Instrument Flight Planning: Naval Air Training Command
Instrument Flight Planning: Naval Air Training Command
Instrument Flight Planning: Naval Air Training Command
INSTRUMENT
FLIGHT PLANNING
WORKBOOK
T-6B
2022
DEPARTMENT OF THE NAVY
CHIEF OF NAVAL AIR TRAINING
250 LEXINGTON BLVD SUITE 179
CORPUS CHRISTI TX 78419-5041
CNATRA P-771
N716
04 Jan 22
1. CNATRA P-771 (Rev. 01-22),"Instrument Flight Planning Workbook, T-6B" is issued for
information, standardization of instruction and guidance for all flight instructors and student
aviators within the Naval Air Training Command.
2. This publication shall be used as an explanatory aid to the T-6B IFR Flight Planning
Curriculum. It will be the authority for the execution of all flight procedures and maneuvers
therein contained.
3. Recommendations for changes shall be submitted via the electronic Training Change Request
(TCR) form located on the Chief of Naval Air Training (CNATRA) website.
T. P. ATHERTON
By direction
WORKBOOK
T-6B
iii
LIST OF EFFECTIVE PAGES
iv
INTERIM CHANGE SUMMARY
CHANGE
REMARKS/PURPOSE
NUMBER
INTERIM
CHANGE REMARKS/PURPOSE ENTERED DATE
NUMBER BY
v
INTRODUCTION
Weather
It is intended to reinforce knowledge gained from the IN1300 block of primary flight training.
While a sound knowledge of this material is required for the IN1390 exam, it is the foundation
upon which every IFR flight is built.
vi
TABLE OF CONTENTS
CHAPTER FOUR – FLIP IFR ENROUTE LOW ALTITUDE CHARTS - U.S. (E LA) .. 4-1
400. INTRODUCTION ......................................................................................................... 4-1
401. FRONT AND BACK COVER ..................................................................................... 4-1
402. UNLETTERED PANEL DATA ................................................................................... 4-4
403. LEGEND ....................................................................................................................... 4-5
404. MARGIN DATA......................................................................................................... 4-11
405. CHAPTER FOUR REVIEW QUESTIONS ............................................................... 4-12
vii
CHAPTER FIVE – FLIP IFR ENROUTE HIGH ALTITUDE CHARTS - U.S. (E HA) .. 5-1
500. INTRODUCTION ......................................................................................................... 5-1
501. FRONT AND BACK COVER ..................................................................................... 5-1
502. UNLETTERED PANEL DATA ................................................................................... 5-3
503. LEGEND ....................................................................................................................... 5-4
504. MARGIN DATA........................................................................................................... 5-9
505. CHAPTER FIVE REVIEW QUESTIONS: ................................................................ 5-11
viii
CHAPTER TEN – FLIP TERMINAL HIGH ALTITUDE (T HA).................................... 10-1
1000. INTRODUCTION ................................................................................................... 10-1
1001. FRONT AND BACK COVER ................................................................................ 10-1
1002. TERMINAL HIGH ALTITUDE BOOK DIFFERENCES ..................................... 10-2
ix
CHAPTER FOURTEEN – FLIGHT PLANS ....................................................................... 14-1
1400. INTRODUCTION ................................................................................................... 14-1
1401. DD FORM 1801 (DoD FLIGHT PLAN) ................................................................ 14-1
1402. DD FORM 1801-C (STOPOVER FLIGHT PLAN) .............................................. 14-29
1403. FAA FORM 7233-4 (INTERNATIONAL FLIGHT PLAN) ................................ 14-31
1404. CHAPTER FOURTEEN REVIEW QUESTIONS ............................................... 14-33
x
TABLE OF FIGURES
Figure 4-1 IFR Enroute Low Altitude – U.S. (Front Cover) ............................................ 4-2
Figure 4-2 IFR Enroute Low Altitude – U.S. (Back Cover) ............................................. 4-3
Figure 4-3 Low Chart Military Training Route (MTR) Data .......................................... 4-4
Figure 4-4 Low Chart Military Operations Area (MOA) Data ....................................... 4-4
Figure 4-5 Low Chart Special Use Airspace (SUA) Data ................................................. 4-5
Figure 4-6 Low Chart Airport Locations ........................................................................... 4-5
Figure 4-7 FAA Aeronautical Chart User’s Guide............................................................ 4-6
Figure 4-8 Low Chart Airports Legend ............................................................................. 4-6
Figure 4-9 Low Chart NAVAIDs Legend........................................................................... 4-7
Figure 4-10 Low Chart Communication Boxes Legend...................................................... 4-7
Figure 4-11 Low Chart Route Data Legend ......................................................................... 4-8
Figure 4-12 Low Chart Fixes/ATC Reporting Legend ....................................................... 4-9
Figure 4-13 Low Chart Example of Groupings Legend ..................................................... 4-9
Figure 4-14 Low Chart Boundaries, Airspace, and SUA Legends .................................. 4-10
Figure 4-15 Low Chart MTR, Cruising Altitudes, and Miscellaneous Legends ............ 4-11
Figure 4-16 Low Chart Margin Data .................................................................................. 4-11
Figure 4-17 Sample IFR Enroute Low Altitude Chart Segment ..................................... 4-14
Figure 5-1 IFR Enroute High Altitude – U.S. (Front Cover) ........................................... 5-2
Figure 5-2 IFR Enroute High Altitude – U.S. (Back Cover) ............................................ 5-3
Figure 5-3 High Altitude Special Use Airspace Data ........................................................ 5-4
Figure 5-4 High Chart Airports Legend............................................................................. 5-5
Figure 5-5 High Chart NAVAIDS Legend ......................................................................... 5-5
Figure 5-6 VOR/DME/TACAN Standard Service Volumes ............................................ 5-6
Figure 5-7 High Chart Communications Boxes Legend ................................................... 5-6
Figure 5-8 High Chart Air Traffic Services and Airspace Information Legend ............ 5-7
Figure 5-9 High Chart Miscellaneous Legend ................................................................... 5-8
Figure 5-10 High Chart Example of Groupings Legend..................................................... 5-8
Figure 5-11 High Chart Morse Code Legend ...................................................................... 5-8
Figure 5-12 High Chart Cruising Altitudes Legend ............................................................ 5-9
Figure 5-13 High Chart Margin Data (All Sides) ................................................................ 5-9
xi
Figure 5-14 High Chart Margin Data (Bottom) ................................................................ 5-10
Figure 5-15 Sample High Altitude Chart ........................................................................... 5-12
Figure 9-1 FLIP Terminal Low Altitude (Front Cover) ................................................... 9-2
Figure 9-2 FLIP TCN (Front Cover) .................................................................................. 9-3
Figure 9-3 FLIP Terminal Low Altitude (Back Cover) .................................................... 9-4
Figure 9-4a FLIP Terminal Low Altitude General Information ....................................... 9-5
Figure 9-4b FLIP Terminal Low Altitude General Information (cont.) ........................... 9-6
Figure 9-5 FLIP Terminal Low Altitude Index ................................................................. 9-7
Figure 9-6a FLIP Terminal Low Altitude Planview Legend.............................................. 9-8
Figure 9-6b FLIP Terminal Low Altitude Planview Legend (cont.) .................................. 9-9
Figure 9-7 FLIP Terminal Low Altitude Profile Legend ................................................ 9-10
Figure 9-8a FLIP Terminal Low Altitude Landing Minima Legend .............................. 9-11
Figure 9-8b FLIP Terminal Low Altitude Landing Minima Legend (cont.) .................. 9-12
Figure 9-8c FLIP Terminal Low Altitude Landing Minima Legend (cont.) .................. 9-13
Figure 9-8d FLIP Terminal Low Altitude Landing Minima Legend (cont.) .................. 9-14
Figure 9-9 FLIP Low Altitude METAR Conversion Chart ........................................... 9-15
Figure 9-10 FLIP Terminal Low Altitude Airport Diagram/Sketch Legend ................. 9-16
Figure 9-11a FLIP Terminal Low Altitude STAR/SID Legend ......................................... 9-17
Figure 9-11b FLIP Terminal Low Altitude STAR/SID Legend (cont.) ............................. 9-18
Figure 9-12 INOP Components or Visual Aids Table ....................................................... 9-19
Figure 9-13 IFR Takeoff Minimums and (Obstacle) Departure Procedures.................. 9-21
Figure 9-14 Radar Instrument Approach Minimums....................................................... 9-23
Figure 9-15 IFR Alternate Minimums ................................................................................ 9-25
Figure 9-16 Land and Hold Short Operations (LAHSO) ................................................. 9-26
Figure 9-17 Hot Spots ........................................................................................................... 9-27
Figure 9-18 Basic IAP Sections............................................................................................ 9-28
Figure 9-19 IAP Top and Bottom Margins ........................................................................ 9-30
Figure 9-20 IAP Pilot Briefing Information ....................................................................... 9-31
xii
Figure 9-21 IAP Planview .................................................................................................... 9-33
Figure 9-22 IAP Profile View .............................................................................................. 9-34
Figure 9-23a IAP Landing Minimums.................................................................................. 9-39
Figure 9-23b IAP Landing Minimums (cont.)...................................................................... 9-39
Figure 9-24 IAP Airport Sketch .......................................................................................... 9-41
Figure 9-25 IAP Airport Sketch with Timing Table ......................................................... 9-42
Figure 9-26 SID ..................................................................................................................... 9-43
Figure 9-27 Graphic ODP .................................................................................................... 9-44
Figure 9-28 Airport Diagram .............................................................................................. 9-46
Figure 9-29 Climb/Descent Table ........................................................................................ 9-47
Figure 9-30 IAP for Review Questions ............................................................................... 9-48
Figure 10-1 FLIP Terminal High Altitude (Front Cover) ................................................ 10-1
Figure 10-2 FLIP Terminal High Altitude (Back Cover) ................................................. 10-2
Figure 10-3 High Altitude Only Procedure ........................................................................ 10-3
Figure 10-4 High/Low Altitude Procedure ......................................................................... 10-4
xiii
Figure 13-21 KMSY ILS or LOC RWY 2 .......................................................................... 13-31
Figure 13-22 KHSA VOR-A ................................................................................................ 13-33
Figure 13-23 KHSA IFR Alternate Airport Minimums ................................................... 13-34
Figure 13-24 Flight Planning Matrix ORIG/DEST/ALT1/ALT2 .................................... 13-34
Figure 13-25 KHUM VOR/DME RWY 30......................................................................... 13-35
Figure 13-26 KHUM IFR Alternate Airport Minimums .................................................. 13-36
Figure 13-27 Planning/Flight Log Matrixes ORIG/DEST/Viable ALT .......................... 13-37
Figure 13-28 Flight Log Elevation/Frequency Entries ...................................................... 13-38
Figure 13-29 Flight Log Climb/Cruise Winds/Temps ....................................................... 13-39
Figure 13-30 Time, Fuel, and Distance to Climb Table..................................................... 13-40
Figure 13-31 Flight Log Raw Climb Data .......................................................................... 13-41
Figure 13-32 CR-3 Climb TAS ............................................................................................ 13-41
Figure 13-33 CR-3 Climb Fuel Flow ................................................................................... 13-42
Figure 13-34 Flight Log Climb TAS/Fuel Flow ................................................................. 13-42
Figure 13-35 PCL Long Range Cruise Table..................................................................... 13-43
Figure 13-36 Flight Log Cruise TAS/Fuel Flow ................................................................ 13-44
Figure 13-37 Flight Log STTO ............................................................................................ 13-44
Figure 13-38 KHBG NAVAID Data ................................................................................... 13-46
Figure 13-39 Flight Log Completed Through Step 7 ........................................................ 13-47
Figure 13-40 CR-3 Plot Climb Winds ................................................................................. 13-48
Figure 13-41 KNBG Airport Diagram................................................................................ 13-49
Figure 13-42 CR-3 Climb Groundspeed Calculation ........................................................ 13-50
Figure 13-43 CR-3 Cruise Groundspeed ............................................................................ 13-51
Figure 13-44 Flight Log Groundspeeds .............................................................................. 13-52
Figure 13-45 CR-3 Climb Time Leg 1 ................................................................................ 13-53
Figure 13-46 CR-3 Climb Distance Leg 2 ........................................................................... 13-54
Figure 13-47 CR-3 Cruise Time Leg 2 ................................................................................ 13-55
Figure 13-48 Flight Log ETE entries .................................................................................. 13-56
Figure 13-49 Climb Fuel Computation ............................................................................... 13-58
Figure 13-50 Leg 2 Cruise Fuel Computation.................................................................... 13-58
Figure 13-51 Flight Log Leg Fuel Step 10 Complete ......................................................... 13-59
Figure 13-52 Flight Log EFR Step 11 Complete ................................................................ 13-61
Figure 13-53 CR-3 Fuel Remaining (Hrs + Min) at Destination ...................................... 13-62
Figure 13-54 Flight Log Fuel Remaining Step 12 Complete ............................................ 13-63
Figure 13-55 Flight Log Time to Alternate Step 13 Complete ......................................... 13-65
Figure 13-56 Flight Log Fuel Plan ...................................................................................... 13-66
Figure 13-57 NATOPS PCL Max Endurance Cruise ....................................................... 13-68
Figure 13-58 Flight Log Fuel Plan (Completed) ................................................................ 13-69
xiv
Figure 14-9 DD 1801 Item 16 Dest Airport / Total EET / ALTN Airport(s) ................ 14-14
Figure 14-10 DD 1801 Item 18 Other Information ............................................................ 14-21
Figure 14-11 Flight Log ........................................................................................................ 14-22
Figure 14-12 DD 1801 Item 19 FUEL ................................................................................. 14-23
Figure 14-13 DD 1801 Item 19 POB.................................................................................... 14-23
Figure 14-14 DD 1801 Item 19 RDO ................................................................................... 14-23
Figure 14-15 DD 1801 Item 19 Type of Equipment ........................................................... 14-23
Figure 14-16 DD 1801 Item 19 Life Jackets ....................................................................... 14-24
Figure 14-17 DD 1801 Item 19 Radio Frequency .............................................................. 14-24
Figure 14-18 DD 1801 Item 19 Dinghies ............................................................................. 14-24
Figure 14-19 DD 1801 Item 19 Other Equipment RMK ................................................... 14-25
Figure 14-20 DD 1801 Bottom Section Remarks ............................................................... 14-25
Figure 14-21 DD 1801 Bottom Section Crew List.............................................................. 14-25
Figure 14-22 DD 1801 Bottom Section Acft Serial Number & Type Of Acft In Flight . 14-26
Figure 14-23 DD 1801 Bottom Section Aircraft Home Station or Organization ............ 14-26
Figure 14-24 DD 1801 Bottom Section Name Of Pilot In Command-Instrument Rating. 14-26
Figure 14-25 DD 1801 Bottom Section Approving Authority .......................................... 14-27
Figure 14-26 DD 1801 Enroute Delay: (For Holding) ...................................................... 14-27
Figure 14-27 DD 1801 Terminal Delay: (For Practice IAP) ............................................ 14-28
Figure 14-28 DD 1801 Completed Example ....................................................................... 14-28
Figure 14-29 DD 1801-C Stopover Flight Plan .................................................................. 14-30
Figure 14-30 FAA Form 7233-4 International Flight Plan ............................................... 14-32
xv
THIS PAGE INTENTIONALLY LEFT BLANK
xvi
CHAPTER ONE
FLIP GENERAL PLANNING (GP)
100. INTRODUCTION
General Planning (GP) is published every 32 weeks with Planning Change Notices (PCNs)
issued at the 16-week mid-point of the GP book cycle, and Urgent Change Notices (UCNs)
issued as required. Effective dates are listed on the front cover. (See Figure 1-1)
This publication contains general information on all Flight Information Publications (FLIPs),
terms, explanation of the divisions of the United States Airspace, Flight Plans and Codes,
common worldwide procedures, ICAO (International Civil Aviation Organization) Procedures,
Operations and Firings over the High Seas and aviation codes. Currently this information is
divided into 11 Chapters.
This index lists the sections and chapters of the FLIP GENERAL PLANNING document in
which information may be found. It also lists other primary publications to which reference may
be made.
This chapter provides a complete list of terms and definitions published in the FAA
Pilot/Controller Glossary, plus some selected ICAO and Military terms. As a professional
aviator and to avoid confusion during communications with Controllers, these terms should be
known and employed.
This chapter describes the DoD FLIP program, individual FLIP products and related
publications.
This chapter contains detailed block by block instructions for completing the military flight plan
(DD Form 1801).
1. DD Form 1801 (DoD FLIGHT PLAN) is primarily used for all flights departing
installations having a Military Base Operations.
2. FAA Form 7233-4 (INTERNATIONAL FLIGHT PLAN) may be used lieu of DD Form
1801 when departing US installations not having a military airfield management/base operations
facility.
3. Type of Aircraft
The aircraft designation for the T-6B is listed under Beech Aircraft Company (USA). The
aircraft model is combined with the T-6A Texan II. The Aircraft Designation for both aircraft is
TEX2* (the asterisk denotes single-piloted military turbojet or aircraft to receive the same
procedural handling as a single piloted military turbojet aircraft). Do not use the asterisk on the
DD 1801 as the form will accept only 4 characters. (See Figure 1-2)
Fixed-Wing Aircraft
* Denotes single-piloted military turbojet aircraft or aircraft to receive the same procedural
handling as a single-piloted military turbojet aircraft.
1. This chapter outlines standard Pilot Procedures while operating under both Federal
Aviation Administration (FAA) and International Civil Aviation Organization (ICAO) control.
3. Those items requiring a ready reference while in-flight will be found in the IFR Enroute
Supplement or the Flight Information handbook.
4. The chapter is divided into sections all of which are applicable to your primary training.
a. GENERAL INFORMATION
b. AIRSPACE STRUCTURE
e. MAXIMUM AIRSPEEDS
f. RVSM RULES
j. CLEARANCE INFORMATION
Although ICAO rules and procedures are binding upon International Civil Aviation only;
Military Aircraft are expected to avoid conflicting with National regulations. While knowledge
of this information will not be required in primary training it will be a factor for many fleet
operations.
This chapter draws upon United States Government recognized international law and DoD policy
to provide information relevant to military flight operations in international airspace. While
knowledge of this information will not be required in primary training it will be a factor for
many fleet operations.
This chapter contains information regarding overall management of the FLIP program.
Refer to the GP when answering the following questions. (Look it up even if you know the
answer)
6. What VIP code would you use if a VADM was onboard, and he wanted full honors
accorded him? _______________.
7. Operations below 10,000 feet MSL at an indicated airspeed in excess of _______ KIAS, are
authorized for military aircraft only under certain conditions (defined in the GP).
8. When landing at U.S. Military bases, the pilot should verbally confirm the flight plan has
been closed with Tower or Base OPS personnel. (TRUE/FALSE)
9. Pilots should file an IFR flight plan at least _______ minutes (1 hour in some areas) prior
to ETD (Estimated Time of Departure).
10. At airports where a Control Tower is in operation, ATC IFR clearances normally are
relayed to pilots of departing aircraft by the Tower's “__________” position. At many busy
airports, by the Control Tower’s “____________________” position, if one has been established.
