DV 757ai

ORDER NO.
RRV2668
DV-757Ai
DVD PLAYER
DV-757Ai
DV-S755Ai
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Regional restriction
Model Type Power Requirement Remarks
codes (Region No.)
DV-757Ai WYXJ AC220-240V 2

DV-S755Ai RLXJ/NC AC110-127V/220-240V 3
For details, refer to "Important symbols for good services".
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2002
T-ZZE SEPT. 2002 printed in Japan
1 2 3 4
SAFETY INFORMATION
A
This service manual is intended for qualified service technicians; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trainedto properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and
may void the warranty. If you are not qualified to perform the repair of this product properly and
safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING !
B
THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1
BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR
CLASS 1.
A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE APPARATUS.
LASER DIODE CHARACTERISTICS

FOR DVD : MAXIMUM OUTPUT POWER : 5 mW
WAVELENGTH : 650 nm
FOR CD : MAXIMUM OUTPUT POWER : 5 mW
WAVELENGTH : 780 nm
LABEL CHECK
Location: Printed on the Rear Panel
Additional Laser Caution

1. Loading-status detection switch (S101 on the LOAB assy) are detected
by the microprocessor (IC601 in the DVDM assy).
E To permit the laser diode to oscillate, it is required to set the loading-
status detection switch for the clamp position (the center terminal of
S101 is shorted to +3V).
When the voltage of IC101-pin 20 is +3V, IC601 (microprocessor)
-pin 83 is +3V and IC601-pin 84 is +3V, 650nm laser diode for DVD
oscillates in the DVDM Assy.
When the voltage of IC101-pin 20 is +3V, IC601 (microprocessor)
-pin 83 is 0V (GND) and IC601-pin 84 is +3V, 780nm laser diode for
CD oscillates in the DVDM Assy.
In the test mode * , the laser diode oscillates when microprocessor
detects a PLAY signal, or when the PLAY key is pressed (S104 ON in
the FLKY assy), with the above requirements satisfied.
2. When the cover is open, close viewing through the objective lens with
the naked eye will cause exposure to the laser beam.
F
: See page 70.
2 DV-757Ai
1 2 3 4
5 6 7 8
[ Important symbols for good services ]

In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.
When you find the procedures bearing any of the symbols, be sure to fulfill them:
A
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and
should keep the safety during servicing by following the safety instructions described in this manual.
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable.
In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning, B
proper cleaning should be performed to restore their performances.
4. Shipping mode and shipping screws

To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or
the shipping screws should be installed before shipping out in accordance with this manual, if necessary.
5. Lubricants, glues, and replacement parts

Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying
glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the
prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed
ones should be used.
C
DV-757Ai 3
5 6 7 8
1 2 3 4
CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SPECIFICATIONS ............................................................................................................................................ 5
A 2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 8
2.1 PACKING ................................................................................................................................................... 8
2.2 EXTERIOR SECTION.............................................................................................................................. 10
2.3 FRONT PANEL SECTION ....................................................................................................................... 12
2.4 LOADING MECHA ASSY ........................................................................................................................ 14
2.5 TRAVERSE MECHANISM ASSY-S ......................................................................................................... 16
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .......................................................................................... 18
3.1 BLOCK DIAGRAM ................................................................................................................................... 18
3.2 LOAB ASSY and OVERALL WIRING DIAGRAM..................................................................................... 22
3.3 DVDM ASSY 1/4 [FTS BLOCK] ............................................................................................................... 24
3.4 DVDM ASSY 2/4 [FR BLOCK] ................................................................................................................. 26
3.5 DVDM ASSY 3/4 [EBY/AV1 BLOCK] ....................................................................................................... 28
B
3.6 DVDM ASSY 4/4 [VENC BLOCK] ............................................................................................................ 30
3.7 JACB ASSY 1/2 [AUDIO BLOCK] ............................................................................................................ 32
3.8 JACB ASSY 2/2 [VIDEO BLOCK] ............................................................................................................ 34
3.9 SACDB ASSY .......................................................................................................................................... 36
3.10 FLKY, KEYB and MSWB ASSYS........................................................................................................... 38
3.11 SCRB ASSY [WYXJ Type Only]............................................................................................................. 40
3.12 ILKB ASSY............................................................................................................................................. 42
3.13 POWER SUPPLY UNIT.......................................................................................................................... 44
3.14 WAVEFORMS [DVDM ASSY] ................................................................................................................ 45
3.15 WAVEFORMS [JACB ASSY] ................................................................................................................. 46
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 47
C 4.1 LOAB ASSY ............................................................................................................................................. 47
4.2 DVDM ASSY ............................................................................................................................................ 48
4.3 JACB ASSY ............................................................................................................................................. 50
4.4 SACDB ASSY .......................................................................................................................................... 54
4.5 SCRB ASSY ............................................................................................................................................ 55
4.6 FLKY and KEYB ASSYS ......................................................................................................................... 56
4.7 POWER SUPPLY UNIT............................................................................................................................ 58
4.8 ILKB ASSY............................................................................................................................................... 59
4.9 MSWB ASSY ........................................................................................................................................... 60
5. PCB PARTS LIST ........................................................................................................................................... 61
6. ADJUSTMENT ............................................................................................................................................... 68
6.1 ADJUSTMENT ITEMS AND LOCATION ................................................................................................. 68
D 6.2 JIGS AND MEASURING INSTRUMENTS............................................................................................... 68
6.3 NECESSARY ADJUSTMENT POINTS ................................................................................................... 69
6.4 TEST MODE ............................................................................................................................................ 70
6.5 MECHANISM ADJUSTMENT .................................................................................................................. 71
7. GENERAL INFORMATION ............................................................................................................................. 74
7.1 DIAGNOSIS ............................................................................................................................................. 74
7.1.1 ID NUMBER AND ID DATA SETTTING ................................................................................................ 74
7.1.2 SELF-DIAGNOSIS FUNCTION OF PICKUP DEFECTIVE................................................................... 76
7.1.3 TEST MODE SCREEN DISPLAY ......................................................................................................... 77
7.1.4 SELF-DIAGNOSIS FUNCTION ............................................................................................................ 79
7.1.5 FUNCTION SPECIFICATION OF THE SERVICE MODE ..................................................................... 80
7.1.6 ERROR DISPLAY ................................................................................................................................. 81
E 7.1.7 TEST POINTS LOCATION & WAVEFORMS ........................................................................................ 84
7.1.8 TROUBLE SHOOTING ......................................................................................................................... 86
7.1.9 DISASSEMBLY ..................................................................................................................................... 88
7.2 IC ............................................................................................................................................................. 97
7.3 DISC / CONTENT FORMAT PLAYBACK COMPATIBILITY ................................................................... 152
7.4 CLEANING............................................................................................................................................. 153
8. PANEL FACILITIES ...................................................................................................................................... 154
4 DV-757Ai
1 2 3 4
5 6 7 8
1. SPECIFICATIONS
7 DV-757Ai/WYXJ
A
Manufactured under license from Dolby

Laboratories. Dolby and the double-D
symbol are trademarks of Dolby Laboratories.
DTS is a registered trademark of Digital
Theater Systems, Inc.

TruSurround and the symbol are
trademarks of SRS Labs, Inc. TruSurround
technology is incorporated under license from F
SRS Labs, Inc.
DV-757Ai 5
5 6 7 8
1 2 3 4
7 DV-S755Ai/RLXJ/NC
Manufactured under license from Dolby

Laboratories. Dolby and the double-D
symbol are trademarks of Dolby Laboratories.
DTS is a registered trademark of Digital
Theater Systems, Inc.

TruSurround and the symbol are
trademarks of SRS Labs, Inc. TruSurround
technology is incorporated under license from
SRS Labs, Inc.
F
6 DV-757Ai
1 2 3 4
5 6 7 8
DV-757Ai 7
5 6 7 8
1 2 3 4
2. EXPLODED VIEWS AND PARTS LIST

NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
A The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
2.1 PACKING
1
B
5
WYXJ Type Only
10 2
8
3
10
4
1519
"Operating Instructions" 6
7
C
14
11 12
Front side
13
8 DV-757Ai
1 2 3 4
5 6 7 8
PACKING parts List

Mark No. Description Part No. Mark No. Description Part No.
> 1 Power Cable See Contrast table (2) 13 Packing Case See Contrast table (2)
14 Mirror Mat Sheet VHL1068 A
2 Stereo Audio Cable (L = 1.5m) VDE1052
3 Video Cable (L = 1.5m) VDE1053 15 Operating Instructions See Contrast table (2)
4 4-pin S400 i.LINK Cable VDE1076 (English / Spanish)
(L = 1.5m)
NSP 5 AA/R6P Dry Cell Battery VEM1031 16 Operating Instructions See Contrast table (2)
(French / German)
6 Remote Control See Contrast table (2) 17 Operating Instructions See Contrast table (2)
7 Battery Cover See Contrast table (2) (Italian / Dutch)
NSP 8 Warranty Card See Contrast table (2) 18 Operating Instructions See Contrast table (2)
9 (English)
10 Polyethylene Bag VHL1051 19 Operating Instructions See Contrast table (2)
B
(Trad-Chinese)
11 Pad F VHA1311
12 Pad R VHA1312
(2) CONTRAST TABLE

DV-757Ai/WYXJ and DV-S755Ai/RLXJ/NC are constructed the same except for the following:
DV-S755Ai/
Mark No. Symbol and Description DV-757Ai/WYXJ
RLXJ/NC
> 1 Power Cable ADG7053 ADG1154
6 Remote Control VXX2836 VXX2837
7 Battery Cover VNK4936 VNK4422
C
NSP 8 Warranty Card ARY7022 Not used
13 Packing Case VHG2248 VHG2250
15 Operating Instructions VRD1173 Not used

(English / Spanish)
(French / German)
(Italian / Dutch)
18 Operating Instructions Not used VRB1309
(English)
19 Operating Instructions Not used VRC1170
(Trad-Chinese) D
DV-757Ai 9
5 6 7 8
1 2 3 4
2.2 EXTERIOR SECTION

NON-CONTACT 49
A SIDE
48
CONTACT SIDE
57
Refer to "2.4 LOADING MECHA ASSY".

62
26
55
No.7, No.15:
WYXJ Type Only
11
B *1: Be just connected.
No.8 (AC Inlet Assy) CN1
C
D No.22 (Housing Assy) CN2
B
A
56 59 WYXJ Type Only
56
25 22*1
H7 57
40 23 10 15
41 8*1
63
61 54
E
54
55
51
61 G F 55
37 6 12 52
C 54 31
30 28 29
38 55
28 54 G
13
E
35
D F
G 54
B C 29 H
19
54 A 27 54
61 M
M 54
61 53
54 33 N
O
54 B J
J 1
H
24
53
3 18
2 53 I
J
53 I
C I
16 5
D 45 17 54 4
54 L
54 K D
39
44 53 53 60
50 43
N
54 37
O
20 36
58 9
46 21
E L
K 42
47 32 54
14 42
55 54
Refer to "2.3 FRONT PANEL SECTION".
34
F
55
10 DV-757Ai
1 2 3 4
5 6 7 8
EXTERIOR SECTION parts List

1 DVDM Assy See Contrast table (2) 33 Wire Saddle VEC2310
NSP 34 Bottom Plate VNA2469 A
2 MSWB Assy VWG2390
3 JACB Assy See Contrast table (2) 35 Rear Panel See Contrast table (2)
4 SACDB Assy VWG2353
5 ILKB Assy VWG2391 NSP 36 Base Chassis VNA2521
37 MH Spacer 2 VEC2319
> 6 POWER SUPPLY Unit VWR1361 38 Mechanism Holder VNE2266
7 SCRB Assy See Contrast table (2) NSP 39 PCB Base VNE2276
> 8 AC Inlet Assy See Contrast table (2) 40 Adapter 27L VNL1926
NSP 9 Earth Lead Unit VDA1903
10 Connector Assy PF13PP-D25 41 Adapter 27R VNL1927
42 Insulator VXA2424
B
11 Connector Assy PG05KK-E30 43 PCB Holder VNE2280
12 FFC (30P, JACB) VDA1905 44 PCB Holder 2 VNE2283
13 FFC (21P, JACB) VDA1906 NSP 45 Power Key 2 See Contrast table (2)
14 FFC (17P, FLKB) VDA1907
15 FFC (19P, SCRB) See Contrast table (2) 46 Tray Panel See Contrast table (2)
47 Door See Contrast table (2)
16 FFC (20P, DSP) VDA1909 48 Bonnet S See Contrast table (2)
17 FFC (40P, SACD) VDA1910 49 Label VRW1872
18 FFC (13P, ILKB) VDA1912 NSP 50 Cord with Plug DE012VF0
19 FFC (24P, ILKB) VDA1924
20 F Cushion VEB1348 51 F Cushion 2 VEB1350
C
52 Screw BBZ26P060FZK
21 Gasket (6.4X9.5) VEC2322 53 Screw BBZ30P060FCC
> NSP 22 Housing Assy VKP2278 54 Screw BBZ30P060FMC
23 Ferrite Core VTH1044 55 Screw BBZ30P080FZK
24 Ferrite Core VTH1045
NSP 25 Binder ZCA-BK1 56 Screw BBZ30P180FMC
57 Screw BCZ40P060FNI
NSP 26 LOADING MECHA Assy VWT1203 58 Screw BPZ30P100FMC
NSP 27 PCB Spacer (3X6) AEC7156 59 Screw See Contrast table (2)
28 Mini Clamp AEC7373 60 Screw IBZ30P080FCC
NSP 29 PCB Support REC1285 D
30 PCB Support VEC2184 61 Screw PPZ30P080FMC
62 Screw Z39-019
31 PCB Holder See Contrast table (2) NSP 63 ID Label VRW1877
32 PCB Holder VEC2283
(2) CONTRAST TABLE

DV-S755Ai/
RLXJ/NC
1 DVDM Assy VWS1540 VWS1534
3 JACB Assy VWV1917 VWV1919 E
7 SCRB Assy VWV1922 Not used
> 8 AC Inlet Assy ADX7406 VKP2268
15 FFC (19P, SCRB) VDA1908 Not used
31 PCB Holder VEC2215 Not used

35 Rear Panel VNA2490 VNA2492
NSP 45 Power Key 2 VNK5103 VNK5104
46 Tray Panel VNK5085 VNK5074
47 Door VEC2278 VEC2300
48 Bonnet Case S VXX2847 VXX2848

59 Screw CBZ30P080FZK Not used F
DV-757Ai 11
5 6 7 8
1 2 3 4
2.3 FRONT PANEL SECTION
A
9
9
F
2
9
10
9
1
B
E
6
9
8 (1/2)
11
8 (2/2)
5
D
NON-CONTACT
SIDE
E
CONTACT SIDE
12 DV-757Ai
1 2 3 4
5 6 7 8
FRONT PANEL SECTION parts List

1 FLKY Assy See Contrast table (2) 7 FL Lens See Contrast table (2)
8 Front Panel Assy See Contrast table (2) A
2 KEYB Assy VWG2369
3 FFC (17P, FLKB) VDA1907 9 Screw BBZ30P080FZK
4 Aluminum Panel See Contrast table (2) 10 Connector Assy PF02PP2R07
5 Pioneer Badge See Contrast table (2)
NSP 11 LED Lens 2 VNK5105
6 FL Filter VEC2281
(2) CONTRAST TABLE

DV-S755Ai/
RLXJ/NC
B
1 FLKY Assy VWG2358 VWG2360
4 Aluminum Panel VAH1394 VAH1403
5 Pioneer Badge VAM1124 PAN1377
7 FL Lens VEC2296 VEC2317
8 Front Panel Assy VXA2522 VXA2524
DV-757Ai 13
5 6 7 8
1 2 3 4
2.4 LOADING MECHA ASSY
Note : 8 To
6 DVDM
A
Refer to CN101
" Application of Lubricant".

8
8
To DVDM
CN114
Daifree To DVDM
GEM1036 CN115 2
8 Refer to
"2.5 TRAVERSE MECHANISM
ASSY-S".
12
Lubricating Oil 18 20
3
GYA1001
13
23 A 22
17
4 5
16
22 19
C
21
15
22
7 A
10
14
11
Lubricating Oil
D GYA1001
1
9 A
22
LOADING MECHA ASSY parts List
NSP 1 LOAB Assy VWG2346 16 Drive Gear VNL1923

2 Traverse Mechanism Assy-S VXX2858 17 SW Lever VNL1925
3 Loading Motor Assy VXX2505 18 Clamper Plate VNE2251
4 Motor Pulley PNW1634 19 Bridge VNE2252
E 5 Carriage DC Motor / 0.3W PXM1027 20 Clamper VNL1924
6 Flexible Cable (26P) VDA1864 21 Screw JGZ17P028FMC

7 Connector Assy 2P VKP2253 22 Screw Z39-019
8 Float Rubber VEB1327 23 Tray VNL1920
9 Belt VEB1330
10 Stabilizer VNE2253
11 Loading Base VNL1917

12 Float Base DVD VNL1918
13 Drive Cam VNL1919
F
14 Gear Pulley VNL1921
15 Loading Gear VNL1922
14 DV-757Ai
1 2 3 4
5 6 7 8
Application of Lubricant
A
Lubricating Oil
GYA1001
Around the shaft
No. 11
Loading Base
Lubricating Oil
GYA1001
Lubricating Oil
No. 13 Lubricating Oil GYA1001
Drive Cam GYA1001
No. 13
Rear View Top View Drive Cam
Inner side of a ditch Inner side of a ditch
Lubricating Oil Lubricating Oil
GYA1001 GYA1001
D
No. 23 Daifree No. 23 Daifree
Tray GEM1036 Tray GEM1036
Concave of unevenness Concave of unevenness
Inner side of a ditch

E
Daifree
GEM1036
Top View Bottom View

Side of the rib
Concave of unevenness
Daifree
Daifree GEM1036
GEM1036
DV-757Ai 15
5 6 7 8
1 2 3 4
2.5 TRAVERSE MECHANISM ASSY-S
17 (Torque : 0.12 0.01 Nm)
Silicone Adhesive
12 GEM1037
8
3
18
10 18
B
18
10 7
14
9
1
6
19
C Silicone Adhesive
GEM1037
13 4 (Adjustment Screw)
16 17 (Torque : 0.12 0.01 Nm)
To
DVDM
CN111
5 15
Screw Tight
D Silicone Adhesive
5 GYL1001
GEM1037
To DVDM
CN115 17 (Torque : 0.12 0.01 Nm)
16
2
E To DVDM
CN114
NON-CONTACT
SIDE
11
CONTACT SIDE
16 DV-757Ai
1 2 3 4
5 6 7 8
TRAVERSE MECHANISM ASSY-S parts List

Mark No. Description Part No.
1 Spindle Motor VXM1088
A
2 Stepping Motor VXM1090
> 3 Pickup Assy-S OXX8004
4 Skew Screw VBA1080
5 Skew Spring VBH1335
6 Guide Bar VLL1514

7 Sub Guide Bar VLL1515
8 Hold Spring VNC1017
9 Joint Spring VNC1019
10 Support Spring VNC1020
B
NSP 11 Mechanism Chassis VNE2248
12 Slider VNL1811
13 Spacer VNL1913
14 Joint VNL1914
15 FFC Holder VNL1915
16 Screw BBZ20P050FZK
17 Tapping Screw OBA8009
18 Screw PMA26P100FMC
19 Damper Sheet VEB1335
DV-757Ai 17
5 6 7 8
1 2 3 4
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM

3.1 BLOCK DIAGRAM
A
7 SIGNAL ROUTE
i.LINK
JA1 I ILKB ASSY
DSD_LFE
DSD_RS
DSD_LS
DSD_C
DSD_R
DSD_L
JA2
8 12 14 16 6 10
CN902
(19P)
DSD_LFE
DSD_RS
D SACDB ASSY
DSD_LS
DSD_C
DSD_R
DSD_L
33, 34, 25, 26, IC301
36, 37 29, 30 SACD_DA, TC74VHC541FT
SDO2
SACD_D0 6
158 12 2 62 DSDA, DSD0-DSD5 64 74 71 69 66 76
B IC201 -SACD_D5
78, 79, 81, 82 5
SDO1
TSB43CA43GGW 159 I I II
84, 85, 87 IC901 SDO0
IEEE1394 163 18 8 128 CXD2753R 4
PHY LINK I IC902 SACD Decoder DATA0A
IC101 167 CN102 CN903 10
PD5787A HY57V161610DTC-8 126
(13P) (13P) 16M SDRAM 169-176 IC801
HOST CPU XCA56367PV150
11-14 BD0-BD7
DVD-Audio
RFSACD
DSP
24 8-12, 35-37 CN901
(40P)
CN101 21-24
(24P) RFSACD BD0-BD7
17 4-6, 29-33
CN531
(40P)
IC211 AO00,
B DVDM ASSY TK15404M 27M 22/24AV1

DATA1A0
RFSACD DATA2A0
3 2 106 172 AOD0
164,
CN111
CLKIN
ACLKI
166-168
(26P) (26P)
SPINDLE OEIC AO00
RF- AO0 164
MOTOR 13 14 1 RFN Q106
C 11
RF+
16 3 RFP RFO 60
RFO AIN
172 AIN 13,14, DOUT0
IC701 201-208 DOUT0 170
20
B1
7 5 PD2 BHMIX 49
BH
185 CDDT PE5286A 19-24 BD0-BD7
B2 IC101 PH DVD Decoder 184-186,
21 6 4 PD1 LA9704W BH 52 36M 4 DMCK EBY-CHIP 188-192
DSPRF
B3 RF IC FE PD0-PD7
15 12 7 PD4 FE 41 CDDATA
B4 33M 5 DMACKI ADATA0 194 163 CDDIN
TE
16 11 6 PD3 TE 42
PICKUP 16M 169
32 33 30 31 39 3 IC751
ASSY M65776AFP
T DRV
25 2 12 VM4+
TE
FE
RF PH
RF BH
EFMIN
ROMXA
MPEG2 Decoder
T RTN AV-1
24 3 13 VM4- IC351
F DRV IN3- 3 47 FDO IC741
23 4 9 VM3- M56788AFP
F RTN FTS Driver IN4- 20 HY57V16160DTC-8
26 1 10 VM3+ 48 TDO IC201 16M SDRAM
LC78652W
SPDO
VM1+
VM2+
VM5+
28
VM1-
VM2-
VM5-
Servo DSP
XIN
CN114 37 IC781
(4P) M2V64S40DTP-7
35 34 31 32 15 14 46 14 64M SDRAM
ST1+
SPDO
STEPPING 2
MOTOR M ST1- 16M IC601 IC603
1 PD6345A VYW2045
D ST2+ System 16M Flash Memory
3
ST2- ST2 Control CPU
4 48
AN7
PK4
ST1
47
CN115
(12P) 21
57 105 (For IC201,IC701)
(For IC751)
(For IC701)
(For IC751)
(For IC701)
4-9 9-14
22/24AV1
4448
A LOAB ASSY IC251

27M
16M
36M
33M
BA6664FM
Spindle Driver
LOADING CN601 CN103 14 3 13 9 10 15

(5P) (5P)
FSEL1
CLK27M
CLK16M
36M
22/24M
CLK33M
MOTOR
ASSY LOAD-
2 1 1
+ LOAD+
M 1
3.3V
2 2
IC481
SW2 LOD POS
CN602 4 4 SM8707HV
SEL IR
(2P)
5 SW1(GNDS)
5 Clock Generator
IR
E S101
2 9 CN402
(17P)
Remote
V101 Sensor
VAW1073 Unit
F KEYB ASSY E FL TUBE
SEL IR
FLKY ASSY IR101 2
IR
9
IC101 17
KEY0 PE5314B
4 4 22 FL Control
KEY1
CN201 CN102 21
(4P) (4P)
CN101
(17P)
18 DV-757Ai
1 2 3 4
5 6 7 8
CN102
C JACB ASSY IC301 IC302
PCM1738EG-3 NJM5532MD IC304
(19P) 2 NJM5532MD JA301
IC201 26 1 2
DSD_R TC74VHC157F 3 1
14 3 L
AUDIO OUT
AUDIO_L
DSD_L DSD_L DSD_L
12
8 13 12 5 6 (2 ch)
DSD_LS
25 7 R
8 DATA0 5
14 20
DSD_LFE L
6 FRONT
DSD_C R
4
DSD_RS
CN502 10
IC401
(20P)
DSD1702EG IC402
DATA2
18 4 DSD_LS NJM5532MD JA302
DATA1 1 5
17 3 DATA2 9 7 B
DATA0B 4 6 L
19 2 SURROUND
AO0 R
6 15
5
9
AUDIO OUT
CN801 1
DSD_C
1 7
CENTER
6
(5.1 ch)
(20P)
CN701 24 DSD_LFE
2
(24P) 2
1 IC552 DATA1 1 SUB
4 3 WOOFER
I PD0274A 10 IC502
4 NJM5532MD
IC501
DSD1702EG
IC786
TC74VHC541FT 1
2 5
2, 3, 13, 14, CN551 (1/2) CN101 (1/2) JA602
AUDIO OUT
6, 7 17, 18 IC553 (21P) (21P) OPTICAL
DIGITAL
AO00 AO0 TC7WH157FU DATA0 DATA0
7 13 11 11
Q601 JA601
DOUT0 DOUT DOUT C
14 14 COAXIAL
IC902
27-34 PM0033A
PD0-PD7 PROGRESSIVE DATA2 DATA2
& HI-QUALITY 4 4
PC0-PC7 IC701
PB0-PB9
Video LA73054 JA703
Encoder DATA1 DATA1
PPD0-PPD7 2 2 Video Driver Amp.
1
Q932 VIDEO OUT
V V V V
44 15 15 2 33 2
V
Q933
Y Y Y Y
43 19 19 8 28 JA705
Y
Q934
C C C C 1
42 17 17 6 31
C
IC831 S VIDEO
ADV7300AKST Q936 OUT
12BIT Y/G YOUT Y/G/P_Y
Video 39 21 21 11 25 2
Encoder
D
COMPONENT
CB/B CBOUT CB/B/P_CB Y
VIDEO OUT
38 23 23 14 23 Y (GREEN)
G
Q939 CB
PB (BLUE)
Q938
B
CR/R CROUT CR/R/P_CR CR
37 25 25 16 21 PR (RED)
R
CN901 CN701 JA702
(30P) (30P)
CN551 (2/2) CN101 (2/2) Y

(21P) (21P)
D1/D2
SEL IR JA801 CB
RY701
RY702
SEL IR VIDEO OUT
CONTROL
16 16
IN
CR
AUDIO_L
IR IR
18 18 OUT CN703
JA802 G
C
R
V
Y
B
RLXJ/NC Only
18 10 6 8 1 4 2 CN702
(19P)
E
JA901
AUDIO_L
2
H SCRB ASSY AUDIO_L
RY902
3
6
L OUT
L IN
V
10 7 B
Y IC901 4 3 2 4 3 2
14 MM1505XN 11 G OUT
C C RY903
12 6 R/C
15 R/C
R
R 2
19 4 7 8 9 7 8 9 19 V/Y OUT
G
16 20 V IN
B IC902
18 MM1507XN AV CONNECTOR
Y
CN901 6 Y/V JA902 (RGB) - TV
(19P) V 2
4 3 L OUT
4 3 2 4 3 2
6 L IN
IC903
MM1507XN 7 B IN
11 G IN
F
6 V 7 8 9 7 8 9 IN
V 2 RY904 15 R/C IN
4
19 V OUT
G RY905
B 20 V IN
WYXJ Only
DV-757Ai 19
5 6 7 8
1 2 3 4
7 POWER SUPPLY BLOCK

A
C JACB ASSY
IC102 IC101 IC702
V+5A NJM78M05FA V+8A NJM78M08FA V+12V PQ05RD11 V+5V V+12V V+5V V+5V V+12V V+11V
EV+6 19 1
V+5D V+3D D921
12 8
CN101 CN701 CN702 CN901
(21P) (30P) (19P) (19P)
12 17 19 8 9 11 13
CN551
(21P)
12 17 19 8 9 11 13
CN901
(30P)
H SCRB ASSY
WYXJ Only
V+5D V+3D V+12 V+6EV
B
D SACDB ASSY
V+3D
(SACD) V+3D
26 15
27 14
28 13
V18_ADSP1
V18D
V+3_18REG
V+3D
29
30
12
11 I ILKB ASSY
31 10
32 9 V+3D
IC808 V+5D V+3D
MM1561JF 33 8 V+5D
1.8V REG. 21 4
CN901 CN531 22 3
C (40P) (40P)
24 1
V+3DSD V+3IO V+3_SD V+3V_ADSP1
CN701 CN101
(24P) (24P)
V+2C
V+3D V+3D
(SACD) (DVDAUDIO)
V+25V IC906 V+3D V+3D
(SACD) 2 19
CN801 CN502
(20P) (20P)
IC402 SW+5 V+5S V+5D

A LOAB ASSY MM1565AF
5V REG
V+3D CN601 CN103

(5P) (5P)
D IC791 V18D
3 3 V+3D MM1561JF
1.8V REG
CN115 V+25V
(12P)
SPINDLE 11 V+5S
MOTOR IC403 V+25V
PQ025EZ01
2.5V REG
CN111
(26P)
PICKUP
ASSY-S
8 19 V+5S
IC404
V33EV F KEYB ASSY
MM1385EN
S302 V+3E
MSWB
E J ASSY CN302
9
CN201
(9P)
(2P)
1 9
CN102
V+6M V+6EV V12M V+12 EV+4V V3VD V+3D (9P)
1 V+3E
CN401
G POWER
SUPPLY
CN2
(2P)
1
EV6V (B)
1
(13P)
V+12 V33EV
14 14
V+3E V+12
EV6V (A)
UNIT 2
-28V
2
-28V
16 16
IC101
3 3 3 3
FLDC+ FLDC+
4 4 7 7
CN1 FLDC- FLDC-
LIVE 5 5 5 5
SW+12V
9 9
F1 EV+4V
CN402 CN101
AC IN 11 11 (17P) (17P) V101
FL TUBE
SW+3.3
F NEUTRAL
13 13
CN101
(13P)
B DVDM ASSY E FLKY ASSY

20 DV-757Ai
1 2 3 4
5 6 7 8
DV-757Ai 21
5 6 7 8
1 2 3 4
3.2 LOAB ASSY and OVERALL WIRING DIAGRAM
D SACDB ASSY
(VWG2353)
D
C JACB ASSY
(WYXJ : VWV1917)
(RLXJ/NC : VWV1919)
RLXJ/NC Only
F
H SCRB ASSY
(VWV1922)
Note : When ordering service parts, be sure
to refer to "EXPLODED VIEWS and
PARTS LIST" or "PCB PARTS LIST".
WYXJ Only
22 DV-757Ai
1 2 3 4
5 6 7 8
KEYB ASSY
I ILKB ASSY F (VWG2369)
(VWG2391)
E FLKY ASSY
(WYXJ : VWG2358)
(RLXJ/NC : VWG2360) B
J
MSWB ASSY
(VWG2390)
C
G
POWER SUPPLY UNIT
(VWR1361)
PICKUP ASSY-S
(OXX8004)
D
B DVDM ASSY
(WYXJ : VWS1540)
(RLXJ/NC : VWS1534)
E
SPINDLE
MOTOR
: VXM1088
STEPPING MOTOR
: VXM1090
LOADING
MOTOR ASSY F
LOAB ASSY
A (VWG2346)
: VXX2505
A
DV-757Ai 23
5 6 7 8
1 2 3 4
3.3 DVDM ASSY 1/4 [FTS BLOCK]

