EN

MC2
USER / INSTALLER MANUAL

v6.3
REV. 10/2019
 00. CONTENT 01. SAFETY INSTRUCTIONS
INDEX ATTENTION:

01. SAFETY INSTRUCTIONS This product is certified in accordance with European

2B
Community (EC) safety standards.
02. THE CONTROL BOARD
TECHNICAL SPECIFICATIONS 5A
This product complies with Directive 2011/65/EU of
PROGRAMMING PRE-RECOMENDATIONS 6A
the European Parliament and of the Council, of 8 June
03. CONFIGURATION 2011, on the restriction of the use of certain hazardous
MAIN MENU substances in electrical and electronic equipment.
7A
EXTENDED MENU 1 9B (Applicable in countries with recycling systems).
EXTENDED MENU 2 11A This marking on the product or literature indicates that
EXTENDED MENU 3 12B the product and electronic accessories (eg. Charger, USB
RESET OF CONTROL BOARD 13A cable, electronic material, controls, etc.) should not be
04. COMPONENT TEST disposed of as other household waste at the end of its
PHOTOCELLS TEST AND TRANSMITTERS 13A useful life. To avoid possible harm to the environment or
CAPACITATOR SCHEME 13B human health resulting from the uncontrolled disposal
05. TROUBLESHOOTING of waste, separate these items from other types of waste
INSTRUCTIONS FOR FINAL CONSUMERS 14 and recycle them responsibly to promote the sustainable
INSTRUCTIONS FOR SPECIALIZED INSTALLERS 14 reuse of material resources. Home users should contact
06. CONNECTION SCHEME the dealer where they purchased this product or the
COMPONENT'S CONNECTION TO THE CONTROL BOARD National Environment Agency for details on where and
15
how they can take these items for environmentally safe
recycling. Business users should contact their vendor
and check the terms and conditions of the purchase
agreement. This product and its electronic accessories
should not be mixed with other commercial waste.
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct
or indirect contact with electricity. Be cautious when
handling the product and observe all safety procedures
in this manual.
2A 2B
EN EN
 01. SAFETY INSTRUCTIONS
GENERAL WARNINGS who understands the risks and dangers involved.
• This manual contains very important safety and usage information. • Children shouldn’t play with the product or opening devices to
very important. Read all instructions carefully before beginning avoid the motorized door or gate from being triggered involuntarily.
the installation/usage procedures and keep this manual in a safe
place that it can be consulted whenever necessary. WARNINGS FOR TECHNICIANS
• This product is intended for use only as described in this manual. • Before beginning the installation procedures, make sure that you
Any other enforcement or operation that is not mentioned is have all the devices and materials necessary to complete the
expressly prohibited, as it may damage the product and put people installation of the product.
at risk causing serious injuries. • You should note your Protection Index (IP) and operating
• This manual is intended firstly for specialized technicians, and does temperature to ensure that is suitable for the installation site.
not invalidate the user’s responsibility to read the “User Norms” • Provide the manual of the product to the user and let them know
section in order to ensure the correct functioning of the product. how to handle it in an emergency.
• The installation and repair of this product may be done by qualified • If the automatism is installed on a gate with a pedestrian door,
and specialized technicians, to assure every procedure are carried a door locking mechanism must be installed while the gate is in
out in accordance with applicable rules and norms. Nonprofessional motion.
and inexperienced users are expressly prohibited of taking any • Do not install the product “upside down” or supported by elements
action, unless explicitly requested by specialized technicians to do do not support its weight. If necessary, add brackets at strategic
so. points to ensure the safety of the automatism.
• Installations must be frequently inspected for unbalance and the • Do not install the product in explosive site.
wear signals of the cables, springs, hinges, wheels, supports and • Safety devices must protect the possible crushing, cutting,
other mechanical assembly parts. transport and danger areas of the motorized door or gate.
• Do not use the product if it is necessary repair or adjustment is • Verify that the elements to be automated (gates, door, windows,
required. blinds, etc.) are in perfect function, aligned and level. Also verify if
• When performing maintenance, cleaning and replacement of the necessary mechanical stops are in the appropriate places.
parts, the product must be disconnected from power supply. Also • The central must be installed on a safe place of any fluid (rain,
including any operation that requires opening the product cover. moisture, etc.), dust and pests.
• The use, cleaning and maintenance of this product may be carried • You must route the various electrical cables through protective
out by any persons aged eight years old and over and persons tubes, to protect them against mechanical exertions, essentially
whose physical, sensorial or mental capacities are lower, or by on the power supply cable. Please note that all the cables must
persons without any knowledge of the product, provided that enter the central from the bottom.
these are supervision and instructions given by persons with • If the automatism is to be installed at a height of more than 2,5m
experienced in terms of usage of the product in a safe manner and from the ground or other level of access, the minimum safety and
3
EN
 01. SAFETY INSTRUCTIONS
health requirements for the use of work equipment workers at the the product is in motion.
work of Directive 2009/104/CE of European Parliament and of the
Council of 16 September 2009. RESPONSABILITY
• Attach the permanent label for the manual release as close as • Supplier disclaims any liability if:
possible to the release mechanism. • Product failure or deformation result from improper installation
• Disconnect means, such as a switch or circuit breaker on the use or maintenance!
electrical panel, must be provided on the product’s fixed power • Safety norms are not followed in the installation, use and
supply leads in accordance with the installation rules. maintenance of the product.
• If the product to be installed requires power supply of 230Vac or • Instructions in this manual are not followed.
110Vac, ensure that connection is to an electrical panel with ground • Damaged is caused by unauthorized modifications
connection. • In these cases, the warranty is voided.
• The product is only powered by low voltage satefy with central
(only at 24V motors)

