuit: Oscillation circuit for USB • Defective part of PANEL CPU(IC1007)
10.15 EACH
clock. • Malfunction detection of the voltage.
SIGNAL LEVEL
• SH_STATUS: Status signal of MAIN CPU.
P B
"H/L" pulse signal in the normal state. If both the Reset, Oscillation circuits and 66 MHz clock
• CLK66M: 66 MHz clock signal output for FLASH signals are OK, IC103 (MAIN CPU), IC101 (FLASH ROM)
ROM and SDRAM. or IC102 (SDRAM) may be defective.
[10-2] SERVO DSP: IC201

10.14
Check the waveforms and levels of the WAVEFORMS
MAIN Assy following signals (in CD PLAY mode): If both the Reset and System clock signals are OK, 3 6
1 — SERVO DSP • SRVRST: SERVO DSP releases reset with "H". but the SRVSCLK signal is not output, the SERVO
(IC201) • CLK_S_16M: 16 MHz system clock signal input. DSP (IC201) may be defective. 10.15 EACH
• SRVSCLK: Communication clock signal. SIGNAL LEVEL
R
C
[10-3] AUDIO DSP: IC301
10.14
Check the waveforms and levels of the WAVEFORMS
MAIN Assy following signals (in PLAY mode): If both the Reset and System clock signals are OK, 5 2
1 — AUDIO DSP • DSPDREQ: Communication request signal but the DSPDREQ signal is not output, the AUDIO
10.15 EACH
(IC301) • DSPRST: AUDIO DSP releases reset with "H". DSP (IC301) may be defective.
SIGNAL LEVEL
• CLK_A_16M: 16 MHz system clock signal input.
Q
[10-4] PANEL CPU: IC1007

D
Check the waveforms and levels of the following
signals: 10.14
• RESET(IC1007-pin 12): PANEL CPU releases WAVEFORMS
DFLB Assy 8
1 — reset with "H". If both the Reset and Oscillation circuits are OK, but
PANEL CPU
• 16 MHz OSC circuit: Oscillation circuit for the TSCK signal is not output, the PANEL CPU 10.15 EACH
(IC1007)
system clock. (IC1007) may be defective. SIGNAL LEVEL
• TSCK(IC1007-pin 37): Communication clock G
signal output.
CDJ-850 31
5 6 7 8
F
E
B
A
D
C
32
Item Specifications Measurement Procedures Failure Judgment Remarks
LD (Laser Diode) current Typ. 65 mA 1 Make sure that no CD is loaded. The LD can be judged to have degraded if the LD
Max. 75 mA 2 Enter the CD drive diagnosis mode. current [A], which is calculated by dividing the
3 Connect a tester between the test lands LD3S and LDCHK on the measured voltage difference [V] by 5.5 [Ω], is 75 mA
1
1
MAIN Assy to check the voltage difference between them. or higher.

4 Load a disc.
5 Press the TEMPO button to turn the LD on in the Test operation Note: Check the mounting status of R227, R228,
mode. R232 and R233 (22 ohms).
6 Measure the voltage difference (DC value) between the test lands
LD3S and LDCHK on the MAIN Assy.
7 Press the TEMPO button to turn the LD off.
Confirm that the voltage difference between test lands LD3S and
LDCHK becomes 0 then disconnect the tester.
Focus coil resistance 3.7 ± 0.55 Ω 1 Make sure that no CD is loaded. If the measurement result is beyond the specified
2 Set the LD short-circuit switch (S2501) to Short side. value, the pickup is in failure.
(see right figure.) CNCT Assy
3 Disconnect the FFC cable that connects the CNCT Assy and the
JINT Assy from the CN2302 connector.
4 Measure the conductor resistance of the terminal assembly
2
2
SHORT SW
between Pins 23 and 24 of the FFC cable. SHORT OPEN
S2501
Tracking coil resistance 4.3 ± 0.65 Ω 1 Make sure that no CD is loaded. If the measurement result is beyond the specified 2
2 Set the LD short-circuit switch (S2501) to Short side. value, the pickup is in failure.
(see right figure.)
3 Disconnect the FFC cable that connects the CNCT Assy and the
LD short-circuit
JINT Assy from the CN2302 connector.
switch
4 Measure the conductor resistance of the terminal assembly
SHORT OPEN
between Pins 21 and 22 of the FFC cable.
5.3 DIAGNOSIS OF THE PICKUP ASSY
CDJ-850
S-shaped level Reference: 1 Enter the CD drive diagnosis mode If the measurement result is twice or more, or 50 % Usually use a pressed CD, as the
1.7 Vp-p 2 Load a pressed CD. (Standby) or less of the reference value, the pickup or the measurement result depends on the
3 Connect and set a digital oscilloscope so that the p-p level at the MAIN Assy is defective. disc type.
test land (FE) can be measured.
4 During Test Operation mode, press the MASTER TEMPO, then
3
MENU buttons to send a command.
3
5 Measure the p-p level (S-shaped level) at the FF.
TE (Tracking Error) level Reference: 1 Enter the CD drive diagnosis mode If the measurement result is twice or more, or 50 % Usually use a pressed CD, as the
1.0 Vp-p 2 Load a pressed CD. (Standby) or less of the reference value, the pickup or the measurement result depends on the
3 Connect and set a digital oscilloscope so that the p-p level at the MAIN Assy is defective. disc type.
test land (TE) can be measured.
4 During Test Operation mode, press the buttons in the following
order to send a command: MASTER TEMPO, TEMPO, RELOOP,
then LOOP IN twice.
5 Measure the p-p level of waveform at the TE.
RFO level Reference: 1 Play back a pressed CD. If the measurement result is twice or more, or 50 % Usually use a pressed CD, as the
1.1 Vp-p 2 Measure the p-p level of RF waveform at the RFO test land on the or less of the reference value, the pickup or the measurement result depends on the
MAIN Assy. MAIN Assy is defective. disc type.
4
4
AGC (Auto Gain Control) 1.2 Vp-p ± 10 % 1 Play back a CD. If the RFO level value is twice or less, or 50 % or You may disconnect the measuring
RF level 2 During playback, measure the p-p level of RF waveform at the less of the reference value, and the AGC RF level is equipment during measurement, if you
AGCRF test land on the MAIN Assy. out of the range stipulated in the specifications, the wish.
MAIN Assy is defective. The measurement result does not
depend on the disc type.
5 6 7 8
5.4 CONNECTION CHECK WITH THE PC
[1. USB B connector] A
Whether communication between the PC connected via the USB B connector and this unit is properly performed or not can
be confirmed on the PC.
Note: Installation of the driver software is not necessary.
Connect to PC
When you check the connection, connect this unit to the PC and confirm that "CONNECTED" is displayed on the display.
How to Enter
Press the [ ] button.
B
When you press the PC button during DISC or USB use, caution is displayed.
Press the PC button according to caution again, or press the Rotary selector.
Use Device Manager for checking.

If the PC and this unit are properly connected, the components of this unit are added in Device Manager (under Hardware)
as devices.
If all components are properly displayed, the PC and this unit are properly communicating via the USB connector.
In a case of Windows XP:

Start, Control Panel, System, Hardware, then Device Manager
C
Devices to be added:
Universal Serial Bus controllers
USB Composite Device
Under “Sound, video and game controllers”
USB Audio Device
Human Interface Devices
HID-compliant device
USB Human Interface Device
A communication check may be easily performed if connection is

made with Device Manager displayed on the PC screen.
D
CDJ-850 33
5 6 7 8
1 2 3 4
5.5 ABOUT POWER SUPPLY MONITORING

The Panel CPU of this unit always monitors for power failure of the unit while power is on and will shut the unit off
A immediately after an error is detected and notify of the error by LED indications.
• Content to be monitored
Any power failure generated inside an Assy or Power Supply Assy, such as voltage drop and voltage rise
Power to be monitored: V+7R6_M, V+12, V+5R6, V+1R2, V+1R25, V+3R3_S, V-10_A, V+3R3_SW, V+6R6_FL, V+38
• Microcomputer Detection terminal and its terminal voltage

44-pin VDET terminal of IC1007 (PANEL CPU)
Normal: 3.3 V
During power failure: 0 V
• Timing of monitoring start

B 0.1 sec after the unit is turned ON
• Timing upon judgment as a failure

0.5 sec after an error is detected
• LED indication when an error is generated

If an error is generated, the STANDBY LED will flash after the unit shuts itself off.
• Restoration method
After the unit shuts itself off because of an error, after completing diagnosis, unplug the AC power cord and wait about
1 minute before turning the unit back on.
Error-detection status is retained for about 1 minute after the AC power cord is unplugged, during which time signals
C from the POWER switch are not accepted and the unit cannot be turned on.
Diagnostic procedure
1 Unplug the AC power cord.
2 Remove R1123 from the DFLB Assy.
Note: This step will disable power supply monitoring.
3 Plug in the AC power cord.
4 As the unit is turned on in a normal way, check each voltage in this state.
Note: Because power will be forcibly supplied even if any voltage is abnormal, if abnormal voltage continues, the
defective point may produce heat, which may be dangerous. Therefore, during diagnosis, be sure to unplug the
AC power cord several seconds after it is plugged in so that forcible powering will not continue.
D 5 If the voltage of any power IC is abnormal, the circuit that uses that power or the power IC itself may be defective.
6 Repair the detective part.
7 Return R1123 to its original position on the DFLB Assy.
Note: This step will enable power supply monitoring.
5.6 ABOUT THE PROTECTORS

E
This unit is provided with protectors (elements for protection against excess current) on the power lines to protect the unit’s
parts and circuits from excess current and excess voltage. If any abnormal power short-circuiting is generated, a protector
will be activated to protect parts and circuits.
• Locations and functions of protectors

P2003 DEK1095-: Protection against excess current on the V+12_A and V+10_A lines
P2004 DEK1095-: Protection against excess current for V+12_EUP and against excess voltage for its subsequent circuits
Diagnostic procedure
1 Unplug the AC power cord.
F 2 Check for any error, such as short-circuiting or defective parts, in the circuits subsequent to the protector.
3 Repair the detective part.
4 Replace the protector.
34 CDJ-850
1 2 3 4
5 6 7 8
6. SERVICE MODE
6.1 SERVICE MODE
A
The following service modes are prepared for this unit.
1 Confirmation of the button input and an indication function.

It is the mode which checks each input and display function of a button, a JOG dial, the slider volume, and a encoder.
2 Check mode of the load of JOG dial.

It is the mode which measures the load when rotating JOG dial.
3 Indication of various information

It is a mode displaying information such as a version and an error history, a device normal / abnormality judgment.
4 Error display list B

An error code and the contents are shown.
5 Confirmation of movement of the drive unit

It is the mode which checks operation of a mechanism and servo of drive unit.
6 Updating firmware
Mode for firmware updating. Two modes (one for updating using a USB memory device and one for updating using
a CD-ROM) are provided.
Refer to the “8.3 UPDATING OF THE FIRMWARE.”
6.2 ABOUT THE DEVICE OF CDJ-850

Device Name Function Part No. Ref No. Assy
MAIN CPU System control R5S72630P200FP IC103 MAIN Assy
FLASH Memory for MAIN CPU (Firmware) DYW1796 IC101 MAIN Assy
SDRAM Memory for MAIN CPU (Work) K4S561632J-UC75 IC102 MAIN Assy
AUDIO DSP Audio DSP DSPC56371AF180 IC301 MAIN Assy E
SERVO DSP Servo DSP TC94A15FG IC201 MAIN Assy

SERVO DRIVER Disc drive control BD7956FS IC204 MAIN Assy
PANEL CPU Button input, LED & FL control PEG799A8 IC1007 DFLB Assy
CDJ-850 35
5 6 7 8
1 2 3 4
6.3 DETAILS ON SERVICE MODE
A
[1] Confirmation of the button input and an indication function
When it spends a power supply while pushing a TEMPO button and a BACK button simultaneously, It is displayed in the
BROWSE_FL, "SERVICE MODE", and enters into this mode.
When it enters this mode, the TAG-TRACK button is pushed, and the screen is sent as follows, the following status displays
are done.
In this mode, the input of each button, JOG, volume, etc. is normal, and it can check that a display can also be performed
normally. In addition, indication turns on while I push a button.
Caution: In this status display, if a VINYL SPEED ADJUST VOLUME is turned to the limit of the right, it will shift to "the load
measurement mode of JOG." (Refer to the following clause. )
B
At the JOG rotation

BUTTON : The pushed button name is displayed.
JOG (*) : The point moves according to the direction that JOG turned.
ENCODER (*) : The point moves according to the direction that ENCODER
switch turned.
JOG VOLUME (*) : If a VINYL SPEED ADJUST VOLUME is turned to the right,
a bar display will increase.
TEMPO SLIDER VOLUME : If a TEMPO slider knob is moved to the - side, a bar
At the encoder rotation
display will increase.
*: JOG, ENCODER, VOLUME

Display the data for the touched controls in the third line.
C
At the TOUCH/RELEASE VOLUME rotation
36 CDJ-850
1 2 3 4
5 6 7 8
A
Button, Switch Light up LED Status display of BROWSE_FL(BUTTON) Other Displays
PLAY/PAUSE PLAY/PAUSE PLAY
CUE CUE CUE
IN/CUE/IN ADJUST IN/CUE/IN ADJUST IN
OUT/OUT ADJUST OUT/OUT ADJUST OUT
RELOOP/EXIT RELOOP/EXIT RELOOP
TRACK REV (o) TRACK o
TRACK FWD (p) TRACK p 1 (Refer to the display pattern of JOG FL)
SEARCH REV (m) REV m 2 (Refer to the display pattern of JOG FL)
SEARCH FWD (n) FWD n 5 (Refer to the display pattern of JOG FL) B
JOG MODE VINYL JOG MODE 4 (Refer to the display pattern of JOG FL)
TEMPO STANDBY RANGE
MASTER TEMPO MASTER TEMPO MT
TIME MODE/AUTO CUE TIME
DELETE All LED lights up DELETE All JOG-FL lights up
MEMORY MEMORY
EJECT EJECT EJECT
CUE/LOOP CALL c c CALL
CUE/LOOP CALL d CALL d
C
JOG TOUCH JOG TOUCH TOUCH SW 3 (Refer to the display pattern of JOG FL)
AUTO BEAT LOOP 1 AUTO BEAT LOOP 1 A LOOP 1
BEAT SELECT B SELECT
TEMPO SLIDER Increase and decrease ( g MARK of PLAYING ADDRESS)
JOG (FWD) JOG g MARK Right movement (8 points by one rotation)
JOG (REV) JOG g MARK Left movement (8 points by one rotation)
VINYL SPEED ADJUST VOLUME JOG VOLUME g MARK Increase and decrease (8 points) *It becomes "Measurement of the JOG dial D
load" mode if it turns to the right completely.
DIRECTION (Reverse) REV REV

USB_STOP_SW (ON) USB Access USB STOP
PC PC LINK
USB USB USB
DISC DISC DISC
BROWSE BROWSE BROWSE
TAG LIST TAG LIST TAG LIST
INFO INFO INFO
E
MENU MENU MENU
BACK Display pattern changes(Refer to the
TAG TRACK display pattern of BROWSE_FL)
ROTARY SELECTOR (SW) ENC PUSH

ROTARY SELECTOR (FWD ROTATE) ENCODER g MARK Right movement (Max 8 points)
ROTARY SELECTOR (REV ROTATE) ENCODER g MARK Left movement (Max 8 points)
CDJ-850 37
5 6 7 8
1 2 3 4
A
Display pattern of JOG FL
4
B
3
1
5
2
The display pattern of BROWSE_FL

When I push the TAG-TRACK button from above status indication more and send a screen, I display three kinds of patterns
to BROWSE_FL as follows.
If the BACK button is pushed, a display will return a previous page.
(In DATA_FL, it becomes all putting out lights except the case of all-points light.)
Lattice pattern
All turning off
All turning on
E
[2] Check mode of the load of JOG dial

Refer to the "8.4 JOG DIAL ROTATION LOAD ADJUSTMENT."
F
38 CDJ-850
1 2 3 4
5 6 7 8
A
[3] Display of various information
How to Enter Service Modes
1) Version/error history
The Version Display mode is entered after the RELOOP key is held pressed for at least 10 sec.
To change screens between Version Display and Error History, press the VINYL MODE key while the Version Display
screen is displayed.
The error log screens will be changed if you press the CALL (LEFT) or CALL (RIGHT) key while the error history is
displayed.
2) Panel diagnosis/JOG load measurement (Panel microcomputer function)

To enter this mode, set the POWER switch to ON while holding the BACK and TEMPO keys pressed. B
To enter JOG Load Measurement mode, set the TOUCH/RELEASE volume to the + (MAX) position during Service mode.
3) CD drive diagnosis mode

To enter CD Drive Diagnosis mode, set the POWER switch to ON while pressing the TIME and CD SELECT keys pressed.
Set the POWER switch to OFF to quit this mode.
4) Firmware Updating (USB media/program area)

To enter this mode, set the POWER switch to ON while pressing the USB SELECT and RELOOP keys pressed.
After updating is completed, set the POWER switch to OFF to quit this mode.
5) Firmware Updating (CDROM media/program area)

To enter this mode, set the POWER switch to ON while pressing the CD SELECT and RELOOP keys pressed. C
After updating is completed, set the POWER switch to OFF to quit this mode.
6) Factory reset
To enter this mode, set the POWER switch to ON while holding the BACK and USB SELECT keys pressed.
For details on items to be factory-reset, see “8.2 USER SETTABLE ITEMS.”
[4] The list of error display D
Time display shows "E-XXXX".

Main Sub Error Type Medium Error Content
E-6002 — DSP PROGRAM — The program cannot be written in the DSP.
E-7024 — Updating error — Updating failed.

E-7201 26 TOC READ ERROR CD TOC data cannot be read.
22 CD Focus servo cannot be closed.
E-8301 PLAYER ERROR
91 CD The pickup cannot be returned to the inner track of the disc.
12 PLAYER ERROR CD The desired address could not be searched for.
E-8302
15 (Playback error) The address could not be read. E
CD
E-8303 99 Buffer write error CD Writing of music data in the buffer failed.
CD Although compressed music data files (MP3/AAC) are supported by this unit, a data or
E-8304 — Decoding error
decoding (decompression) error was generated.
Although the filename extension of the music file (MP3/AAC/WAV/AIFF) is proper, the format
E-8305 — Format error CD
of descriptions in the file is not supported.
— Although the piece of music had once been registered in the library (database) or a playlist, etc.,
E-8306 No music file USB
that piece had been erased from the USB storage device as of time of playback.
E-8307 — USB writing error USB Writing to the USB storage device failed.
E-8709 — COMMUNICATION ERROR — Communication between the panel CPU and the main CPU failed.
E-9101 90 LOADING TIMEOUT CD A mechanical error (timeout) was generated during loading/unloading of a disc.
F
CDJ-850 39
5 6 7 8
1 2 3 4
A
[5] Confirmation of movement of the drive unit
This mode consists of "player operation mode" and "test operation mode."
<Player operation mode>

Basic operation of Servo, such as setup, play, pause, and track search, is carried out.
Moreover, measurement of an error rate can also be performed.
<Test operation mode>

Servo operation is finely controllable gradually.
B
* It becomes player operation mode and shifts to test operation mode by the key input in the beginning.
* The command treated here is for mainly testing a mechanism and a servo system, and is not for DJ functions, such as scan
and tempo.
Function Main unit button

<Player operation mode>
Servo All Off (Stop) TIME
Play(Trace) / Pause PLAY/PAUSE
Track Search Fwd/Rev TRACK SEARCH FWD/REV
Error Rate Count CUE
Eiect EJECT
Mode Change (-> Test operation mode) MASTER TEMPO
C <Test operation mode>

Servo All Off (Stop) TIME
LD On/Off TEMPO TEMPO
Focus On/Off RELOOP RELOOP
Spindle Kick, Tracking On IN/CUE (HOT LOOP)
Tracking Off OUT (OUT ADJUST)
Slide FWD SEARCH FWD
Slide REV SEARCH REV
Pickup Up/Down UTILITY
Mode Change (->Player operation mode) MASTER TEMPO
Player operation mode command

D
Play(Trace) / Pause
If it is in a stop state, it will set up and play. Moreover, if it is in a play state, whenever it will push a button, a pause and
a play are carried out by turns.
Display a playing address in FL at present.
Note: In this mode, even if it inserts a disc, an automatic setup is not carried out.
Moreover, a play is not carrying out audio reproduction, but is tracing the signal side of a disc.
Trace a disc by a turn of four times speed in the play. The sound is not output.
Track Search F/R

Search a track displayed by a FWD / REV direction and do pause.
E Error Rate Count

I measure an error rate from a present position doing a play/pause for about 10 seconds and display a measurement result
in FL. Usually, a track to measure is made to search and this button is inputted from a pause state.
For example, it is displayed as "3.56E-4 O.K." etc.
If an error rate is less than 3.00E-3, it will be displayed as OK. If an error rate is larger than 3.00E-3, it will be displayed as
NG.
Measurement with the managed disc at the time of factory shipments is a premise.
The product does not judge whether they are inferior goods at the time of service.
Eject
A disc is ejected.
F Mode Change
If the MASTER TEMPO button is pushed into player operation mode, MASTER TEMPO LED will light up, and it will shift to
the below-mentioned "test operation mode."
40 CDJ-850
1 2 3 4
5 6 7 8
A
Test operation mode command
Servo operation is finely controllable gradually.
Keep in mind a test operation mode command that it may give a damage to a player as mistaking the usage.
Servo All Off

When servo is ON, all servo will be turned off if the TIME button is pushed.
“ALL OFF” will be displayed.
LD On/Off
The LD can be turned on or off by pressing the TEMPO key. “LD ON” or “LD OFF” will be displayed.
Focus On B
If the RELOOP key is pressed in Stop mode, the LD is turned ON and auto focusing will be performed.
“FCS ON” will be displayed.
Spindle Kick, Tracking On/Off

If the IN/REALTIME CUE (LOOP IN) key is pressed while the tracking servo is OFF, spindle kick then automatic
adjustment will be performed, after which the tracking servo will be turned ON.
If the key is pressed while the tracking servo is ON, it will be turned OFF. “TRK ON” or “TRK OFF” will be displayed.
Tracking Off
If the OUT (LOOP OUT) key is pressed while the tracking servo is ON, it will be turned OFF.
“TRK ON” will be displayed.
C
Slide FWD
If the SEARCH (FWD) key is pressed while the tracking servo is ON, it will be turned OFF and the slider will be
shifted by about 2 mm in the FWD direction. “SLD FWD” will be displayed.
Slide REV
If the SEARCH (REV) key is pressed while the tracking servo is ON, it will be turned OFF and the slider will be
shifted by about 2 mm in the REV direction. “SLD REV” will be displayed.
Pickup Up/Down
f the DISPLAY/UTILITY key is pressed during Stop mode, the LD will be turned ON then the pickup will be moved
up and down. Focusing will not be closed. “PU UP/DN” will be displayed.
D
Mode Change
If the MASTER TEMPO key is pressed in Test Operation mode, the MASTER TEMPO LED will go dark then above-
mentioned Player Operation mode will be entered.
*To start up the unit in Test mode in steps, input the commands in the following order: "Servo All Off," "Focus On,"
then “Spindle Kick, Tracking On."
E
[6] Updating of the firmware
Refer to the "8.3 UPDATING OF THE FIRMWARE."
CDJ-850 41
5 6 7 8
1 2 3 4
7. DISASSEMBLY
A Note:
(1) Do NOT look directly into the pickup lens. The laser beam may cause eye injury.
(2) Even if the unit shown in the photos and illustrations in this manual may differ from your product, the
procedures described here are common.
Diagnosis
(1) Remove the five screws. (BPZ30P080FNI)
(2) Remove the two screws. (BBZ30P060FTB) 1 1
B 2
1 2
C
1 • Bottom view 1 • Rear view
Front
(3) Remove the control panel section. Control panel section

3
D Diagnosis
MAIN Assy
4
(4) Disconnect the 21P FFC from control panel CN2003

section.
21P FFC
Screw tightening order

The other screws are random order.
MAIN Assy
F
1 2
42 CDJ-850
1 2 3 4
5 6 7 8
SLOTIN MECHA Section A
(1) Change the position of the SHORT SW

(S2501) on the CNCT Assy to "SHORT".
Note:
After work, connect the flexible cable on step (2),
then change the position to "OPEN".
B
CNCT Assy
1 SHORT SW
SHORT OPEN
S2501
(2) Disconnect the four flexible cables. JINT Assy

(3) Remove the earth lead wire by removing D
the one screw. (BPZ30P080FNI)
CN2303
2 CN2304
2 CN2302
2
E
3
2
CN2301
Eart lead wire

F
CDJ-850 43
5 6 7 8
1 2 3 4
A
(4) Remove the four DM screws. (DBA1260)
(5) Remove the four float springs G5. 5 6
(6) Hook the four float springs G5 to the four 5 6
hooks of the float base 05 Assy.
4 4
4 4
5 6 5 6
Float base 05 Assy Float base 05 Assy

5
6
C
Float spring G5 Float spring G5
(7) Remove the SLOTIN MECHA section.

SLOTIN MECHA section
E 7
Direction of the dampers when attaching them
When attaching the dampers, place them so that
their projections (large) face front.
Projection (large)
to the front Damper

F
44 CDJ-850
1 2 3 4
5 6 7 8
TM Assy-S (VTM091) A
[1] Mecha Plate

(1) Remove the four screws. (BPZ30P080FNI)
(2) Remove the mecha plate.
1 ×3
Mecha plate B
C
Note of earth spring Earth spring
• Be sure not to lose it. Mecha plate
• Be careful to the installation places.
• Confirm it by viewing.
This boss is not installation position.
[2] SLOTIN MECHA Assy

(1) Disconnect the one flexible cable. SLOTIN MECHA SLMB
(2) Unhook the four hooks. Assy Assy 1
2
CN1701 2
E
2
CDJ-850 45
5 6 7 8
1 2 3 4
A (3) Remove the SLOTIN MECHA Assy.
SLMB Assy
• Note on Reassembly
When binding the cables from the SLMB Assy, be
careful that the bound part will not protrude from
the edge of the board toward the rear. Bind them
so that the bound part will come to the upper side
of Side A.
SLMB Assy Binder SLOTIN MECHA Assy
3
B
• Bottom view
Bound part
Side A
OK
Rear side Cable Side B
Side A
NG
Side B
Side A
C NG
Side B
[3] TM Assy-S (VTM091)

(1) Short-circuit two positions of figure solodering. Pickup
(short)
D
Note:
After working, connect the flexible cable, 1
then remove the soldered joint (open).
• Rear view
(2) Unhook the four hooks.
E
2 2
2
2
TM Assy-S
(VTM091)
46 CDJ-850
1 2 3 4
5 6 7 8
(3) Release the flexible cables, as required. A
(4) Remove the TM Assy-S (VTM091).
TM Assy-S (VTM091)
Note on the float rubber installation
OK NG
Pole of the float base 05 Assy 4
Hook
B
×2
D
Cleaning the pickup lens
Before shipment, be sure to clean the pickup lens,

using the following cleaning materials:
Cleaning liquid : GEM1004

Cleaning paper: GED-008
F
Pickup lens
CDJ-850 47
5 6 7 8
1 2 3 4
A
Arrangement of the FFC
• Pickup FFC • Spindle motor FFC
Spindle motor Tape
FFC
• Stepping motor FFC
Stepping motor Stepping motor

FFC
Pickup
CNCT Assy FFC
• 5P FFC
F SLMB Assy
5P FFC
48 CDJ-850
1 2 3 4
5 6 7 8
JOG Dial Section A
(1) Disconnect the one flexible cable.