(RF)
: RF SIGNAL ROUTE
A
B 1/4
DVDM ASSY (RF_V)
(RF_A)
: RF (VIDEO) SIGNAL ROUTE
(WYXJ : VWS1540) : RF (AUDIO) SIGNAL ROUTE

(AD)
(RLXJ/NC : VWS1534) : AUDIO DATA SIGNAL ROUTE
(F)
: FOCUS SERVO LOOP LINE
(T)
: TRACKING SERVO LOOP LINE Buffer (RF)
(S)
: STEPPING SERVO LOOP LINE
Buffer (RF)
(RF_V)
(RF_A)
(RF)
B
Buffer (RF)
1
(RF)
(T) 4
(F)
C B 2/4
LD Driver
for DVD
B 2/4
LD Driver SW for
for CD Defect Signal
D
PICKUP ASSY
(RF)
(F)
(F) B 2/4
(T)
(T)
(F)
(S)
(F)
(T) B 2/4
(T)
(F)
A Focus, Tracking
CN601 and Loading Driver
SPINDLE
(T)(T)
MOTOR
STEPPING
MOTOR
(S)
(S) (F) (F)
F (S)
(S)
(F)
B 2/4
(T)
B 1/4
24 DV-757Ai
1 2 3 4
5 6 7 8
B 2/4 A
B 3/4
(RF_V) VCO Circuit

(RF_V)
B 3/4
B
B 2/4
B 3/4 RF Amp.
(RF for SACD Water
Mark detection)
B 3/4
B 2/4
C
B 2/4
(AD)
(T)
(F)
(RF_A)
5 D
(F)
(T)
B 2/4
E
8 9
B 3/4
7
10 11
Spindle Driver
B 3/4 B 3/4
B 1/4
DV-757Ai 25
5 6 7 8
1 2 3 4
3.4 DVDM ASSY 2/4 [FR BLOCK]
B 2/4 DVDM ASSY

(WYXJ : VWS1540)
(RLXJ/NC : VWS1534)
B
PGM 16M FLASH MEMORY
B 3/4
B 1/4 B 1/4 B 3/4
B 3/4 B 3/4
B 3/4
B 3/4
C
B 1/4
B 4/4
B 1/4
B 4/4
B 1/4
B 4/4
D B 1/4
FR CPU
B 1/4
B 1/4
B 3/4
B 1/4 B 1/4
R699
XMRST
0
B 4/4
B 4/4 B 1/4
F
B 4/4
B 3/4
B 2/4 B 4/4
26 DV-757Ai
1 2 3 4
5 6 7 8
B 3/4 Clock Signals: Refer to "7.1.7 TEST POINT LOCATION A

& WAVEFORMS"
B 4/4
WY: L4930(VTL1074)
RL: R493(47)
B 3/4
WY: L4820(VTL1074)
RL: R482(47)
B 3/4
B
B 3/4
B 1/4
B 4/4
B 3/4
B 3/4
C
3.3V Regulator
I
CN101
G CN101
D
B 1/4
B 3/4
CN101
E
D
B 1/4 CN901
E
C749
1
WY Only
B 3/4
XMRST
F
: The power supply is shown with the marked box.
B 2/4
DV-757Ai 27
5 6 7 8
1 2 3 4
3.5 DVDM ASSY 3/4 [EBY/AV1 BLOCK]
B 3/4 DVDM ASSY

(WYXJ : VWS1540)
(RLXJ/NC : VWS1534)
B
B 2/4
B 2/4
C
B 2/4
(VD)
(AD)
B 1/4
(D)
(D)
B 2/4
(AD) (AD)
D
B 1/4
DVD data Decoder (RF_V) (RF_V)
E
B 2/4
B 1/4
B 2/4
B 1/4
F
B 4/4 B 1/4
B 1/4
B 3/4
28 DV-757Ai
1 2 3 4
5 6 7 8
: The power supply is shown with the marked box. A
B 1/4 (D) (D)
B 4/4 B 2/4
B
B 2/4 B 4/4
(D) (D)
(VD)
(AD)
(VD)
C
(D)
(D)
D
MPEG, DVD-Audio, DTS Decoder
and
Progressive scan Processer
B 2/4
(RF_V)
: RF (VIDEO) SIGNAL ROUTE
(VD)
: VIDEO DATA SIGNAL ROUTE
(AD)
: AUDIO DATA SIGNAL ROUTE
(D)
: AUDIO (DIGITAL) SIGNAL ROUTE
(P_Y)
: PROGRESSIVE SCAN VIDEO SIGNAL ROUTE [Y]
(P_Pb)
: PROGRESSIVE SCAN VIDEO SIGNAL ROUTE [Pb] F
(P_Pr)
: PROGRESSIVE SCAN VIDEO SIGNAL ROUTE [Pr]
B 3/4
DV-757Ai 29
5 6 7 8
1 2 3 4
3.6 DVDM ASSY 4/4 [VENC BLOCK]
(VD)
(VD)
100
(VD)
(VD)
C
(VD)
B 3/4
D (V)
(VD)
(Y)
(C)
(VD)
(Y/P_Y/G)
B 4/4 DVDM ASSY

(WYXJ : VWS1540) (Pr/P_Pr/R)
(RLXJ/NC : VWS1534)
(Pb/P_Pb/B)
F
B 4/4
30 DV-757Ai
1 2 3 4
5 6 7 8
(R) (VD) (Pr)

: R SIGNAL ROUTE : VIDEO DATA SIGNAL ROUTE : Pr SIGNAL ROUTE
(G) (V) (P_Y) A
B 3/4 (B)
: G SIGNAL ROUTE
(Y)
: V SIGNAL ROUTE
(P_Pb)
: B SIGNAL ROUTE : Y SIGNAL ROUTE : PROGRESSIVE SCAN VIDEO SIGNAL ROUTE [Pb]
(C) (P_Pr)
: C SIGNAL ROUTE : PROGRESSIVE SCAN VIDEO SIGNAL ROUTE [Pr]
(Pb) (D)
: Pb SIGNAL ROUTE : AUDIO (DIGITAL) SIGNAL ROUTE
B 3/4
(D) (D)
B 3/4 B
(D)
(D)
B 2/4
B 2/4
(D)
B 2/4
(D)
(D) (D)
WY: VTL1108(L5700) C570 C
(D)
B 3/4 RL: 22 15p WY
Only
(D) B 2/4
B 2/4
D
CN801 B 2/4
C 1/2
CN101
B 2/4
Buffer
C 2/2
(V)
CN701 D
B 2/4
14
(Y) 13 17 20
(Pr/P_Pr/R)
12
Buffer (Pb/P_Pb/B)
(Y/P_Y/G) 16 19
Buffer
15 18 (Y)
(C)
(C)
E
(V)
Buffer
(Y/P_Y/G) B 3/4
B 2/4
Buffer
(Pr/P_Pr/R) (D)
(D)
Buffer
F
(Pb/P_Pb/B)
B 3/4
B 4/4
DV-757Ai 31
5 6 7 8
1 2 3 4
3.7 JACB ASSY 1/2 [AUDIO BLOCK]
A D C 1/2 JACB ASSY

CN902
(WYXJ : VWV1917)
(RLXJ/NC : VWV1919)
SW for Audio Digital data select
of SACD or others (3 lines)
Audio DAC
for Front channel
(2 ch)
21 22
(D)
B (D)
(D)
24 23
(D)
(D)
+8V Regulator
C (D)
(D)
+5V Regulator
(D)
DIGITAL AUDIO OUT (D)

COAXIAL
D B 4/4
CN551
R605
WY: 82
RL: 68
DIGITAL AUDIO OUT
OPTICAL Audio DAC
for Ls, Rs
(D)
(2 ch)
C 2/2 (D)
(D)
(D)
(D)
Audio DAC
for C, LFE (Sub Woofer)
F (2 ch)
C 1/2
32 DV-757Ai
1 2 3 4
5 6 7 8
(D)
A
SW : AUDIO SIGNAL ROUTE
C 2/2
for Mute Control Signal
Q350- Q352, Q360- Q362:

Mute SW
25
R/FR ch. B
Differential Amp.
(with LPF) L/FL ch.
FR ch.
FL ch.
IC302, IC303:
I to V change
circuit
Audio out
SW (Front 2ch/Down mixed stereo)
for Mute Control
Signal
SW
for Mute Control
Signal Reference voltage
generation
for Audio Amp.
Q410, Q420, Q510, Q520:

Audio Amp. Mute SW
(with LPF)
Ls ch.
SW
for Mute Control Rs ch.
Signal
Center E
ch.
LFE ch.
(Sub
Woofer)
Audio out
F
SW Audio Amp.
(with LPF) : The power supply is shown with the marked box.
for Mute Control
Signal
LPF: Low Pass Filter C 1/2
DV-757Ai 33
5 6 7 8
1 2 3 4
3.8 JACB ASSY 2/2 [VIDEO BLOCK]
A
C 2/2 JACB ASSY
(WYXJ : VWV1917)
(RLXJ/NC : VWV1919)
(D)
C 1/2
(D)
(V)
(V)
B (C) (C)
(Y)
(Y)
B 4/4 (C)
(V)
(Y/P_Y/G)
(Y/G)
CN901
(Y) (Pb/P_Pb/B) (Pb/B)
(Y/P_Y/G) (Pr/P_Pr/R) (Pr/R)
(Pb/P_Pb/B)
(Pr/P_Pr/R)
(V)
: V SIGNAL ROUTE
(Y)
: Y SIGNAL ROUTE
(C)
: C SIGNAL ROUTE
(Pb)
: Pb SIGNAL ROUTE
(Pr)
: Pr SIGNAL ROUTE
(R)
: R SIGNAL ROUTE
(G)
: G SIGNAL ROUTE
(B)
E : B SIGNAL ROUTE
(D)
: AUDIO SIGNAL ROUTE
(P_Y)
(P_Pb)
: PROGRESSIVE SCAN VIDEO SIGNAL ROUTE [Pb]
(P_Pr)
: PROGRESSIVE SCAN VIDEO SIGNAL ROUTE [Pr]
C 2/2
34 DV-757Ai
1 2 3 4
5 6 7 8
Composite Video out

(V) (V)
(C) B
(Y)
(Y/G)
(Pb/B)
(Pr/R) (Y)
(C)
(Pr)
(Pb)
(Y)
(Y)
(C)
WYXJ Only Video out

(Pb/B)
(Pr/R)
C
(Y/G)
(Y)
(Pb)
(Pr)
Component Video out
D
(Y)
(Pb)
(Pr)
(G)
(R)
(B)
D1/D2 Video out

RLXJ/NC Only
WYXJ Only
E
C 1/2
(V) H
(C) CN901
(Y)
(G)
F
(B)
(R)
C 2/2
DV-757Ai 35
5 6 7 8
1 2 3 4
3.9 SACDB ASSY
D SACDB ASSY
A
(VWG2353)
(AD) (AD)
E
B 4/4 CN502
B 2/4
CN531
(AD) (AD)
D
36 DV-757Ai
1 2 3 4
5 6 7 8
(AD)
: AUDIO DATA SIGNAL ROUTE
(D)
R971- R979: VTL1074

(L971- L979)
B
CN102
(D)
I
C
(D)
D
(D)
(D)
(D)
(D)
19R-1.25FJ E
(AD)
(D)
(D)
(D)
(D)
TC7SHU04F
C 1/2 F
CN102
D
DV-757Ai 37
5 6 7 8
1 2 3 4
3.10 FLKY, KEYB and MSWB ASSYS
E
FLKY ASSY
(WYXJ : VWG2358)
F
(RLXJ/NC : VWG2360)
E
38 DV-757Ai
1 2 3 4
5 6 7 8
MSWB ASSY A
J (VWG2390) G
CN2
KEYB ASSY
F (VWG2369)
B 2/4
CN402
FLKY ASSY KEYB ASSY

S101 : 0 (OPEN/CLOSE) S201 : VIDEO OFF
S102 : 7 (STOP) S202 : PROGRESSIVE
S103 : 8 (PAUSE) S203 : POWER STANDBY/ON
S104 : 3 (PLAY)
S105 :
S106 : 4 1
: The power supply is shown with the marked box. F
E F J
DV-757Ai 39
5 6 7 8
1 2 3 4
3.11 SCRB ASSY [WYXJ Type Only]
A H SCRB ASSY
(VWV1922)
SW Buffer
(R)
(B)
(G)
Buffer
(C)
C C 2/2
CN702 SW
(Y)
(C)
(V)
(R)
(R/C)
D
Video Amp.
with SW
(B)
(B)
Video Amp.
with SW
(G)
(G)
(Y/V) (Y/V)
(V)
(V) (V)
Video Amp.
F
H
40 DV-757Ai
1 2 3 4
5 6 7 8
(V) (Y/V)
: V SIGNAL ROUTE : Y/V SIGNAL ROUTE A
(Y) (R/C)
: Y SIGNAL ROUTE : R/C SIGNAL ROUTE
(C) (R)
: C SIGNAL ROUTE : R SIGNAL ROUTE
(G)
: AUDIO SIGNAL ROUTE : G SIGNAL ROUTE
(B)
: B SIGNAL ROUTE
RY901-RY905: Relay SW
(B) (B)
(G) (G)
(R/C)
C
(Y/V)
(V)
(R/C) (B)
(R/C) (R/C)
(G) D
(R/C) (R/C)
(B)
(B)
(B) (V)
(V)
(G)
(G)
(G)
(Y/V) E
(Y/V)
(Y/V)
(Y/V)
(V)
(V) (V)
(V) (V)
F
H
DV-757Ai 41
5 6 7 8
1 2 3 4
3.12 ILKB ASSY

ILKB ASSY
A I (VWG2391)
(D)
(D)
(D)
B (D)
(D)
(D)
(D)
(D)
(D)
I
42 DV-757Ai
1 2 3 4
5 6 7 8
(D)
(D)
(D)
(D)
(D)
C
(D)
22
22
(D)
(D)
(D)
(D)
D
B 2/4
CN701
D
(D)
CN903
(D)
I
DV-757Ai 43
5 6 7 8
F
E
B
A
D
C
44
CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE.
G
G POWER SUPPLY UNIT (VWR1361) REPLACE ONLY WITH SAME TYPE NO. 491.800 MFD, BY
LITTELFUSE INC. FOR P101 (AEK7063).
NOTE OF SPARE PARTS IN POWER SUPPLY (SYPS) UNIT CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE.
1
1
In case of repairing, use the described parts only to prevent an accident. REPLACE ONLY WITH SAME TYPE NO. 49101.6 MFD, BY
Please write the red mark on the board when the primary section of POWER SUPPLY (SYPS) Unit is repaired.
Please take care to keep the space, not touching other parts when replacing the parts. CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE.
REPLACE ONLY WITH SAME TYPE NO. 491002 MFD, BY
CN2
J
CN302
P101 CN101
AEK7063
250V T2AH 800mA
SW+12V
9
F1
REK1101
3.13 POWER SUPPLY UNIT
2
2
2A P102
AEK7066
ASSY
1.6A
E+6V(B)
AC INLET
AEK7067 1
CN1 2.0A P104
E+6V(A)
2
SW+3.3V
13
P_CONT
DV-757Ai
7
P103
E+4V B 2/4
AEK7012 11
1.6A CN401
3
3
GND
6, 8, 10, 12
-28V
3
FLDC+
4
FLDC-
5
4
4
NOTE FOR FUSE REPLACEMENT

CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE.
CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 49101.6 MFD, BY
REPLACE WITH SAME TYPE AND RATINGS ONLY. LITTELFUSE INC. FOR P103 (AEK7012).
G
5 6 7 8
3.14 WAVEFORMS [DVDM ASSY]
Note : The encircled numbers denote measuring point in the schematic diagram. A
B DVDM ASSY
Measurement condition : No. 1 to 4 and 6 to 11 : MJK1, Title 1-chp 1 No. 12 to 14 : DVD-REF-A1, T2-Chap.1
No. 5 : CD, ABEX-784 Track 1 No. 15 to 20 : DVD-REF-A1, T2-Chap.19
IC101-pin 3 (RF) IC251 - pin 24 (FG) Foot of R963 (C) Foot of R958 (Pb)
1 V: 200mV/div. H: 0.1sec/div.
7 V: 1V/div. H: 5msec/div.
13 V: 0.2V/div. H: 10sec/div.
AC mode
GND
B
GND
Q106-emitter (RFO) Foot of R261 (FPWM) Foot of R960 (Y) Foot of R957 (Pr)
8 V: 1V/div. H: 10sec/div.
AC mode
GND
GND
Foot of R262 (VPWM) Foot of R959 (Y) C

3 9 V: 1V/div. H: 10sec/div.
GND
IC101-pin 42 (Tracking Error) Foot of R263 (PPWM) Foot of R958 (Pb)

4 (AI-Inner Tracking Off)
10 V: 1V/div. H: 0.2msec/div.
V: 500mV/div. H: 2msec/div.
AC mode
D
GND
GND
IC201 - pin 39 (EFM before slice) Foot of R264 (RPWM) Foot of R957 (Pr)
5 V: 0.5V/div. H: 0.2sec/div.
GND
E
GND
IC201 - pin 1 (EFM) Foot of R964 (V) Foot of R959 (Y)

6 V: 1V/div. H: 0.2sec/div. 12 V: 0.2V/div. H: 10sec/div.
GND
DV-757Ai 45
5 6 7 8
1 2 3 4
3.15 WAVEFORMS [JACB ASSY]
A Note : The encircled numbers denote measuring point in the schematic diagram.
C JACB ASSY
Measurement condition : No. 21 to 25 : DVD-REF-A1, T2-Chap.1
IC301-pin 4 (LRCK)
IC301-pin 5 (DATA0)
22 V: 1V/div. H: 500nsec/div.
C IC301-pin 6 (BCK)
IC301-pin 7 (PMCK)
IC302 - pin 1 (Analog OUT)

46 DV-757Ai
1 2 3 4
5 6 7 8
4. PCB CONNECTION DIAGRAM

4.1 LOAB ASSY
A
NOTE FOR PCB DIAGRAMS :

1. Part numbers in PCB diagrams match those in the schematic 3. The parts mounted on this PCB include all necessary parts for
diagrams. several destinations.
2. A comparison between the main parts of PCB and schematic For further information for respective destinations, be sure to
diagrams is shown below. check with the schematic diagram.
Symbol In PCB Symbol In Schematic 4. View point of PCB diagrams.
Part Name
Diagrams Diagrams
B C E B C E
Connector Capacitor
Transistor
B C E
B C E B C E SIDE A B
Transistor
B C E with resistor
D G S D G S
Field effect
D G S transistor
P.C.Board Chip Part SIDE B
Resistor array
3-terminal
regulator
C
SIDE A SIDE B
A LOAB ASSY
D
(VNP1836-B)
CN602 CN601 CN601 CN602

B CN103
M
LOADING
MOTOR
ASSY E
A A
DV-757Ai 47
5 6 7 8
4 3 2 1
DV-757Ai 48
B
E CN101 CN402 CN531 D CN901 CN502 D CN801
F
CONTACT SIDE
SIDE A
CONTACT SIDE CONTACT SIDE (SECOND)
R599
17 C533 1 1 19
19 DSP
17 1
CN502
1
1 39
39 R590 R592 C667
CN402
22 20
20 R598
R593
1
FL
C603
IC601
IC601
2 40 C604
R664
2 R667
C534
R410 40
R661
R418
R663
R408
C531
SACD CN531 44 1
KN1 45
HCT163
R534
R441 176 R619
R409
R413
C426
R414
C605
C532 R652 94V-0

R411
R540
R539
R412
R417
C666 R666
R676
R537 C658
R741
C657
R536
R535
R533
R531
VWS1531- VWS1535-
M
VWS1532- VWS1539-
R607 R635
R606 R605
R647 R602
C662
R662
R655
VWS1533- VWS15 - R641 C607

VWS1534- AWX8156-
R651
C745 C610 R668

R538
C613
R620
R669
R615
MOTOR
E
C615
R627
R611
R693
R623
R695
R640
R714 BAR CODE R633

SPINDLE
LDREAD
R696
R624
R694
C695
C693
88 133 C614 A
89 132
R268 C261
RPWM X601
R713
R272
PPWM R683
R229
C231
C265 8 C616
24 24
R706 C266 VPWM

C618
R629
C226
R223
C230
R681
1 R266 FPWM R622

R224 C227
R264 12V
R313
C391
R391
CONTACT SIDE
C201
R628
R631
R675 R263 C314

R762
IC261
R262
R638
R311
R637
R645
R630
R674
12
12
FG
IC261
CN115
R626
R261 C313
R673 R317 C223
4 5 R270
R672 R231
11
R704 R705
C233
R269 R271 R232 R280 C299

R701 C264 C263 A C224
R671 C315
CN105
R312
C R310 C236
M
R316
C701
30
29
CN115
R798 R314 100 76

C205
IC302 C711 1
R721 C225
1
IC302
R482
R487 R472
1
C474
R493 C486
C489 R497
R483 R471
4 1 C222 R222
75
SPDL
R221
R726
CN701
C312
1212
R301
R318
C203 C368
R725
1
C221
R724
6M
1
CN701 C799
CN104
iLINK
R201
R322
C485
MOTOR
GNDM
C702
5
C200
1
CONTACT SIDE
IC201
IC201 D
R488
C317 R328 R341
L481
STEPPING
25
4
51
SLDR
R718
R202
C472
C326
C369
C764
C763
C760
C769
C770
C319
C204
C202
R350
26
44
C759 50
27M C C206 C213
C781
C217
R215
C471
C208
C215
R209 R240
CN114
R236 R210
52 1 C358
11
IC751 52
R204
R481
1
R490 IC751
R208
R489 C212
C782
1 IC481 16 53
IC481
16
1
R211
208
53
208
C241
I CN101
C475
C476
FE TE CONTACT SIDE
R473
R241
C207
26
26
CONTACT SIDE
C773
25
CN114
25
RFO CN101
PU
C774
R475 C753 R129
8
9
C484
26
9 C127
C477
8 R474 R115 C216 C119
26
R139
R149
R495 R476 R212

C481 R486 R242 VREF
R781
RF-
X481
C754
RF+
C775
R134 B3
C117
C776
R120
C107
B4
CN111
R761
R485 R491
A
C755
R480 C480 R492 B2

2
2
R117 B1
1
1
C777
FDRV
C790
R138
C126
CN111
R755 D R118
C128
1
R754 C106
R286
C281
R284
R283
R282
R281
R285
C282
C123 C100
C778
1
R162
Q103
Q103
C779 C108 R163
R119
R150 C103
C274
C271
C273
C272
C780 R164
R161
R121
C756 R165
C798 C392
C794
C795
C
157
C791
R390
104
104 R166 R389
C470
157
R756
LOAD
CN103
C487 105
R757 105 5
156
C792 156
ASSY
C771
R167
4
R168
DVDM
55
5
VNP1886-
C761 C101 1
C283 R287
C284
D C762
PICKUP
IC791 C285 C393

IC791
R751
C768
C767
R555 C752 R422
R288
R846
R844
C841
R583
IC281
IC281
R759 4 1
C758
C757
1
R752 4 1
11
77
R791
C796
R833 C832 5
IC271 8
R946
1
R803
C845 R837
C805
R806
R289
R954
R758
IC271
C422
C834 R838
2121
C833
5 8
1
R836 R802 5 1
8
R753
C286 R290
R807
R811
R808
R814
R810
C804
JACK(AUDIO)
C270
R579
R809
C766 2.5V R406
D402
C840
R570 C751 R875
CN103
C807
R805
6464 49
49
C793 C913
13
13
R843 IC801
IC801
R813
R835
R568
C772
R760
48 37
C909
1 50 R845
R812
11
R839
4848
48 37
C803
36 C806
1
36
1
C411
C809
CN551
C837
EV4
C838
R632 R841
IC831 R842 5S
IC831
C839
C810
C412
C843
25
R563
12
12 IC403
C801
C844
IC403
13 24 25
D401
R872
R928
C812
C917
C84216
R403
16
C852 13 24
3333
C811
C916 C912
5V
R577
1717 32
32 R817 C808
C414
2111
R818
21
R815 C816
R871
R859
R816
B
R936 R950 R804
C815
R822
R823
R821
IC901
C847
A CN601
C401
C846
IC901
R937 R951
CN561
C851 R404
CN551
R944
R863 R862
R831
R908
KN2 C924 R868 C850
R832 R947
R855
Q933
R864 Q933 R856
R923
25 26 C848
C932
R997
EV6
R940 C849
C CN101
C802
R854 R873
EV3
R938
CONTACT SIDE
R866 R960
R929
1
R986
1
Q934 Q932 R865 Q932 Q934 NP
R958
R957
R945
R931
R959
C931 C933
CN401
PW
R801
R933 R948
CN401
CN951
R996
C908 C903 DVI R964 R963
Q931
Q931
29 CN901
R985
1 R934
HEAT RESISTANCE 1 29 R935
PRI-FLUX R943
R939
1
1 30
30 R942
22 30 1 30
R907
R898 C902
CONTACT SIDE 30
CONTACT SIDE
CN912
T.O. JACK(VIDEO)
(VNP1886-D) B DVDM ASSY C CN701 CN901
G CN101
A
SIDE A
4.2 DVDM ASSY
4 3 2 1
8 7 6 5
49 DV-757Ai
B
F
SIDE B
CONTACT SIDE R597 CONTACT SIDE
(FIRST) R532
20 2
40 2
C746
19 1 1 7 CN412
C747
50
C599
26
39
IC741 CN513 1
IC741
CONTACT SIDE CN542
IC603
IC603
C601 25
24
R594
R596
R727
C602
R601
R685
R595
25
C631
R665 1
C722
R609 R684 C741

R659 C727 C744 C743
C297 C742 C712
R722
R298
C650
C720
C718 C715
C726
1
R650 C622 48 D601
104 53 C713
R680
105
C730
R613
52
C735
R621
R618
C619 R682
R614
Q601
Q601
E
R589
R634
C609
R617
C629
IC701
R616
R612
IC701
C704
C623
C608
R625
R715
R712
C731
R689
R600 R610
R257
R259
R642
R639
R254 C706
R255
C246
C707
R258
R716
C245
IC211 R260 R717
C256 C709
C732
R703
1
28
R225
IC211
R256 C253
C235
R226
R218
R253
4
R227
C247
R251
1
C237 R677
C251
C710
R702
C248
C258
156
C249
R252 C733
C254 R220 208
IC251
C232 C728 157
R799
C736
C234
R228 R709
C214 R797
C252
C255
C719
IC251
Q210
C721
R233
Q210
C729 R796
R707
R234
C705
R343 C724 R794

R203
C390 R708 R334

C725
L330 C320 C723 R793

C716
C717
R720
R710
R711
R330
R246
C336 R320 R498 R792
14
C333
C332
5
5
1
1
15
C250 R582
R213 R214
C220 R345 R496

R723
R719
C708
C714
R219 R581
R344
C334 C335
R342
C323
R333
R375
C488
D302
3
C329
IC351 R374 IC351

C310
D
4 5
4 5
3 1
R364 C495
C324
R329
22
R335
R368 42
C365
C366
R372
R373
C361
C330
C371
C490
R315
1 C328 3
R371
C493
4
L304 R332
C321 R331
R363
D303
C322
R336
IC491
IC491
IC781
IC303 IC305 44 34
R369
R321
C370
IC306 R499
R361
1
Q241
33
IC304
IC304
R370
Q241 C789
R148 C112
IC781
R362
R147
R116
28
27
1 21
C353
R146 RFO
C351 C242
R351 R145
Q104
Q104
R353 R131
C124
Q106
R171
C120
C121
R122
C115
R132
R133
11
C359
23
C355
C354 R355 12 22
C116
Q106
R130
R365
R144
R354 C118
R123
C114
C113
R159
R172
R136
R135
C491
C494
TP2
49
R142
R141
64
R143
PN
R128
C788
IC552
IC552
C784
R357 R360 C122 C797
TP1
C111
20
13
C360
1
C357
48
1
R366
12
C356 R359
C130
R140
R356 R358
C783
C110
C553
R127
C125
C554 C552
C109
C787 C786
R105
1
R126
C555
54
IC786 Q935
R106
11
10
24
IC786
1
R137 R962
16
R107
33
R980
C785
R956
C938
R560
R559
R550
Q935
R561
C
IREF
R103 R152 R108 R124 R979

IC101
R102 R151 R109 17 32
IC101 R795
Q940 Q101 R101 R154 R110 R125 R976
R104 R153 R971
R586
C105
R553
R552
R551
Q940
R565
IC553 Q102
5
4
Q101
C940
Q937
R155 C102 C104 Q937
Q102
C133
R572
R972
C424
R156 R893 R905
1
R112 R114 R977

8
IC553
R952 L751
R157 R897 C934 R894 R903
R158 R895 R896 R904
C134
R574
C898 C899 R906 C556
R990
R992
C897 R901
R111 R113 R763 R899 R554
R2
R1
R4
C425 C423
R3
C765
C421 R900 R902
R588
C895
C896 C905
9
8
7
6
5
4
3
2
120 81
9
8
7
6
5
4
3
2
C894
C900 C901
9
8
7
6
5
4
3
2
AWX8 1 1 1
C904
R924
R576
C419
80
121
C420
VWS1 0 0 0 -A
C907
C906
C403
C910 C914
R556
R925
R419 R402
C417 C835
R405
Q941
R998
4
C418
5
R820
R819
C410
R987
C415
Q941
R926
C416
R988
IC402 IC402 C911
7
1
B
R421 R966 R978 R973 C836
C405
IC931 R840 R911 R910
R967 R981 R974
IC931
C814
9
8
R927
Q936
C407
C406
519R
C813
R909
160
Q939 619R
C918
C915
41
Q936
Q939
Q938
129C
R834
C409 R401
Q938
1
819R
R914 C923
16
1
5
R912
R567 1 C891
40
IC902
3
4
C922
R562 C920
R994
C404
IC902
R995
C936
C413 R993 R564
IC404
IC404 C930
C927
R557
R982
C919 C929
C935 C939 C937 R585 C893
R955
R932
R961 R975 R970 R917
C947
C948
R949 R913
C928
R999
R891
C945
R965
C941
R941
R969 R571 R558
R984
R921
C942
R919
R920
R922
R968 R983
C943 C944 C946
(VNP1886-D) B DVDM ASSY
A
SIDE B
8 7 6 5
887-
38
W285
55
W286
C753
C105
2
JACB
1
W287
2
CN705
W204
C101
W239 GNDA
C751
6
W288 LRCK1 DATA1

BCK1
C107
EV+6V DATA2
C103
XCS2 XMMUTE
11
XCS1
B CN901
W240 V+12V
V+12V
JA701
CONTACT SIDE
SQEEZE
4
EVER6,SW5
4
GNDA W241 XCOMP
EVER6,SW5
CN701
LETTER
IC102
IC102
IC101
IC101
GND
W333
C GND
W328
YELLOW
Y GND
Y/G P/XI
Cb/B VSEL1
Cr/R
V+12V
C742
78M08
78M05
VSEL2
TXD CTS
W329 RXD DTR
JA703
W330 GNDD
W443 GNDD
CN701
C741
W444
W289
EV+6V
30 30
VWV1926(6500ARAM)
VWV1925(655ALB)
VWV1914(656AWY)
VWV1913(656AKU)
VWV1912(45AKU)
W205
GNDD W242
W243
3
W206
GNDD W290
GREEN & BLUE & RED
W207
C721
W208
3
3
W291
W244
2
C761
W496
W292
JA702
W209
W248
W293
W245
W246
W247
W332
DV-757Ai
C762
VWV1918(757AJJ)
VWV1917(757AiWY)
VWV1916(47AiKU)
VWV19**(655ARD)
VWV1915(655ARL)
4
1
W210 W294
C763
C701
W249
W250 W425
W211 GNDD
C725
W449
W261
GNDD W445
W296
C775
W435
W446 GNDD
Print side
GNDD
IC702
W295
IC702
GNDD
5
VWV1921(858AViJ)
VWV1920(49KU)
VWV1919(755AiRL)
6
2
2
C772
(VNP1887-D)
RY701
5
6
4
CN703
W429
RY702
9
W447
C771
8
10
1
W448
W434
H CN901
GNDD
10
C702
1
+5V
W430
W433 V+12V
W298
C782 W336
C JACB ASSY
W214 GNDD W431