11. When given taxi instructions, pilots will acknowledge by all read-back______________
and _____________________instructions.
12. When a flight has been cleared to a fix short of a filed destination, additional clearance to
proceed beyond or instructions to hold at such fix will be issued at least ______minutes before
the aircraft is estimated to reach the fix.
13. The use of a Standard Instrument Departures (SID) by Navy pilots is mandatory if they are
available. (TRUE/FALSE)
16. Without specific exceptions, the maximum holding airspeed at 10, 000 feet MSL is
“__________” KIAS.
19. During holding, in the event of two-way communications failure, comply with procedures
in the FLIP ________________________________.
200. INTRODUCTION
Area Planning documents contain planning and procedure information for specific geographical
regions. (See Figure 2-1) The number following the AP designation denotes the region covered
in that publication. The regions are divided as follows:
Our focus will be on North and South America. The information for this region is divided into
three publications:
1. AP/1 – Area Planning: Published every 24 weeks and contains aeronautical data for North
and South America and supplements the data in General Planning (GP) and select data in the
Enroute Supplements (E-S) and Flight Information Handbook (FIH). Chapter 3 contains
information on the United States and will be the focus of our discussion. (See Figure 2-2)
2. AP/1A – Area Planning Special Use Airspace: Published every 8 weeks and contains all
Prohibited, Restricted, Warning, Danger, and Alert Areas listed by country. Military Operations
and known Parachute Jumping Areas are also listed. (See Figure 2-3)
3. AP/1B – Area Planning Military Training Routes: Published every 8 weeks and contains
information relative to Military Training Routes.
e. Effective dates and Planning Change Notice (PCN) dates are listed on the front
covers of each publication. (See Figure 2-4)
National Procedures
Flight Planning
Flight Hazards
Enroute
Terminal
Additional Information
a. Dimensional Units: Listed here are the units of measure used in the country such as
distances, time, visibility, weights, and altimeter settings.
b. Altimeter Setting Procedures: How altimeters are managed in the national airspace.
c. Vertical Separation: Rules for altitudes based on direction of travel (Semi-circular rules
in the US).
2. Visual Flight Rules: Standard except as prescribed by Federal Aviation Regulations (FAR).
Reduced Vertical Separation Minimum (RVSM)-rules that govern operations between FL290 and
410 are covered. The T-6B has No RVSM equipment and operations in this area require specific
coordination.
4. Flight Planning
a. Quota Flow Control - Explains the concepts and procedures used for balancing ATC
system demand with ATC system capacity.
c. United States Controlled Airspace - This section covers the different classifications of
airspace (class A, B, C, D, and E). It defines dimensions within which ATC service
is provides to IFR and VFR flights in accordance with the airspace classification.
The various divisions offer different types of ATC service and have specific
operating procedures and list minimum equipment required to operate in that
airspace. This section is divided into the following topics:
i. Class A Airspace
iii. Jet Route System - “J” Routes in airspace from 18,000’ MSL to FL450
inclusive.
v. VOR and L/MF AIRWAYS - “V” Routes that use VOR NAVAIDS from
1200’ AGL up to but not including 18,000’ MSL (L/MF airways are predicated
solely on L/MF NAVAIDS are depicted in brown).
x. Class G Airspace
xii. FAA Airspaces - additional information on the FAA airspace structure listed by
Class.
xiv. Restricted Area Procedures-rules regarding ATC IFR routing and clearances
around restricted areas.
6. Route and Area Restrictions: This section defines route pair restrictions and flight planning
requirements required under the National Route Program (NRP). This system is expanding and
already affects many routes, airports, Department of Energy (DOE) Nuclear Facilities, U.S.
Wildlife Refuges, Parks, and Forest Service Areas.
7. Flight Hazards: This section contains procedures for reporting Laser Illumination of
Aircraft and a list of general hazards broken down by each state.
8. Enroute: Preferred IFR Routes-Information for current U.S. Preferred Routes is available
at FAA website: http://www.fly.faa.gov/rmt/nfdc_preferred_routes_database.jsp. Checking this
site prior to filing could prevent unnecessary delays or changes to your flight plan.
10. Terminal: Contains Nosie Abatement Procedures for certain airports listed by each
affected state.
11. Additional Information: This section provides an alphabetical listing of VOR Receiver
Checkpoints. These facilities are available for operational checks of airborne VOR equipment.
This publication contains information on three categories of airspace; Special Use Airspace,
Parachute Jumping Areas and Military Operations Areas (MOAs)
P - Prohibited Area. Flights in this area are prohibited except by special permission.
R - Restricted Area. Flights are prohibited during published periods of use unless
permission is obtained from controlling authority.
W - Warning Area. Flights are not restricted but avoidance is advised during time of
use.
D - Danger Area. Flights are not restricted but avoidance is advised during time of
use.
A - Alert Area. Flights are not restricted. An area where there is concentrated
student training or other unusual area activity of operator significance
Number: The ICAO Location Identifier for the country, Airspace prefix, and
Airspace number. (Countries under FAA jurisdiction do not use ICAO Location
Identifiers). Examples: Restricted Area 2919A in Valparaiso, FL is listed as number
“R2919A.” The Pensacola North MOA is numbered as “MOA US01866”
Area Name
Effective Altitude
Effective Times
Weather
Under this information the boundaries of the airspace is defined with latitude/longitude along
with any other information deemed pertinent.
Information concerning this type of airspace is listed by country. The United States is further
divide by State.
The FAA established MOAs in which certain military flight training may be conducted on a
scheduled basis. MOAs are charted so non-participating aircraft may be aware of these
operations.
General procedures are provided for scheduling and coordination along with general flight
procedures. Specific scheduling information for each MOA is provided in table format.
This publication provides textual and graphic descriptions and operating instructions for all
military training routes. It is divided into six chapters:
General Guidance
Avoidance Locations
Refer to the AP publications when answering the following questions. (Look it up even if you
know the answer)
2. Class A airspace over the 48 contiguous states exists from _____________ to and including
__________.
3. Operations in Class A airspace must be conducted under IFR and ATC clearance must be
received prior to entering the airspace. (TRUE or FALSE)
5. Jet routes are identified by the letter ___ followed by the airway number. They are
predicated solely on ______ or _________ NAVAIDS (except in Alaska). They are established
in airspace from ___________ to __________________.
6. RNAV routes are depicted in ________ (color) on aeronautical charts and are identified by
the letter _____ or _____ followed by the airway number.
7. Q-routes are available for RNAV equipped aircraft between ____________ and
_____________ they are depicted on Enroute ______ Altitude Charts.
8. T-routes are available for RNAV equipped aircraft between ____________ and
_____________ they are depicted on Enroute ______ Altitude Charts.
9. Victor airways are identified by the letter “V” followed by the airway number. They are
depicted in _________ (color) on aeronautical charts.
10. Class B airspace generally from the surface to ____________ surrounding the nation’s
busiest airports in terms of IFR operations or passenger enplanements.
12. There are 32 areas designated as Class B airspace. In Florida they are located in
__________, _____________________, and _____________________.
13. The Class C Airspace has a basic design with minor site-specific variations. The design
consists of two concentric circles both centered on the primary airport. The inner circle has a
radius of ___ NM and the outer circle has a radius of ___ NM.
16. Class D Airspace generally is that airspace from the surface to __________ AGL
surrounding those airports with ____________________________________________.
18. From the surface to 18,000’ MSL the current reported altimeter setting of a station along
the route and within ______ NM of the aircraft shall be used.
19. At and above __________ feet MSL the standard QNE altimeter setting __________ will
be used at all times during flight. When using the standard altimeter setting, all reference to
altitudes shall be made in Flight Levels.
20. Pilots shall read back all altimeter settings received from Approach agencies.
(TRUE/FALSE)
21. Key West NAS (KNQX, FL requires all aircraft other than base-assigned aircraft or
scheduled detachment aircraft to obtain a ________________. The commercial phone number
for this purpose is _______________. This may be scheduled ______________ prior to arrival,
but no further in advance.
22. In Texas, what Flight Hazard is noted for the area around the McDonald Observatory?
______________________________________________________________________
300. INTRODUCTION
The IFR Enroute Supplement is used extensively during flight planning and is an essential
“In-Flight” reference publication. Don’t leave home without it! The effective dates are listed on
the cover page (See Figure 3-1). While much of the information concerning airports and
facilities is readily available in this document, NOTAMs and the AP/1 should be consulted
during planning for the latest changes or supplementary information that may be available.
The first pages have general information about the publication along with a handy table showing
the ICAO INTERNATIONAL PHONETIC ALPHABET/MORSE CODE.
After General Information, the publication is divided into three major sections:
The inside back cover of the publication has FAA formats to be used for position reports, change
of flight plan and filing flight plans in flight. (See Figure 3-3)
The outside of the back cover has ICAO formats for position reports and change of flight plan.
It is essential that you be well versed in the use of this publication, especially Sections A
and B.
This section is the “codebook” used to decipher all the information contained in Section B.
1. Sample Entry: A sample entry is provided for each type of Airport or facility used in the
Supplement. Each group of information in the sample is identified by a number.
2. Legend: This area starts with some general information concerning overall content. It then
explains in detail the contents of the directory. The descriptions are keyed to the boxed numbers
on the sample listing.
3. Abbreviations: All abbreviations and or acronyms used in the IFR Supplement are listed
here alphabetically. Additional abbreviations and or acronyms used for other FLIP products and
NOTAMs can be found in the Flight Information Handbook (FIH).
This section contains an alphabetical listing of all Airports, Air Traffic Control Centers, Flight
Information Centers, Communications Stations, and Radio Aids to Navigation.
For an airport to be included in this publication it must meet certain requirements defined in the
legend.
Listings of airports in the directory are by the airport name. In some instances, the city name and
airport name differ or the name of the city is not the first part of the airport name. This reference
provides an alphabetical listing by city for those airports.
2. Airport/Facilities Directory-US
3. Airport/Facilities Directory-Canada
4. Airport/Facilities Directory-Mexico
1. ADIZ Procedures
2. Cruising Altitudes
Refer to the IFR Supplement when answering the following questions. (Look it up even if you
know the answer)
2. All airports in the U.S. that have a published DoD Instrument Approach Procedure and/or
ASR Radar approach minima will be included in the Airport/Facility directory of the IFR
Supplement. (TRUE/FALSE)
3. NOTAM information for DoD aircrews is obtained using the DoD Aeronautical
Information Portal (DAIP) which interfaces with the Federal NOTAM System (FNS). The web
page is _________________________________________________.
6. Is there a permit that covers FRENANDINA BEACH MUNI airport for use by Transient
Military Aircraft? (YES/NO)
7. In the U.S., daylight saving time is in effect from 0200 local time on
______________________ to 0200 local time the _____________________________.
8. What is the time conversion required for STURGIS MUNI, KY during daylight saving
time? ___________.
9. What are the hours of operation that DONALDSONVILLE MUNI is attended during
periods of daylight-saving time? __________________________________.
10. The forecasted winds for arrival at EASTERWOOD FLD are 090/15. This would favor
runway _____ which is ________ feet long and ________ feet wide.
12. What is required for transient A/C to park on the military ramp at YUMA MCAS?
_________. How do you obtain that? ______________________________________.
13. Can I get the airport weather for ZANESVILLE MUNI by phone? (YES/NO) If so, what
type of weather is available and what is the number. _______________________.
14. What is the frequency for Pilot to Metro Service (PMSV) at NEW ORLEANS NAS JRB?
______________.
15. How far from GOLIAD NOLF is the THREE RIVERS VORTAC? ________________.
17. The VHF frequency for the PICAYUNE NAVAID is ___________. Its three-letter
identifier is _________.
19. The primary VHF frequency for HOUSTON CENTER when near Hattiesburg is _____ for
high altitudes and ________ for low altitudes. These are discrete frequencies.
400. INTRODUCTION
These charts portray the airway system for the 48 contiguous States and related data required for
IFR Operations at altitudes below 18,000 feet Mean Sea Level (MSL).
Enroute Charts are needed for both flight planning and enroute operations. Understanding the
material presented on these charts is crucial for successful navigation in the National Airspace
System (NAS).
Currently there are 36 variable scale charts printed on 18 sheets. Two charts for each sheet. One
chart is on the front sheet and another on the back. The panels for each chart are assigned a letter
(A, B, C…) to aid in locating charted information. The charts are labeled L-1 through L-36.
3. Legend
4. Margin Data
A graphic on the front cover depicts the geographical area covered by each chart in the Low
Altitude system. Heavy BOLD lines are used to denote the area covered on the specific charts to
which this graphic is attached.
Cities appearing in black indicate major traffic hubs for which Area Charts are provided. Area
charts are scaled to provide greater detail. An alphabetical list (by city) of available Area charts
and the chart number they appear on is noted in a table on the front cover.
Cities in green are to assist you in orientation and selection of the appropriate Low Altitude
Chart.
The effective date and chart number for the odd sheet is listed at the top (just below the fold).
This aids organization when filing the charts in an upright orientation. Note that the chart
numbers begin with “L” this is to differentiate them from High Altitude Charts which begin with
“H.”
Effective dates/times are the key feature of this cover. Always ensure that you have current
charts for the period covering your planned flight.
The charts numbers are shown along with arrows directing which side of the sheet each chart is
on. Below the chart number, the scale for the “lettered” panel sections for each sheet is listed.
Altitudes permitted for use are clearly noted. This is the same for all IFR Enroute Low Altitude-
U.S. charts. (For use up to but not including 18,000’ MSL)
A special box labeled “ATTENTION” contains important amplifying information. Here noted is
a detailed description of “Off Route Obstruction Clearance Altitudes (OROCA). This crucial
information is needed when flying off published airways.
This data is located on the unlettered panel sections at the sides of each sheet. This data includes
information pertaining to the following items:
The “NUMBER” defines the type of MTR and its number ID. The altitude range denotes the
routes altitude coverage.
This table contains information on; the name and number of the MOA, its effective altitudes, the
time it is used (in UTC), the controlling agency, and lists the panel(s) that the MOA appears on.
This table contains its own legend to aid in understanding information it contains. Basically, it
provides; type of airspace and specific number, effective altitudes of use, times of operation,
controlling agency and panel(s) that the SUA appears on.
This table list all charted airports by name, airport identifier (three letter ID), and the panel(s) the
airport appears on.
403. LEGEND
This material is crucial for interpreting chart symbology and information. Simply stated:
“Know it!” The time you spend here is a professional investment that cannot be overstated!
The General Planning (GP) Chapter Two (TERMS) has definitions for some of the items used in
the legend.
The FAA publishes the “Aeronautical Chart User’s Guide.” It is a must for your professional
library. It provides an expanded view with detailed information on each type of information
covered on the charts. It is available on-line at www.faa.gov under Air Traffic/Flight
Information/Aeronautical Information Services/Digital Products/Chart Users Guide.
The top half of the IFR Enroute Low Altitude Legend is divided into three groups.
AIRPORTS:
NAVAIDS:
COMMUNICATION BOXES:
The bottom half of the Legend, starting at the fold in the chart, is labeled:
This half of the Legend is divided into the following nine groups of information:
ROUTE DATA:
EXAMPLE OF GROUPING:
BOUNDARIES
AIRSPACE INFORMATION
Figure 4-15 Low Chart MTR, Cruising Altitudes, and Miscellaneous Legends
Along the margins at the top and bottom of each “lettered” panel of the chart, the following
information can be found:
5. The next intersection found along the airway on the adjoining chart
6. The identifier and frequency for NAVAID defining the airway on the adjoining chart
Refer to the GP, IFR Enroute Low Altitude - U.S. Legends and Figure 4-17 as required to answer
the following questions.
5. Between ROMMY and ELSIE on V198, what does “*1300” refer to and what does it
ensure? ________________________________________________________________
6. Below V198 just west of Jeremiah Denton airport (4R9) is the number; 29
, what is it and
what does it ensure? ________________________________________________
7. On V198 at ROMMY, what is “MRA 4000” and what does it indicate? _______________
8. What does a flag symbol with and X in the middle ( ) indicate? ________________
9. Traveling southwest from BROOKLEY VORTAC on V198, how far is it to the next
compulsory Fix and /or NAVAID? ________________________________
10. Traveling southwest from BROOKLEY VORTAC on V198, at what DME from BFM is
the NAVAID changeover point? ________________________________
11. The Air Route Traffic Control Center for this area is _____________. What Ultra High
Frequency should be used to contact them? ________________________________
12. Can ATC contact you over the BROOKLEY VOR frequency of 112.8? ___________
13. In the KEESLER communication box, (111.8) indicates what? How would this be used in
the T-6B? ___________________________________________
14. What is the name of the Flight Service Station serving the area around BFM? __________
15. What frequencies are available at many Flight Service Stations even when not annotated on
the chart? ____________________________________________
16. When flying IFR on V198 from BROOKLEY towards ROMMY you would expect what
type of cruising altitude? ____________________________________________
500. INTRODUCTION
These charts portray the airway system and related data required for IFR Operations at altitudes
at and above 18,000 feet Mean Sea Level (MSL).
Enroute Charts are needed for both flight planning and enroute operations. Understanding the
material presented on these charts is crucial for successful navigation in the National Airspace
System (NAS).
Currently there are twelve charts printed on six sheets. Two charts for each sheet. One chart is
on the front sheet and another on the back. The panels for each chart are assigned a letter (A, B,
C…) to aid in locating charted information. The charts are labeled H-1 through H-12. Charts
H-1 through H-11 cover the 48 contiguous States, with chart H-12 duplicating data shown on
charts H-9, H-10 and H-11 for those who frequently plan flights north and south along the East
coast within the area of coverage.
3. Legend
4. Margin Data
A graphic on the front cover depicts the geographical area covered by each chart in the High
Altitude system. Heavy bold lines are used to denote the area covered on the specific charts to
which this graphic is attached.
Cities appearing in black are to assist you in orientation and selection of the appropriate High
Altitude Chart.
The effective date and the two chart numbers are listed at the top (just below the fold). This
aids organization when filing the charts in an upright orientation. Note that the chart numbers
begin with “H” to differentiate them from Low Altitude Charts which begin with “L.”
Effective dates/times are the key feature of this cover. Always ensure that you have current
charts for the period covering your planned flight.
The charts numbers are show along with arrows directing which side of the sheet each chart is
on. Below the chart number, the scale for the “lettered” panel sections for each sheet is listed.
The altitudes permitted for use is clearly noted. This is the same for all IFR Enroute High
Altitude- U.S. charts. (For use at and above 18,000’ MSL) Note the important reminder
“Consult NOTAMs for latest Information.”
This data is located on unlettered panel sections at the sides of one sheet. This data includes
information pertaining to the following items:
This table has its own legend for the data it contains. It provides the following information:
b. Effective altitudes
503. LEGEND
While very similar to the legend used for the Low Altitude Charts there are some variations
important to high altitude operations. Consult the FLIP GP and the FAA Aeronautical Chart
User’s Guide for specific definitions and symbol details. Note the differences from the Low
Altitude Charts. The legend is divided into the following basic sections:
AIRPORTS
NAVAIDS
COMMUNICATIONS BOXES
MISCELLANEOUS
EXAMPLE OF GROUPING
MORSE CODE
CRUISING ALTITUDES
Only airports that have hard surfaced runway(s) with a minimum of 5000 feet are shown. The
data available for each airport is limited to the city name, airport name and airport identifier.