WARNINGS FOR USERS

• Keep this manual in a safe place to be consulted whenever
necessary.
• If the product has contact with fluids without being prepared, it
must immediately disconnect from the power supply to avoid short
circuits, and consult a specialized technician.
• Ensure that technician has provided you the product manual and
informed you how to handle the product in an emergency.
• If the system requires any repair or modification, unlock the
automatism, turn off the power and do not use it until all safety
conditions have been met. SYMBOLS LEGEND:
• In the event of tripping of circuits breakers of fuse failure, locate
the malfunction and solve it before resetting the circuit breaker or • Important safety • Potentiometer
notices information
replacing the fuse. If the malfunction is not repairable by consult
this manual, contact a technician. • Useful information • Connectors
• Keep the operation area of the motorized gate free while the gate information
in in motion, and do not create strength to the gate movement. • Programming • Buttons
• Do not perform any operation on mechanical elements or hinges if information information
4
EN
 02. THE CONTROL BOARD 02. THE CONTROL BOARD
TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS

The MC2 is a central electronic single phase with incorporated radio, for automation of • CONNECTOR’S DESCRIPTION
swing gates.

• Power supply 110/230V AC 50-60Hz 01 • Earth connection

CN1
02 • Earth connection
• Lightbulb’s output 110/230V AC 500W máx.
03 • Earth connection
• Motor’s output 110/230V AC 50/60 Hz 500W máx.
01 • AC 110/230V Line Input (PHASE)
• Auxiliary accessories output 24V AC 15W máx. 02 • AC 110/230V Line Input (NEUTRAL)
03 • Lightbulb / Courtesy light’s output (not blink) AC110/230V (NEUTRAL)
• Safety and PB impulses 24V CC
04 • Lightbulb / Courtesy light’s output (not blink) AC110/230V (PHASE)
• Working temperature -10˚C to +55˚C 05 • Motor’s Output 1 opening

CN2
06 • Motor’s Output 1 common
• Protection IP56
07 • Motor’s Output 1 closing
• Incorporated Radio Receiver 433,92 Mhz 08 • Motor’s Output 2 opening
09 • Motor’s Output 2 common
• OP Transmitters 12-18 bits or Rolling Code
10 • Motor’s Output 2 closing
• Maximum memory capacity 150 (CODE or CODE PED)
01 • Output for power photocells 24V AC
• Fuses two 6.3A and 50mA fuses 02 • Output for power photocells (earth)
03 • Output for electric lock 12V DC 15W (+12V)
04 • Output for electric lock 12V DC 15W (earth)
05 • PUL input (button to order opening / closing) (NO)
• DIMENSIONS OF THE BOX AND CONTROL BOARD 06 • Earth common input

CN3
07 • PUL PED input (button to order pedestrian entry) (NO)
08 • DS1 Input safety device 1 (NC)
205mm 115mm 09 • Input common GND
10 • DS2 Input safety device 2 (NC)
11 • Antenna mass input
12 • Antenna hot pole input
125mm
252mm

140mm

5A 5B
EN EN
 02. THE CONTROL BOARD 02. THE CONTROL BOARD
PROGRAMMING PRE-RECOMENDATIONS PROGRAMMING PRE-RECOMENDATIONS

Before proceeding to the control board configuration, note the following points listed
• PROGRAMMING THE CONTROL BOARD - BUTTONS SEL/SET
in the table below:
SEL button: It makes the selection of the function to change. The se-
lection is identified by the flashing of the LED corresponding to the
selected function at that time.
Pressing the SEL button repeatedly will cycle through the various
SEL SET
functions to be programmed. The selection remains active for 10 se-
CN1 CN2 CN3
conds, after these time the control board returns to original status
(no active selection).
SET button: Makes programming the selected function through the
SEL button.
1 2 3 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 11 12
The SET button may be substituted by a remote control from the latter is pro-
grammed.

• POWER AND SPEED OF MOTORS

Lightbulb:
03 and 04 • This output allows connection of a lightbulb (see page 6B). The control board has a trimmer VR1 to adjust the force and speed of the
motors controlled by the microprocessor. The adjustment can be effec-
CN2

Capacitor: ted between 50% and 100% the power. - +

05 and 07 • Connect the capacitor between the outputs 05 and 07. At each start-up movement, the control board applies the maximum
08 and 10 • Connect the capacitor between the outputs 08 and 10. power during 2 seconds, even when it is made regulating force to a value FORZA
than not the maximum.
Electric lock:
03 and 04 • This output allows connection of an electric lock (see pág.11A) When you adjust the trimmer VR1 has to remake course programming, as they
could varied the times of maneuvering and deceleration.
Push button / selector:
05 • Allows connection the push-button / selector to full opening (NO). • OPERATION OF LIGHTBULB
06 • Allows connection the push-button / selector to full opening (NO).
The operation of the output is conditioned by the mo- CN2
Safety circuits: vement of the motor and automatic closing. When the
08 • This circuit allows the connection of all types of safety devices such as automatic closing is activated, the 110/230V output is
CN3

photocells, safety edge, etc. activated even during pause time.