W297 W335
1
1
W432
4.3 JACB ASSY
GNDD +5V
CN801
GNDD W337
W216
7
19
W263
GNDD
W215
W262
W264
W265
W307
W266
C781
V+12V
W436
19
AUDIO_L V+5V
GNDA
W218
GNDD
W305
AUDIO_R
W306
C804
VSEL1
CN702
SQEEZE
D
V+12V
W217
GNDD
GNDD
CONTACT SIDE
CN702
GNDD
WARNING V
GND
1
1
SIDE A
E
THIS PRODUCT CONTAINS LEAD IN SOLDER AND CERTAIN C
ELECTRICAL PARTS CONTAIN CHEMICALS WHICH ARE KNOWN Y
TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH
W299
G
KN102
DEFECTS OR OTHER REPRODUCTIVE HARM. HEALTH & SAFETY VSEL2
B
CODE SECTION 25249.6 - PROPOSITION 65 R
C
1
50
C
D
A
F
8 7 6 5
51 DV-757Ai
C
F
D CN902
CN102
1919 1
1
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
GNDD
W370
GNDD
GNDD
GNDD
GNDD
DSD_R
DSD_L
CN102 W390
DSDBCK
DSD_Ls
DSD_Rs
DSD_CT
DSD_LFE
DSD_MCK
W393
W394
W377
W395
W380
W389
W423 DSDSEL
E W388
W386
W387
W382 W426
W371
W383
W384
W381
EV+6V
V+3D W421
W378
C405 W385 C505 GNDD W420

W363
C502
W418
W356
W372
W373
W374
W375
W376
W359
W354
B
W422
GNDD
W353
C301 W369
W407
W408
W357 W414
C201
W409
W403
W415
W437
C402 W413
W406
W355
W440
W411 C501 W417

C401
W339 GNDD W438 W410

W416
W338 GNDD W401 V+5A W441
C410 W412 V+5A
W442 GNDD
C306
C303
W348
C305
D
C420 W346 C520 C510
W347 W424
W341
GNDA W343 W351
W342
C416
JACB
C310
C320
C311
C321
W325 V+12V
W313 W316 W322 V+12V W324 V+12V VNP1887-
C314 PC
W317 V+12V W321 V+12V W323 V+12V Production Code
C380
W315 Vref C324 W320 Vref W327 V+8A
W314 W318 W319 Vref W326 V+12V
C109 GNDA GNDA
W280 Vref
W274 W278 Vref W281 GNDA C101
GNDD W279
C331
C336
C330
C346
C341
C340
W273
GNDD W277
DC FC
W272 C374
GNDD
C
GNDD
IR V+3D
W283
C372
W284
W285
W286
GNDD PCMMCK
DOUT GNDD
V+5D DATA0
GNDD BCK0
GNDD LRCK0
W287
W275 C516
C334
C344
SEL_IR V+3D
XAMUTE XCSDF0
GNDD W282
XDACRST0 XDFSO
W276 W234 V+12V W238
2CH_LFE_ON XDFSCK
V+12V
GNDA
21 W221 1 GNDD W229 VMUTE

19 1
W219
EV+6V
C338
W224
W225
W239
W227 VMUTE
VMUTE
W230
CN101 W226 W232
CONTACT SIDE W223
C414
W235
W236
W237
W228 W231
C105
C524
C514
W220
GNDD W222 W233
C360
C350
C424
A C604
C753 C751
W201
KN101
W202
W204
L601
C605
C110
JA301 W203 JA302
JA802 JA801
JA601 FR FL FR FL Rs Ls LFE CT
JA602 CN704 CN705
B
1
3 1 6
C 2
4 55 2
TZ
CN101
B CN551 BLACK RED & WHITE BLACK
A
SIDE A
8 7 6 5
RXD
R131 CTS
TXD
C756 R130 Cr/R VSEL2
R753 C104 C108 VSEL1
R129
R124
Cb/B
P/XI
R755
C752
Y/G
D101 GND
R125
Y
C GND
GND
R756
V
R757 EVER6,SW5 LETTER
VMUTE
EVER6,SW5 XCOMP
SQEEZE
R432
R433
V+12V
C754 XCS1 V+12V
XCS2 XMMUTE
C757
DATA2
Q431 Q432
R758 BCK1
Q432
DATA1
C758
LRCK1
R123
EV+6V
R791 Q431
C517
4
4
R430
R533
Q532
R530
R532
V+12V
Q532 R518
V+12V
Q531
Q533 Q531
V+12V
R511
C512
Q534
V+12V
R512 C513
V+5A
Q534
V+8A
CT
R534
Q533
IC502
R535 C119 EV+6V

R536 R516
VMUTE
R514
CT
Q520 Q510
C511
R510
R515 Q510 R513 1 4

LFE
C120
C523
R526
C515
IC501
R523
Q530
R531
Q520
Q410
R524 Q530 IC501
R525
R412
C525 Q410 R416 C522

R522
C521
LFE
R521 R520 DSD_MCK
IC503
C503
R415
DSD_CT
20
R527 GNDD
1
IC503 DSD_LFE
R418 DSD_Rs
R414 DSD_Ls
C508
R411
DSD_L
R401
R410
Ls
C504 DSD_R
10
11
C415 R425 DSDBCK
Q352 Q351 Q350 Q420

V+12V C411
R413 DSDSEL
Q371
C412
Q371
Q420 R426
3
3
R424 GNDA C413
C425
R377
R376
R517 R380
R423
R352
R351
C373
R121
VMUTE
Rs
R378
Ls
8 5
GNDA
GNDA
R374
R375
V+5A
C507
1
C417
IC402
IC402
Q350
V+12V
R353
GNDA
R354
R357
R350
R118
8 5
FL
C506
R355
Rs
C361
V+12V
Q351 V+12V
1 4
FR
Q370
IC401
C421 R117
R358 R368
CN102
Q370 IC401 R116
C381
C371 C422
C423
C352 D380
IC403
DV-757Ai
20
1 4 R421
1
R356 Q352 IC403
R363
IC305
IC305
R427 R420
V+5A
R372
R373
R379 R115
C370
R422
R114
Q362
R362
R371
Q362 R113
FL
10
11 GNDA
R417
C403
R321
C362
R370
Q360
Q430
Q430
R340
R367
R360
R361
C116
CN102
C404
IC303
IC303
Q360
8 5 R211
C351
FR
GNDD
V+12V
R119
R366
FR
C407
C342 C406
19
C343 C309 R431
V+12V
R365 R607
R120
R315
Q361
R364
C325
R342
Q361 R343 R212
R341
1 4
C603
FR
R325 R344
R345 R320
Q322
Q322
C307 C115
Q312
Q311 Q312
8 5
2
2
GNDD
IC304
R606
14
15
(VNP1887-D)
C302
IC304 GNDA
R312
C339
GNDA
Q201
R322 R301
Q311
C602
R605
R604
C203
R331
Q201
1 4
R313
R332
Q321
Q321
FL
R311
IC301
28
1
R324 R335 IC301 R205
Q601
Q601
R334 C304
8 5
FL
C606
GNDA
R111
GNDD
IC302
IC302
R333
C112 R112 C333 R202
C308
C315
R314
V+
C332
IC202
R609
1
C JACB ASSY
5A
R603
R122
Q310
Q310
R206 IC202
CN101
R323
R602 R110
R201
R330 1 4
R109 C601
R203
R108
R608 R310
IC201
R107 XDACRST0 XDFSO C204
C801
R601
2CH_LFE_ON XDFSCK IC201
R104
Q320
Q320
R106 XAMUTE XCSDF0
CN101
R208
9
Q801
Q801
8
D801
GNDD LRCK0
R803
R105 GNDD BCK0
V+5D DATA0
R204
C114
DOUT GNDD
IC203
GNDD GNDD
R207
R210
R801 SEL_IR V+3D
R802
Q802
IR V+3D C117
C118
GNDD PCMMCK
16
1
Q802
21
R806 C808
1
1
D802
C111
SIDE B
C202 R209
GNDD
R132 R101
R808
R807
C113
C803
C802
EV+6V
R103 GNDD
C
R102 EV+6V
R804
R805
52
C
D
A
F
8 7 6 5
53 DV-757Ai
C
F IC701
Q701
E
CN702
D
CN702 CN701
GNDA
V+5V
VSEL1
1 19
R
VSEL2
GND
VWV1912(45AKU) VWV1915(655ARL) VWV1919(755RL)
VWV1913(656AKU) VWV19**(655ARD) VWV1920(49KU)
GND
GND
GND
DTR
CTS
P/XI
VSEL2
VSEL1
LETTER
XCOMP
SQEEZE
V+12V
XMMUTE
D T 2
B
G
Y
C
V
VWV1914(656WY) VWV1916(47AiKU) VWV1921(858J)
Y
C
V
R771
RXD
TXD
Y/G
VWV1925(655LB) VWV1917(757AiWY)
Cr/R
Cb/B
XCS1
XCS2
V+12V
V+12V
SQEEZE
R712
VWV1926(6500ARAM) VWV1918(757AJJ)
AUDIO_R
AUDIO_L
R713
R711
R126
EVER6,SW5
EVER6,SW5
R701 R715
R127
C704 R705 R714 R716
+12V
EVER+6 R128 R129
C784
30
C783 R702
Cr/R
GND Cb/B
R125
Y/G R124
C703 Y
+5V C
R796 CN701
R704
1
R772 R795
IC701 V+12V
V
C
EV+6V
C722
1
R131
R130
18
GND
C716
C714
+5V
C712
C106
C715
C713
C711
R794
R793
C726
19 36 C723
+5V
VWM2 0 0 0 A-
C733 V+5A
C108
Y C V 1 1 1
D713
2 2 2
Y/G
GND
Cr/R
Cb/B
Q701
C724 +5V 3 3 3 VMUTE
D701
D101
4 4 4 R433
C102
+5V 5 5 5
D708
V+8A
C104
D707
D706 D705 6 6 6
R432
D709
D704
D710
GND
+5V
D712 7 7 7
D702
R756
C732
D711 8 8 8
C754
D703
R767
C774
R753
9 9 9
L703
R765
R769
R766
L704
C755 C752
R760
R754
R757
L702
L701
R761
Y Cb Cr
R755
R759
B
R751
R752
R764
Cr Cb
R768
C756
C805
R770
C776
R762
C765
C764
C743
C744
C773
C757
R763
C766
7 1
A
SIDE B
8 7 6 5
1 2 3 4
4.4 SACDB ASSY
A SIDE A SIDE A
C CN102
CN902
0 1 A SACDB VNP1885-
CONTACT 0 1 2 3 0 1 2 3 4 5 6 7 8 9
B 3/4
C
NE M C2
SIDE 0 1 1 VWG2352-
IC903
C916 R902
R907 IC903 C909
R912
R911
R910
R909
21 CN999
R906 C903 VWG2353-
A
C904
C801 1
FC DC
19 19 CN902 1 R905 R904
R903 C915 VWG2378-
C807
5 4 VWG
C808
C809
C810
L801 1 3
C811
C812
C905
C829
C831
IC902 108108
7373 IC902 AWX8156-
IC801 IC801 C920
C917 C918 C919
109
72
109
72
50
1
C815 132
C914 89 C911
C819
C906
133
C907
PC
B 88
C823 C820
C816
IC902
C923
C821
C928
C912
R915
C913
IC801
C826
C822
C930
R920
C947
C830
144 IC901 R921
C924
C927
144
25
R926
3 R812
37
R924
37
5 4
26
11 36
36
R849 1 3 C902
C833 C925
C946 C938
4
C929
C837 8 5
R930
C802 5 4
C834
C835
C836
1
1 3 C926
5
R822
11 176 45
IC806 R823 4
C901
IC806 1 44
IC905 R814 IC905
C844 C944
C843
IC808 IC901 IC808 C840 C941 IC901
C828
C942
C827
C945
C935
B 7 5
R908
R916
R917
IC906 7 5 C943
R931
IC906
C934
C921
R809
C937
C940
IC904
R810
C832 R923
C824
C936
IC904 C922
C976
C975
C974
C933
C842
IC804 IC804 R922
R928
C C972 C951
R927
1 4 C955
1 4 C973 C971
C841 C977 11 19
19 1
1 39
39
C956
22 20 2
2 40
40
C839 CONTACT SIDE
11
CN903
13
13
CN801 CONTACT SIDE
20
CN901 CONTACT SIDE
C
CN903 CN801 CN901

I CN102 B CN502 B CN531
SIDE B D SACDB ASSY (VNP1885-B)

SIDE B
R979
R978
R977
R976
R975
R974
D
R973
R972
R971
R828
R830
R832
R834
R967
R951
R968
R955
R980
R982
R957
R959
R961
R800
R914
C979
C978
R840
R952
R953
R956
R981
R983
R958
R960
R962
R984
R985
R986
R987
R964
R965
R966
R824
C910
R801
R827
R829
R831
R833
R841
R842
R843
C991
R839
R925
5
C932
C952
IC991 IC991
R856 1
R846
R991
R848
R901
R845 C931
R929
R844 R918 R998
R992
E R999
C908
R919
R913
R808
R855
R807 9 9 9
18.DSDMCK
16.DSD C
14.DSD LFE
12.DSD LS
10.DSD RS
R854
8.DSD L
6.DSD R
4.DSDBCK
2.SACDSL
8 8 8
7 7 7
R815
R847
R819
R817
R816
R818
R806 6 6 6
5 5 5
DSADML
DSADMR
C950 4 4 4
3 3 3
2 2 2
8 1 1 1
R941
19 1 2 0 0 0
VWG
R942 AWX
R943
R949
R948
R947
R946
R945
R944
CN902
D D
54 DV-757Ai
1 2 3 4
5 6 7 8
4.5 SCRB ASSY
SIDE A SIDE B A
SCRB ASSY C CN702 SCRB ASSY

H (VNP1887-D)
CN901 CN901 H (VNP1887-D)
IC901
R947
R948
R961
19
IC901
IC902
19
R
CN901
R
19
W140 B
IC902
VSEL2 B
G VSEL2
1 3 1
6
W139 GNDV G
Y GNDV
Y C939
4
GNDV
C929
3
C
C936
W138 GNDV C
1
V
W137
GNDV V C938
+12V
W167 GNDV +12V
W136 VSEL1 C940 R935
CN901
W172
VSEL1
SQUEEZE C920 C928 D920
SQUEEZE R927
GNDA
Q905
GNDA AUDIO.R
B
W166 AUDIO.R
D905
C916
V+5V R923
D919
AUDIO.L
Q905
1
V+5V
1
1
AUDIO.L
JA902
C930
Q904
R924 R954
W115 D906
Q904
C935
R936
R928
C934
V
C927
C948
R958
W135
W134
W114
W165
W113
R
W164
C959
R938
R939
C909
R937
JA902
C908
W163
W133
W162
R932
G
W132 R926
5
6
W131
VNP1887-
VWV1922-
R933
RY903
W161
R940
B
W112
10
1 W130
C932
W111 D904
W160
C943
C913
R949
VNP1887-
C925
W159
D911
C903 C
C937
W158 W129
SCRB VWV1922-
D909
C933
R950
R943
R942
D907 R951
W157
D908 R952
+12V
5
6
W156 W128
R944
R953
RY904
R945
R946
W110
W109
R922
W171
R921
10
W170 W127
R997
W155
C941
W154
SCRB
D910
GNDV
W173
GNDA
GNDA
+12V
+5V
GNDV
GNDV W153 W152
GNDV W169 W151
W126
5W123
R965
W124
W108
W105
W168
W106
W125
W107
C951
6
R962
R999
RY905
C953
R956
C956
10
D918
D915 C945
R957
W177
W150
D916
R955
R964
IC903
D917
C946
D913 R966
IC903
R998
4
W149
6
R929
W122
C947
C957
D912
+12V
R919 R934
V
R968
D914
5
6
R930 R925 R918

W175 C924
RY902
W176
R967
C923
JA901
R
R941
W120
R920
10
C944
D903
W103
G
W148
W174
C917
W147
Q903
W119
C958
Q903
C901
R916
W118 +12V
GNDA
B
W117 C942
W146 W102 R905
C905
R909
R904
E
5
6
R917
C914
Q901
W145
R903 R912
RY901
R931
C906
W144
Q901
R902
C921
Q902
Q902
GNDA
10
R908 R915
1
C907 C910
R913
W143 D901
C904
R911
W142
C902 R914 C950
R901
R906
R907
D902
W101
R959
R910
W141
C919
JA901
H H
DV-757Ai 55
5 6 7 8
4 3 2 1
DV-757Ai 56
(VNP1891-B) KEYB ASSY F CN101 E F
F
D
F
R215 D211 D212
R204
R202 R208 C201
R214 R223 C202
R216 R207
R213
1
R212
R201 R211 R221
E
R224
R206
R203 R205
9
8
7
6
5
4
3
2
1
9
8
7
6
5
4
3
2
1
R225
C
9
8
7
6
5
4
3
2
1
2000
CN201
A R222 2/2
VWG
CN201
B
C291
C292
E
0
1
2
3
4
5
6
7
8
9
1.GND
0
1
2
3
4
5
6
7
8
9
2.LED7
1
2
3
4
5
6
7
8
9
VWG
CN102
3.LED6 G
2 0
4.KEY0
13.s(MtoF)
12.GND
11.SCK
10.XREADY
9.IR
8.PW_ON
7.FLDC+
6.XRESET
5.FLDC-
4.LT1
3.-28V
2.SEL IR
1.GND
5.LED5
1
6.STBY
R120
C110
R130
CN102
R147 Q103
R183
D
R181
R182
9
Q102
R146 R145 R144 Q101
R101
Q103 Q101 Q102

SIDE B
V101
9
9
VWG
W161
3 1
W165
CN102
W121
VWG2360 5 4
W120
1
1
W162
W119
W118
W117
VWG2359 IC103
W158
W101
W115
W114
VWG2358
CN102
W116
VWG2357
C104
L101
W157
FLKY
9
9
NE M PF2 CN202
CN201
1 2
S204 2/2 PW
S201 S202
B
PC S203
W201
1 2
CN201
VWG
1
1
VWG2371
FL PROGRE
VWG2370
D204 D206 VWG2369
FL-OFF D203 D205 VWG2368
PROGRE i-Link STAND BY
D201
J201
(VNP1891-B) CN101
KEYB
A
KEYB ASSY F
J CN302 SIDE A
4.6 FLKY and KEYB ASSYS
4 3 2 1
5 6 7 8
SIDE A A
E FLKY ASSY (VNP1891-B)
PC J101 B
2/2
W122
C100
W146
X101
W145
W152
W170
W150
W151 W153
W168
W127
S101
W148
W149
W147
W144
W109
FLKY
W134
OPEN
W108
VWG2357 /KU/CA
W123
W130
W132
W133
W136
C106
VWG2358
W139
W140
/WY
W128
W137
W138
W135
W141
W142
W143
W129
VWG2359
W124
/J
W131
PAUSE
W169
REV PLAY
W111
VWG2360 /RL W166 S103
S106
STOP S104 C
W107
W165 W156
W106
17 W113
1 17
S105
VWG W167 S102 CN101
FWD W112 1
NE M PF2
CN101
B CN402
IC101 IC102
SIDE B
Q103 Q104 Q105
R145 R146 R148 CN101
R149
R150
Q105
R118
R115 C103 R116

I
R182
CN101 1
R181
D
17
R183
R147 Q103
R113
R112
Q104
R151
R123
R103
R104
R102
H
R108
R114 R191
R119 R117
R129
R121
41
40
R138
C111
R139
C105
R107
R152 R161
R196
C102
C113
C116
5.FLDC-
6.XRESET
7.FLDC+
8.PW_ON
9.IR
10.XREADY
11.SCK
12.GND
13.s(MtoF)
14.E+3V
15.S(FtoM)
16.12V
17.1394RST
R142
C114
R141
R143
R127
C107
R140
60
21
R137
R128 R126
C161
61
20
R110
R111
R109
R122
R133
C109 R194 R198

R197
1
10
IC
R199
R136
R134
R135
R195
80
C115
C101 1
R106
C108
R105 5 E
IC102
M
L K
2/2
E FLKY ASSY (VNP1891-B)
E
DV-757Ai 57
5 6 7 8
1 2 3 4
4.7 POWER SUPPLY UNIT
A SIDE A SIDE A
AC INLET ASSY
CN1 G POWER SUPPLY UNIT
B
CN2
J CN302
Q2
Q1
Q20
Q320
VR201
B CN401
IC103
IC201
CN101
Q412
Q411
Q410
G G
58 DV-757Ai
1 2 3 4
B
F
C
D
A
59
SIDE A
SIDE B
IC102
IC202
IC307
IC205
I
8
8
C326
C346 CN103 C344

C152
B
L4 JA1
JA2 7 1
1 1 C325 7 1 C327
C323
C341
C321
C342
C322
C324
A
R154
R153
R152
R151
C151 C328
L202
L204
L201
L203
C202
D201
D202
D203
D204
D209
D210
D211
D212
3 1
1
R371 R162
4 6 CN103 C348
R374 R375 C345
C329
R164
R163
R161
R165
D205
D206
D207
D208
1.TXD0
C343
D213
D214
D215
D216
R373
C285
2.RXD0
C286
C411
3.DTR0 C347
R218
R372
R282 4.CTS2
Q104 5.V+5D C330
R287 R281 C273 R290
R274 6.GNDD
C205 R288 R286 R111 R273 C283 C284
7.12V C270
R285 R276 R289
R363
R283 R365
R366 R277 C282 R208
C203
R284
X201
14 8
C232
C281
C278
CN101
IC102
R215
C109
R205
C206 C222 R364 3 1
1
R367 R216
C231
1.V+5D R204
C276
R279
C221
2.GND
C208
C207
C204
4 5 R272 R206
3.V+3D
C271
R271
1
1 7 IC204 4.V+3D 8 R209

R207
1 5.GND
C220 IC203 6.1394XRDY L6
CN104
R251
R227
C272 7.1394LT
7
7
R250 C209
C108
8.S(MtoF) R211
R141
R142
R253 C277 9.S(1394toM) R226
C218
R252
C219 10.XRESET R213
R212
L3
R355
C211 R225
R232
R368
11.1394SSCK 16
1
12.GND R352
5
R353
IC201
13.1394MCK C215
R275 R351
14.GND C214
R219
C210 C274
ILKB
15.1394SPDIF
C275
R350
R254 16.GND
R257
C217
R255 R280 17.22/24M
C107
C279
R143
R145
18.GND
C105
L2
C106
19.1394BCK
R349
R346
DV-757Ai
20.1394LRCK
C213
R256
21.1394DAT0 C216
R260
R259
R258
R214
22.1394DAT1 1
23.1394DAT2
24.1394DATA
C212
(VNP1890-A)
1
R222
R104 IC205
C223
1
1
R265
R103
(4/4)
R109
CN105
R119 R118
R110
R126
R127
R220 R221 R223 R116 R117
R136
C103 R108
R266
VNP1890-
51
IC202
75
75 51
VWG2391-
76
R139
R140
84
50
76
VWG2391-
VNP1890-
R129
R267
6.DSDA
5.FRAME
4.GND
3.GND
2.IOUTE
1.GND
8
50
1
8
8
R102
R107
D261
CN102
R128
R268
IC101
R101
13.GND
12.DSD0
11.DSD1
10.DSD2
R125 C261
ILKB ASSY
C262
9.DSD3
8.DSD4
7.DSD5
C104
6
6
R138
94V-0
R269
R137 C405
R112
26
C102
100
26
100
R270
R340 R339
R124
42
52
25 R134
1 25
C401
R401
R402
20 11 R130 R106
R344
20 11 IC306
R105
C101
C404
R122 R333 1 C406
R336
C301
C308
C403
L1
D
4 1
R343
R342
X101
C426
C425
R332
R341
C333
IC302 1
C424
C423
C306
C422
C421
L5
C307
IC307 R337 R338
C
1 10 R331 C334
IC301 IC401
1
C302
1 10
R334
C309
1 R335 C331
1 IC308 C402
C412 5 7
R309
13
13 11
IC309 1 24
24 11
CN101
CN102
I
4.8 ILKB ASSY
CN102 CN101
D CN903 B CN701
Q104
5
5
SIDE A
SIDE B
IC301
IC302
IC309
IC201
IC203
IC101
IC306
IC204
IC401
IC308
I
1 2 3 4
4.9 MSWB ASSY
A SIDE A SIDE A
VWG2390 VWG B
PC
G CN2
3
A
4
1 2
CN302
NE M PF2
C301
5
CN302
6
PRIMARY
C
1
D
7 8 1 CN301 MSWB
S301
C 2/2
CN301
F CN202
J MSWB ASSY (VNP1891-A)
SIDE B SIDE B
D
CN301
2/2
C311
CN301
1
9 9 9
8 8 8
7 7 7
CN302
6 6 6
5 5 5
CN302
4 4 4
E 3 3 3
2 2 2
1
1 1 1
0 0 VWG2 0
J J
60 DV-757Ai
1 2 3 4
5 6 7 8
5. PCB PARTS LIST

NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
A
The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
When ordering resistors, first convert resistance values into code form as shown in the following examples.
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%,
and K=10%).
560 56 x 10 1 561 RD1/4PU 5 6 1 J
47k 47 x 10 3 473 RD1/4PU 4 7 3 J
0.5 R50 RN2H R 5 0 K
1 1R0 RS1P 1 R 0 K
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).
5.62k 562 x 10 1 5621 RN1/4PC 5 6 2 1 F
Mark No. Description Part No. Mark No. Description Part No. B
PRINTED CIRCUIT BOARD VNP1836
LIST OF ASSEMBLIES
B DVDM ASSY [VWS1540]

[DV-757Ai/WYXJ]
NSP 1..LOADING MECHA ASSY VWT1203
NSP 2..LOAB ASSY VWG2346
SEMICONDUCTORS
IC831 ADV7300AKST
1..DVDM ASSY VWS1540
IC261, IC302 BA4510F
IC251 BA6664FM
1..JCSB ASSY VWM2149
IC741, IC901 HY57V161610DTC-8
2..JACB ASSY VWV1917
IC101 LA9704W
2..SCRB ASSY VWV1922
IC201 LC78652W
1..SACDB ASSY VWG2353 C
IC781 M2V64S40DTP-7
IC351 M56788AFP
1..FLKB ASSY VWM2136
IC751 M65776AFP
2..FLKY ASSY VWG2358
2..KEYB ASSY VWG2369
> IC404 MM1385EN
2..MSWB ASSY VWG2390
> IC791 MM1561JF
1..ILKB ASSY VWG2391
> IC402 MM1565AF
IC552 PD0274A
IC601 PD6345A
> 1..POWER SUPPLY UNIT VWR1361
IC701 PE5286A
IC491 PE9015B
[DV-S755Ai/RLXJ/NC]
IC902 PM0033A
NSP 1..LOADING MECHA ASSY VWT1203 D
> IC403 PQ025EZ01ZP
NSP 2..LOAB ASSY VWG2346
IC481 SM8707HV
IC786 TC74VHC541FT
1..DVDM ASSY VWS1534
IC303, IC304, IC306 TC7SZU04F
1..JCSB ASSY VWM2151
IC553 TC7WH157FU
2..JACB ASSY VWV1919
IC211 TK15404M
IC603 VYW2045
1..SACDB ASSY VWG2353
Q210, Q932Q934, Q936 2SA1576A
1..FLKB ASSY VWM2138
Q938, Q939 2SA1576A
2..FLKY ASSY VWG2360
Q241 DTC114EUA
2..KEYB ASSY VWG2369
Q101, Q102, Q106 HN1A01F
2..MSWB ASSY VWG2390 E
Q103, Q104 HN1B04FU
Q931 RN1911
1..ILKB ASSY VWG2391
Q601, Q941 RN4982
> 1..POWER SUPPLY UNIT VWR1361 D302, D303 KV1470
D401, D402 RB051L-40
D601 RB501V-40
Mark No. Description Part No.
COILS AND FILTERS
A LOAB ASSY [VWG2346]
SWITCHES AND RELAYS
L304
L4080, L4090, L4100 CHIP BEADS
LCYA1R2J2520
VTL1074
L4110, L4120 CHIP BEADS VTL1074
S101 REAF SWITCH VSK1011
L4130, L4820, L4880 CHIP BEADS VTL1074
F
L4910, L4930 CHIP BEADS VTL1074
OTHERS
CN602 CONNCTOR S2B-PH-K L652 CHIP BEADS VTL1074
CN601 CONNCTOR S5B-PH-K L4720 CHIP BEADS VTL1079
DV-757Ai 61
5 6 7 8
1 2 3 4
L4710 CHIP BEADS VTL1081 C706C710, C712C716 CKSRYF105Z10
L4800, L481 CHIP BEADS VTL1084 C718C722, C724C732, C735 CKSRYF105Z10
A C741C744, C746, C747 CKSRYF105Z10
CAPACITORS C753, C754, C756, C757 CKSRYF105Z10
C480, C481, C662 CCSRCH100D50
C121, C532, C6270, C950 CCSRCH101J50 C759, C760, C763C765 CKSRYF105Z10
C953C955 CCSRCH101J50 C769C780, C782C790, C792 CKSRYF105Z10
C314, C474, C798 CCSRCH150J50 C797, C832C834, C837C839 CKSRYF105Z10
C100, C133 CCSRCH151J50 C842C846, C893, C900, C901 CKSRYF105Z10
C904C907, C909C918 CKSRYF105Z10
C120 CCSRCH181J50
C484, C485, C487, C667 CCSRCH220J50 C921C924, C927C930 CKSRYF105Z10
C134, C324, C391, C392 CCSRCH331J50 C956, C957 CKSRYF105Z10
C945, C946 CCSRCH331J50 C117, C128, C422 (100/6.3) VCH1194
C109 CCSRCH391J50 C119, C421, C424, C601 (150/4) VCH1195
B C623, C702, C751 (150/4) VCH1195
C297, C555 CCSRCH470J50
C241 CCSRCH560J50 C403, C405 (47/16) VCH1210
C107, C360 CCSRCH681J50 C411, C419 (100/6.3) VCH1211
C489 CCSRCH8R0D50
C123, C201, C233, C254 CEV101M16 RESISTORS
R831, R832 RAB4C0R0J
C368, C369, C413, C414 CEV101M16 R924R927 RAB4C101J
C103 CEV220M16 R631, R713 RAB4C103J
C205, C326, C401, C470, C472 CEV221M4 R111 RAB4C220J
C701, C711, C745, C752, C766 CEV221M4 R113, R534, R537, R704, R705 RAB4C470J
C781, C791, C793, C835, C891 CEV221M4
R138 RS1/10S0R0J
C C903, C908 CEV221M4 R341 RS1/10S101J
C101 CEV470M6R3 R141R148 RS1/10S220J
C116, C127, C223, C224, C264 CKSQYB105K10 R364, R369, R373, R375 RS1/16S1003F
C312, C406, C407, C415, C416 CKSQYB105K10 R123 RS1/16S1202F
C477, C794, C795 CKSQYB105K10
R843, R855 RS1/16S1501F
C216, C313, C351, C427, C531 CKSRYB102K50 R358, R361 RS1/16S1503F
C533, C534, C606, C617, C621 CKSRYB102K50 R755 RS1/16S1801F
C703, C748, C831, C925, C926 CKSRYB102K50 R936, R944, R950, R966, R973 RS1/16S3000F
C951 CKSRYB102K50 R978 RS1/16S3000F
C110, C113, C203, C220, C225 CKSRYB103K50
R754 RS1/16S3001F
C234, C261, C320C322, C330 CKSRYB103K50 R751 RS1/16S3301F
D C404, C426, C619, C920 CKSRYB103K50 R132 RS1/16S4702F
C108, C111, C114, C115 CKSRYB104K16 R357, R362, R363, R368, R372 RS1/16S6802F
C212, C213, C227, C231 CKSRYB104K16 R374 RS1/16S6802F
C248C251, C255, C263, C315 CKSRYB104K16
R257 (R=1.0) VCN1127
C317 CKSRYB104K16 R258, R259 (R=2.2) VCN1128
C106 CKSRYB152K50 Other Resistors RS1/16S###J
C208 CKSRYB222K50
C266 CKSRYB224K10 OTHERS
C206, C214, C242, C357 CKSRYB472K50 CN401 PH CONNECTER S13B-PH-SM3
CN103 CONNECTOR S5B-PH-SM3
C105, C118, C122, C253, C256 CKSRYF104Z25 9006 FLEXIBLE CABLE VDA1681
C332, C353, C359, C365, C366 CKSRYF104Z25 CN114 4P CONNECTOR VKN1409
E C609, C622, C631, C723, C755 CKSRYF104Z25 CN115 12P CONNECTOR VKN1416
C758, C761, C762, C767, C768 CKSRYF104Z25
C836, C840, C848, C849 CKSRYF104Z25 CN402 17P CONNECTOR VKN1421
CN551 21P CONNECTOR VKN1425
C895C899, C902, C933, C939 CKSRYF104Z25 CN701 24P CONNECTOR VKN1428
C202, C204, C215, C217 CKSRYF105Z10 CN502 20P CONNECTOR VKN1460
C221, C222, C226, C230, C232 CKSRYF105Z10
CN531 FFC CONNECT0R VKN1794
C319, C323, C328, C329, C409 CKSRYF105Z10 KN1, KN2 EARTH METAL FITTING VNF1109
C412, C418, C423, C428 CKSRYF105Z10 X481 (27.000MHz) VSS1159
C475, C476, C493, C494 CKSRYF105Z10 X601 (16.5MHz) VSS1160
F C552C554, C556, C602C605 CKSRYF105Z10
B DVDM ASSY [VWS1534]