ILS Localizer course are not depicted on the High Altitude Charts.
Similar to the low altitude chart legend. One difference is NAVAID Standard Service Volume
(SSV) Class Designators are annotated as Low Altitude (L) or Terminal (T) if other than High
Altitude.
Figure 5-6 shows the SSV details from the Aeronautical Information Manual (AIM). These are
referred to as Radio Class Codes in the IFR Enroute Supplement.
This section is divided into the same areas as the low chart. While much of the data presented is
the same there are differences specific to the high altitude structure. Noteworthy are the
designations used for the different types of airways.
Figure 5-8 High Chart Air Traffic Services and Airspace Information Legend
Note that the rules vary depending on the altitude being flown. While the T-6B is capable of
flights up to FL310, without RVSM equipment clearance above FL 280 depends on ATC
traffic/workload and requires prior coordination.
Along the margins (top, bottom and sides) of each chart the following information is found:
(See Figure 5-13)
The next intersection found along the airway on the adjoining chart
The identifier and frequency for NAVAID defining the airway on the adjoining chart
Along the bottom margin the following additional information is provided: (See Figure 5-14)
Consult other FLIP documents as required for terms, definitions, or explanations as required.
Refer to Figure 5-15 for the following questions:
4. Write out the Morse code for the NORHTBROOK NAVAID. __________,
______________, ______________.
5. What is the NAVAID changeover point on J35-101 between JOLIET and PONTIAC?
__________________________________________________________________
7. In addition to its Morse code identifier, what other information is broadcast on the
KOKOMO VORTAC? _________________________________
8. What does MAA-35000 indicate? (Located on J84 between the changeover point and
WORDY intersection) _________________________________
9. What does the box with 117 inside of it mean? (Located on J84 between the changeover
point and WORDY intersection) _________________________________
11. What is the green dotted line just west of the GIPPER VORTAC? ___________
12. FABIO intersection is located just east of the NORTHBROOK NAVAID. How is it
defined (fixed)? Is it a part of J584? _________________________________
14. Is an Instrument Approach procedure (IAP) and /or RADAR MINIMA published for
Grissom ARB? _________________________________
15. What is the Minimum Enroute Altitude (MEA) for J146 between JOLIET and GIPPER?
_______________________________________________________
16. Traveling east from JOLIET to GIPPER on J146, what is the new course after the
changeover point? ____________________________________________
17. Traveling from ROBERTS to NORTHBROOK on J19-71, due to forecasted winds aloft
you expect to fly a wind corrected heading of 355° to track along that airway. For this leg of
your flight, you should plan for what type of altitude between FL180 and FL280? ___________
18. IFR Enroute High Altitude charts are not to be used above FL280. (TRUE/FALSE)
600. INTRODUCTION
These charts portray the airway system and related data required for IFR operations in selected
terminal areas at altitudes below 18,000 feet Mean Sea Level. Currently fourteen variable scale
charts are printed on one sheet.
The Area Charts provide greater detail for congested areas around major airports. Chart layout
and symbology are the same as the IFR ENROUTE LOW ALTITUDE – U.S. charts. As such
they have no legends attached to them.
The front cover depicts effective date and cities at which Area Charts available.
The back cover list the effective dates and depicts which chart contains which cities. Because
Area Charts have no legend there is a statement directing the user to “Consult Enroute Charts for
Legend Information.”
700. INTRODUCTION
This handbook contains aeronautical information required by DoD aircrews in flight, but which
is not subject to frequent change. Due to the vast amount of material contained in this
publication, it is not practical to be memorized. However, familiarity and ready access to the
content is essential.
The front cover displays effective dates and a table of contents for the publication (a more
detailed table of contents precedes each individual section). (See Figure 7-1)
The inside front cover list any Special Notices concerning new flip features.
Page one contains general information concerning management of the FIH publication.
Page two is an alphabetical index of subjects. It lists which section a particular topic may be
found in.
The Back cover provides a ready reference for ICAO aircraft Interception procedures (the inside
back cover is for the FAA rules). For countries that have different rules they are covered in
section A. Hopefully you will be the one doing the intercepting.
Figure 7-3 FIH Section B: National and International Flight Data and Procedures
1. Information concerning lighting systems can be found in section ____ of the FIH.
2. If communications are lost during an IFR flight, aircraft equipped with a coded radar
beacon transponder should set ___________ in their transponder.
3. During two-way radio communications failure pilots can expect ATC to attempt contact
with them on ___________________________ and _________________________________.
5. The normal NAVAID spacing below 18,000 feet MSL is ______ NM.
6. The protected airspace along and airway when with 51 NM of the facility has a total width
of ____ NM, ______ NM each side of centerline.
7. In a climb, Altimeter Changeover Procedures require you to set ________ in the altimeter
upon reaching _____________ feet MSL.
8. In a radar environment, list the “Additional Reports” that should be made without a specific
ATC request.
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
10. The primary purpose for PILOT-TO-METRO SERVICE (PMSV), USN AND USMC is
for communicating various types of weather information to pilots. It is also used to;
_____________________________________ and ____________________________________.
11. PMSV at NAS Pensacola can be contacted on _____. Their radio call is ______________.
12. The FAA Weather Service is available 24 hours a day in person, by radio or phone. They
provide three types of preflight weather briefings. If using this service for flight planning the
night before your departure you should request a _______________ briefing. This brief is for
_______________________________.
13. A convective SIGMET would be issued by the NWS for a severe thunderstorm with winds
greater than or equal to____________ or hail at the surface greater than or equal to
____________.
14. Automated Surface Observation System (ASOS) is found at many airports in the U.S. It
provides minute-by-minute weather observations. It can be transmitted over a VHF radio
frequency or the voice portion of a local NAVAID. It is engineered to be receivable to a
maximum of ______ NM from the ASOS site and a maximum altitude of ___________ AGL.
15. The Aviation Routine Weather Report (METAR) intensity symbol of (+) means
_________ and the precipitation designation of “GR” means ______________.
17. According to the Frequency Pairing Plan, the TACAN DME channel 119x at NAS
Pensacola is paired with a VOR frequency of ________. This is useful information when using
the DME hold function in the T-6B!
27. The ICAO NOTAM code contains a total of 5 letters. The first letter is always a Q. The
second and third letters identify _____________. The fourth and fifth letters denote
_____________________. A code of QICAC indicates ___________________________.
800. INTRODUCTION
A STAR is an ATC coded IFR arrival route designed to expedite air traffic control arrival
procedures and facilitate transition between the enroute phase of flight and terminal instrument
approach operations.
Each STAR procedure is presented as a separate chart and may serve a single airport or more
than one airport in a given geographical location. All STARs for the 48 contiguous States are
published in one volume. (See Figure 8-1)
These procedures may be required when your destination or alternate is located at or near high
traffic terminals. Always check to see if there is a STAR associated with your
destination/alternate. Expect to use them or be prepared for delays and/or re-routing.
1. Selecting A Star
An “Index of Instrument Procedure Charts” is located in the front of the STAR publication. (See
Figure 8-2) This index is an alphabetical list by city/state and airport name. Under each airport
the STAR names and page numbers can be found. The STAR charts are published in
alphabetical order by the STAR name.
2. Filing a Star
The top and bottom margins of each chart contains the plain language name and number of the
STAR, the city and state it is designed for, and in parenthesis an ATC code for that chart. For
example, in Figure 8-3a the plain language name for the star covering the New Orleans,
Louisiana area is the RHYTHM FOUR ARRIVAL. The ATC code for the chart is
RYTHM.RYTHM4.
Each chart may have multiple Arrival/Transition Routes. These transitions also have individual
plain language names followed by their specific ATC codes in parenthesis.
To continue our previous example, if you plan to enter the STAR from the EATON VORTAC
(See Figure 8-3a), you should look for transition information.
This transition information may be on the first page of the chart or may be found on following
pages. On page two of our example (See Figure 8-3b), the plain language name for the transition
we would need is the EATON TRANSITION. The ATC code of LBY.RYTHM4 for that
transition is what should be entered in the route of flight on our flight plan.
Selecting the appropriate ATC code for filing will avoid confusion and unnecessary delays.
Legends for symbology on the STAR Charts are located in the front of the publication after the
Index of Instrument Procedure Charts. (See Figures 8-4a and 8-4b). These charts have features
used on both the IFR Enroute Low/High Charts and the FLIP Terminal Low/High Approach
Plates.
STAR procedures may have mandatory speeds and/or crossing altitudes published. Other
STARs may have planning information depicted to inform pilots what clearances or restrictions
to “expect.” “Expect” altitudes/speeds are not considered STAR procedures crossing restrictions
unless verbally issued by ATC.
Published speed restrictions are independent of altitude restrictions and are mandatory unless
modified by ATC. Pilots should plan to cross waypoints with a published speed restriction, at
the published speed, and should not exceed this speed past the associated waypoint unless
authorized by ATC or a published note to do so.
Pilots cleared for STAR procedures are expected to laterally navigate as depicted, comply with
published speed restrictions, and must maintain last assigned altitude unless otherwise
instructed by ATC. If the clearance for the STAR contains the phraseology “descend via” the
pilot is authorized and expected to descend so as to comply with all published/issued restrictions.
900. INTRODUCTION
The FLIP Terminal Low Altitude publications for the United States currently consist of twenty-
two bound booklets. They contain Instrument Approach Procedures (IAPs), Airport Diagrams,
Standard Instrument Departures (SIDs) and Radar Instrument Approach Minimums along with
other useful information. These volumes contain all DoD (Low Altitude) terminal instrument
procedures and selected civil terminal instrument procedures requested by the military for the 48
contiguous States.
1. The Front Cover (See Figure 9-1) shows the publication volume number, a graphic
portrayal of the states contained, and the effective dates. Note it covers an eight-week cycle.
Midway through the cycle (at the four-week point) revisions are published in a separate TCN
(Terminal Change Notice). (See Figure 9-2)
If your flight will occur on or after the TCN effective date, you must check the TCN. All
airports which have revised, added, or deleted terminal procedures (IAPs, Radar Minima, Airport
Diagrams, or SIDs) are listed alphabetically in the TCN table of contents. If the airport of
intended landing/departure is not listed in the table of contents of the TCN, then the airport
information in the basic volume has not changed. TCNs cover all revisions to both the FLIP
Terminal HIGH and LOW Publications.
2. The Back Cover (See Figure 9-3) of the FLIP Terminal Low publication depicts how states
are divided into volume numbers.
This section provides general information not specifically covered in other portions of the
publication (see Figure 9-4a and 9-4b). Noteworthy are the Pilot Controlled airport lighting
systems information and the list of common abbreviations used throughout the publication.
The table of contents and an “Index of Instrument Procedure Charts” is located in the front of the
FLIP Terminal Low Altitude publication (see Figure 9-5). This index is an alphabetical list by
city/state and airport name. Under each airport the procedure names and page numbers can be
found.
Procedures are published alphabetically by the city name. This index is helpful when the airport
name and airport city are different.
904. LEGENDS
Legends and tables of information needed for interpreting each section of the instrument
procedures can be found in the front of the publication immediately following the Index. Much
of this information is also available in the Aeronautical Chart User’s Guide.
This legend contains symbols and information found in the overhead (360°) view of an IAP.
2. Profile
This legend contains symbols and information found in the profile (side) view of an IAP.
(See Figure 9-7)
This legend contains three pages of symbols and information needed to interpret critical
information in the final approach, and landing areas. (See Figures 9-8a, 9-8b, 9-8c, and 9-8d)
Figure 9-8b FLIP Terminal Low Altitude Landing Minima Legend (cont.)
Figure 9-8c FLIP Terminal Low Altitude Landing Minima Legend (cont.)
Figure 9-8d FLIP Terminal Low Altitude Landing Minima Legend (cont.)
This chart provides conversions needed to interpret ceiling, runway visibility, and prevailing
visibility information. (See Figure 9-9)
This legend provides airport information and symbols for runways, approach lighting systems,
obstacles, surface reference features, and other data contained in the small Airport Sketch located
on the IAP and the larger Airport Diagram when they are available. (See Figure 9-10)
6. STAR/SID
This legend covers symbology found in both the FLIP STAR publication and the Standard
Instrument Departure (SID) procedures located in this publication. (See Figures 9-11a and
9-11b)
Landing minimums published on instrument approach procedures charts are based upon full
operation of all components and visual aids associated with the particular instrument approach
chart being used.
If ground instrument components or visual aids are Inoperative this table list the required
adjustment needed for the visibility minimums. This table may be amended by notes on the
approach chart.
Always check NOTAMs and listen to ATIS for information concerning inoperative components
or visual aids at your destination or alternate.
This section is located in the front of the publication prior to the Radar Instrument Approach
Minimums and IAPs. (See Figure 9-13)
Departure Procedures (DPs) specifically designed for obstacle avoidance are referred to as
Obstacle Departure Procedures (ODPs) and are textually described in this section or published
separately as a graphic procedure.
ODPs published as graphic procedures are found in the IAP section. Graphic ODPs can be
recognized by the term “(OBSTACLE)” included in the procedure title.
Airports that have ODPs will display the TROUBLE “T” symbol on the IAP as a reminder to
check this section for details.
This section is found in the front portion of the publication following the Takeoff Minimums
Section. Airports that have published radar minimums are listed alphabetically.
There are three types of radar approaches: Airport Surveillance Radar (ASR), Precision
Approach Radar (PAR) and the Precision Approach Radar With/Out Glideslope (PAR W/O GS).
Circling and Sidestep minimums for these approaches may also be listed.
The PAR is Precision Approach because both course and glideslope information is provided
by the controller.
The ASR and PAR W/O GS are non-precision approaches because only course information is
provided by the controller.
Communication frequencies commonly used by the controlling agency are listed at the top after
the airport name.
PAR approach data also includes glideslope angle (GS), Threshold Crossing Height (TCH), and
Runway Point of Intercept (RPI).
General information concerning approaches for the airfield is listed following the minimums
data.
The FAA considers standard alternate weather minimums of 800-2 for non-precision approaches
and 600-2 for precision approaches. Airports listed in this section require other than standard
minimums or have alternate minimums with restrictions.
Ceiling and Visibility minimums are not applicable to USA/USN/USAF. CNAF M-3710.7 sets
required alternate weather minimums for Navy/Marine Corps operations. However, restrictions
other than ceiling and visibility still apply. Pilots must review the IFR Alternate Minimums
notes to determine alternate airfield suitability.
Example: The symbol on the IAP indicates alternate minimums are not authorized
due to an unmonitored facility or absence of weather reporting service. This includes CNAF
minimums!
These operations include landing and holding short of an intersection runway, an intersection
taxiway, or other predetermined points on the runway other than a runway or taxiway.
This is an alphabetical list of city/airports that have LAHSO requirements. The information
provided includes the landing runway, the hold short point, and the measured distance available
for landing.
The Aeronautical Information Manual (AIM) contains specific details regarding this type of
operation. LAHSO points are also depicted on the corresponding Airport Diagram in the IAP
section.
Hot Spots are areas on the aerodrome movement area with a history or potential risk of collision
or runway incursion. Heightened attention by pilots is necessary for safe operation.
Listed alphabetically by city/airport name, the information for each airport includes the hot spot
number, and a description of the area concerned.
The Hot Spot numbers and a circle around the affected area are also depicted on the
corresponding Airport Diagram in the IAP section.
These are a series of predetermined maneuvers for the orderly transfer of an aircraft under
instrument flight conditions from the beginning of the initial approach to a landing, or to a point
from which a landing may be made visually or the missed approach procedure is initiated.
IAPs contained in the FLIP DoD Terminal Low and High publications are issued by the FAA,
USN, USAF, and USA.
All information required to execute these maneuvers can be found on the appropriate IAPs
(commonly referred to as “Approach Plates”). Each IAP can be broken down into basic areas of
information. (See Figure 9-18)
Individual IAPs are identified on the top and bottom margins of the page by their procedure
name (based on the NAVAIDs required for the final approach), runway served, and airport
location. The identifier for the airport is also listed immediately after the airport name.
NOTE
Crosshatching displayed along the upper left half of the top border
and the lower right half of the bottom border denote that the
procedure appears in both the Terminal High and Terminal Low
publications.
Straight–in IAPs are identified by the navigational system providing the final approach guidance
and the runway to which the approach is aligned (e.g., VOR RWY 13).
Circling only approaches are identified by the navigational system providing final approach
guidance and a letter from the beginning of the alphabet (e.g., VOR A). Multiple circling
procedure using the same navigational system it will use follow on letters from the beginning of
the alphabet (e.g., VOR A, VOR B, VOR C, etc.)
Multiple approaches to the same runway (not circling) using the same navigational guidance will
be annotated with an alphabetical suffix beginning at the end of the alphabet and working
backwards for subsequent procedures (e.g., ILS Z RWY 28, ILS Y RWY 28, etc.).
More than one navigational system separated by a slash indicates that more than one type of
equipment must be used to execute the final approach (e.g., VOR/DME RWY 31).
More than one navigational system separated by the word “or” indicates either type of equipment
may be used to execute the final approach (e.g., VOR or GPS RWY 15).
In some cases, other types of navigation systems including radar may be required to execute
other portions of the approach or to navigate to the IAF. When radar or other equipment is
required for procedure entry from the enroute environment, a note will be charted in the
planview of the approach procedure chart (e.g., Radar Required). When radar or other
equipment is required on portions of the procedure outside the final approach segment, including
the missed approach, a note will be charted in the notes box of the pilot briefing portion of the
approach chart for IAPs issued by the FAA
NOTE
Some military (e.g., U.S. Air Force and U.S. Navy) IAPs have
these “additional equipment required” notes charted only in the
planview of the approach procedure and do not conform to the
same application standards used by the FAA.
Notes are not charted when VOR is required outside the final approach segment. Pilots should
ensure that the aircraft is equipped with the required NAVAID(s) in order to execute the
approach, including the missed approach.
Top Margin
Bottom Margin
Figure 9-19 IAP Top and Bottom Margins
This section aids the pilot as they set up and prepare for the approach. This information
includes:
c. Runway Length
e. Airport Elevation
h. Missed Approach Procedures: (This is the complete list of instructions unlike the
abbreviated information/symbols found in the profile view.)
This section provides aircrew with a 360° “Birds eye” view for the area around the approach and
airport environment. While an excellent tool for overall situational awareness, it also provides
key elements necessary for navigation and safe operations.
A thorough understanding of the planview symbology (See Figures 9-6a and 9-6b) along with
knowledge of the terms and definitions they represent is crucial. The GP and AIM are key
sources for explanation of many terms. Another important source document is the NATOPS
Instrument Flight Manual (NIFM).