This device operates only in the gate closing maneuver and, when activated, it 3 4
reverses the direction of the automatism.
• OPERATION WITH TIMER
10 • This circuit allows the connection of all types of safety devices such as Instead of a opening / closing (PUL) push button, the CN3
photocells, safety edge, etc. control board can be operated with a TIMER. With a
This device operates in the opening and closing maneuvers. In the closing TIMER connected to the control board it is possible to
maneuver, it reverses the direction of the automatism. In the opening maneuver, program an exact time for the motor to perform both
it stops the movement and, when it is released, the opening continues. the opening and the closing, in automatic mode. 5 6

6A 6B
EN EN
 03. CONFIGURATION 03. CONFIGURATION
MAIN MENU MAIN MENU

This is the main menu of the control board MC2, which has access to the most impor- closing. If the gate is stopped during the closing maneuver, it will stop and will restart
tant functions of its operation. The control board is supplied with the active main menu. only when receive a new order.
Select operating mode:
MAIN MENU
01. Press the SEL button once, and the AUT / P-P LED will start to flash.
LED LED OFF LED aceso 02. Press the SET button for 1 second.
03. The AUT/PP LED ON means that the "step by step" mode is selected. The AUT/PP LED
• AUT/P-P Automatic Step by step
OFF means that the "automatic" mode is selected.
• CODE No code Inserted code
• CODE | TRANSMITTER PROGRAMMING
• CODE PED. No code Inserted code
The control board accepts only Dip-Switch or Rolling Code MOTORLINE transmitters, and
• INB. CMD. AP Deactivated Activated has a maximum capacity of 150. When trying to program the 151º transmitter, all the pro-
gramming LEDs will flash simultaneously to indicate that the memory is full.
• T. MOT. Motor time 30 s. Programmed time
To program new transmitters:
• T. MOT. PED Motor time pedestrian 10 s. Programmed time
01. Press the SEL button as many times as necessary until the CODE LED flashes.
• T. PAUSA. Without automatic closing With automatic closing 02. Press once the transmitter's button you want to program for 1 second.
03. The LED CODE lights up permanently, indicating the successful of the programming.
• T. RIT. ANTE No delay Programmed time
To delete all configured transmitters:
01. Press the SEL button once, and the CODE LED will begin to flash.
• AUT/P-P | AUTOMATIC OPERATION / STEP BY STEP 02. Press the SET button once. The CODE LED turns off and all transmitters have been
Automatic operating mode (LED AUT / P-P OFF): deleted.
• The first impulse of the remote control / push-button activates the opening movement
until the end of the motor's time. If the CODE LED starts to flash quickly, means that the control board did not accept the
• The second impulse of the remote control / push-button activates the closing moven- transmitters code, because of the following reasons:
ment until the end of the motor's time. • The transmitter is already programmed;
If an order is given before the end of the motor time, the control board will perform a in- • The control board accepts only Rolling Code transmitters.
version of movement in opening and closing.

Mode of operation step by step (LED AUT / P-P on):

• The first impulse of the remote control / push-button activates the opening movement • CODE PED | PEDESTRIAN OPERATION
until the end of the motor's time. The control board allows to start only one motor in order to permit pedestrian passage.
• The second impulse of the remote control / push-button activates the closing moven- With this function, pressing the transmitter, will only open the door with the motor 1.
ment until the end of the motor's time.
If an order is given before the end of the motor time, the control board will stop the move- Programming the transmitters to pedestrian mode (CODE PED LED ON) / erase transmi-
ment in opening and closing. A new order will return the operation, performed in the other tter (CODE PED LED OFF):
direction to what it was before the stop. 01. Press the SEL button once until the CODE PED LED starts to flash.
The control unit is supplied by the manufacturer with the activated Automatic mode (LED 02. Press the transmitter's button that you want to program during 1 second.
AUT / P-P off). If you want delete transmitters, press the SET button for 1 second.
Note: If the T. PAUSE is active (on) and the gate is stopped during the opening maneuver, 03. The CODE PED LED ON indicates that the transmitter is programmed and the CODE
the gate will stay stopped until the end of the pause time, and after that it will make the PED LED OFF indicates that the transmitters have been deleted.