C607, C608, C610, C613C616 CKSRYF105Z10
C618, C657, C658, C704 CKSRYF105Z10 SEMICONDUCTORS

62 DV-757Ai
1 2 3 4
5 6 7 8
IC831 ADV7300AKST C368, C369, C413, C414 CEV101M16
IC261, IC302 BA4510F C103 CEV220M16
IC251 BA6664FM C205, C326, C401, C470, C472 CEV221M4 A
IC741, IC901 HY57V161610DTC-8 C701, C711, C745, C752, C766 CEV221M4
IC101 LA9704W C781, C791, C793, C835, C891 CEV221M4
IC201 LC78652W C903, C908 CEV221M4

IC781 M2V64S40DTP-7 C101 CEV470M6R3
IC351 M56788AFP C116, C127, C223, C224, C264 CKSQYB105K10
IC751 M65776AFP C312, C406, C407, C415, C416 CKSQYB105K10
> IC404 MM1385EN C477, C794, C795 CKSQYB105K10
> IC791 MM1561JF C216, C313, C351, C427, C531 CKSRYB102K50

> IC402 MM1565AF C533, C534, C606, C617, C621 CKSRYB102K50
IC552 PD0274A C703, C748, C831, C925, C926 CKSRYB102K50
IC601 PD6345A C951 CKSRYB102K50 B
IC701 PE5286A C110, C113, C203, C220, C225 CKSRYB103K50
IC491 PE9015B C234, C261, C320C322, C330 CKSRYB103K50

IC902 PM0033A C404, C426, C619, C920 CKSRYB103K50
> IC403 PQ025EZ01ZP C108, C111, C114, C115 CKSRYB104K16
IC481 SM8707HV C212, C213, C227, C231 CKSRYB104K16
IC786 TC74VHC541FT C248C251, C255, C263, C315 CKSRYB104K16
IC303, IC304, IC306 TC7SZU04F C317 CKSRYB104K16

IC553 TC7WH157FU C106 CKSRYB152K50
IC211 TK15404M C208 CKSRYB222K50
IC603 VYW2045 C266 CKSRYB224K10
Q210, Q932Q934, Q936 2SA1576A C206, C214, C242, C357 CKSRYB472K50 C
Q938, Q939 2SA1576A C105, C118, C122, C253, C256 CKSRYF104Z25

Q241 DTC114EUA C332, C353, C359, C365, C366 CKSRYF104Z25
Q101, Q102, Q106 HN1A01F C609, C622, C631, C723, C755 CKSRYF104Z25
Q103, Q104 HN1B04FU C758, C761, C762, C767, C768 CKSRYF104Z25
Q931 RN1911 C836, C840, C848, C849 CKSRYF104Z25
Q601, Q941 RN4982 C895C899, C902, C933, C939 CKSRYF104Z25

D302, D303 KV1470 C112, C125, C126, C130, C200 CKSRYF105Z10
D401, D402 RB051L-40 C202, C204, C215, C217 CKSRYF105Z10
D601 RB501V-40 C221, C222, C226, C230, C232 CKSRYF105Z10
C236, C258, C265, C299, C310 CKSRYF105Z10
COILS AND FILTERS D
L304 LCYA1R2J2520 C319, C323, C328, C329, C409 CKSRYF105Z10
L4080, L4090, L4100 CHIP BEADS VTL1074 C412, C418, C423, C428 CKSRYF105Z10
L4110, L4120 CHIP BEADS VTL1074 C475, C476, C493, C494 CKSRYF105Z10
L4130, L4880 CHIP BEADS VTL1074 C552C554, C556, C602C605 CKSRYF105Z10
L4910, L652 CHIP BEADS VTL1074 C607, C608, C610, C613C616 CKSRYF105Z10
L4720 CHIP BEADS VTL1079 C618, C657, C658, C704 CKSRYF105Z10

L4710 CHIP BEADS VTL1081 C706C710, C712C716 CKSRYF105Z10
L4800, L481 CHIP BEADS VTL1084 C718C722, C724C732, C735 CKSRYF105Z10
C741C744, C746, C747 CKSRYF105Z10
CAPACITORS C753, C754, C756, C757 CKSRYF105Z10
C480, C481, C662 CCSRCH100D50
C121, C532, C6270, C950 CCSRCH101J50 C759, C760, C763C765 CKSRYF105Z10 E
C953C955 CCSRCH101J50 C769C780, C782C790, C792 CKSRYF105Z10
C314, C474, C798 CCSRCH150J50 C797, C832C834, C837C839 CKSRYF105Z10
C100, C133 CCSRCH151J50 C842C846, C893, C900, C901 CKSRYF105Z10
C904C907, C909C918 CKSRYF105Z10
C120 CCSRCH181J50
C484, C485, C487, C667 CCSRCH220J50 C921C924, C927C930 CKSRYF105Z10
C134, C324, C391, C392 CCSRCH331J50 C956, C957 CKSRYF105Z10
C945, C946 CCSRCH331J50 C117, C128, C422 (100/6.3) VCH1194
C109 CCSRCH391J50 C119, C421, C424, C601 (150/4) VCH1195
C623, C702, C751 (150/4) VCH1195
C297, C555 CCSRCH470J50
C241 CCSRCH560J50 C403, C405 (47/16) VCH1210
C107, C360 CCSRCH681J50 C411, C419 (100/6.3) VCH1211 F
C489 CCSRCH8R0D50
C123, C201, C233, C254 CEV101M16 RESISTORS
R831, R832 RAB4C0R0J
DV-757Ai 63
5 6 7 8
1 2 3 4
R924R927 RAB4C101J COILS AND FILTERS
R631, R713 RAB4C103J L701, L702 CHIP BEADS VTL1089
A R111 RAB4C220J
R113, R534, R537, R704, R705 RAB4C470J SWITCHES AND RELAYS
RY701, RY702 VSR1017
R138 RS1/10S0R0J
R341 RS1/10S101J
R141R148 RS1/10S220J
CAPACITORS
R364, R369, R373, R375 RS1/16S1003F C307, C406, C506 CCSRCH331J50
R123 RS1/16S1202F C115, C116, C118C120, C801 CCSRCH470J50
C702, C721 CEAT101M16
C701, C741, C742, C751, C753 CEAT102M6R3
R843, R855 RS1/16S1501F
C761 CEAT102M6R3
R358, R361 RS1/16S1503F
R755 RS1/16S1801F
C725, C762, C763 CEAT471M6R3
R936, R944, R950, R966, R973 RS1/16S3000F
C110 CEHAZA471M6R3
B R978 RS1/16S3000F
C605 CEJQ101M16
C604 CEJQ1R0M50
R754 RS1/16S3001F
C411, C421, C511, C521 CKSRYB272K50
R751 RS1/16S3301F
R132 RS1/16S4702F
C117, C407, C413, C423, C507 CKSRYF104Z25
R357, R362, R363, R368, R372 RS1/16S6802F
C513, C523, C704, C711C716 CKSRYF104Z25
R374 RS1/16S6802F
C732, C733, C752, C754, C803 CKSRYF104Z25
C111, C112, C114, C202, C204 CKSRYF105Z10
R257 (R=1.0) VCN1127
C302, C403, C503, C601, C606 CKSRYF105Z10
R258, R259 (R=2.2) VCN1128
Other Resistors RS1/16S###J
C703, C722C724, C726, C805 CKSRYF105Z10
C334, C336, C344, C346 (470P) VCE1035
OTHERS C330, C331, C340, C341 (4700P) VCE1046
C CN401 PH CONNECTER S13B-PH-SM3
C310, C311, C320, C321 (2200P) VCE1048
CN103 CONNECTOR S5B-PH-SM3
C412, C422 (1608CH330P) VCH1226
9006 FLEXIBLE CABLE VDA1681
C512, C522 (1608CH330P) VCH1226
C350, C360, C414 (C= 47) VCH1236
C424, C514, C524 (C= 47) VCH1236
C101, C103, C314 (C= 100) VCH1237
C324, C338 (C= 100) VCH1237
C372, C380, C401 (C= 100) VCH1237
C410, C416 (C= 100) VCH1237
C420, C501, C510 (C= 100) VCH1237
C516, C520 (C= 100) VCH1237
D CN531 FFC CONNECT0R VKN1794
C107, C109, C201 (C= 330) VCH1239
KN1, KN2 EARTH METAL FITTING VNF1109
X481 (27.000MHz) VSS1159
C301, C303 (C= 330) VCH1239
X601 (16.5MHz) VSS1160
C402, C502 (C= 330) VCH1239
C305, C306, C405, C505 (C= 47) VCH1240
C JACB ASSY [VWV1917]

SEMICONDUCTORS
RESISTORS
R330, R331, R334, R335 RN1/16SE1001D
IC401, IC501 DSD1702EG R340, R341, R344, R345 RN1/16SE1001D
IC701 LA73054 R301 RN1/16SE1602D
IC302IC305, IC402, IC502 NJM5532MD R310, R311, R320, R321 RN1/16SE2000D
> IC102 NJM78M05FA R410, R420, R510, R520 RN1/16SE2201D
> IC101 NJM78M08FA
E
R332, R333, R342, R343 RN1/16SE3001D
IC301 PCM1738EG-3 R411, R418, R421, R427, R511 RN1/16SE8201D
> IC702 PQ05RD11 R518, R521, R527 RN1/16SE8201D
IC201 TC74VHC157F R1101 RS1/10S0R0J
IC202 TC7SH08F R751, R752, R754, R755 RS1/16S75R0F
IC203 TC7SHU04F
R757R761 RS1/16S75R0F
Q312, Q322, Q432, Q532, Q534 2SA1037K Other Resistors RS1/16S###J
Q601, Q701, Q801, Q802 2SC2412K
Q350Q352, Q360Q362, Q410 2SD2114K
Q420, Q510, Q520 2SD2114K
OTHERS
CN705 SOCKET AKP7012
Q201, Q310, Q311, Q320, Q321 DTC114YK
JA602 OPT. LINK OUT GP1FA502TZ
F JA801, JA802 JACK RKN1004
Q430, Q431, Q530, Q531, Q533 DTC114YK
PCB BINDER VEF1040
D701D713, D801, D802 1SS355
JA302 JACK VKB1125
D380 UDZS6.2B
JA301 JACK VKB1133

64 DV-757Ai
1 2 3 4
5 6 7 8
JA703 JACK VKB1135
JA702 JACK VKB1151 C372, C380, C401 (C= 100) VCH1237
JA601 JACK VKB1160 C410, C416 (C= 100) VCH1237 A
CN702 19P CONNECTOR VKN1250 C420, C501, C510 (C= 100) VCH1237
C516, C520 (C= 100) VCH1237
CN101 21P CONNECTOR VKN1252 C107, C109, C201 (C= 330) VCH1239
CN801 7P CONNECTOR VKN1267 C301, C303 (C= 330) VCH1239
CN102 19P CONNECTOR VKN1775 C402, C502 (C= 330) VCH1239
KN101 EARTH METAL FITTING VNF1084 C305, C306, C405, C505 (C= 47) VCH1240
KN102 EARTH METAL FITTING VNF1084 RESISTORS

R330, R331, R334, R335 RN1/16SE1001D
C JACB ASSY [VWV1919]

SEMICONDUCTORS
R340, R341, R344, R345
R301
R310, R311, R320, R321
RN1/16SE1001D
RN1/16SE1602D
RN1/16SE2000D B
IC401, IC501 DSD1702EG R410, R420, R510, R520 RN1/16SE2201D
IC701 LA73054
IC302IC305, IC402, IC502 NJM5532MD R332, R333, R342, R343 RN1/16SE3001D
> IC102 NJM78M05FA R411, R418, R421, R427, R511 RN1/16SE8201D
> IC101 NJM78M08FA R518, R521, R527 RN1/16SE8201D
R1101 RS1/10S0R0J
IC301 PCM1738EG-3 R751, R752, R754, R755 RS1/16S75R0F
> IC702 PQ05RD11
IC201 TC74VHC157F R757R761, R764R766 RS1/16S75R0F
IC202 TC7SH08F Other Resistors RS1/16S###J
IC203 TC7SHU04F
OTHERS
Q312, Q322, Q432, Q532, Q534 2SA1037K CN705 SOCKET AKP7012 C
Q601, Q801, Q802 2SC2412K CN703 SOCKET(14P) AKP7137
Q350, Q351, Q360, Q361, Q410 2SD2114K JA602 OPT. LINK OUT GP1FA502TZ
Q420, Q510, Q520 2SD2114K JA801, JA802 JACK RKN1004
Q201, Q310, Q311, Q320, Q321 DTC114YK PCB BINDER VEF1040
Q430, Q431, Q530, Q531, Q533 DTC114YK JA302 JACK VKB1125

D701D712, D801, D802 1SS355 JA301 JACK VKB1133
D380 UDZS6.2B JA703 JACK VKB1135
JA702 JACK VKB1151
COILS AND FILTERS JA601 JACK VKB1160
L701L704 CHIP BEADS VTL1089
CAPACITORS CN701 30P CONNECTOR VKN1261 D
C307, C406, C506 CCSRCH331J50 CN801 7P CONNECTOR VKN1267
C115, C116, C118C120, C801 CCSRCH470J50 CN102 19P CONNECTOR VKN1775
C702, C721 CEAT101M16 KN101 EARTH METAL FITTING VNF1084
C701, C741, C742, C751, C753 CEAT102M6R3
C761, C771 CEAT102M6R3 KN102 EARTH METAL FITTING VNF1084
C725, C762, C763, C772, C775

C110
C605
CEAT471M6R3
CEHAZA471M6R3
CEJQ101M16
D SACDB ASSY [VWG2353]
SEMICONDUCTORS
C604 CEJQ1R0M50 > IC906 BA25BC0FP
C411, C421, C511, C521 CKSRYB272K50 IC901 CXD2753R
IC902 HY57V161610DTC-8
E
C117, C407, C413, C423, C507 CKSRYF104Z25 > IC808 MM1561JF
C513, C523, C704, C711C716 CKSRYF104Z25 IC904 TC7SH00FU
C752, C754, C803 CKSRYF104Z25
C111, C112, C114, C202, C204 CKSRYF105Z10 IC806 TC7SH04FU
C302, C403, C503, C601, C606 CKSRYF105Z10 IC991 TC7SHU04F
IC905 TC7WH74FU
C703, C722C724, C726, C805 CKSRYF105Z10 IC801 XCA56367PV150
C334, C336, C344, C346 (470P) VCE1035
C330, C331, C340, C341 (4700P) VCE1046 COILS AND FILTERS
C310, C311, C320, C321 (2200P) VCE1048 L801 LCYA1R0J2520
C412, C422 (1608CH330P) VCH1226 L971L979 CHIP BEADS VTL1074
C512, C522 (1608CH330P) VCH1226 CAPACITORS F

C350, C360, C414 (C= 47) VCH1236 C903 CCSRCH100D50
C424, C514, C524 (C= 47) VCH1236 C950 CCSRCH102J50
C101, C103, C314 (C= 100) VCH1237 C931 CCSRCH470J50
C324, C338 (C= 100) VCH1237 C801, C829, C839, C840, C844 CEJQ221M6R3
DV-757Ai 65
5 6 7 8
1 2 3 4
C901, C909, C911, C922, C926 CEJQ221M6R3
SWITCHES AND RELAYS
A C944, C951 CEJQ221M6R3 S101S106 ASG7013
C828, C908, C916 CKSRYB103K50
C827 CKSRYB473K25 CAPACITORS
C807C812, C815, C816 CKSRYF105Z10
C101, C103, C107, C108, C161 CCSRCH102J50
C819C824, C826, C830C837 CKSRYF105Z10
C104 CEAL470M6R3
C100 CEJQ101M6R3
C841, C843, C902, C905C907 CKSRYF105Z10
C111 CKSRYB103K50
C912C915, C917C921 CKSRYF105Z10
C116 CKSRYF104Z50
C923C925, C927C930, C934 CKSRYF105Z10
C937, C938, C940, C943 CKSRYF105Z10
C102, C105, C110, C113, C115 CKSRYF105Z10
C945C947, C955, C956, C991 CKSRYF105Z10
RESISTORS
RESISTORS All Resistors RS1/16S###J
B All Resistors RS1/16S###J
OTHERS
OTHERS CN102 CONNECTOR 9P 09P-FJ
CN902 19P CONNECTOR 19R-1.25FJ IC103 REMOTE RECEIVER UNIT SPS-452L-H
PCB BINDER VEF1040 V101 FL TUBE VAW1073
CN903 13P CONNECTOR VKN1417 SPACER VEC2220
CN801 20P CONNECTOR VKN1460 CN101 17P CONNECTOR VKN1277
CN901 FFC CONNECT0R VKN1794
HOLDER VNF1122
E FLKY ASSY [VWG2358]

SEMICONDUCTORS
X101 (5MHz) VSS1142
C
IC101
IC102
PE5314B
PST3228
F KEYB ASSY [VWG2369]
SEMICONDUCTORS
Q103, Q105 2SA1602A D205 NSPB500-0008
Q104 2SC2412K D201, D203, D204 SLR-343VC
Q102 DTA124EK D211 UDZS6.2B
Q101 DTC124EK
SWITCHES AND RELAYS
S201, S202 ASG7013
SWITCHES AND RELAYS
S101S106 ASG7013
CAPACITORS
C291, C292 CKSRYB103K50
CAPACITORS
C101, C103, C107, C108, C161 CCSRCH102J50
C104 CEAL470M6R3
RESISTORS
D All Resistors RS1/16S###J
C100 CEJQ101M6R3
C111 CKSRYB103K50
C116 CKSRYF104Z50 OTHERS
CN201 CONNECTOR 9P 09R-FJ
C102, C105, C110, C113, C115 CKSRYF105Z10 CN202 CONNECTOR S2B-PH-K
RESISTORS
All Resistors RS1/16S###J G POWER SUPPLY UNIT [VWR1361]
OTHERS
OTHERS > P103 PROTECTOR(1.6A) AEK7012
CN102 CONNECTOR 9P 09P-FJ > P101 PROTECTOR(800mA) AEK7063
IC103 REMOTE RECEIVER UNIT SPS-452L-H > P102 PROTECTOR(1.6A) AEK7066
E V101 FL TUBE VAW1073 > P104 PROTECTOR(2A) AEK7067
SPACER VEC2220 > F1 FUSE(2A) REK1101
HOLDER VNF1122 H SCRB ASSY [VWV1922]

SEMICONDUCTORS
X101 (5MHz) VSS1142
IC901 MM1505XN
E FLKY ASSY [VWG2360]

IC902, IC903 MM1507XN
Q901, Q904 2SA1037K
SEMICONDUCTORS Q902, Q905 2SC2412K
D921 1SR154-400
IC101 PE5314B
IC102 PST3228
D901, D904D909, D911, D912 1SS355
Q103, Q105 2SA1602A
F D914D916 1SS355
Q104 2SC2412K
D918, D920 DA204K
Q102 DTA124EK
D917, D919 UDZS5.6B
Q101 DTC124EK
66 DV-757Ai
1 2 3 4
5 6 7 8
SWITCHES AND RELAYS RESISTORS
RY901RY905 VSR1017 R116R119, R129, R220R223 RAB4C0R0J
R335, R339, R340 RAB4C0R0J A
CAPACITORS R110, R212, R219, R256 RAB4C103J
C904, C914, C932, C933 CCSRCH221J50 R349, R350, R353, R363 RAB4C103J
C903, C910, C913, C921 CCSRCH391J50 R289, R290 RS1/16S5101F
C927 CCSRCH470J50
C929, C930, C937, C943 CEAT101M10 R281R288 RS1/16S56R0D
C946, C953 CEAT102M6R3 R206 RS1/16S6341D
Other Resistors RS1/16S###J
C901, C902, C907, C909 CKSRYF104Z25
C916, C917, C924, C925, C928 CKSRYF104Z25 OTHERS
C935, C936, C938C941, C945 CKSRYF104Z25 X201 (24.5760MHz) ASS7025
C950, C956C959 CKSRYF104Z25 CN103 07P CONNECTOR RKN1048
B
RESISTORS CN101 24P CONNECTOR VKN1428
R932, R937, R943, R950, R955 RS1/16S75R0F JA1, JA2 1394-TERMINAL VKN1800
R965 RS1/16S75R0F
Other Resistors RS1/16S###J X101 (6.14MHz) VSS1179
OTHERS
JA901, JA902 CONNECTOR VKB1157 J MSWB ASSY [VWG2390]
SWITCHES AND RELAYS
> S301 VSA1005
I ILKB ASSY [VWG2391]

SEMICONDUCTORS
CAPACITORS
> C301 (C=10000p, V= AC250V) ACG7033
IC203 BU2370FV C
IC204 NJU7093AF OTHERS
IC101 PD5787A CN301 CONNECTOR POST B2B-PH-K
IC301 TC74VHC541FT CN302 AMP U-P CONNECTOR RKP1834
IC306, IC308 TC7SH04FU
IC205, IC302, IC309 TC7SH08FU

IC201 TSB43CA43GGW
IC202 VYW2019
D261 RB501V-40
COILS AND FILTERS

L201L204 (330uH) VTH1043
D
CAPACITORS
C421, C423C425 CCSRCH101J50
C208 CCSRCH102J50
C205 CCSRCH150J50
C204 CCSRCH180J50
C283, C284 CCSRCH221J50
C411 CEV101M16
C231, C261, C270, C277 CEV470M6R3
C404 CKSQYB102K50
C403 CKSQYF105Z16
C307, C422, C426 CKSRYB102K50
E
C279 CKSRYB103K50
C206 CKSRYB104K16
C275, C278 CKSRYB105K6R3
C274 CKSRYB683K16
C152, C207, C210, C216, C219 CKSRYF104Z25
C285, C286 CKSRYF104Z25

C101, C103, C104, C151, C203 CKSRYF105Z10
C209, C211, C213C215 CKSRYF105Z10
C217, C218, C220C223, C232 CKSRYF105Z10
C262, C271C273, C276 CKSRYF105Z10
C281, C282, C301, C302, C306 CKSRYF105Z10 F

C308, C309, C402, C412 CKSRYF105Z10
C102, C202, C212, C401, C405 (150/4) VCH1195
DV-757Ai 67
5 6 7 8
1 2 3 4
6. ADJUSTMENT
6.1 ADJUSTMENT ITEMS AND LOCATION
A
Adjustment Items Adjustment Points (Mechanism Part)
[Mechanism Part] Cautions: After adjustment, adjustment screw locks with the
Screw tight.
1 Tangential and Radial Height Coarse Adjustment
2 DVD Jitter Adjustment
1 2 1 2
3 Initialize the Focus Sweep Setting
Tangential Radial
adjustment adjustment
screw screw
[Electrical Part]
Electrical adjustments are not required.
B
D 6.2 JIGS AND MEASURING INSTRUMENTS
Test mode remote control

Screwdriver (large) Screwdriver (medium) TV monitor unit (GGF1067)
E
Screw tight
(GYL1001)
Precise screwdriver DVD test disc

(GGV1025)
68 DV-757Ai
1 2 3 4
5 6 7 8
6.3 NECESSARY ADJUSTMENT POINTS
When Adjustment Points A

Exchange Parts of Mechanism Assy
Mechanical ~, , ! After adjustment, screw locks

Exchange the Pickup
point with the Screw tight.
Electric
point
Exchange the Traverse Mechanism

Mechanical !
point B
Electric
point
Mechanical , ! After adjustment, screw locks

Exchange the Spindle Motor point with the Screw tight.
Electric
point
C
Exchange PCB Assy
Exchange PC Board
Mechanical
point
LOAB, DVDM ASSY
Electric
point

Purpose: To set the sweep which was correct with the
individual Traverse mechanism.
Be sure to perform the following step finally when replaced

Pickup, Traverse Mechanism and Spindle Motor.
ESC CLEAR
E
GGF1067
Test mode
remote control
unit
(It is necessary when performed adjustment procedure .)
DV-757Ai 69
5 6 7 8
1 2 3 4
6.4 TEST MODE
A
TEST MODE: ON
ESC TEST
POWER
GGF1067
Test mode
ON remote control
unit
B
TEST MODE: DISC SET
CHECK
<TRAY OPEN> DVD, CD
OPEN/CLOSE DVD disc OPEN/CLOSE

(Player or Remote (Player or Remote
Control Unit) Control Unit)
DSC - &&&
C
TEST MODE: PLAY
<PLAY>
TV/LDP
An address is displayed
D
< When playback with the target address of disc (DVD)>
For example, when playback with # 30000
During PLAY +10 3 0 0 0 0 CHP/TIM Press keys in order
030000
E TEST MODE: OFF
ESC
POWER
OR
GGF1067
Test mode
OFF remote control
unit
70 DV-757Ai
1 2 3 4
5 6 7 8
6.5 MECHANISM ADJUSTMENT
1 Tangential and Radial Height Coarse Adjustment
START
Cautions:
Remove the servo mechanism. Because there is not a Spacer for height adjustment in
Remove a Spacer for height adjustment adjustment after the second time, will keep it at need.
attached to the back side (shaded area) (This parts is Traverse mechanism exclusive use of a model
of the Servo Mechanism (Float Base) with for 2001 years)
nippers.
7.3mm
Servo Mechanism B
Float Base
Put a spacer between a Tangential (or Radial) adjustment
screw and Mechanism Base and turn each screw to adjust
the height. (Refer to "6.1 ADJUSTMENT ITEMS AND
LOCATION".)
Spacer for Height adjustment

Note:
Turn the Short switch to Short side when Turn a flat side
removing the Pickup Flexible Cable. into bottom
(Refer to "7.1.9 DISASSEBLY".)
C
DV-757Ai 71
5 6 7 8
1 2 3 4
2 DVD Jitter Adjustment

A Playback method of inner and outer address for the purpose is refererd to "6.4 TEST MODE". Use disc: GGV1025
Jitter indication of the monitor is refererd to "7.1.3 TEST MODE SCREEN DISPLAY".
START
Mechanism Assy
Test mode Play the DVD test disc
Play the DVD test disc Adjust the Tangential at inner track
at outer track Adjustment Screw so that (around #30000)
(around #200000) jitter becomes minimum.
J4 : Min
Mechanism Assy
Adjust the Radial

Adjustment Screw so that
jitter becomes minimum.
J4 : Min
J4 : - - - -
Player
Play the DVD test disc
at outer track
Monitor (around #200000)
Mechanism Assy
Readjust the Tangential

CHECK Adjustment Screw so that
Turn the POWER OFF in Confirm the error rate that is jitter becomes minimum.
case of NG once, and displayed "OK"
perform the adjustment NG
once again. (Example ER (av): 2.5e - 5-*OK )
J4 : Min
E
K
O
If error rate is OK, Disc playback normally.

locks a root of The measurement of block error rate
tangential and radial ESC
adjustment screws with ESC 5
the Screw tight, and
go to step ! .
Screw tight: GYL1001

Test mode end
72 DV-757Ai
1 2 3 4
5 6 7 8
3 Initialize the Focus Sweep Setting

A
Purpose: To set the sweep which was correct with the individual Traverse mechanism.
Turn on the Player
POWER ESC CLEAR
B
Note: Be sure to perform this step when replaced the Pickup or Traverse mechanism.
DV-757Ai 73
5 6 7 8
1 2 3 4
7. GENERAL INFORMATION
7.1 DIAGNOSIS
A 7.1.1 ID NUMBER AND ID DATA SETTTING
Entering the ID Number and ID Data for Players with DVD-Audio and DVD-RW
Compatibility
It is necessary with a player with DVD-audio and DVD-RW compatibility to set an individual number (ID number) and ID data. If the
number and data are not set correctly with the following procedure, operations in the future may not be guaranteed. You will find the ID
number to be set on the yellow label on the rear panel.
Important: If no yellow label is found on the rear panel, write down the specified ID number by checking it according to "How
to confirm the ID number" shown below.
The Input is Necessary When:

B Downloading FLASH-ROM is finished. (The latest version must be downloaded when a repair is made.)
"No ID Number" is displayed on the screen or FL display immediately after the power is turned on or in Stop mode.
If "No ID DATA" is displayed, the ID data must be entered.
Note:
Be sure to enter the ID number in Stop mode.
Use the service remote control (GGF1067) for operations. Only opening/closing of the tray are performed from the player.
Use Disc No. : GGV1084
How to Input the ID Number and ID Data

C 1 To enter the input mode, press ESC + STEREO in a status with 4 When the ID number has been registered, the unit enters the
no ID number set, such as after FLASH-ROM downloading. ID data input mode. (The FL display indicates "NO ID DATA.")
In this condition, place the ID data disc on the tray and close
the tray using the CLOSE key "7/0" on the player.
2 As number input is enabled when the unit enters the input [Player's ID Data Setting]
mode, input the 9-digit ID number.
(The entered number is also displayed on the FL display.)
[Player's ID Number Setting]

ID Number ? <CLEAR> Exit
2 >---------
<CLEAR> Exit
4 Insert The ID Data Disc !
D
Input ID Number !
5 While the data are being read, the message shown in the
figure at left is displayed on the screen.
(The FL display indicates "RD ID DATA.")
3 After inputting the number, press SEARCH to register the ID

number. [Player's ID Data Setting]
[Player's ID Number Setting]
E ID Number ?
> 0 0 0 0 0 0 0 0 1 OK ?
<PLAY> Compare Mode

3 <SEARCH> Enter
5 Loading The ID Data Disc !
Input ID Number !
74 DV-757Ai
1 2 3 4
5 6 7 8
6 When the ID data have been read, the data are written to the 7 When the ID data have been written to the FLASH-ROM, the
FLASH-ROM. message "Rom Write OK" is displayed on the screen.
(The FL display indicates "WR ID DATA.") (The FL display indicates "ID DATA OK.")
A
8 After confirming this message, press CLEAR to exit the input
mode.
[Player's ID Data Setting] [Player's ID Data Setting]
6 Wait Rom Writing ! 7 Rom Write OK !
8 <CLEAR> Exit
How to Confirm the ID Number

1 Press ESC + STEREO with an ID number set, and the unit
enters the ID number confirmation mode.
2 The set ID number is displayed on the screen (and on the FL

display), permitting you to confirm it.
3 To exit this mode, press CLEAR .
[Player's ID Number Setting] C

ID Number ?
2 [ 0 0 0 0 0 0 0 0 1]
Compare
>*********
3 <CLEAR> Exit
Input ID Number !
How to Clear the ID Number

1 Press ESC + STEREO with an ID number set, and the unit 3 After inputting the number, press STOP .
enters the ID number confirmation mode. Only when the entered number matches the set ID number, the
ID number is cleared and the unit exits this mode.
2 Input the same number as the ID number you have set. If the numbers do not match, you must return to step 2.
( STOP is not accepted until 9 digits are entered.)
[Player's ID Number Setting] [Player's ID Number Setting]

ID Number ? ID Number ?
[ 0 0 0 0 0 0 0 0 1] [ 0 0 0 0 0 0 0 0 1] E
Compare Compare
2 >********* > 0 0 0 0 0 0 0 0 1 OK ?
<CLEAR> Exit
<PLAY> Enter
3 <STOP> Memory Clear
Input ID Number !
Input ID Number !
DV-757Ai 75
5 6 7 8
1 2 3 4
7.1.2 SELF-DIAGNOSIS FUNCTION OF PICKUP DEFECTIVE

This unit can confirm the laser diode current value (DVD: 650nm, CD: 780nm) of pickup on the Test Mode screen.
(Press the ESC TEST keys in order on the test mode remote control unit (GGF1067) to enter the test mode.)
A
It's effective in case of the following condition.