(2) Remove the six screws. (BPZ30P080FNI) JOG dial section DFLB Assy
(3) Remove it while pulling JOG dial section to
front side.
2
1
2 CN1002
2
B
2
2
2
C
Front • Bottom view
Adjust plate
About details of Adjustment etc., refer to the
“8.4 JOG DIAL ROTATION LOAD ADJUSTMENT”. Adjust plate
PCB Assemblies Position
High (SLD1 Assy) PSWB Assy High (DFLB Assy)
Low (KSW1 Assy)

Low (DFLB Assy)
DFLB Assy
KSW1 Assy
SLD1 Assy
Jumper wire Jumper wire
CDJ-850 49
5 6 7 8
1 2 3 4
A
(4) Unhook the three hooks.
(5) Remove the JOG section. JOG section
B 5
C 4
D
(6) Remove the three screws. (DBA1265)
(7) Remove the SW ring.
SW ring
6 ×3
Note:
Be careful not to lost SW spring.
E 7
SW spring
50 CDJ-850
1 2 3 4
5 6 7 8
Notes on replacing the Sheet SW A
Styling of the Sheet SW

Bend it to the direction Sheet SW
of the arrow.
Pasting position of the Sheet SW

Notes:
1. Be careful not to warp the sheet SW. Sheet SW
2. Remove any dirt on the JOG holder M to which
the sheet SW is to be adhered. If some
adhesive for the old sheet SW remains on the
JOG holder M, completely remove it with a cloth
moistened with alcohol.
3. Do NOT place the sheet SW so that it is JOG holder M
mounted on the rib of JOG holder.
C
4. When adhering the sheet SW, be careful not to
Sheet SW
trap air bubbles in it. If air bubbles are formed,
remove the sheet SW and adhere a new
sheet SW. Do NOT reuse the removed sheet SW.
5. When making a connection, be sure to first
release the lock of the connector then securely
relock the connector after making the connection.
Rib
Rib
JOG holder M
Pasting position of the SW cushion HH48/2

SW cushion HH48/2 (×9)
Sheet SW E
CDJ-850 51
5 6 7 8
1 2 3 4
8. EACH SETTING AND ADJUSTMENT

8.1 NECESSARY ITEMS TO BE NOTED
A Before repairing, be sure to check the version of the firmware, and if it is not the latest one, update to the latest version.
Perform the each item when the following parts are replaced.
• MAIN Assy (MAIN CPU) • Confirmation of the version of the firmware (MAIN CPU)
• Updating to the latest version of the firmware
• Part of JOG dial section • JOG dial rotation load adjustment
8.2 USER SETABLE ITEMS

The following data have been set in each IC.
Item for Which User's Setting Value (The factory default Content to be
settings are indicated in bold.) Part No. Part Name Ref No. Assy
Setting is Available Stored
-36 dB/-42 dB/-48 dB/
D A. CUE LEVEL -54 dB/-60 dB/-66 dB/
-72 dB/-78 dB
MIDI CHANNEL 1 to 16
LIBRARY CREATOR LIBRARY/FOLDER
DYW1796 Flash ROM IC101 MAIN UTILITY setting
HISTORY NAME HISTORY
TAGLIST NAME TAG LIST
AUTO STANDBY OFF/ON
VERSION No. —
TIME MODE TIME/REMAIN
AUTO CUE ON/OFF DYW1796 Flash ROM IC101 MAIN Statuses of keys
E
JOG MODE CDJ/VINYL
52 CDJ-850
1 2 3 4
5 6 7 8
8.3 UPDATING OF THE FIRMWARE
A
The device and updater file name for update is the following.
Device File Name

MAIN MAIN CPU C850MAIN.UPD
A version is not contained in a file name.
When USB memory is used

Please use USB memory formatted by FAT32. It does not correspond to HFS+.
1 A file to update is copied to USB memory. B
2 Please turn on the power supply, pushing both the buttons of SOURCE SELECT/USB and RELOOP.
(Please continue pushing until the following caution screen appears.)
3 Starts updating when USB memory is inserted. The FL is displayed the following screen during update.
At the same time, a current version and rewriting version are displayed.
4 Following screen will be displayed if update is completed,

the power is shut off once, then the unit back on.
CDJ-850 53
5 6 7 8
1 2 3 4
A
When CD-R/RW is used
1 A file to update is copied to CD-R/RW.
2 Please turn on a power supply, pushing both the buttons of SOURCE SELECT/DISC and RELOOP.
(Please continue pushing until the following caution screen appears.)
3 The following procedure is the same as that of the case where USB memory is used.
Recovery when failing

When the power supply has been turned off on the way, subsequent normal operation becomes impossible.
When the error code of "E-7024" is displayed, the recovery mode operates when performing the update procedure
mentioned above again, and update is performed.
C In this case, please perform the recovery by USB memory. CD-ROM cannot be used.
54 CDJ-850
1 2 3 4
5 6 7 8
8.4 JOG DIAL ROTATION LOAD ADJUSTMENT
JOG Check Mode : ON

• It is the mode which judges the load (light/-- heavy) numerically when rotating the JOG dial.
TAG TRACK TOUCH /RELEASE

TEMPO /REMOVE
BACK 6 10 16 WIDE
Mode for checking the
load on the Jog dial
POWER ON Maximum position

(fully clockwise direction)
B
JOG Check Mode : CANCEL
POWER OFF
[Measuring method]
1. The adjustment value of adjust plate is adjusted to "0" (Refer to Fig. 2).
2. Enters the mode for checking the load on the Jog dial.
3. The jog dial is mightly rotated. Moreover, the direction of the rotation is clockwise.
4. The rotation speed and time are displayed in FL (Refer to Fig. 1).
The time required so that the rotation may decrease from 3 X speed to 1.5 X speed when maximum speed is only
7 X speed or more is displayed.
The average of the rotation decrease time of 5 times in all is confirmed in spec or less.
Spec: 170 ± 20 msec.
5. When the rotation decreace time is coming off from spec, the adjustment value of adjust plate is changed, and it does
from 2 of above-mentioned to 4. D
Adjust plate
Number of Maximum Measurement
measurement double speed value
To decrease
the load
E
Judgment OK or NG Average value
To increase the load

Fig. 1 Example of displaying FL
Fig. 2 Adjust plate
[Load adjustment method]

Remove the screw fixing the adjust plate, then screw it into the hole corresponding to the value (-1, -2, -3, -4, +1, +2 or
+3) for a load to be added:
-1, -2, -3, -4 : To decrease the load
F
+1, +2, +3 : To increase the load
CDJ-850 55
5 6 7 8
1 2 3 4
9. EXPLODED VIEWS AND PARTS LIST

A
- Screws adjacent to b mark on product are used for disassembly.
- For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
9.1 PACKING SECTION
FLXJ only
B
KXJ5 only
C
AXJ5 only
or or
or or
SYXJ8 only
56 CDJ-850
1 2 3 4
5 6 7 8
(1) PACKING SECTION PARTS LIST

> 1 Power Cord See Contrast table (2) NSP 15 Warranty Card See Contrast table (2)
> 2 Power Cord See Contrast table (2) 16 Caution Card SB See Contrast table (2) A
3 Audio cable XDE3045 17 Vinyl Bag See Contrast table (2)

4 Control cord XDE3063 18 Recycle Label (M) See Contrast table (2)
5 CD-ROM DXX2654 NSP 19 CCC S & E Label See Contrast table (2)
(rekordbox license key attached)
NSP 20 Polyethylene Bag AHG7117
6 Disc force eject pin DEX1008 21 Vinyl Bag Z21-013
(mounted on bottom of product) 22 Pad L DHA1841
7 Operating Instructions See Contrast table (2) 23 Pad R DHA1842
8 Operating Instructions See Contrast table (2) 24 Packing Case See Contrast table (2)
9 Operating Instructions See Contrast table (2)
B
25 Sheet RHX1006
NSP 13 License Key Label DRW2402
NSP 14 License Key Label Assy DXA2190
(2) CONTRAST TABLE

CDJ-850/SYXJ8, CUXJ, FLXJ, KXJ5 and AXJ5 are constructed the same except for the following:
CDJ-850 CDJ-850 CDJ-850 CDJ-850 CDJ-850
Mark No. Symbol and Description
/SYXJ8 /CUXJ /FLXJ /KXJ5 /AXJ5
> 1 Power Cord ADG1154 ADG7022 ADG1154 XDG3054 ADG7079
> 2 Power Cord Not used Not used ADG7097 Not used Not used
7 Operating Instructions (En, Fr, De) DRB1527 Not used Not used Not used Not used
8 Operating Instructions (It, Nl, Es, Ru) DRB1535 Not used Not used Not used Not used
9 Operating Instructions (En, Fr) Not used DRB1526 Not used Not used Not used
D
10 Operating Instructions (En, Es, Zhtw) Not used Not used DRB1528 Not used Not used
11 Operating Instructions (Ko) Not used Not used Not used DRB1530 Not used
12 Operating Instructions (Zhcn, En) Not used Not used Not used Not used DRB1529
NSP 15 Warranty Card ARY7107 Not used Not used Not used Not used
16 Caution Card SB Not used Not used ARM7064 Not used Not used
17 Vinyl Bag Not used Not used Z21-013 Not used Not used
18 Recycle Label (M) Not used Not used Not used DRW2307 Not used
NSP 19 CCC S & E Label Not used Not used Not used Not used DRW2310
24 Packing Case DHG2918 DHG2919 DHG2920 DHG2923 DHG2922
CDJ-850 57
5 6 7 8
1 2 3 4
9.2 EXTERIOR SECION
A
Refer to
"9.3 CONTROL PANEL SECTION".
B
I
H F F
D
J G
H
I
G F
E
C C D
E
C
B
A
D SLMB
CN1701
Stepping
Motor O
C
D
E
B
Pickup
Assy
A
Spindle
Motor
P
E
Refer to
"9.5 SLOTIN MECHA SECTION".
NON-CONTACT
CONTACT SIDE
F
SIDE
58 CDJ-850
1 2 3 4
5 6 7 8
(1) EXTERIOR SECION SECTION PARTS LIST

1 MAIN Assy DWX3174 > 21 Chassis See Contrast table (2)

2 CNCT Assy DWX3151 22 Damper CNV6011 A
3 CMPX Assy DWX3153 23 Float Spring G5 DBH1494
4 USBA Assy DWX3156 24 Mecha Plate DNH2642
5 JINT Assy DWX3157 25 Earth Spring DBH1398
6 ACIN Assy See Contrast table (2) 26 • • • • •

> 7 POWER SUPPLY Assy DWR1463 27 DM Screw (FTC) DBA1260
8 27P FFC DDD1523 28 Screw (M3 x 5) DBA1340
9 17P FFC DDD1524 29 Screw ABZ30P060FTC
10 24P FFC DDD1535 30 Screw BBZ30P060FTB
31 Screw BPZ30P080FNI
B
11 50P FFC DDD1536
NSP 12 Cord With Plug DE010VE0 32 Screw BPZ30P080FTB
13 Connector Assy 6P DKP3869 33 Screw BPZ30P100FTC
14 Connector Assy PF13PP-S07 34 Screw BSZ30P060FTC
15 Card Spacer AEC7133
16 Edge Saddle AEC7582

17 Cushion DEC3177
18 Power Supply Stay DNH2936
19 Main PCB Stay DNH2937
NSP 20 USB Stay DNH2938 C
(2) CONTRAST TABLE

CDJ-850/SYXJ8, CUXJ, FLXJ, KXJ5 and AXJ5 are constructed the same except for the following:
CDJ-850 CDJ-850 CDJ-850 CDJ-850 CDJ-850
Mark No. Symbol and Description
/SYXJ8 /CUXJ /FLXJ /KXJ5 /AXJ5
D
6 ACIN Assy DWX3158 DWX3173 DWX3158 DWX3158 DWX3158
> 21 Chassis DNK5785 DNK5819 DNK5820 DNK5823 DNK5822
CDJ-850 59
5 6 7 8
1 2 3 4
9.3 CONTROL PANEL SECTION
1/2
2/2
1/2
JFLB 2/2
CN1802
Refer to
"9.4 JOG DIAL SECTION".
H
Tape
E
G
I
L
B
CMPX
CN2003
A
x3 M
N
NON-CONTACT
CONTACT SIDE
F A
SIDE
60 CDJ-850
1 2 3 4
5 6 7 8
CONTROL PANEL SECTION PARTS LIST

Mark No. Description Part No.
NSP 1 KSW1 Assy DWS1422
NSP 2 SLD1 Assy DWS1423 A
3 PSWB Assy DWS1424
4 KSW2 Assy DWS1426
5 SLD2 Assy DWS1427
6 DFLB Assy DWX3152 *

7 21P FFC DDD1522
8 USB Cover DNK4999
9 Rotary Knob C DAA1194
10 Dial Knob DAA1259
B
11 Loop Knob DAC2066
12 Play Knob DAC2286
13 Reloop Knob DAC2291
14 Slide Knob DAC2292
15 Power Knob DAC2306
16 Reverse Knob DAC2364

17 Set Button (CALL) DAC2497
18 Vinyl Knob DAC2542
19 Auto Beat Roop Knob DAC2543
20 Del/Memo Knob DAC2545 C
21 Beat Select Button DAC2546

22 Eject Button DAC2548
23 Tempo Button DAC2549
24 USB Stop Button DAC2550
25 Back Button DAC2613
26 Device Select Button DAC2614

27 Mode Select Button DAC2615
28 Search Button Silver DAC2627
29 Slide Sheet 1C DAH2404 D
NSP 30 Silicon Rubber D5 L DEB1456
31 Earth Bracket DNH2941

32 Heatsink DNH2958
33 USB Lens DNK5353
34 EUP Lens DNK5408
35 Encoder Ring DNK5489
> 36 Control Panel DNK5786

37 Display Window DNK5793
38 • • • • • E
39 • • • • •
40 Screw BPZ30P080FNI
∗ The service part of DFLB Assy (DWX3152) is supplied with KSW1 Assy (DWS1422) and SLD1 Assy (DWS1423).
(There assemblies are connected with the jumper wires.)
CDJ-850 61
5 6 7 8
1 2 3 4
9.4 JOG DIAL SECTION
C
Lubricating oil
(ZLB-HFD1600)
Lubricating oil
(ZLB-HFD1600)
Lubricating oil
(ZLB-HFD1600)
D
Lubricating oil
(GYA1001)
E
Lubricating oil
(GYA1001)
DFLB
CN1002
J
B
NON-CONTACT
CONTACT SIDE
F
SIDE
62 CDJ-850
1 2 3 4
5 6 7 8
JOG DIAL SECTION PARTS LIST

1 JFLB Assy DWX3154
2 JOGB Assy DWX3155 A
3 Sheet SW DSX1078
4 13P FFC DDD1521
5 JOG Panel DAH2609
6 JOG Plate DAH2839

7 Load Spring DBH1680
8 SW Spring DBH1681
9 Encoder Spring DBH1710
10 SW Cushion HH48/2 DEC2538
B
11 Encoder Plate DEC2889
12 Ring Cushion L24/2.0 DEC2958
13 Washer DEC3137
14 JOG B DNK4068
15 SW Ring DNK5233
16 Load Gear DNK5236

17 Smoother DNK5237
18 Gear A DNK5241
19 Gear B DNK5242
20 Adjust Plate DNK5300 C
21 JOG Holder M DNK5356

22 JOG Dial A DNK5357
23 Roller A Assy DXB2010
24 JOG Stay Assy DXB2015
25 • • • • •
26 • • • • •
27 Screw (FE) DBA1265
28 Screw BPZ20P100FTC
29 Screw BPZ30P080FNI D
30 Screw IPZ20P060FTC
CDJ-850 63
5 6 7 8
1 2 3 4
9.5 SLOTIN MECHA SECTION
Lubricating oil
(GYA1001)
B
Dyfree
(GEM1036)
JINT
WHT
CN2303
GRY
B
Dyfree
(GEM1036)
GRY
Dyfree
(GEM1036) Dyfree WHT
(GEM1036) Lubricating oil
(GYA1001)
Lubricating oil
(GYA1001)
D
Cleaning liquid (GEM1004)
Cleaning paper (GED-008) CNCT
CN2501
JINT
CN2304
JINT
CN2301
Note:
The TM Assy-S (VTM091) is supplied only in
E assembly form, not as a single parts.
NON-CONTACT
CONTACT SIDE
F
SIDE
Tape
64 CDJ-850
1 2 3 4
5 6 7 8
SLOTIN MECHA SECTION PARTS LIST

1 SLMB Assy DWS1425
2 TM Assy-S (VTM091) DXX2616 A
3 24P FFC DDD1491
4 5P FFC DDD1527
NSP 5 SLOTIN MECHA Assy DXA2206
6 Loading Motor Assy-S DXX2615

NSP 7 DC Motor DXM1384
NSP 8 Worm Gear DNK3910
9 Lead Wire ZWNN1007G28-8-06A
10 Lead Wire ZWNN1007G28-9-06A
B
11 Clamp Spring DBH1374
12 Guide Spring DBH1375
13 SW. Lever Spacer SV DEC2831
14 Loading Lever DNK3406
15 Main Cam DNK3407
16 Disc Guide DNK3478

17 Clamp Arm DNK3576
18 Eject Lever DNK3684
19 Lever AP DNK3835
20 Lever BP DNK3836
C
21 Loading Gear DNK3911

22 Drive Gear DNK3912
23 Loading Base SV DNK4369
24 SW Lever SV1 DNK4370
25 SW Lever SV2 DNK4371
26 Gear Holder SV DNK4372

27 Clamper Assy-S DXX2661
28 • • • • •
29 • • • • • D
30 Screw BPZ20P060FTC
31 Spacer POR (T3) DEB1566

32 Vessel Cushion (C) DEC2854
33 Vessel Cushion T DEC3349
34 Vessel Cushion U DEC3350
35 Front Sheet DED1132
36 Float Base 05 Assy DXB2068

37 Floating Rubber VEB1351
38 Binder ZCA-SKB90BK E
CDJ-850 65
5 6 7 8
1 2 3 4
10. SCHEMATIC DIAGRAM

10.1 CNCT, SLMB and JINT ASSYS
A
A CNCT ASSY (DWX3151)

DKN1445-A DKN1445-A
CN2501 CN2502
(FS)
0.01u/50
FR 1 2 4 FR
C2502 (FS)
FD 2 2 3 FD
(TS)
TR 3 2 2 TR
C2503 (TS)
TD 4
0.01u/50
2 1 TD
NC 5 2 0 GNDS
GNDS 6 GNDS 19 LD780

B LD650 7 1 8 GNDS
09SD PICKUP ASSY
PD 8 GNDS 1 7 GNDS
LD780 9 1 6 GNDS
GNDS 1 0 1 5 GNDS
GNDS
VR780 1 1 1 4 VR780PD
VRCOM 1 2 13 GNDS
GNDS
VR650 1 3 1 2 GNDS
(FS)
GNDS
A 14 11 A
(FS)
B 15 10 B
VRF 1 6 VRF 9 GNDS
SW1_DVD/CD 1 7 8 GNDS
(FS)
C 18 7 C
C (FS)
D 19
(TS)
6 D
E 20
L2502
5 E
Vcc 2 1 VREF 4 VREF
L2501 CTF1410-A
A_S2
VREF 2 2 3 F
CTF1410-A (TS)
F 23 2 V+5P
GNDS 2 4 1 GNDS
V+5P
0.1u/16
C2505
DCH1201-A C2504
C2506
0.1u/16
10u/10
10u/10
C2501
C2507
C2508
NM
NM
VSH1018-A
DCH1201-A
GNDS
S2501
D GNDS LD780
SHORT
3
2
GNDS
1
OPEN
GNDS
SHORT SW
CN1701
S1701
E DSG1017-A VKN1265-A
2 1 LPS2
1 LPS2
2 1 LPS1
2 LPS1
S1702
3 GNDD
DSG1017-A
4 LO+
ZWNN1007G28-9-06A 5 LO-
L=60mm WHITE
LO+ GNDD
LO+
LOADING MOTOR
ASSY-S
LO- LO-
DXX2615
ZWNN1007G28-8-06A
L=60mm GRAY
F
A B B SLMB ASSY (DWS1425)

66 CDJ-850
1 2 3 4
5 6 7 8
C JINT ASSY (DWX3157)

DKN1312-A
CN2301
C2302 NM
INSW 1
SPINDLE MOTOR
W 2
C2303 NM
V 3 DKN1407-A
U
CN2305
4
HB C2304 NM
HB 5 50 INSW
R2302 0
W- 6 49 W
W+ 7 48 W
V- 8 47 V
V+ 9 46 V
U- 10 45 U
U+ 11 44 U
R2303 GNDD B
VCC 1 2 43 GNDD
0 GNDD
VCC
C2307
C2305
42 HW-
NM
0.01u/50
41 HW+
40 HV-
39 HV+
38 HU-
37 HU+
V+5M
DKN1445-A 36 V+5M
CN2302 V+5M
(FS) 35 GNDD
FR 24
(FS) 34 FR
FD 23 33 FD
(TS)
TR 22 32 TR
(TS)
CN201
TD 21 31 TD
GNDS 2 0 30 GNDS
GNDS
LD780 1 9 29 LD780
GNDS 1 8 28 GNDS
GNDS 1 7
GNDS GNDS
27
C
PD
D 2/4
(FS)
GNDS 1 6 26 A_A
(FS)
GNDS 1 5 25 A_B
(FS)
VR780PD 1 4 24 A_C
(FS)
GNDS 1 3 23 A_D
(TS)
GNDS 1 2 22 A_S1
A 11 21 VREF
(TS)
B 10 20 A_S2
V+5P
GNDS 9 19 V+5P
GNDS 8 18 GNDS
C 7 GNDS 17 GNDS
D 6 16 GNDS
E 5 15 LPS1
VREF 4 14 LPS2
F 3 13 GNDS
V+5P 2 (LO) GNDS 12 LO-
GNDS 1
(LO)
11 LO- D
T 10 LO+
9 LO+
8 ST2+
7 ST2+
GNDS 6 ST2-
5 ST2-
4 ST1+
3 ST1+
VKN1374-A 2 ST1-
CN2303
1 ST1-
LPS2 1
LPS1 2
GNDS 3
LO+ 4
0.01u/50
LO- 5
C2301 E
GNDF GNDD
C2306
DKN1288-A
(ST)
CN2304
STEPPING
GNDF
(ST) N M (1608)
ST2- 4
MOTOR
ST2+ 3 (ST) GNDS GNDD GNDF

ST1+ 2
(ST)
ST1- 1
NOTES
NM NO MOUNT (FS)
RS1/10SR***J
(TS)
: Focus Servo Signal Route
CKSRYB***K : Tracking Servo Signal Route
*CAPACITORS (ST) F
GNDD GND for Digital Indicated in Capacity/Voltage(V)
unless otherwise noted. u F , p pF
(LO)
: Stepping Motor Signal Route
GNDS
GND for Servo
*RESISTORS : Loading Motor Signal Route
Indicated in , 5% tolerance
GND for Frame unless otherwise noted. k k , M M .
C
CDJ-850 67
5 6 7 8
1 2 3 4
10.2 MAIN ASSY (1/4)
A
D 1/4 MAIN ASSY (DWX3174) JTAG
• MAIN CPU Block

JTAG_XRST
8 15K
TO OWN SHEET
XASEMD
1 13I
6 TMS
7 TDI
(DA) 5
ASEBRKAK/ASEBRK
: Audio Data Signal Route 3

TRST
TDO
HN1C01
(USB_DN) V+3R3 4
: USB_D_N Signal Route 2 TCK
(USB_DP) 10
: USB_D_P Signal Route 9
(CONT1) V+3R3
: CONTROL1 Signal Route GNDD

GNDD
(CONT2)
: CONTROL2 Signal Route CPU-AU
: Waveform Measuring Point
CONTO
SRVSBSY
DACCS
DSPRST
DSPCS
MUTE
AUDIO_SCK
AUDIO_SO
DATA_R
PLAY
CONTI2
CONTI1
: Signal Level Point
AUDIO_SI
V+1R2
F101
DTL1106-A
1 3
(DA)
DATA
SQ
100u/6.3
330p/50
330p/50
2
SCH
SCH
C177
C109
C122
C195
R196 33
33
R194
R183
R197
NM
FLASH ROM(32M)
33
33
33
R195
B
IC101 V+3R3_B
DYW1796- /J
R118
R121
GNDD C181
R181
R182
R133
VCG1063-A-T
10k
10k
10k
10k
1k
S29GL032N90TFI030 NM
V+3R3_B ADRS17 V+3R3 C182
C128
C135
C140
F102
0.1u
0.1u
0.1u
R122
R123
R180
DTL1106-A NM
330p/50
10k
10k
NM
SCH
C176
1 3
V+1R2A
VCG1063-A
48 1 ADRS16
1000p
SQ
R119
R124
C131
R131
C136
A16 A15
100u/6.3
0.1u
330p/50
10k
10k
10k
2
SCH
C178
C110
C186
C123
C196
0.01u
47 2 ADRS15
BYTE# A14
NM
R101 46 3 ADRS14
33 VSS2 A13
DATA15 45 4 ADRS13
DQ15/A-1
4 5 A12
DATA7 44 5 ADRS12 GNDD
180
179
178
177
176
175
174
173
172
171
170
169
168
167
166
165
164
163
162
161
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
DQ7 A11
3 6 43 6 GNDD
DATA14 ADRS11
DQ14 A10
TDO
ASEBRKAK/ASEBRK
TMS
PVCC13
PVCC12
PVCC11
PF23/SSIDATA1/LCD_VEPWC/AUDATA3
VCC9
VCC10
TRST
TCK
PVSS14
PVSS13
PB1/SDA0/PINT1/IRQ1
PVSS12
VSS9
PF4/FWE/LCD_DATA4/SSCK1
PF10/NAF2/LCD_DATA10/SD_CMD
PF16/FRB/LCD_DON
VSS10
PB0/SCL0/PINT0/IRQ0
PF14/NAF6/LCD_DATA14/SD_WP
2 7
PF2/TCLKC/LCD_DATA2/SSO0
PF6/FOE/LCD_DATA6/SSO1
PF0/TCLKA/LCD_DATA0/SSCK0
PF3/TCLKD/LCD_DATA3/SCS0
PF15/NAF7/LCD_DATA15/SD_CD
PF7/FSC/LCD_DATA7/SCS1
PF8/NAF0/LCD_DATA8/SD_D2
TDI
PF11/NAF3/LCD_DATA11/SD_CLK
181
PF17/FCE/LCD_CL1
DATA6 42 7 ADRS10 SPDLFG
PF5/FCDE/LCD_DATA5/SSI1
PF1/TCLKB/LCD_DATA1/SSI0
DQ6 A9
1 8 41 8 5MON 182
DATA13 ADRS9
DQ13 A8 4:4A
4 5 40 9 FROM BOARD IF BLOCK 183
DATA5 ADRS20 C111
DQ5 A19
DATA12
DATA4
3
2
6
7
39
38
DQ12
DQ4
A20
WE#
10
11
ADRS21
DQMLL ZERO
D 4/4 0.1u
C112
0.1u
184
185
1 8 C101 R114
R102 R106 37 12 10k 186
33 33 V C CR E S E T # R115
0.1u R109
CPU_SRV
DATA11 36 13 10k 187

DQ11 A21
4 5 35 14 22k 188
DATA3 DQ3
3 6 WP#/ACC
DATA10 34 DQ10 15 RX/XBY 189
RY/BY# PB6/SCL3/PINT6/IRQ6
2 7 33 16 190
DATA2 ADRS19
DQ2 A18 PB7/SDA3/PINT7/IRQ7
C DATA9
1 8 32
DQ9 A17
17 ADRS18 C124 191
VCC11
4 5 31 18 0.01u/16 192
DATA1 ADRS8
DQ1 A7 PD15/D31/PINT7/SD_CD/ADTRG/TIOC4D 181: PB2/SCL1/PINT2/IRQ2
3 6 30 19 R185 193
DATA8 ADRS7 PWMSL2IN
DQ8 A6 PD14/D30/PINT6/SD_WP/TIOC4C 182: PB3/SDA1/PINT3/IRQ3
2 7 29 20 56 194
DATA0 ADRS6
DQ0 A5 PD13/D29/PINT5/SD_D1/TEND1/TIOC4B 183: PVCC14
1 8 28 21 195
R107 ADRS5
OE# A4 PD12/D28/PINT4/SD_D0/DACK1/TIOC4A 184: PVCC15
33
27 22 ADRS4 196
VSS1 A3 PVSS16 185: PB4/SCL2/PINT4/IRQ4
26 23 ADRS3 197
CE# A2 R186 PD11/D27/PINT3/SD_CLK/DREQ1/TIOC3D 186: PB5/SDA2/PINT5/IRQ5
C113
GNDD 25 24 ADRS2 PWMSL1IN 1 8 0.1u 198
A0 A1 C114 PVCC16 187: PVSS15
ADRS1 PWMLO 2 7 VCG1063-A 199
PD10/D26/PINT2/SD_CMD/TEND0/TIOC3C 188: VSS11
CS0 DRVMUTE2 3 6 200
PD9/D25/PINT1/SD_D3/DACK0/TIOC3B
DRVMUTE1 4 5 201
PD8/D24/PINT0/SD_D2/DREQ0/TIOC3A
OE 56 202
PD7/D23/IRQ7/SCS1/TCLKD/TIOC2B
203
PD6/D22/IRQ6/SSO1/TCLKC/TIOC2A
C125 204
VCC12
0.1u 205
R103
56 PD5/D21/IRQ5/SSI1/TCLKB/TIOC1B
DATA15 206
VSS12
4 5 207
DATA14
PVSS17
3 6 208
DATA13 TCOUNT
PD4/D20/IRQ4/SSCK1/TCLKA/TIOC1A
2 7 C115 209
DATA12
PVCC17
1 8 0.1u 210
DATA8
DATA9
1
2
8
7 211
PD3/D19/IRQ3/SCS0/DACK3/TIOC0D
PD2/D18/IRQ2/SSO0/DREQ3/TIOC0C
IC103
DATA10 3 6 212
213
PD1/D17/IRQ1/SSI0/DACK2/TIOC0B R5S72630P200FP
DATA11 4 5
PD0/D16/IRQ0/SSCK0/DREQ2/TIOC0A
D R108 IC102 DATA15 1
R110
8 214
D15 CORE:200MHz
DATA
56 C104
54 1 DATA14 2 7 215
D14
53 VSS3 VDD1 0.1u 216
2 DATA13 3 6
R104 DQ15 DQ0 PVSS18
52 3 C105 217
DATA4 1 8 DATA12 4 5
VSSQ4 V D D Q 1 D13
MAIN CPU
0.1u C116
DATA5 2 7 51 4 33 0.1u 218
DQ14 DQ1 C117 PVCC18
DATA6 3 6 50 5 VCG1063-A 219
DQ13 DQ2 R111 D12
C102 49 6 220
DATA7 4 5 DATA11 1 8
VDDQ4 V S S Q 1 D11
56 0.01u 48 7 DATA10 2 7 221
DQ12 DQ3 D10
47 8 DATA9 3 6 222
R105 DQ11 DQ4 D9
46 9 C106 223
DATA3 DATA8 4 5 SCH
VSSQ3 VDDQ2 D8
4 5 45 10 VCG1063-A C126 224
DATA2 33
DQ10 DQ5 VCC13
3 6 44 11 330p/50 225
DATA1
DQ9 DQ6 R112 D7
2 7 C103 43 12 226
DATA0 DATA7 1 8
VDDQ3 VSSQ2 VSS13
1 8 0.1u 42 13 227
56 DATA6 2 7
DQ8 DQ7 PVSS19 238: PC13/RD/WR
41 14 C107 228
DATA5 3 6
VSS2 VDD2 C118 D6 239: PC12/CKE
40 15
0.1u 229
DQMLU DATA4 4 5 0.1u
N.C/RFU LDQM C119 PVCC19 240: PC11/CASU/BREQ/AUDATA1
GNDD 39 16 WE VCG1063-A 230
UDQM WE 33 D5 1: P C 1 0 / R A S U / B A C K / A U D A T A 0
38 17 CAS 231
CLK CAS R113 D4
66MHz 37 18 232
RAS DATA3 1 8
PC7/WE3/DQMUU/AH/ICIOWR
CKE RAS D3
36 19 CS3 DATA2 2 7 233
A12 CS D2
PC6/WE2/DQMUL/ICIORD
35 20 ADRS14 DATA1 3 6 234