7A 7B
EN EN
 03. CONFIGURATION 03. CONFIGURATION
MAIN MENU MAIN MENU

• INB. CMD. AP | TRANSMITTER INHIBITION DURING THE OPENING AND PAUSE TIME Program working time of the motor without deceleration (Gate closed):
01. Press the SEL button the times necessary until the LED T.MOT. start to flash.
With the function activated, the control board rejects all the transmitters signals during
02. Press the SET button for 1 second, so that the Motor 1 start opening. If the motor
the opening maneuvers and automatic pause time. It’s important that this function is
does not accept the opening, invert the cable connections 5 and 7, the CN2 connector
activated during the magnetic loop installation, because the control board will ignore
(see page 4B).
the crossings performed during the opening and the pause time.
03. Press twice the SET button when the gate is in the desired point to finish the opening
The control board is supplied by the manufacturer with this function deactivated.
course. At this time, LED T. MOT. will quickly flashing and automatically the motor 2 starts
Activate (LED ON) / deactivate (LED OFF) function: opening maneuver.
01. Press the SEL button the times necessary until the INB CMD AP LED starts to flash. 04. Press SET button two times when desires to establish the opening limit switch.
02. Press SET button for 1 second to enable / disable the function. 05. The T. MOT. will quickly flashing indicating that programming for closing can be per-
03. The INB CMD LED AP ON indicates that the function is active and the LED OFF indi- formed and automatically the motor 2 starts the closing maneuver. Repeat the process
cates that the function is deactivated. to program the closing.

• T. MOT. PED | PROGRAMMING PEDESTRIAN WORKING TIME

• T. MOT AND DECELERATION | MOTOR TIME PROGRAMMING AND DECELERATION
To activate the pedestrian function, the control board allows to be just activated the
With this function, it's possible to thrigger the slowdown, decreasing the gate's move- operation of motor 1.
ment speed.
NOTE • To perform this programming is necessary that the motors have limit-switches
NOTE • To perform this programming is necessary that the motors have limit-switch or
or stoppers.
mechanical stop.
Instead of using the SET button on the control board, you can use a transmi that is
Instead of using the SET button of the control board, you can use a trasmitter that is
already programmed.
already programmed.
The control board is supplied by the manufacturer with a pedestrian working time es-
The control board is supplied by the manufacturer with a working time of motors estab-
tablished in 10 seconds without deceleration.
lished within 30 seconds, without deceleration.
Programming pedestrian working time with deceleration (gates closed):
Program working time of the motor with deceleration (Gate closed):
01. Press the SEL button the times necessary until the LED T.MOT. start to flash. 01. Press SEL button as often as necessary until the T. MOT. PED. LED starts to flash.
02. Press the SET button for 1 second, so that the Motor 1 start opening. If the motor 02. Press the SET button for 1 second, so that the Motor 1 starts to open. If the motor
does not accept the opening, invert the cable connections 5 and 7, the CN2 connector does not accept the opening, invert the cable connections 5 and 7, the CN2 connector
(see page 4B). (see page 4B).
03. Press the SET button for 1 second, when the gate is at the desired point to start de- 03. Press the SET button for 1 second, when the gate is the desired point to start de-
celeration. celeration.
04. Press again SET button when you want to establish the opening limit-switch. At this 04. Press again SET button when you want to establish the opening limit-switch. At
time, T. MOT. LED will quickly flash and automatically the motor 2 will start the opening this time, T. MOT. PED. LED will quickly flashing and automatically the motor 1 starts
maneuver. closing maneuver.
05. Press the SET button for 1 second, when the gate is at the desired point to start de- 05. Press the SET button when the gate is at the desired point to start deceleration.
celeration. 06. Press again SET button when you want to establish the closing limit-switch.
06. Press again SET button when you want to establish the opening limit-switch. 07. The T. MOT. PED. LED will light, signaling that the working time is programmed.
07. The T. MOT.LED will quickly flash indicating that programming for closing can be per-
formed and automatically the motor 2 starts the closing maneuver. Repeat the process
to program the closing.