The following is a sample of some general terms used to describe symbology in this section of an
IAP:
b. Initial Approach Fix (IAF). The fix(s) depicted on the Instrument Approach
Procedure charts that identify the beginning of the initial approach segments(s).
c. Initial Approach. The segments between the Initial Approach Fix and the
intermediate fix or point where the aircraft is established on the intermediate or final
approach course.
d. Intermediate Fix (IF). The fix that identifies the beginning of the intermediate
approach segment. (Not depicted for every approach)
e. Intermediate Approach. The segment between the intermediate fix or point and the
Final Approach Fix (FAF).
f. Final Approach Fix (FAF). The fix from which the final approach (IFR) to the airport
is executed and which identifies the beginning of the final approach segment.
g. Final Approach Segment. The segment between the Final Approach Fix or point and
the runway, airport or missed approach point.
j. Minimum Safe Altitude (MSA). Altitudes depicted on approach charts which provide
at least 1,000 feet of obstacle clearance for emergency use within a specified distance
from the navigation facility upon which the procedure is predicated. These altitudes
will be identified as Minimum Sector Altitude (MSA) or Emergency Safe Altitude
and are established as follows:
k. Terminal Arrival Area (TAA). The objective of the TAA is to provide a seamless
transition from the enroute structure to the terminal environment for arriving aircraft
equipped with FMS and/or GPS navigational equipment. The TAA provides the pilot
and controller with a very efficient method for routing traffic into the terminal
environment with little required air traffic control interface. Once cleared for the
approach the pilot may use the published altitudes in their sector as they provide
standard obstacle clearance compatible with the instrument procedure associated with
it. When the TAA is published, it replaces the MSA for that instrument procedure.
Where IAPs that have a solid circle displayed, all distances within the circle are to the scale
depicted on the circle. A circle with dashed lines indicates an area that is NOT to scale. These
“dashed” circles are used to aid orientation from Enroute and/or Feeder facilities to the Initial
Approach Fix(s) (IAFs).
This is a cross section view of the approach procedure. A thorough understanding of the profile
view symbology (See Figure 9-7) along with knowledge of the terms and definitions they
represent is crucial. The GP and AIM are key sources for explanation of many terms. Another
important source document is the NATOPS Instrument Flight Manual (NIFM).
The following is a sample of some general terms used to describe symbology in this section of an
IAP:
e. Visual Descent Point (VDP). A defined point on the final approach course of a non-
precision straight-in approach procedure from which normal descent from the
Minimum Descent Altitude to the runway touchdown point may be commenced,
provided the approach threshold of that runway, or approach lights, or other markings
identifiable with the approach end of that runway are clearly visible to the pilot.
Where a VDP is published, pilots should not descend below the Minimum Decent Altitude
(MDA) prior to reaching the VDP and acquiring the necessary visual reference. Pilots not
equipped to receive the VDP should fly the approach as though no VDP had been provided.
The minimums in this section are depicted by type of approach being executed and aircraft
approach category. Minimums are expressed in terms of altitude and visibility. The two key sets
of minimums are:
Weather minimums. Ceilings, Prevailing Visibility (PV) and/or Runway Visual Range (RVR)
constitute weather minima. These are used for flight planning purposes and are the requirements
for commencing approaches for single-piloted aircraft. Minimum ceiling and visibility required
for the procedure are separated by a - or a / and enclosed in parenthesis. The - is used when
depicting PV, and the / is used to denote RVR values. If RVR is available, it takes precedence
over PV as a requirement for commencing an approach.
In addition to these published minimums, CNAF M-3710.7 provides the following guidance
concerning absolute minimums:
5.3.5.3 Approach Criteria for Single-Piloted Aircraft
An instrument approach shall not be commenced if the reported weather is below published
minimums for the type approach being conducted. When a turbojet enroute descent is to be
executed, the approach is considered to commence when the aircraft descends below the highest
initial penetration altitude established in high altitude instrument approach procedures for the
destination airport. Once an approach has been commenced, pilots may, at their discretion,
continue the approach to the approved published landing minimums as shown in the appropriate
FLIP for the type approach being conducted. Absolute minimums for a single-piloted
fixed-wing aircraft executing an approach are 200-foot ceiling/height above touchdown and
visibility of 1/2 statute-mile/2,400 feet RVR.
Altitude minimums. The minimum altitude a pilot is allowed to descend on the final segment
of a precision approach is referred to as the Decision Altitude (DA). The minimum altitude for
a non-precision approach is expressed as a Minimum Decent Altitude (MDA). The visibility
required for the final approach are published following the MDA/DA separated by a / or a – but
are not enclosed in parenthesis. The CNAF restrictions noted above apply to altitude minimums
as well.
A thorough understanding of the profile view symbology (See Figures 9-8a, 9-8b, and 9-8c)
along with knowledge of the terms and definitions they represent is crucial. The GP and AIM
are key sources for explanation of many terms. Another important source document is the
NATOPS Instrument Flight Manual (NIFM).
The following are samples of general terms used to describe symbology in this section of an IAP:
NOTES
2. For precision approaches, the T-6B may only use the S-ILS
minima in this section. The T-6B is also capable of Precision
Radar Approaches; however, PAR Minima are listed in the Radar
Instrument Approach Minimums section in the front of the
publication.
(d). CIRCLING
NOTES
c. Approach Category. A grouping of aircraft based on a speed of 1.3 times the stall
speed in the landing configuration at maximum gross landing weight.
ii. Category B - Speeds 91 knots or more but less than 121 knots
iii. Category C - Speeds 121 knots or more but less than 141 knots
iv. Category D - Speeds 141 knots or more but less than 166 knots
NOTES
e. Ceiling. The height above the earth’s surface of the lowest layer of clouds or
obscuring phenomena that is reported as “broken”, “overcast”, or “obscuration”.
Ceiling heights are expressed in AGL.
f. Decision Altitude (DA). A specified altitude referenced to Mean Sea Level (MSL)
in the precision approach at which a missed approach must be initiated if the required
visual reference to continue the approach has not been established.
NOTE
g. Decision Height (DH). A specified altitude referenced Above Ground Level (AGL)
in the precision approach at which a missed approach must be initiated if the required
visual reference to continue the approach has not been established.
NOTES
h. Height Above Airport (HAA). The height of the minimum descent altitude (MDA)
above the published airport elevation. This is published in conjunction with circling
minimums. It is expressed in feet Above Ground Level (AGL).
i. Height Above Touchdown (HAT). The height of the Decision Height (DH), Decision
Altitude (DA), or Minimum Descent Altitude (MDA) above the highest runway
elevation in the Touchdown Zone (first 3000 feet of the runway). HAT is published
on instrument approach charts when utilized to determine straight-in minimums. It is
expressed in feet Above Ground Level (AGL).
j. Minimum Descent Altitude (MDA). The lowest altitude, expressed in feet above
mean sea level (MSL), to which a descent is authorized on final approach or during a
circle-to-land maneuver in execution of a standard instrument approach procedure
where no electronic glideslope is provided.
l. Runway Visibility Value (RVV). The visibility determined for a particular runway
by a transmissometer. A meter provides a continuous indication of the visibility
(reported in statute miles or fractions of statue mile) for the runway. RVV is used in
lieu of prevailing visibility in determining minimums for a particular runway.
The Airport Sketch is found in the bottom of the Procedure Chart. It may appear on the left or
right side of the chart beside the profile view and landing minimums. It depicts the field layout
and includes the following information where applicable:
a. Airport elevation
d. Approach visual aids available: Approach lighting type, VASI, PAPI, OLS (See the
FIH for more information on Approach Lighting.)
e. Taxi surfaces
f. Tower/Beacon location
h. Missed Approach Timing Table (located below the airport sketch where applicable)
A thorough understanding of the Airport Sketch symbology (See Figure 9-10) along with
knowledge of the terms and definitions they represent is crucial. The GP and AIM are key
sources for explanation of many terms. Another important source document is the NATOPS
Instrument Flight Manual (NIFM).
The following is a sample of some general terms used to describe symbology in this section of an
IAP:
a. Approach Light System (ALS). An airport lighting facility which provides visual
guidance to landing aircraft by radiating light beams in a directional pattern by which
the pilot aligns the aircraft with the extended centerline of the runway on his final
approach to landing.
b. U.S. Navy Optical Landing System (OLS). A visual slope indicating system. It
consists of a horizontal row of green lights with a yellow “ball” in the center. When
the yellow ball is aligned with the green lights the aircraft is on slope, when the
yellow ball is above the green lights the aircraft is above slope, if the ball is below the
green lights the aircraft is below glideslope and the ball color will change from
yellow to red if excessively low. The OLS is depicted on the Airport Sketch and
Airport diagram because its height of approximately 7 feet and proximity to the edge
of the runway may create an obstruction for some types of aircraft.
d. Runway End Identifier Lights (REIL). Two synchronized white flashing lights one
on each side of the runway threshold, which provide rapid and positive indication of
the approach end of a particular runway.
e. Touchdown Zone (TDZ). The first 3,000 feet of runway beginning at the threshold.
The area used for determination of Touchdown Zone Elevation in the development of
straight-in landing minimums for instrument approaches.
f. Touchdown Zone Elevation (TDZE). The highest elevation in the first 3,000 feet of
the usable landing surface. The usable surface begins at the threshold/displaced
threshold.
g. Visual Approach Slope Indicator (VASI). This visual glideslope system provides
vertical visual approach slope guidance to aircraft during approach to landing by
radiating a directional pattern of high intensity red and white focused light beams
which indicate to the pilot that he is “on path” if he sees red/white, “above path” if he
sees white/white and “below path” if he sees red/red. Some airports have a three-bar
VASI which provide two visual paths to the same runway.
A SID provides transition from the terminal area to the appropriate enroute structure during the
departure phase of flight. When available, they are depicted graphically following the IAP
section for each airport in both the FLIP Terminal Low/High Altitude publications.
Graphic depictions of Obstacle Departure Procedures (ODPs) are also found in this section
where available. Graphic ODPs are noted by (OBSTACLE) in the title. (See Figure 9-27)
They reduce the frequency and complexities of the communications required to issue
and receive such instructions.
They provide safe tracks/altitudes in the event of lost communications during the
departure phase.
1. Filing a SID
The top and bottom margins of each chart contains the plain language name and number of the
SID, the city and state it is designed for, and in parenthesis an ATC code for that chart. For
example, in Figure 9-26 the plain language name for the SID covering the Cairns AAF in Fort
Rucker, Alabama is the POPER-ONE DEPARTURE. The ATC code for the SID is
POPER1.POPER.
Each chart may have multiple Transition Routes. These transitions also have individual plain
language names followed by their specific ATC codes in parenthesis. For example, in
Figure 9-26, if you intend to use the MARIANNA TRANSITION you would file POPER1.MAI
instead of “POPER1.POPER.”
Selecting the appropriate ATC code for filing will avoid confusion and unnecessary delays.
Legends for symbology for the SIDs are located in the front of the publication after the Index of
Instrument Procedure Charts. (See Figures 9-11a and 9-11b). These charts have features used
on both the IFR Enroute Low/High Charts and the FLIP Terminal Low/High Approach Plates.
SIDs may have mandatory speeds and/or crossing altitudes published. Published speed
restrictions are independent of altitude restrictions and are mandatory unless modified by ATC.
Pilots should plan to cross waypoints with a published speed restriction, at the published speed,
and should not exceed this speed past the associated waypoint unless authorized by ATC or a
published note to do so.
Pilots cleared for STAR procedures are expected to laterally navigate as depicted, comply with
published speed restrictions, and must maintain last assigned altitude unless otherwise
instructed by ATC. If the clearance for the SID contains the phraseology “climb via” the pilot is
authorized and expected to climb so as to comply with all published/issued restrictions.
Airport Diagrams are provided for some airports. Where available they will be the last chart in
the IAP section for a given airport. The legends used for this chart are the same ones used in
conjunction with the Airport Sketch on the IAPs.
Airport Diagrams are basically an expanded version of the Airport Sketch. The Airport Diagram
provides greater detail especially with regard to ground operations. They are vital when
operating at unfamiliar airports especially those with complex taxiway systems.
When contacting Ground Control, this diagram will aid the pilot in reporting their position on the
airfield. It is also needed to understand and navigate the taxi instructions received from the
controller.
Hot Spots (HS) and Land and Hold Short Operations (LAHSO) are also depicted on this diagram
and aid in arrivals as well as departures. (See Figures 9-16, 9-17 for HS and LAHSO
legends/information)
The inside back cover of every STAR, Terminal Low/High publication has an Instrument
Takeoff or Approach Procedure Charts Rate of Climb/Descent Table. This table is used for
planning and executing climbs or descents under known or approximate ground speed
conditions.
The following questions refer to Figure 9-30. Consult appropriate FLIP publications as needed
for additional references.
2. What type of navigation equipment is required to navigate the final approach segment of
this approach? _________________________________________________________
4. What is the frequency of the NAVAID required for the Final Approach Segment?
____________________
9. In the event of a missed approach, where will you go to hold if waiting for additional
clearance? __________________________________________________
10. You would expect to be cleared for this approach by ______________ on a VHF frequency
of ______________.
11. List the published Initial Approach Fixes for this approach. _______________________
12. What NAVAID is needed to navigate between UYSEF and DIXVU? _________
13. What is the course and distance from IGB to HANOP? _________________________
14. The Minimum Safe Altitude is _______ MSL within ______ NM of _________________.
15. What is the altitude restriction between the FAF and JAKVU? ____________________
16. The glideslope for the ILS is ____° and the Threshold Crossing Height will be ______ feet
AGL if on glideslope.
18. The T-6B Decision Altitude for the ILS approach is _________. Is this an MSL or AGL
altitude? ___________
19. The weather required for the ILS approach is ______ feet and _______ sm.
20. The aircraft Height Above Touchdown when at the Decision Altitude for this approach is
________ feet. Is that MSL or AGL? ________
21. The distance between the Final Approach Fix and the Missed Approach Point is __ NM.
22. This field has a SSALR type approach lighting system. (TRUE/FALSE)
23. Runway End Identifier Lights are available for runway 18. (TRUE/FALSE)
24. If you are required to maintain a minimum climb gradient of 600 feet per nautical mile, you
need to maintain a minimum VSI of _____ for a T-6B normal climb speed.
(Refer to Figure 9-29)
1000. INTRODUCTION
The FLIP Terminal High Altitude publications for the United States currently consist of three
bound booklets. They are tiled by the geographic area they cover, e.g., Northwest, Southwest,
and East. The format and information provided in the Terminal High Altitude books are nearly
identical to those found in the FLIP Terminal Low Altitude books. This chapter will focus on
the few differences.
The front and Back covers have crosshatching around all the borders to differentiate them from
the Terminal Low Altitude booklets.
The Front cover depicts the geographical area of coverage, the effective dates and when the TCN
will be effective. Recall that the TCN (Terminal Change Notice) contains changes for both the
Terminal High and Low publications.
The Back cover depicts the 48 contiguous states broken into the three geographical areas. This
depiction aids in determining which booklet(s) will be needed for your mission.
Crosshatching Displayed across the entire top and bottom boarders of the Approach or Departure
Charts denotes High Altitude Procedures (these procedures will not be found in the Terminal
Low publications). (See Figure 10-3)
Like the Low Altitude booklets, where crosshatching is displayed along the upper left half of the
top border and the lower right half of the bottom border of the Approach or Departure chart the
procedure appears in both the Terminal High and Terminal Low publications. (See Figure 10-4)
Instrument Approach Procedure names in the top and bottom margins begin with HI- followed
by the standard approach naming criterion e.g., HI-ILS or LOC/DME RWY 23.
The Legends have additional symbology and information particular to high altitude procedures.
There are only three Aircraft Approach Categories for landing minima: C, D, and E.
NOTE
IFR Alternate Minimums that are non-standard and Alternate Minimums Not Authorized,
along with the associated tabulation data are not included in the High Altitude procedures.
1100. INTRODUCTION
1. NOTAM information for DoD aircrews is obtained using the DAIP which interfaces with
the Federal NOTAM System (FNS). The DAIP webpage is listed in the Enroute Supplement
Legend section under NOTAMS. Currently the address is:
https://www.daip.jcs.mil/daip/mobile/index.
2. NOTAMs should be checked for all applicable areas concerning your proposed flight. This
includes but is not limited to (depending on the flight):
a. Departure Airport
b. Destination Airport
c. Alternate Airport
d. Route of flight
3. If the Airport identifier is not covered by the NOTAM system you will get an error
message “Location not covered by the US NOTAM System.” In this case NOTAMs may be
available via phone from the FSS or possibly call the airport directly.
When access to DAIP is not possible, FAA Flight Service Stations (FSS) may be used to obtain a
NOTAM briefing. This can be conducted in person at airports with a FSS on site (rare) or may
be obtained by phone (1-800-WX-BRIEF).
1. NOTAM (D)
– Information includes such data as taxiway closures, personnel and equipment near or
crossing runways, and airport lighting aids that do not affect instrument approach
criteria, such as VASI.
2. FDC NOTAMs
c. They are also used to advertise Temporary Flight Restrictions (TFRs) caused by such
things as natural disasters or large scale public events that may generate a congestion
of air traffic over a site.
3. Pointer NOTAMs
b. This type of NOTAM will assist users in cross-referencing important information that
may not be found under an airport or NAVAID identifier.
c. Keywords in pointer NOTAMs must match the keywords in the NOTAM that is
being pointed out.
4. SAA NOTAMs
– These NOTAMS are issued when Special Activity Airspace will be active outside the
published schedule times and when required by the published schedule.
5. Military NOTAMs
– NOTAMs pertaining to U.S. Air force, Army, Marine, and Navy navigational
aids/airports that are part of the National Airspace System (NAS).
Domestic Notices and International Notices are not provided during a standard FSS briefing
unless specifically requested by the pilot since the FSS specialist has no way of knowing whether
the pilot has already checked the Federal NOTAM System (FNS) NOTAM Search System
External links prior to calling. Airway NOTAMs, procedural NOTAMs, and NOTAMs that are
general in nature and not tied to a specific airport/facility (for example, flight advisories and
restrictions, open duration special security instructions, and special flight rules areas) are briefed
solely by pilot request. Remember to ask for these Notices if you have not already reviewed this
information, and to request all pertinent NOTAMs specific to your flight. FAA Domestic and
International Notices can be obtained via the FAA Web page
https://www.faa.gov/air_traffic/publications/notices. There is also a link from the DAIP
webpage.
3. NOTAM information for DoD operations should be obtained via the Department of
Defense Aeronautical Information Portal (DAIP). The URL for the webpage can be found in the
__________________________ FLIP and is currently __________________________.
4. NOTAMs should be checked for all applicable areas concerning your proposed flight. This
includes but is not limited to (depending on the flight):
a. ___________________________________________________
b. ___________________________________________________
c. ___________________________________________________
d. ___________________________________________________
e. ___________________________________________________
f. ___________________________________________________
5. If access to the DAIP is not possible, FAA Flight Service Stations (FSS) may be used to
obtain a NOTAM briefing. This can be conducted in person at airports with a FSS on site (rare)
or may be obtained by phone at ____________________________.
6. FDC NOTAMS are ______________ in nature. They contain such things as amendments
to ____________________________________ and other aeronautical charts. They are also
used to advertise __________________________ caused by such things as natural disasters or
large scale public events that may generate a congestion of air traffic over a site.