PC0/A0/CS7/AUDSYNC
A11 BA0 D1
PC5/WE1/DQMLU/WR
34 21 ADRS15 DATA0 4 5 235

A9 BA1 D0
33 22 ADRS11 236
PC4/WE0/DQMLL
A8 A10/AP 33 PVSS20
C120
E 32
A7 A0
23 ADRS1
C121
0.1u 237
PVCC20
31 24 ADRS2 VCG1063-A 238
PC9/CASL
PC8/RASL
A6 A1
PC3/CS3
PC2/CS2
30 25 ADRS3 CKE 239

PC1/A1
PVCC1
PVCC2
PVCC3
PVSS1
PVSS2
PVSS3
A5 A2
VCC1
VCC2
VCC3
VSS1
VSS2
VSS3
29 26 ADRS4 240
CS0
A10
A11
A12
A13
RD
A4 A3
A2
A3
A4
A5
A6
A7
A8
A9
28 27 C108
VSS1 VDD3 SCH
1
9
5
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
330p/50
K4S561632J-UC75 GNDD ADRS5
VCG1063-A
VCG1063-A
ADRS6
ADRS7
C127
R125
C132
C193
C139
0.1u
0.1u
0.1u
10k
V+3R3
C133
C134
0.1u
ADRS8
ADRS9
R116
R117
R120
R128
R129
R130
10k
10k
10k
10k
10k
10k
ADRS10
ADRS12
VCG1063-A
VCG1063-A
VCG1063-A
VCG1063-A
VCG1063-A
VCG1063-A
C187
C188
C189
C190
C191
C192
ADRS13
C129
C130
C137
VCG1063-A
C138
VCG1063-A
0.1u
0.1u
CKE
DQMLL
SDRAM(256M) GNDD
5
7
6
7
6
7
6
8
7
6
5
8
R188
R187
R132
R134
R135
R136
56
56
33
33
33
4
2
3
4
1
1
RX/XBY
DQMLU
DQMLL
F
CAS
RAS
CS0
CS3
WE
OE
ADRS10
ADRS11
ADRS12
ADRS13
ADRS1
ADRS2
ADRS3
ADRS4
ADRS5
ADRS6
ADRS7
ADRS8
ADRS9
CONTROL
D 1/4
ADRESS
68 CDJ-850
1 2 3 4
5 6 7 8
V+5R6
1SS352
D101
V+3R3
HN1C01FU(YGR) A
R147
R148
220k
(CONT1)
10k
FROM/TO BOARD IF BLOCK
R145 CONT1
Q101
4:11E
D 4/4
22k
Q101 R146
CONT2
HN1C01FU(YGR) 4:11E
22k
R601
56
(CONT2)
Q102
LTC124EUB
OSCILLATOR
R137
R139
22k
22k
C194 0.01u/16
V+3R3
C180
GNDD
CPU_AUDIO VCG1063-A
CPU-AUDIO
3:10G C170 0.1
D 3/4 IC105
CONTO
DATA_R
LRCK
DATA_L
BCK
PLAY
SRVLRCK
SRVSDATA
SRVSCLK
CONTI2
CONTI1
LPS1
LPS2
INSIDE
4Y
GND
8 7
TO SERVO BLOCK SERVO16M 4A
R169 9 3Y 6
2:7C 5Y
CLK_S_16M 3A
11 33 10 5
R172
5A
1M
(DA)
(DA)
2Y
11 4
D 2/4 6Y
2A
(DA)
12 3
6A
6
R197
R198
12
R173
1Y
33
33
13 2
1k
VCC
14
1A
1
X103
VSS1084-A B
TC74VHCU04FT
CH
18p CH
TO AUDIO BLOCK
AUDIO16M
C171
C173
R167
SCH
3:5C
18p
CLK_A_16M
33
330p/50 D 3/4
C140
C144
0.1u
0.1u
16.9344MHz
R140
R141
C150
10k
10k
GNDD
C136
C141
C146
0.1u
0.1u
0.1u
RT3T22M
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
Q107
USB VBUS SW
PF22/SSIWS1/LCD_VCPWC/AUDATA2
PVCC11
PF23/SSIDATA1/LCD_VEPWC/AUDATA3
PVCC10
VCC9
VCC8
VCC7
PVSS12
PVSS11
VSS8
VSS7
AUDIO_X2
AUDIO_X1
PF10/NAF2/LCD_DATA10/SD_CMD
PF16/FRB/LCD_DON
PF14/NAF6/LCD_DATA14/SD_WP
PF30/AUDIO_CLK
PF15/NAF7/LCD_DATA15/SD_CD
PF25/SSIWS2
PF28/SSIWS3
PF19/SSIWS0/LCD_M_DISP
PF11/NAF3/LCD_DATA11/SD_CLK
PF20/SSIDATA0/LCD_FLM
PF17/FCE/LCD_CL1
PF26/SSIDATA2
120
PF24/SSISCK2
PF27/SSISCK3
PF21/SSISCK1/LCD_CLK
PF18/SSISCK0/LCD_CL2
FROM BOARD IF BLOCK

AVSS
119 3 4 VBUS_B
PA7/AN7/DA1
RT3T22M
118 V+5R6 4:11F
PA6/AN6/DA0
D 4/4
Q104
117
1SS352
PA5/AN5 5
D103
R515
NM
116 C156
AVREF 6
115 0.1u R514 22k 2 Q107
3 4
PA4/AN4 RT3T22M
114 C157 0 R175 1
AVCC
113 0.1u
ADC 5
PA3/AN3
Q104
112
PA2/AN2 RT3T22M 6 GNDD
111 2
PA1/AN1
124: P F 2 9 / S S I D A T A 3 PA0/AN0
110
R155 1 C
109
10k
N
NM
123: P V C C 9 USBDVSS
C197
108 C152 GNDD
122: P B 1 2 / W D T O V F / I R Q O U T / R E F O U T / U B C T R G / A U D C K USBDVCC
C158
107 0.01u
USBAPVCC 0.1u
121: PVSS10
C159
Q109
106 VCG1063-A LTC124EUB
USBAPVSS
105 R156 GNDD
REFRIN USB_ABSEL VBUS
104 5.6k F
USBAVSS Low VBUS_B
103 C153 NM
USBAVCC Hi 5V
102 0.1u R516 (USB_DP) FROM/TO BOARD IF BLOCK
VBUS
DP
101 (USB_DP)
100 USBA_D_P
DM 4:11D
C160 (USB_DN)
99
USBDPVCC 0.1u
98
R150
10k
C161
VCG1063-A
OSCILLATOR USBB_D_P
4:11F
USBDPVSS
97
MD_CLK0 R157
96
NM R165 48.00MHz IC107 2 1
V+3R3
(USB_DP)
MD_CLK1 R158
R151 10k
D2+
D1+
95 C162 470 4 3
D 4/4
NM
R164
PVCC8 GND2
NM
10p CH
X2
C169
94 0.1u D+ S
USB_X2 3 10
93 1 2 GND VCC
USB_X1 GND1 4 9
X1
C167
92 D-
CH
X102 OE
D2-
D1-
9p
C174
PVSS9 5 8
0.1
ASS7099-A
(USB_DN)
IC103
91
VSS6
USBB_D_N
90 VCG1063-A R159 6 7
MD 4:11F
R5S72630P200FP VCC6
89 C154 10k
R160
GNDD
TS3USB30RSW
USBA_D_N
88 10k 4:11D
PB11/CTX1/IETXD
CORE:200MHz PB10/CRX1/IERXD
87
86
R152
USB_ABSEL
GNDD
(USB_DN) D
4.7k SH_STATUS
PB9/CTX0/CTX0&CTX1
85
4:11C
USB_VBUSON
USB_ABSEL D+,D- USB SW
PB8/CRX0/CRX0/CRX1
84 4 M Low USBB
MAIN CPU PE15/IOIS16/RTS3

PVSS8
83
82
SRVBUS3
SRVBUS2
K D 4/4 Hi USBA
PE14/CS1/CTS3
81 SRVBUS1
PE13/TXD3
80 C163
PVCC7
79 0.1u
RTC_X2
78
RTC_X1
77
PVSS7
D 4/4
76 R161
VSS5 TO BOARD IF BLOCK
75 R192 MAIN_XBUSY
PC14/WAIT 4:10B
C155 10k
74 0
VCC5
73 0.1u
SRVBUS0 L 5 FROM AUDIO BLOCK
PE11/CS6/CE1B/IRQ7/TEND1
PE12/RXD3
72
71
10k
R513
10k
R153
DSPDREQ
3:3C
USB_CDETFLG
D 3/4
PE10/CE2B/IRQ6/TEND0 4:11D
70 C185
PE9/CS5/CE1A/IRQ5/SCK3 PNL_XBUSY
0 R162 4:9C
69 SRVRST
PE7/FRAME/IRQ3/TXD2/DACK1
68 NM
SRVCCE 7
PE6/A25/IRQ2/RXD2/DREQ1
PVCC6
67
R199
10k
C164
0.1u
C165
10 D 4/4 Notes
NM is No Mount (STBY)
PE0/BS/RXD0/ADTRG
66 R193
VCG1063-A TSO
PE5/A24/IRQ1/TXD1/DACK0 CKSSYB***K F
10k
0
4:10B FROM/TO BOARD IF BLOCK
65 R511
PVSS6 SR CKSRYB***K F
R163
E
PE2/A21/SCK0
PE3/A22/SCK1
64 C183 TSI
PE4/A23/IRQ0/RXD1/DREQ0
10k 4:10C CH CCSRCH***J F
PE1/CS4/MRES/TXD0 63 R512 0
N M SCH SCH CCSSCH***J F
PE8/CE2A/IRQ4/SCK2
9
PLLVCC
PLLVSS
62 R154 SRVBCLK
ASEMD
PVCC3
PVCC4
PVCC5
PVSS3
PVSS4
PVSS5
To JTAG
EXTAL
CEHVAW***M F
VCC3
VCC4
VSS3
VSS4
XTAL
CKIO
61
RES
NMI
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
7A
RS1/16SS***J
A6
A7
A8
A9
10k
XASEMD
FROM OWN SHEET F RS1/16SS****F
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
49
50
51
52
60
45
46
47
48
53
54
55
56
57
58
59
C151
D RS1/16SS****D
0.1u
R177 C179
SR F RS1/10SR****F
SR RS1/10SR***J
0 VCG1063-A
C139
C145
R149
1/4W RS1/4SA***J
0.1u
0.1u
10k
D 2/4
R184
R142
CPU_SRV
NM
R170
10k
VCG1063A-T 1000pF/50V
10k
2:12B
R510
C147
0.1u
10k
V+3R3
P
C137
C138
VCG1063-A
D 4/4
C142
C143
VCG1063-A
IC104
0.1u
8
0.1u
100p/50
R191
C184
5 1 MAIN_XRST
SCH
GNDD
0
VCC INB
R179 2 R189 MAIN_XRST
INA 4:11C
NM R166 4 3
0
R178
OUT GND
470
R190
FROM BOARD IF BLOCK

NM F
0 SR
SR
X101
7
6
5
7
6
C166
C168
3 4 NM
NM
TSCK
X2
R135
R136
R138
R143
NC2
33
0.47u
10p CH
120
33
33
33
33
C148
R144
DBG_TxD
V+3R3_B GNDD
4:10C
D 4/4
2
3
4
4
1
2 1
1 NC1
X1
DSS1193-A
GNDD GNDD
F
DBG_RxD
CLK_66M
CLK_66M
DBG_TxD
ADRS10
ADRS11
ADRS12
ADRS13
ADRS14
ADRS15
ADRS16
ADRS17
ADRS18
ADRS19
ADRS20
ADRS21
C149
ADRS6
ADRS7
ADRS8
ADRS9
CH
DBG_RxD
9p
GNDD 33.00MHz
V+3R3_B
UART R171 JTAG_XRST
7A
V+3R3B N M SR
OSCILLATOR GNDD FROM OWN SHEET
GNDD
GNDD D 1/4
CDJ-850 69
5 6 7 8
1 2 3 4
A D 2/4 MAIN ASSY (DWX3174)

• SERVO Block
SERVO DSP
CPU-SRV
SRVSDATA
SRVLRCK
SRVSCLK
SPDLFG
SRVRST
SRVCCE
SRVBCLK
SRVBUS3
SRVBUS2
SRVBUS1
SRVBUS0
SRVSBSY
R295
R
SRVRST
R275 100
33
33
33
R296
R297
IO3B
IO2B
IO1B
IO0B
NM
0
R236
R237
R238
B GNDD GNDM
V+3R3_S
C222
0.1u
(DA)
R240
R241
R242
R243
R244
R246
22k
22k
22k
22k
22k
22k
C223
C231
0.01u
0.1u
C214
100u/6.3
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
DVSS3_1 76
CN201 IPF
DVR
RO
DVDD3_1
IO3B(LRCK)
IO1B(BCKI)
BUS3
BUS2
BUS1
BUS0
ZDET
BUCK
EMPH
DVSS3_2
IO2B(AIN)
IO0B(EMPHI)
VSS5
LRCK
LO
DKN1404-A
VDD5
AOUT
/CCE
BCK
C233
/RST
1 75
IPF
2 74 0.1u R
ST1- 1 ST1- (ST) SBOK XO
L201 SCH C275 3 73
ST1-
ST1- 2 SBOK CLCK XI
CTF1545-A 330p/50 4 72
ST1+ 3 ST1+ VDD3_1 75. X V D D 3 XVSS3
L202 (ST)
ST1+ C211 5 71
ST1+ 4 VSS3_1 TESIN
CTF1545-A VCG1063-A 6 100. D O U T 70 C234
R294
ST2- 5 ST2- (ST) DATA VDD3_2
L203 7 69 0.1u
ST2-
ST2- 6 SRVBSY SFSY VSS3_2
CTF1545-A VREF1R65 8 68
C ST2+ 7 ST2+
L204 (ST) 0.01u/16 9
SBSY FGIN
67 0 R293
C236
ST2+ C282
ST2+ 8 R229 IO0A(/HSO) MONIT
CTF1545-A 10 66 MONIT
10k
LO+ 9 LO+ (LO) IO1A(/UHSO) IO3A
L205 R291 IO1A 11 65 IO3A
LO+ AWRC
LO+ 1 0 ARSEL IO2A
CTF1545-A 12k F R290 12 64 IO2A
LO- 11 LO- C203 AWRC DMO
L206
(LO)
LO- 27k C212 13 IC201 63
LO- 12 47p SCH R230 PVDD3 FMO
GNDS CTF1545-A
CTF1545-A
R224 5.6k 0.1u 14 TC94A15FG 62
GNDS 1 3 PDO VREF
LPS2 L219 R208 47k R231 15 61
47 LPS2
LPS2 1 4 TMAXS TRO
LPS1 L220 R209 47 R225 150k 16 60
LPS1
LPS1 1 5 TMAX FOO
CTF1545-A 150k 17 59 C235
GNDS 1 6 LPFN AVDD3_2
V+5_P VREF1R65 R226 C205 18 58 0.01u
GNDS 1 7 VCG1063-A LPFO TEZI
C279 15k 0.015u 19 57
GNDS 1 8 PVREF TEI
2.2u/10
C 2 7 6 SQ
VCG1063-A
V+5P C210 20 56
V+5P 1 9 (TS) R292 VCOF SBAD
47u/6.3
C204
C260
C261
L207
0.01u
A_S2 NM 0.01u 21 55
0.1u
A_S2 S
A_S2 2 0 VCOREF
25. S L C O FEI
CN2305
CTF1545-A C206
C202
VR1R65 0.022u 22 54
VREF 2 1 DTCN 26. R F I RFDC
A_S1 (TS) L208 CTF1545-A C207 23 27. R F R P I 53
A_S1 0.022u
A_S1 2 2 DTCP 51. R F Z I RFRP
AVDD3_1
A_D (FS) L209 CTF1545-A 24 52

INVSEL
A_D
RFEQO
EQSET
RVDD3
TESTR
PNSEL
RVSS3
VMDIR
RESIN
RFDCI
A_D 2 3 PVSS3 AVSS3_1

(FS)
AGCI
L210 C208
FNI2
FNI1
A_C
FPI2
FPI1
25 51
VRO
RFO
LDO
CTF1545-A A_C
FTE
MDI
TNI
TPI
A_C 2 4
(FS) L211 1000p
D A_B 2 5
A_B CTF1545-A A_B
C232
GNDS
(FS)
32
33
34
26
27
28
29
30
31
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
A_A L212 CTF1545-A A_A
C
A_A 2 6 0.033u
PD L213 RF
CTF1545-A PD
PD 27
GNDS
C218
C219
C224
C230
GNDS 2 8
0.1u
0.1u
0.1u
0.1u
LD780 L214 FTE

LD780
LD780 2 9
GNDS 3 0
CTF1545-A
15 VREF1R65
(TS)
C215
C217
L215 C227
470p
AGCRF
TD
0.1u
CTF1545-A TD
0.015u
C220
C221
TD 31
0.1u
(TS)
C225
R247
TR L216 CTF1545-A 68p SCH TRACK
TR
10k
47u/6.3
TR 32 VCA
FD (FS) L217 CTF1545-A FD V+3R3_S
C216 R248
FD 33
(FS)
FR L218 680p LDO MDI 68k
CTF1545-A FR
FR 34
V C G 1 0 6 3 - A V+5_M
C 2 8 0 1000p
R235 14 V+3R3_S
R227
R228
R232
R233
GNDD 3 5 LD3S
22
22
22
22
RFO
C213
V+5M VREF1R65
0.1u
22k
47u/16
C228
V+5M 3 6
HU+ L221
13
N M SR
CTF1545-A HU+
R245
HU+ 3 7 2
8
HU- L222 R234 1
CTF1545-A HU- LDCHK Q201
HU- 38 2SA1036K(PQR)
HV+ L223 LD780 120
CTF1545-A HV+ 4
HV+ 3 9 3
HV- L224 IC203
CTF1545-A HV-
C209
HV- 40 PD NJM2903M
0.1u
HW+ L225
CTF1545-A HW+
HW+ 4 1 6
8
HW- L226 7
CTF1545-A HW-
E HW- 4 2
GNDS 4 IC2
GNDD 4 3 5
NJM2
U 44 U
L227
CTF1745-A U
U 45 GNDS
V 46 V
L228
CTF1745-A V
V 47
W 48 W
(FS)
(FS)
(FS)
(FS)
(TS)
(TS)
L229
CTF1745-A W
W 49
INSIDE V+3R3_S
INSW 5 0
R201
10k
A_S2
A_S1
O
A_C
A_A
A_D
A_B
R276
GNDD GNDS
PD
INSIDE
47
C201
0.1u
GNDS
F The > mark found on some component parts

indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts
of identical designation.
D 2/4
70 CDJ-850
1 2 3 4
5 6 7 8
SERVO DRIVER
D 1/4
CPU-SRV CPU_SR V
1:13J
SPDLFG
PWMLO
DRVMUTE1
DRVMUTE2
SPDLFG
PWMSL2IN
PWMSL1IN
TD
TR
FD
FR
LO+
TCOUNT
ADC
ST1+
ST2+
LO-
ST1-
ST2-
R295
V+5R6 V+5R6_M
NM
(LO)
L401
! IC206
R296
R297
NM
BA00BC0WFP NM
0
(LO)
(TS)
(FS)
(ST)
(ST)
GND
VDD
VIN
GNDD GNDM R250 V+5R6M
B
VC
C
NM 13
(TS)
(FS)
(ST)
(ST)
1
2
3
4
5
V+7R6_M
CLK_S_16M
V+3R3
C264 VCG1063-A
33k F 100k F 15k F
R287
47u/16
D 1/4
FROM CPU BLOCK
IC205
C272 330p/50
1:13C
1A
1 VCC 8
C263
R288
0.1u
3Y 2 7 1Y
0.01u
C252
V+7R6_M 2A 3 6 3A
R289
GND 4 5 2Y
R274
SCH
C256
0.1u
77
DVSS3_1 76
N M 1/4W TC7W04FU
GNDM
RO
DVDD3_1
C233 C246
75 47u/16
74 0.1u R249 C240 ADC 47u/16 C247
XO
73 NM NM C269
VREF1R65 GNDD
XI IC204
72 VREF1R65 N MSQ 1 54
3 XVSS3 N MSQ
71 3 C270 2
LDO- ACO1+ 53
R257
C242
R259
C243
330p
270p
SR F
R265
R272
R273
10k
10k
TESIN LDO+ ACO1-
10K
70 C234 C244 3 52
C259
68k
68k
R294
VDD3_2 R253 VCC ACO2+

NM
0.1u
69 0.1u 33k 0.1u 4 51 VREF1R65

VREF1R65
VSS3_2 A C T I N 1 ACO2-
68 VREF1R65 R254 5 50 R267 R270
VREF1R65
FGIN
0 R293 C273
A C T I N 2 ACO3+
NM F NM C
1/4W
1/4W
1/4W
1/4W
67 18k 6 49
SCH
C236
C239
C274
330p
NM
47u/6.3
0.01u
0.1u
R286
MONIT T J M O N ACO3- C257

22k
470p/50 C251
66 MONIT 7 48 C255
IO3A BTHC AVM 2200p CH
65 IO3A C248 8 47 1200p SR R271
1
DMO SPVM_S
C245
C262
0.01u
IO2A
0.1u
IO2A SCH ACTIN3 NM

R258
R260
R261
R262
64 9 46
DMO PGND1 LDIN LDIN C258
63 10 45 V+3R3_B
FMO PGND2 AGND 2200p CH
R266
44 C249
100p SCH 1 0 0 k
62 TACTHI 11
VREF U SPCNF
61 TRO 12 4 3 0.01u
TRO SPVM1 FG
60 13 42
C254
FOO V VC
SPDLFG
0.01u/50
C281
59 C235 14 41
SR
AVDD3_2 fin1 fin2
58 0.01u C238 FOO
15 40
TEZI PGND3 SLO1+
57 0.033u 16 39
TE
DRVMUTE1
TEI W SLO1-
56 17 38
DRVMUTE2
SBAD SPVM2 SLO2+
55 18 37
SBAD S
R255
FEI SPRNF SLO2-

SR
2.2k
54 19 36
RFDC FE HB SLGND
53 VREF1R65 20 35
I RFRP HU+ CTL2
52 C241 21 34 R263
AVSS3_1 HU- CTL1 2.7
R268
R269
51 0.033u EC 22 33 1/4W
10k
10k
FTE
TNI
TPI
SR HV+ SLRNF2 VCG1063-A

R252 C283
C232
GNDS 23
HV- SLRNF1
32 R264 2.2u/10 D
3 1 21
.7
49
50
N M SR 24 C268
/4W
N M SR
SL2IN
R256
0.033u HW+ SLVDD

RFRP SQ
25 30 GNDS
HW- SLIN2 C250
FTE
T 26
SPIN SLIN1
2 9 0.1u
C253
27 28
DGND DVCC SL1IN
15 VREF1R65 V+3R3_S
SPIN
BD7956FS
0.1u
R251
10k
SCH
R247
TRACK COUN T
10k
SQ
SR
SR
SR
VCA
R248
100p
GNDM
NM C277
C266
VCG1063-A C267
C271
68k V+3R3_S
C278
C265
TCOUNT
0.01u/50
2.2u/10
0.1u/16
1000p
2 GNDS
8
C237
1
0.1u
4 (DA)
3
NJM2903M
IC203
: Audio Data Signal Route
(FS)
6
8
7 GNDS : Focus Servo Signal Route
(TS) E
5
4 IC203
NJM2903M
: Tracking Servo Signal Route
(ST)
(LO)
: Stepping Motor Signal Route
GNDS
: Loading Motor Signal Route
Notes
(TS)
CKSSYB***K F : Waveform Measuring Point
SR CKSRYB***K F
CH CCSRCH***J F
: Voltage Measuring Point
A_S1
SCH CCSSCH***J F
CEHVAW***M F
HW+
HU+
HW-
HV+
HU-
RS1/16SS***J
HV-
W
U
F RS1/16SS****F
D RS1/16SS****D
SR F RS1/10SR****F
SR RS1/10SR***J
1/4W RS1/4SA***J F
VCG1063A-T 1000pF/50V
D 2/4
CDJ-850 71
5 6 7 8
1 2 3 4
A D 3/4 MAIN ASSY (DWX3174)