8A 8B
EN EN
 03. CONFIGURATION 03. CONFIGURATION
MAIN MENU MAIN MENU
Programming pedestrian working time without deceleration (gates closed): Programming:
01. Press SEL button as often as necessary until the T. MOT. PED. LED starts flashing. 01. Press the SEL button as often as necessary until the LED T. RIT. ANTE starts flashing.
02. Press the SET button for 1 second, so that the Motor 1 start opening. If the motor 02. Press the SET button for 1 second. From that moment, the waiting time before pres-
does not accept the opening, invert the cable connections 5 and 7, the CN2 connector sing SET will be equal to the time that the gate stays open.
(see page 4B). 03. Press the SET button for 1 second, when you reach the time that you want. Therefo-
03. Press twice the SET button, when you want to establish the opening limit switch. re, on closing, the delay time will be stipulated by the option while the opening is fixed
At this time, LED T. MOT. LED will quickly flashing and automatically the motor 1 starts in 2 seconds.
closing maneuver. 04. The LED T. RIT. ANTE will light permanently, indicating the memorization time delay
04. Press twice the SET button when you want to establish the closing limit switch. between motor 1 and motor 2.
05. The LED T. MOT. LED will light, signaling that the working time is programmed.
Delete programming:
01. Press the SEL button until the LED T. RIT. ANTE will flashing.
02. Press the SET button twice in less than 2 seconds.
• T. PAUSA | PROGRAMMING AUTOMATIC CLOSING 03. The LED T. RIT. ANTE will off, signaling the success of the operation.
The control board permits an automatic closing after a set waiting time, maximum until
4 minutes.
The control board is supplied by the manufacturer with this function disabled.
EXTENDED MENU 1
NOTE • Instead of using the SET button on the control board, you can use a remote
control that is already programmed. The control board is supplied by the manufacturer with an extended menu 1, which
allows access to more functions of the control board.
Activate (LED ON)/deactivate (LED OFF) function:
1. Press SEL button as often as necessary until the LED T. PAUSA starts flashing. To access the options of extended menu 1 follow these instructions:
2. Press the SET button for 1 second. From that moment, the waiting time before pres- 01. Press continuously the SET button for 5 seconds and the LED T.PAUSA and LED T.
sing SET will be equal to the time that the gate stays open. RIT. ANTE will flash alternately.
3. Press the SET button for 1 second, when you reach the time that you want for the 02. You have 30 seconds to select functions from the extended menu 1 (using the SEL
automatic closing. and SET button), and that after this time the control board returns to main menu.
4. The LED T.PAUSA ON indicates that the function is active and the LED off indicates
that the function is disabled. EXTENDED MENU 1
LED LED OFF LED ON
Delete programming:
01. Press the SEL button until the LED T. PAUSA will flashing.
• AUT/P.P. PGM distance OFF PGM distance ON
02. Press the SET button twice in less than 2 seconds. • CODE Photocells test ON Photocells test OFF
03. The LED T. PAUSA will off, signaling the success of the operation.
• CODE PED. Pressure maintenance OFF Pressure maintenance ON
• INB. CMD. AP Opening push OFF Opening push ON
• T. RIT. ANTE | PROGRAMMING DOOR DELAY
• T. MOT. Closing push OFF Closing push ON
This function can delay up to 30 seconds the start of the closing motor 1 in relation to
the motor 2. • T. MOT. PED Safety device 2 Blockade entrance
At the opening, the difference between the motor starting motor 2 to 1 is always 2 se-
• T. PAUSA. Alternative intermittence ON/OFF
conds.
The unit is supplied by the manufacturer with this function disabled. • T. RIT. ANTE Alternative intermittence ON/OFF

9A 9B
EN EN
 03. CONFIGURATION 03. CONFIGURATION
EXTENDED MENU 1 EXTENDED MENU 1

• AUT/P-P | PROGRAMMING OF THE REMOTE CONTROL ON DISTANCE 03. Press SET button for 1 second.
The programming the transmitter at distance function, allows them to be added remote 04. The CODE PED LED ON indicates that the function is activated and the CODE PED
controls to the new control board without having to use the SEL button. The control LED OFF indicates that the function is disabled.
board is supplied by the manufacturer with programming remote controls on distance
deactivated. • INB. CMD. AP. | OPENING PUSH
Activate (LED ON) / deactivate (LED OFF) function: The opening push function, facilitates the release of the lock when the opening is ac-
01. Activate the extended menu 1. tuated, ensuring proper operation.
02. Press SEL button once and the AUT/P-P LED will begin to flash. The control board is supplied by the manufacturer with the opening push disabled.
03. Press for 1 second the SET button. Activate (LED ON)/deactivate (LED OFF) function:
04. AUT/P-P LED ON indicates that the function is active and the AUT/P-P LED OFF 01. Activate the extended menu 1.
indicates that the function is disabled. 02. Press SEL button as often as necessary until the INB. CMD. AP. LED start to flash
Programming of transmitters on distance: 03. Press SET button for 1 second
01. Press for 10 seconds the button of the remote control a previously memorized. 04. The INB. CMD. AP LED ON indicates that the function is activated and the INB.
02. LED CODE will flash. CMD. AP LED OFF indicates that the function is disabled.
03. Press for 1 second one button of the remote control that you want to program.
04. The flash lamp will flash confirming the success of the operation.

• T. MOT. | CLOSING PUSH

• CODE | TEST OF PHOTOCELLS With the closing push function, the control board case is programmed with decele-
The control board is supplied by the manufacturer with the photocells test deactivated. ration, will add 1 second acting at full motor power, so that the gate can overcome
the lock.
Activate (LED ON)/deactivate (LED OFF) function:
The control board is supplied by the manufacturer with the closing push disabled.
01. Activate the extended menu 1
02. Press SEL button once and the LED AUT/P-P will begin to flash.
Activate (LED ON)/deactivate (LED OFF) function:
03. Press SET button for 1 second
04. The LED CODE ON indicates that the function is disabled and the LED off indicates 01. Activate the extended menu 1.
that the function is activated. 02. Press SEL button as often as necessary until the LED T. MOT. starts to flash.
NOTE • If you do not have the photocells installed, this test will not work. 03. Press SET button for 1 second
04. The LED T.MOT. ON indicates that the function is activated and the LED T.MOT.
OFF indicates that the function is disabled.
• CODE PED | MOTORS PRESSURE
The pressure of the motors function, makes the control board to send closing orders for
2 seconds, once every two hours.
• T. MOT. PED | SAFETY DEVICE 2 / BLOCKING
The control board is supplied by the manufacturer with the hydraulic motors pressure
functionality OFF. With the blocking function activated whenever the photocells (DS2) detected an obsta-
cle, the gate movement will stop and will only triggered when you press the transmitter
Activate (LED ON)/deactivate (LED OFF) function: button. Before the gate resume movements, the lightbulb will flash during 5 seconds.
01. Activate the extended menu 1. The control board is supplied by the manufacturer with blocking function disabled.
02. Press SEL button as often as necessary until the CODE PED LED starts to flash.