Symptom
Indicates "No Disc" in FL display.
Player does not playback, etc..
Procedure of Self-Diagnosis
1 Enter the Test mode.
2 When diagnosing the 650nm laser diode:
Press the TEST 1 keys in order, and turn on the laser diode (It light-up for nine seconds.).
B
When diagnosing the 780nm laser diode:
Press the TEST 4 keys in order, and turn on the laser diode (It light-up for nine seconds.).
When let it turn on once again after performed 2 once,

After pressed REP.B key once
650nm: Press the TEST 1 keys in order
780nm: Press the TEST 4 keys in order
3 Confirm the indicated value of the laser diode current (LDI). (Refer to following figure.)
4 When indicated value is more than 100, pickup is defective. Replacement is necessary
C
Replace the Traverse Mechanism Assy or Pickup.
Note : When a DVD disc or a CD disc is played in the test mode, this function is effective.
Character in bold : Item name

: Information display
Laser diode current value

D
76 DV-757Ai
1 2 3 4
5 6 7 8
7.1.3 TEST MODE SCREEN DISPLAY

Display Specification of the Test Mode
2 A
Character in bold : Item name
: Information display 3
1 7
8
5 9
6 12
21 13 14
22 15
23 16
24 17
10 18 B
11 19
1 Address indication 9 Output video system [V ]

The address being traced is displayed in number. NTSC system : [NTSC]
(as for the DVD, indication of decimal number is possible.) PAL system : [PAL]
DVD : ID indication (hexadecimal number, 8 digits) Automatic setting : [AUTO]
[ ] Scart terminal output [SK ]
CD : A-TIME (min. sec.) [0 0 0 0 ] (Display only the WY model which can do the output setting
of scart terminal.)
2 Code indication of remote control unit [R ] VIDEO : [00]
In case of double code, display a 2nd code. S-VIDEO : [01] C
RGB : [02]
3 Main unit keycode indication [K ]
0 (1) Disc sensing [DSC ]
4 Background color indication [C R G B ] The type of discs loaded is displayed.
[DVD], [CD ], [VCD], [ ]
5 (1) Tracking status [TRKG ] (2) CD 1/3 beam switch [BM ]
Tracking on : [ON]
Tracking off : [OFF] - Jitter value [J ]
(2) Laser diode current value [LDI ] Make the jitter four times, and renew it in every 0.5 second.
[J4 ]
6 (1) Spindle status [SPDL ]
D
Spindle accelerator and brake, free-runnimg [A/B] = Version of the AV-1 chip / version of firmware
FG servo [FG] [AV: / ]
Rough, velocity phase servo [SRV]
Offset addition, rough, velocity phase servo [O_S] ~ Version of the FL controller [FL: ]
(2) AFB status [AFB ]
ON [ON ] ! Region setting of the player [REG: ]
OFF [OFF] Setting value : [1] to [6]
7 Mechanism (loading) position value [M ] @ Destination setting of the FL controller

Unknown : [01] or [41] [MDL: / ]
Open state : [04] Four characters in the front represent the type of model.
Close state : [08] Three characters in the back represent the destination code. E
During opening : [12] J: /J, K: /KU, /KC, /KU/KC, R: /RAM/RL/RD, LB: /LB,
During closing : [22] WY: /WY
8 Slider position [S ] # Part number of the flash ROM and system controller
CD TOC area : [IN ] [ / ]
CD active area : [CD]
$ Version of the flash ROM [V: . ]
Flash ROM size [FLSH = ]
% Revision of the system controller [S: . / ]
DV-757Ai 77
5 6 7 8
1 2 3 4
^ (1) Revision of the DVD mechanism controller

[M: / ]
(2) Part number of the GUI-ROM (OEM model)
A [GUI: ]
(3) HOST conversion [HOST: ]
* AGC setting [AGC [] ]

AGC on : [AGC-ON]
AGC off : [AGC-OFF]
[1] : RFAGC on [0] : RFAGC off
( FTS servo IC information

DSP coefficient indication [KS [ ] ]
Displays the address (four digits) of the specified coefficient
and the setting value (four digits) with [TEST] and [9] keys.
B
) Error rate indication
1 C1 error value of CD [ER C1 ]
2 C1 error value of DVD [ER ]
_ Internal operation mode of mechanism controller

[MM : ]
Internal mechanism mode (2 digits) and internal mechanism
step (2 digits) of the mechanism controller
78 DV-757Ai
1 2 3 4
5 6 7 8
7.1.4 SELF-DIAGNOSIS FUNCTION

When enter the service mode, self diagnosis mode operates with the "ESC"+"CHP/TIM" keys automatically.
1 Mechanism Error History (past eight times of error is displayed) A

Two columns of the beginning display the error status for mechanism controller.
(the details of error contents refer to "7.1.6 Error Display".)
Eight columns of the back display the count UP value (turned count up every 20msec) from the power-up.
Example) 32h =. 1 sec, BB8h =. 1 min, 2BF20h =. 1 hour
In addition, when there was error after power-up immediately (till initial setting is completed), turn the most significant bit to ON.
2 Check Item Display of Self Diagnosis Function

a) AV1 Host Bus check (possible the check only during stop) (Read & Write process of an internal specific register)
AV_1 : OK
: not yet check
: HOST BUS NG HOST bus NG
b) Bus check between AV1 SDRAM (possible the check only during stop) (Read & Write process to the SDRAM)
AV_2 : OK
: not yet check B
: AV1-SDRAM BUS NG Bus NG between AV1 and SDRAM
c) DMA transfer port check from F.E. to AV1 (during stop, possible the check only in DVD or NO DISC)
(writing from F.E to SDRAM and reading of SDRAM)
AV_3 : OK
: not yet check
: FE-AV1 DMA NG Bus NG between F.E and SDRAM installed outside of AV1
d) Video encoder (ADV) check (Read of the specific register)
VE : OK
: NG ADV, ADV register reading NG
: NG > ADV, ADV communication NG of FR to video encoder
: NG > PRO Communication NG from EBY to progressive decoder
e) DSP check (Read of the specific register)
DSP : OK
: NG DASP NG C
f) SACD check (Read of the specific register)
SACD : OK
: NG SACD NG
g) 1394 relation HOST controller check
HOST : OK
: NG HOST controller NG
h) 1394 relation Mercury CHIP check
MERC : OK
: NG Mercury CHIP NG
Display the mechanism error history and self diagnosis result by pressing the "CHP / TIM" key once again.
Afterwards press the "CHP / TIM" key with toggle and change the display.
D
Display screen of mechanism error history and self diagnosis result
(a)
(b)
(c)
(d)
1 2
(e)
(f)
(g)
(h) E
DV-757Ai 79
5 6 7 8
1 2 3 4
7.1.5 FUNCTION SPECIFICATION OF THE SERVICE MODE

FL indication of EDC / ID error (short cut function)
Indicate it in FL with the "ESC"+"CX" keys (LD remote control unit).
A
Indication is released with the "ESC" key during display.
FL indication contents
00 /00 / 01
Indicate number of the location that caused EDC and ID errors
Retry number of times at having caused ID error (error is indicated only in the occurring moment)
Retry number of times of the latest ID error in the ST system
Retry number of times at having caused EDC error (error is indicated only in the occurring moment)
B Retry number of times of the latest EDC error in the ST system
Mark: When even once causes AV1 error, lights.
Screen display of the service mode

Indicate to the screen with the "ESC"+"CHP/TIM" keys. One digit after " / " shows number of times of the retry by ID
Release the indication with the "ESC" key. Check Error which occurred in the same block in succession.
Indication contents " * " of last one digit shows the EDC Check NG Count Over.
1 ID Address " # " shows the ID Check NG Count Over.
2 DVD in playback: Error rate regular indication and exponent When " * " and " # " are not indicated, show that data were
indication rightly readable by retry process.
CD/VCD in playback indicates the number of correct frame of (b)
C1 error /5 seconds. Indicate the error information that detected with the Audio/Video
3 Self diagnosis indication Decoder. When error occurred, a history indicates the
C Indicate the self diagnosis result whether the F.E is normal. occurrence time and the occurrence reason. History is indicated
Self Check : During FE checks to past seven times.
Self Check OK : Abnormality is not found in F.E. Field in front of ":" indicates the error information of Audio/Video
Self Check Error : Abnormality is found in F.E. Decoder.
Indicate the mechanism error history and self diagnosis result (Indication information is different from Fujitsu Decoder with
by pressing the "CHP / TIM" key once again. Mitsubishi Decoder)
Afterwards press the "CHP / TIM" key with toggle and change 02 model is 656 series and 757 series is Mitsubishi model.
the display.
Indication of the mechanism error history and self diagnosis Specification for the Audio/Video Decoder (M65773FP) model
result refer to "7.1.4 self diagnosis function". of Mitsubishi
4 Error information indication of the AV decoder bit7: VLD Fatal Error detection
(a) bit6: VLD Not Fatal Error detection
When a retry occurred in reading from the disc, a history bit5: Number of Macro Block mismatch
indicates the occurrence location and the occurrence reason. bit4: Decode error
D History is indicated to past seven times. bit3: VLD Sequence Layer Fatal Error detection
Eight columns of the beginning show the physical address bit2: VLD Picture Layer Fatal Error detection
which occurred of retry. bit1: VLD Slice Layer Fatal Error detection
As for four columns of next, bitmap indicates EDC status. LSB bit0: Start-up Sequence Time-out Error detection
shows the first sector during a block and MSB shows a last Following field in " : " indicates a value of STC (System Time
sector. Clock) which detected the above Audio/Video Decoder error.
Following field indicates the retry number of times.
One digit in front of " / " shows number of times of the retry by When often perform the switch of debug screen, an error history
EDC Error which occurred in the same block in succession. will be increased.
As for this, CPU power is used for update of OSD drawing,
symptoms occur so that control of VBR Buffer is not in time.
Indication contents
E
1
2
3
4 4
(a) (b)
80 DV-757Ai
1 2 3 4
5 6 7 8
7.1.6 ERROR DISPLAY

Error codes that are displayed on the FL display without using the remote control unit
FL Display Possible causes Operation of the unit A
The sound may not out with
AV1 VER AV-1 chip is not a match with the program of system controller
the specific audio.
CPU AERR CPU address error (Hardware is unusual.) No operation
DMA AERR DMA address error (Hardware is unusual.) No operation
Difference in versions of the internal ROM of the system controller and of the flash
FLASH ID No operation
ROM, or bus line failure or reverse installation
FLASH WRP Write protect error of the flash ROM No operation
Difference in part number of the flash ROM (When the ROM which could't be used
FLASH SIG No operation
was used.)
Check sum error of the flash ROM (It exceeds the regular size.) or reverse installation
FLASH SUM No operation
(Hardware is unusual.)
B
FLASH SIZ Size error of the flash ROM (Use 4 or 8 M-bit.) No operation
GUI ROM ERROR Difference in version of GUI ROM and system controller software. Operate as the OSD model
The system controller fetched a code other than an operation code (Hardware is
ILLGAL No operation
unusual.)
Difference in version of the internal ROM of the mechanism controller and of the flash
MECHA CPU No operation
ROM.
RESERVE Undefined interrupt (Hardware is unusual.) No operation
SLOT Inappropriate slot command issued (Hardware is unusual.) No operation
Error codes that are displayed on the FL display by using the remote control unit
(Mechanism controller error)
To display: ESC + DISPLAY + DISPLAY; Location of the display: At the two digits of center of the FL display C
To display the error history: ESC + DISPLAY + One shot; Location of the display: TV screen
Description of
FL Causes if with a DVD Causes if with a CD Operation of the Unit
Error
Search could not be complete within 7
Search could not be complete within 7
11 Search timeout seconds, and it could not enter the target CD : Stops,
seconds. DVD: Continues operation
area within 7 seconds by VCD scan.
More beyond the target while the read-in search was converging. A search could not
12 Search retry be completed after 3 retries while the unit was tracing 11 tracks. A search could not CD: Stops,
error DVD: Continues operation
be completed after retry when timeout occurs at read-in.
19 Tracing timeout Timeout (10.5 seconds) while tracing at Stop

while converging the stage of convergence of a search.
D
During Track (Index) Search, the search
for the beginning of a program could not
1B Index 0 search be completed within 3 seconds (20 Stop
error seconds in the case of Index Search)
after positioning based on the TOC data
was completed.
Embossment 1. In wobble nothing (error
plunge error distinction) : search to
1C (only a model Plunged into unreadable embossment of address 2E400h
corresponding to DVD-RW player. 2. In wobble existence:
RW) Tray open
Timeout of slider
22 inner Inside switch could not ON within 3 seconds. Stop
circumference E
Timeout of slider
23 outer Inside switch could not OFF within the following times: Stop
circumference at ATB: 2 seconds, at Backup: 2 or 2.02 seconds.
Adjusts focus at the innermost

circumference and tries to
return to its position where the
33 No FOK pulse error was generated (for 3
When the focus was deviated continuously 20 times.
during playback times),then opens.
If the same error persists after
one retry, the tray opens. (No
FOK pulse)
Were not able to playback from the disc distinction process.
38 Disc-type- PLAY or STOP was not completed by backup operation of the disc distinction. Open
sensing error Distinguished it from the blank disc in the ATB process completion. F
DV-757Ai 81
5 6 7 8
1 2 3 4
Description of
Error
A
39 SGC converge SGC could not converge during detects the peak Open
timeout
41 Spindle timeout The unit did not enter Stop mode within 10 seconds of issuance of a Stop command. Stop
Disc distinction is not completed even if passes for 10 seconds after the spindle turned.
Did not reach to the rotating speed that ATB was
possible for less than 10 seconds. Did not reach aim
48 Spindle FG transition CAV lock speed (high: 10%, low: 50%) for less than 10 Stops. (FG timeout)
timeout seconds. CAV process passed more than 5 seconds or
abnormal speed was detected. Spindle does not lock for
less than 3 seconds in the BCA read start or end.
Stops.
49 Spindle PLL CAV process passed more than 5 seconds. Abnormal speed was detected. ("73" is displayed during
transition timeout starting process.)
Stops.
B 4A Spindle lock timeout Spindle could not lock more than 1.5 seconds before start the AFB. ("73" is displayed during
starting process.)
Auto sequence
ABUSY did not return within 1 second after the DDTCT
51 timeout of peak (peak detection) command was sent. Stop
detection
Auto sequence ABUSY did not return within 30 mS after the FJMPD
52 timeout of focus Open
(Focus jump 1 to 0) command was sent.
jump down
Auto sequence
ABUSY did not return within 30 mS after the FJMPU
53 timeout of focus Open
jump up (Focus jump 0 to 1) command was sent.
54 Auto sequence ABUSY did not return within 50 mS after the GSUMON Stop
timeout of play AGC (play-AGC-measuring) command was sent.
C Auto sequence
55 timeout of disc-type- ABUSY did not return within 2 seconds after the Stop
DJSRT (disc-sensing) command was sent.
sensing
ABUSY did not return within 1 second after the
56 Auto sequence TBLOFS (Internal ATB after the completion of external Stop
timeout of ATB2 ATB) command was sent.
Auto sequence ABUSY did not return within 0.5 sec. after the TSON
57 timeout of tracking Stop
(tracking servo ON) command was sent.
servo ON
58 Auto sequence ABUSY did not return within 0.2 sec. after the TBL Stop
timeout of ATB1 (external ATB) command was sent.
Auto sequence
59 timeout of focus gain ABUSY did not return within 2 seconds after the FGN Stop
(focus gain adjustment) command was sent.
adjustment
D
Auto sequence ABUSY did not return within 2 seconds after TGN
5A timeout of tracking Stop
(tracking gain adjustment) command was sent.
gain adjustment
Auto sequence ABUSY did not return within 1 second after the AVE
5B timeout of offset Stop
(offset adjustment) command was sent.
adjustment
Auto sequence
timeout of ABUSY did not return within 200 mS after the ADJMIR
5C modulation factor Stop
(modulation factor measurement) command was sent.
measurement
Auto sequence
5D timeout of auto focus ABUSY did not return within 2 seconds after the AFB Stop
bias (auto focus bias) command was sent.
E A command could not be sent because ABUSY was
5F Auto sequence low. ABUSY did not return within 200 mS after TLV Stop
already busy command was sent.
Pause mode could not be restored within three retries
62 Pause retry error Continues operation
after it had been released.
71 ID reading check An ID could not be read for 1 second or more. Stop

during playback
Subcode check
No frame could be read for 3
72 failure during Stop
playback seconds or more.
73 ID can not read An ID could not be read within 1 second after the AFB Opens
during startup tracking on. (ID readout failure)
82 DV-757Ai
1 2 3 4
5 6 7 8
Description of
Error
Subcode could not be read within 1 Opens (Subcode readout
74 Subcode check A
failure during startup second after the tracking on. failure).
A command could not be issued to DSP because
Communication Command Busy (XCBUSY) was in force
A1 timeout of DSP (XCBUSY = L) for a specified time (about 200 Open
command S).
Command Busy (XCBUSY) was in force for a
Communication specified time (about 200 S) before and after a
A2 timeout for reading coefficient read command was issued to DSP, or Open
DSP coefficient the address echo-back after command issuance
did not match the setup address.
Communication Command Busy (XCBUSY) was in force for 200
S during continuous coefficient writing, or before
A4 timeout for Open
continuously writing and after a continuous write command was
DSP coefficient issued to DSP.
B
B1 Timeout error for In the backup sequence, codes could not be read for fixed time. Stops
backup
B2 Retry error for Cannot close tracking even if performs backup fixed number of times. Stops
backup
During tracing, do not restore after the runaway detection backup was performed
B3 Retry error for trace Stops
several times.
Stops (the mechanical
C3 Detection of tracking During playback, the overcurrent detection port was at L for 300 ms or more controller operates
overcurrent continuously. independently).
Turns off the power
(C5) Short-circuit test After the overcurrent detection (C3 error), furthermore the overcurrent detection port instantly (No indication on
corresponding error was at L for 300 mS or more continuously. the FL display and no
writing to flash memory)
C
The tray switch that had been Open mode was forcibly changed to a mode other
F5 Tray being pushed Closes
than Open by an external force.
(PH code nothing) When Philips
code is not readable during LD
starting, and a code was not
readable after the slider moved to Search, scan and special
FWD and REV directions slowly playback prohibition,
F6 Code reading NG each for five seconds. Playback as playback
(PRD) In the CD starting, when a CD-R (PRD mode) as it is.
subcode of TOC part was not
readable, but the subcode of the
program area was readable.
Loading or unloading could not be completed
within a specified time (about 10 seconds). Reverses the loading
F8 Loading timeout Though a portable cover is opening, when a direction. It timeout is D
close command was issued from the system repeated upon retry, the
controller. unit stops.
Focus ON sequence could not be completed more
than two seconds. Stops wherever possible
FC Focus Auto sequence command was finished, actually then opens (stops in the
focus ON was not completed. case of side B).
Focus did not enter even if retried it eight times.
Error codes that are displayed on the FL display by using the remote control unit (Device error)
To display: ESC + DISPLAY + DISPLAY; Location of the display: At the two digits of left of the FL display
E
FL Description of Error Causes if with a DVD Causes if with a CD Operation of the Unit
Mechanism controller RAM
bit4=1 10 etc.
check sum error
AV1 access error No operation or it becomes debugging
bit3=1 08 etc.
(read, write NG) indication if the power is able to ON.
bit2=1 04 etc. LSI11 access error
bit0=1 01 etc. SRAM access error
DV-757Ai 83
5 6 7 8
1 2 3 4
7.1.7 TEST POINTS LOCATION & WAVEFORMS

SIDE A SIDE A
15 18 Y Y 14
A
16 19 Pb C 13
17 20 Pr V 12 B DVDM ASSY
R963 R964 CN901
R996
R948 R933
CN401
C933 C931
R959
R945
R957
R958
Q934 Q932
R960
R940
C932
Q933
R947
R944
CN551
B
IC801
16MDSP
CN103
16MEBY
C 22/24M
22/24AV1
C480 R492
R485 R491
CN111
R476
R474
C484
R475
2 RFO RFO
R473
FE TE
C476
R489 IC481
R490
4 TE
R481
CN114
C471
C 27M
27MAV1
R488
IC201
D 27MDSP
IC302
33MSACD
33MEBY1
CN115
36MEBY
R261
R262
IC261
R263
R264
FPWM R266
VPWM C266
FPWM 8
PPWM
RPWM
VPWM 9
PPWM 10
E
RPWM 11
CN531
IC601
CN402
CN502
84 DV-757Ai
1 2 3 4
5 6 7 8
WAVEFORMS
Note : The encircled numbers denote measuring point in the schematic diagram.
A
B DVDM ASSY
Measurement condition : No. 2, 4 and 8 to 11 : MJK1, Title 1-chp 1 No. 12 to 14 : DVD-REF-A1, T2-Chap.1
No. 15 to 20 : DVD-REF-A1, T2-Chap.19
Foot of R963 (C) Foot of R958 (Pb)
B
Q106-emitter (RFO) Foot of R261 (FPWM) Foot of R960 (Y) Foot of R957 (Pr)
AC mode
GND
GND
Foot of R262 (VPWM) Foot of R959 (Y)

GND
IC101-pin 42 (Tracking Error) Foot of R263 (PPWM) Foot of R958 (Pb)

4 (AI-Inner Tracking Off)
10 V: 1V/div. H: 0.2msec/div.
V: 500mV/div. H: 2msec/div.
AC mode
D
GND
GND
Foot of R264 (RPWM) Foot of R957 (Pr)

GND
E
Foot of R964 (V) Foot of R959 (Y)

DV-757Ai 85
5 6 7 8
1 2 3 4
7.1.8 TROUBLE SHOOTING

START Tact-switches are damaged. (incase of only a key NG)
Power ON FLKY IC101-pin 22 is it around +1.2V when you pushed a POWER key?
A Wireless remote controller receiver or IR signal line or SEL IR signal line is damaged.
(incase of only a key of wireless remote controller NG)
Does FLKB IC101-pin 17 (SEL IR) and IR and SEL IR signal lines change 0V3.3V
when you pushed a wireless remote controller key?
Blow out fuse of the primary side
As for P-CONT of POWER SUPPLY Unit is around 3.3V. Blow out micro-fuse on the
POWER SUPPLY Unit. (Check the each voltage.)
P101P102 or POWER SUPPLY Unit is damaged.
FL controller IC (IC101) or RESET IC (IC102) on the FLKY Assy is damaged.
Are IC101-pin 12 (XRESET) and pin 11 (POWER ON) "H" level together?
Turn on the power again

B after 2 - 3 minutes.
Check the following connections :
POWER SUPPLY Unit - DVDM Assy
DVDM Assy - JACB Assy
DVDM Assy - FLKY Assy
Check each voltage regulators of DVDM Assy :
No
Is FL turn on ? IC791-pin 1 (+1.8V), IC404-pin 4 (+3.3V), IC402-pin 1 (+5V), IC403 (+2.5V)
Check each voltage (EV+6V, EV+4V, SW+3.3V, +12V, -28V, FLDC+ and FLDC-)
(If above voltage are not supplied, check the micro-fuse P101P104.)
Yes
Are not there short and open-circuit between output connector of POWER SUPPLY
Unit and CN401 of DVDM Assy?
R103 of POWER SUPPLY Unit is damaged. No -28V voltage appear.
C Short or open the zenner diode on the POWER

SUPPLY Unit. (D302)
Check the address bus and data bus of signal
Is the indication No interface between FR CPU (IC601)AV1 (IC751),
FL indication is dark or flickers.
of FL normal ? Eby-Chip (IC701) and Servo DSP (IC201).
Check each voltage regulators of DVDM Assy :
Yes IC404 (+3.3V) and IC403 (+2.5V)
Clock generator IC481 or crystal resonator X481 is damaged.

Check waveform of each pin whether IC481 does oscillation.
D Indicates the error message Refer to the section "7.1.6 ERROR DISPLAY".
Blow out micro-fuse on the POWER SUPPLY Unit.

(P101 and P102)
Check the following connections :

No DVDM Assy (CN103)- LOAB Assy (5P connector assy)
Is tray open ? DVDM Assy CN105-pin 12 (INSIDE SW signal)
Check the loading drive signal : IC351-pin 14, 15, 16
Yes Check the +6V and +12V power supply voltage
E (If above voltage is not supplied, check the micro-fuse P101 and P102.)
86 DV-757Ai
1 2 3 4
5 6 7 8
Check the following connections and drive IC :

Carriage does DVDM Assy CN104 (4P flexible cable)
not move. No Check the Stepping motor signals, IC351-pin 31, 32, 34, 35 and IC601-pin 47, 48.
(Stepping positioning) Check the +6V and +12V power supply voltage
(If above voltage is not supplied, check the micro-fuse P101 and P102.)
Yes
Check the following connection, IC351, IC101, IC201 :
DVDM Assy CN101 - Pickup Assy (26P flexible cable)
IC351-pin 9, 10, IC101-pin41 and IC201-pin 32, 47 for Focus Drive
Check the +6V and +12V power supply voltage and SW+5V
(If +6V voltage is not supplied, check the micro-fuse P101 and P102.) B
Laser diode Check it whether the pickup is defectiveness.
No
does not light.
Focus does Perform the section "7.1.2 SELF-DIAGNOSIS FUNCTION OF PICKUP DEFECTIVE"
not in. and check the LD current value.
C101 (for DVD LD) and C103 (for CD LD) of DVDM are missing.
Yes Regarding DVD LD (650nm) :
Check each signals of CN101-pin 1 (MPD), pin 2 (LD Drive), IC101-pin 15 and Q101
Regarding CD LD (780nm) :
Check each signals of CN101-pin 1 (MPD), pin 7 (LD Drive), IC101-pin 17 and Q102
MPD: Monitor Power Diode (signal output)
Check the following connections and drive IC : C

DVDM Assy CN105 (12P flexible cable)
Spindle No
Check the Spindle motor signals and IC251-each pins.
does not turn.
Check the +6V and +12V power supply voltage
(If above voltage is not supplied, check the micro-fuse P101 and P102.)
Yes
Check the connection between JACB Assy and DVDM Assy.

Check voltage regulator of JACB Assy IC701-pin 2 (+5V) for Video circuit,
IC102 (+8V, +5V) for Audio circuit.
Do the video and Check the interface of 16M SDRAM (IC741) for Eby-chip (IC701) and 64M SDRAM
sound come on? No (IC781) for AV1 (IC751).
or beeing damaged? Check digital data of video and audio signals (audio signals: 3 line data, video signals:
(noisy) 8bit data) shown to each schematic diagram and an analog signal line. D
In addition, check CLK.
Yes audio system: 22/24MHz, video system: 27MHz
Indicate the error message. Refer to the section "7.1.6 ERROR DISPLAY".
OK
DV-757Ai 87
5 6 7 8
1 2 3 4
7.1.9 DISASSEMBLY
DIAGNOSIS OF PCBs
Note :
A
When diagnosing the unit, be sure to use two Extension cables for service (Part No. : GGF1157, GGD1298)
and a Extension Board for service (Part No. : GGF1430).
1 Bonnet and Tray Panel 3 Front Panel

1 Remove the Bonnet (Screws 5). 1 Remove three Earth Lead Units (Screws 3).
2 Turn power ON. 2 Unhook ( 6).
3 Open the Tray (0). 3 Remove the Front Panel.
4 Remove the Tray Panel.
B
1 1 2
3
2 1 2 2
2 Front Panel
2
4
2 2
C
3
Tray
Tray Panel
3
4 ILKB Assy
2 Test Disc Set 1 Remove five screws.
D 1 Set the Test Disc. 2 Release two Flexible Cables.
2 Close the Tray (0). Clamp the Test Disc. 3 Remove the ILKB Assy.
3 Turn power OFF.

4 Pull out the Power Cord from the outlet.
1
4
3
3
2 1
2
E 1
ILKB Assy
2
Test Disc
2
88 DV-757Ai
1 2 3 4
5 6 7 8
5 DVDM Assy
1 Release five Flexible Cables.
A
PCB Support
2 Release from two PCB Supports.
3 Remove the DVDM Assy. 2
1
Cutting Pliers 1
1
1 3
1
DVDM Assy
6 Diagnosis
1 Stand the DVDM Assy as figure below.
2 Connect two Extension Cables for Service and a Extension Board for Service as figure below.
SCRB Assy C
Loading Mecha Assy 17P Extension Cable 21P Extension Cable

for Service for Service
[GGF1157] [GGD1298]
POWER SUPPLY Unit
CN561
MSWB Assy
CN402 1
D
CN101
JACB Assy
KEYB Assy
SACDB Assy
DVDM Assy
FLKY Assy E
Extension Board for Service

[GGF1430]
Diagnosis
DV-757Ai 89
5 6 7 8
1 2 3 4
Connection Diagram of Housing Assy
A At the time of re-assembly, connect each wire rod justly.