• AUDIO Block
AUDIO DSP
CPU_AUDIO
DSPRST
TO CPU BLOCK
DSPDREQ
D 1/4
DSP16M
1:13H
2
16.9344M
R358
D 1/4
CLK_A_16M V+3R3_A
1:13C F301
100
DTL1106-A
B Q
FROM CPU BLOCK
R351
1 3
100
330p/50
SCH
C340
C335
SQ
2.2u
2
R312
R313
R314
R315
C305
0.01u
SCH
10k
10k
10k
10k
V+1R25
GNDD
R308
R345
NM
R316
C308
C310
330p
0.1u
4.7k
F302
PE7
PE8
PE9
0.01u
NM
C307
PE10
PE11
1 3 DACCS
C341
C336
NM
SQ
2.2u
AUDIO_SCK
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
2
AUDIO_SO
PLLD_GND
PLLP_GND
PLLD_VDD
RESET_B
CORE_GND_3
SDO1_PE10
SDO0_PE11
PLLP_VDD
MODC_IRQC
MODD_IRQD
CORE_VDD_3
SDO4_SDI1_PE
SDO3_SDI2_PE
SDO2_SDI3_PE
EXTAL
MODA_IRQA
MODB_IRQB
SDO5_SDI0_PE
FST_PE4
PINIT_NMI
61 40 C311 GNDD ZERO
PE3
62 39 330p SCH
C301 63 38 DSPCS
SS_HA2
0.1u 64 37 AUDIO_SCK
SCK_SCL
65
HCKT_PE5
61: F S R _ P E 1 40: P L L A _ G N D
MISO_SDA
36 R320 AUDIO_SI JTAG
C 66 62: SCKT_PE3 39: P L L A _ V D D 35 33 AUDIO_SO
HCKR_PE2 63: SCKR_PE0 38: H R E Q MOSI_HA0
67 34
C O R E _ G N D _ 4 64: IO_VDD_4 TMS TMS
68
ADO_PD1
65: IO_GND_4
IC301 TCK
33
TCK
C302
69
70
ACI_PD0 DSPC56371AF180 TDI
32
31
TDI
CORE_VDD_4 TDO TDO
R301
0.1u
R307
71
72
HCKR_PC2
HCKT_PC5
76: S C K R _ P C 0
77: S C K T _ P C 3
DSP CORE_VDD_2
CORE_GND_2
30
29
C312
VCG1063-A
33 33 73
IO_GND_5
78: F S R _ P C 1 LVTTL TIO1_PB1
28 GNDD
79: F S T _ P C 4
C303 74 27
IO_VDD_5 80: S D O 5 _ S D I 0 _ P C 6 TIO0_PB0
BCK R302 0.1u 75 23: P F 1 0 26 C313
SDO4_SDI1_PC7
SDO3_SDI2_PC8
SDO2_SDI3_PC9
22: S C A N IO_VDD_3
33 0.1u
R303 76 25
CORE_GND_1
CORE_VDD_1
21: P F 9 IO_GND_3
SDO1_PC10
SDO0_PC11
33
LRCK R304 77 24 PLAY
IO_GND_1
IO_GND_2
IO_VDD_1
IO_VDD_2
R305 33 78 23 R317
33
DATA_L 79 22 22k
PF8
PF6
PF7
PF2
PF3
PF4
PF5
PF1
PF0
PF9
(DA) 80 21
1
10
11
12
13
14
15
16
17
18
19
20
D
C304
C306
0.01u
0.1u
C309
VCG1063-A
GNDD
R310
33
(DA)
DACLRCK
(DA) DACDATA (DA)
DACBCLK
CLK11M
E
DATA_R
Notes
CKSSYB***K F
SR CKSRYB***K F
CH CCSRCH***J F
SCH CCSSCH***J F
CEHVAW***M F
RS1/16SS***J
F RS1/16SS****F
D RS1/16SS****D
F SR F RS1/10SR****F
SR RS1/10SR***J
1/4W RS1/4SA***J
D 3/4 VCG1063A-T 1000pF/50V
72 CDJ-850
1 2 3 4
5 6 7 8
AUDIO DAC AUDIO FILTER
V+3R3_A V+5_A V+10_A V+5_A
VCG1063-A
N M SR
0 SR
100u/6.3
R339
R336
C343
NM
C328
ALO 33p CH
Lch
IC303 (1/2)
D 4/4
0.01u/16
47u/6.3
B
C342
C317
C318
C319
C320
C321
RNB4580F
0.1u
0.1u
C323 R325 R327 R330 3
4 R342
LOUT
180p CH
100u/6.3 220 D 2.2k D 3.3k D
4:11E
N M CH
1 NM
47k D
C324
C326
8
R323
2 TO BOARD IF BLOCK
GNDD GNDA
47u/16
R353
C332
C331
NM
NM
R332 R333
R322
11M
10k
IC302 4.7k D 5.1k D
16
MCLK
1 GNDA R356
BCKIN GNDA
S 15 2 47k D
ML DATA
_SCK 14 3
MC LRCKIN
_SO 13 4
MD GND
C339
12 5
NM
47u/16
R354
C330
C333
ZEROL Vdd C329
GNDA
NM
NM
R346 11 6
ZEROR Vcc 33p CH
Rch
0 10
9
V c o mV o u t L
7
8
C322 R326 R328 R331
IC303 (2/2)
RNB4580F
5
4
D 4/4
A G N DV o u t R R343 ROUT
22u/6.3
C314
C315
100u/6.3 220 D 2.2k D 3.3k D
180p CH
0.1u
GNDD 4:11E
7 NM
8
JTAG
CH
R324
C327
PCM1742KE 6
47k D
NM
C325
TO BOARD IF BLOCK
ARO
C316 C
1000p CH R329 R334
TMS V-AUDIO
GNDA GNDD 4.7k D 5.1k D
TCK (V-10_A)
R357
GNDA
TDI
47k D
TDO
(DA)
V+10_A V+12_EUP
MUTE
R340 D303
N MSR D 3 0 4
NM
NM
CURCUIT
N MSR
R344
(NO USE)
D 4/4 D
MUTE_CAP
4:11F
TO BOARD IF BLOCK
C334
NM
D 4/4 R349
4
(GNDD)
MAIN_XMUTE
4:11C 0 5
6 NM 3 GNDD
TO BOARD IF BLOCK
R352 Q302 R337
Q301
Q302 NM
NM 2 1 NM NM
D 4/4
R350
NM
V+3R3 R347
N M SR MUTE_A
(DA) (DA) 4:11E
4
R338
TO BOARD IF BLOCK
NM
5 R348 (GNDD)
C337
R341
C338
Q303 N M SR
NM
NM
NM
RT3T22M
3 6
2
1
GNDD V-AUDIO GNDD
(V-11_A)
GNDD E
MUTE
CPU_AUDIO
1:12B
D 1/4
: Analog Audio Signal Route

(DA)
: Audio Data Signal Route
: Waveform Measuring Point
: Signal Level Point F
D 3/4
CDJ-850 73
5 6 7 8
1 2 3 4
A
D 4/4 MAIN ASSY (DWX3174) (USB_DN)
• BOARD IF and POWER SUPPLY Block (USB_DP)
REGULATOR for PICK UP & SERVO

REGULATOR for CPU
5MON
1:5D
D 1/4
NM
TO CPU BLOCK
Q412
C476
NM
V+5R6 V+3R3 V+1R2 V+5R6 V+5_P V+5_M V+5R6 ! V+3R3_S
IC408
IC401 S-1170B33UC-OTS
IC404
VOUT
BA33BC0WFP BD00KA5WFP
NOISE_BYPASS
14
VIN
R401
R403
1/4W
1/4W 1/4W
NM
NM
! 9 ! IC405 CN401
GNDD
GND
GND
! AKM1299-A
VCC
OUT
OUT
5
4
CTL
CTL
ADJ
Vcc
R454
R456
NC
V3R3
10k
V1R2
5.6k
R404
CONTROL NB
R402
1/4W
NM
NM
3 4
2
3
1
V+7R6_M
1
2
3
4
5
1
2
3
4
5
GND 1
V3R3S
VSS
ON/OFF
10
NC
2
F
GNDM 2
R426
Vin Vout
SR
33k 1 5
R405
212
R413
GNDD
VCG1063-A
VCG1063-A
3
DCH1165-A
VCG1063-A
CN2004
VCG1063-A
0
0
R50
C421 SCH
C410 1u
SR
1u SR
C422
NJM2872BF05
100u/6.3
C403
C406
C408
C412
C495
C419
C400
22u/6.3
C402
GNDD
0.1u
0.1u
330p/50
F
C462
C418
0.01u
0
R427
C414
1u/10
0.1u
NM
R603
C425
NM
R406
C463
C415
R409
C465
NM
NM
NM
NM
GNDD 5
56k
1u
V+7R6_D 6
C473
V+7R6_D 7
3.3V 1.2V 5.0V GNDS GNDD GNDS
3.3V
GNDD REGULATOR GNDD REGULATOR REGULATOR REGULATOR GNDD 8
C431
E 1/2
47u/16
V+12 9
GNDD 10
V-10_A
V-10_A 11
REGULATOR for AUDIO DAC & AUDIO DSP REGULATOR for AUDIO DAC & AUDIO FILTER GNDA 12 V+10_A
V+10_A 13
C426
C429
V+5R6 V+3R3_A V+1R25
NM
IC402
S-1170B33UC-OTS
VOUT
IC403
4 VIN
BD00KA5WFP V+10_A V+5_A V-10_A V-AUDIO
! !
5
11
GND
!
OUT
GNDA
CTL
ADJ
V3R3
Vcc
V1R25
IC406
V5R6
3
16
2
1 5 17
VSS
NC
ON/OFF
2
3
4
5
Vin Vout
12 2
GND V+5A
R421
SR
33k F 22k F
R407
R415
3 NB 4
VCG1063-A
10u
1u
V-AUDIO
0
CONTROL
C
VCG1063-A
SR
C401
C405
C474
C407
C411
C467
C413
100u/6.3
NOISE_BYPASS
0.1u
22u/6.3
0.1u
1000p
C416
C417
0.01u
C404
C409
R422
NJM2872BF05
R408
C464
R416
C466
1u/10
NM
NM
NM
NM
1u
CH
C468
3.3V 1.25V GNDA
5.0V
GNDD GNDD
REGULATOR REGULATOR REGULATOR
V+12_IJO
V+12_IJO
R501
12k
F
V+1R2 V+1R25
V+7R6_M V+12 V+12_IJO
R502
V+5R6
1SS352
1SS352
10k
F
D406
D405
F
R410
R423
R435
R463
3.6k
NM
POWER DETECT
12k
27k
F
GNDD
R412 R425 R437
5.
D NM NM NM DC-DC C
Q402
2SA1576A(QR)
2SA1576A(QR)
2SA1576A(QR)
Q404
F
Q406
R411
R492
R424
R436
NM
12k
3.3k
F
F
11k
R414
R432
R444
100
100
100
NORMAL Hi
ABNORMAL Low
GNDD VDET
11C
GNDD GNDD Q410
NORMAL Low TO OWN SHEET
C423
LTC124EUB
0.1u
ABNORMAL Hi
R460
C420
NM
0.1u
V+12_IJO V+7R6_D
V+5R6 V+3R3_S V+3R3

GNDD
F
V+12_EUP 1/4W
R484
R483
10k
V+12_IJO
GNDD
D404
D403
R495
D402
NM
NM
NM
220
0
C475
C501
VCG1063-A
0.1u
Q414
R487
F
LTA124EUB
10k
R485
3.6k
Q415 V+12_IJO
GNDD
R494
100k
2SA1576A(QR)
R486
R491
100
Q413 PWR_ON
LTC124EUB
R458
11C;8A GNDD
15k
NM Q411
GNDD
C481
NM
E LSC4081UB(QR)
R461
NM
R459
R462
12k
10k
F
GNDD
V+12_IJO V+12_IJO
V-10_A
GNDD
V+1R2 Notes
R429
R446
V+1R25
10k
10k
NM
R431 R448
R417
R440
2.2k
2.2k
10k 10k
R420 R443 SR
Q405 Q408
HN1C01FU(YGR) HN1C01FU(YGR) CH
NM NM
SCH
R418
R441
10k
10k
R434
R453
100
100
F
GNDD GNDD D
F SR F
SR
1/4W
D 4/4
74 CDJ-850
1 2 3 4
5 6 7 8
(CONT1)
: Analog Audio Signal Route : CONTROL1 Signal Route
(USB_DN) (CONT2)
: USB_D_N Signal Route : CONTROL2 Signal Route A
(USB_DP)
: USB_D_P Signal Route : Voltage Measuring Point
SCH
V+12_EUP
FROM OWN SHEET
NM
Q412
PWR_ON
V+12_IJO
11C;2F
C476
NM
0.01u/16
NM
C452
C458
C504
C507
330p/50
0.1u/10
IC410
V+7R6_M
CN402
1 1A VCC 14 RKN1068-A
V+12_EUP
2
1B
4B 13
R503
D 1/4 C505
FROM CPU BLOCK

100 V+5R6 27 GNDD
CN401 V+7R6_D 3
4A
12 MAIN_XBUSY NM
KM1299-A GNDD 1:13H V+12 C469 26
1Y V+12_EUP
NM
C433
R471
1/4W
4 11
NM
2A C454
0
V+12 2B 25 GNDD
V+12
_M 1 4Y 10 R499 NM
5 3B NM
3A R602 24 GNDD
DM TSO R509 NM
2 6 9 R498 SR 0
1:13I 23 V+5R6
DD 2125 2Y C472
3 7 8 VCG1063-A
R508 GND
GNDM 0.01u C470 22 V+5R6
DD 4 3Y NM 0.1u C453
0
NM R504 21
R603
SCH330p/50 C506 GNDD

C425
C434 SCH
NM
DD 5 NM
SQ
C446 NM
100
R477 33
20 TSCK B
6_D 6 SCH
330p/50
2.2u/10
0.01u/16
19
C502
C435
GNDD
CN2002
6_D 7 C503 C487 100p/50
NM R476
33 L407 18 PNL_XBUSY
DD 8 C485
C431 SR GNDD CTF1545-A 220p/50
47u/16 SCH C490 17 TSO
+12 9 GNDD CTF1545-A 100p/50
L408 SCH C488 16 MAIN_XBUSY
0.1u/16
DD 10
SR
C436
V-10_A V+3R3 R479 100p/50

33 C486 15 TSI
0_A 11 R507
MAIN_XRST R473 100p SCH
14 MAIN_XRST
DA 12 V+10_A
D 1/4 1:15J 33 SR
E 1/2
0 IC411 TO CPU BLOCK C482
TO AUDIO BLOCK NM 13 GNDD
0_A 13 R482 R505
1 1A VCC 14 MAIN_XMUTE
D 1/4 1B
0 D 3/4 3:9F
12 MAIN_XMUTE
C426
C429
2 4B 13
NM
NM
NM
R496 11 GNDD
4A FROM OWN SHEET
PNL_XBUSY R419 3 12 R474
VDET
NM 6E 10 VDET
1:13H NM 41Y TSCK 33 SR
2A 11 R428
TO CPU BLOCK 9 GNDD
TO CPU BLOCK
2B 4Y TO OWN SHEET
5 NM R472
3B 10 1:10K
PWR_ON C489
R497 8 PWR_ON
GNDA GNDD 3A 2F;8A
6 9 33 SR
NM NM 7 GNDD
2Y TSI USB_VBUSON R480
7 8 R430
D 1/4
C483
GND 1:13G 6 USB_VBUSON
3Y NM 1:13I 33 SR
220p/50 5 GNDD
R506 USB_CDETFLG R481
C447
NM
0
D 1/4 FROM/TO CPU BLOCK
1:13H
33 SR
C484
4 USB_CDETFLG C
220p/50 3 GNDD
0.1u
NM (USB_DN) 2 USBA_D_N
USBA_D_N
GNDD GNDD 1:16G
CTF1701-
1 USBA_D_P
D 1/4 USBA_D_P
1:16F
(USB_DP) 22 33
11 44
F402
FROM/TO CPU BLOCK GNDD
CN403
RKN1058-A
2200p
C440
17 GNDA
GNDA
FROM AUDIO BLOCK
ROUT
5.6V
YB
D 750 F
16 ROUT
C441
3:12D
NM
R467
DC-DC CONVERTER 15 GNDA

C437
0.47u
D
R466
27k
LOUT
D 3/4 3:12C 14 LOUT
R468
CN2006
11k
13 GNDA
R464 (GNDD)
MUTE_A 12 GNDD
100 C432 3:12F R605
D
(CONT1)
R469
11 GNDD
8
0.1u/16
2.2k
COMP
CONT1 C492
EN
SS
FB
1:11A 0 10 CONT1
SCH
(CONT2) 100p/50 9 GNDD
FROM/TO CPU BLOCK
IC409
! CONT2 C493
DCH1165-A
DCH1165-A
VCG1063-A
BD9326EFJ CONT2
E 1/2
1:11A 8
GND
SCH
BST
V+7R6_D
VIN
SW
D 1/4
(USB_DN) 100p/50 7 GNDD

USBB_D_N F401
C424
C427
C428
C430
1
0.1u
4
1:16G
1
1/4W 6 USB_D_N
R483 (USB_DP)
USBB_D_P
0
V+5R6 8 1:16F 2
3 5 USB_D_P
L403 1/4W CTF1701- 4 GNDD
22u 2.5A R470 VBUS_B
C438 C494
0.1u 1:16D 3 VBUS_B
CTH1254-A-TLB 0
C439
RSX201L-30
100p/50 2 GNDD
D401
C448
47u/16
NM (GNDD) CH
MUTE_CAP
D 3/4 FROM AUDIO BLOCK
3:12F
R604
1 GNDD
0.1u/16
CH
SR
C471
C497
C498
C499
SR C461
GNDD
SCH 330p
0
C442
C443
C444
C496
C445
CH 1000p
SQ 2.2u
0.01u
DCH1165-A
DCH1165-A
0.1u
E
1000p
0.01u
GNDD GNDD
C449 NM C455 C480 0.1u

Notes
KN102 0.1u/16 C479 NM
NM is No Mount (STBY) NM
C450 NM C456 NM C478 0.1u
CKSSYB***K F
KN401
KN402
KN403
KN404
CKF1089-A
NM
NM
NM
NM
SR CKSRYB***K F 1 2 C477
1 1 1 1 C451 C457 NM
CH CCSRCH***J F C459 0.1u
1000p/50 C460 0.1u

SCH CCSSCH***J F
CH
CEHVAW***M F GNDD GNDD
RS1/16SS***J GNDA GNDD GNDD GNDM GNDD GNDS
F RS1/16SS****F
D RS1/16SS****D
SR F RS1/10SR****F
F
The > mark found on some component parts
SR RS1/10SR***J indicates the importance of the safety factor of the part.
1/4W RS1/4SA***J Therefore, when replacing, be sure to use parts
VCG1063A-T 1000pF/50V of identical designation.
D 4/4
CDJ-850 75
5 6 7 8
1 2 3 4
10.6 CMPX (1/2) and USBA ASSYS

R2085
E 1/2
CN2006
A
VKN1248-A NM
R2091 CMPX ASSY (DWX3153)
GNDD 17 R2098
NM
GNDD 16 0
NM
VBUS_B 15 VBUS_B
C2100
D2021 NM 2:2G
GNDD 14
TO
USB_D_P 13
1 F2003 NM
4
(USB_DP)
USBB_D_P
USB type B
Connector
E 2/2
CN403
USB_D_N 12 (USB_DN) 2:2G

2 3
GNDD 11 USBB_D_N
(CONT2) 2:2G
CONT2 10 CONT2 TO
2:2F
GNDD 9 (CONT1) Control
Connector E 2/2
CONT1 8 CONT1
D 4/4
2:2F
GNDD 7
R2086
GNDD 6
NM
GNDA 5
LOUT 4 ALOUT
2:2D TO
GNDA 3 Audio
JACK
E 2/2
B ROUT 2 AROUT
2:2C
GNDA 1
2:2E
TO
PNL_XMUTE
MAIN_XMUTE
MUTE
CIRCUIT
E 2/2
GNDA GNDD 2:2E

(USB_DN)
: USB_D_N Signal Route
(USB_DP)
: USB_D_P Signal Route V+5R6
VKN1258-A
CN2002
(CONT1) (USB_DP)
: CONTROL1 Signal Route
(CONT2) 27 USBA_D_P
: CONTROL2 Signal Route 26 USBA_D_N
: Voltage Measuring Point (USB_DN)
25 GNDD
24 USB_CODETFLG
: Signal Level Point GNDD
23
CN2003 22 USB_VBUSON
VKN1252-A
21 GNDD
!
CN402
C GNDD 21
P2004 466.375
20 PWR_ON
V+12_EUP 20 19 GNDD
1 2
GNDD 19 DEK1094-A 18 VDET
V+12 18 17 GNDD
V+12 17 16 MAIN_XMUTE
D 4/4
GNDD 16 15 GNDD
CN1001
VDET 15 14 MAIN_XRST
PNL_XMUTE 14 13 TSI
PWR_ON 13 12 MAIN_XBUSY
MAIN_XRST 12 11 TSO
USB_STOP 11 10 PNL_XBUSY
G
MAIN_XBUSY 10 9 GNDD
PNL_XRST 9 8 TSCK
GNDD 8 7 GNDD
PNL_CNVSS 7 6 V+5R6
GNDD 6 5 V+5R6
R2084
TSCK 5 4 GNDD
D NM
GNDD
GNDD 4 V+12_EUP 3
TSI 3 2 V+12_EUP
PNL_XBUSY 2 1 GNDD
TSO 1
CCG1221-A
C2097
10u/25
1 V+12_EUP
CTF1488
2 GNDD GNDD L2006
3 PNL_XRST
4 PNL_CNVSS V+7R6
CTF1488
GNDD 5 TSCK L2003
6 TSI
7 PNL_XBUSY NM
Q2034
8 TSO
NOTES
9 PWR_ON
NM NO MOUNT
CN2007
RS1/10SR***J KM200NA9 LTC124EUB
Q2021
J
GNDD
E RS1/10SR****D
C2089
NM
D
RST1/2SP***J For Panel UCOM DL
1/2W
CKSRYB***K
CCSRCH***J GNDD
CH
CEHVAW***M CN2001 L2005
1 V+12 B6B-XH-A
NM
GNDD GND for Digital L2001
2 1 6 V+12_EUP
CN2
GND for Analog CTF1488-A P2001

2
ACG1142-A
GNDA NM 5 V+12
C2012
10u/16
GND for Servo 4 V+12

GNDM
3 PWR_XON
O
2 GNDD
C
1
C2021
GNDM
0.1u/16
ACG1142-A
C2003
C2099
C2098
10u/16
NM
NM
CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE,

REPLACE WITH SAME TYPE No.466.375 MFD. BY GND
F LITTELFUSE INC. FOR P2004.
GNDD Th
ind
Th
E 1/2 of
76 CDJ-850
1 2 3 4
5 6 7 8
V+5_USB
V+5_USB
USBA_D_N
F USBA ASSY (DWX3156) DKB1106-A
JA2201
A
JH2201
USBA_D_P RT1
L2201
V+5_USB 1 (USB_DN) 1
NM NM USB
USBA_D_N 2
2 3 2 CONNECTOR
USBA_D_P 3
(USB_DP)
3 A TYPE
4
1 F2201 4
GNDD 4
VA2201
VA2202
C2201
VQW
RT2
C2202
100u/6.3
NM
NM
5
NNCD6.2MF
GNDD
0.01u/50
GNDD
CH
1000p/50
D2201
22u/16
51048-0500 GNDD
C2203
C2204
GNDF
GNDD GNDF
B
NOTES
V+5R6 V+5_USB
NM NO MOUNT
D2005
1SS352-TRB
7 CKSRYB***K
! USB CH
CCSRCH***J
VOUT
GND
IC2002
Over Current CEHVAW***M
VIN
NJM2845DL1-05
Protect CEHVQW***M
1
V+5_USB VQW
DCH1201-A
IC2003
C2033
C2036
GND for Digital

0.47u/10
GNDD
10u/10
BD2051AFJ
1 8 L2007
GND OUT3 GND for Frame
GNDF
NM
2 7 C2101 NM
IN1 OUT2
R2094
NM
4.7k
3 6
C2041
IN2 OUT1
USB_VBUSON GNDD 4 5
10u/10 *CAPACITORS
EN /OC Indicated in Capacity/Voltage(V)
C
V+5_USB USB POWER
R2018
R2099
NM
470
GNDD
R2015
10k
Q2033
RN1902
Q2033
RN1902
GNDD
52147-0510
CN2005
GNDD
5 GNDD
(USB_DP) 4 GNDD
CTF1701-A
3 USBA_D_P
(USB_DN) 2 3
2 USBA_D_N
1 F2001 4 1 V+5_USB
D
GNDD
7.6V&-11V DC-DC
V+12
CTF1488-A
L2006
V+12 V+7R6
CH
COMP
KM200NA13
C2014
V+7R6
CH
1200p/50
CN2004
R2001
C2013
L2016
EN
NM
NM
SS
FB
CTF1488-A
CTF1488-A
L2003
8
5
L2017
NM
1 V+7R6_M
C2017
GNDM
R2007
R2008
2
SI-8005Q
NM
NM
18k
GND2
!
IC2001
GNDD
9
CN401
4 GNDD 3
C2019
0.22u/16
5 GNDD
1
BS 2
4
GND1
SW
V+7R6_D
IN
7 V+7R6_D
E
D2001
C2009
50V
D 4/4
0.01u
NM
8 GNDD
9 V+12
CH 1000p/50
L2002
GNDD CTH1253-A
10u/25
10u/25
10u/25
R2002
68K D R2003
10
1/2W
15u
12
0
C2010
CCH1565-A
4
1u/16
C2015
11 V-10_A
100u/16
C2006
C2001
C2002
C2004
C2020
47u/16
0.1u/50
C2005
12 GNDA D2004
D R2004
L2005
CMS03
EP05Q06
D2002
CCG1221-A
CCG1221-A
CCG1221-A
C2007
13 V+10_A
2200p/50
NM
EP05Q06
D2003
0
C2011
NM
1u/16
R2005
0
CN2
D 4.7k
R2095
V+10_A
2200p/50
C2030
R2097
R2096
C2008
V-11
NM
R2006
47u/16
C2022
5.1k
O
V-11_A V-10_A
NM
C2021
C2029
0.1u/16
V-11
GNDD
GNDD GNDD GNDD

F
E 1/2 F
CDJ-850 77
5 6 7 8
1 2 3 4
10.7 CMPX ASSY (2/2)
A E 2/2 CMPX ASSY (DWX3153)

V+12 V+12_A
AUDIO FILTER and AMPLIFER Through
!
ANALOG POWER SUPPLY GENERATOR 5 V+10_
L2014 P2003 V+10_A
XTL3010-A 1 2
DEK1095-A
R2076
1/8W
1/8W
NM1/8W
NM1/8W
0466.500
2.7k
VCOM
R2033
UDZS6R2(B)
R2080
R2083
R2035
Q2028
2.7k
4.7k
2SB1698
D2019
R2030
NM
6
8
SQ
C2095
4
SQ
5
UDZS10(B)
Q2032
Q2029
C2092
IMX2
D2017
LTC143EUB
1u/16
C2052
NM
VCOM
R2082
10k
4.7u/16
3
Q2027 R2077
NM
LTA124EUB
Q2011
2.2k 1/8W
ACG1142-A
B 1/8W R2027 R2031

10u/16
V
C2090
R2079
4
0 1/8W NM 1/8W R2038
2.2k
SQ
UDZS10(B)
R2024
NM 1/8W
C2093
NM
C2094
D2018
R2092
47u/16
1/8W
GNDA 0
GNDA
CH
4.7u/16
SQ
C2054
Q2026
Q2030
IMT2A
NM
R2081
LTC143EUB
ACG1142-A
1u/16
GNDA
C2091
10u/16
C2096
2.2k
GNDA
R2078
1/8W
3
2.2k
6
Q2031
L2015
2SD2662 Q2012
XTL3010-A NM
V-11 V-11_A V-10_A
R2037
NM
C AROUT V-10_A
E 1/2 1:5B
ALOUT
FROM CN2006 1:5B
V+10_A
NM 1/8W
NM 1/8W
R2032
R2034
2
V+12_EUP 8
1
R2028
NM
MUTE
4
PANEL_XMUTE
CURCUIT 3
NM 1SS355
R2072 D2016
(MAIN_XMUTE)
C2051
Low HiZ Hi
MUTE_HOST
NM
Low MUTE - MUTE
1
HiZ MUTE MUTE OPEN
Q2010 V-10_A
Hi MUTE - OPEN NM
R2026 R2029 R2036
VW 470u/16
5
0 1/8W NM 1/8W NM 1/8W
C2088
R2093
4
R2025
FROM CN2003 Q2019

NM
R2075 UMD2N
CH
C2053
PNL_XMUTE 0
NM
1:5B 5
D E 1/2 MAIN_XMUTE
22k Q2019
UMD2N
6 3
R2068
Q2018
GNDD
GNDA
1:5C
2
2SA1576A(QR) GNDA
1 22k
FROM CN2002
I 4.7k
R2073
AMUTE
R2070
10k
R2074
H
C2086
R2071
C2087
0.01u/50
NM
NM
1M

(USB_DN)
R2069
: USB_D_N Signal Route

10k
R2088
22k
(USB_DP)
: USB_D_P Signal Route GNDD
(CONT1)
: CONTROL1 Signal Route
(CONT2) V-11_A
: CONTROL2 Signal Route GNDD
E : Signal Level Point

(CONT1) (CONT1)
CONT1
1:5B
(CONT2) (CONT2)
CONT2
1:5B
(USB_DN)
E 1/2 USBB_D_N
1:5B
USBB_D_P
FROM/TO CN2006 1:5A
(USB_DP)
VBUS_B
1:5A
*CAPACITORS
F Indicated in Capacity/Voltage(V)
CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, The > m
*RESISTORS
REPLACE WITH SAME TYPE No.466.500 MFD. BY indicates
unless otherwise noted. k k , M M . Therefore
LITTELFUSE INC. FOR P2003.
E 2/2 of identic
78 CDJ-850
1 2 3 4
5 6 7 8
NOTES
A
NM NO MOUNT
RS1/10SR***J
FER Through RS1/8SQ***J
1/8W
V+10_A
V+10_A CKSRYB***F
CKSQYB***F
1/8W
NM SQ
CH
C2057
R2051
C2063
NM
C2069
CCSRCH***J
CH
NM1/8W
NM1/8W
0
R2033
C2058
R2035
NM 1/8W NM CFHXSQ***J
CFHXSQ
NM R2046 6
8 GNDA
6
8 GNDA 7 CEHVAW***M
7
IC2006
IC2005 4
NM CEHVW***M
R2048 5 VW
4 NM 0 1/8W
5
0 1/8W
NM 1/8W
CH
GNDD GND for Digital
R2089
NM
R2052
C2064
NM
C2060
GND for Analog
C2070 GNDA
1
NM
NM GND for Frame

C2059 GNDF
NM
GNDA
GND for the earth point pin B
V-10_A GNDF1 of the PinJack
5
R2038
GNDA V-10_A GNDA
R2092 NM 1/8W
150
V+10_A C2075 R2061 R2066
220u/10 VW 150 1/8W 1/8W
R2059
R2040
R2042
47k
EARTH POINT TYPE
1/8W
NM
NM
2SD2704K
1k
Q2016
R2063
JA2003
Q2012
CFHXSQ
NM AKB7181-A
470p/50
2SD2704K
C2082
Q2014
R2055 D2011 R OUT
Q2012 1
NM
Q2013
1k 1SS352 2 AUDIO
NM
Q2013 NM L OUT 3 OUT
R2037
NM
CFHXSQ
2SD2704K
R2056 D2012
R2039
R2041
V-10_A C
Q2015
NM
NM
C2083
470p/50
1k
1/8W
1SS352
CH
V+10_A
R2049
C2061
NM
2SD2704K
V+10_A C2084 0.01u/50
V-10_A
Q2017
0
NM
1/8W
R2064
R2060
NM 1/8W
47k
1k VA2001
NM 1/8W
NM 1/8W
R2045 IC2006
2
R2034
8 C2076 R2062 R2067