7. When receiving a NOTAM brief from the FSS, they will not include
_________________________________ unless specifically requested by the pilot.
8. A link to obtain FAA Domestic and International Notices can be found on the
_____________ webpage.
1200. INTRODUCTION
CNAF: Naval aviators shall be thoroughly familiar with weather conditions for the area in
which flight is contemplated. Many sources of weather information, both governmental and
commercial, are readily available to assist pilots in flight planning and operations. For flights
where any portion of the intended route is forecast to be under IMC, naval aviators shall obtain a
flight route weather brief from a DoD-qualified forecaster or approved forecasting service.
NIFM: Pilots are responsible for reviewing and being familiar with weather conditions for the
area in which flight is contemplated. Before obtaining a flight clearance, a pilot must receive a
weather briefing where services are available; the briefing shall be conducted by a qualified
meteorological forecaster. These briefings may be conducted in person, or when available, via
weather-vision, telephone, or by autographic means. Additionally, a DD Form 175-1 (Flight
Weather Briefing) shall be completed for all flights in accordance with CNAF M-3710.7 series.
Due to the perishable nature of meteorological data, and in an effort to ensure aviators have
the most up-to-date information, all weather briefings will be assigned a briefing void time.
The briefing void time shall not exceed the “weather briefed” time by more than 3 hours, and
it shall never exceed the planned departure time by more than 30 minutes. This time may be
extended when, in the opinion of the meteorologist, conditions are such that a review of the
initial form and the deletion/addition of pertinent data is such that a formal re-briefing is not
required. When extending void times, the rule stated above applies with the exception that the
“weather re-briefed at” time is used as the base time.
CNAF: The primary method for requesting and obtaining flight route weather briefings ashore is
online through the Web-enabled Flight Weather Briefer (FWB) system
https://fwb.metoc.navy.mil (account and CAC access required) operated by DoD-qualified
meteorological forecasters at the Naval Aviation Forecast Center (NAFC), its satellite
components, or within the Marine Corps Weather Services. Alternate methods of delivery are
available upon request.
CNAF: If operating from locations without access to FWB, naval aviators may obtain route
weather forecast support from NAFC via 1-888-PILOTWX. Additionally, an approved flight
route weather briefing may be obtained via an FSS or through Air Force Weather and Marine
Corps Services, where available. (A listing of military weather/NOTAM briefing facilities can
be found in SECTION C of the FIH)
FSS Weather Briefings can be obtained by calling 1-800-WX-BRIEF. Flight Service Specialist
are qualified and certified by the National Weather Service (NWS) as Pilot Weather Briefers.
They are not authorized to make original forecast, but are authorized to translate and interpret
available forecast and reports directly into terms describing the weather conditions which you
can expect along your route of flight and at your destination.
WEATHER 12-1
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
1. Standard Briefing: This briefing includes Adverse Conditions, VFR Flight Not
recommended (if appropriate), Synopsis, Current Conditions, Enroute Forecast, Destination
Forecast, Winds Aloft, NOTAMS, ATC Delays. Additional items available at the pilots request
include; Special Use Airspace, Review of NTAP, Density Altitude, Air Traffic Services/Rules,
GPS RAIM Availability, and other assistance as required.
3. Outlook Briefing: You should request an Outlook Briefing whenever your proposed time
of departure is six or more hours from the time of the briefing. The briefer will provide
available forecast data applicable to the proposed flight. This type of briefing is provided for
planning purposes only. You should obtain a Standard or Abbreviated Briefing prior to
departure in order to obtain such items as adverse conditions, current conditions, updated
forecasts, winds aloft and NOTAMs, etc.
4. Inflight Briefing: You are encouraged to obtain your preflight briefing by telephone or in
person before departure. In those cases where you need to obtain a preflight briefing or an
update to a previous briefing by radio, you should contact the nearest FSS to obtain this
information. After communications have been established, advise the specialist of the type
briefing you require and provide appropriate background information. You will be provided
information as specified in the above paragraphs, depending on the type of briefing requested.
When neither FWB or FSS briefing services are available, commercial weather forecasting
services may be used providing they meet the following requirements:
Comply with all ICAO, FAA, FAR and Joint Aviation Requirement on
Commercial Air Transportation (JAROPS) requirements.
12-2 WEATHER
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK CHAPTER TWELVE
In addition, the final approving authority authorizing specific commercial flight forecasting
services rests with the TYCOM. Reporting custodians are not responsible to fund commercial
flight forecasting services.
Inflight Aviation Weather Advisories are forecasts to advise enroute aircraft of development of
potentially hazardous weather. Inflight aviation weather advisories in the conterminous U.S. are
issued by the Aviation Weather Center (AWC) in Kansas City, MO, as well as 20 Center
Weather Service Units (CWSU) associated with ARTCCs.
There are four types of inflight aviation weather advisories: The SIGMET, the Convective
SIGMET, the AIRMET (text or graphical product), and the Center Weather Advisory (CWA).
All of these advisories use the same location identifiers (Either VORs, airports, or well−known
geographic areas) to describe the hazardous weather areas.
The Severe Weather Watch Bulletins (WWs), (with associated Alert Messages) (AWW)
supplements these Inflight Aviation Weather Advisories.
A SIGMET advises of weather that is potentially hazardous to all aircraft. In the CONUS,
SIGMETs are issued when the following phenomena occur or are expected to occur:
b. Severe or extreme turbulence or clear air turbulence (CAT) not associated with
thunderstorms.
d. Volcanic ash.
Any convective SIGMET implies severe or greater turbulence, severe icing, and low−level wind
shear. A convective SIGMET may be issued for any convective situation that the forecaster feels
is hazardous to all categories of aircraft.
Convective SIGMETs are issued in the conterminous U.S. for any of the following:
ii. Hail at the surface greater than or equal to 3/4 inches in diameter.
iii. Tornadoes.
WEATHER 12-3
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
b. Embedded thunderstorms.
c. A line of thunderstorms.
3. AIRMETs (WA)
iii. AIRMET Zulu describes moderate icing and provides freezing level heights.
The Storm Prediction Center (SPC) in Norman, OK, issues Watch Notification Messages to
provide an area threat alert for forecast organized severe thunderstorms that may produce
tornadoes, large hail, and/or convective damaging winds within the CONUS.
SPC issues three types of watch notification messages: Aviation Watch Notification Messages,
Public Severe Thunderstorm Watch Notification Messages, and Public Tornado Watch
Notification Messages.
It is important to note the difference between a Severe Thunderstorm (or Tornado) Watch and a
Severe Thunderstorm (or Tornado) Warning. A watch means severe weather is possible during
the next few hours, while a warning means that severe weather has been observed, or is expected
within the hour. Only the SPC issues Severe Thunderstorm and Tornado Watches, while only
NWS Weather Forecasts Offices issue Severe Thunderstorm and Tornado Warnings.
The Aviation Watch Notification Message product is an approximation of the area of the Public
Severe Thunderstorm Watch or Public Tornado Watch. The area may be defined as a rectangle
or parallelogram using VOR navigational aids as coordinates.
12-4 WEATHER
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK CHAPTER TWELVE
The Aviation Watch Notification Message was formerly known as the Alert Severe Weather
Watch Bulletin (AWW). The NWS no longer uses that title or acronym for this product. The
NWS uses the acronym SAW for the Aviation Watch Notification Message, but retains AWW in
the product header for processing by weather data systems.
Public severe thunderstorm and tornado watch notification messages were formerly known as
the Severe Weather Watch Bulletins (WW). The NWS no longer uses that title or acronym for
this product but retains WW in the product header for processing by weather data systems.
CWAs are unscheduled inflight, flow control, air traffic, and air crew advisory. By nature of its
short lead time, the CWA is not a flight planning product. It is generally a now-cast for
conditions beginning within the next two hours. CWAs will be issued:
When an Inflight Advisory has not been issued but observed or expected weather
conditions meet SIGMET/AIRMET criteria based on current pilot reports and
reinforced by other sources of information about existing meteorological conditions.
CNAF: Except for operational necessity, emergencies, and flights involving all-weather
research projects or weather reconnaissance, pilots shall not file into or through areas for which
the SPC has issued a WW unless one of the following exceptions apply:
WEATHER 12-5
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
i. VFR filing is permitted if existing and forecast weather for the planned route
permits such flights.
ii. IFR flight may be permitted if aircraft radar is installed and operative, thus
permitting detection and avoidance of isolated thunderstorms.
iii. IFR flight is permissible in controlled airspace if VMC can be maintained, thus
enabling aircraft to detect and avoid isolated thunderstorms.
NOTES
CNAF: Operational Necessity. A mission associated with war or peacetime operations in which
the consequences of an action justify accepting the risk of loss of aircraft and crew.
CNATRAINST 3710.2: Flights shall not be filed into areas covered by Aviation Severe
Weather Watch Bulletins (WW), or Convective SIGMETs unless the exempting conditions
listed in CNAF M-3710.7 exist.
The following weather restrictions apply to both IFR pre-flight planning and IFR inflight
operations:
1. Takeoff Minimums
Standard instrument rating: CNAF requires that weather for departure allow for an emergency
return for the landing runway in use.
Non-Precision Approach (NPA): Published minimums for the available approach but not less
than 300-foot ceiling and 1-statute mile visibility.
Precision Approach: Published minimums for the available approach but not less than 200-foot
ceiling and 1/2-statute-mile visibility/2,400-foot runway visual range (RVR).
12-6 WEATHER
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK CHAPTER TWELVE
CNAF: For straight-in approaches, pilots shall use RVR, if available, to determine if visibility
meets the weather criteria for approaches, which are published in DoD FLIP Terminal Approach
Procedures. Prevailing visibility shall be used for circling approach criteria.
CNAF: Absolute minimums for a single-piloted fixed-wing aircraft executing an approach are
200-foot ceiling/height above touchdown and visibility of 1/2 statute-mile/2,400 feet RVR.
CNAF: Approach Criteria for Single-Piloted Aircraft: An instrument approach shall not be
commenced if the reported weather is below published minimums for the type approach being
conducted. When a turbojet enroute descent is to be executed, the approach is considered to
commence when the aircraft descends below the highest initial penetration altitude established in
high altitude instrument approach procedures for the destination airport. Once an approach has
been commenced, pilots may, at their discretion, continue the approach to the approved
published landing minimums as shown in the appropriate FLIP for the type approach being
conducted.
To ensure an adequate margin of safety the following table shall be used to determine
the weather requirements for selection of an alternate. See Figure 12-1.
CNATRAINST 3710.2: All fixed wing flights and any helicopter with a Student Naval
aviator in a crew position shall have sufficient fuel to proceed to a suitable alternate
regardless of destination weather.
DESTINATION WEATHER ALTERNATE WEATHER
ETA plus and minus 1 hour ETA plus and minus 1 hour
0 – 0 up to but not including Published minimums 3,000 – 3 or better
Published minimums up to but not including 3,000 – 3 NON-PRECISION PRECISION
(single-piloted absolute minimums 200 –1/2)
(single-piloted helicopter/tilt-rotor absolute minimums Published minimums Published minimums
200-1/4) plus 300-1 plus 200-1/2
WEATHER 12-7
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
b. The existing and forecast weather for the entire route of flight.
c. Destination and alternate forecasts for a period 1 hour before ETA until 1
hour after ETA.
5. CNATRAINST 3710.2
a. Flights shall not be filed into airfields with present or forecast snow or ice
covered runways.
CNAF: Flights shall be planned to circumvent areas of forecast atmospheric icing and
thunderstorm conditions whenever practicable.
AIM: A pilot can expect icing when flying in visible precipitation, such as rain or cloud droplets,
and the temperature is between +02 and −10 degrees Celsius. When icing is detected, a pilot
should do one of two things, particularly if the aircraft is not equipped with deicing equipment;
get out of the area of precipitation; or go to an altitude where the temperature is above freezing.
This “warmer” altitude may not always be a lower altitude. Proper preflight action includes
obtaining information on the freezing level and the above freezing levels in precipitation areas.
NATOPS: Sustained operation in icing conditions is prohibited. The aircraft has been approved
only for transit through a 5000-foot band of light rime ice.
AIM: RIME ICE - A rough, milky, opaque ice formed by the rapid freezing of super-cooled
drops/droplets after they strike the aircraft. The rapid freezing results in air being trapped giving
the ice its opaque appearance and making it porous and brittle. Rime ice typically accretes along
the stagnation line of an airfoil and is more regular in shape and conformal to the airfoil than
glaze ice. It is the ice shape, rather than the clarity or color of the ice, which is most likely to be
accurately assessed from the cockpit.
The DD-175-1 weather briefs are only valid for 3.0 hours past briefing/FWB delivery time or
ETD plus one-half hour. Briefings received more than 3.0 hours prior to takeoff will be void and
require re-briefing prior to departure.
12-8 WEATHER
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK CHAPTER TWELVE
Weather for preflight planning may be obtained from the FSS by requesting an “Outlook
Briefing” as previously discussed. However, another asset that may be used to obtain weather
data needed to prepare a Flight Log the night before is the Aviation Weather Center (AWC)
website http://www.aviationweather.gov (See Figure 12-2). This site provides access to the
Aviation Digital Data Service (ADDS). This site can provide all the data needed to complete
your preliminary planning/flight log.
ADDS; makes available to the aviation community text, digital and graphical forecasts, analyses,
and observations of aviation-related weather variables. ADDS; is a joint effort of NCAR
Research Applications Program (RAP), Global Systems Division (GSD) of NOAA's Earth
System Research Laboratory (ESRL), and the National Centers for Environmental Prediction
(NCEP) Aviation Weather Center (AWC).
The AWC Homepage "Standard Briefing" is intended to help pilots better visualize weather and
weather-related hazards. It is not intended as a substitute for a weather briefing obtained from
the FWB or a Flight Service Station (1-800-WXBRIEF). Currently, the information contained
here does not meet the FAA requirements for a route weather brief. Therefore, it's important
that pilots still obtain an official weather briefing prior to filing the flight plan.
WEATHER 12-9
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
12-10 WEATHER
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK CHAPTER TWELVE
METARs are taken manually by NWS, FAA, contractors, or supplemental observers. METAR
reports are also provided by Automated Weather Observing System (AWOS), Automated
Surface Observing System (ASOS), and Automated Weather Sensor System (AWSS).
TAFs are a concise statement of the expected meteorological conditions at an airport during a
specified period. TAFs use the same codes as METAR weather reports.
NOTE
Figures 12-3 and 12-4 provide a good review of TAF and METAR
codes, how they are presented, and the data they contain.
WEATHER 12-11
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
12-12 WEATHER
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK CHAPTER TWELVE
WEATHER 12-13
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
ARTCCs broadcast a Severe Weather Forecast Alert (AWW), Convective SIGMET, SIGMET,
AIRMET, Urgent Pilot Report or CWA alert once on all frequencies, except emergency, when
any part of the area described is within 150 miles of the airspace under their jurisdiction. These
broadcasts advise pilots of the availability of hazardous weather advisories and to contact the
nearest Flight Service facility for additional details.
Flight Service Specialist are qualified and certified as Pilot Weather Briefers by the FAA but are
not authorized to make original forecast, but are authorized to translate and interpret available
forecast and reports directly into terms describing the weather conditions which you can expect
along your route of flight and at your destination.
Inflight weather information is available from any FSS within radio range. Common frequencies
of 122.2 VHF and 255.4 UHF are available at many FSSs. Discrete frequencies for individual
stations are shown on the IFR Enroute Charts and can also be found in the FAA Chart Supplement
U.S. (Formerly called the “Airport/Facility Directory”).
Enroute advisories tailored to the phase of flight that begins after climb-out and ends with
descent to land are provided upon pilot request. Pilots are encouraged to provide a continuous
exchange of information on weather, winds, turbulence, flight visibility, icing, etc., between
pilots and inflight specialists. Pilots should report good weather as well as bad, and confirm
expected conditions as well as unexpected. Remember that weather conditions can change
rapidly and that a “go or no go” decision should be assessed at all phases of flight.
The primary purpose of PMSV (radio call “METRO”) is for communicating various types of
weather information to pilots. PMSV is also used to update the Flight Weather Briefing Form
(DD-175-1) and to receive pilot weather reports (PIREPS) of significant or hazardous weather
phenomena, which are entered into weather telecommunications networks.
PMSV for USN and USMC stations utilize the NAVMETOCCOM Sub-Regional Forecast
Center (SRFC) concept of operations in which forecasting has been centralized to support
outlying satellite detachments during off-peak hours, when a forecaster is not on duty.
Most NAVMETOCCOM and USMC stations are manned 24 hours with observers maintaining a
basic weather watch. Observers are authorized to provide basic weather information via PMSV,
such as providing the latest field conditions or nearby observation data, or reading a Terminal
Aerodrome Forecast (TAF) report. For any requests for forecast services, DD-175-1 updates, or
12-14 WEATHER
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK CHAPTER TWELVE
extensions, the observer acts as an intermediary between the pilot and SRFC forecaster. Some
delay will be experienced in these instances as the SRFC Forecaster receives and processes
information for the observer to pass along to the pilot over PMSV.
Locations, frequencies, and hours of operation can be found in the FIH Section “C.”
Arrival ATIS transmissions on a discrete VHF and/or UHF radio frequency are engineered
according to the individual facility requirements, which would normally be a protected service
volume of 20 NM to 60 NM from the ATIS site and a maximum altitude of 25,000 feet AGL.
Airport/Facility name
Visibility
Obstructions to vision
Present weather consisting of; sky condition, temperature, dew point, altimeter, a
density altitude advisory when appropriate and other pertinent remarks included in the
official weather observation
The ceiling/sky condition, visibility, and obstructions to vision may be omitted from the ATIS
broadcast if the ceiling is above 5,000 feet and the visibility is more than 5 miles.
The departure runway will only be given if different from the landing runway except at locations
having a separate ATIS for departure.
Frequencies for ATIS broadcast are available on IFR Enroute Charts, Terminal Low/High Altitude
Approach Plates, in the IFR Enroute Supplement and FAA Chart Supplement U.S.
WEATHER 12-15
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
ASOS/AWOS is the primary surface weather observing system of the U.S. The program to install
and operate these systems throughout the U.S. is a joint effort of the NWS, the FAA, and the
Department of Defense.
Most ASOS/AWOS sites also have a dial-up capability so that the minute-by-minute weather
messages can be accessed via telephone.
Pressure sensors (two sensors at small airports; three sensors at large airports).
Frequencies for ASOS/AWSS broadcast are available in the Terminal Low/High Altitude
Approach Plates, IFR Enroute Supplement, and FAA Chart Supplement U.S.
Automated weather reporting systems are increasingly being installed at airports. These systems
consist of various sensors, a processor, a computer-generated voice subsystem, and a transmitter
to broadcast local, minute-by-minute weather data directly to the pilot.
12-16 WEATHER
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK CHAPTER TWELVE
The AWOS observations will include the prefix “AUTO” to indicate that the data are derived
from an automated system.