AC Inlet Assy CN1
Housing Assy CN2
AC Inlet Assy
CN1
CN2
POWER SUPPLY Unit
Housing Assy (2P)

VKP2278
D
CN302
MSWB Assy
FRONT side
90 DV-757Ai
1 2 3 4
5 6 7 8
Diagnosis Method of Audio Block
How to diagnose each audio signal of DVDM Assy without installing the SACDB Assy A
Do not connectes between CN502 CN801 , CN531 CN901 of FFCs.
(DVDM) (SACDB) (DVDM) (SACDB)
1 Connect pin 9 of CN502 (DSP ICM) on the DVDM Assy to GND.
B DVDM ASSY
Front Side R633 BAR CODE R714
R640
R695
R623
R693
R611
R627
C615
R615
R669
R620
C613
B
R538
R668 C610 C745
R651
AWX8156- VWS1534-
C607 R641
VWS15 - VWS1533-
R655
R662
C662
SIDE A
R647 R602
R606 R605
R607 R635
VWS1539- VWS1532-
VWS1535- VWS1531-
R531
R533
R535
R536
C657
R741
C658 R537
R676
R666 C666
R417
R412
R539
R540
R411
94V-0 R652 C532
C605
R414
C426
R413
R409
R619 176 R441
45 R534
HCT163 1 44 CN531 SACD
KN1
C531
R408
R663
R418
R661
40 R410
C534
R667 2
R664
C604 40 2
IC601
C603
FL
CN502
1
R593
R598 20
20 22
C667 R592 R590 39
39 1
1 CN402
CN502
DSP 19
19 1 1 C533 1 17
17
R599 CONTACT SIDE CONTACT SIDE
(SECOND)
CONTACT SIDE
SIDE A
pin 9
(DSP ICM) 1 Connect to GND
11
R133
R132
C115
R122
C
2 Short-circuit R581 and R582 by lead wire.
27
28
IC781
C789
IC304
33
1
B DVDM ASSY
R499 IC306 R321
34 44 IC305 IC303
IC491
R336
C322
D303
4
4
C493
3
1 C328 3
R315
C490
C495
3 1
4 5
4 5
C310
C329
3
D302
C488
C323
R581
R581
C714
C708
R719
R723
R496
Front Side Short-circuit R582
1
5
5
R498 R792 R320 C336 R330
R582
R711
R710
R720
C717
C716
R793 C723 C320
C725
R794 C724 R708 R334
C705
R707
R796
C721
C719
R797
R709
C736
R799
208 157
156
R702
C710
R677
1
SIDE B R703
D
C709
C707
C706
R712
R715
C704
C735
52
105
C713 53 104
C715 C718
C720
R722
C742 C712 C743 C744 C727
C741
C722
1
25
R595
R727
CN542
IC741
26 1
50
C747
7 CN412 1
C746
2 E
CONTACT SIDE R597
3 To confirm the Front L/R ch,

set "Audio Output Mode" of "Speakers" in "The Initial Settings Menu" to "2 channel", and playback the disc.
4 To confirm the Surround Ls/Rs ch and Center/Subwoofer ch,

turn the above setting into "5.1 channel", and playback the disc (Ls/Rs and Center/Subwoofer signals are recorded).
DV-757Ai 91
5 6 7 8
1 2 3 4
How to diagnose the SACD and DSP blocks of the SACDB Assy
A
1 Remove a Board to Board connector CN102 CN902 .
(JACB) (SACDB)
2 styling like figure below.
CN902
JACB Assy
Insulation Sheet
SACDB Assy
DVDM Assy
3 In this case an audio of SACD is not output from the Audio jack.
However, observe the signal waveform of CN902 on the SACDB Assy, and can confirm it.
CN902 - pin 2 (SACDSL), pin 4 (DSDBCK), pin 6 (DSD R), pin 8 (DSD L),
C
pin 10 (DSD Rs), pin 12 (DSD Ls), pin 14 (DSD LFE), pin 16 (DSD C).
D SACDB ASSY SIDE B

R979
R978
R977
R976
R975
R974
R973
R972
R971
R828
R830
R832
R834
R967
R951
R968
R955
R980
R982
R957
R959
R961
R800
R914
C979
C978
R840
R952
R953
R956
R981
R983
R958
R960
R962
R984
R985
R986
R987
R964
R965
R966
R824
C910
D
R801
R827
R829
R831
R833
R841
R842
R843
C991
R839
R925
5
C932
C952
IC991
R856 1
R846
R991
R848
R901
R845 C931
R929
R844 R918 R998
R992
R999
C908
R919
R913
R808
R855
R807 9 9 9
18.DSDMCK
16.DSD C
14.DSD LFE
12.DSD LS
10.DSD RS
R854
8.DSD L
6.DSD R
4.DSDBCK
2.SACDSL
8 8 8
7 7 7
R815
R847
R819
R817
R816
R818
R806 6 6 6
5 5 5
DSADML
DSADMR
E C950 4 4 4
3 3 3
2 2 2
CN902 R941
8 1 1 1
19 1 2 0 0 0
VWG
R942 AWX
R943
R949
R948
R947
R946
R945
R944
pin 2 (SACDSL)
pin 4 (DSDBCK)
pin 16 (DSD C) pin 6 (DSD R)
pin 14 (DSD LFE) pin 8 (DSD L)
pin 12 (DSD Ls) pin 10 (DSD Rs)
F
92 DV-757Ai
1 2 3 4
5 6 7 8
Disassembly of the Traverse Mechanism Assy and the Pickup Assy

1 Loading Mecha Assy 2 Tray
A
1 Remove five Screws. 1 Remove the Bridge (Screw 2).
2 Turn the Short SW to short side. 2 Pull out the Tray and remove it while unhooking a hook.
3 Remove three Flexible Cables and a Connector.
Rear View
1 -1
1 -1
2 -1
1 -2
B
Hook
Short Open
DVDM Assy 2
Side
Short SW
2 -2
1 1
C
1
1
3 4 Caution in the Tray Insertion

1
In the Tray insertion, insert it after matching a triangle mark
of the Loading Base and a position of pin of the Drive Cam.
Triangle Mark Loading Base

Loading Mecha Assy
D
DVDM Assy
Pin Drive Cam
DV-757Ai 93
5 6 7 8
1 2 3 4
3 Traverse Mechanism Assy-S and Pickup Assy-S
A
1 Remove four screws.
2 Remove the Mechanism Holder.
1 4
Mechanism Holder
B
2
Bottom View
3 Remove the FFC Holder with the state which Flexible Cable
was atatched. (Screw 1)
Cautions :
Screw is locked with Silicone Adhesive.
Please lock it with Silicone Adhesive when installs it.
D Traverse
Mechanism Assy-S Silicone
3 -1 Adhesuve
GEM1037
4 When Removing The Traverse Mechanism Assy :

3 -2 Unclamp the Flexible Cable. (2)
E
FFC Holder
Bottom View
94 DV-757Ai
1 2 3 4
5 6 7 8
Mechanism Assy
Pickup Assy 6 Remove two Skew Screws and two Skew Springs.
7 Remove the Pickup Assy-S.

A
Traverse
7
When Removing The Traverse Mechanism Assy
6
Skew Pickup Assy-S
Screw
5 Remove the Pickup Flexible Cable
Unhook ( 4)
6
6 Skew
Spring Skew
7 Remove the Traverse Mechanism Assy-S
Skew
Screw
6 2 Spring
7
6 2
Traverse Mechanism
Assy-S
C
Exchange
8 Remove two screws.

Cautions:
When Removing The Pickup Assy Screw is locked with Silicone adhesive.
Please lock it with Silicone adhesive when installs it.
5 Remove the Pickup Flexible Cable.
8 Silicone Adhesive
GEM1037 D
Slider
Hold Spring
Pickup Assy
Traverse Mechanism E
Assy-S Joint
Silicone Adhesive
8 GEM1037
Exchange
DV-757Ai 95
5 6 7 8
1 2 3 4
STYLING THE PICKUP FLEXIBLE CABLE
A
1 FOLD a edge of lining part of the Pickup Flexible Cable.
2 Insert the Pickup Flexible Cable in connector, and lock it surely.
Pickup Assy-S
B
2 7
1
8
Bottom View
Conducting Plane FFC Holder

Caution :
Move the Pickup to the innermost of the disc
C
3 Perform the styling as shown in figure below. 10 Lose slack
Fold position of step 6
D
1
Bottom View
2
3 Bottom View
Fold at the position

of reference line. 6 Reference line
11
55
4 12
Bottom View
Bottom View
F
96 DV-757Ai
1 2 3 4
5 6 7 8
7.2 IC
The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams.
A
List of IC
LA9704W, LC78652W, BA6664FM, SM8707HV, PD6345A, M65776AFP, PCM1738EG-3, DSD1702EG, LA73054,
CXD2753R, PE5314B, PE5286A, PD0274A, ADV7300AKST, PM0033A, TSB43CA43GGW, PD5787A
7 LA9704W (DVDM ASSY : IC101)

RF IC
Block Diagram
DV-757Ai 97
5 6 7 8
1 2 3 4
Pin Function
No. Pin name Pin Functions
A 1 RFN RF- input
2 VCC Power supply terminal (for DPD)
3 RFP RF+ nput
4 PD1
5 PD2
Pickup signal input
6 PD3
7 PD4
8 GND Ground (for DPD)
9 PIN1
B 10 PIN2
11 TIN1
Pickup signal input
12 TIN2
13 FIN1
14 FIN2
15 LDD1 APC1 output
16 LDS1 APC1 monitor input
17 LDD2 APC2 output
18 LDS2 APC2 monitor input
19 GND Ground (Servo system)
C
20 LDTH APC1 threshold change (H: VCC-1.5V, L: 180mV)
21 LDON Laser ON terminal (H: ON)
22 LDSEL APC change terminal (H: APC1)
23 AGOF RFAGC off terminal
24 BCA PH electric discharge coefficient change (H: BCA mode)
25 GU RF, Servo signal gain up terminal (H: Gain up)
26 DVD/CD RF- equalizer band change terminal (H: DVD)
27 DPD/TE TE output change terminal (H: DPD)
28 PP/TE TS output change terminal (H: PP)
D
29 VCC Power supply terminal (Servo system)
30 EQSCT EQ change for CD (H: 62 pin choice)
31 WO/BH BHMIX output change terminal (H: WOBLE)
32 RFSEL RF amplifier gain change (H: 6dB up)
33 LDDM LDD monitor terminal
34 TH Tracking hold (H: hold)
35 XHTR Tracking, Bottom band change (L: High bandwidth)
36 SGC Servo gain control terminal (FE, PP, TE)
37 FEBL FE balance adjustment terminal
E
38 TEBL TE balance adjustment terminal
39 CP Resistance for charge pump gain setting, a condenser connection terminal
40 THC Volume connection terminal for tracking hold
41 FE Focus error output
42 TE Tracking error output
43 PPN Ohms connection terminal for push-pull gain setting
44 PP Push-pull output terminal
98 DV-757Ai
1 2 3 4
5 6 7 8
No. Pin name Pin Functions

45 TS Tracking cross signal output A
46 TESI TES comparator input terminal
47 TES TES output
48 DEF Deffect search
49 BHMIX PH, BH, woble change output
50 BHACI BH AC input
51 BH RF bottom detection output
52 PH RF peak detection output
53 WOC Volume connection terminal for DC cut
54 ISET Ohms connection terminal for BPF center frequency setting B
55 BCAI Ohms connection terminal for peak hold detection fixed number setting (In BCA)
56 PHC PH detection condenser connection terminal for RF-AGC
57 LPC Condenser connection terminal for RF DC servo
58 DEFC Volume connection terminal for deffect search
59 GND Ground (RF system)
60 RFO RF output terminal
61 REF Reference output terminal
62 EQC1 Equalizer setting terminal for CD
63 VCC Power supply terminal (RF system)
C
64 EQC2 Equalizer setting terminal for CD
DV-757Ai 99
5 6 7 8
1 2 3 4
7 LC78652W (DVDM ASSY : IC201)

Servo DSP IC
A
Block Diagram
FE 33 47 FDO
TE 32 48 TDO
45 SLDO
TILTE 29 8bit Servo 8bit
MPX Processor 46 SPDO
A/D D/A
RF_PH 30 (1616+3232) 44 TBAL
RF_BH 31 43 TILTDO
JITT 28 42 AUXO
B
HFLIO 51 CMP
24 DRF
Track Counter 22 FAST
TES 26
PP2/EVENT 56 Event Counter

95 DVDSYEQ
FG 55 FG Counter
SLCIST1,2 34,35
EFMIN 39
SLC CLV 23 V_PB
C SLCO1,2 36,37
EFMOUT 1
PCKIST1,2 87,88
DVD Lock 21 FSEQ
DVDFR 90
Detection 77 WRQ
CDFR 91
74 SQOUT
PD01-3 83-85 Sub Code
PLL 75 CQCKB
JV 92 Frame Synchronous Decode
76 RWC
Detection, Protection, CRC
Insertion EFM 17 EMPH
DVDSYNC 96
Demodulation 12 PW
PCK 93
10 SBCK
LEFM 100 18 SBSY
D
LEFM2 97 11 SFSY
VPDO 81 For De-Interleave

Clock 16k SRAM
VCOC 80 Error Detect
9 FSX
Generator Correction
XIN 14 20 EFLG
C1-Twofold,
XOUT 15 C2-Fourfold
XTALOUT 8
ADRAO 94
5 LRSY
CSB 58
Command 4 ROMCK
WRB 60 Supplement/Mute
Interface Serial Out 3 ROMXA
RDB 59 D Attenuate
E P0-7 63-70 Deemphasis Filter 2 C2F
BUSYB 73
LASER 52 DOUT 19 DOUT
FBUSYB 7
25,27 TEST1-4
53,54 38,50
PP0-3 ,56 General Purpose Register
57 RESB
100 DV-757Ai
1 2 3 4
5 6 7 8
Pin Function
No. Pin Name I/O Pin Function
1 EFMOUT O Output the state that was binary-stated value EFM A
2 C2F O C2 flag output
3 ROMXA O CD-ROM data output
4 ROMCK O Shift clock output for CD-ROM data output
5 LRSY O L/R clock output for CD-ROM data output
6 PP3 I/O General-purpose port input/output / DVD sync. signal input N ch-OD output
7 FBUSYB O Busy signal output of DSP process operation N ch-OD output
8 XTALOUT O External system clock output
9 FSX O CD 1 frame sync. signal output
10 SBCK I Subcode reading out clock input
11 SFSY O Frame sync. signal output of subcode
12 PW O Subcode P, Q, R, S, T, U, V and W output B
13 VSS GND pin

14 XIN I Connect a crystal resonator (16.9344MHz)
15 XOUT O Connect a crystal resonator
16 DVDD1 3.3V power supply of the oscillation circuit
17 EMPH O Monitor pin of the deemphasis
18 SBSY O Sync. signal output of the subcode block
19 DOUT O Audio EIAJ data output
20 EFLG O Error correction state monitor of the error correction C1 and C2
21 FSEQ O Detection monitor of the CD/DVD frame sync. signal
22 FAST O Playback speed monitor N ch-OD output
C
23 V_PB O Monitor output of the rough servo/CLV control
24 DRF O In focus monitor
25 TEST3 I Test input 3
26 TES I Tracking error signal input
28 JITT I Jitter quantity detecting signal input of EFM PLL
29 TILTE I Tilt error signal input
30 RF_PH I RF peak hold signal input
31 RF_BH I RF bottom hold signal input
32 TE I Tracking error signal input
33 FE I Focus error signal input D
34 SLCIST1 Current setting pin 1 of the constant current charge pump for SLC
35 SLCIST2 Current setting pin 2 of the constant current charge pump for SLC
36 SLCO1 O Control output 1 for SLC
37 SLCO2 O Control output 2 for SLC
39 EFMIN I EFM/EFM + input
40 AVDD 5V power supply of A/D and D/A for servo
41 AVSS GND of A/D and D/A for servo
42 AUXO O DA auxiliary output
43 TILTDO O Tilt control signal output
E
44 TBAL O Tracking balance control signal output
45 SLDO O Sled control signal output
46 SPDO O Spindle control signal output
47 FDO O Focus control signal output
48 TDO O Tracking control signal output
49 VREF Reference level of D/A for servo
DV-757Ai 101
5 6 7 8
1 2 3 4
A 51 HFLIO I/O Mirror detection signal input/output

52 LASER O Output pin for laser ON/OFF control
53 PP0/DVD_CDB I/O General-purpose port input/output / Disc discrimination signal output
54 PP1/CRCERRB I/O General-purpose port input/output / Subcode CRC result signal output
55 FG I FG counter input
56 PP2/EVENT I/O General-purpose port input/output / Event counter input
57 RESB I Reset input
58 CSB I Chip select input
59 RDB I Internal state reading signal input
60 WRB I Command / data writing signal input
61 DVDD2 5V power supply
B 62 VSS GND
63 P0
64 P1
65 P2
66 P3
I/O Command / data input/output
67 P4
68 P5
69 P6
70 P7
71 VSS GND
72 DVDD1 3.3V power supply for internal
C
73 BUSYB O Busy signal output of command process
74 SQOUT O Serial output of subcode Q
75 CQCKB I Shift clock input for subcode Q data output
76 RWC I Update permission input of subcode Q
77 WRQ O Read out ready monitor of subcode Q
78 AVSS PLL GND for internal system clock
79 VRPFR VCO oscillation range setting of PLL for system clock
80 VCOC I
Connect a PLL filter for system clock
81 VPDO O
82 AVDD PLL 5V power supply for system clock
D 83 PDO1 I/O PLL filter connection pin 1 for EFM playback
84 PDO2 I/O PLL filter connection pin 2 for EFM playback
85 PDO3 I/O PLL filter connection pin 3 for EFM playback
86 AVSS PLL GND for EFM playback
87 PCKIST1 Current setting 1 of PLL constant current charge pump for EFM playback
88 PCKIST2 Current setting 2 of PLL constant current charge pump for EFM playback
89 AVDD PLL 5V power supply for EFM playback
90 DVDFR VCO oscillation range setting of PLL for EFM playback 1
91 CDFR VCO oscillation range setting of PLL for EFM playback 2
92 JV O Jitter output of PLL clock for EFM playback
93 PCK O Bit clock output for EFM playback
E
94 ADRAO I Address input
95 DVDSYEQ I DVD synchronize pulse input
96 DVDSYNC I DVD synchronous signal input
97 LEFM2 O Output the state that cut and out a signal which was binary-stated value EFM with PCK 2
98 DVDD1 3.3V power supply for I/O
99 VSS GND
100 LEFM O Output the state that cut and out a signal which was binary-stated value EFM with PCK 1
102 DV-757Ai
1 2 3 4
5 6 7 8
7 BA6664FM (DVDM ASSY : IC251)

Three-phase Motor Driver
A
Block Diagram
A3 2 DRIVER 28 RNF
TSD 27 VM
A2 4 GAIN
GAIN 26 GSW
CONTROL SWITCH
A1 7 Vcc
CURRENT 25 VCC
SENSE AMP
TL
24 FG
HALL AMP TORQUE
GND 8 23 PS B
PS
SENSE AMP
H1+ 9 22 EC
H1- 10 Vcc 21 ECR

Vcc
H2+ 11 20 FR
H2- 12 R 19 FG2
D Q
SHORT BRAKE 18 SB
CK Q C
H3+ 13
17 CNF
H3- 14 BRAKE MODE 16 BR
HALL BIAS 15 VH
Pin Function
No. Pin Name Pin Function No. Pin Name Pin Function
1 N.C. N.C. 16 BR Brake mode switching pin D
2 A3 Output pin 17 CNF Capacitor connection pin for phase compensation
3 N.C. N.C. 18 SB Short brake pin
4 A2 Output pin 19 FG2 FG 3-phase mix signal output pin
5 N.C. N.C. 20 FR Rotation detecting pin
6 N.C. N.C. 21 ECR Control reference pin of output voltage
7 A1 Output pin 22 EC Output voltage control pin
8 GND GND pin 23 PS Power save pin
9 H1+ 24 FG FG signal output pin
10 H1- 25 VCC Power supply pin
E
11 H2+ 26 GSW Gain switching pin
Hall signal input pins
12 H2- 27 VM Motor power pin
13 H3+ 28 RNF Resistor connection pin for output current detection
14 H3- FIN FIN GND
15 VH Hall bias pin
DV-757Ai 103
5 6 7 8
1 2 3 4
7 SM8707HV (DVDM ASSY : IC481)

Clock Generate IC
A
Pin Arrangement
Pin Function
No. Pin name Dir. Pin Functions
1 VDD1 PWR Power supply terminal 1 (digital business)
2 VSS1 GND Earth terminal 1 (digital business)
3 MO1 OUT Video output terminal 1 (the 27MHz fixed output)
4 MO2 OUT Video output terminal 2 (the 27MHz fixed output)
D 5 VDD2 PWR Power supply terminal 2 (analog business)

6 VSS2 GN D Earth terminal 2 (analog business)
7 XTI IN External clock input terminal or crystal resonator connection
8 XTO OUT Crystal resonator connection terminal
9 SO1 OUT Signal conditioning system output terminal 1 (36.8640MHz fixation)
10 AO1 OUT Sound output terminal 1 (the 512fs output)
11 VSS3 GND Earth terminal 3 (digital business)
12 VDD3 PWR Power supply terminal 3 (digital business)
Sampling frequency change terminal
E FSEL= "L": fs=48kHz
14 FSEL IN
FSEL= "H": fs=44.1kHz
(There is inside pull-up resister, Schmidt trigger input)
16 NC Unused terminal
104 DV-757Ai
1 2 3 4
5 6 7 8
7 PD6345A (DVDM ASSY : IC601)

FR CPU
A
Pin Function
No. Mark Pin Name I/O Pin Function
1 P20/D16 D0
2 P21/D17 D1
3 P22/D18 D2
4 P23/D19 D3
5 P24/D20 D4
6 P25/D21 D5
7 P26/D22 D6
8 P27/D23 D7 B
I/O Data bus input/output
9 P30/D24 D8
10 P31/D25 D9
11 P32/D26 D10
12 P33/D27 D11
13 P34/D28 D12
14 P35/D29 D13
15 P36/D30 D14
16 P37/D31 D15
17 VSS GND Ground
18 P40/A00 A0
C
19 P41/A01 A1
20 P42/A02 A2
21 P43/A03 A3
O Address bus output
22 P44/A04 A4
23 P45/A05 A5
24 P46/A06 A6
25 P47/A07 A7
26 VCC3 V+3.3D Power supply
28 P50/A08 A8
29 P51/A09 A9 D
30 P52/A10 A10
31 P53/A11 A11
O Address bus output
32 P54/A12 A12
33 P55/A13 A13
34 P56/A14 A14
35 P57/A15 A15
36 VSS GND Ground
37 P60/A16 A16
38 P61/A17 A17
39 P62/A18 A18
E
40 P63/A19 A19 O Address bus output
41 P64/A20 A20
42 P65/A21 A21
43 P66/A22 A22
44 P67/A23 WBL O For Wobble detection corresponding to DVD R/W (main)
45 DAVS GND Ground
46 DAVC V+3.3D Power supply
47 DA0 STEP1 I
For stepping motor control
48 DA1 STEP2 I
49 DA2 LODRV I Loading, door and select motor drive
F
DV-757Ai 105
5 6 7 8
1 2 3 4

50 AN0 NC I NC
A
51 AN1 NC I NC
52 AN2 NC I NC
53 AN3 XOEM I OEM model protection input
54 AN4 LDREAD I Input for LD current value indication
55 AN5 NC I NC
56 AN6 NC I NC
57 AN7 LODPOS I Loading clamp position SW input
58 AVCC V+3.3D Power supply
59 AVRH V+3.3D Power supply
60 AVSS/AVRI GND Ground
B
61 VSS GND Ground
62 PP0/ATGX SLDPOS I SW input of slider inside position
63 PP1/FRCK GSW O Gain up at ACBR (at ACBR: H, others: L)
64 PP2/IN0 780ON I ON/OFF control signal of 780nm laser diode
65 PP3/IN1 GU O RF, servo signal gain up terminal (H: Gain up)
66 PP4/IN2 XMON O Mute of DRV (spindle motor ON: H)
67 PP5/IN3 XDRVMUT O FTS driver mute output
68 PP6 LT1_3V O Communication response to the FL controller
69 PP7 XRDY_3V I Communication request from the FL controller
C 71 VCC2 V+2.5D Power supply
72 PO0/OC0 XCURDET I Actuator current detection input Servo OFF for "L" 300ms
73 PO1/OC1 XCBUSY I Busy signal of command process Command acceptable : "L"
74 PO2/OC2 XDSPRST O Servo DSP reset
75 PO3/OC3 BCA BCA read signal (at BCA read: H) (Not used)
76 PO4/OC4 NC I NC
77 PO5/OC5 PPCNT O Switch of TZC in WBL traversal (at PP: H)
78 PO6/OC6 XDFINH O Defect signal control (DEFECT ON: Hi-Z; OFF: "L")
79 PO7/OC7 DPD/TE O H=1 beam, L=3 beams
80 VSS GND Ground
81 PN0/AIN0 DVD/XCD O RF EQ switching signal at DVD/CD "H": DVD, "L": CD
D
82 PN1/BIN0 AGOFF O "H": Turn off AGC of RFIC
83 PN2/AIN1 650X780 O 780nm/650nm switching signal
84 PN3/BIN1 LD ON O ON/OFF control signal of laser diode
85 PN4/AIN2 WBLSEL O NC
86 PN5/BIN2 RFSEL O RF amplifier gain change terminal (H: Gain up)
87 PN6/AIN3 XCD2X O For VCD double speed playback
88 PN7/BIN3 OEICG O "H": Gain of OEIC up to 6dB
89 PM0/ZIN0 EN33M O NC
90 PM1/ZIN1 EN24M O NC
91 PM2/ZIN2 V SEL O (Composite, S) / (YCbCr) or (RGB) switch
E 92 PM3/ZIN3 V SEL2 O (Composite) of scart terminal / (S) switch
93 PL0/SDA1 SDAI 12C Serial 12C control lines
94 PL1/SDA0 NC NC
95 PL2/SCL1 SCLI 12C Serial 12C control lines
96 PL3/SCL0 NC NC
97 PL4 CTS I RS-232C clear to send input
98 PL5 DTR O RS-232C clear to send output
99 PL6/UC0 NC O NC
100 VSS GND Ground
106 DV-757Ai
1 2 3 4
5 6 7 8

101 PK0/TIN0 XVQERST O VQE3 reset signal A
102 PK1/TIN1 XCSPRO1 Serial communication enable of the progressive converter IC
103 PK2/TIN2 XCSVQE5 Serial communication enable of VQE5 IC
104 PK3/TIN3 EN16M O N.C.
105 PK4/TOT0 44X48 O DAC and DASP supply clock fs 44/48 selection
106 PK5/TOT1 1394XRDY I N.C.
107 PK6/TOT2 AOSEL1 O AV-1/audio DSP switch (front L/R data)
108 PK7/TOT3 P/XI O Progressive/Inter race change signal
111 PJ0/INT0 XINT0 I
B
112 PJ1/INT1 XINT1 I
113 PJ2/INT2 XIRQ10 I MY chip interrupt #0
114 PJ3/INT3 XIRQ11 I MY chip interrupt #1
115 PJ4/INT4 XABUSY I Busy signal of DSP process operation "L"
116 PJ5/INT5 THLD I Playback speed monitoring signal
117 PJ6/INT6 SBSY I Sync. signal of subcode block (period SO+SI "H")
118 PJ7/INT7 N.C. I N.C.
119 PI0/SI0 SSI I Serial bus data input
120 PI1/SO0 SSO_3V O Serial bus data output
121 PI2/SCK0 SSCK_3V I Serial bus clock input
122 PI3/SI1 RXD_3V I RS-232C RXD C
123 PI4/SO1 TXD_3V O RS-232C TXD
124 PI5/SCK1 NC O NC
125 PH0/SI2 1394LT O NC
126 PH1/SO2 DSPICM I Audio system DSP serial communication Readv signal
127 PH2/SCK2 NC I NC
128 MD0 GND
129 MD1 GND Ground
130 MD2 GND
131 VSS GND Ground
D
133 VSS GND Ground
134 X1 EXTAL O
135 X0 XTAL I
137 PC0/DREQ2 RESET1 O Audio system DSP reset
138 PC1/DACK2 XCSADSP0 O Chip select port for audio system DSP
139 PC2/DEOP2 XCSDF2 O DAC chip select (for surround system L/R)
140 PB0/DREQ0 XDREQ0 I DMA response output to BY Chip
141 PB1/DACK0 DACK0 O DMA request input from BY Chip
142 PB2/DEOP0 ENCD O N.C.
143 PB3/DREQ1 XDREQ1 I DMA response output to AV-1 Chip E
144 PB4/DACK1 XDACK1 O DMA request input from AV-1 Chip
145 PB5/DEOP1 EN_FLOW O N.C.
146 PB6/IOWRX XCOMP O RGB/color difference change of video driver
147 PB7/IORDX XCSDF3 O N.C.
148 VSS GND Ground
149 PA0/CSOX XCS20 O Chip select output to Flash ROM
150 PA1/CS1X XCS6 O AV-1 Chip select
DV-757Ai 107
5 6 7 8
1 2 3 4

151 PA2/CS2X XCS3 O Chip select of PD4995A (MY Chip)
A
152 PA3/CS3X XCS4 O Chip select of servo DSP
153 PA4/CS4X XCS23 O Chip select output to SRAM (1M)
154 PA5/CS5X N.C. O N.C.
159 NMIX V+3.3D fixed
160 HSTX V+2.5D fixed
161 INITX XINIT I
B 162 P80/RDY RDY I
163 P81/BGRNTX XAMUTE I Final stage mute of 2 ch audio output
164 P82/BRQ XMMUTE O Audio multi channel mute
165 P83/RDX XRD O
166 P84/WR0X XWR0 O
167 P85/WR1X XWR1 O
168 VSS GND Ground
169 P90/SYSCLK SYSCLK O N.C.
170 P91 DFRST DAC reset (for front L/R)
171 P92/MCLK DFRST1 DAC reset (for center, surround and LFE)
C 172 P93 XCSDF0 O DAC chip select ( XLAT3)
173 P94/LBAX XCSDF1 O DAC chip select for center, surround and LFE
174 P95/BAAX XAQRST O AQE reset
175 P96 XCSAQE O AQE chip select
176 P97/WEX TM ENT I Test mode entry
108 DV-757Ai
1 2 3 4
5 6 7 8
7 M65776AFP (DVDM ASSY : IC751)