2 1
8
1 IC2005
NM VW 150 1/8W 150 1/8W
NM 4 220u/10
R2047 3
4
3 0 1/8W GNDA GNDF GNDF1
NM 1/8W
0 1/8W
CH
R2050
C2062
R2090
NM
3
V-10_A
Q2010 V-10_A
NM R2087
R2036
4
GNDA NM
NM 1/8W GNDA GNDF
R2093
0.1u/50
0 C2102
D
GNDA GNDD
AMUTE
(CONT1)
JA2002
VKB1243-A
CONT1 R2058 270 2
470 R2065 3
CONT2 (CONT2) 1 CONTROL
0.01u/50
C2079
C2074
C2077
C2078
0.1u/50
0.01u/50
C2080
0.01u/50
0.1u/50
D2014
NNCD6.2MF
GNDD
E
(CONT1)
(CONT2) R2057
(USB_DN) 100
C2073
R2100
1u/16
22k
JA2001
(USB_DP) DKN1237-A
R2053 GNDD
RT1
NM V+5DETD
F2002
R2054 11 44 1
USBB_N
NM
2 USB CONNECTOR
22 33 USBB_P
GNDD
3 B Type
NM
NM
4
D2020
C2081
NM
RT2
VA2002
NM
VA2003
NM
GNDD
F
of identical designation. GNDD
E 2/2
CDJ-850 79
5 6 7 8
1 2 3 4
10.8 DFLB ASSY

R1049 R1055 R1058
R1187 3.3k 3.9k 5.6k
VSG1024-A
VSG1024-A
A 100
S1008
S1009
S1011
V+6R6 Vf=2.2V If=4.4mA W=19.4mW S1007
D1001
R1003
1k
Q1001 FL HOLDER DNF1862-A VSG1024-A
100
S1001
R1185
BROWSE_SW PLAYLIST_SW INFO_SW UTILIT

VSG1024-A
(AMBER) DEL1069-A
PC GNDD
LTC124EUB
DATA FL V1001
BIASIING CIRCUIT FOR FILAMENT POWER SUPPLY
21
R1001
F+
3.3k
C1062
PGND
LGND
Q26G
Q27G
V+6R6_FL 10u 10V
VDD
NC1
NC2
NC3
NC4
NC5
NC6
CLK
V+6R6_FL
27G
26G
LAT
40 F+1
41 F+2
42 F+3
F-1
F-2
F-3
VH
BK
Vf=2.2V If=18.7mA W=41.2mW
SI
S1002 DCH1201-A
D1002 C1063
10
11
12
13
14
29
30
31
32
33
34
35
36
37
R1004
10u 10V
1
2
3
6
7
8
9
Q1002
VSG1024-A 470 V+3R3_SW DCH1201-A
F
R1008
4
C1070
R1142
(GREEN) C1071
2SC4081(QRS)
2SC4081(QRS)
C1073
1u
C1017
2.7k
470
LTC124EUB NM NM
USB V+38
0.1u C1079 D1024 R1143
R1129
R1126
GNDD
100
100
R1002
Q1017
Q1016
0.1u 10
3.9k
R1164 NM Q1022
Vf=2.2V If=18.7mA W=41.2mW

R1019 R1023
1 NM
2SA1576A(QR)
LTC1
S1003
D1003 10 10 3 R1165 GNDD
Q1021
R1144
R1010
1k F
10k 2SD1898(PQ)
C1007 C1022 R1166
Q1003
V+3R3_SW
R1131
R1128
VSG1024-A 470
33k
33k
R1011 0.1u 22p CH NM
24
24
24
24
24
(GREEN)
BROWSE_LED
C1023
R1130
R1127
R1092
100k
100k
GNDD
B
R1145
R1146
R1147
R1148
R1149
470 22p CH 10k
LTC124EUB
DISC_LED
R1132
R1133
DISC
USB_LED
3.9k
3.9k
PC_LED
D_SCLK
D_DSO
GNDD
D_LAT
2
D_BK
KEY3
KEY4
SA
SA
SA
SA
SA
GNDD
GNDD
LOOPIN LED LOOPOUT LED RELOOP LED

V+12_EUP (AMBER) (AMBER) (AMBER)
Vf=2.2V If=4.4mA W=19.4mW V+6R6 f=2.2V If=4.4mA W=19.4mW V+6R6 Vf=2.2V If=2.0mA W=8.8mW V+6
V+12
CN1001 SLI-343Y8C(KLMN) SLI-343Y8C(KLMN)
SLI-343Y8C(KLMN)
D1012 R1060
VKN1252-A Q1006 2.2k
Q1004 Q1005 LTC124EUB
LTC124EUB D1007 R1029 LTC124EUB R1050
GNDD 1 1k D1010 1k
V+12_EUP 2
GNDD 3
GNDD GNDD GNDD
V+12 4 S1005 S1006 S1010
V+12 5
LOOPOUT_SW
GNDD 6
CN2003
RELOOP_LED
RELOOP_SW
DSG1079- DSG1079- DSG1079-
LOOPIN_SW
VDET
VDET 7
OUT_LED
PNL_XMUTE LOOP IN GNDD LOOP OUT GNDD RELOOP
IN_LED
PNL_XMUTE 8
PWR_ON
PWR_ON 9
C MAIN_XRST 10
MAIN_XRST
USB_STOP
USB_STOP 11
PLAYLIST_LED
BROWSE_LED
PC_LED
USB_LED
DISC_LED
USB_ACT_LED
1KEY_SW
2KEY_SW
4KEY_SW
8KEY_SW
1KEY_LED
2KEY_LED
4KEY_LED
8KEY_LED
REV_LED
SHIFT_SW
REV_SW
CUE_SW
PLAY_SW
CUE_LED
PLAY_LED
USB_STOP
LOOPIN_SW
IN_LED
LOOPOUT_SW
OUT_LED
RELOOP_LED
RELOOP_SW
MAIN_XBUSY
MAIN_XBUSY 12
E 1/2
PNL_XRST
PNL_XRST 13
GNDD 14
PNL_CNVSS
PNL_CNVSS 15
DCH1201-A
GNDD 16
R1182
R1181
R1180
R1033
R1026
R1031
R1027
C1076
C1032
R1034
R1035
R1036
R1039
TSCK
100
100
10k
10k
10k
10k
TSCK 17
0.1u
10k
10k
10k
10k
V+3R3_EUP
GNDD 18
10V
TSI
R1013
R1014
R1015
R1017
R1020
TSI 19
R1134
R1040
R1061
PNL_XBUSY
10k
10k
10k
PNL_XBUSY 20
10u
TSO
TSO 21 L1008
CTF1579-A
22k
22k
22k
22k
22k
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
VCC2
P3_0/A8(A8/D7)
VSS2
P1_4/D12
P2_4/INT6/AN2_4/A4.(A4/D4).(A4/D3)
P2_5/INT7/AN2_5/A5.(A5/D5).(A5/D4)
P2_0/AN2_0/A0.(A0/D0).A0
P2_1/AN2_1/A1.(A1/D1).(A1/D0)
P2_2/AN2_2/A2.(A2/D2).(A2/D1)
P2_3/AN2_3/A3.(A3/D3).(A3/D2)
P2_6/AN2_6/A6.(A6/D6).(A6/D5)
P2_7/AN2_7/A7.(A7/D7).(A7/D6)
P1_6/INT4/IDW/D14
P1_7/INT5/IDU/D15
P1_5/INT3/IDV/D13
INFO_LED 81
P3_1/A9
P3_2/A10
P3_3/A11
P3_4/A12
P3_5/A13
P0_7/AN0_7/D7 P4_4/CTS7/RTS7/C
S1004 UTILITY_LED 82
P0_6/AN0_6/D6 P4_5/CLK7/C
R1184
KEY2 83
TIME P0_5/AN0_5/D5 P4_6/PWM0/RXD7/SCL7/CS
C1012
100
P3_6/A14
P3_7/A15
P4_0/A16
P4_1/A17
P4_2/A18
P4_3/A19
VSG1024- KEY3 1000p CH 84
C1013 P0_4/AN0_4/D4 P4_7/PWM1/TXD7/SDA7/C
D KEY1 1000p CH 85
P1_2/RXD6/SCL6/D10
P1_3/TXD6/SDA6/D11
P0_3/AN0_3/D3 P5_0/WRL/W
P1_0/CTS6/RTS6/D8
C1011
GNDD KEY4 1000p CH 86
P0_2/AN0_2/D2
P1_1/CLK6/D9
C1014 P5_1/WRH/BH
KEY0 1000p CH 87
V+6R6 P0_1/AN0_1/D1 P5_2/R
R1012
C1010
3.3k
TCH/REL 1000p 88
C1009
CH
P0_0/AN0_0/D0 IC1007 ! P5_3/BCLK
1000p CH 89
E P10_7/AN7/KI3 DYW1795- /J P5_4/HL
P7_1/RXD2/SCL2/SCLMM/TAOIN/TB5IN
USB_ACT_LED R1163
PWR_SW 10k 90
(R5F363AENF-U0)
P7_0/TXD2/SDA2/SDAMM/TA0OUT
C1072 P10_6/AN6/KI2 P5_5/HO
USB_STOP 0.1u 91
A P10_5/AN5/KI1 P5_6/ALE
P9_4/DA1/TB4IN/PWM1
P9_3/DA0/TB3IN/PWM0
P7_3/CTS2/RTS2/TA1IN/V
1KEY_SW EUP_LED1 92
Service Part No.
P9_6/ANEX1/SOUT4
P7_2/CLK2/TA1OUT/V
P9_5/ANEX0/CLK4
P10_4/AN4/KI0 P5_7/RDY/CLKOUT
2KEY_SW EJECT_LED 93
PEG799A8
P7_4/TA2OUT/W
P10_3/AN3/KI7 P6_0/RTCOUT/CTS0/RT
JUMPER
P7_5/TA2IN/W
4KEY_SW VINYL_LED 94
P10_2/AN2/KI6 P6_1/CLK0
8KEY_SW MT_LED 95
1KEY_LED 96
P10_1/AN1/KI5
PANEL CPU P6_2/RXD0/SCL0
AVSS P6_3/TXD0/SDA0
2KEY_LED
P8_0/TA4OUT/U/RXD5/SCL5
97
P7_6/TA3OUT/TXD5/SDA5
P9_2/TB2IN/PMC0/SOUT3
P8_1/TA4IN/U/CTS5/RTS5
P10_0/AN0/KI4 P6_4/CTS1/RTS1/CTS0/CLKS1
P9_1/TB1IN/PMC1/SIN3
4KEY_LED GNDA 98
VREF P6_5/CLK1
P8_5/NMI/SD/CEC
P9_0/TB0IN/CLK3
P7_7/TA3IN/CLK5
8KEY_LED C1015
99
P8_4/INT2/ZP
P8_6/XCOUT
AVCC P6_6/RXD1/SCL1
P8_7/XCIN
P8_3/INT1
P8_2/INT0
REV_LED 0.47u
100
CNVSS
RESET
G H
P9_7/ADTRG/SIN4 P6_7/TXD1/SDA1
XOUT
VCC1
BYTE
VSS1
XIN
SHIFT_SW C1008
0.1u
REV_SW
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
V+3R3_EUP
C1016
KEY2_B
E
R1151
100u/10
R1059
100
PLAY_SW L1001
R1079 100
10k
10k
18
CH
C1038
PLAY_LED CTF1579-A
C1029
R1073
C1018
C1019
C1064
C1065
C1066
CH 1000p
CH 1000p
CH 1000p
CH 1000p
CH 1000p
0.1u
C1005
47p
CUE_SW DCH1201-A
10u/10V
CUE_LED
5 6
47p CH
GNDD
R1032
CTF1378-A
R1084
R1085
C1040
L1004
4.7k
47
47
V+6R6 GNDD
V+12 V+38 V+3R3_SW
X1001
GNDD C
JOG2 CTF1378-A
27p CH
CH
ENC_SW R1183
L1012
C1025
C1028
220
V+3R3_EUP
PNL_CNVSS
27p
R1037
F
JOG_SW
J_SCLK
D
J_DSO
ENC_2
ENC_1
4.7k DSS1166-A
J_LAT
ADCT
JOG1
ADIN
J_BK
CN1002 GNDD 15.975MHz

10
11
12
13
1
*CAPACITORS VKN1273-A
Indicated in Capacity/Voltage(V) GNDD
GNDD
GNDD
JOG1
JOG2
JOG_SW
J_DSO
J_SCLK
J_LAT
GNDD
V+3R3_SW
J_BK
V+12
V+38
unless otherwise noted. u F,p pF

PNL_XRST
V+3R3_EUP V+38
*RESISTORS IC1004
R1179
unless otherwise noted. k k ,M M . 5 1
VDD 0
ER
R1172
RESET 2 CHIP
SUB JUMPER
F J CN1802
4 3
R1071
VOUT GND
100k
R1173
C1035
C1036
0.01u
0.1u
BD45302G
G
G GNDD
RESET IC
GN
80 CDJ-850
1 2 3 4
5 6 7 8
R1055 R1058 R1065 R1077
3.9k 5.6k 10k 22k : Waveform Measuring Point

G DFLB ASSY (DWX3152)
VSG1024-A
VSG1024-A
VSG1024-A
VSG1024-A
A
C1039
S1009
S1011
S1012
NM
S1015
V+6R6
_SW INFO_SW UTILITY_SW BACK_SW ADD
PLAYLIST_SW
GNDD
OWER SUPPLY
R1066
R1070
R1081
R1087
R1094
R1097
R1099
R1100
680
680
680
680
680
680
680
680
21 F+
6.6V DCDC C1050
R1107 0.01u
SLI-343M8C(FGHJ)
SLI-343M8C(FGHJ)
SLI-343M8C(FGHJ)
SLI-343M8C(FGHJ)
D1013 22k
D1014
D1015
D1016
CH
C1058
C1053
C1055
1800p
R1118
8
NM
NM
10k
V+6R6
EN
SS
COMP
FB
22
Q1009 Q1011 Q1012 Q1013
SI-8105QL
R)
IC1006
LTC124EUB LTC124EUB LTC124EUB LTC124EUB V+12 V+6R6_FL
R1117
12k
Q1021 !
898(PQ)
GND
20
SW
CTF1378-A
CTF1579-A
BS
IN
L1009
L1007
24
24
24
24
PLAYLIST_LED
BROWSE_LED PLAYLIST_LED INFO_LED UTILITY_LED

BROWSE_LED
4
6.6V
UTILITY_LED
R1147
R1148
R1149
(GREEN) (GREEN) (GREEN) (GREEN) B

INFO_LED
Vf=2.2V If=12.9mA Vf=2.2V If=12.9mA Vf=2.2V If=12.9mA Vf=2.2V If=12.9mA

W=28.5mW W=28.5mW GNDD W=28.5mW W=28.5mW
CTF1579-A
SA
SA
SA
SA
C1049
L1010
D1017
NM
0.01u GNDD
L1006
ACG1128-A
ACG1128-A
RELOOP LED
CH
DTL1185-A
10u/16V
10u/16V
C1042
C1045
C1041
C1047
56k D
0.1u
R1114
SQ 12 SP
(AMBER)
R1109
CMS03
Vf=2.2V If=2.0mA W=8.8mW
1000p
V+6R6
D1018
SLI-343Y8C(KLMN)
< CALL CALL > DELETE MEMORY
ACG1128-A
DCH1324-A
D1012 R1060
10u/16V
120u/10V
C1057
C1059
C1060
C1061
Q1006 2.2k
C1048
NM
NM
1.5k D
TC124EUB R1072 R1088 R1095
R1115
1000p
3.3k 3.9k 5.6k
R1186
100
VSG1024-
VSG1024-
VSG1024-
4.7k D
S1014
S1016
S1017
R1116
GNDD
S1010
S1013 GNDD
VSG1024-
RELOOP_SW
DSG1079-
GNDD V+12_EUP
RELOOP
GNDD V+3R3_EUP
KEY1
!
IC1001 L1002 L1003 C
DTH1206-A CTF1579-A
D
8 1
CUE_LED
PLAY_LED
USB_STOP
LOOPIN_SW
IN_LED
LOOPOUT_SW
OUT_LED
RELOOP_LED
RELOOP_SW
330u
CD CS
R1042
3.3k
7 2
CH
ZL
SI ES
SA
C1027
C1024
R1021
6 3
V+ CT
DCH1201-A
DCH1201-A
220p
56p CH
R1043
5 4
2.7
10u/10V
10u/10V
C1030
220u/6.3
C1031
C1034
33k
IN- GND
NJM2392M
R1182
R1181
R1180
R1027
100
100
100
EP05Q06
ACG1128-A
10k
D1009
R1044
10u/16V
C1004
C1006
22k
D
68u/16
ZL
R1134
R1040
R1061
R1063
10k
10k
10k
10k
EUP POWER SUPPLY 3.3V DCDC GNDD

59
58
57
56
55
54
53
52
51
V+3R3_EUP V+3R3_SW
50
P3_2/A10
P3_3/A11
P3_4/A12
P3_5/A13
P4_4/CTS7/RTS7/CS0 V+3R3_EUP
19
R1154
49
0
P4_5/CLK7/CS1
48
P4_6/PWM0/RXD7/SCL7/CS2
B
R1104
R1108
R1110
47 S1018
P3_6/A14
P3_7/A15
P4_0/A16
P4_1/A17
P4_2/A18
P4_3/A19
10k
10k
10k
P4_7/PWM1/TXD7/SDA7/CS3 R1067 YSD5019-A Q1018

46 R1152 D
C1067
CE
0.47u
10k
P5_0/WRL/WR ENC_SW 3 1 1 6
45 4.7k R1124 PWR_ON D1 D4
P5_1/WRH/BHE R1150 220 2 5
44 R1123 VDET
P5_2/RD R1105 V+38 R1153 D2 D3
10k 220 ENC_1 4 2 Q1020 3 4
43 R1122 PNL_XMUTE LTC124EUB
P5_3/BCLK 10k G S
220 R1188 1k
42 R1125 MAIN_XBUSY R1106 5
ENC_2
P5_4/HLDA 220 2.2k RTQ040P02
R1155
P7_1/RXD2/SCL2/SCLMM/TAOIN/TB5IN
EPM
C1068
NM
NM
41 10k
C1044
C1046
R1069 GNDD
0.01u
0.01u
P7_0/TXD2/SDA2/SDAMM/TA0OUT
P5_5/HOLD 47k
40 R1121 MAIN_XRST ROTARY SEARCH
V+3R3_SW SUPPLY
P5_6/ALE 220
P7_3/CTS2/RTS2/TA1IN/V
39 R1083 D_LAT Q1019

P7_2/CLK2/TA1OUT/V
P5_7/RDY/CLKOUT 100
38 R1082 D_BK GNDD LTC124EUB
PWR_ON R1158
P7_4/TA2OUT/W
P6_0/RTCOUT/CTS0/RTS0
P7_5/TA2IN/W
100 L1011
37 R1089 D_SCLK 0
R1156
C1069
P6_1/CLK0
NM
NM
220 CTF1334-A
36 NOTES
P6_2/RXD0/SCL0 C1021
35 R1090 CH 47p D_DSO NM means STANDBY
P6_3/TXD0/SDA0 100 C1074
P8_0/TA4OUT/U/RXD5/SCL5
34 R1074 CH 47p PNL_XBUSY V+3R3_EUP

P7_6/TA3OUT/TXD5/SDA5
RS1/10SR***J
P8_1/TA4IN/U/CTS5/RTS5
P6_4/CTS1/RTS1/CTS0/CLKS1 100
33 R1075 L1005
TSCK
GNDD
P6_5/CLK1
RS1/10SR****D
P7_7/TA3IN/CLK5
22 CTF1357-A
32 R1076 TSO D
P6_6/RXD1/SCL1 22 Q1014
C1043 RS1/10SR****F
31 R1080 CH 47p TSI EUP_LED1 LTA124EUB F
P6_7/TXD1/SDA1
100 C1075
CH
CH
CH 47p RST1/2SP***J
C1078
C1077
V+6R6 SP
22
23
24
25
26
27
28
29
30
220p
100p
GNDD RS1/4SA***J
PWR_SW
SA
PWR_SW
E
JUMPER
R1059
CKSRYB
100
R1079 100
GNDA
10k
CH
C1038
ADIN CKSQYB
ADIN SQ
R1073
47p
ADCT
ADCT CCSRCH
CH
V+3R3_EUP
CEHAS
MT_LED
47p CH
MT_LED
CTF1378-A
R1084
C1040
L1004
CEHAZL
47
47
V+6R6 ZL
VINYL_LED
VINYL_LED
G L
KEY0
KEY0
JOG2 CTF1378-A
L1012
GNDD
TCH/REL
TCH/REL
F
JOG_SW
EJECT_LED
J_SCLK
EJECT_LED
J_DSO
JOG1
J_BK
EUP_LED
VDET
V+38 V+6R6_FL V+3R3_SW

GNDD GNDA
D
R1179
Q1024
R1175
1
33k D
4.7k
Q1023
0
2SA1576A(QR)
ER
R1172
Q1025
2SA1576A(QR)
2 CHIP LTC124EUB
UB JUMPER
3
F
R1071
ND
D
100k

R1176
R1173
R1177
R1174
4.7k
100
100
3.3k
2G
C
GNDD
G
CDJ-850 81
5 6 7 8
1 2 3 4
10.9 KSW1 and KSW2 ASSYS
A G H JUM
PLAY_LED
8KEY_LED
SHIFT_SW
NOTES
PLAY_SW
CUE_LED
REV_LED
CUE_SW
REV_SW
KEY2_B
V+6R6
GNDD
NM means STANDBY
RS1/10SR***J
CKSRYB 51048-0700
JH1201 V+6R6
V+6R6 1
*CAPACITORS
GNDD
220
220
2
Indicated in Capacity/Voltage(V)
unless otherwise noted. u F , p pF CUE_LED 3
*RESISTORS CUE_SW 4
R1217
R1216
B Indicated in , 5% tolerance
unless otherwise noted. k k , M M . PLAY_LED 5
PLAY_SW 6
KEY2_B 7
GNDD
PLAY_LED
PLAY_SW
CUE_LED
CUE_SW
KEY2_B
V+6R6
GNDD
C I KSW2 ASSY (DWS1426) CN1401
52147-0710
7
V+6R6
V+6R6
220
220
D1404 D1402
CUE LED
R1401
(AMBER)
GNDD R1413
R1412
680
Vf=2.2V If=3.2mA W=7.1mW SLI-343Y8C(KLMN)
Q1401
LTC124EUB
S1401
CUE
D DSG1117-A
C1401
D1403 D1401 NM
PLAY LED
R1403
(GREEN)
220 S1402
Vf=2.2V If=10.0mA W=22.0mW SLI-343M8C(FGHJ)
R1404
Q1402 PLAY
NM LTC124EUB DSG1117-A
C1402
NM
GNDD S1403
VSG1024-A
R1409
3.9k
E S1404
VSG1024-A
R1410
5.6k
S1405
VSG1024-A
R1411
10k
S1406
VSG1024-A
C1403
NM
F GNDD
H I
82 CDJ-850
1 2 3 4
5 6 7 8
G H JUMPER A
USB_ACT_LED
USB_STOP
8KEY_LED
4KEY_LED
2KEY_LED
1KEY_LED
SHIFT_SW
PLAY_SW
8KEY_SW
4KEY_SW
2KEY_SW
1KEY_SW
REV_LED
REV_SW
KEY2_B
H KSW1 ASSY (DWS1422)

220
220
220
220
220
220
220
USB LED
R1217
R1216
R1215
R1214
R1213
R1212
R1211
(RED) B
V+6R6
R1201
D1201 1.5k
SLI-343U8RC(HJKL)
Q1201
LTC124EUB
S1201
S1207
1
DSG1079-A
VSG1024-A
C1201
NM C1207 C
S1202
NM
2
DSG1079-A GNDD
C1202
NM
S1203
V+6R6
4 SLI-343Y8C(KLMN)
DSG1079-A
R1204
Q1202 1KEY LED
C1203
1KEY_LED LTC124EUB
D1203 2.7k (AMBER)
NM
S1204
D
8 SLI-343Y8C(KLMN)
DSG1079-A Q1203 R1206 2KEY LED
C1206 LTC124EUB
2KEY_LED D1204 2.7k (AMBER)
NM Vf=2.2V If=1.6mA W=7.2mW
S1205
SLI-343Y8C(KLMN) 4KEY LED

B_SHIFT Q1204 R1208
(AMBER)
DSG1079-A
LTC124EUB Vf=2.2V If=1.6mA W=7.2mW
4KEY_LED D1205 2.7k
C1204
NM
8KEY LED
S1206 SLI-343Y8C(KLMN)
R1210 (AMBER)
Q1205
REV Vf=2.2V If=1.6mA W=7.2mW
8KEY_LED LTC124EUB 2.7k
DSG1079-A D1206 E
C1205
NM REV LED
SLI-343U8RC(HJKL)
Q1206 (RED)
GNDD LTC124EUB
R1203
REV_LED D1207 D1202 1.5k
GNDD
H
CDJ-850 83
5 6 7 8
1 2 3 4
10.10 JFLB and JOGB ASSYS
A FL HOLDER DNF1735-
V1801 DEL1058-A
JOG FL
DAGND
PGND
LGND
VFDP2R7_F1
VDD
CLK
LAT
VH
Q1
Q2
1G
2G
BK
F2
F1
SI
VFDP2R7_
1
10
11
12
13
23
24
25
30
38
26
27
28
29
V+27 Q1803 R18
4 2SB1237X(QR)
3.3
C18
2 100u/
UDZS6R8(B)
3
D1801
C1812
R1813
100k
10u/50
ZL
V+3R3_SW
R1805
1
R1801
10
10
B
C1832
NM
Q1801 NM
C1807
C1806
2SC1815(GR)
HAR
NM
R1843
100k
100k
R1802
R1803
R1806
R1807
0.1u
68k
68k GNDD
Q1802 10k
V+27
2SC1815(GR) R1841
R1810 R1814
R1804
R1808
NM
33k
33k
10 10
R1845 R1811 R1815
C1813
10k
0.1u
NM NM
R1844 R1812 R1816
NM NM
GNDD
GNDD
C1808
C V+3R3_SW 47p CH
JH1801 C1809
100p CH
51048-0400 C1810
100p CH
GNDD 4 C1811
100p CH
V+3R3_SW 3
JOG1 2 GNDD
JOG2 1
NM HAR
C1801
R1857
NM
RB160M-60
RB160M-60
V+12
D1802
D1803
CTF1579
GNDD L1801
C1814
D V+27SW
CN1801
CCG1255
1.0u/50
C1816
C1817
C1818
10u/50
1.0u/50
CKS1072-A CCG1255
SHEET SW
JOG_SW 1
C1802
0.022u
NC 2
GNDD 3
V+12 V+38 V+3R3_SW
GNDD
C1804
C1803
47u/16
0.1u
E GNDD
V+12 13
GNDD 12
V+38 11
GNDD 10
9
CN1802
JOG1
JOG2
JOG_SW
J_DSO
J_BK
J_SCLK
J_LAT
GNDD
V+3R3_SW
VKN1244-A
*CAPACITORS
*RESISTORS
G CN1002 CN
unless otherwise noted. k k , M M . 52151
J
F V+3R3
: Waveform Measuring Point G
Therefore, when replacing, be sure to use parts : Voltage Measuring Point
J of identical designation.
84 CDJ-850
1 2 3 4
5 6 7 8
A
J JFLB ASSY (DWX3154)
27V DCDC CONVERTER
V+27
V+27SW
F2
VFDP2R7_F2 V+12 V+3R3_SW V+27 V+38 V+12

L1802 D1809
38
803 R1842
DTL1187-A RB160-60
2.2k SA2.2k SA
Q1808 2.2k SA2.2k SA
2.2k SA2.2k SA
QR) R1828 R1832
1k SA 1k SA
1k SA
R1855
R1820
R1849 R1848
R1850
R1852
R1846
NM
3.3k IC1803
0 SA
R1837
SA SA 22
R1823
C1815 270 270
43k
8 1
D
R1824
UDZS10(B)
100u/10 CD CS
SA
UDZS6R8(B)
R1829
1k SA
7 2
D1804
R1818
R1821
R1851
R1853
2SD1767(QR) R1847
10k
SI ES
0.51 180 SQ 6 3 C1829
C1830
C1831
V+ CT
22u/50
NM
ZL
R1838
R1819 5 4 330p
R1825 R1830
2.2k
2SD1767(QR)
Q1805
D
R1856 IN+ GND B
CH
ZL
330 SA 180 SQ
4.7k 4.7k NJM2374AD
C1824
C1825
NM
22u/50
Q1804
R1817
R1854
R1839
NM
!
2.2k
4.7k
D
LTC124EUB
V+27
Q1806
814 LTC124EUB
10 GNDD
815
GNDD
NM VFDP2R7_F1
816
NM
V+12
VFDP2R7_F2
P1801
NM R1822 5 C
24
1 SP 6 4 25
10k SA
R1840
RB160-60
R1833
C1828
22k
SQ
C1826
C1820
220u/25
D1806
220p
CH
ZL
0.1u
7 3
8 2
9 1
D1808 DTT1232-A
RB160-60 T1801
GNDD D
R1826
RB160M-60
G Q1807
RHP020N06 2.7V DCAC INVERTER
V+38 1k
D1803
SQ
CTF1579-A S
L1801 23 D1805 R1827 R1831
NOTES
RB160-60 100 22k
D
ACG1147-A
SQ
ACG1147-A
GNDD NM means STANDBY