10A 10B
EN EN
 03. CONFIGURATION 03. CONFIGURATION
EXTENDED MENU 1 EXTENDED MENU 2

Activate (LED ON) / deactivate (LED OFF) function: • AUT/P-P | FOLLOW ME

01. Activate the extended menu 1.
02. Press SEL button as often as necessary until the T. MOT. PED. LED starts to flash. With the pause time programmed, it is possible to trigger "Follow Me" option.
03. Press SET button for 1 second. With this option enabled, whenever the photocells detected the passage of a user/
04. The T. MOT. PED. LED ON indicates that the function is activated and the T. MOT. PED. object, the control board triggers the closing maneuver after 5 seconds.
LED OFF indicates that the function is disabled.
Activate (LED ON) / deactivate (LED OFF) function:
01. Enter the extended menu 2.
02. Press once the SET button and the AUT/P-P LED starts flash.
03. Press once SET button to enable / disable the function.
EXTENDED MENU 2
The AUT/PP LED ON signals that the function is activated and the AUT/PP LED OFF
signals that the function is disabled.
The control board is supplied by the manufacturer with an extended menu 2, which
provides access to more functions to the control board.
• CODE | PRE LIGHTBULB/LAMP.CORT
To access the extended menu 2 options proceed as follows: With the functioning in pre lightbulb, the output 03 and 04 (CN2) will always be activa-
01. Enter the extended menu 1 (see page 06.B). ted 3 seconds before the automation start a movement. When disabled, the function
02. Press continuously the SET button for 5 seconds and the T.PAUSA and T. RIT. returns lightbulb.
ANTE LEDs will flash simultaneously. The control board is supplied by the manufacturer with the pre lightbulb disabled.
03. You have 30 seconds to select functions from the extended menu 2 (using the
Activate (LED ON)/deactivate (LED OFF) function:
SEL and SET button), and after this time the control board returns to the main menu.
01. Enter the extended menu 2.
02. Press SEL button as often as necessary until the LED CODE starts to flash.
03. Press once SET button to enable / disable the function.
EXTENDED MENU 2 The LED CODE ON signals that the function is activated and the LED CODE OFF signals
LED LED OFF LED ON that the function is disabled.
• AUT/P.P. Follow Me OFF Follow Me ON
• CODE Pre Lightbulb OFF Pre Lightbulb ON • CODE PED | OPERATION OF OUTPUT 110/230V FOR LIGHTBULB DURING THE PAUSE TIME
With this option enabled, whenever the motor is in pause time at output 110/230V for
• CODE PED. Lightbulb on pause OFF Lightbulb on pause ON
lightbulb will stay on.
• INB. CMD. AP Soft start OFF Soft start ON The control board is supplied by the manufacturer with the lightbulb during pause time,
disabled.
• T. MOT. Electronic lock PED OFF Electronic lock PED ON
• T. MOT. PED PUL=PUL | PED=PED PUL=AB | PED=FECH Activate (LED ON) / deactivate (LED OFF) function:
01. Enter the extended menu 2.
• T. PAUSA. Intermittent simultaneously 02. Press SEL button as often as necessary until the LED CODE PED starts to flash.
• T. RIT. ANTE Intermittent simultaneously 03. Press once SET button to enable / disable the function.
The LED CODE PED ON indicates that the function is activated and the LED OFF signals
that the function is disabled.

11A 11B
EN EN
 03. CONFIGURATION 03. CONFIGURATION
EXTENDED MENU 2 EXTENDED MENU 2

• INB. CMD. AP. | SOFT START PUL= opening, PED= closing (LED ON) / PUL=PUL and PED=PED (LED OFF):
With function "Soft Start" enabled, the beginning of each movement, the control board 01. Enter the extended menu 2.
will control start the motor, increasing power gradually in the first 2 seconds of opera- 02. Press SEL button as often as necessary until the LED T. MOT. PED starts to flash.
tion. 03. Press once SET button to change the function.
The control board is supplied by the manufacturer with the "Soft Start" disabled. The T. MOT. PED LED ON signals that the PUL is programmed for opening and PED for
closing. The T. MOT. PED LED OFF indicates that the function PUL is programmed to
Activate (LED ON) / deactivate (LED OFF) function: function with a main cyclic push-button (NO) and the PED input to connect a pedes-
01. Enter the extended menu 2. trian cyclic push-button (NO).
02. Press SEL button as often as necessary until the LED INB. CMD. AP. starts to flash.
03. Press once SET button to enable / disable the function.
The INB. CMD. AP. LED ON indicates that the function is activated and the INB. CMD. AP.
LED OFF signals that the function is disabled.
EXTENDED MENU 3

