ConServ Rig 6

Well Servicing / Workover Derrick

Rigs

CONTRACTOR SERVICES INC Technical Data Sheet
929 CHARLESTON ROAD
SPENCER, WV 25276
P: 304‐927‐5033
F: 304‐927‐5068
RIG #6 DICKIRSON/KSM K‐550

FEATURES AND SPECIFICATIONS

Mast Rating: Maximum hook load capacity: 220,000 lbs. Main Drum Cont. Chain guards fully enclosed with inspection

with 6 lines, 185,000 lbs. with 4 lines covers and site glasses. Self‐equalizing
brake system complete with guards, rollers,
Main Drum: 16” diameter X 36 ¾” long drum. Main springs and adjustable equalizers provide
drum rims 42” X 10” wide. Drum brake for full release of drawworks brakes with
blocks 1” thick X 10” wide X 12” long (330 simple adjustment. All bell cranks have
degrees of wrap). Brake flanges heat treated grease nipples. Main drum line has Lebus
and hardened, brinnel hardness tested, split sleeve grooved for 1” drill line with
demountable type double‐lipped for water replaceable wear plates and drill line
splash cooling. Auxiliary 40” air cooled disc kickers. Includes one plain steel open side

brake with air powered brake caliper. Drum anchor complete with drilling line clamps to
shafts are 4140 chrome moly manganese be used with deflection type load cell and
steel, heat‐treated, stress relieved, with weight indicator. Right angle drive has high
double row self‐aligning spherical roller capacity oil bath gears, shafts mounted on
bearings. Fawick (Eaton Yale) 32” CB525 heavy‐duty bearing, with integral power
drum clutch. 1 ¼” pitch triple roller input shaft and tubular housing support with
drive chain, and 2” pitch single roller inner extended shaft for optional rotary drive.
drum drive chain.

FEATURES AND SPECIFICATIONS (continued)

Sandline Drum: Provisions only, as required for future Chain Case: One KSM two shaft oil bath rotary drive
installation of sand line drum, including chain mounted on carrier with sprockets,
brake system and controls. flanges, chains, and support equipment.
Operator Controls: All Rexroth air controls are centrally located Kelly Spinner: Stand pipes (1” XH SMLS) complete with

in a panel with hinged door at rear for easy hosing to control in driller’s console. Hoses
access to valves with a union at the bottom from gooseneck on top of standpipes to
for easy removal to different operating Kelly Spinner not included.
locations. Air is taken from main air
distribution block located in panel. All Stand Pipe and
controls are tagged with ID plates. Manifold: One 3” stand pipe comes complete with
gooseneck 5,000 psi working pressure. The
Mast Pole: Telescoping type mast, 104’ high when fully stand pipe is clamped to the mast. Includes
extended. Includes: (1) three sheave connection to front of rig at front bumper.
assembly, 24” diameter, and grooved for 1”
line, (2) one sheave assemblies, 24” Units Available: (1) 2007 Dickirson/KSM 550 RIG #6
diameter, grooved for 1” line, and (1)
provision for sandline sheave assembly, 20”

diameter, and grooved for 9/16” line.
Includes: crown saver assembly, (1) racking
board with 10,000 ft tubing capacity, and (1)
rod board.
Power Unit: Detroit 60 series 6063‐HV39 turbo diesel
engine, industrial type, rated for 475 hp @
2,100 rpm. Includes a Bendix Tuflo 750 air
compressor.
Transmission: Allison CLT5861‐5 transmission with TC680
torque converter, and Chelsea
852XBAKPF4XS power take‐off unit.
Hydraulic System: Commercial P37X378BYJC20‐7BIT15‐1
hydraulic gear pump 50 gpm and 2,000 psi
rated. 150 gallon reservoir. Driven from
transmission PTO.
Supplies power for leveling jacks, winch
mast hoist, and power tongs.
Winches: (2) Braden BG8B34029‐01‐1 winches
Rotary Drive: One KSM heavy‐duty torque tube rotary
drive with a KSM reversing box, twin disc
PO214 clutch and drive line to the rear of
the rig with control valve in operator’s
panel.

Hydraulic Catworks: One 60” makeup and one 60” breakout
hydraulic catwork cylinder mounted in the
mast with hydraulic controls and lineguide
rollers.
Tong Counterweight: Two tong counterweights mounted in mast.

ConServ Rig 6

Uploaded by

Copyright:

Available Formats

ConServ Rig 6

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ConServ Rig 6

Uploaded by

Copyright:

Available Formats

Mast Rating: Maximum hook load capacity: 220,000 lbs. Main Drum Cont. Chain guards fully enclosed with inspection

Operator Controls: All Rexroth air controls are centrally located Kelly Spinner: Stand pipes (1” XH SMLS) complete with

You might also like