CCG1255
4.7u/50
C1816
C1817
C1818
C1819
10u/50
4.7u/50
1.0u/50
! RS1/10SR***J
RS1/10SR****D
D
C1823
R1834
IC1802
0.1u
1.2k
D
RST1/2SP***J
1 8
SP
GND VDD RS1/8SQ***J
2 7 SQ
R1835
GNDD TRIG
16k
DISCH
D
GNDD 3 6 RS1/4SA***J
OUT THRES SA
4 5 CKSRYB
RESET CONT
1SS355
R1836
D1807
C1821
68K
D
CCSRCH
CH
100p CH TLC555IP
+
CEHAR
C1827
C1822
0.1u
+
CEHAZL
NM ZL
GNDD E
GNDD
K JOGB ASSY (DWX3155)

V+3R3_SW
PC1901
CN1901
C1901
R1903
SEDS-7573
0.01u
150
52151-0410 2
VCC
R1901
100 1
A VLED 5
JOG2 1
3 6
B
C1902
JOG1 2
0.01u
R1902 4 GND1
100 GND F
V+3R3_SW 3
int GNDD 4
Vf=1.52V If=11.8mA(typ If=16mA)
GNDD
J K
CDJ-850 85
5 6 7 8
1 2 3 4
10.11 SLD1, PSWB and SLD2 ASSYS
A
V+6R6 V+3R3_EUP L SLD1 ASSY (DWS1423)
EUP_LED
L1302
EJECT_LED
CTF1334-A
TCH/REL
JUMPER
GNDD
KEY0
L1303
VINYL_LED
CTF1334-A
V+6R6
L1304
MT_LED
G L
CTF1334-A
V+3R3_EUP V+3R3_EUP
B
ADCT
L1301
ADIN
NM
GNDA
3
PWR_SW
VR1301
2
DCS1062-A
1
R1301
0
TOUCH/RELEASE
D1305
C1305
NM
NM
GNDD GNDA
C1304
NM
C
GNDA
3
JH1301
JH1302
V+3R3_EUP
GNDA
ADIN
ADCT
PWR_SW
GNDD
GNDD
51048-0400
51048-0300
(JP1302:D20PDY0310E)
(JP1301:D20PDY0410E)
M PSWB ASSY (DWS1424)

D
ASG1102-A
S1601 RT1
N SLD2 ASSY (DWS14
6 3
5 ADCT 1
2
ADIN 2
R1503
4 1 D1501
NM
GNDA 3
V+3R3_EUP 4
RT2
E
CN1501
52147-0410
R1504
NM
R1601
220
GNDD
D1502
2
3
PWR_SW 1
CN1601
GNDD
GNDD
52147-0310
L M N
86 CDJ-850
1 2 3 4
5 6 7 8
A
)
SLI-343U8RC(HJKL)
R1307 EUP-LED
(RED)
D1301 1k
C1307
R1306
0.01u
NM
V+6R6
GNDD
D1304
R1309
680 EJECT-LED
SLI-343M8C(FGHJ)
R1310 (GREEN)
V+3R3_EUP Vf=2.2V If=12.9mA W=28.5mW
S1301 Q1302
680 B
R1319 LTC124EUB
L1301 EJECT-SW
NM 100 VSG1024-A GNDD
R1302
VINYL-LED
3.3k
VR1301 (BLUE)
R1314
R1315
R1311
DCS1062-A
220k
S1302
330
100
VINYL-SW
TOUCH/RELEASE VSG1024-A
R1303
Q1304 Q1305
3.9k
2SA1576A(QR) 2SA1576A(QR)
R1313
R1317
3.6k
0
R1304
C
5.6k
S1303 R1316
Q1303 D1302
A LTC124EUB
0 SLR343BC4T(JKLM)
TEMPO-SW
VSG1024-A R1318
R1305
0
10k
S1304
MT-SW GNDD
VSG1024-A
D1303
R1312 MT-LED
NM
C1306 2.4k (RED)
SLI-343U8RC(HJKL) Vf=2.2V If=1.8mA W=8.1mW
Q1301
LTC124EUB
D
GNDD
GNDD
SY (DWS1427) V+3R3_EUP
V+3R3_EUP
1SS352
1SS352
*CAPACITORS
R1503
D1501
D1503
NM
ADCT unless otherwise noted. u F , p pF
*RESISTORS
TEMPO SLIDER Indicated in , 5% tolerance E
unless otherwise noted. k k , M M .
3.3V
R1504
ADIN
NM
NOTES
1
DCV1009-A
VR1501
NM means STANDBY
2
RS1/10SR***J
CKSRYB
3
+
50K
CEJQ
C1501
C1502
C1503
1SS352
1SS352
0.1u/16
0.1u/16
47u/16
D1502
D1504
0V
GNDA
GNDA
L N
CDJ-850 87
5 6 7 8
1 2 3 4
10.12 POWER SUPPLY and ACIN ASSYS
A
P ACIN ASSY
(DWX3173: CUXJ)
(DWX3158: OTHERS)
! !
!
LIVE
1
1 LIVE (PURPLE)
1
2 NEUTRAL (BLUE)
NEUTRAL
JP2401
DKP3870-A
B AC POWER CORD
JA2401 PRIMARY L=120mm
DKP3891: CUXJ
DKP3889: OTHERS
CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE WITH

SAME TYPE NO. SST, 3.15A 250V MFD. BY NIPPON SEISEN CABLE LTD. FOR F1.
C SCK15057M
CN1 F1 TH2
T3.15AL 250V
3
C2
B72210-S2301-K101
220p RC1
D3SBA60
L1 L2 SFPL-52
C1 FB2 FB1 R114
NR1 R5 0.22 10 D101
1M C4
C3 0.1
220p C
TH1 C101
SCK15057M 0.0022
1
NR2 EXT41641-687C
B2P3-VH-LF T1 A
4
D C5 R15
C9 470k RC101
0.001 6 FME-220A C102
330/25V
R16 69
470k /25V
B
D10
D4
SARS04
MTZJ24B
FMV13N60ES
BAS21-03W Q4
R9
R7 47 D8 10 C10
R18 47p
10k
KTA1666 Q1
R10 R14 D9
100k 47 EG01C
R3 R4 R8
E 47
56k 10k SSC6210A
OUT
D2 L3
UDZS20B VH 7 D7 1
5
D1 1 Vcc
FM
4 Z2 R11 BAS21-03W
BAS21-03W VFB IS 100
23 8 2
GND
PRF18BB471QB2RB
PC1 4
TH3 C7 C8 R12 D11 C11

C6 RX1 0.33
0.01 0.001 0.001 22
3 5W /5V
MTZJ30B
PS2571-1
F
0.0022
C14
O P
88 CDJ-850
1 2 3 4
5 6 7 8
The > mark found on some component parts indicates

the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
! O POWER SUPPLY ASSY (DWR1463)
R114 SFPL-52
10 D101
B6B-XH-A-LF
C101
0.0022 C107 CN2
0.01
FBR07VA121 6 +12V STANDBY
L102 UPA2700GR
Q103 R110
5 +12V SWITCHED-MAIN
0.033
C106
1 D
0.1
RC101 R102 RX101 4 +12V SWITCHED-MAIN

PC1 R109
FME-220A C102 1k PS2571-1 R105
69 C103 1k 10k
/25V 69 L101 R111
2 D102 1k
/25V
UDZS5.1B
R106
R103
3.3k
C104
0.22
R104
11k
2.2k TCB-064
Q102 E 1/2
R108
100k KTC3875 R113
CN2001
10k
Z101 3 STANDBY-CONTROL IN
R112
4.7k
R107 RX102
820 Q101 2 GDD
KRC122S D103
L103 E
UDZS15B
1 GNDD
FBR07VA121
O
CDJ-850 89
5 6 7 8
1 2 3 4
10.13 VOLTAGES
A
E CMPX ASSY
Point to be Possible defective point STANDBY (At
Name Normal voltage level
checked when a voltage error is generated POWER SW is OFF)
1 V+12_EUP 11.4 to 12.6 V POWER SUPPLY ASSY, IC1001 ON
POWER SUPPLY ASSY,

2 V+12 11.4 to 12.6 V MAIN ASSY, CMPX ASSY, OFF
DFLB ASSY, JFLB ASSY
3 V+7R6 7.22 to 7.98 V IC2001, R2003-R2006 OFF
B 4 V-11 -9.9 to -12.1 V IC2001, R2003-R2006 OFF
5 V+10_A 9.5 to 10.5 V Q2028, D2017, IC303 OFF
6 V-10_A -9.5 to -10.5 V Q2031, D2018, IC303 OFF
7 V+5_USB 4.95 to 5.05 V IC2002 OFF
D MAIN ASSY
C
8 V+5R6 5.53 to 5.87 V IC409 OFF
9 V+3R3 3.2 to 3.4 V IC401 OFF
10 V+1R2 1.19 to 1.21 V IC404, R426, R427 OFF
11 V+3R3_A 3.27 to 3.33 V IC402, IC302, IC301 OFF
12 V+1R25 1.24 to 1.26 V IC403, R421, R422 OFF
13 V+5R6_M 5.54 to 5.66 V IC206 OFF
14 V+3R3_S 3.27 to 3.33 V IC408 OFF

D 15 VREF1R65 1.57 to 1.73 V IC201, IC408 OFF
16 V+5_A 4.95 to 5.05 V IC406 OFF
17 V-AUDIO (V-10_A) -9.5 to -10.5 V Q2031, D2018, IC303 OFF
G DFLB ASSY
18 V+3R3_EUP 3.27 to 3.33 V IC1001, IC1007 ON
E 19 V+3R3_SW 3.27 to 3.33 V Q1018, V1001, V1801 OFF
20 V+6R6 6.53 to 6.67 V IC1006, V1001, LED OFF
21 F+ 2.4 to 2.6 V V1001, R1142, R1144, Q1022 OFF
J JFLB ASSY
22 V+27 25.7 to 28.4 V IC1803, R1837-1839 OFF
23 V+38 34.2 to 41.8 V D1802, D1803, V1001 OFF

F
24 VFDP2R7_F1 AC2.7 V, DC7.1 to 7.8 V IC1802, Q1807, T1801, D1801, Q1803 OFF
25 VFDP2R7_F2 7.1 to 7.8 V D1801, Q1803 OFF
90 CDJ-850
1 2 3 4
5 6 7 8
10.14 WAVEFORMS
A
NOTE: The following waveforms were measured at the point of the corresponding
D MAIN ASSY balloon number in the schematic diagram and PCB diagram.
IC103 - pin 50 (CLK_66M) IC103 - pin 126 (SRVSCLK) IC103 - pin 135 (LPS1) IC201 - pin 28 (AGCRF_TP)
1 V: 1.0 V/div. H: 20 nS/div.
6 V: 1.0 V/div. H: 200 nS/div.
11 -1
V: 1.0 V/div. H: 1 S/div. DISC IN
14 V: 500 mV/div. H: 500 nS/div.
IC301-pin 45/DSP16M_TP (CLK_A_16M) Foot of R162 (PNL_XBUSY) IC103 - pin 135 (LPS1)
2 V: 1.0 V/div. H: 100 nS/div.
7 V: 1.0 V/div. H: 200 μS/div.
11 -2
V: 1.0 V/div. H: 1 S/div. DISC EJECT
IC201 - pin 73 (CLK_S_16M) Foot of R191 (TSCK) IC103 - pin 134 (LPS2) C
3 V: 1.0 V/div. H: 100 nS/div.
8 V: 1.0 V/div. H: 200 μS/div.
12 -1
V: 1.0 V/div. H: 1 S/div. DISC IN
IC103 - pin 85 /SH_STATUS_TP(SH_STATUS) Foot of R163 (TSI) IC103 - pin 134 (LPS2)
4 V: 1.0 V/div. H: 500 mS/div.
9 V: 1.0 V/div. H: 200 μS/div.
12 -2
V: 1.0 V/div. H: 1 S/div. DISC EJECT
D
IC103 - pin 72 (DSPDREQ) Foot of R193 (TSO) IC201 - pin 37 (RFO_TP)

5 V: 1.0 V/div. H: 20 μS/div.
10 V: 1.0 V/div. H: 200 μS/div.
13 V: 500 mV/div. H: 500 nS/div.
CDJ-850 91
5 6 7 8
1 2 3 4
A
G DFLB ASSY balloon number in the schematic diagram and PCB diagram.
V1001 - pin 31 (D_SCLK) V1001 - pin 32 (D_LAT) CN1002 - pin 5 (JOG1)
1 V: 1.0 V/div. H: 50 μS/div.
3 V: 1.0 V/div. H: 50 μS/div.
5 V: 1.0 V/div. H: 10 mS/div. JOG scratch
V1001 - pin 33 (D_BK) V1001 - pin 30 (D_DSO) CN1002 - pin 6 (JOG2)

2 V: 1.0 V/div. H: 50 μS/div.
4 V: 1.0 V/div. H: 50 μS/div.
6 V: 1.0 V/div. H: 10 mS/div. JOG scratch
J JFLB ASSY balloon number in the schematic diagram and PCB diagram.
V1801 - pin 27 (J_SCLK) V1801 - pin 25 (J_BK) V1801 - pin 26 (J_LAT) V1801 - pin 24 (J_DSO)
1 V: 1.0 V/div. H: 200 μS/div.
2 V: 1.0 V/div. H: 200 μS/div.
3 V: 1.0 V/div. H: 200 μS/div.
4 V: 1.0 V/div. H: 200 μS/div.
92 CDJ-850
1 2 3 4
5 6 7 8
10.15 EACH SIGNAL LEVEL
A
G DFLB ASSY
Point to be checked Signal Name Signal Level
H (3.3 V): Switch OFF
A PWR_SW
L (0 V): Switch ON
H (3.3 V): Power ON
B PWR_ON
L (0 V): Power OFF
PLAY/CUE/AUTO BEAT
LOOP 1-4/BEAT SELECT/ H (3.3 V): When the buttons are not pressed
REV/LOOP IN/OUT/RELOOP/ L (0 V): When the buttons are pressed
USB STOP/RENC_SW
B
C ADCT 1.65 V
D ADIN 3.3 V to 0 V: TEMPO slider + side to - side
E 3.3 V to 0 V: Turn it from clockwise direction to

TCH/REL
counterclockwise direction
H (3.3 V): When does not touch the JOG
F JOG_SW
L (0 V): When touch the JOG
H (3.3 V): Release PANEL CPU reset
G RESET(PNL_XRST)
L (0 V): PANEL CPU reset
C
E CMPX ASSY
H (12 V): Audio mute
H AMUTE
L (0 V): Release audio mute
H (3.3 V): Release audio mute
I MAIN_XMUTE
L (0 V): Audio mute
H (3.3 V): Power OFF
J PWR_XON
L (0 V): Power ON
D MAIN ASSY D

H (3.3 V): USB VBUS ON
K USB_VBUSON
L (0 V): USB VBUS OFF
H (3.3 V): Normal
L USB_CDETFLG L (0 V): Overcurrent detection
H (3.3 V): USBA
M USB_ABSEL L (0 V): USBB
H (5 V): External PC connection (at PC mode)
N VBUS
L (0 V): External PC no connection (at PC mode)
H (3.3 V): Pickup position is except for the most internal
O INSW(INSIDE) E
circumference.
L (0 V): Pickup position is in the most internal circumference.
H (3.3 V): Release MAIN CPU reset
P MAIN_XRST
L (0 V): MAIN CPU reset
H (3.3 V): Release AUDIO DSP reset
Q DSPRST
L (0 V): AUDIO DSP reset
H (3.3 V): Release SERVO DSP reset
R SRVRST
L (0 V): SERVO DSP reset
H (3.3 V): After the disc insertion
S DRVMUTE1, 2
L (0 V): The disc non-insertion
1.65 V: In normal (At the acceleration of the start-up is
T SPIN
around 3V.) F
CDJ-850 93
5 6 7 8
1 2 3 4
11. PCB CONNECTION DIAGRAM

11.1 CNCT, SLMB and JINT ASSYS
A
SIDE A
NOTE FOR PCB DIAGRAMS :

1. The parts mounted on this PCB include all
necessary parts for several destinations.
For further information for respective desti-
nations, be sure to check with the sche-
matic diagram.
2. View point of PCB diagrams. CN1701

CONTACT
Connector Capacitor
1
B
SIDE A
SIDE B
P.C.Board Chip Part
STEPPING
MOTOR
CN2304
C JINT ASSY
1 1 4
C CN2304
SPINDLE 5
ST1+
ST2+
ST1-
ST2-
14.VR780PD
CONTACT
MOTOR 19.LD780 SIDE-UP
20.GNDS
18.GNDS
17.GNDS
16.GNDS
15.GNDS
13.GNDS
12.GNDS
24.FR
23.FD
22.TR
21.TD
11.A
10.B
CN2301
LF [[ G ]]
9.GNDS
8.GNDS
1.GNDS
4.VRFE
2.V+5P
CONTACT
SIDE-DOWN
A30C5/C7
7.C
6.D
5.E
3.F
CN2301
1.INSW
12.VCC
7.W+
5.HB
1
9.V+
6.W-
11.U+
2.W
8.V-
10.U-
4.U
3.V
12 10 5 1 CONTACT
C2302 SIDE-DOWN
C2303
Production Code CN2302

C2307 24
20 15 10 5 1
1
C2304
C2305
R2302
R2303
CN2302
A CNCT ASSY CN2502
18.GNDS 10.B 1.GNDS CONTACT SHORT SW

19.LD780 11.A 2.V+5P SIDE-DOWN SHORT OPEN
20.GNDS 12.GNDS 3.F CN2502
13.GNDS 4.VREF S2501
14.VR780PD 5.E 24 1
21.TD
[[ G
20 15 10 5 1
E 15.GNDS 6.D CN2501
22.TR 7.C CONTACT
L2502
16.GNDS C2503
L2501
23.FD 8.GNDS SIDE-DOWN A30C

C2505
C2506
C2508
24.FR 17.GNDS 9.GNDS 1

19.D
C2501
C2507
C2504
1.FR 20.E
21.VCC
C2502
1 1 5 10
CNCT
2.FD
3.TR
8.PD 14.A
9.LD780 15.B 22.VREF
15 20
24 DWX3151-
4.TD 10.GNDS 16.VRF 23.F
5.NC 11.VR780 17.SW1_ 24.GNDS
6.GNDS
7.LD650
12.VRCOM
13.VR650 18.C
DVD/CD
LF
CN2501 (DNP2602-C
09SD PICKUP ASSY
A B C
94 CDJ-850
1 2 3 4
5 6 7 8
A
SIDE A
LOADING
MOTOR ASSY-S
B SLMB ASSY
Production Code
W
SLOTS
CN1701 1.LPS2
2.LPS1 1
CONTACT SIDE UP 3.GNDD S1701
1 5 4.LO+ S1702
5.LO-
SLOTSW B
1 5
SLMB
1
DWS1425- /J
CN1701
(DNP2601-C)
EPPING
OTOR
CN2304
CN2303
D CN201
1 4 CONTACT
CN2304 C
5 1 SIDE CN2305
ST1+
ST2+
ST1-
ST2-
CONTACT
SIDE-UP 5 1 CN2303
DWX3157- /J CN2305
3.GNDS
2.LPS1
1.LPS2
C2301
4.LO+
5.LO-
1.GNDS
JINT
4.VRFE
2.V+5P
CONTACT
C
6.D
5.E
SIDE-DOWN
3.F
50 45 40 35 30 25 20 15 10 5 1
1 50
1.INSW
C2306
TACT
2.W
E-DOWN
8.GNDD
22.LD780
16.GNDD
21.GNDS
23.GNDS
33.GNDS
34.GNDS
35.GNDS
30.VREF
15.V+5M
32.V+5P
29.A_S1
31.A_S1
36.LPS1
2
10.HW+
9.HW-
14.HU+
12.HV+
27.A_C
28.A_D
25.A_A
26.A_B
13.HU-
11.HV-
24.PD
17.FR
18.FD
19.TR
20.TD
3.W
6.U
7.U
4.V
5.V
38.GNDS
37.LPS2
43.ST2+
44.ST2+
47.ST1+
48.ST1+
45.ST2-
46.ST2-
49.ST1-
50.ST1-
41.LO+
42.LO+
39.LO-
40.LO-
(DNP2602-C)
The pin No. indications (1 and 50) near the CN2305 connector and the pin
numbers adjacent to the signal names are printed in reverse on the board.
On the board, the leftmost pin is labeled Pin No. 1 and the rightmost Pin No. O.
However, the actual pin numbering is Pin No. 1 at rightmost and Pin No. O at
SHORT SW leftmost.
SHORT OPEN Note that only the printing of the pin numbers is wrong but that that of the signal
S2501 names is correct. When performing diagnosis, be sure to interpret the pin numbers
[[ G ]] of the connector in reverse (enumerated right to left). E
A30C5/C7
C2508
1
C2501
C2507
C2504
CNCT
DWX3151- /J
LF
(DNP2602-C)
A B C
CDJ-850 95
5 6 7 8
1 2 3 4
SIDE B
A
B SLMB ASSY
DWS1425- /J
SLMB WHITE GRAY CN1701
[[ G ]] LF LO+ LO- 1.LPS2
2.LPS1
C7 3.GNDD
4.LO+
SLOTSW
5.LO-
5 1
SLOTSW
B
ADD SOLDER
CN1701
(DNP2601-C)
CN2303
C JINT ASSY CN2305

C
LO+ LO-
GNDS V+5M
GNDF GNDD
A CNCT ASS
780
E
A B C
96 CDJ-850
1 2 3 4
5 6 7 8
SIDE B
A
CN1701
1.LPS2
2.LPS1
3.GNDD
4.LO+
5.LO-
1
B
N1701
CN2304
N2303
CN2301
O+ LO-
HB VCC
CN2302 (DNP2602-C) D
A CNCT ASSY CN2502
V+5P VREF
FD TD
LD780 VRF
E
GNDS
FR TR
CN2501 (DNP2602-C)
A B C
CDJ-850 97
5 6 7 8
1 2 3 4
11.2 MAIN ASSY

SIDE A
A
E CN2004
D MAIN ASSY CN401 8 M 9 Q L 5
[[ G ]] GNDD V+3R3
A30C5 9 5 10
1
C256
R405 R406 IC205 2 3 7 1
C463
10 5 1
B KN401 13 1 1
1
CN401 4 5 6 8 C128 C131 IC103
C426
C111
R266
180
C429 C434 C402 180 175 170 165 160 155 150 145
V5R6
C473
R483
D304 R344
D303
R470
R508 C435
IC401
C403
C112
C502
C448
R147 C431
R115 C113
C124
185
D101 C471
190
C114
R340
C406
R148 R185
11
195
R604 C494
1 C125
R186
200
CN2006
C116
C117
PC
CONTACT SIDE UP
5
C115
205
CN403
CN403
210
FC
C333
C334
C331
R110 R111 R112 R113 C121

1
1
10
F401
215
E
DSP16M
220
C341
R422
15
225
IC403 F302 C126
1
1
C119
17
230
R316 C118
17
R339 R315
V-AUDIO
235
R354 C451
R336 R313
CONTACT SIDE UP
C322
C323
240
C340
C120
240
1 5 10 15 20 25 30 35
1
CN402
1 R116
1
F301
R117
R421 C409
C335
R345 C467
R128
C411
C407
R304
R120
R302 C139
R310
C336
5
16 C127 C130
C129 1 1 1 1
R129
R130
ARO C318 C188
CN2002
R135 R13
R132
D C482 C320 C314 R187
1 R134
R473 V+5_A C138
10
ALO
AOI
C193 C134 C196 C137

CN402
R477
C315
C132 C133
C487 12 2 F102
C342
C450 8
C186
C123
1
15
C472
C470
C453
C178
E
R507 11
C447 R428
C316
R496 C110
C405
R504 R179
IC410 R482 IC411
20
C145
14
7
1
10
5
R498
1
10
5
25
14
R505
1
R503
7
R471
C446 R430 R506

R434
R446
27
Q405 R499
KN402 R431 R448 R419
C458
R453
1
KN403
C504
R429 R418
E Q408
1
R441
R443
R440
1 1
A C452 R420 R417
IC410 IC411 IC403 IC401 IC205 IC103

Q405 Q408
D
98 CDJ-850
1 2 3 4
5 6 7 8
SIDE A
A
NOTE: The encircled numbers denote measuring point.
Q L 5 K 11 12 6 N 15 10 T S S
DWX3174- /J MAIN
R295
C180 R169
C170 C194 14 IC105
10
C152
C159
IC404
C455 R297
C146 C150 C171 C153
R274
C160
C161 B
R150
R157 R151
C128 C131
R427
IC103 C144
X103
R296 C252
C156
DAVMUTE1
165 160 155 150 145 140 135 130 125 1 DAVMUTE2
R158
SPIN
1 5 C410
120 120
7 C456
R269
C479
C408 1
C247 C270
C157
R426 R268
C480
R173
SPDLFG
C495
R265
1
R256
115
C109
C122
R172
C412
F101
C177
110
L401
R267 C255
EC W
C158
C173 C241 V
105
1 R252 U C283
100
C167
C169
C269
V+5R6M
X102
95
R255
C459
C162
C281 C265
C246
90
VCA RFRP C268

R165
1 R164 R294
FOO
FE 13
C
85
C274
C277
C154
C278
C266
C267
C271
TE
C163
TRO
SH_STATUS R293
80
C182
C155
C240
C165
C164
SBAD ST2+ ST1+

C233
R249
75
C234 ST2- ST1-

IC201
70
75 LD3S
LDCHK
FTE
C235
C238
C232
75 70 65 60 55
R511 L229
R244
65
50
R243 R246 C230

50
C221 R245 L228

C231
L227
L204
L203
L202
L201
80
C218
45
R242
5 20 25 30 35 40 45 50 55 60 RFO
60 13
85
5
40
R184
1
C168
1
C139 1
90
R178 C149
CN201
35
C460
R143
5
R170
C225
95
30
C148
1 1 1 1 1 R138
10
X101 C279
100100
R135 R136
R132
R134 TX
CN2305
C138 C143 C217 A-S2 D
15
C137 C142 V+3R3B RX 1 5 10 15 20 25 C215

25 A-S1
C275
CN201
20
GNDD
C211 AGCRF A-D

R109
IC104
A-C
SBOK
C186
C123
C276
IO0B
IO1B IO2B
1
25
R154 R166
R171
C201
IPF
C280
R201
C
30
R276 A-B
IO3B
C151
C179
C166
C110
R179 R177 R240 R241 C212 R292 A-A

CONTACT SIDE UP
C206
C207
C208
C261
35
C145 C222 C223 C202

C260
40
C204 GNDS
1 7 10 9 P R 4 14 3 14
45
B
50 50
1
KN404
E
(DNP2600-C)
O
IC103 IC105 IC404

IC104 IC201
D
CDJ-850 99
5 6 7 8
1 2 3 4
SIDE B
A
D MAIN ASSY
C264
C272
DWX3174- /J MAIN
C263
1
IC206
R273
R271
R272
C258
C253
LF
R198
B
C250
27
R270
R288
R289
C257 R287
R141
IC204
R140
R131
R197
30
25
R247 R248 R250

R264 R167
C135
C262 C248 C273

C245
C141
R155
R258
35
20
C140
C195
R515
Q107
R196
R251
C242 C243
R257 R259
C136
D103
R260 R175
R263
C254
R514
40
15
R261
R156
C457 R133
C249
1
C244
R262 R254
C251
R253 C192
45
10
1 Q104
C197
R159
ADC
C107
1
C462 C419 R516
R160
IC405
50
C259 R413
E
IC102
R286 R409 Q109 27 25 20 15 0
IC408
R152
54
IC203
1
C108
C
C414 C421
R456
R161
R233
R232
C181
R228
1
R227
R454
R513
C237
C465
R192
C415
1
C418
C422
Q201
R199
C236 C400 R153
L226 R162
R512
C228
L224
C213 R234
C185 R149
C214
C209
30 35 40 5
L221
C147
C183
R163
L205
L206
R208
R209
C103
R190
R105
L220
R189
C239
R193
R291
C282
R144 R510
C227 R290 R275 R142
R191
L219
C184
1
C224 R238 KN102
AWRC R237 IC101
L216
R236 1
D C220 5
L217
L218
L207
C210
C205
R225
R231
R230
C219
L208 R235
L215 L222
R226 10
CN201
C176
L209 C216
L210 15
L211 R229
L212 R224
C203 20
L213
L214 C191
24
L223
L225
C478
C477
E
IC204 IC206 Q104 Q107