• T. MOT. | ELECTRONIC LOCK IN PEDESTRIAN FUNCTION With the extended menu 3 can program the power / motor speed at which will be per-
The electronic lock in pedestrian function is used when there is, for example, a swing formed the deceleration.
doors assembled with electric lock to close the door 2. This makes it possible to
obtain the opening of the gate by trigger a push-button connected in PUL, PED or to To access the Extended menu 3 options proceed as follows:
trigger the remote control. 01. Enter the extended menu 1 (see page 06.B).
The transmitter is supplied by the manufacturer with the electronic lock on the pe- 02. Enter the extended menu 2 (see page 08.A).
destrian function disabled. 03. Continuously press the SET button for 5 seconds and the T.PAUSA and T. RIT. ANTE
LEDs will flash alternately for a few moments and flash simultaneously afterwards.
Activate (LED ON)/deactivate (LED OFF) function: 04. You have 30 seconds to select from the extended menu 3 functions (using the SEL
01. Enter the extended menu 2. and SET button), and after this time the control board returns to the main menu.
02. Press SEL button as often as necessary until the T. MOT. LED start to flash.
03. Press once SET button to enable / disable the function.
The T. MOT. LED ON indicates that the function is activated and the T. MOT. LED OFF
signals that the function is disabled. EXTENDED MENU 3
LEVEL OF THE POWER LEDS ON
1 AUT/P-P.
• T. MOT. PED | OPERATIONS THE INPUTS PUL AND PED 2 AUT/P-P. • CODE
The control board permits that the PUL input work with a push button (NA) exclusi-
3 AUT/P-P. • CODE • CODE PED
vely for opening and PED input work with a push button (NA) only for closing.
The control board is supplied by the manufacturer with the operation of the PUL 4 AUT/P-P. • CODE • CODE PED • INB. CMD. AP
input for connection to a primary push-button (NA) cyclic and PED input for connec-
5 AUT/P-P. • CODE • CODE PED • INB. CMD. AP • T. MOT.
ting a pedestrian pushbutton (NA) cyclic.
01 6 AUT/P-P. • CODE • CODE PED • INB. CMD. AP • T. MOT. • T. MOT. PED

12A 12B
EN EN
 03. CONFIGURATION 04. COMPONENT TEST
EXTENDED MENU 3 CAPACITORS CONNECTION SCHEME

Motor power programming during the deceleration: To detect if the malfunction is on the control board or on the motor is, sometimes,
It is possible to choose up to 6 different levels, relatively the force that the motor per- necessary to perform tests with connection directly to a 110/230V power supply.
forms in deceleration. The levels are represented by combinations of the LED indicated For this, it is necessary to interpose a capacitor on the connection in order to the
in the table above. automatism to work (check the type of capacitor to be used in the product manual).
Scroll through the LEDs with the SEL button to set the desired power, knowing that the The diagram below, shows how to make that connection and how to merge the different
LED AUT / P-P. ON corresponds to minimum power, while the LEDs AUT / P-P., CODE, components wires.
CODE PED, INB. CMD. AP, T. MOT., T. MOT. PED ON correspond to maximum power.
NOTES:
The control board is supplied by the manufacturer with the power regulated at level 3
> To perform the tests, there is no need to remove the automatism from the place it is instal-
(AUT / P-P., CODE, CODE PED ON). led, because in this way, it is possible to understand if the automatism can function properly
connected directly to the current.
> You should use a new capacitor during this test to ensure that the problem does not lie on it.

RESET TO CONTROL BOARD 01 • Connect the power wires to the terminal, as shown below.
02 • Connect the automatism wires in the terminal, interposing a capacitor in the
opening and closing wires.
If you need to restore control board to the factory setting, press the SEL and SET but-
03 • Once these connections are completed, connect to a 110/230V power outlet,
tons simultaneously. All LEDs will light up temporarily, and when erased, the success
depending on the motor/control board in test.
of the operation is confirmed.

Close Phase 1
Power Supply 1
Motor
PHOTOCELLS AND CONTROLS TEST COM
COM 1

COM 2 3
Open
Power Supply 2
• PHOTOCELLS TEST Phase 2
The control board is prepared to a safety device connection in accordance with the sec-
Ground Wire
tion 5.1.1.6 of standard EN 12453. In every maneuver is performed a test for the Security
8μF
Device and the Lock. In case of a function/connection failure the motor doesn’t start Capacitor
and every LED’s remain in a intermittent mode, indicating the error. When the photoce-
lls operation is corrected, the control board returns to it’s normal functioning. This ac- 1
tion by the control board allows to recognize failures in accordance with is mentioned 2
in category 2 of EN 954-1. 2
AUTOMATISM

• TRANSMITTER'S TEST
In the position corresponding to each transmitter input in low voltage, the control
This test only applies to 110/230V motors. To test a 24V motor, just connect
board has a LED to identify the condition of it. The LED ON indicates that the input is
the motor cables to a 24V battery.
closed, while the LED OFF indicates that the input is open.