Some AWOS locations will be augmented by certified observers who will provide weather and
obstruction to vision information in the remarks of the report when the reported visibility is less
than 7 miles. These sites, along with the hours of augmentation, are to be published in the FAA
Chart Supplement U.S. Augmentation is identified in the observation as “OBSERVER
WEATHER.” The AWOS wind speed, direction and gusts, temperature, dew point, and altimeter
setting, are exactly the same as for manual observations. The AWOS will also report density
altitude when it exceeds the field elevation by more than 1,000 feet.
The reported visibility is derived from a sensor near the touchdown of the primary instrument
runway.
The reported sky condition/ceiling is derived from the ceilometer located next to the visibility
sensor.
The AWOS algorithm integrates the last 30 minutes of ceilometer data to derive cloud layers and
heights. This output may also differ from the observer sky condition in that the AWOS is totally
dependent upon the cloud advection over the sensor site.
These real-time systems are operationally classified into nine basic levels:
NOTE
AWOS − l usually reports altimeter setting, wind data, temperature, dew point, and
density altitude.
AWOS − 3P provides reports the same as the AWOS 3 system, plus a precipitation
identification sensor.
AWOS − 3PT reports the same as the AWOS 3P System, plus thunderstorm/lightning
reporting capability.
WEATHER 12-17
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
AWOS − 4 reports the same as the AWOS 3 system, plus precipitation occurrence,
type and accumulation, freezing rain, thunderstorm, and runway surface sensors.
Frequencies for AWOS broadcast are available in the Terminal Low/High Altitude approach
plates, IFR Enroute Supplement and FAA Chart Supplement U.S. (Formerly called the
“Airport/Facility Directory”).
UNICOM service may be used for ATC purposes, only under the following circumstances:
ATC clearance, provided arrangements are made between the ATC facility and the
UNICOM licensee to handle such messages.
On pilot request, UNICOM stations may provide pilots with weather information, wind
direction, the recommended runway, or other necessary information.
UNICOM frequencies are available in the Terminal Low/High Altitude approach plates, IFR
Enroute Supplement and FAA Chart Supplement U.S. (Formerly called the “Airport/Facility
Directory”).
Availability of the automated UNICOM will be published in the FAA Chart Supplement U.S.
(Formerly called the “Airport/Facility Directory”), IFR Enroute Supplement, and Instrument
Approach Plates.
ATC radars are able to display areas of precipitation. All ATC facilities using radar weather
processors with the ability to determine precipitation intensity, will describe the intensity to pilots
as:
“Light”
“Moderate”
12-18 WEATHER
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK CHAPTER TWELVE
“Heavy”
“Extreme”
ATC facilities that, due to equipment limitations, cannot display the intensity levels of
precipitation, will describe the location of the precipitation area by geographic position, or
position relative to the aircraft. Since the intensity level is not available, the controller will state
“Intensity Unknown.”
ARTCC facilities normally use the Weather and Radar Processor (WARP) to display a mosaic of
data obtained from multiple NEXRAD sites. There is a time delay between actual conditions and
those displayed to the controller. For example, the precipitation data on the ARTCC controller’s
display could be up to 6 minutes old. When the WARP is not available, a second system, the
narrowband Air Route Surveillance Radar (ARSR) can display two distinct levels of precipitation
intensity that will be described to pilots as “Moderate” and “Heavy to Extreme.” The WARP
processor is only used in ARTCC facilities.
To the extent possible, controllers will issue pertinent information on weather or chaff areas and
assist pilots in avoiding such areas when requested. Pilots should respond to a weather advisory
by either acknowledging the advisory or by acknowledging the advisory and requesting an
alternative course of action. Be specific!
ATC radar is not able to detect turbulence. Generally, turbulence can be expected to occur as the
rate of rainfall or intensity of precipitation increases. Turbulence associated with greater rates of
rainfall/precipitation will normally be more severe than any associated with lesser rates of
rainfall/precipitation. Turbulence should be expected to occur near convective activity, even in
clear air. Thunderstorms are a form of convective activity that imply severe or greater turbulence.
Operation within 20 miles of thunderstorms should be approached with great caution, as the
severity of turbulence can be markedly greater than the precipitation intensity might indicate.
NOTE
Observed weather conditions reported by other pilots is one of the most valuable weather assets
available.
Pilots are also urged to promptly volunteer reports of cloud bases, tops, and layers, flight
visibility, precipitation, strong winds, and any other significant flight condition information.
WEATHER 12-19
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
A follow-on report should be passed to the nearest METRO (PMSV) to ensure rapid
dissemination to other using agencies. If flight conditions delay reporting to METRO while
airborne, ensure the PIREP is reported to METRO immediately after landing.
The PIREP format, PMSV frequencies and information on descriptors that should be used, is
found in the FIH SECTION C.
The DD Form 175-1, Flight Weather Briefing (also known as the Dash-One) is the military
standard briefing form. Whether you receive a verbal or written briefing, your briefing will
contain the elements contained on this form. Some blocks on the form may not be completed and
additional information may be included. The following section discusses the DD 175-1 format.
All time entries are in Zulu (Z). All heights are in hundreds of feet AGL/MSL. All winds are
entered in tens of degrees and speed in knots. All temperatures are in C, unless otherwise noted
or requested.
While this information is crucial for ensuring compliance with all weather requirements, it is also
needed in the preparation of a mission Flight Log and in computing TOLD data. (See Figure
12-5)
f. TEMP DEV (Temperature deviation, needed for the climb problem on the flight log)
i. SFC Wind (Surface wind, magnetic for local and true for remote locations)
12-20 WEATHER
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK CHAPTER TWELVE
m. Remarks/Takeoff ALTN FCST. (Any remarks on weather that will affect take-off
and climb (i.e., inversions, icing, and turbulence)).
PART II: ENROUTE & MISSION DATA (within 25 NM and 5000 Ft of flight level/route)
a. FLT Level Winds/TEMP (Flight Level winds in True, and outside air temperature.
This data will be needed for the cruise problem on the flight log and for avoiding
potential icing conditions).
b. Space Weather (Conditions such as sun spots or solar flares and the potential effect
on communication frequencies/GPS signals/and radio navigation aids)
c. Solar/Lunar (sunrise/sunset, moon rise, moon set and percent of moon illuminated
…BMNT (Begin Morning Nautical Twilight) and EENT (End Evening Nautical
Twilight) occur just before sunrise and just after sunset and are used for taking
reliable star sightings and bringing them to a still visible horizon during celestial
navigation).
d. Clouds at Flight Level (Appropriate block will be checked. A check in the "YES"
box represents a forecast for greater than 45% of the time spent in clouds at the flight
level in Block. A check in the "NO" box indicates less than 1% of the time will be
spent in clouds, while a check in the "IN AND OUT" box indicates between 1% and
45% of the flight will be through clouds).
e. Obscurations at Flt Level Restricting Visibility (Appropriate box will be checked and
include type of phenomenon restricting the visibility).
g. Maximum Cloud Tops-Location (Highest cloud tops and the geographical location)
i. Thunderstorms (If a thunderstorm warning is in effect for the route of flight it will be
listed here (in addition to Block 11 in Part I, which is for warnings applicable to the
local airfield). Any warnings listed here should also have comments made in the
remarks section (Part IV) to elaborate on the warning. The boxes can be checked to
indicate the type and amount of coverage, in addition to providing the maximum
cloud tops of the thunderstorms when that information is available, along with the
geographic location where the aircrew can expect to encounter the indicated
thunderstorm).
WEATHER 12-21
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
j. Turbulence (Advisories of turbulence will be noted here, any of which should also
have further remarks made in Part IV. Since turbulence will be experienced in all
thunderstorms, this section is only for turbulence not associated with thunderstorms.
The boxes can be checked to indicate the type and intensity of turbulence. Flight
levels and geographic location will be given for areas turbulence may be
encountered).
k. Icing (Icing advisory may be noted here. Boxes can be checked to indicate type and
intensity of icing. Geographic location will be given for areas icing may be
encountered).
b. Valid Time (Forecast times noted here will be valid through +/- 1 hour of the ETA
you provided).
c. SFC Wind (Forecasted winds will aid in selecting suitable a runway for use especially
if lost communications occur).
e. Cloud Layers (Type and levels of clouds will be noted here. Clouds that constitute
ceilings are a key element for determining if you are able to meet destination
approach minimums and alternate airfield selection requirements).
f. Altimeter/RWY TEMP/Press ALT (The lowest altimeter setting expected during the
valid period will be entered. This may be needed in the event of lost
communications. Runway temperature and pressure altitude will be needed to
compute TOLD data. Forecast will be valid through +/- 1 hour of ETA).
a. Briefed RSC/RCR (If Runway Surface Condition and/or Runway Condition Reading
for Destination and/or Alternate was provided or unavailable it is annotated here).
12-22 WEATHER
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK CHAPTER TWELVE
a. WX Briefed Time (Time the weather briefing was completed…the clock is ticking
from this point!)
c. Forecaster’s Initials
d. Name of Person Receiving Briefing (This will be the person who filed/received the
brief electronically or the person who received the brief verbally in person/via
phone.)
e. Void Time (This time shall not exceed the Weather Briefed Time in block 36 by more
than 3 hours and will not exceed ETD by more than 30 minutes.)
f. Extended To/Initials (If it appears that takeoff will occur outside the VOID time in
block 40, the weather brief needs to be updated. This must be accomplished before
takeoff. If the weather brief as first given is still applicable, then it may be extended
by a forecaster. The updated VOID time and forecaster’s initials will be entered here
by the aircrew.)
g. Weather Rebrief Time/Initials (If it appears that takeoff will occur outside the VOID
time and the weather brief as given is no longer applicable, then a complete re-brief
must be obtained. The VOID TIME in block 40 will be updated by the aircrew (same
CNAF rules apply). The time of the re-brief and forecaster’s initials will be entered
here by the aircrew.)
WEATHER 12-23
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
12-24 WEATHER
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK CHAPTER TWELVE
1. Before obtaining a flight clearance, a pilot must receive a weather briefing from a qualified
meteorological forecaster. (TRUE/FALSE)
2. The primary method for requesting and obtaining a flight route weather briefing is
________________________________________________.
3. The phone number for the Naval Aviation Forecast Center (NAFC) is ________________.
5. IFR flights through an area covered by a WW, CAWW, or Convective SIGMET are
authorized only under what conditions?
______________________________________________________________________________
______________________________________________________________________________
___________________________________________________________________________
KNGP 141256Z 35009KT 10SM OVC007 19/19 A2996 RMK A02 SLP150 T01940194
WEATHER 12-25
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
Questions 14-18 refer to the following minimums section of the only IAP for the airport in
question. Assume only CORPUS CHRISTI ALTIMETER SETTING is available.
14. If the ILS is available CNAF requires a minimum ceiling and visibility of
________________ in order to takeoff from runway 13R. If only the LOC is available then the
takeoff minimums become ______________________.
15. In order to commence the non-precision instrument approach to runway 13R at this
airport CNAF requires weather to be at least _____________________.
16. In order to commence the precision instrument approach to runway 13R at this airport
CNAF requires weather to be at least _____________________.
17. If the precision instrument approach to runway 13R at this airport is available, CNAF
requires forecasted weather to be at least _____________________ to use this airport as an
alternate for flight planning purposes.
18. If a NOTAM reports the ILS glideslope out of service for runway 13R, CNAF requires
forecasted weather to be at least _____________________ to use this airport as an alternate for
flight planning purposes.
19. CNAF requires flight plans shall be filed based what weather requirements?
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
20. The AIM states that a pilot can expect icing when flying in visible precipitation, such as
rain, or cloud droplets, and the temperature is between _____ and _____ degrees Celsius.
21. For preflight planning (more than 3 hours prior to planned takeoff), an excellent source
for weather data is the Aviation Weather Centers website. The web address for the AWC is
___________________________________.
12-26 WEATHER
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK CHAPTER TWELVE
22. In flight, common radio frequencies for FSS are ______ on VHF and _______ on UHF.
23. Information concerning PMSV and PIREPS can be found the _______ publication.
24. On your destination approach plate, in the communications section you note that
AWOS-3 is available. What information will be available to you on that frequency?
_________________________________________________________________________.
25. On the DD-175-1 the VOID TIME (block 40) shall never exceed the WX BRIEFED
TIME (block 36) by more than ________ and will not exceed the Estimated Time of Departure
by more than _____________.
WEATHER 12-27
CHAPTER TWELVE T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
12-28 WEATHER
CHAPTER THIRTEEN
FLIGHT LOGS
1300. INTRODUCTION
Before commencing a flight, the PIC shall be familiar with all available information appropriate
to the intended operation. Such information should include, but is not limited to, available
weather reports and forecasts, NOTAMs, fuel requirements, terminal instrument procedures
(to include proper use of non-DoD approaches), alternatives available if the flight cannot be
completed as planned, and any anticipated traffic delays. In addition, the PIC and mission
commander (when there is one designated) shall conduct a risk assessment prior to the flight.
Regardless of weather, IFR flight plans shall be filed and flown whenever practicable as a means
of reducing midair collision potential. In any case, forecast meteorological conditions must meet
the weather minimum criteria (See Figure 13-1) for filing IFR flight plans and shall be based on
the pilot's best judgment as to the runway that will be in use upon arrival.
For T-6B training, a 300 NM leg provides adequate fuel to fly the route and allow for
multiple practice approaches.
GP: Flights should be planned and flown via, preferred IFR routes, SIDs or published
airways (if available) for the first 200 NM of flight from the departure point.
GP: Arrival should be planned via STARs, published preferred IFR routes or
published airways (if available) for the final 200 NM of the route flown.
GP: Aircrews should ensure that their route of flight will avoid active restricted areas
by at least 3 NM, unless permission has been obtained from the using agency to
operate in that airspace, and the appropriate ATC facility has been notified.
The following 14 step checklist is recommended to ensure compliance with CNAF M-3710.7
requirements during preparation of a Flight Log. A properly completed Flight log will aid in
filing the flight plan and provide essential data while inflight.
1. Examine Origin
e. Check Airfield Services (ensure contract fuel is available if not DoD) using AIR Card
FBO locator. Webpage and phone number for Air Card can be found in the ES
legend data under FUEL.
g. Check Runway Length and location of barriers (arresting gear) (ES/T LA-HA).
k. Check for CNAF Takeoff minimums: (verify again once clearance is received).
(a). Precision Approach - published mins but not less than 200-½ or 200/24
(b). Nonprecision Approach - published mins but not less than 300-1
2. Examine Destination
d. Check Airfield services (ensure contract fuel is available if not DoD) (ES).
3. Examine Alternate
i. Departure airport
a. Record climb winds and ∆T (From DD-175-1 or ADDS website) on flight log.
i. Climb Winds
i. Use PCL “Time, Fuel, and Distance to Climb” for Time to Climb (TTC), Climb
Fuel and Distance covered during the Climb.
c. Compute the average Climb TAS and Fuel Flow using the CR-3
a. Use NATOPS PCL “Long Range Cruise” table to extract IAS, TAS and Fuel flow for
the planned Cruise altitude. (interpolate between closest altitudes/temperatures)
a. First leg entry is always STTO, (1 minute and 50# Fuel unless you expect more)
c. Enter the NAVAID and Frequency data as required for each leg.
i. Round distances off to the nearest whole number for each calculation
(.5 or greater rounds up).
ii. Magnetic course and distance from the departure airfield to the first fix
(Intersection or NAVAID) on an airway may be determined from the Enroute
Supplement airports NAVAID section, on the Approach Plates (as
Enroute/Feeder Fixes), or may be determined using Enroute charts.
b. A common technique for annotating compulsory reporting points on the Flight Log is
to place a mark in the “Route To" column for any leg that would constitute a
mandatory reporting point in the event a non-radar environment is encountered.
c. For instances where part of a leg is climb and part is cruising (split-leg) record both
groundspeeds (climb first followed by cruise).
a. Rounding procedures:
ii. Fuel: any fraction over a 5 pound increment, round up to the next 5 pound
increment. Example: 42 lbs rounds up to 45 pounds.
(c). Note time (on inner scale) below Leg 1 DIST. If less than PCL TTC enter
time as Leg 1 ETE.
(d). If PCL TTC (on inner scale) is less than Leg 1 distance, enter PCL TTC as
split entry for Leg 1 ETE. Read Distance for climb (on outer scale) above
PCL TTC. Enter Climb Dist as split entry for Leg 1 Dist (the remaining
Leg 1 Dist is Cruise Dist)
(e). Repeat (as required) for subsequent Legs using remaining TTC until
level-off Dist/ETE is determined.
(d). Enter Leg Cruise ETE on Flight Log (use spilt entry for Leg with
Climb/Cruise Dist).
(c). Read Climb Fuel on outer scale above Leg Climb ETE.
(d). Enter Leg Climb Fuel on Flight Log (Use split entry for Leg with
Climb/Cruise ETEs).
(c). Read Cruise Fuel on outer scale above Leg Cruise ETE.
(d). Enter Leg Cruise Fuel on Flight Log (Use split entry for Leg with
Climb/Cruise ETEs)
b. Subtract STTO fuel and enter difference in the EFR bock of the STTO line
c. Subtract estimated fuel for Leg 1 from the EFR in the line above it and enter
difference in EFR block for Leg 1.
a. Add ETE from last Fix at the Destination (prior to the approach) to the time required
to complete an approach at the Alternate airport (typically 10 minutes).
b. Record sum in the TIME block on the Alternate line of the Flight Log.
a. Climb/Route to Dest (fuel used after takeoff to the last fix at the destination prior to
the approach…does not include STTO fuel)
b. Route to Alternate (fuel required from last fix at the destination prior to the approach
to the last fix at the Alternate prior to the approach)
c. Approaches (Plan 50 lbs for each approach unless more is known to be required.)
e. Reserve (For T-6B operations this will be 115 lbs to meet the CNAF requirement for
minimum of 20 mins. @ Max endurance 10,000 feet. More may be required for
local sop.)
f. Start/Taxi (50 lbs for default unless excessive ground delays are expected)
h. Total Fuel Aboard (1100 for normal fuel load… may get more with over the wing
refueling…or less if the refueling operator is in a hurry. Check the gauges before
flight!
i. Spare Fuel (Line 8 Total Fuel Aboard minus Line 7 Total Fuel Required.
You have been tasked to research and plan a mission for an IFR flight from the Hattiesburg
Bobby L Chain Municipal Airport (KHBG) in Hattiesburg, Mississippi to Naval Air Station New
Orleans (KNBG) in New Orleans, Louisiana.
Departing: Hattiesburg at 0700 local on Tuesday 02 JUNE 2016. (Daylight Saving Time is in
effect).
Ideally you will start your flight planning process 24 hours prior to your departure. During our
research we will use the Flight Planning Matrix to organize the data. (See Figure 13-2) The
more detailed your notes, the more flexible you can be should weather, or mission changes
require re-examination your route.
1. The IFR enroute supplement can be used to determine which enroute charts will be
required for your route. Airport information in the ES includes which Enroute chart and panel
airfields are located on. (See Figure 13-3) Once you have the charts gathered decide on a
logical route for your particular flight. From your departure airport, you normally enter the route
structure at an intersection or a NAVAID. From there you can fly airways, or direct to a
particular NAVAID. Some airfields may have specific departure procedures (DPs) listed in the
airport’s FLIP Terminal publications (a.k.a. approach plates).