MPEG2 Decorder IC
A
Block Diagram
DV-757Ai 109
5 6 7 8
1 2 3 4
Pin Function
A 201-208 BD [7:0] IN Bit stream data entry pin
2 BCLK IN Strobe signal of BD pin (clock)
This order effective / invalidity of data done a sample of by BD pin.
3 BDEN IN
It is done a sample with a start edge of BCLK.
4 BDREQ OUT Data demand signal
5 BSECH IN This order it whether data of BD pin are with top byte of a sector.
84-87
90-95 MD [15:0] I/O Data transfer line with SDRAM
97-102
53-55
58-63 MA [11:0] OUT Address line of SDRAM
B 65, 67, 69
66, 68 MBA [1:0] OUT SDRAM bank choice line
70 DCS
73 DCS2
74 DCS3 OUT Chip select of SDRAM
75 DCS4
76 DCS5
77 RAS OUT RAS (Row Address Strobe) control line of SDRAM
78 CAS OUT CAS (Column Address Strobe) control line of SDRAM
82 DQMU OUT DQM control line of SDRAM
C
83 DQML OUT DQM control line of SDRAM
80 DWE OUT WE control line of SDRAM
79 MCLK OUT Movement clock of SDRAM
183 PXCLK OUT 27MHz pixel clock
182 PXCLKP OUT 54MHz pixel clock
157, 158,
Digital pixel data.
184-186 PD [7:0] OUT
Y/Cb/Cr is done multiple of by 8 bit bus, and it is output.
188-192
178 CSYNC IN Composite SYNC signal input terminal
179 OSDKEY OUT OSD key flag output
D
177 PWD OUT The phase comparator output for external synchronization movement
181 HSYNC OUT Horizontal synchronizing signal output pin
180 VSYNC OUT Vertical synchronizing signal output pin
Serial PCM data for DAC
164 AO0 OUT
It output Lf/Rf data.
166 AO1 OUT
It output C/Sw data.
167 AO2 OUT
It output Ls/Rs data.
168 AOD OUT
It is for the down mixture output.
E
169 AAD OUT Anciallary data output
176 DOCLK OUT PCM bit clock
159 LRCLK OUT Clock for channel distinction of pulse code modulation audio system data (L/R)
173 DACCLK OUT Exaggerated sample movement clock of DAC
161 CDBCK IN The pulse code modulation bit clock which is input by CDDSP
160 CDLRCK IN The L/R clock which is input by CDDSP
110 DV-757Ai
1 2 3 4
5 6 7 8

163 CDDIN IN PCM audio system data which are input by CDDSP A
162 CDDATA IN Digital audio interface input
170 DOUT0 OUT Digital audio interface output
171 DOUT1 OUT Digital audio interface output
6-11
14-19 HD [15:0] I/O Data I/O pin
21-24
25, 26
29-34 HA [11:0] IN Address input pin
36-39
45 BHE IN Byte High Enable signal input pin
41 RE IN Read Enable signal input pin B
44 WE IN Write Enable signal input pin

40 CS IN Chip Select signal input pin
46 RDY OUT The acknowledge signal which shows that readout of data or a note was completed
47 INT1
48 INT2 OUT It is an interrupt request signal for outside CPU from M65776AFP
49 INT3
51 DREQ OUT DMA request signal for OSD BitMap transfer
52 DACK IN DMA acknowledge signal for OSD BitMap transfer
194, 195 HMODE [1:0] IN Host interface mode of operation setting pin C
117 IREF IN Reference electric current input pin
115 AVRI IN Reference voltage input pin
120 BIAS1
IN Bias voltage impression pin of current source
118 BIAS2
119 PAY OUT Analog electric current output pin (for Y)
116 PAB OUT Analog electric current output pin (for Pb)
122 PAR OUT Analog electric current output pin (for Pr)
114 DAOUTB OUT Be connected to an analog ground.
113, 121,
AVDD33 3.3V analog power supply D
123
124 AGND33 Analog ground
System clock input terminal
106 CLKIN IN
It input 27MHz clock.
105 CLKO OUT 27MHz clock output
172 ACLKI IN Audio system clock input terminal
193 RESET IN Hardware reset terminal
196, 197,
TEST [2:0] IN Fix it in "L" potential.
200
12, 27, 42,
56, 71, 88, E
103, 134, VDD18 1.8V power supply terminal
155, 174,
198
13, 28, 43,
57, 72, 89,
104, 135, VDD33 3.3V power supply terminal
156, 175,
199
DV-757Ai 111
5 6 7 8
1 2 3 4

A 1, 20, 35,
50, 64, 81,
96, 112, GND Ground terminal
125, 145,
165, 187
107 AVDD18 1.8V power supply terminal for inside PLL
108 AGND18 Ground terminal for inside PLL
109-111
126-133
NC0 NC
136-144
146-154
112 DV-757Ai
1 2 3 4
5 6 7 8
7 PCM1738EG-3 (JACB ASSY : IC301)

D/A Converter IC
A
Pin Arrangement Pin Function
DV-757Ai 113
5 6 7 8
1 2 3 4
7 DSD1702EG (JACB ASSY : IC401, IC501)

D/A Converter IC
A
Block Diagram
Pin Arrangement Pin Function
114 DV-757Ai
1 2 3 4
5 6 7 8
7 LA73054 (JACB ASSY : IC701)

DVD Video Amplifier
A
Block Diagram
DV-757Ai 115
5 6 7 8
1 2 3 4
Pin Function
No. Pin Functions 0 0.7V (LOW) 2.6 5V (HIGH)
A 36 AMP-GAIN change for composite/S 6 dB 9 dB
15 AMP-GAIN change for component 6 dB 9 dB
35 Drive electric current change for composite/S 2 system drive 1 system drive
19 Drive electric current change for component 2 system drive 1 system drive
Mute control for In 10 pin LOW It is not do mute 33, 31, 28 pin mute
5
composite/S In 10 pin HIGH It is not do mute 31, 28 pin mute
12 Mute control for component It is not do mute 25, 23, 21 pin mute
9 The control of Y/C MIX In composite In Y/C MIX
10 11 pin input form change In the component input In the baseband input
B 13 LPF characteristic change for component Inter race correspondence Progressive correspondence
2 pin falls to GND in Y/C-MIX.
11 pin is clamp, and the Y signal input, 14, 16 pin input a CB, CR signal into NTSC (in the component input) with pedestal clamp.
8 pin is clamp, and the Y signal input, 11, 14, 16 pin input a R, G, B signal into PAL (in the baseband input) with pedestal clamp.
It prohibit mute of 5 pin when It do Y/C-MIX in PAL (in the baseband input).
116 DV-757Ai
1 2 3 4
5 6 7 8
7 CXD2753R (SACDB ASSY : IC901)

SACD Decorder
A
Pin Arrangement
DV-757Ai 117
5 6 7 8
1 2 3 4
Pin Function
A 1 VSC - Ground terminal for core
2 XMSLAT Latched input terminal for microcomputer serial communication
3 MSCK I Shift clock input terminal for microcomputer serial communication
4 MSDAI Data entry terminal for microcomputer serial communication
5 VDC - Power supply terminal for core
6 MSDATO Data output terminal for microcomputer serial communication
7 MSREADY O Output preparation completion flag for microcomputer serial communication
8 XMSDOE Output enable terminal for microcomputer serial communication
9 XRST I Reset terminal resets the whole lC with "L".
10 SMUTE Ipd Software mute removes audio out with "L" with "H" a soft mute terminal.
11 MCKI I Master clock input terminal
B 12 VSIO - Ground terminal for I/O
13 EXCKO1 Outside output clock terminal 1
14 EXCKO2 Outside output clock terminal 2
O
15 LRCK 1Fs (44.1kHz) clock output terminal
16 FRAME Frame signal output terminal
17 VDIO - Power supply terminal for I/O
18 MNT0
19 MNT1
Monitor output terminal
20 MNT2
21 MNT3
O
22
C
23
TESTO Output terminal for test
24
25
26 TCK I It is fixation in "L" a clock input terminal for test.
27 TDI Ipu Input terminal for test
28 VSC - Ground terminal for core
29 TDO O Output terminal for test
30 TMS Input terminal for test
Ipu
31 TRST Reset terminal for test
32 TEST1
D 33 TEST2 I It is fixation in "L" a clock input terminal for test.
34 TEST3
36 TESTO Output terminal for test
37 XBIT DST connection monitor terminal
38 SUPDT0 Supplementary data output terminal (LSB)
O
39 SUPDT1
40 SUPDT2 Supplementary data output terminal
41 SUPDT3
42 VSIO - Ground terminal for I/O
43 SUPDT4
E O Supplementary data output terminal
44 SUPDT5
46 SUPDT6 Supplementary data output terminal
47 SUPDT7 O Supplementary data output terminal (MSB)
48 XSUPAK Supplementary data output terminal
50 TESTO O Output terminal for test
118 DV-757Ai
1 2 3 4
5 6 7 8

51 A
TESTI I It is fixation in "L" a test input terminal.
52
55 DSADML DSD data output terminal for Lch Down Mix
O
56 DSADMR DSD data output terminal for Rch Down Mix
57 BCKASL I Input and output choice terminal of a 1 bit clock for DSD data output.L= input (slave), H = output (master).
58 VSDSD - Ground terminal for DSD data output
59 BCKAI I Bit clock input terminal for DSD data output
60 BCKAO O Bit clock output terminal for DSD data output
61 PHREFI I Phase reference signal input terminal for DSD output phase modulation
62 PHREFO Phase reference signal output terminal for DSD output phase modulation B
63 ZDFL Zero Lch data search flag

64 DSAL O DSD data output terminal for Lch loud speaker
65 ZDFR Zero Rch data search flag
66 DSAR DSD data output terminal for Rch loud speaker
67 VDDSD - Power supply Mizuko for DSD data output
68 ZDFC Zero Cch data search flag
69 DSAC DSD data output terminal for Cch loud speaker
O
70 ZDFLFE Zero LFEch data search flag
71 DSASW DSD data output terminal for SWch loud speaker
72 VSDSD - Ground terminal for DSD data output C
73 ZDFLS Zero LSch data search flag
74 DSALS DSD data output terminal child for LSch loud speaker
O
75 ZDFRS Zero RSch data search flag
76 DSARS DSD data output terminal for RSch loud speaker
77 VDDSD - Power supply Mizuko for DSD data output
78 IOUT0 Data output terminal 0 for IEEE1394 link tip I/F
O
O
83 VDC - Power supply terminal for co D
O
87 IANCO O Transmission information data output terminal for IEEE1394 link tip I/F
88 IFULL Data transmission hold demand signal input terminal for IEEE1394 link tip I/F
I
89 IEMPTY High speed transmission demand signal input terminal for IEEE1394 link tip I/F
91 IFRM Frame reference signal output Mizuko for IEEE1394 link tip I/F
92 IOUTE O Enable signal output terminal for IEEE1394 link tip I/F
93 IBCK Data transmission clock output terminal for IEEE1394 link tip I/F
E
95 It is fixation in "H" a test input terminal.
I
96 TESTI It is fixation in "L" a test input terminal.
97 Ipu It is fixation in "H" a test input terminal.
99 VDC - Power supply terminal for co
100 TESTI I It is fixation in "L" a test input terminal.
DV-757Ai 119
5 6 7 8
1 2 3 4

A 101
102
104
105
107
109
111 WAD0 Outside A/D data entry terminal for PSP Physical Disc Mark search (LSB)
B 112 WAD1
I
113 WAD2 Outside A/D data entry terminal for PSP Physical Disc Mark search
114 WAD3
117 WAD4
118 WAD5 Outside A/D data entry terminal for PSP Physical Disc Mark search
I
119 WAD6
120 WAD7 Outside A/D data entry terminal for PSP Physical Disc Mark search (MSB)
C 122 TESTI It is fixation in "L" a test input terminal.

I
123 WCK Movement clock for PSP Physical Disc Mark search
124
WAVDD - A/D power supply terminal for PSP Physical Disc Mark search
125
126 WARFI Analog RF signal input terminal for PSP Physical Disc Mark search
Ai
127 WAVRB A/D bottom reference terminal for PSP Physical Disc Mark search
128
WAVSS - A/D ground terminal for PSP Physical Disc Mark search
129
131 DQ7 SDRAM data input-output terminal (MSB)
132 DQ6
I/O
D 133 DQ5 SDRAM data input-output terminal
134 DQ4
136 DQ3
137 DQ2 SDRAM data input-output terminal
I/O
138 DQ1
139 DQ0 SDRAM data input-output terminal (LSB)
141 DCLK Clock output terminal for SDRAM
142 DCKE Clock enable output terminal for SDRAM
143 XWE O Wright enable output terminal for SDRAM
E
144 XCAS Column address strobe output terminal for SDRAM
145 XRAS Row address strobe output terminal for SDRAM
147 TESTO Output terminal for test
148 A11 O Address output terminal for SDRAM (MSB)
149 A10 Address output terminal for SDRAM
120 DV-757Ai
1 2 3 4
5 6 7 8

151 A9 A
O Address output terminal for SDRAM
152 A8
154 A7
155 A6
O Address output terminal for SDRAM
156 A5
157 A4
159 A3
160 A2 Address output terminal for SDRAM
O
161 A1
162 A0 Address output terminal for SDRAM (LSB) B
164 XSRQ O Data request output terminal to input into a front end processor
165 XSHD Input terminal of a header flag output by a front end processor
166 SDCK Input terminal of a data carrier clock output by a front end processor
167 XSAK Input terminal of data partial response flag output by a front end processor
168 SDEF Input terminal of error flag output by a front end processor
169 SD0 The stream data input terminal which is output by a front end processor (LSB)
170 SD1
I
171 SD2
172 SD3
The stream data input terminal which is output by a front end processor C
173 SD4
174 SD5
175 SD6
176 SD7 The stream data input terminal which is output by a front end processor (MSB)
Ipu : Pull-up input, Ipd : Pull-down input, Ai : Analog input
DV-757Ai 121
5 6 7 8
1 2 3 4
7 PE5314B (FLKY ASSY : IC101)

FL Controller
A
Pin Function
No. Signal name Dir. Pin Functions
1 VDD1 Positive Power Supply (3.3 V)
2 VSS1 Ground Potential
3 X1 IN
Crystal Connection for Main System Clock Oscillation
4 X2
5 IC Internally Connected (Directly connect to VSS1)
6 RESET IN Reset Input
B 7 SCK1 IN Serial Clock Input of Serial Interface

8 SI1 IN Serial Data Input of Serial Interface
9 SO1 OUT Serial Data Output of Serial Interface
10 XRDY OUT Hand-shake (Ready) Output of Serial Interface
11 POWER ON OUT Power Control Output
12 RESET OUT OUT System Reset Output
13 RESERVE OUT OUT Reserved (NC on this model)
14 LED8 OUT LED Port 8 (NC on this model)
15 HALT IN Halt Port "NC" : Use Halt Mode
16 ACK IN Hand-shake (Acknowledge) Input of Serial Interface (Interrupt)
C
17 SEL IR IN Remote Control Input (Timer input of 8-bit remote control timer)
18 AVSS Ground Potential for A/D Converter
19 MS1 IN Destination (of player) Select (Analog Input for A/D Converter)
20 NC NC
21 KEY1 IN Key Input 1 (Analog input for A/D converter)
22 KEY0 IN Key Input 0 (Analog input for A/D converter)
23 VSS0 Ground Potential to Ports
24 AVDD Analog Power/Reference Voltage Input to A/D Converter (3.3 V)
25 VDD0 Positive Power Supply to Ports (3.3 V)
D
26 MS0_2
27 MS0_1 IN Model (of player) Select (Set with a combinaition of this 3 ports)
28 MS0_0
29 LED7 OUT LED Port 7
30 LED(STAND BY) OUT Stand By LED Port
Primary Switch State Input
31 PWSW IN
"H" : ON "L" : OFF
32 TES IN "H" : No System Reset mode "L" : General mode
33 OEM IN "H" : OEM Model "L" : Pioneer Model
E 34 MIC IN IN Detection of Microphone "H" : Microphone connected

35 CHECKER IN "H" : Checker Mode "L" : General mode
36 ON POWER IN "H" : Primary Power Switch Model "L" : Secondary Power Switch Model
FL-Controller Mode Select
37 FL SET2 FL SET1 / 2 = "H" / "H" : Other model
IN FL SET1 / 2 = "H" / "L" : Other model
38 FL SET1 FL SET1 / 2 = "L" / "H" : Other model
FL SET1 / 2 = "L" / "L" : DV-555, 656A, 757Ai (This model)
39 TEST2 OUT Test Port
40 LED6 OUT LED Port 6
122 DV-757Ai
1 2 3 4
5 6 7 8
No. Signal name Dir. Pin Function

41 LED5 LED Port 5 A
42 LED4 LED Port 4
43 LED3 LED Port 3 (NC on this model)
OUT
47 TEST1 OUT Test Port
48 NC NC
49 1394RST OUT 1394 Host Controller Reset Output
50 NC NC B
51 P16 OUT FIP Segment 16 Output
53 NC NC
54 P14 FIP Segment 14 Output
59 VDD2 Positive Power Supply to FIP Controller/Driver (3.3 V)
C
60 VLOAD Pull-down Resistor Connection of FIP Controller/Driver (-28V)
D
70 G11 FIP Grid 11 Output
75 G6 OUT FIP Grid 6 Output
78 G3 FIP Grid 3 Output E

DV-757Ai 123
5 6 7 8
1 2 3 4
7 PE5286A (DVDM ASSY : IC701)

DVD Data Processor
A
Pin Function
3 , 4 0 , 5 0 , 5 4 , VDD3.3 It is a power supply of digital circuit. Be connected to +3.3V.
84, 103, 107,
145, 154, 158,
207
15, 18, 27, 53, VDD2.5 It is a power supply of digital circuit. Be connected to +2.5V.
64, 74, 78, 92,
104, 130, 157,
164, 183, 191,
208
B 1 , 2 , 1 6 , 1 7 , GND It is a ground of digital circuit.
26, 41, 51, 52,
63, 73, 79, 85,
91, 105, 106,
131, 144, 150,
155, 156, 178,
182, 190
167, 171, 175 NC It is a non-use pin. Fix it in GND or VDD.
165 It is a power supply supply terminal for built-in analog-to-digital converter.

AVDD
166 Supply +2.5V (analog).
176
AGND It is a GND terminal for built-in D/A converter.
C 177
It is a separation test control terminal of inside RAM.
6 BUNRI IN
Input LOW in use usually.
90 TMC1 IN
It is a test terminal. Input LOW in use usually.
148 TMC2 IN
4 DMCK/RF_A IN It is the system clock input of DVD/CD-ROM decoder. Input 10-54MHz.
It is master clock of an audio system I/F block.
189 CKCD IN
In audio out of a CD, input 16.9MHz of reference clock.
5 DMACKI/PD4 IN Fix unused time (unused usually) in GND or VDD.
149 VCOCLK IN With system clock of spindle demodulator, it is connected to VCO of outside charge account.
D 161 XRESET IN By the input of a LOW level, It initialize the whole large scale integrated circuit system.
135 SA19 I/O Connect address bus of central processing unit.
134 SA18
133 SA17
132 SA16
129 SA15
128 SA14
127 SA13
126 SA12
125 SA11
E
124 SA10
123 SA9
124 DV-757Ai
1 2 3 4
5 6 7 8

122 SA8 IN Connect address bus of central processing unit. A
121 SA7
120 SA6
119 SA5
118 SA4
117 SA3
116 SA2
115 SA1
114 SA0
99 SAD7 I/O Connect a data bus of central processing unit. B
100 SAD6
101 SAD5
102 SAD4
108 SAD3
109 SAD2
110 SAD1
111 SAD0
97 XSRD IN Be connected to a RD signal of central processing unit.
98 XSWR IN Be connected to a WR signal of central processing unit.
C
It is chip select signal from central processing unit.
96 XSCL1 IN
XSRD/XSWR becomes effective at the time of LOW this signal.
It is the WAIT output for central processing unit.
95 XSWAIT OUT
This terminal must leave access from central processing unit at the time of LOW.
It is a DMA demand for central processing unit.
94 XSDREQ OUT
LOW level hip of this terminal falls down and activates DMA transfer with an edge.
It is DMA answer back.
93 SDACK IN
Data are output with HIGH this signal by SAD (7:0).
112 XIRQ10 It demand interrupt for central processing unit with LOW.
OUT
113 XIRQ11 Both terminals can set it with a register whether they output it.
141 FGPL/PE3 IN Input a turn pulse from spindle motor.

D
It is 7bitPWM output terminal for FG servo.
147 FPWM OUT
It is the 3 value output of HIGH,LOW, high impedance.
It is 5bitPWM output terminal for speed servo.
146 VPWM OUT
It is pulse width modulation output terminal for phase servo.
143 PPWM OUT
It is control output for rough servo.
142 RERR OUT
31 PA7 I/O It is general-purpose I/O port. By setting of a $70 register, You can select a function.
CDDO inputs a digital out signal from a CD decoder.
32 PA6 DIFOUT is digital audio output terminal based on IEC958.
33 PA5 BCA is terminal to input a BCA code into.
RWDIN is terminal to input a WOBBLE signal into. E
34 PA4
BCA/RWDIN terminal becomes necessary with RW revitalization machines.
35 CDDO/PA3
36 DIFOUT
196 BCA/PA1
195 RWDIN/PA0
DV-757Ai 125
5 6 7 8
1 2 3 4

A 138 PD7/STATUS2 OUT It output a various monitor signal (STATUS (2:0)).
By setting of a $ 70 register, You can use it as a general-purpose I/O port port.
139 PD6/STATUS1
140 PD5/STATUS0
It always output a pulse of duty 50%.
151 DUTY50 OUT
It give reference voltage of a various PWD signal of the recovery system.
160 ASC OUT It output frequency error of a sink period as a PWD pulse.
153 APC OUT It output a phase error of phase locked loop as a PWD pulse.
159 ATC OUT It output a direct current error of a RF signal as a PWD pulse.
It output VC OCL k and frequency error of reference clock as a PWD pulse.
152 AFC OUT
B It is the diffect signal input from the outside.
163 DEFECT/PE1 IN Then a phase error of phase locked loop outputs this terminal in HIGH (APC), and it is done
front value hold.
162 T_DET/PC7 OUT It output a tangential-tilt search result as a pulse width modulation pulse.
70 DA13 OUT It is address signal of DRAM for a VBR buffer.
71 DA12
72 DA11
75 DA10
76 DA9
77 DA8
C 80 DA7
81 DA6
82 DA5
83 DA4
86 DA3
87 DA2
88 DA1
89 DA0
39 DD15 I/O It is a data bus of DRAM for a VBR buffer.
42 DD14
D
43 DD13
44 DD12
45 DD11
46 DD10
47 DD9
48 DD8
49 DD7
55 DD6
56 DD5
E
57 DD4
58 DD3
59 DD2
60 DD1
61 DD0
126 DV-757Ai
1 2 3 4
5 6 7 8

69 XDRAS OUT It is a RAS signal of DRAM of a VBR buffer. A
67 XDCAS/XDCASL OUT It is a CAS signal of DRAM of a VBR buffer.
66 XDOE/DQML OUT It is an OE signal of DRAM of a VBR buffer.
65 XDWE OUT It is a WE signal of DRAM of a VBR buffer.
13 SDATA7 OUT It is a data output bus of a VIDEO_DMA channel.
Be connected to MPEG decoder.
14 SDATA6
19 SDATA5
20 SDATA4
21 SDATA3
22 SDATA2 B
23 SDATA1
24 SDATA0
It is a data transfer demand terminal of a VIDEO_DMA channel.
29 SREQ IN Be connected to MPEG decoder.
You can change polarity by setting.
It is a transfer reply terminal of a VIDEO_DMA channel.
25 XSACK/PC5 OUT Be connected to MPEG decoder.
Output form varies with setting.
It is a transfer reply terminal of a VIDEO_DMA channel.
28 XWR OUT Be connected to MPEG decoder.
30 XAVTRM/PC6 OUT It is a signal to show the top of a sector of transfer data of a VIDEO_DMA channel in. C
7 DSPA0/PC0 OUT When it connects Motorola Digital Signal Processor as destination of an AUDIO_DMA
channel, it is the signal which gives a DMA address to Motorola Digital Signal Processor.
8 DSPA1/PC1
9 DSPA2/PC2
206 ASDATA0/PB0 I/O It is general-purpose I/O port.
By setting of a $70 register, It become a data output bus of an AUDIO_DMA channel
205 ASDATA1/PB1 besides a port.
204 ASDATA2/PB2
203 ASDATA3/PB3
202 ASDATA4/PB4
201 ASDATA5/PB5 D
200 ASDATA6/PB6
199 ASDATA7/PB7
It is a transfer reply terminal of an AUDIO_DMA channel.
10 XAWR OUT
It is a transfer reply terminal of an AUDIO_DMA channel.
11 XASACK OUT
It is a transfer demand terminal of an AUDIO_DMA channel.
12 ASREQ IN
You can change polarity by setting.
192 BCK OUT It is the bit clock output to DAC.
193 LRCK OUT It is the LRCK signal output to DAC.
E
194 ADATA0 OUT It is the serial data output to DAC.
It input a bit clock from a CD decoder.
187 CDBCK IN
Prospective frequency is 2.1168MHz(48fs).
186 CDLR IN It input a LRCK signal from a CD decoder.
185 CDDT IN It input audio system data from a CD decoder.
181 WFCK IN It is frame clock signal of a CD.
180 SCOR IN It is input terminal of assistant code sink of a CD.
DV-757Ai 127
5 6 7 8
1 2 3 4

A 179 SBSO IN It is an assistant code data input terminal of a CD.
184 EXCK OUT It is a shift clock making timeliness to send data forth on a SBSO terminal.
188 C2FI/PE2 IN It is input terminal of C2 error flag from a CD decoder.
It input a FSX signal from a CD decoder.
FSX signal is 7.35Khz at normal speed with frame alignment signal of error correction of
136 FSX/STATUS4 I/O
CIRC.
By setting of a $7F register, It become the internal monitor output (STATUS 4).
It input an EFLG signal from a CD decoder.
137 EFLG/STATUS3 I/O An EFLG signal is a monitor signal of error correction processing movement of CIRC.
By setting of a $7F register, It become the internal monitor output (STATUS 3).
172 AIN IN It is analog RF signal input terminal to built-in A/D converter.
B 168 VRT IN It is reference voltage input terminal of built-in A/D converter.

169 VRTS OUT Connect with VRT.
170 VRC OUT It is center voltage output terminal of built-in A/D converter.
174 VRB IN It is reference voltage input terminal of built-in A/D converter.
173 VRBS OUT Connect with VRB.
37 CKE/PD3 OUT It is an Enable signal of SDCLK.
38 CSB/PD2 OUT It is chip select signal of SDRAM.
62 SDCLK OUT It is a terminal outputting a movement clock of SDRAM.
68 XCASH/DOMH OUT When it uses DRAM of bus 16 wide bit, it is a CAS signal of high rank 8bit.
197 VREQEN/PD1 I/O It is an Enable signal of Video-REQ.
C
198 AREQEN/PD0 I/O It is an Enable signal of Audio-REQ.
128 DV-757Ai
1 2 3 4
5 6 7 8
7 PD0274A (DVDM ASSY : IC552)

Audio Quality Enhancer (AQE)
A
Pin Arrangement Block Diagram
1 DAIN DALOUT 24 IBS, TFS, IFS, LRIPOL, 24
2 LRIN DAROUT 23 IFORM, CKSEL, TEST
LRCK Bit Extension IBS, BES, DIR
3 BCKIN LROUT 22
4 RSTB BCKOUT 21 DAIN 1 24
Input 24 LRCK
5 CGND LRIN 2 Inter face
CGND 20 x8
BCKIN 3 LRCK Digital Filter
6 XIN OVDD 19
ATT +
7 IGND NC 18 BACS, BSO, OFORM, Deemphasis
8 ICVDD NC 17 LRPOL, DACS, TEST
9 SCLK NC 16
DALOUT 24
10 SDATA NC 15 24 x2 B
DAROUT 23 1st FIR Filter IFS, DFS, CKSE,
11 CSB NC 14 Output COES, ATT, DE
Inter face
LROUT 22
12 NC NC 13 2fs
BCKOUT 21 n*
LRCK
x2
CKSE 2st FIR Filter
RSTB 4 4fs
Timing
Control Syscllk
x2
XIN 6 3st FIR Filter
24 8fs n*
LRCK
24
SDATA 10 IFS, SMUTE,
Soft Mute
SCLK 9
Microcomputer TEST C
Interface n*
CSB 11 LRCK
Note :
"n" in the Block diagram expresses the rate to sample
Pin Function
No. Name I/O Pin Function
1 DAIN I Audio data input
2 LRIN I L/R clock input
3 BCKIN I Bit clock input (48fs/64fs)
4 RSTB I System reset "0" = Reset
5 CGND Ground (0V) for Core D
6 XIN I System clock input (128fs/192fs/256fs/384fs/512fs/768fs)
7 IGND Ground (0V) for Input Buffer
8 ICVDD Power supply (3.3V) for Core and Input Buffer
9 SCLK I Microcomputer interface clock input
10 SDATA I Microcomputer interface data input
11 CSB I Microcomputer interface chip select input "0" = Enable, "1" = Disenable
12 NC
13 NC
14 NC
I No connection
15 NC E
16 NC
17 NC
18 OVDD Power supply (3.3V) for Output Buffer
19 OGND Ground (0V) for Output Buffer
20 CGND Ground (0V) for Core
21 BCKOUT O Bit clock output (48fs/64fs)
22 LROUT O L/R clock output. WCLK output at PCM1704.
23 DAROUT O R ch audio data output
24 DALOUT O L ch audio data output or L/R ch multiplex output
F
DV-757Ai 129
5 6 7 8
1 2 3 4
7 ADV7300AKST (DVDM ASSY : IC831)

Video Encoder IC
A
Pin Arrangement
130 DV-757Ai
1 2 3 4
5 6 7 8
Pin Function
DV-757Ai 131
5 6 7 8
1 2 3 4
132 DV-757Ai
1 2 3 4
5 6 7 8
7 PM0033A (DVDM ASSY : IC902)

Progressive Scan Converter (PRO2)
A
Pin Arrangement
DV-757Ai 133
5 6 7 8
1 2 3 4
Pin Function
Pin Name I/O/ Attribute Functional Description
A No. P
1 VDD3 P - VDD for IO (3.3V)
2 CLKI In LVTTL 27MHz System clock input terminal
3 PLL_TEST In LVTTL Test exclusive use input terminal
4 PLL_EN In LVTTL PLL enable input terminal
5 VDD2 P - VDD for Core (2.5V)

6 CLKO Out 2mA 27MHz Clock output terminal
B 7 PD0 Inout LVTTL, leakage, 2mA Image data I/O port D(LSB)
8 PD1 Inout LVTTL, leakage, 2mA Image data I/O port D
12 GND P - Digital Ground
C
18 PD9 Inout LVTTL, leakage, 2mA Image data I/O port D(MSB)
23 NHS In Schmitt Horizontal synchronization input terminal
D 24 NVS In Schmitt Vertical synchronization input terminal
25 PA0 In LVTTL Image data I/O port A(LSB)
26 PA1 In LVTTL Image data I/O port A
E
34 PA9 In LVTTL Image data I/O port A(MSB)
35 MA4 Out 2mA SDRAM address output terminal
F
134 DV-757Ai
1 2 3 4
5 6 7 8

No. P
41 VDD2 P - VDD for Core (2.5V) A
45 MA0 Out 2mA SDRAM address output terminal(LSB)
50 MA11 Out 2mA SDRAM address output terminal(MSB) B
52 RAS Out 2mA SDRAM Row Address Strobe Command output terminal
53 MCLK Out 4mA SDRAM Clock output terminal (54MHz)
54 CAS Out 2mA SDRAM Column Address Strobe
Command output terminal
55 WE Out 2mA SDRAM Write Enable output terminal
57 MD8 Inout LVTTL, 2mA, Pullup SDRAM data input-output terminal
58 MD7 Inout LVTTL, 2mA, Pullup SDRAM data input-output terminal C
60 PDOEN In LVTTL Image port D input and output setting input terminal
(L: input, H: output )
66 MD5 Inout LVTTL, 2mA, Pullup SDRAM data input-output terminal D
75 MD14 Inout LVTTL, 2mA, Pullup SDRAM data input-output terminal E
78 MD0 Inout LVTTL, 2mA, Pullup SDRAM data input-output terminal(LSB)
F
DV-757Ai 135
5 6 7 8
1 2 3 4