IC405 Q201 IC203 IC408 Q109 IC102
IC101
D
100 CDJ-850
1 2 3 4
5 6 7 8
SIDE B
A
CN401
E C433 R603
C476
C436
Q412
C441
C440
R123
R121
R119
C425
C430
R404
C428
C443 C437
R118
R124
R402 R403
R122
C442 C432 R337 R347 B

C337 R348
R464
IC409 R341 C338
R401
R182
R131
R197
R180
1
C135 R183 C445 R466
C496 C444
C140
R196
C136 R114 C189 Q101

R194
R195
R181
R469
R468
R467
R146
C461
C499
C497
C498
R133 R601
1 R145
C439 R137
C493 C492 R605

C438 R139
Q301
C427
Q302 Q102
R103
1 E
C424
C107
C106
C104
C105
D401
10 C174
L403 R338
CN403
5
IC102 IC107 R352 1

C313 R350
R320
1
R317
1
C312
25 20 15 10 5 1
R349 Q303
C311 R356
R108
C
40
C310
IC303
R333
C332
R342 R343
R353
R357
IC301
40
35
30
25
1
R358
C309 C339
20
C308
20
C305
R334
R332
45
R331 C329
15
R104
R329
R351
R328
C327
1
5
R314 C330 R330
50
30 35 40 45 50
R312
10
54
C325
R308
C328
R188
C103
C102
R324
R326
55
R105
C306
5
1
C304 R322
R510
C307
R325 IC302
C190
60
60
R142
R125
R101
R327 R323
C326
R346
R416 R415
R472 R474 R479

70
75
80
65
80 C466 C413
IC101 C301 C484
48
C489
F402
C302 R307 15 10 C324

1
45 16
R106 R102
C303 D
R303
1
R301
C101
1
R305
IC406
C404
1
40
CN402
C416
C486
C401
IC402 R481
35 1 5 8 C483
1
C319
C417 R480 L408

R107
30 C317 C468 C488

C490 C503
L407
1
R458
R461 R424
25 1 C449 R462 C420

C474
R497 R459 R460

C464
C343 C481
C321
R407
R486
R444
R432
R408
Q413
R492
R423
C475
C501
R476 C485
Q406
C187
Q414
R463
R437
R491
Q415 D402
C505
R485
C506
Q410
R602
R509
R484 R435 D403 E Q411 E E C423 C469

R436 E C454
R495 C507
R414
R494
R487 Q402 E
E R412
E R411
D404
E E
R501
D406 D405 R425 Q404 R410 R502
(DNP2600-C)
Q412 IC409 Q101

IC102 IC107 Q102
IC101 Q303 Q302 Q301
IC301 IC302 IC303
IC402 IC406
Q413 Q414 Q411 Q410
Q415 Q406 Q404 Q402
D
CDJ-850 101
5 6 7 8
1 2 3 4
11.3 CMPX and USBA ASSYS

SIDE A
A
E
4
3 5 11
Q2017
C2084
JA2003
Q2015 VA2001
Q2016 Q2016
Q2017 R2067
E
R2062 C2083
IC2001
R2060
Q2014
C2076
R2087
E
Q2015
E
B
Q2014
Q2029 Q2026 Q2030
C2101
R2039
IC2006
Q2027
C2069
C2061
R2049
R2042
R2051
Q2032 Q2031
R2040
Q2028 C2041
Q2018 R2094 1
Q2013
Q2012
Q2013
1
Q2012
IC2006 R2041
5
Q2019
C2063
C2075
R2037 1
5
5
CN2005
R2026 C2070
R2093
CN2005
C2053 R2029 C2064
R2048
C2102 Q2010 C2057
R204
R2089
Q2010 R2036
F2001
R2090
R205
1
1
R2045
11
R2032
R2025 R2050
1 C2062
R2047
R2034
C2051
R2028
C2059
5.GNDD
4.GNDD
Q2031 R2078 D2018
R2068 R2088 R2081 R2079

Q2030 C2094
C IC2005
F USBA ASSY 3.USBA_D_P
2.USBA_D_N
IC2005
C2096 C2091 L2015

Q2027 Q2026
C2052
R2030
1.V+5_USB 5
C2058
R2033
R2035
JA2201 C2060
[[ G ]] 1
Q2011 LF A30C5/C7 Q2011

R2038
17 R2092
17.GNDD C2054
4 1 1 1 16.GNDD
15.VBUS_B R2031
5
VA2201 14.GNDD
C2203 L2201
R2027
C2100
R2091
GND 13.USB_D_P
JH2201
D2021
5
C2204 12.USB_D_N 11.GNDD R2024

GND VA2202 10.CONT2 9.GNDD
D+ 8.CONT1
1 F2201 D2201 6.GNDD 7.GNDD R2098
16
D- 5.GNDA
R2085
15
4.LOUT F2003
3.GNDA
CONTACT SIDE 1
2.ROUT
1
1.GNDA
V+5
REPLACE IC LINKS AS MARKED.

JH2201
10
1
C2202 20.V+12_EUP 21.GNDD

C2201 19.GNDD
P2003 AND P2004 TYPE NO.

18.V+12
P2003 ET P2004 N'UTILISER

D 16.GNDD 17.V+12
REMPLACER LE IC LINK
15.VDET
5
MFD. BY Littelfuse Inc.
DE CHEZ Littelfuse Inc.

466.500 AND 466.375
QUE LA REFERENCE
14.PNL_XMUTE
A30C5/C7
13.PWR_ON
466.500 ET 466.375
R2086
COMME INDIQUE.
2
12.MAIN_XRST 11.USB_STOP
[[ G ]]
10.MAIN_ZBUSY
1
8.GNDD 9.PNL_XRST
ATTENTION -
6.GNDD 7.PNL_CNVSS CAUTION -
5.TSCK
CN2006
LF DWX3156- /J
4.GNDD
2.PNL_XBUSY
3.TSI
1.TSO
USBA
L2007
C2089
Q2033
27
C2033
1
IC2002
26
R2015
D2005
Q2033 27.USBA_D_P
25
R2099
26.USBA_D_N 25.GNDD
(DNP2602-C) R2018 5 24.USB_CODETFLG
1
22.USB_VBUSON 23.GNDD
20
Q2021 21.GNDD
20.PWR_ON
E
IC2003 IC2002 18.VDET 19.GNDD

Q2021
CN2002
17.GNDD
IC2003 16.MAIN_XMUTE 15.GNDD
15
1 14.MAIN_XRST 13.TSI
7
1 C2036
12.MAIN_XBUSY 11.TSO
20
21
10.PNL_XBUSY
466.375
P2004
E 9.GNDD
1
8.TSCK
10
6.V+5R6 7.GNDD
Q2034
4.GNDD 5.V+5R6
E
1
Q2034
CONTACT
R2084 3.GNDD
20
2 SIDE
CN1001
2.V+12_EUP 1.GNDD
5
C2097
CN2007
CN2003
C2098
15
CN2001
C2099
1
1
5
P2001
6
CONTACT SIDE
1.V+12_EUP
CN2003
10
V+12_
G
2.GNDD EUP
3.PNL_XRST
V+12
5
4.PNL_CNVSS
1
5
C2012
5.TSCK V+12
L2001
6.TSI PWR_
1
7.PNL_XBUSY XON
C2003
L2006 8.TSO GNDD

2
1
9.PWR_ON GNDM
1
F
CN2001
E F O CN2
102 CDJ-850
1 2 3 4
5 6 7 8
SIDE A
A
E CMPX ASSY H
R2058
D2014
2 C2077 JA2001
L2014
R2006 R2007
D2012 JA2002
R2076 D2017
C2092
R2077
R2055 R2063 C2074 A
R2056 R2064
R2097
R2096
C2013
C2017
R2008
L2016
C2019
R2001
C2022
R2080
R2083
D2011 Q2029 L2003 C2014
D2020 DWX3153
1
4 VA2003 - /J
1
5 11 5
C2084
C2021
JA2003
1
Q2015 VA2001
1 2
C2004
C2002
C2080 C2078
Q2016 R2065 C2079
1 1
VA2002
5 CMPX
E
C2083 C2081 R2057

A
C2001
C2006
R2100
R2087
E
C2073 R2003
C2093
5
1
E
466.500
1 R2005 R2004
1
B
Q2014
IC2001
F2002
C2005
R2053
E
R2054
C2095 P2003
IC2006
CN2004
1 1
C2069
R2049
C2090
D2001
E
R2051
C2010
C2087 1. V+7R6_M
10
E R2074 C2020 2. GNDM
R2073 L2017 3. GNDD
E 4. GNDD
C2011
R2071 C2009 5. GNDD
1
C2082 C2086 6. V+7R6_D

C2063
C2075
L2002
5
D2003
R2066 Q2018
D2004
13
7. V+7R6_D
C2070 R2061 8. GNDD
C2029
R2059 C2008 9. V+12
C2007
C2064 10. GNDD
R2048
R2095
C2015
D2002
R2002
Q2019 11. V-10_ A
R2069
D2019
Q2028
R2046
R2089
Q2032 12. GNDA
L2005
R2072
D2016
R2075
C2088
R2090
C2030
R2052 R2082 13. V+10_A
R2045 R2070
R2050
C2062
R2047
(DNP2602-C)
5 6 I 4 3 CN2004
Q2031 R2078 D2018
R2068 R2088 R2081 R2079

Q2030 C2094
C
C2096 C2091 L2015
Q2027 Q2026
D CN401
021
CN403
098
CN2006
REPLACE IC LINKS AS MARKED.
P2003 AND P2004 TYPE NO.
D
P2003 ET P2004 N'UTILISER
D
REMPLACER LE IC LINK
MFD. BY Littelfuse Inc.
DE CHEZ Littelfuse Inc.

466.500 AND 466.375
QUE LA REFERENCE
466.500 ET 466.375
COMME INDIQUE.
ATTENTION -
9
27.USBA_D_P
6.USBA_D_N 25.GNDD
4.USB_CODETFLG
22.USB_VBUSON 23.GNDD
0.PWR_ON 21.GNDD
8.VDET 19.GNDD
17.GNDD
6.MAIN_XMUTE 15.GNDD
4.MAIN_XRST 13.TSI
2.MAIN_XBUSY 11.TSO
0.PNL_XBUSY
8.TSCK 9.GNDD E
6.V+5R6 7.GNDD
CN402
4.GNDD 5.V+5R6
E
3.GNDD
CN2002
2.V+12_EUP 1.GNDD
CN2001
C2099
D
6
V+12_ 1
EUP
V+12 2
5
V+12
PWR_ J
XON
GNDD
GNDM
1
F
CN2001
CN2 E
CDJ-850 103
5 6 7 8
1 2 3 4
SIDE B
A
E CMPX ASSY
V+7R6M
1
GNDM
GNDD
GNDD
GNDD
V+7R6CDCD
B
V+7R6DCDC
GNDD
V+12
GNDD
V-10A
GNDA
13
V+10A
V+12_EUP
(DNP2602-C)
C
CN2004
PNL_CN
27.USBA_D_P
CN2006
25.GNDD 26.USBA_D_N
23.GNDD 24.USB_CODETF
D 21.GNDD 22.USB_VBUSO
20.PWR_ON
19.GNDD 18.VDET
17.GNDD 16.MAIN_XMU
15.GNDD 14.MAIN_XRST
13.TSI 12.MAIN_XBUS
11.TSO
9.GNDD 10.PNL_XBUSY
7.GNDD 8.TSCK
5.V+5R6 6.V+5R6
3.GNDD 4.GNDD
1.GNDD 2.V+12_EUP
USBA_D_P
GND
MAIN_XMUTE
CN2002
TS
E TSO
PNL_CNVSS
6
V+12_
V+12
V+12
CN2001
PWR_
GNDD
GNDM
1
E
104 CDJ-850
1 2 3 4
5 6 7 8
SIDE B
A
GNDA
5
CN2005
1
5.GNDD
4.GNDD C
3.USBA_D_P
2.USBA_D_N
1.V+5_USB F USBA ASSY
GNDF
17.GNDD
16.GNDD
15.VBUS_B
JH2201
14.GNDD
5
PNL_CNVSS 13.USB_D_P 12.USB_D_N
17
11.GNDD GNDD
10.CONT2 USBA_D_P
9.GNDD 8.CONT1
7.GNDD 6.GNDD USBA_D_N
5.GNDA 4.LOUT
1
3.GNDA 2.ROUT V+5_USB
USBA_D_P 1.GNDA
GNDD 26.USBA_D_N
GNDD 24.USB_CODETFLG 21.GNDD 20.V+12_EUP
GNDD 22.USB_VBUSON 19.GNDD 18.V+12 D
20.PWR_ON 17.V+12
GNDD 18.VDET 16.GNDD
15.VDET
USB_STOP
GNDD 16.MAIN_XMUTE 14.PNL_XMUTE

GNDD 14.MAIN_XRST 13.PWR_ON
1
TSI 12.MAIN_XRST
TSO 12.MAIN_XBUSY 11.USB_STOP 10.MAIN_ZBUSY
.GNDD 10.PNL_XBUSY 9.PNL_XRST 8.GNDD
.GNDD 8.TSCK 7.PNL_CNVSS
6.V+5R6
27
.V+5R6 6.GNDD
.GNDD 4.GNDD 4.GNDD
.GNDD 2.V+12_EUP 5.TSCK 2.PNL_XBUSY
3.TSI
USBA_D_P 1.TSO
GNDD USBA_D_N
USB_CODETFLG (DNP2602-C)
PWR_ON USB_VBUSON
MAIN_XMUTE
VDET
MAIN_XRST
V+12_EUP
TSI MAIN_XBUSY
TSO E
1
PNL_CNVSS V+5R6
21
V+12
V+12
CN2003
PNL_XRST
1
TSCK
PNL_XMUTE
6
V+12_EUP 1.V+12_EUP
V+12 2.GNDD PNL_XBUSY
3.PNL_XRST
9
V+12 4.PNL_CNVSS
5.TSCK
1
PWR_XON 6.TSI
GNDD 7.PNL_XBUSY
GNDM 8.TSO
1
9.PWR_ON
E F
CDJ-850 105
5 6 7 8
1 2 3 4
11.4 DFLB ASSY

SIDE A
A
G DFLB ASSY
J1095
J1052 J1079
D1013 D1014 INFO D
D1001
LINK
J1057
S1001
B
BROWSE TAG LIST S1009
J1032
S1007 S1008
J1041
V1001
D1002 J1082
USB
J1040
J1065
S1002
J1019
J1066
J1077
J1098
J1010
J1078
D1003
DISC
J1047
S1003
J1087
C
J1071
J1009
JUMPER
Production Code J1084

J1074
J1058
TIME J1088 J1033

G H
S1004 J1018
J1054
1 5 10 15 J1072
20 25
J1073
C1061
J1027
J1034
J1094
J1046
J1025
J1092
J1081 IC1006
J1051
D J1059
J1038
J1002 D1012
J1003
L1006
J1106
C1006
J1008
J1083
J1055
J1093
S1010
D1007
D1010
DFLB
J1086
RELOOP
DWX3152- /J
S1005 S1006
LOOP IN LOOP OUT
J1043
CONTACT SIDE
IC1006
E
J1064
J1069
J1060
1 1
CN2003
J1031
J1022
5
J1007
CN1001
CN1001
10
E
J1070
15
20
21
G
106 CDJ-850
1 2 3 4
5 6 7 8
SIDE A
A
J1020
J1049
INFO D1015 D1016
J1023
J1015
J1096
DL B
ST S1009 MENU
J1032 J1068 TAG TRACK
J1005
J1017
J1097
/REMOVE
S1012
V1001 S1011 BACK
S1015
J1082
J1011
J1026
J1062
J1089
J1044
J1001
J1019
J1016
J1056
C1016 ROTARY
1 SEARCH
J1053
J1039
J1087
JUMPER
S1018
C
J1085 J10485
J1050
X1001
G L
J1075 J1042
1033 J1099
J1012 J1102
J1104
1054
J1021
J1101
072
20 25 30 35 40
J1061
J1013
J1014
J1027
J1028 J1067
J1105
L1002
C1030
D
J1035 J1004
J1037
J1080
J1030 J1091
MEMORY
C1006
J1076
DELETE J1029
J1055
< CALL CALL >

J1045
J1090
J1100
S1017
S1013 S1014
J1103
J1036
S1016
152- /J J1006
J1063
CN1002 10
1 13
1 5
CONTACT SIDE UP E
CN1002 (DNP2601-D)
J CN1802
G
CDJ-850 107
5 6 7 8
F
E
B
A
D
C
108
G
SIDE B
1
1
18
1.V+12
3.V+38
2.GNDD
4.GNDD
9.J_BK
11.J_LAT
6.JOG2
5.JOG1
12.GNDD
8.J_DSO
10.J_SCLK
7.JOG_SW
13
13.V+3R3_SW
(DNP2601-D)
R1149 GNDA
R1148 R1106 C1046
R1147
/REMOVE
R1105 C1044
TAG TRACK
L1004 R1146 R1108
CONTACT SIDE
R1145
E
R1032 R1110
GNDD
R1104
ROTARY SEARCH
CN1002
Q1014
C1036
Q1014
1
V+12
V+38
2
2
UP
GNDD
L1012 C1040 R1183
5
G DFLB ASSY
GNDD
R1073 R1071
V+3R3_EUP
R1095 R1084 R1077
V+3R3_EUP
GNDD
V+3R3_EUP
GNDD
C1065 R1163
GNDD
BACK
GNDD
MEMORY
V+3R3_EUP
5
6
IC1004 C1039
C1064
GNDA
C1066
DELETE
E
C1019
IC1004
C1028 R1037

C1035 C1025 C1072
C1009
GNDA
L1001
CDJ-850
C1018 10 C1010
0
A
C1038 R1151
1 100 C1008 GNDA
Q1021
1
15 C1015
R1088 C1005 1 95
GNDD
E
R1020
110
1 90
CALL >
R1079 C1029
V+3R3_EUP
C
11
15
R1085 1 85 C1012
F
E
1 20
V+3R3_SW R1059
1 C1013
215
1 C1011
3
Q1022
3
R1143 30 1 80 C1014 R1065

Q1021 Q1022
V+38 1 30
R1017 R1100
IC1007
75 80
R1144 70
GNDD R1099
< CALL
35 R1013
R1072 R1142
65
C1070
IC1007
C1078 40 60
21
C1034
GNDD
MENU
45 55
E
L1003
GNDD
Q1013
V+38
R1186 R1075 50 C1032

C1031 50 C1076
2
Q1013 GNDD
R1044 C1027 R1019

R1043 R1042 R1090 GNDD GNDD
L1011
3
C1077
V+3R3_SW
R1089
C1021 L1008
C1062 R1083 R1034
V+12 R1027 V+3R3_EUP
1
C1063 R1067 R1035
V+3R3_EUP R1031 R1058 R1097
D1024 R1014
C1071 R1094
R1063 R1026 R1036
IC1001
R1039
4
R1082 R1069 R1150 R1015
V+6R6_FL
C1024
5
R1033 R1121
GNDD
C1017
C1023 R1180
4
C1043
4
INFO
D1009 C1022 R1074

1
R1124
IC1001
V+3R3_EUP
C1007 R1076
E
Q1012
R1021 V+3R3_EUP
V+3R3_EUP
C1079
Q1012
C1073 R1080
R1023 L1005
R1092
GNDD
R1166
[[ G ]]
C1004 R1123
C7
R1165
V+6R6_FL
V+12
R1164
C1074 R1122
C1041 L1009 R1188 R1173 R1125
C1047 C1042
R1179 R1134
TAG LIST
R1172
GNDD
GNDD
C1050 C1049 C1045 R1040

R1107 Q1023 V+3R3_EUP R1087
R1174
Q102
R1118 R R1055
R1023 L1005
R1092
NDD
R1166
[[ G ]]
C1004 R1123
C7
R1165
+6R6_FL
V+12
R1164
C1074 R1122
C1041 L1009 R1188 R1173 R1125
C1047 C1042
R1179 R1134
TAG LIST
R1172
GNDD
GNDD
C1050 C1049 C1045 R1040
R1107 Q1023 V+3R3_EUP R1087
R1118 R1174 R1055
E
R1061 R1081
C1058 R1175 R1049
R1177 R1176 Q1024
C1053 R1155
E
GNDD
E
C1055 Q1025 C1068
Q1020
E
5
R1154
5
R1117 GNDD
D1017
Q1011
E
R1116
1
R1153
GNDD
5
Q1018
R1115
Q1011
19
Q1025 Q1018
R1114
E
D1018 R1109 V+3R3_EUP
Q1019
C1067
C1048
Q1023 Q1024 Q1020 Q1019
R1060 R1152
C1069
C1057 R1156
E
RELOOP C1059 R1158
C1060 R1070
E
BROWSE R1066
Q1016
R1187
E Q1006
Q1016 Q1017
V+38
Q1017
Q1006
GNDD
20
L1007
L1010
GNDD
GNDD
R1131 R1132
E
GNDD
V+12
R1133
Q1009
GNDD
R1128 R1127
Q1009
C1075 R1126 V+6R6

R1129
V+6R6
6
R1130
6
GNDD
GNDD
R1185
V+6R6 R1002 R1001
R1050
LINK
GNDD DISC
USB
LOOP OUT
E
LF
Q1005
Q1005
R1181 R1182
16.GNDD
TIME
V+12
CDJ-850
14.GNDD
DFLB
GNDD
R1012 R1184
13.PNL_RST
9.PWR_ON
15.PNL_CNVSS
10.MAIN_RST
11.USB_STOP
R1010 R1004
12.MAIN_BUSY
DWX3152- /J
GNDD
8.PNL_XMUTE
5.V+12
4.V+12
GNDD
7.VDET
6.GNDD
3.GNDD
1.GNDD
E
E
E
R1003
Q1003
Q1002
Q1001
Q1003
Q1002
Q1001
R1011 R1008
2.V+12_EUP
V+6R6
LOOP IN
7
7
GNDD
R1029
GNDD
GNDD
19.TSI
E
21.TSO
GNDD
17.TSCK
18.GNDD
V+6R6
Q1004
20.PNL_BUSY
V+12_EUP
21 1
GNDD
Q1004
CONTACT SIDE
B
CN1001
8
8
G
SIDE B
109
F
E
B
A
D
C
1 2 3 4
11.5 KSW1 and KSW2 ASSYS

SIDE A SIDE A
A
H KSW1 ASSY
J1205
D1201 J1224
J1229
USB
S1207
J1202
STOP J1215
J1222
I KSW2 ASSY
J1211
J1226
J1214
J1209
J1207
B J1213
J1203
J1217 TRACK SEARCH
D1203
J1231
J1204
J1210
S1201
1 J1228 JUMPER S1403 S1404
J1206
J1208
KSW2
DWS1426- /J
G H
D1204
S1202
SEARCH
J1218
KSW1
C 2 S1405 S1406
J1219
DWS1422- /J
S1203
4
J1221
J1201
D1205
J1225
D1402
D1404
S1204
D1206
D
J1212
8 J1216
CUE
Production code
S1401
J1227
J1401
J1220
CN
J1230
140
1
BEAT J1402
CN1401
SELECT
1
1
Production Code
S1205
5
7
E
D1401
D1403
D1207
D1202
PLAY
S1402
REV
S1206
J1223
(DNP2601-C)
1 JH1201 7
1 5 (DNP2601-C)
F JH1201
H I
110 CDJ-850
1 2 3 4
5 6 7 8
SIDE B SIDE B
A
H KSW1 ASSY
USB_ACT
_LED
Q1201
R1211
Q1201
R1201
E
USB_STOP
1KEY_SW
2KEY_SW
I KSW2 ASSY
C1207
USB STOP
4KEY_SW
GNDD
8KEY_SW V+6R6
1KEY_LED
2KEY_LED
R1212
4KEY_LED B
R1204
8KEY_LED
REV_LED
TRACK SEARCH SHIFT_SW
REV_SW
CUE_SW
Q1202
1
Q1202
PLAY_SW
C1201
R1409 E
C1202
V+6R6
GNDD
R1213
R1410
R1215
GNDD
R1206
C1403 SEARCH
CUE_LED
2
R1411 Q1203
E C
Q1203
GNDD
LF
R1208
R1214
4
C7
[[ G ]]
C1203
C1206
Q1204
GNDD
KSWB
V+6R6
Q1204 GNDD
E
DWS1426- /J
R1210
8
D
Q1401
Q1401
R1401
CUE Q1205 PLAY_LED
E
C1401
KEY2_B Q1205
1.V+6R6
2.GNDD
3.CUE_LED
4.CUE_SW V+6R6
5.PLAY_LED
6.PLAY_SW
7.KEY2_B
DWS1422- /J
V+6R6
GNDD
R1216
GNDD
CN1401
LF [[ G ]] KSW1
1
C1204
R1413
C7
5.PLAY_LED
6.PLAY_SW
3.CUE_LED
4.CUE_SW
7.KEY2_B
1.V+6R6
2.GNDD
B_SHIFT
R1404
R1403
7
Q1402
E
Q1402 E
R1217
C1402
R1412
E
PLAY
Q1206
C1205
Q1206
R1203
(DNP2601-C)
REV
7 1
(DNP2601-C)
JH1201 F
H I
CDJ-850 111
5 6 7 8
1 2 3 4
11.6 JFLB and JOGB ASSYS

SIDE A SIDE A
A
G CN1002
J JFLB ASSY
CN1802
5 CONTACT SIDE
T1801 5 1
13 1
10
C1817
CN1802
1
C1803
J1841
B
J1820
J1838
J1836
J1843
J1844
J1845
J1810
J1815
J1803
J1807
J1834
C1826
J1830 SHEET
SW
1
J1808
CN
J1811
J1816
J1835 18
01
J1824
J1823
J1840
5
IC1802
1
C1824
J1813
J1837
IC1803 5 J1802
CN
18
J1809
01
J1822
J1805
J1801
J1833
J1814
J1819
C1812
C
J1829
J1826
1 C1831
J1831
Q1803
J1806
J1827
E
C1815
J1825
J1842
J1812
J1804
L1802
J1818
J1832
J1839
J1817
Production Code
J1828
1 10 25 30
V1801
Q1801 J1821
E
C1801
D
DWX3154- /J
E
JH1801
JH1801
JFLB
C1807
Q1802
1
(DNP2601-C)
IC1802 Q1801 Q1803

IC1803 Q1802
K JOGB ASSY
4.GNDD
3.V+3R3
1
2.JOG1
1.JOG2
JOGB
1
CN1901
1
1
PC1901
5
2.V+3R3
3.JOG1
4.GNDD
1.JOG2
DWX3155-
4
CN1901 /J
(DNP2601-C)
F
J K
112 CDJ-850
1 2 3 4
SIDE B
C
J
N1
8
5
5
1
01
3
JFLB LF
D1801
R1813 C1802
1
2.NC
DWX3154- /J
3.GNDD
[[ G ]]
1.JOG_SW
C7
C1902
JFLB ASSY
CONTACT SIDE
1.V+3R3_SW
C1901
2.GNDD
GNDD
4 1 C1813
CN1802
3.J_LAT
R1903
R1857 C1832 R1810
13
R1811 4.J_SCLK
1.JOG2
2.JOG1
4.GNDD
R1812 5.J_BK
VFDP2R7_F2
R1844 6.J_DSO
R1814 7.JOG_SW
3.V+3R3_SW
GNDD
GNDD
R1845
[[ G ]] R1815 8.JOG2
R1901
R1816
V+3R3_SW
GNDD R1853 R1852 9.JOG1
R1902
C1804
C7 R1851 R1850 10.GNDD
R1847 R1846 11.V+38
DWX3155- /J
4 1 12.GNDD
1 4 GNDD 13.V+12
R1849
JOGB
R1821
6
V+38
6
GNDD
GNDD
GNDD
(DNP2601-C)
LF C1808
K JOGB ASSY
C1809 R1848
R1856
1
C1810 R1820 D1802
Q1808
JH1801
Q1808
CN1901 R1841 C1811 D1804
R1843 R1819
3
C1806 V+12
E
R1855
Q1805
R1854 GNDD
E
23
2
VFDP2R7_F2
E
R1817
V+3R3_SW
Q1805 Q1804
V+27SW
Q1806
Q1806
4
Q1804
V+12 V+12
R1818 C1819
CDJ-850
GNDD C1818
GNDD L1801
R1803 GNDD
R1807 GNDD
R1808 C1816
R1804 C1814
R1806 VFDP2R7_F1
R1802
R1801 D1803
7
7
R1805 VFDP2R7_F1 R1842 R1840
0 1 A
B
24
0 1 2 3 0 1 2 3 4 5 6 7 8 9 C
D1806
V+12
0 1
V+27SW
D1808
Q1807
Q1807
R1831
V+27 R1827 R1833