2. Locating our Origin, Destination and then factoring in any required training along the way,
choose a basic route. Depart KHBG proceed to LBY V543 to RAYOP intersection then direct to
HARVEY VORTAC (NBG). (See Figure 13-4)
3. While looking at your destination airfield, select possible alternates to research for your
flight. For this particular problem we will research New Orleans International (KMSY), Bay St
Louis, Stennis INTL (KHSA), and Houma-Terrebonne (KHUM) as possible alternates.
4. Based on your ETD and approximate ETAs, obtain TAFs for the origin, destination, and
alternate airfields. You can do your initial flight planning based on weather obtained from the
FAA ADDS website. (See Figure 13-5) On the day or your flight you are required to get an
Official Weather brief (preferably a DD-175-1). (See Figure 13-6) This information will be
used to finalize your Flight log specifics such as time in route and fuel burns.
5. Select an altitude for your route. Considerations for selecting a cruising altitude should
include; winds aloft, weather, freezing levels, IFR cruising altitudes, MEA’s along the proposed
route and mission needs. Generally, 10 percent of the total distance will equal and altitude in
thousands of feet that will provide a fuel efficient profile. Our total distance today is
approximately 125 NM therefore an altitude in the vicinity 12,500 feet MSL would be efficient.
For this exercise we will use 16,000 feet.
The Airport Data Matrix located on the back of the Flight Log (Figure 13-7) is used to record
data that may be needed while inflight. While the Flight Planning Matrix, (Figure 13-2) contains
much of the same information it is useful during the planning phase.
1. Examine Origin airfield NOTAMS (this is a good time to pull NOTAMS for the
destination, proposed alternates, enroute and GPS as applicable).
2. Check Airfield operating hours. Use the IFR Enroute Supplement to determine airfield
hours of operation. All times are listed in ZULU. To convert ZULU to local time use the
appropriate correction listed in the Enroute Supplement. The correction will depend on whether
Day Light Saving Time is being observed. Watch for ++ symbols following times which
indicate that effective hours will be one hour earlier during periods of daylight saving time
(See Figure 13-9).
KHBG is a non-towered airport (no Class D airspace noted on the L-22 Chart) and they are in
operation during daylight hours (See Figure 13-8).
3. Check Airfield Services. Research enroute supplement for services and fuel available at
the airfield (See Figures 13-8, 13-9). Note availability of fuel compatible with the T-6. For
civilian fields, check to see if they have a government contract authorizing them to sell fuel. All
military airfields are authorized to sell fuel to transient military aircraft.
KHBG has Jet A with additive available 0700-1700 Monday through Friday, 0800-1700
Saturday and Sunday.
4. Check Airfield Remarks (hazards). Sources for hazards include; NOTAMs, AP/1, and the
Enroute Supplement remarks/caution section. Additionally, FAA Chart Supplements (formerly
known as the Airport/Facilities Directory) has information on civil airports similar to that found
in the FLIP ES. An FAA Chart Supplement Search (by State/Airport) is available online at the
FAA website: http://www.faa.gov/air_traffic/flight_info/aeronav/digital_products/dafd/search/
5. Check Runway Length and location of barriers (arresting gear). Review the ES for
pertinent information concerning the departure runway.
Forecasted winds favor runway 31. The IFR enroute supplement shows KHBG runway 13/31 to
be 6,094 feet long, 150 feet wide with an asphalt surface. There is no arresting gear or barriers
listed.
7. Select type of departure to be used. KHBG has a Standard Instrument Departure (SID)
labeled the EATON ONE DEPARTURE (LBY1.LBY). (See Figure 13-10) As recommended in
the GP, we will employ this DP leaving KHBG. Trouble T information applicable to the
EATON ONE is conveniently located on the SID. Textual information/instructions when
departing other than via the SID is available in the front of the approach plates.
(See Figure 13-11)
Winds favor a runway 31 departure. CNAF Takeoff Weather requirements are based on
returning to the runway in use in the event of an emergency during departure. The only
instrument approaches available to KHBG are to runway 13. Therefore, our departure weather
requirements will be based on an approach to runway 13 and circle to land runway 31. We will
examine the departure procedures for this runway and comply with all climb restrictions.
Required weather for all instrument departures will be derived using CNAF criteria.
9. Check for CNAF take-off minimums. Standard instrument rating: CNAF requires that
weather for departure allow for an emergency return for the landing runway in use.
Non-Precision Approach (NPA): Published minimums for the available approach but not less
than 300-foot ceiling and 1-statute mile visibility.
Precision Approach: Published minimums for the available approach but not less than 200-foot
ceiling and 1/2-statute-mile visibility/2,400-foot runway visual range (RVR).
Winds favor a runway 31 departure. The only options available for return to that runway are
non-precision approaches to runway 13, circle to land on runway 31.
Check circling minimums for a runway 13 approach (See Figure 13-12). The weather on our
DD Form 175-1 for our ETD (See Figure 13-6) meets the minimum 500-1 required to safely
takeoff and return to runway 31 should and emergency arise during departure.
(Check weather again prior to departure. Weather must meet minimums when clearance is
received.)
As origin information is gathered, record all notes and findings on the Flight Data and the
Airport data matrixes. (See Figures 13-3 and 13-4)
1. Ensure airfield is authorized for use. CNAF M-3710.7 section 4.4 sets the requirements for
authorized airfields. Look at the operating agency for the airport in the ES. Typically, military,
joint use military/civil airports are good. In the ES, operating agencies listed with a “P” are US
civil airports wherein permit covers use by transient military aircraft.
Check ES for any noted restrictions. Under remarks, a PPR (Prior Permission Required) is
listed.
3. Check airfield hours of operation. Using the appropriate conversion from ZULU and
accounting for the ++ symbol we find KNBG operating hours to be 0700-2300 local MON-SAT.
4. Check Airfield Services. Look for T-6B compatible fuel, servicing times, restrictions, and
contract fuel availability (for civil fields). KNBG has Military supplied J-8 fuel (which is
compatible with the T-6). Service is available 0730-2230.
In the ES under SERVICE, note that the Arresting gear is maintained in the raised position is in
battery at all times, do not land directly on the cable (for the T-6B plan to land beyond the cable).
In the ES under RESTRICTIONS, note that a PPR (Prior Permission Required) number will be
required for all aircraft. Your arrival must be approved and base operations. They require a
48 hour Prior Notice that you are coming. The DSN (Defense Switching Network) and
commercial phone numbers needed to obtain the PPR number are listed in the remarks section.
This PPR number will be needed for your IFR flight plan.
Note the information under CAUTIONS in the ES as well. Example: Overhead break is at
1500’ and pattern altitude is 1000’.
AP1 has supplemental information concerning selected airports. KNBG is listed in the AP1. Be
aware of all information here such as noise abatement procedures for departures but especially
note the CAUTION section. Example: The intersection of Taxiway A and F, the Air
Sovereignty Alert Facility and the CALA Pad are not visible from the tower.
6. Check for applicable STAR. Around major airports (Such as New Orleans International
KMSY), and airports in or near Class B airspace check for possible Standard Terminal Arrival
Routing for the arrival area. The legend in the front of the STAR book lists affected cities
alphabetically. Under the city, each airport affected has the individual STARs arranged
alphabetically by the name of the STAR. While KNBG is not listed under the airports for New
Orleans. However, to avoid possible delays it would be prudent to use the conventional route
that mirrors the STAR if possible. (See Figures 13-16 and 13-17)
The forecasted weather for KNBG is 700 Broken, 2 NM in haze and mist, and winds 310 at
10 knots which favors runway 32.
NOTAMs at KNBG for our estimated time of arrival indicate that; RAIM insufficient for RNAV
approaches, Localizer is out of service Until Further Notice and KNBG is not accepting radar
approaches.
Check Volume 14 of the Terminal Low Altitude approach plates to see what approaches are
available. Landing on runway 32 will require a circling approach that is compatible with our
aircraft. A VOR/DME approach is available to both runways 04 and 22. Circling minimums are
600-1 for both approaches. This meets the CNAF actual instrument approach minimums of
200-1/2 for single piloted aircraft. We will use the VOR/DME RWY 04 circle to land runway
32. (See Figure 13-19)
8. Record all data on the Flight Planning Matrix. As Destination information is gathered,
record all notes and findings on the Planning/Flight Log Matrixes. (See Figure 13-18)
CNAF: Destination weather for our ETA plus and minus 1 hour is above published minimums
but is less than 3000-3. This (CNAF case 2) will require us to file an alternate. In this situation,
the weather requirements for an approach at the alternate will have to meet CNAF Alternate
requirements of Published minimums plus 300-1 for a non-precision approach and Published
minimums plus 200-1/2 for a precision approach. (See Figure 13-1)
Naval aircraft are authorized to operate at and land at all U.S. military and joint civil-military
airfields. When planning to operate at other than home airfields, local training airfields, or
outlying landing fields (OLFs), pilots in command shall ensure that they are aware of and meet
airfield operating requirements and, when necessary, have satisfied prior permission required
(PPR) requirements. PPRs need not be obtained for planned alternate fields or emergency
divert airfields.
In the case of single piloted aircraft, radar/airport surveillance approach (PAR/ASR) minimums
may not be used as the basis for selection on an alternate airfield (See Figure 13-1)
Because the cost of fuel from non-contract commercial sources is considerably higher than that
from military or contract sources, unit commanders and PICs shall make every effort to purchase
fuel from military or government contract sources. Navy and Marine Corps flight personnel
are not authorized to purchase aircraft fuel/oil from other than military or government
contract sources except when one of the following apply:
While CNAF may not require contract fuel to be available at an alternate, it may be worth
checking the ES and selecting one that does.
ALTERNATE 1 KMSY:
Our route will be flown at 16,000 feet. A search of the Terminal High (East) approach plates
reveals no high altitude approaches for KMSY.
The Terminal Low Altitude VOL 14 approach plates have several Non-GPS/Radar approaches at
KMSY that are compatible with the T-6B.
Forecasted winds favor runway 2 at KMSY (RWY 29 is closed). The approach with the lowest
weather requirements to runway 2 is the precision approach portion of the ILS or LOC RWY 2
approach. Published weather mins for ILS (precision approach) are 400-1 ¼. (See Figure 13-21)
To satisfy the CNAF alternate requirements we must increase the published minimums by
200- ½ for alternate planning when considering a precision approach. Therefore, KMSY must
be forecasted to have 600 -1 ¾ plus or minus one hour from our estimated time of arrival to serve
as an alternate. Our DD Form 175- shows KMSY forecast to be 2000-1. While the ceiling is
much greater than required, the visibility is below the required alternate minimums. We are
unable to file KMSY as an alternate airfield.
Remember to keep track of your research on the flight data matrix. (See Figure 13-20)
ALTERNATE 2 KHSA:
A search of the Terminal High (East) approach plates reveals no high altitude approaches for
KHSA.
The Terminal Low Altitude VOL 14 approach plates have 2 NON-GPS/RADAR approaches at
KHSA compatible with the T-6B. Both are to runway 18.
Forecasted winds favor runway 36 at KHSA. This will require an approach to runway 18
circling to land on runway 36.
The allowable/compatible approach with the lowest circling minimums is the VOR-A.
Published weather minimums for this circling approach are 500-1. (See Figure 13-22)
To satisfy the CNAF alternate requirements we must increase the published minimums by 300-1
for alternate planning when considering a non-precision approach. Therefore, KHSA must be
forecasted to have 800-2 plus or minus one hour from our estimated time of arrival to serve as an
alternate. Our DD Form 175- shows KHSA forecast to be 800-2. We have weather
requirements to use KHSA as an alternate airfield however, the must be checked.
(See Figure 13-23)
Remember to keep track of your research on the flight data matrix. (See Figure 13-24)
Alternate 3 KHUM:
A search of the Terminal High (East) approach plates reveals no high altitude approaches for
KHUM.
The Terminal Low Altitude VOL 14 approach plates have 2 NON-GPS/RADAR approaches at
KHSA compatible with the T-6B.
Forecasted winds favor runway 30 at KHUM. The VOR/DME RWY 30 has non-precision
straight-in minimums of 400-1 (See Figure 13-25).
To satisfy the CNAF alternate requirements we must increase the published minimums by 300-1
for alternate planning when considering a non-precision approach. Therefore, KHUM must be
forecasted to have 700-2 plus or minus one hour from our estimated time of arrival to serve as an
alternate. Our DD Form 175- shows KHUM forecast to be 800-2 1/2. We have weather
requirements to use KHSA as an alternate.
Keep track of your research on the Planning/Flight Log Matrixes. (See Figure 13-27)
Using the IFR Enroute Supplement or Approach Plates record the airfield elevation and available
communication frequencies for the Origin, Destination and Alternate airports on the Flight Log.
(See Figure 13-28)
1. Record Wind and Temperature data for Climb and Cruise on the Flight Log.
Using the DD-175-1 obtain and record the following data onto the Flight Log:
(See Figure 13-29)
a. Climb Winds
b. Cruise Winds
Using the TIME, FUEL, AND DISTANCE TO CLIMB table from the NATOPS PCL determine
the Time to Climb (TTC), Fuel needed for the climb and Distance covered during the Climb.
This table is calculated based on; no drag (clean configuration), no wind, Climb IAS 140 KTS,
6,900 LBS, and Max Climb Power. On the table, find the intended cruise altitude on the left.
Then under the appropriate Temperature Deviation from Standard (∆T), extract the Time, Fuel
and Distance raw data. (See Figure 13-30)
At 16,000 feet, with a ∆T of +20°C the TTC will be 8 minutes, require 78 LBS of fuel and cover
a no wind distance of 23 NM.
3. Compute the average Climb TAS and CLIMB Fuel Flow using the CR-3
i. Set the 8 minute TTC on the inner scale under the no-wind CLIMB distance of
23 NM on the outer scale.
ii. Above the Indexer read the average Climb TAS of 173 KTS
(See Figure 13-32)
b. Determine average Climb Fuel Flow. 78 pounds of fuel will be expended during the
8 minute climb. On the CR-3:
i. Set the 8 minute TTC on the inner scale under the 78 LBS of fuel used on the
outer scale
ii. Above the Indexer read the average Climb Fuel Flow of 585 pounds per hour
(See Figure 13-33)
c. Record CLIMB TAS and Fuel Flow on the Flight Log. (See Figure 13-34)
1. Use the NATOPS PCL Long Range Cruise Table to extract IAS, TAS and Fuel flow for
the planned Cruise altitude. (See Figure 13-35)
While this table does not provide data for every possible altitude and temperature combination,
interpolating between the 15,000 feet and 20,000 feet data at -15°C OAT we can estimate a
Cruise TAS of 245 KTS, Cruise Fuel Flow of 387 PPH and a Cruise IAS of 189 KTS at
16,000 feet.
1. The first Leg entry in the “ROUTE” section of the Flight Log will be for Start, Taxi, and
Takeoff (STTO).
This will line is used to account for fuel burned on the ground and time for the initial takeoff roll.
50 pounds of fuel and one minute of timing for this Leg is used as a default for normal
operations. Adjust as required for known or expected delays. (See Figure 13-37)
i. At each NAVAID
c. The SID EATON ONE DEPARTURE, takes us to the EATON VORTAC, from there
we intercept V543 RAYOP intersection (mirroring the route depicted in the
RHYTHM FOUR ARRIVAL). We expect to do the VOR RWY 4 approach utilizing
the TINEE as the IAF.
3. Enter the NAVAID and Frequency data as required for each leg.
Under the IDENT/CHAN, list the NAVAID three letter identifiers and frequencies needed to
navigate each leg.
Even when navigating with GPS waypoints, list back up NAVAIDS where possible.
Round distances off to the nearest whole number for each calculation (.5 or greater rounds up).
The first course/distance from the departure airfield may be found on an approach plate for that
airfield, the IFR enroute supplement or measured directly off the appropriate Enroute Chart.
A course/distance from EATON VORTAC to KHBG can be found in the NAVAID SECTION
OF THE IFR Enroute Supplement (150°/10.2 NM). The reciprocal of this course will be a
course direct from KHBG to LBY (330°/10.2 NM). (See Figure 13-38)
The courses and distances for the next few legs can be read from the low altitude chart since we
are flying along airways. They can also be taken from the STAR “RHYTHM 4 ARRIVAL.”
(See Figure 13-16)
The last Leg is Direct from RAYOP to TINEE (IAF). TINEE is not located on the Enroute
chart. It will need to be plotted onto the Enroute chart using data from the approach plate. Then
course and distance can be measured using the Enroute Chart. The KNBG VOR/DME or
TACAN RWY 4 approach shows TINEE located on the HRV 226° R at 15 NM (See Figure
13-19).
Route to the alternate will be planned from the last fix at the destination prior to the approach
(usually an IAF) then via a planned route to the alternate airport (IAF, NAVAID, first point of
intended landing, or published fix which most clearly establishes the route of flight to the
alternate airport). For our example from TINEE we will use direct to the TIBBY VORTAC
(TBD) then direct to BOURG (IAF for KHUM VOR/DME RWY 10).
While uncommon, loss or radar contact may occur at any time during your flight.
The Flight Information Handbook Section B reiterates that Federal Aviation Regulations require
pilots to furnish position reports passing certain reporting points when operating in a non-radar
environment. The FIH details procedures for those reports should they become necessary.
A common technique for annotating compulsory reporting points on the Flight Log is to place a
mark in the “ROUTE TO" column for any Leg that would constitute a mandatory reporting point
in the event a non-radar environment is encountered.
Along our selected route the Enroute chart has no NAVAIDS, intersections, or waypoints
depicted as compulsory reporting points; however, the legs from RAYOP to TINEEE and TBD
to BOURG are direct. Therefore, all four intersections would become compulsory reporting
points should a non-radar environment exist.
1. Determine CLIMB Groundspeed(s) (no-wind average TAS adjusted for climb winds).
On the CR-3 plot the Climb Winds of 300/20 True from the DD-175-1. (See Figure 13-40)
When using True Winds to calculate groundspeed based on magnetic courses, local magnetic
variation must be applied.
Magnetic variation is annotated on the Enroute Charts by a solid green line. This can be used to
obtain an average variation along North-South routes. East-West routes may require that
different variations be applied for each leg. Exact magnetic variation is depicted on Airport
Diagrams for selected airports in the approach plates.
On the Enroute Chart our selected route lies very near the 1°W line of magnetic variation. The
Airport Diagram for our destination depicts magnetic variation at the airport to be 0.7°W
(See Figure 13-41). We will use 1°W variation for our calculations.
– On the CR-3:
i. Place the first (magnetic) Leg course used for the climb (346°) under the 1°W
variation mark just right of the TC indexer (See Figure 13-42).
iii. Our no-wind average climb TAS of 173 knots less the 14 knot headwind results
in a Climb groundspeed of 158 knots for the first leg.
Due to the length of the next Leg we will need to have a double entry. For the first portion of
this Leg we will be continuing our climb up to 16,000 feet.
Repeating the procedure noted above using a magnetic course of 216° with a 1°W variation with
the same winds results in a 2 knot headwind and 170 groundspeed for the remainder of the
climb on the second leg.