No. P
A
86 MD19 Inout LVTTL, 2mA, Pullup SDRAM data input-output terminal(MSB)
88 AGND P - Ground for DAC
89 DAO_Y Out - Analog video-out (Y)
90 AVDD2 P - VDD for DAC (2.5V)
91 DAO_Cb Out - Analog video-out (Cb)
93 DAO_Cr Out - Analog video-out (Cr)
B
95 VREF In - DAC reference voltage input terminal
96 FSADJ Inout - An ohms connection terminal for DAC peak swing setting
98 VG Out - A volume connection terminal for gate voltage
compensation of a DAC electric current cell
C
104 CLMP Out 2mA Clamp pulse output terminal
105 TEST0 In LVTTL Test exclusive use input terminal
110 SPR0 Out 2mA Serial-to-parallel conversion output terminal(LSB)
D 111 SPR1 Out 2mA Serial-to-parallel conversion output terminal
113 SPR2 Out 2mA Serial-to-parallel conversion output terminal
119 SPR7 Out 2mA Serial-to-parallel conversion output terminal(MSB)
E 120 VDD3 P - VDD for IO (3.3V)
123 PB0 Inout LVTTL, leakage, 2mA Image data I/O port B(LSB)
124 PB1 Inout LVTTL, leakage, 2mA Image data I/O port B
F
136 DV-757Ai
1 2 3 4
5 6 7 8

No. P
129 PB5 Inout LVTTL, leakage, 2mA Image data I/O port B A
134 PB9 Inout LVTTL, leakage, 2mA Image data I/O port B(MSB)
135 PBOEN In LVTTL Image port B input and output setting input terminal
(L: input, H: output )
137 PC0 Out 2mA Image data I/O port C(LSB) B
138 PC1 Out 2mA Image data I/O port C

145 VDD3 P - VDD for IO (3.3V) C
149 PC9 Out 2mA Image data I/O port C(MSB)
151 CSB In Schmitt MPU Interface chip select input terminal
152 SDA In Schmitt MPU Interface data entry terminal
153 SCL In Schmitt MPU Interface clock input terminal
D
154 SRN In Schmitt System reset input terminal
155 CKIPOL In LVTTL System clock polarity setting input terminal
156 PLL_VDD P - VDD of PLL exclusive use (2.5V)
157 CPOUT Out Analog Analog output terminal from PLL charge pump
158 VCOIN In Analog Analog input terminal from PLL outside charge
account loop filter
159 PLL_GND P - Ground of PLL exclusive use
DV-757Ai 137
5 6 7 8
1 2 3 4
7 TSB43CA43GGW (ILKB ASSY : IC201)

IEEE1394 PHY LINK
A
Pin Arrangement
176
175
174
173
172
171
170
169
168
167
166
165
164
163
162
161
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
3.3v
HSDI1_60958_OUT
HSDI1_AMCLK_OUT
MCIF_MODE2
MCIF_MODE1
MCIF_MODE0
Vdd
Vdd
Vdd
REG_OUT
Vss
Vss
Vss
HSDI1_EN
HSDI0_EN
HSDI1_AV
HSDI0_AV
HSDI1_AUDIO_MUTE
HSDI1_AUDIO_ERR
HSDI1_SYNC
HSDI0_SYNC
HSDI1_60958_IN
HSDI0_60958_IN
HSDI1_AMCLK_IN
HSDI0_AMCLK_IN
HSDI1_D7
HSDI1_D6
HSDI1_D5
HSDI1_D4
HSDI1_D3
HSDI1_D2
HSDI1_D1
HSDI1_D0
HSDI0_D7
HSDI0_D6
HSDI0_D5
HSDI0_D4
HSDI0_D3
HSDI0_D2
HSDI0_D1
HSDI0_D0
HSDI1_CLK
HSDI0_CLK
HSDI1_DVALID
HSDI0_DVALID
1 132
B 2 Vss MCIF_ENDIAN 131
3 TEST_MODE0 Vss 130
4 TEST_MODE1 Vdd 129
5 Vdd MCIF_ADDR10 128
6 VCO_CLK MCIF_ADDR9 127
7 REF_SYT MCIF_ADDR8 126
8 DIV_VCO MCIF_ADDR7 125
9 PFD MCIF_ADDR6 124
10 MLPCM_BCLK MCIF_ADDR5 123
11 MLPCM_LRCLK MCIF_ADDR4 122
12 MLPCM_D0 MCIF_ADDR3 121
15 MLPCM_A MCIF_DATA15 118
16
17
18
GPIO2
GPIO3
GPIO4
GPIO5
TSB43CA43 MCIF_DATA14
Vss
Vdd
REG_OUT
117
116
115
C 19 114
20
21
22
MSPCTL
Vdd
Vss
(iceLynx-Micro) MCIF_DATA13
MCIF_DATA12
MCIF_DATA11
113
112
111
23 CPS MCIF_DATA10 110
24 AVdd MCIF_DATA9 109
25 AGND MCIF_DATA8 108
26 TPB0_N MCIF_DATA7 107
27
28
29
TPB0_P
AGND
AVdd
INTEGRATED MCIF_DATA6
MCIF_DATA5
MCIF_DATA4
106
105
104
30
31
32
TPA0_N
TPA0_P
TPBIAS0
AVdd
LLC / PHY MCIF_DATA3
MCIF_DATA2
Vss
Vdd
103
102
101
33 100
34
35
36
TPB1_N
TPB1_P
AGND
Plastic QFP MCIF_DATA1
MCIF_DATA0
MCIF_BUSCLK
99
98
97
D TPA1_N MCIF_WEz
37 96
38 TPA1_P MCIF_OEz 95
39 TPBIAS1 MCIF_ACKz 94
40 TPB2_N MCIF_WAIT 93
41 TPB2_P MCIF_STRBz 92
42 AVdd MCIF_R_nW 91
43 TPA2_N MCIF_CS_MEMz 90
44 TPA2_P MCIF_CS_IOz 89
TPBIAS2 MCIF_INTz
LOW_PWR_RDY
WTCHDOG_TMR
RESET_ARMz
TEST_MODE2
TEST_MODE3
DISABLE_IFz
UART_TxD
UART_RxD
ARM_TDO
ARM_TMS
REG_OUT
PLL_GND
REG_ENz
ARM_TDI
LINK_ON
PLL_Vdd
RESETz
FILTER0
FILTER1
GPIO10
GPIO0
GPIO1
GPIO6
GPIO7
GPIO8
GPIO9
AGND
TRST
AVdd
TMS
SCL
TCK
SDA
TDO
HPS
Vss
Vss
Vdd
Vdd
XO
R1
R0
TDI
XI
E
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
138 DV-757Ai
1 2 3 4
5 6 7 8
Pin Function
Pin Name Pin No I/O Description
A
Power & Ground Pins

DISABLE_IFZ 64 I Interface Disable. When asserted, the interfaces are put into
a Hi-Z state. Interfaces include: ex-CPU, HSDI, GPIO, and
WTCH_DG_TMRZ.
HPS 62 I Host Power Status. This indicates the power status of the
external system to iceLynx-Micro. A rising edge indicates the
system CPU has been turned ON. (The internal ARM should
wake up.) A falling edge indicates the system CPU has been
turned OFF. (The internal ARM decides if power down is
necessary.) B
LOW_PWR_RDY 63 O Output to system to indicate iceLynx-Micro is ready to go into
a low power state. The ARM and WTCH_DG_TMRZ control
this pin.
WTCH_DG_TMRZ 88 O Watch Dog Timer (for the ARM.) iceLynx-Micro hardware
asserts this pin whenever ARM software has not updated the
Timer2 register within the allowed time period.
RESET_ARMZ 60 I ARM reset. This signal resets the internal ARM processor.
RESETZ 59 I/O Device reset. This signal resets all logic. This includes the
PHY, Link core, memory, the ARM, and random logic.
VSS 1, Digital Ground.
21, C
55,
76,
102
117
131,
146,
162
176
AGND 24, Analog Ground.
27,
35, D
45,
PLL_GND 54 PLL Ground.
VDD 4, Digital Power Supply. Must be set to 3.3V nominal.
20,
56,
75,
101
116,
130
145,
161 E
175
DV-757Ai 139
5 6 7 8
1 2 3 4

A
AVDD 23, Analog Power Supply. Must be set to 3.3V nominal.

28,
32,
41,
48
PLL_VDD 51 PLL Power Supply. Must be set to 3.3V nominal.
Regulator Pins
REG_ENZ 73 I Internal Regulator Enable. The iceLynx-Micro core voltage is
1.8V. Internal regulators are used to regulate the 3.3V VDD
B inputs to 1.8V. This pin enables the regulators.
REG_OUT0 74 O 1.8V Regulator Output. This pin should be connected to
ground using a 0.1uF capacitor.
External CPU Interface Pins
MCIF_ACKZ 95 I/O MCIF Acknowledge pin. Default active low. iceLynx-Micro
asserts this signal if it has completed the MCIF request. This
signal is always driven. This signal is used for the following
C modes:
68000 + Wait I/O Access
MPC850 I/O Access
In Serial MCIF Mode, this pin is used for the Serial Read
Acknowledge (SMCIF_RACKZ.)
MCIF_ADDR1 120 I MCIF Address 1 pin. This data pin is the least significant bit of
the MCIF Address Bus.
MCIF_ADDR0 is internally grounded. Only 16-bit addressing
D is allowed. MCIF_ADDR1 should be connected to the
Address1 signal of the system CPU.
MCIF_ADDR10 129 I MCIF Address 10 pin. This data pin is the most significant bit
of the MCIF Address Bus.
MCIF_ADDR2 121 I MCIF Address 2 pin
E MCIF_ADDR9 128 I MCIF Address 9 pin
140 DV-757Ai
1 2 3 4
5 6 7 8

A
MCIF_BUSCLK 98 I MCIF Bus Clock. This pin is only used for the MCIF
synchronous mode. (MPC850 I/O Access) and the Memory
Access.
This signal should be tied high if not used.
In Serial MCIF Mode, this pin is used for the Serial Write Clock
(SMCIF_WCLK.)
MCIF_CS_IOZ 90 I MCIF Chip Select for all I/O MCIF modes.
In Serial MCIF Mode, this pin is used for the Serial Write B
Request (SMCIF_WREQZ.)
MCIF_CS_MEMZ 91 I/O MCIF Chip Select for the Memory MCIF mode.
In Serial MCIF Mode, this pin is used for the Serial Write
Acknowledge (SMCIF_WACKZ.)
MCIF_DATA0 99 I/O MCIF DATA 0 pin. This data pin is the least significant bit of
the MCIF Data Bus.
In Serial MCIF Mode, this pin is used for the Serial Read Data
(SMCIF_RDATA.)
MCIF_DATA1 100 I/O MCIF DATA 1 pin. C
MCIF_DATA10 111 I/O MCIF DATA 10 pin.

MCIF_DATA15 119 I/O MCIF DATA 15 pin. This data pin is the most significant bit of
the MCIF Data Bus.
MCIF_DATA2 103 I/O MCIF DATA 2 pin. D
MCIF_ENDIAN 132 I MCIF Endian Pin. This sets the Endianess for accesses
between the external CPU and the internal iceLynx-Micro
memory. This pin sets Endianess for all MCIF modes and the
Serial MCIF mode. E
When set to a logical 0, data is read/written to the ex-CPU
exactly as it is stored in iceLynx-Micro memory. (Big Endian)
When set to a logical 1, data is swapped on half-word and
byte boundaries before it is read/written to the ex-CPU. (Little
Endian)
DV-757Ai 141
5 6 7 8
1 2 3 4

A
MCIF_INTZ 89 O MCIF Interrupt. This signal is push-pull. (always asserted) It

does not require a pull-up resistor.
MCIF_MODE0 133 I MCIF Mode 0. Used to select MCIF mode.
MCIF_OEZ 96 I MCIF Output Enable. Default active low. This input pin
indicates if the system CPU wants to perform a MCIF read
access. This signal is used for the following modes:
SH-3 I/O Access
B
M16C/62 I/O Access
Memory Access
This signal should be tied high if not used.
MCIF_RW 92 I MCIF Read/Write pin. Default value for read is a logical 1.
Default value for write is a logical 0.
In Serial MCIF Mode, this pin is used for the Serial Write Data
(SMCIF_WDATA.)
MCIF_STRBZ 93 I MCIF Strobe pin. Default active low. This pin is used (along
with MCIF_CS_IOZ) to validate the MCIF access. This signal
is used for the following modes:
C 68000 + Wait I/O Access
MPC850 I/O Access
When not used, this pin should be tied high.
Clock (SMCIF_RCLK.)
MCIF_WAIT 94 O MCIF Wait pin. Default active high. iceLynx-Micro asserts
this signal if it is not ready to service an MCIF request. When
not asserted, this signal is in high-Z state. This signal is used
for the following modes:
68000 + Wait I/O Access
D SH-3 I/O Access
M16C/62 I/O Access
Request (SMCIF_RREQZ.)
MCIF_WEZ 97 I MCIF Write Enable. Default active low. This input pin
indicates if the system CPU wants to perform a MCIF write
access. This signal is used for the following modes:
SH-3 I/O Access
M16C/62 I/O Access
Memory Access
E This signal should be tied high if not used.
Universal Asynchronous Receiver Transmitter Pins
UART_RxD 86 I UART receive port. Data from the system is input to the
UART buffer using this pin.
UART_TxD 85 O UART transmit port. Data from the UART buffer is output to
the system using this pin.
142 DV-757Ai
1 2 3 4
5 6 7 8

A
Joint Test Action Group (JTAG) & ARM Pins

JTAG_TCK 80 I JTAG Clock pin. Both the boundary scan and ARM JTAG
uses this input for the JTAG clock.
JTAG_TDI 78 I JTAG Test Data Input pin
JTAG_TDO 79 O JTAG Test Data Output pin
JTAG_TMS 77 I JTAG Test Mode Selector pin.
JTAG_TRST 81 I JTAG Reset Pin. Both the boundary scan and ARM JTAG
uses this input for the JTAG clock.
ARM_JTAG_TDI 83 I ARM JTAG Test Data Input pin
B
ARM_JTAG_TDO 84 O ARM JTAG Test Data Output pin
ARM_JTAG_TMS 82 I ARM JTAG Test Mode Selector pin

2
I C Serial Bus Pins
2
SCL 68 I/O I C Clock Pin. This pin should be tied to ground if no EEPOM
is used.
For EEPROM write operations, the GPIO8 settings are muxed
with the SCL pin. Software can manipulate the GPIO8
register settings in order to perform a write.
2
SDA 67 I/O I C Data Pin
For EEPROM write operations, the GPIO9 settings are muxed
with the SDA pin. Software can manipulate the GPIO9 C
register settings in order to perform a write.
General Purpose Input/Out Pins (GPIO)
GPIO0 65 I/O GPIO0. Can be programmed as general-purpose input,
general-purpose output, or specific function. Power-up default
is input.
is input.
is input. D
is input.
GPIO4 17 I/O GPIO 4. Can be programmed as general-purpose input,
is input.
GPIO5 18 I/O GPIO 5. Can be programmed as general-purpose input,
is input.
general-purpose output, or specific function. Power-up default E
is input.
is input.
DV-757Ai 143
5 6 7 8
1 2 3 4
Pin Name I/O Description

A

is input.
is input.
is input.
B Physical Layer Pins
TPA0_N 29 I/O Twisted Pair A Differential Signal Terminals. For an unused
TPA1_N 36 port, TPAN and TPAP signals can be left open.
TPA2_N 42
TPA0_P 30
TPA1_P 37
TPA2_P 43
TPB0_N 25
TPB1_N 33 I/O Twisted Pair B Differential Signal Terminals. For an unused
TPB2_N 39 port, TPBN and TPBP signals can be left open.
TPB0_P 26
C TPB1_P 34
TPB2_P 40
TPBIAS0 31 Twisted Pair Bias Output. These signals provide the 1.86V
TPBIAS1 38 I/O nominal bias voltage needed for proper operation of the
TPBIAS2 44 twisted pair driver and receivers for signaling an active
connection to a remote node.
For an unused port, TPBIAS can be left unconnected.
R1 46 Current Setting Resistors. These pins are connected to
R0 47 external resistors to set the internal operating currents and
- cable driver output currents. A resistance of 6.34k 1% is
required to meet the IEEE 1394-1995 output voltage limits.
D FILTER0 49 PLL Filter Terminals. These terminals are connected to an
FILTER1 50 I/O external capacitor to form a lag-lead filter required for stable
operation of the internal frequency-multiplier PLL, which is
using the crystal oscillator. A 0.1 F 10% capacitor is the
only external component required to complete this filter.
XI 52 Crystal Oscillator Inputs. These terminals connect to a 24.576
X0 53 - MHz parallel resonant fundamental mode crystal. The
optimum values for the external shunt capacitors are
dependent on the crystal used.
CPS 21 I Cable Power Status. Input to iceLynx-Micro used to detect if
cable power is present. This pin should be connected to the
E cable power through 390 k resistor.
MSPCTL 19 I
LINKON 61 O Link On output. This signal is asserted whenever LPS is low
and a Link On packet is received from the 1394 bus.
High Speed Data Interface (HSDI) Port 0 Pins

HSDI_60958_IN 173 I 60958 Data Input.
144 DV-757Ai
1 2 3 4
5 6 7 8

A
HSDI_60958_OUT 179 O 60958 Data Output
This signal is also used as FLWCTRL_DVALID in Flow

Control Data Valid mode.
HSDI0_60958_IN 136 I 60958 Data Input.
HSDI0_AMCLK_IN 137 I Audio Master Clock Input. This clock is used to decode the bi-
phase encoding of 60958 data.
This pin is also used to input the 1.5*BCLK for Flow Control
mode. B
HSDI0_AV 140 O HSDI Port 0 Available. Programmable. Default active low.
For receive from 1394, this signal indicates if a 1394 packet is
available in the receive buffer for reading. The HSDI_AV
signal for MPEG2 data also depends on time stamp based
release.
For transmit onto 1394, this signal can be used to indicate
buffer level in HSDI TX mode 8 and 9 by programming a CFR.
If the buffer level is above a programmed level, HSDI_AV will
be asserted.
HSDI0_CLK 138 I HSDI Port 0 Clock. Programmable. Default rising edge
sample. This clock is used to operate the HSDI port 0 logic. C
In parallel mode, the maximum clock is 27MHz. In serial
mode, the maximum clock is 70MHz.
This signal is output to HSDI1_CLK in pass thru mode.
This signal can be used as HSDI0_MLPCM_BCLK for DVD-

Audio Transmit.
HSDI0_D0 143 I/O HSDI Port 0 Data 0 Pin. Data 0 is the least significant bit on
the HSDI data bus.
In serial mode, only HSDI0_D0 is used.
This signal is output to HSDI1_D0 in pass thru mode. D
This signal can be used as HSDI0_MLPCM_D0 for DVD-
Audio Transmit.
HSDI0_D1 144 I/O HSDI Port 0 Data 1 Pin

This signal is output to HSDI1_D1 in pass thru mode.
Audio Transmit.
Audio Transmit. E
This signal can be used as HSDI0_MLPCM_A for DVD-Audio
Transmit.
This signal is output to HSDI1_D4 in pass thru mode
DV-757Ai 145
5 6 7 8
1 2 3 4

A

HSDI0_D7 152 I/O HSDI Port 0 Data 7 Pin. Data 0 is the most significant bit on
the HSDI data bus.
HSDI0_DVALID 142 I/O HSDI Port 0 Data Valid Pin. Programmable. Default active
B
high. This pin indicates if data on the HSDI data bus valid for
reading or writing.
For transmit onto 1394, this signal is provided by the system
with the data.
For receive from 1394, iceLynx-Micro provides this signal with
the data.
For HSDI DV modes, this signal is used as
HSDI0_FrameSync indicating DV frame boundary.
This signal is output to HSDI1_DVALID in pass thru mode

If not used in transmit mode, this signal can be tied low.
C
HSDI0_EN 139 I HSDI Port 0 Enable. Programmable. Default active low. Input
by the system to enable the HSDI for both transmit and
receive from 1394.
If not used, this signal can be tied enabled (low or high
depending on the polarity set). The application can use
HSDI_DVALID or HSDI_SYNC to validate the HSDI data.
This signal can be used as HSDI0_MLPCM_LRCLK for DVD-
Audio Transmit.
HSDI0_SYNC 141 I/O HSDI Port 0 Sync Signal. Programmable. Default active high.
D This signal is used to indicate the start of packet.
with the data.
the data.
This signal is output to HSDI1_SYNC in pass thru mode.

If not used in transmit mode, this signal can be tied low or high
depending on the polarity.
High Speed Data Interface (HSDI) Port 1 Pins

E
146 DV-757Ai
1 2 3 4
5 6 7 8

A
HSDI1_AMCLK_IN 169 I Audio Master Clock Input. This clock is used to decode the bi-
phase encoding of 60958 data.
This pin is also used to input the 1.5*BCK for Flow Control
mode.
MLPCM Interface, HSDI1 Audio Port, and HSDI1 video port

share buffer 1. Only one interface can access the buffer at a
time.
HSDI1_AMCLK_OUT 170 O Audio Master Clock Output. This clock is derived from the B
VCO_CLK input. 60958 data output from iceLynx-Micro is bi-
phase encoded using this clock.
HSDI1_AUDIO_ERR 171 O Audio Error Signal. iceLynx-Micro asserts this signal
whenever an Audio Error condition occurs. (Receive from
1394 only.)
HSDI1_AUDIO_MUTE 172 O Audio Mute Status. iceLynx-Micro asserts this signal
whenever an Audio Mute condition has occurred, and
hardware has muted the HSDI1 audio interface. (Receive
from 1394 only.)
HSDI1_AV 155 O HSDI Port 1 Available. Programmable. Default active low.
C
For receive from 1394, this signal indicates if a 1394 packet is
available in the receive buffer for reading. The HSDI_AV
signal for MPEG2 data also depends on time stamp based
release.
For transmit onto 1394, this signal can be used to indicate
buffer level in HSDI TX mode 8 and 9 by programming a CFR.
This pin can be used to indicate buffer level in transmit mode

by programming a CFR. If the buffer level is above a
programmed level, HSDI_AV is asserted.
HSDI1_CLK 153 I/O HSDI Port 1 Clock. Programmable. Default rising edge D
sample. This clock is used to operate the HSDI port 1 logic.
In parallel mode, the maximum clock is 27MHz. In serial
mode, the maximum clock is 70MHz.
This signal can be used as HSDI1_SACD_MCLK for SACD

Transmit and Receive.

time.
HSDI1_D0 158 I/O HSDI Port 1 Data 0 Pin. Data 0 is the least significant bit on
E
the HSDI data bus. In serial mode, only HSDI0_D0 is used.
This signal can be used as HSDI1_SACD_D0 for SACD

DV-757Ai 147
5 6 7 8
1 2 3 4

A


B HSDI1_D3 164 I/O HSDI Port 1 Data 3 Pin



C Transmit and Receive.
This signal can be used as HSDI1_SACD_A for SACD

HSDI1_D7 168 I/O HSDI Port 1 Data 7 Pin. Data 0 is the most significant bit on
the HSDI data bus.
HSDI1_DVALID 157 I/O HSDI Port 1 Data Valid Pin. Programmable. Default active
high. This pin indicates if data on the HSDI data bus valid for
reading or writing.
D with the data.
the data.
For HSDI DV modes, this signal is used as
HSDI0_FrameSync indicating DV frame boundary.
If not used in transmit mode, this signal can be tied low.

HSDI1_EN 154 I HSDI Port 1 Enable. Programmable. Default active low.
Input by the system to enable the HSDI for both transmit and
receive from 1394.
If not used, this signal can be tied enabled (low or high
depending on the polarity set). The application can use
E
HSDI_DVALID or HSDI_SYNC to validate the HSDI data.
148 DV-757Ai
1 2 3 4
5 6 7 8

A
HSDI1_SYNC 156 I/O HSDI Port 1 Sync Signal. Programmable. Default active high.
This signal is used to indicate the start of packet
with the data.
the data.
If not used in transmit mode, this signal can be tied low or high
depending on the polarity.
B
This signal can be used as HSDI1_SACD_FRAME for SACD
DVD-Audio Interface Pins
MLPCM_A 14 I/O Audio MLPCM Interface Ancillary Data. Ancillary data is
input/output using this pin. For DVD-Audio, MLPCM_LRCLK
determines if Ancillary Left or Ancillary Right data is present.
This signal also functions as FLWCTL_A in Flow Control

mode
MLPCM_BCLK 9 I/O Audio MLPCM Interface Bit Clock. Multiple functions: C

DVD Audio BCK (I)
DVD Audio BCK (O)
Flow Control BCK (I/O)

time.
MLPCM_D0 11 I/O Audio MLPCM Interface D0. Contains Channel 1 and
Channel 2 information. MLPCM_LRCLK determines which
channel is present.
D
This signal also functions as FLWCTL_D0 in Flow Control
mode.
channel is present.

mode
channel is present.
E

mode
MLPCM_LRCLK 10 I/O Audio MLPCM Interface Left-Right Clock. Multiple functions:
DVD Audio LRCLK (I)
DVD Audio LRCLK (O)
Flow Control LRCLK (I/O)
DV-757Ai 149
5 6 7 8
1 2 3 4

A
Phase Lock Loops Pins

DIV_VCO 7 O Output for External Phase Detector. This signal is the divided
VCO_CLK. It used by the external phase detector to compare
with the REF_SYT signal. The divide ratios are setup in CFR.
PFD 8 O Output from Internal Phase Detector. This signal can feed
directly into the LPF and VCO if the internal phase detector is
used.
REF_SYT 6 O Output for External Phase Detector. This signal represents
the SYT match for received audio or DV packets. The phase
B detector uses it as input to detect differences between the
SYT match and the VCO clock.
VCO_CLK 5 I Input from VCO. This is used to generate internal audio and
DV clocks for receive clock recovery.
Audio Frequency: 33.868MHz or 36.864MHz.
DV Frequency: 30.72MHz
Test Mode Pins
TEST_MODE0 2 I/O Test Mode. Used for Internal TI testing. Should be tied low
for normal operation.
TEST_MODE1 3 I/O Test Mode. Used for Internal TI testing. Should be tied low
for normal operation.
C TEST_MODE2 57 I/O Test Mode. Used for Internal TI testing. Should be tied low
TEST_MODE3 58 for normal operation.
150 DV-757Ai
1 2 3 4
5 6 7 8
7 PD5787A (ILKB ASSY : IC101)

HOST CPU
A
Pin Arrangement
Block Diagram
D
I/O port port P0 port P1 port P2 port P3 port P4 port P5 port P6
port P7
Inside outskirts function System clock outbreak
Timer A-D converter
(10 bit 8 channel)
Timer TA0 (16 bit)
Timer TA1 (16 bit)
port P8
Timer TA2 (16 bit) UART / clock synchronizer form SI/O Clock synchronizer SI/O
Timer TA3 (16 bit) (8 bit 3 channel) (8 bit 2 channel)
Timer TB0 (16 bit)
Timer TB1 (16 bit)
CRC operationed circuit
Timer TB2 (16 bit)
(CCITT system)
port P85
Timer TB3 (16 bit) E
Timer TB4 (16 bit)
Timer TB5 (16 bit) 16-bit core based CPU Memory
Registers Program counter
Monitor timer
port P9
(15 bit) Stack pointer
DMAC
(2 channel)
Vector table
port P10
D-A converter
(8 bit 2 channel) Flag register Multiplier
DV-757Ai 151
5 6 7 8
1 2 3 4
7.3 DISC / CONTENT FORMAT PLAYBACK COMPATIBILITY
152 DV-757Ai
1 2 3 4
5 6 7 8
7.4 CLEANING
A
Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools:
Position to be cleaned Cleaning tools
Pickup lenses Cleaning liquid : GEM1004

Cleaning paper : GED-008
DV-757Ai 153
5 6 7 8
1 2 3 4
8. PANEL FACILITIES
A
154 DV-757Ai
1 2 3 4
5 6 7 8
[DV-757Ai/WYXJ]
A
DV-757Ai 155
5 6 7 8
1 2 3 4
[DV-S755Ai/RLXJ/NC]
A
156 DV-757Ai
1 2 3 4
5 6 7 8
DV-757Ai 157
5 6 7 8
1 2 3 4
158 DV-757Ai
1 2 3 4
5 6 7 8
DV-757Ai 159
5 6 7 8

DV 757ai

Uploaded by

Copyright:

Available Formats

DV 757ai

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DV 757ai

Uploaded by

Copyright:

Available Formats

ORDER NO.

DV-757Ai WYXJ AC220-240V 2

For details, refer to "Important symbols for good services".

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

LASER DIODE CHARACTERISTICS

Additional Laser Caution

[ Important symbols for good services ]

4. Shipping mode and shipping screws

5. Lubricants, glues, and replacement parts

Manufactured under license from Dolby

Manufactured under license from Dolby

2. EXPLODED VIEWS AND PARTS LIST

PACKING parts List

(2) CONTRAST TABLE

15 Operating Instructions VRD1173 Not used

2.2 EXTERIOR SECTION

Refer to "2.4 LOADING MECHA ASSY".

Refer to "2.3 FRONT PANEL SECTION".

EXTERIOR SECTION parts List

(2) CONTRAST TABLE

31 PCB Holder VEC2215 Not used

48 Bonnet Case S VXX2847 VXX2848

2.3 FRONT PANEL SECTION

FRONT PANEL SECTION parts List

(2) CONTRAST TABLE

2.4 LOADING MECHA ASSY

" Application of Lubricant".

NSP 1 LOAB Assy VWG2346 16 Drive Gear VNL1923

6 Flexible Cable (26P) VDA1864 21 Screw JGZ17P028FMC

11 Loading Base VNL1917

Inner side of a ditch

Top View Bottom View

2.5 TRAVERSE MECHANISM ASSY-S

17 (Torque : 0.12 0.01 Nm)

TRAVERSE MECHANISM ASSY-S parts List

6 Guide Bar VLL1514

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM

B DVDM ASSY TK15404M 27M 22/24AV1

A LOAB ASSY IC251

LOADING CN601 CN103 14 3 13 9 10 15

F KEYB ASSY E FL TUBE

CN551 (2/2) CN101 (2/2) Y

7 POWER SUPPLY BLOCK

IC402 SW+5 V+5S V+5D

V+3D CN601 CN103

B DVDM ASSY E FLKY ASSY

3.2 LOAB ASSY and OVERALL WIRING DIAGRAM

3.3 DVDM ASSY 1/4 [FTS BLOCK]

(WYXJ : VWS1540) : RF (AUDIO) SIGNAL ROUTE

(RF_V) VCO Circuit

3.4 DVDM ASSY 2/4 [FR BLOCK]

B 2/4 DVDM ASSY

B 3/4 Clock Signals: Refer to "7.1.7 TEST POINT LOCATION A

3.5 DVDM ASSY 3/4 [EBY/AV1 BLOCK]

B 3/4 DVDM ASSY

: The power supply is shown with the marked box. A

B 1/4 (D) (D)

3.6 DVDM ASSY 4/4 [VENC BLOCK]

B 4/4 DVDM ASSY