R1825
25
D1805 C1828
R1823
R1837 C1820
R1824 R1830 R1826
R1838
D1809
GNDD
C1830 R1829
C1823
(DNP2601-C)
R1822
R1828 C1825
R1839
C1822
C1821
V+27SW C1827
C1829 D1807
8
8
R1836
22
R1832
V+12
R1835 R1834
1
P1801
J K
SIDE B
113
F
E
B
A
D
C
1 2 3 4
11.7 SLD1, PSWB and SLD2 ASSYS

SIDE A SIDE A
A J1324
L M PSWB ASSY
J1313 D1301
SLD1 ASSY EUP_LED B (DNP2601-C)
S1601
Production Code
DWS1424- /J
EJECT
PSWB
D1304
J1305
J1322
CN1601
S1301
J1317 1
J1319 3 1
J1308
JUMPER
J1304
A N SLD2 ASSY
J1323
J1314 CN1601
G L
J1303
J1310 J1318
1
JH1302
1
J1306
J1307
3
JH1302
J1320 J1321
J1316
J1503
1
CN1501
1
1
C J1502
4
VR1301
CN1501
J1315
TOUCH/RELEASE
J1311 J1501
SLD2
SLD1
DWS1423- /J
D
VR1501
D1302
S1302
VINYL
J1302 J1301
J1309
DWS1427- /J
Production Code
J1312
E
JH1301
JH1301
4
Production Code
TEMPO
S1303
1
1
MASTER TEMPO
D1303
S1304
1
C1501
(DNP2601-C)
L M N (DNP2601-C)
114 CDJ-850
1 2 3 4
5 6 7 8
SIDE B SIDE B
A
V+6R6
EUP_LED
M PSWB ASSY L
R1307
(DNP2601-C)
GNDD SLD1 ASSY
R1306
C1307
GNDD
V+6R6
DWS1424- /J
Q1302
PWR_SW
EJECT
EUP_LED
R1601
PSWB
V+6R6
E
Q1302
LF 1 3
R1309
R1319 R1310
[[ G ]]
C7
PWR_SW
GNDD
GNDD
B
L1302
N SLD2 ASSY EJECT_LED
R1302
KEY0
CN1601
TCH/REL
VINYL_LED MT_LED
C1502
D1502 D1501
JH1302
1.PWR_SW
R1504
1
2.GNDD
3.GNDD
GNDD GNDA
ADCT
3
R1503
V+6R6 ADIN
V+3R3_EUP
ADDITIONAL
bend
SOLDER
CN1501
1
1.ADCT C
R1301
2.ADIN
3.GNDA 1
4.V+3R3_EUP D1305
C1304
4
TOUCH/RELEASE
C1305
L1301
V+3R3_EUP
ADD SOLDER
GNDA
V+3R3_EUP
DWS1427- /J
[[ G ]]
L1303
C7
R1318
Q1303 R1316
C7
[[ G ]]
E D
SLD2
DWS1423- /J
Q1303
LF
R1311
R1315
R1313
R1314
R1317
E E
Q1304
Q1305
R1303
Q1305
Q1304
VINYL
V+3R3_EUP
GNDA
GNDA
V+6R6
ADDITIONAL
E
R1304
SOLDER
SLD1
JH1301
4
bend
TEMPO
LF
R1305
4.V+3R3_EUP
3.GNDA
R1312
2.ADIN
C1503
D1504
1.ADCT
MASTER TEMPO
L1304
C1306
D1503
Q1301
E F
Q1301
(DNP2601-C) (DNP2601-C)
L M N
CDJ-850 115
5 6 7 8
1 2 3 4
11.8 POWER SUPPLY and ACIN ASSYS

SIDE A SIDE A
A
O POWER SUPPLY ASSY

CN2001
CN2
B
E
AC POWER CORD
JA2401 P ACIN ASSY

PRIMARY
JA2401
E 1
LIVE NEUTRAL
DWX3158- /J
JP2402
DWX3173- /J
JP2401
PURPLE BLUE
ACIN
(DNP2601-C)
CN1
O P
116 CDJ-850
1 2 3 4
5 6 7 8
SIDE B SIDE B
A
O POWER SUPPLY ASSY
CN2
B
P ACIN ASSY JA2401
ADDITIONAL
PRIMARY
SOLDER
ACIN
NEUTRAL LIVE LF
DWX3158- /J
DWX3173- /J
[[ G ]]
C7
ADDITIONAL
SOLDER
(DNP2601-C)
CN1
O P
CDJ-850 117
5 6 7 8
1 2 3 4
12. PCB PARTS LIST

A - The > mark found on some component parts indicates the importance of the safety factor of the part.
- When ordering resistors, first convert resistance values into code form as shown in the following examples.
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47 k ohm (tolerance is shown by J = 5%,
and K = 10%).
560 Ω → 56 × 101 → 561 ................................................................... RD1/4PU 5 6 1 J
47 kΩ → 47 × 103 → 473 ................................................................... RD1/4PU 4 7 3 J
0.5 Ω → R50 ................................................................................................. RN2H R 5 0 K
1Ω → 1R0 ................................................................................................. RS1P 1 R 0 K
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).
5.62 kΩ → 562 × 101 → 5621 ................................................................. RN1/4PC 5 6 2 1 F
- Meaning of the figures and others in the parentheses in the parts list.
B
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board.
IC 301 (A, 91, 111) IC NJM2068V
LIST OF ASSEMBLIES
1..MAIN ASSY DWX3174
B SLMB ASSY
MISCELLANEOUS
S 1701,1702 PUSH SWITCH DSG1017
NSP 1..SUB1 ASSY (SYXJ8, FLXJ, KXJ5, AXJ5) DWM2399
CN 1701 5P CONNECTOR VKN1265
NSP 1..SUB1 ASSY (CUXJ) DWM2405
NSP 2..KSW1 ASSY DWS1422
NSP 2..SLD1 ASSY DWS1423
C 2..PSWB ASSY DWS1424
C JINT ASSY
MISCELLANEOUS
2..SLMB ASSY DWS1425
2..KSW2 ASSY DWS1426 CN 2301 CONNECTOR DKN1312
CN 2302 24P FFC CONNECTOR DKN1445
2..SLD2 ASSY DWS1427
2..DFLB ASSY DWX3152 *
2..JFLB ASSY DWX3154 CN 2304 4P CONNECTOR DKN1288
CN 2305 CONNECTOR DKN1407
2..JOGB ASSY DWX3155
2..ACIN ASSY (SYXJ8, FLXJ, KXJ5, AXJ5) DWX3158 RESISTORS
2..ACIN ASSY (CUXJ) DWX3173 All Resistors RS1/10SR###J
NSP 1..SUB2 ASSY DWM2400 CAPACITORS

D 2..CNCT ASSY DWX3151 C 2301,2307 CKSRYB103K50
2..CMPX ASSY DWX3153
2..USBA ASSY DWX3156
>
2..JINT ASSY
1..POWER SUPPLY ASSY

DWX3157
DWR1463
D MAIN ASSY
SEMICONDUCTORS
IC 101 DYW1796
IC 102 K4S561632J-UC75
or
∗ The service part of DFLB Assy (DWX3152) is supplied with H57V2562GTR-75C
KSW1 Assy (DWS1422) and SLD1 Assy (DWS1423). IC 103 R5S72630P200FP
(There assemblies are connected with the jumper wires.) IC 105 TC74VHCU04FT
IC 107 TS3USB30RSW
E
Mark No. Description Part No. IC 201 TC94A15FG
A CNCT ASSY
IC 203 NJM2903M
IC 204 BD7956FS
MISCELLANEOUS IC 205 TC7W04FU
L 2501,2502 INDUCTOR CTF1410 > IC 206 BA00BC0WFP
S 2501 SLIDE SWITCH VSH1018
CN 2501,2502 24P FFC CONNECTOR DKN1445 IC 301 DSPC56371AF180
IC 302 PCM1742KE
CAPACITORS IC 303 RNB4580F
> IC 401 BA33BC0WFP
C 2501,2505 CKSRYB104K16
> IC 402,408 S-1170B33UC-OTS
C 2502,2503 CKSRYB103K50
F C 2504,2506 DCH1201
> IC 403,404 BD00KA5WFP
> IC 405,406 NJM2872BF05
> IC 409 BD9326EFJ
Q 101,405,408 HN1C01FU
118 CDJ-850
1 2 3 4
5 6 7 8
Q 102,109,410,413 LTC124EUB C 101,103-105,107 CKSSYB104K10
C 102,124,152,186 CKSSYB103K16
Q 104,107,303 RT3T22M C 106,114,117,119 VCG1063
Q 201 2SA1036K C 108,122,126,150 CCSSCH331J50 A
Q 402,404,406,415 2SA1576A C 109,110,214,320 CEHVAW101M6R3
Q 411 LSC4081UB
Q 414 LTA124EUB C 111-113,115,116 CKSSYB104K10
C 118,120,125 CKSSYB104K10
D 101,103,405,406 1SS352 C 121,123,130,131 VCG1063
D 401 RSX201L-30 C 127-129,132,133 CKSSYB104K10
C 134,138,143,154 VCG1063
MISCELLANEOUS
L 201-226,407,408 INDUCTOR CTF1545 C 135-137,139-142 CKSSYB104K10
L 227-229 INDUCTOR CTF1745 C 144-147,151,153 CKSSYB104K10
L 403 INDUCTOR CTH1254 C 148,169 CCSRCH100D50
F 101,102,301 EMI FILTER DTL1106 C 149,167 CCSRCH9R0D50
B
F 401,402 FILTER CTF1701 C 155-158,160 CKSSYB104K10
KN 404 WRAPPING TERMINAL CKF1089 C 159,161,165,179 VCG1063

X 101 CRYSTAL (33 MHz) DSS1193 C 162-164,170,174 CKSSYB104K10
X 102 CRYSTAL (48.000 MHz) ASS7099 C 166,437 CKSRYB474K10
X 103 CRYSTAL RESONATOR (16.9344 MHz) VSS1084 C 171,173 CCSRCH180J50
CN 201 CONNECTOR DKN1404 C 176-178,272,274 CCSSCH331J50
CN 401 CONNECTOR AKM1299 C 180,187-193,211 VCG1063

CN 402 27P CONNECTOR RKN1068 C 184,254,271 CCSSCH101J50
CN 403 17P CONNECTOR RKN1058 C 194,210,231,235 CKSSYB103K16
C 201,204,209,212 CKSSYB104K10
RESISTORS C 202,225,239,318 CEHVAW470M6R3 C
R 101,102,106,107 RAB4CQ330J
R 103-105,108 RAB4CQ560J C 203 CCSSCH470J50
R 110-113,132 RAB4CQ330J C 205,220 CKSSYB153K16
R 134-136,138 RAB4CQ330J C 206,207 CKSSYB223K16
R 156 RS1/16SS5601F C 208 CKSSYB102K50
C 213,217-219 CKSSYB104K10
R 166,339,345,602 RS1/10SR0R0J
R 186-188 RAB4CQ560J C 215 CKSSYB471K50
R 255 RS1/10SR222J C 216 CKSSYB681K50
R 258,260-262 RS1/4SA1R0J C 221-224,230,233 CKSSYB104K10
R 263,264 RS1/4SA2R7J C 227 CCSSCH680J50
C 228,246,247,252 CEHVAW470M16
R 265 RS1/10SR1002F D
R 272,273 RS1/10SR683J C 232,238 CKSSYB333K10
R 287,458 RS1/16SS1502F C 234,236,237,253 CKSSYB104K10
R 288 RS1/16SS1003F C 241 CKSRYB333K25
R 289,422,426 RS1/16SS3302F C 242 CKSSYB331K50
C 243 CKSSYB271K50
R 291,411,423,459 RS1/16SS1202F
R 323,324,356,357 RS1/16SS4702D C 244,245,250,263 CKSSYB104K16
R 325,326 RS1/16SS2200D C 248 CCSSCH471J50
R 327,328,469 RS1/16SS2201D C 249,251,260,262 CKSSYB103K16
R 329,332 RS1/16SS4701D C 255 CKSRYB122K50
C 256,259,301-303 CKSSYB104K10
R 330,331 RS1/16SS3301D
R 333,334 RS1/16SS5101D C 257,258 CKSRYB222K50 E
R 410,485 RS1/16SS3601F C 261,264,267,279 VCG1063
R 421 RS1/16SS2202F C 265,436,455,461 CKSRYB104K16
R 424 RS1/16SS1102F C 266,281,496 CKSRYB103K50
C 268,276,278,340 CKSQYB225K10
R 427 RS1/16SS5602F
R 436 RS1/16SS3301F C 275,308,311,335 CCSSCH331J50
R 467 RS1/16SS7500F C 280,283,309,312 VCG1063
R 468 RS1/16SS1102D C 282,304,305,307 CKSSYB103K16
R 470,471,483 RS1/4SA0R0J C 306,310,313,314 CKSSYB104K10
C 315,411,412 CEHVAW220M6R3
R 472-474,480,481 RS1/10SR330J
R 484,502 RS1/16SS1002F C 316,445,451,468 CCSRCH102J50
R 501 RS1/16SS1202F C 317,400,418,430 VCG1063 F
Other Resistors RS1/16SS###J C 319,321,403,407 CKSSYB104K10
C 322,323,405,406 CEHVAW101M6R3
CAPACITORS C 326,327 CCSRCH181J50
CDJ-850 119
5 6 7 8
1 2 3 4
C 328,329 CCSRCH330J50 CN 2004 PLUG (13P) KM200NA13

C 331,333,431,448 CEHVAW470M16 CN 2005 5P JUMPER CONNECTOR 52147-0510
A C 341,499,502 CKSQYB225K10 CN 2006 17P CONNECTOR VKN1248
C 342,414,416,435 CKSSYB103K16 CN 2007 PLUG (9P) KM200NA9
C 401,402,415,417 CKSRYB105K10 > P 2003 PROTECTOR (0.500 A) DEK1095
C 404,422,424,427 DCH1165 > P 2004 PROTECTOR (0.375 A) DEK1094

C 408,420,423,438 CKSSYB104K10
C 409,410 CKSSYB105K6R3 RESISTORS
C 413,428,432 CKSSYB104K16 R 2002 RST1/2SP120J
C 419 CKSRYB105K10 R 2004 RS1/10SR6802D
R 2005 RS1/10SR4701D
C 421,434,497,506 CCSSCH331J50 R 2006 RS1/10SR5101D
C 440 CKSSYB222K50 R 2026,2027,2047-2049 RS1/8SQ0R0J
C 442,443 DCH1165
B
C 444,453,458-460 CKSSYB104K10 R 2051,2089,2090 RS1/8SQ0R0J
C 462,475,478,480 CKSSYB104K10 R 2059,2060 RS1/8SQ473J
R 2061,2062,2066,2067 RS1/8SQ151J
C 467,472-474,495 VCG1063 R 2076,2080 RS1/8SQ272J
C 470,498,504 CKSSYB103K16 R 2077-2079,2081 RS1/8SQ222J
C 471 CCSRCH102J50
C 483-485 CKSSYB221K50 Other Resistors RS1/10SR###J
C 486-488,490 CCSSCH101J50
CAPACITORS
C 492-494 CCSSCH101J50 C 2001,2077,2079,2102 CKSRYB104K50
C 501 VCG1063 C 2002,2004,2015,2097 CCG1221
C 507 CCSSCH331J50 C 2003,2012,2090,2091 ACG1142
C C 2005,2022,2093 CEHVAW470M16
C 2006 CCSRCH102J50
E CMPX ASSY
SEMICONDUCTORS
C
C
2007,2008
2009,2074,2078,2080
CKSRYB222K50
CKSRYB103K50
> IC 2001 SI-8005Q C 2010,2011,2073 CKSRYB105K16
> IC 2002 NJM2845DL1-05 C 2014 CCSRCH122J50
IC 2003 BD2051AFJ C 2019 CKSRYB224K16
Q 2014-2017 2SD2704K
Q 2018 2SA1576A C 2020 CCH1565
C 2021 CKSRYB104K16
Q 2019 UMD2N C 2033 CKSRYB474K10
Q 2021 LTC124EUB C 2036 DCH1201
D Q 2026,2032 LTC143EUB C 2075,2076 CEVW221M10
Q 2027 LTA124EUB
Q 2028 2SB1698 C 2082,2083 CFHXSQ471J50
C 2084,2086 CKSRYB103K50
Q 2029 IMX2 C 2088 CEVW471M16
Q 2030 IMT2A C 2092,2094 CKSQYB475K16
Q 2031 2SD2662 C 2095,2096 CKSQYB105K16
Q 2033 RN1902
D 2002 CMS03
D
D
2003,2004
2005,2011,2012
EP05Q06
1SS352
F USBA ASSY
SEMICONDUCTORS
D 2014 NNCD6.2MF D 2201 NNCD6.2MF
E D 2016 1SS355
D 2017,2018 UDZS10(B) MISCELLANEOUS
JA 2201 USB CONNECTOR DKB1106
D 2019 UDZS6R2(B) JH 2201 5P CABLE HOLDER 51048-0500
JP 2201 JUMPER WIRE D20PDY0510E
MISCELLANEOUS
L 2001,2003,2006,2017 INDUCTOR CTF1488 CAPACITORS
L 2002 INDUCTOR CTH1253 C 2201 CEHVAW101M6R3
L 2014,2015 CHIP SOLID INDUCTOR XTL3010 C 2202 CKSRYB103K50
F 2001 FILTER CTF1701 C 2203 CEVQW220M16
JA 2001 USB CONNECTOR DKN1237 C 2204 CCSRCH102J50
JA 2002 JACK VKB1243

F JA 2003 PIN JACK (2P) AKB7181
CN 2001
CN 2002
CONNECTOR
27P CONNECTOR
B6B-XH-A
VKN1258
G DFLB ASSY
SEMICONDUCTORS
CN 2003 21P CONNECTOR VKN1252 > IC 1001 NJM2392M
120 CDJ-850
1 2 3 4
5 6 7 8
IC 1004 BD45302G C 1035,1044,1046,1049 CKSRYB103K50
> IC 1006 SI-8105QL
IC 1007 PEG799A8 C 1036,1041,1072 CKSRYB104K16
Q 1001-1006,1009 LTC124EUB C 1047,1064-1066 CCSRCH102J50 A
C 1048 CKSQYB102K50
Q 1011-1013,1019,1020 LTC124EUB C 1050 CKSRYB103K50
Q 1014 LTA124EUB C 1055 CCSRCH182J50
Q 1016,1017 2SC4081
Q 1018 RTQ040P02 C 1061 DCH1324
Q 1021 2SD1898 C 1063,1076 DCH1201
C 1067 CKSRYB474K16
Q 1022-1024 2SA1576A C 1070 CKSRYB105K16
Q 1025 LTC124EUB C 1074,1075 CCSRCH470J50
D 1001,1007,1010,1012 SLI-343Y8C(KLMN)
D 1002,1003,1013-1016 SLI-343M8C(FGHJ) C 1077 CCSRCH101J50
D 1009 EP05Q06
B
D 1018
MISCELLANEOUS
CMS03
H KSW1 ASSY
SEMICONDUCTORS
L 1001,1003,1008-1010 INDUCTOR CTF1579 Q 1201-1206 LTC124EUB
L 1002 RADIAL LEAD INDUCTER DTH1206 D 1201,1202,1207 SLI-343U8RC(HJKL)
L 1004,1007,1012 INDUCTOR CTF1378 D 1203-1206 SLI-343Y8C(KLMN)
L 1005 INDUCTOR CTF1357
L 1006 POWER INDUCTOR DTL1185 MISCELLANEOUS
S 1201-1206 TACT SWITCH DSG1079
L 1011 INDUCTOR CTF1334 S 1207 SWITCH VSG1024
V 1001 VFD DEL1069
S 1001-1004,1007-1009 SWITCH VSG1024 RESISTORS C
S 1005,1006,1010 TACT SWITCH DSG1079 All Resistors RS1/10SR###J
S 1011-1017 SWITCH VSG1024
MISCELLANEOUS
S 1018 ROTARY SW YSD5019 JH 1201 7P CABLE HOLDER 51048-0700
X 1001 CRYSTAL RESONATOR (15.975 MHz) DSS1166 JP 1201 JUMPER WIRE D20PDY0720E
0 FL HOLDER DNF1862
RESISTORS
I KSW2 ASSY
SEMICONDUCTORS
R 1021 RS1/4SA2R7J Q 1401,1402 LTC124EUB
R 1042,1173 RS1/10SR3301D D 1401,1403 SLI-343M8C(FGHJ)
R 1043,1172 RS1/10SR3302D D 1402,1404 SLI-343Y8C(KLMN) D
R 1044 RS1/10SR2202D
R 1109 RST1/2SP120J MISCELLANEOUS
S 1401,1402 TACT SWITCH DSG1117
R 1114 RS1/10SR5602D
S 1403-1406 SWITCH VSG1024
R 1115 RS1/10SR1501D
CN 1401 7P JUMPER CONNECTOR 52147-0710
R 1116,1175,1176 RS1/10SR4701D
R 1142 RS1/10SR2701F
RESISTORS
R 1144 RS1/10SR1001F
All Resistors RS1/10SR###J
R 1145-1149 RS1/4SA240J
Other Resistors RS1/10SR###J
CAPACITORS J JFLB ASSY

SEMICONDUCTORS
E
C 1004,1042,1045,1057 ACG1128
> IC 1802 TLC555IP
C 1005,1031,1034,1062 DCH1201
> IC 1803 NJM2374AD
C 1006 CEHAZL680M16
Q 1801,1802 2SC1815
C 1007,1079 CKSRYB104K50
Q 1803 2SB1237X
C 1008,1017,1029,1032 CKSRYB104K16
Q 1804,1806 LTC124EUB
C 1009-1014,1018,1019 CCSRCH102J50
Q 1805,1808 2SD1767
C 1015 CKSRYB474K10
Q 1807 RHP020N06
C 1016 CEHAS101M10
D 1801 UDZS6R8(B)
C 1021,1038,1040,1043 CCSRCH470J50
D 1802,1803,1805,1806 RB160M-60
C 1022,1023 CCSRCH220J50
D 1804 UDZS10(B)
C 1024 CCSRCH560J50 F
D 1807 1SS355
C 1025,1028 CCSRCH270J50
D 1808,1809 RB160M-60
C 1027,1078 CCSRCH221J50
C 1030 CEHAZL221M6R3
CDJ-850 121
5 6 7 8
1 2 3 4
MISCELLANEOUS
L 1801
L 1802
INDUCTOR
POWER INDUCTOR
CTF1579
DTL1187
L SLD1 ASSY
SEMICONDUCTORS
A
V 1801 FL INDICATOR TUBE DEL1058 Q 1301-1303 LTC124EUB
T 1801 POWER TRANSFOMER DTT1232 Q 1304,1305 2SA1576A
CN 1801 CONNECTOR CKS1072 D 1301,1303 SLI-343U8RC(HJKL)
D 1302 SLR343BC4T(JKLM)
CN 1802 13P CONNECTOR VKN1244 D 1304 SLI-343M8C(FGHJ)
0 FL HOLDER DNF1735
JH 1801 4P CABLE HOLDER 51048-0400 MISCELLANEOUS
JP 1801 JUMPER WIRE D20PYY0405E L 1302-1304 INDUCTOR CTF1334
VR 1301 POTENTIOMETER DCS1062
RESISTORS S 1301-1304 SWITCH VSG1024
R 1820,1821,1848,1849 RS1/4SA102J
R 1822 RST1/2SP1R0J RESISTORS
B R 1823 RS1/4SA0R0J All Resistors RS1/10SR###J
R 1824 RS1/4SAR51J
R 1825 RS1/4SA331J MISCELLANEOUS
JH 1301 4P CABLE HOLDER 51048-0400
R 1826 RS1/8SQ102J JH 1302 3P CABLE HOLDER 51048-0300
R 1827 RS1/8SQ101J JP 1301 JUMPER WIRE D20PDY0410E
R 1828,1832 RS1/4SA271J JP 1302 3P JUMPER WIRE D20PDY0310E
R 1829,1830 RS1/8SQ181J
R 1833 RS1/4SA103J CAPACITORS
C 1307 CKSRYB103K50
R 1834 RS1/10SR1201D
R 1835 RS1/10SR1602D
R 1836 RS1/10SR6802D
C R
R
1837
1838,1839
RS1/10SR4302D
RS1/10SR2201D
M PSWB ASSY
MISCELLANEOUS
S 1601 PUSH SW ASG1102
R 1840 RS1/8SQ223J
R 1846,1847,1850-1853 RS1/4SA222J
Other Resistors RS1/10SR###J
RESISTORS
CAPACITORS
C 1802 CKSRYB223K16
C 1803 CEHAR470M16
C
C
1804,1806
1808
CKSRYB104K16
CCSRCH470J50
N SLD2 ASSY
SEMICONDUCTORS
C 1809-1811,1821 CCSRCH101J50
D 1501-1504 1SS352
D
C 1812 CEHAZL100M50
C 1813,1823,1827,1828 CKSRYB104K50
MISCELLANEOUS
C 1814,1816 CCG1255 VR 1501 VR DCV1009
C 1815 CEHAR101M10
C 1817 CEHAR100M50
CAPACITORS
C 1818,1819 ACG1147 C 1501 CEJQ470M16
C 1820 CCSRCH221J50 C 1502,1503 CKSRYB104K16
C 1824,1831 CEHAZL220M50
C 1826 CEHAZL221M25-P35
E
C 1829 CCSRCH331J50
O POWER SUPPLY ASSY
There is no service parts.
K JOGB ASSY
MISCELLANEOUS
CN 1901 4P JUMPER CONNECTOR 52151-0410 P ACIN ASSY (DWX3158)
MISCELLANEOUS
> JA 2401 AC INLET DKP3889
RESISTORS
> JP 2401 CONNECTOR ASSY 2P DKP3870
MISCELLANEOUS
PC 1901 PHOTO INTERRUPTER SEDS-7573
P ACIN ASSY (DWX3173)
MISCELLANEOUS
F CAPACITORS
> JA 2401 AC INLET DKP3891
C 1901,1902 CKSRYB103K50
> JP 2401 CONNECTOR ASSY 2P DKP3870
122 CDJ-850
1 2 3 4

Multi Player: This Manual Is Applicable To The Following Model (S) and Type (S)

Uploaded by

Copyright:

Available Formats

Multi Player: This Manual Is Applicable To The Following Model (S) and Type (S)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Multi Player: This Manual Is Applicable To The Following Model (S) and Type (S)

Uploaded by

Copyright:

Available Formats

ORDER NO.

CDJ-850 SYXJ8 AC 220 V to 240 V

CDJ-850 CUXJ AC 120 V

CDJ-850 FLXJ AC 110 V to 240 V

CDJ-850 AXJ5 AC 220 V to 240 V

For details, refer to "Important Check Points for good servicing".

PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan

CLASS 1 LASER PRODUCT

Additional Laser Caution

(Printed on the chassis) (Printed on the chassis) (Printed on the chassis)

SYXJ8 CUXJ FLXJ

(Printed on the chassis) (Printed on the chassis)

1 Use specified parts for repair.

Use genuine parts. Be sure to use important parts for safety.

2 Do not perform modifications without proper instructions.

3 Make sure the soldering of repaired locations is properly performed.

4 Make sure the screws are tightly fastened.

5 Make sure each connectors are correctly inserted.

9 There should be no spark traces or similar marks on the power plug.

a Safe environment should be secured during servicing.

E 3. Lubricants, Glues, and Replacement parts

5. Shipping mode and Shipping screws

Do NOT use a soldering iron whose tip temperature cannot be controlled.

The following lead-free solders are available as service parts:

1.2 ABOUT POWER SUPPLY MONITORING

USB downstream section (USB)

USB upstream section (USB)

• The specifications and design of this product are subject to

2.2 USABLE DISCS AND USB DEVICES

2.3 PANEL FACILITIES

3. BASIC ITEMS FOR SERVICE

No. Procedures Check points

Check the connection of each interface.

3.2 JIGS LIST D

Lubricants and Glues List

Name Part No. Remarks

Cleaning paper GED-008 "9.5 SLOTIN MECHA SECTION".

3.3 PCB LOCATIONS

G DFLB ASSY H KSW1 ASSY F USBA ASSY E CMPX ASSY

SLOTIN MECHA ASSY

O POWER SUPPLY ASSY

F 1..TM ASSY-S (VTM091) DXX2616

DDD1535- DDD1491- JA2401

SLOTIN MECHA ASSY

09SD PICK UP ASSY

DDD1527- Same Face 3 PWR_XON

B SLMB ASSY ZWNN1007G28-9-06A

Therefore, when replacing, be sure to use parts of identical designation.

KSW2 ASSY N SLD2 ASSY

Vertical DDD1521- 2 ADIN

Jumper Wire VKN1273-A

4.2 SIGNAL BLOCK DIAGRAM

SPINDLE PICKUP ASSY

SRVBCLK,SRVBUS0-3, MAIN CPU

I KSW2 ASSY K JOGB ASSY

J JFLB ASSY TEMPO SLIDER

4.3 POWER SUPPLY BLOCK DIAGRAM

SPINDLE PICKUP ASSY

VREF V+3R3_S IC408