13A 13B
EN EN
 05. TROUBLESHOOTING
FINAL CONSUMERS INSTRUCTIONS INSTRUCTIONS FOR SPECIALIZED INSTALLERS

Anomaly Procedure Behavior Procedure II Discovering the origin of the problem

• Motor • Make sure you have • Still not working • Consult a qualified 1 • Open control board and check 3 • Disconnect the motor from 4 • If the motor works, the 5 • If the motor doesn’t work,
doesn't work 110/230V power MOTORLINE technician. if it hás 110/230V power supply; control board and test them by problem is on the control board. remove them from installation
supply connected to connecting directly to power Pull it out and send it to our site and send to our MOTORLINE
automation and if it is 2 • Check the control board input supply in order to find out if they MOTORLINE technical services technical services for diagnosis.
working properly. fuses; have problems for diagnosis;
(see page 10.B).
• Motor • Unlock motor and • Encountered • Consult an experienced 1 • Check all motion axis and associated motion systems related with the motor and the gate to find out what is the problem.
doesn’t move move the gate by hand problems? gate expert.
but makes to check for mechani-
noise cal problems on the • The gate moves • Consult a qualified 1 • Check capacitors, testing 2 • If capacitors are not the 3 • If the motors work, the 4 • If the motors doesn’t work,
movement. easily? MOTORLINE technician. operator with new capacitors; problem, disconnect motors from problem is from control board. remove them from installation
control board and test them by Pull it out and send it to our site and send to our MOTORLINE
connecting directly to power technical services for diagnosis; technical services for diagnosis.
supply in order to find out if they
have problems (see page 10.B);
• Motor opens • Unlock motor and • Gate opened but 1 • Check if there is any All MOTORLINE control boards have LEDs that A) SECURITY SYSTEMS: B) SISTEMAS DE START:
but doesn’t move the gate by hand didn’t close again. obstacle in front of the easily allow to conclude which devices are
close to closed position. photocells; with anomalies. All safety devices LEDs (DS) 1 • Close with a shunt all safety systems 1 • Disconnect all wires from START terminal
Lock motor again and 2 • Check if any of the control in normal situations remain On. All "START" on the control board (check manual of the input.
turn off power supply devices (key selector, push circuits LEDs in normal situations remain Off. control board in question). If the automated
for 5 seconds. Recon- button, video intercom, etc.) system starts working normally check for the 2 • If the LED turned Off, try reconnecting one
nect it and send order of the gate are jammed and If LEDs devices are not all On, there is some problematic device. device at a time until you find the defective
to open gate using sending permanent signal to security systems malfunction (photocells, device.
transmi- tter. control unit; safety edges), etc. If "START" circuits LEDs 2 • Remove one shunt at a time until you find
3 • Consult a qualified are turn On, there is a control device sending the malfunction device. NOTE: In case procedures described in
MOTORLINE technician permanent signal. sections A) and B) don’t result, remove control
3 • Replace it for a functional device and board and send to our technical services for
check if the motor works correctly with all the diagnosis.
other devices. If you find another one
defective, follow the same steps until you find
all the problems.

• Gate doesn’t • Unlock motor and • Encountered • Consult an experienced 1 • Check all motion axis and associated motion systems related with the gate to find out what is the problem.
make move gate by hand to problems? gate expert.
complete check for mechanical
route problems on the gate. • The gate moves • Consult a qualified 1 • Check capacitors, testing with and send to our MOTORLINE 5 • If this doesn’t work, remove NOTE:
easily? MOTORLINE technician. new capacitors; technical services for diagnosis. control unit and send it to Setting force of the controller
MOTORLINE technical services should be sufficient to make the
2 • If capacitors are not the 4 • If motor work well and move services. gate open and close without
problem, disconnect motor gate at full force during the entire stopping, but should stop and
from control board and test it course, the problem is from invert with a little effort from a
by connecting directly to power controller. Set force using person. In case of safety systems
supply in order to find out if it is trimmer on the board. Make a failure, the gate shall never cause
broken; new working time programming , physical damaged to obstacles
giving suffient time for opening (vehicles, people, etc.).
3 • If the motor doesn’t work, and closing with appropriate
remove it from installation site force (page 08.B).

14
EN
 T.RIT.ANT
T. PAUSA
T.MOT.PED
T.MOTOR
INB.CMD.AP
CODE PED
CODE
AUT/P-P

SEL SET

- Force +
06. CONNECTION SCHEME

PUL PED DS1 DS2

1 2 3 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 11 12

LAMP MOTORE 1 MOTORE 2

230V AP COM CH AP COM CH V PUL PED DS 1D 1DS2
L N SERR.
COMPONENT'S CONNECTION TO THE CONTROL BOARD

PL L N
Lock
Blue
Blue

Black
Black

Brown
Brown

Earth wire
Earth wire
Light Bulb Antenna

Complete Pedestrian
Opening (2 Opening (1
doors) door)

K1 K2
Exterior Photocells
10V 12/24V
2 10V 12/24V COM
2 3 NC 4 5

2 0V 12/24V COM
2 COM
3 NC 5
4 NO NC
-10V 12/24V
+ 1- +

~ ~ ~ ~
Motor 1 Motor 2 K1 K2

Interior Photocells
10V 12/24V
2 10V 12/24V COM
2 3 NC 4 5
- Motor 1 starts opening before Motor 2 -
- Motor 2 starts closing before Motor 1 - + - + COM NC NO

- A capacitor must be intercalated in each

motor. Please, consult the product's
manual to check the capacity and how to
connect it.
NOTE • If any one of the motors move in
the wrong way, just switch the brown and If you don't use photocells it's
black cables of that motor to change the necessary the application of shunts.
direction.
EN
15