The document describes a laboratory experiment to simulate an automatic sequential motion circuit for two pneumatic double-acting cylinders using FluidSim Pneumatic software. The objectives are to create a circuit where the cylinders retract alternately without retracting at the same time. It provides step-by-step instructions to build the circuit using directional control valves, cylinders, and to set the simulation.
The document describes a laboratory experiment to simulate an automatic sequential motion circuit for two pneumatic double-acting cylinders using FluidSim Pneumatic software. The objectives are to create a circuit where the cylinders retract alternately without retracting at the same time. It provides step-by-step instructions to build the circuit using directional control valves, cylinders, and to set the simulation.
The document describes a laboratory experiment to simulate an automatic sequential motion circuit for two pneumatic double-acting cylinders using FluidSim Pneumatic software. The objectives are to create a circuit where the cylinders retract alternately without retracting at the same time. It provides step-by-step instructions to build the circuit using directional control valves, cylinders, and to set the simulation.
The document describes a laboratory experiment to simulate an automatic sequential motion circuit for two pneumatic double-acting cylinders using FluidSim Pneumatic software. The objectives are to create a circuit where the cylinders retract alternately without retracting at the same time. It provides step-by-step instructions to build the circuit using directional control valves, cylinders, and to set the simulation.
At the end of the laboratory, you would be able to simulate, using FluidSim Pneumatic Software, a fully functional pneumatic circuit for automatic sequential motion of two pneumatic double-acting cylinder. Materials 3/2 way directional control valve, normally close push button, spring-returned 3/2 way directional control valve, normally open limit switch, with roller, spring-returned 5/2 way directional control valve, pneumatically actuated. Double-acting cylinder
Software FluidSim Pneumatic
Desired output
Our desired output will be an automatic sequential/ alternating retraction of piston in two pneumatic double-acting cylinders. So, both cylinders will not retract at the same time, but the double-acting cylinder #2 will be depend on the position of double-acting cylinder #1, either at 0 mm or at 100 mm (full retraction). Step-by-Step Guide Step 4: Double click the 2 five way valve and turn on the servo drive and spring return (left and right). Then, choose Step 1: Open the Pneumatic Developer App piloted as a valve actuation in both left and right. Click ok.
Step 6: Double click the 5 three way valve and turn on the servo drive and spring return (left and right). Then, select Step 2: Click the + button, then create a new project “Lever and Lever with lock” as a valve actuation on the left actuation.
Step 7: Connect the components by clicking the encircled
one. Then, double click the connection that is to be Step 3: Select and drag the devices to be used connected to the other connection. TWO Double-acting Cylinder TWO 5/2 way directional control valve FIVE 3/2 way directional control valve A Supply Step 8: Double click the connections that are not connected to others and choose exhaust not channeled connection option.
Step 9: Click the play button and watch the video.
Step 10: Then, start the simulation.
Step 11: Closed and save the project .
Laboratory 3
Deep-Well Drilling Machine
Name: ______________________ Date Submitted: ______________
Step 4: Double click the check valve to rotate 90°.
Step 2: Click the + button, then create a new project.
Step 3: Select and drag the devices to be used.
Step 5: Double click the five way valve and turn on the A Double-acting Cylinder servo drive and spring return (left and right). Then, select A 5/2 way directional control valve “button” as a valve actuation on the left actuation.Step 6: A Check valve Connect the components by clicking the encircled one. TWO Supply Then, double click the connection that is to be connected to the other connection.
Step 7: Double click the connections that are not
connected to others and choose escape channeled connection option. Step 8: Click the play button and watch the video.
Step 9: Then, start the simulation.
Step 10: : Closed and save the project .
Laboratory 4
Experimental Analysis of Electro-pneumatic Optimization
Name: ______________________ Date Submitted: ______________
Step 4: Double click the 2 five way valve and turn on the servo drive and spring return (left and right). Then, choose piloted as a valve actuation in both left and right. Click ok.
Step 2: Click the + button, then create a new project.
Step 5: Double click the 4 three way valve and turn on the servo drive and spring return (left and right). Then, select “Lever and Lever with lock” as a valve actuation on the left Step 3: Select and drag the devices to be used.
TWO Double-acting Cylinder
TWO 5/2 way directional control valve FOUR 3/2 way directional control valve A Regulator A Supply
actuation. Step 6: Connect the components by clicking the encircled one. Then, double click the connection that is to be
connected to the other connection. Step 8: Click the play button and watch the video.
Step 7: Double click the connections that are not
Step 9: Then, start the simulation.
connected to others and choose escape channeled
connection option. Step 10: : Closed and save the project . .