– On the CR-3:
ii. Place the Leg 2 course of 216° under the 1°W variation.
iii. Interpret the wind plot and note a 9 knot tailwind added to our CRUISE TAS of
245 knots results in a Cruise groundspeed of 254 knots for the remainder of
the second Leg to RYTHM. (See Figure 13-43)
3. Repeat this process for the remainder of the cruise legs (including those to the Alternate).
Record the groundspeeds for each Leg on the Flight log in the GS column. (See Figure 13-44)
Rounding guidelines:
Fuel: Any fraction over a 5 pound increment, rounds up to the next 5 pound
increment. Example: 42 lbs rounds up to 45 pounds.
The Total Time to Climb (TTC) of 8 minutes is taken directly from the PCL. The PCL climb
distance is based on no-wind and should be corrected for actual groundspeed. Determining the
corrected Climb DIST will fix the point where calculations stop using Climb groundspeed/fuel
flow data and begin using Cruise groundspeed/fuel flow data.
TTC to 16,000 feet is given as 8 minutes. Leg 1 DIST to EATON VORTAC is 10 NM. Place
Leg 1 Climb groundspeed of 158 knots on the CR-3 indexer.
Under the Leg 1 DIST of 10 NM read approximately 3.8 minutes. Rounded to the nearest
minute we will use 4 minutes for Leg 1 ETE. EATON VORTAC will be reached in 4 minutes.
The remaining 4 minutes of TTC will be completed on Leg 2. (See Figure 13-45)
Read remaining Leg 2 Climb distance of approximately 11.3 NM on the outer scale
(rounded to the nearest mile, we will use 11 NM). (See Figure 13-46)
With 11 NM of Leg 2 is used for Climb, the remaining 58 NM of Leg 2 will be accomplished at
Cruise. The Leg 2 DIST entry will show this split as 11/58 along with the combined sum of 69.
Leg 2 ETE will also be a split entry with the Climb ETE of 4 minutes and the remaining Leg 2
Cruise ETE which will be computed using cruise groundspeed.
Read the time it will take to complete Leg 2 on the inner scale. For 13.7 minutes
rounded to the nearest minute, we will use 14 minutes as the time to complete the
remaining portion of Leg 2. (See Figure 13-47)
Total Leg 2 ETE can now be determined by adding the Leg 2 Climb ETE of 4 minutes with the
Leg 2 Cruise ETE of 14 minutes for a total Leg 2 ETE of 18 minutes.
The Leg 2 ETE entry will show this split as 4/14 along with the combined sum of 18.
Compute the remaining Leg ETEs (including the alternate Legs) using the corresponding Leg
DIST and Leg Cruise groundspeeds.
Total the DISTs from takeoff through the last entry for the destination and enter the sum below
the last DIST entry in the top portion of the Flight Log.
Total the ETEs from takeoff through the last entry for the destination and enter the sum in an hrs
+ min format below the last ETE entry in the top portion of the Flight Log.
Total the DISTs for the Alternate route (from the last fix at the destination to the last fix at the
alternate prior to the approach). Enter the sum below the last DIST entry in the bottom portion
of the Flight Log.
Total the ETEs for the Alternate route (from the last fix at the destination to the last fix at the
Alternate prior to the approach). Enter the sum in an hrs + min format below the last ETE entry
in the bottom portion of the Flight Log.
Figure 13-48 shows the Flight log completed through Step 10.
With known fuel flow and Leg ETEs fuel usage can now be computed. The first entry for STTO
is given at 50 lbs. Keep in mind if you expect delays on the ground you may need to adjust this
value (busy/large airports).
Place the Climb fuel flow of 585 PPH on the CR-3 indexer.
Read the fuel used of 39 pounds on the outer scale (See Figure 13-49).
Rounding any fraction over a 5 pound increment up to the next 5 pound increment
use 40 pounds as Leg 1 Fuel. (Because Leg 1 is completed entirely while climbing
this will be the total LEG 1 fuel entry.)
Place the Climb fuel flow of 585 PPH on the CR-3 indexer.
Read Climb fuel used of 39 pounds on the outer scale (See Figure 13-49)
Rounding any fraction over a 5 pound increment up to the next 5 pound increment
use 40 pounds as Leg 2 Climb Fuel. (Leg 2 Fuel will be split between Climb and
Cruise. Enter 40/ for Leg 2 Climb Fuel)
Place the cruise fuel flow of 387 PPH on the CR-3 Indexer
Find the remaining Leg 2 Cruise ETE of 14 minutes on the inner scale
Read Cruise fuel used of 90 pounds on the outer scale (See Figure 13-50)
No rounding is needed in this case. Enter 90 pounds as the split Cruise Fuel for
Leg2.
Leg 2 Fuel will show 40 pounds used for Climb Fuel and 90 lbs for Cruise Fuel. This
split fuel 40/90 and the combined total of 130, is entered on the Flight Log as Leg2
Fuel.
Repeat the computations for all remaining Legs (including legs to the Alternate) using Cruise
Fuel Low of 387 PPH and the Leg ETEs.
Total all fuel estimated from STTO to the last destination Fix. Annotate it the Leg Fuel column
in the upper portion of the Flight Log.
Total all Alternate Leg fuels. Annotate it the Leg Fuel column in the lower portion of the Flight
Log.
Keeping track of fuel usage is vital to ensure a successful mission. Calculating EFR (Estimated
Fuel Remaining) for each leg of the flight will serve as an important benchmark to evaluate fuel
usage.
During the flight, having AFR (Actual Fuel Remaining) exceed EFR for each Leg would be a
welcome situation; however, if AFR is less than EFR the end of a Leg the aircrew should begin
an immediate investigation for the cause.
Fuel leak
The sooner a reason for increased fuel usage is determined, the more options the aircrew will
have. Waiting until the low fuel lights come on is not the time to start considering fuel options.
Monitoring fuel usage is a key part of the OPS Check. The EFR column on a properly
completed Flight Log is a tremendous aid for situational awareness.
A normal fuel load for the T-6B is 1100 lbs when using single point refueling. An additional
100 lbs can be added using over the wing refueling. Never assume the ground crew took care of
it for you. Check the fuel gauges! For our problem we will use 1100 lbs as our initial fuel load.
2. Subtract the 50 lbs fuel for STTO from the total fuel onboard and enter the result in the
EFR block for the STTO line.
3. Subtract fuel for Leg 1 from the EFR from the line above it and enter the difference in the
EFR block for Leg 1.
4. Repeat this process for all remaining Legs (including the alternate Legs).
Figure 13-52 shows the Flight Log completed through Step 11.
This step will estimate the amount of flight time available in Hours + Minutes after reaching the
last fix prior to the approach at the intended destination.
This computation will be made using the EFR at the last fix prior to the approach at the
destination and the planned Cruise Fuel Flow.
c. Read remaining flight time available of 125 minutes on the inner scale below 805 lbs
d. Record fuel remaining in Hrs + Min format (2+05) in the FUEL column of the
Alternate line on the Flight Log (See Figure 13-54)
On the DD Form 1801 Flight Plan, item 19 Endurance Fuel will represent the total flight time
possible (in Hrs + Min) based on your flight profile.
It is the sum of the ETEs used from takeoff to the last fix at the destination prior to the approach
plus the Fuel remaining at that point.
For our profile, that would be 0+34 plus 2+05 for a total fuel onboard of 2+39.
DRAFT is a mnemonic that can be used for the report made to Air Traffic Control when
requesting clearance to an alternate airport.
Once we complete the Time block on the Alternate line, we will have all data needed should
such a report be required.
1. Compute the Time required from the Destination to the Alternate Airport.
Total the ETEs from the last fix at the Destination to the last fix at the Alternate. We have
already totaled these numbers and annotated it in the bottom portion of the Flight Log. In our
example it is 0+13.
2. Enter the ETE in the Time block on the Alternate line of the Flight Log. In our example
the Time entry will be 0+13. (See Figure 13-55)
Upon arrival at our destination, if weather or circumstances will not permit an approach, we
could request clearance to our alternate by reading the information from the Alternate Line on
the Flight Log:
“Navy 2E095 request clearance to my Alternate; HOUMA TERREBONNE, via direct TIBBY
direct BOURG at 16 thousand, Fuel 2+05, Time 0+13”
CNAF requires that all fuel needed for the mission be accounted for along with an adequate
reserve. The Fuel Plan on the Flight Log is used to accomplish this requirement. (See Figure
13-56)
The majority of this data has already been computed and recorded on the Flight Log. This
section is used to compile fuel requirements.
1. Climb/Route To DEST
This entry reflects total fuel used after STTO to the last Fix at the destination prior to the
approach. 245 lbs for our example (we will add the fuel for STTO in block 6).
2. Route To Alternate
This entry will be the total fuel used from the last Fix at our destination to the last fix at our
Alternate prior to the approach. 90 lbs for our example
3. Approaches
The total amount of fuel for planned approaches. 50 lbs per approach is the normal. We are
only planning for one approach in our example. Additional planned practice approaches should
be included here.
4. Total 1,2,3
Add the planned fuel from items 1, 2, and 3. For our example; 245+90+50=385
a. This entry represents fuel that should set aside for safety. This fuel should not
“Planned to be used.”
b. CNAF requires that this should be 10% for the total fuel on line 4. This would be
38.5 lbs in our case. Rounded up the value would be 40 lbs; however, CNAF further
states that this value shall never be less than enough fuel to fly for 20 minutes at
10,000 feet computed using the aircrafts Maximum Endurance fuel flow.
c. The NATOPS PCL “Maximum Endurance Cruise” table (See Figure 13-57) shows
fuel flow at 10,000 feet on a standard day to be 333 PPH. Divided by three, the 20
minute value would be 111 lbs. Using our fuel rounding rule this will be 115 lbs.
d. This number may be further increased if required to comply with Local SOP
requirements.
6. Start/Taxi
Here we enter the fuel estimated for start, taxi, and initial takeoff roll. Remember that while we
use a default of 50 lbs for the T-6B more may be needed where extended ground time is
expected.
This line represents all fuel expected to be expended for the mission profile. Adding lines 4, 5
and 6 together we have 550 lbs for our example.
Maximum with SPR (Single Point Refueling) is 1100 Lbs. This may be increased to 1200 Lbs if
over the wing refueling is employed. For our example we are using 1100 lbs.
9. Spare Fuel
This is the Line 8 Total Fuel Aboard minus Line 7 Total Fuel Required, 550 lbs in our example.
Knowing how much spare fuel is available will aid the decision making process during mission
execution should un-forecasted weather or other circumstances occur.
Record all results on the T-6B Fuel Plan portion of the Flight Log. (See Figure 13-58)
1. For a pilot holding a Standard Instrument rating, CNAF requires the weather for departure
airfield allow for an emergency return to the landing runway in use. Takeoff weather must meet
published minimums for the approach in use but never less than ____________ for a precision
approach or less than ____________ for a non-precision approach.
2. CNAF Absolute minimums for a single piloted fixed-wing aircraft when actually executing
an Instrument Approach Procedure ___________.
4. The NIFM (NATOPS Instrument Flight Manual) allows the use of GPS approaches for the
bases of alternate airport selection. (TRUE or FALSE)
6. Commercial airports where into-plane fuel contracts are in place, (DOD approved) the
name of the refueling agent are found at ___________________________________.
8. When rounding for fuel calculations any fraction over a ____ pound increment, rounds
____________________________________.
9. STTO fuel of 50 lbs is used for normal situation but should be adjusted if extended ground
delays are expected. (TRUE/FALSE)
11. The PCL climb distance is based on no-wind and should be corrected for actual
groundspeed. Determining the corrected Climb DIST will fix the point where calculations stop
using _____ groundspeed/fuel flow data and begin using _____ groundspeed/fuel flow data.
12. An EFR calculated for each leg on the Flight Log allows the pilot to check fuel usage
during the flight. Should AFR be lower than EFR at a given checkpoint, possible cause include;
____________________________________________________________,
___________________________________________________________________,
____________________________________________, _____________________or
_______________________________________.
13. CNAF fuel RESERVE requirements are _______% of the fuel required for Climb/Route
To Destination plus Route To Alternate plus Approaches, but will never be less than enough for
_______ minutes of flight time computed at _______________________ fuel flow at
_________________ feet. This reserve does not include addition reserves that may be required
to meet local SOP requirements.
1400. INTRODUCTION
The purpose of an IFR flight plan is to communicate the pilot’s desires to Air Traffic Control.
A VFR flight plan enables search and rescue agencies to identify overdue aircraft and to know
where to look for it. (This information, while required for IFR clearances may also aid IFR
aircraft when outside of radar control and/or in lost communication situations.)
“Except when a daily flight schedule is used in lieu of a flight plan form, the pilots in
command/formation leaders shall submit a flight plan for their flight (including remote filing via
the FWB system).”
AIM “Pilots should file IFR flight plans at least 30 minutes prior to estimated time of
departure to preclude possible delay in receiving a departure clearance from ATC.”
In order to provide FAA traffic management units strategic route planning capabilities,
nonscheduled operators conducting IFR operations above FL 230 are requested to voluntarily
file IFR flight plans at least 4 hours prior to estimated time of departure (ETD). To minimize
your delay in entering Class B, Class C, Class D, and Class E surface areas at destination when
IFR weather conditions exist or are forecast at that airport, an IFR flight plan should be filed
before departure. Otherwise, a 30 minute delay is not unusual in receiving an ATC clearance
because of time spent in processing flight plan data.
Chapter Four of the FLIP General Planning (GP) has block by block instructions for completion
of the DD Form 1801 (DoD Flight Plan).
The Aeronautical Information Manual (AIM) has block by block instructions for the FAA
FORM 7233-4 (International Flight Plan). This form may be used in lieu of DD Form 1801
when departing installations not having a military airfield management/base operations facility.
FLIP GP Chapter Four describes all items required to be completed by the pilot.
(See Figure 14-1)
Using the sample problem from Chapter Thirteen, the following example will cover each of the
items that require pilot action.
1. Item (7)
AIRCRAFT IDENTIFICATION:
TW5 FWOP: Approved Tactical call signs Inside local Area (180 NM from KNSE) and when
using stereo routes:
BB###
RN###
SH###
TEXN###
TW5 FWOP: Outside Local area (other than Stereo Routes) IAW guidance for Navy Training
Command Aircraft from GP Chapter 5:
GP Chapter Five provides some specific details concerning non-tactical codes to be used for
aircraft identification. Navy Fleet and Training command aircraft call signs will be:
Prefaced by the spoken word “NAVY” (written as VV) followed by a suffix of:
TW4 SOP: Following call signs SHALL be used for all VFR and IFR flights:
BOMR###
RNGR###
It is imperative that the call sign entered in the flight plan (Item 7) match exactly to what is
entered in the Mode S Aircraft Identification (MFD ROUTE menu under “Flight ID”). If it does
not, then the aircraft will not be correlated with its stored flight plan and delays will ensue.
2. Item (8)
FLIGHT RULES:
Y – If the flight initially will be operated under IFR followed by one or more subsequent changes
of flight rules
Z – If the flight initially will be operated under VFR followed by one or more subsequent
changes of flight rules If Y or Z is entered, specify in Item 15 where the Change of Flight
Rules is planned.
NOTE: US Domestic ATC systems cannot accept a flight plan that begins under VFR and
subsequently changes to one or more flight rules (that is, “Z”). For this purpose, file separate
flight plans for the portions of the route that the pilot intends to conduct under IFR for flights
solely in US Domestic Airspace. (FAA 7110.10AA Appendix A-4)
TYPE OF FLIGHT:
Enter one of the following letters to denote the type of flight when so required by the appropriate
Air Traffic Service authority.
G – General Aviation
M – Military
3. Item (9)
NUMBER and TYPE of AIRCRAFT: If one aircraft, indicate type only. If more than one,
insert number of aircraft.
TYPE OF AIRCRAFT: Enter military designator of aircraft omitting prefixes and suffixes
pertaining to aircraft mission or model.
If the flight consists of different types of aircraft in formation, use the 4 letter group “ZZZZ.” If
“ZZZZ” is used, the number and type of aircraft will be indicated in Item 18 preceded by the
abbreviation “TYP/” (e.g., TYP/2KC125-4F16).
The FIXED WING AIRCRAFT table in the GP, list the BEECH AIRCRAFT COMPANY
(USA) AT6, T-6 Texan 2 as having the type designation of TEX2.
WAKE TURBULENCE CATEGORY: Insert the letter code indicating the Wake Turbulence
Category (maximum certificated aircraft take-off weight) as follows:
4. Item (10)
Enter the letter “N” if no COM/NAV/Approach Aid equipment for the route to be flown is
carried, or the equipment is unserviceable and/or
Insert one or more of the following letters to indicate the COM/NAV/approach aid equipment
available, serviceable, will be used, and commensurate with flight crew qualifications:
A - GBAS landing system J1 - CPDLC ATN VDL Mode 2 (See Note 4) P1 - CPDLC RCP 400 (Note 8)
B - LPV (APV with SBAS) J2 - CPDLC FANS 1/A HFDL P2 - CPDLC RCP 240 (Note 8)
C - LORAN C J3 - CPDLC FANS 1/A VDL Mode A P3 - SATVOICE RCP 400 (Note 8)
D - DME J4 - CPDLC FANS 1/A VDL Mode 2 P4-P9 - Reserved for RCP
E1 - FMC WPR ACARS J5 - CPDLC FANS 1/A SATCOM (INMARSAT) R - PBN Approved (Note 5)
E2 - D-FIS ACARS J6 - CPDLC FANS 1/A SATCOM (MTSAT) T - TACAN
E3 - PDC ACARS J7 - CPDLC FANS 1/A SATCOM (Iridium) U - UHF RTF
F - ADF L - ILS V - VHF RTF
G - (GNSS) (See Note 3) M1 - ATC RTF SATCOM (INMARSAT) W - RVSM Approved
H - HF RTF M2 - ATC RTF (MTSAT) X - MNPS Approved
I - Inertial Navigation M3 - ATC RTF (Iridium) Y - VHF with 8.33 kHz CH spacing
O - VOR Z - Other equipment carried or other
capabilities (See Note 6)
If the aircraft is not FM immune, mark the DD1801, Block 10 with a Z and in Block 18 write
NAV/NON-FM IMMUNE VOR/ILS. Do not mark DD1801, Block 10, with S. (An S indicates
the aircraft VHF VOR/ILS nav receiver is FM immune compliant.) WARNING: This
information cannot be guaranteed to reach the destination approach controller. (See Note 2)
NOTE 1 - ATC issues clearances based on equipment qualifiers filed in item 10 and aircraft
capabilities filed in Item 18 (NAV/) of DD 1801.
NOTE 2 - If the letter “S” is used, standard equipment is considered to be VHF RTF, VOR, and
ILS unless another combination is prescribed by the appropriate ATS authority.
NOTE 3 - If the letter “G” is used, the types of external GNSS augmentation, if any, are
specified in Item 18 following the indicator NAV/ and separated by a space.
NOTE 5 - If the letter “R” is used, the performance based navigation levels that can be met are
specified in Item 18 following the indicator PBN/. Guidance material on the application of
performance based navigation to a specific route segment; route or area is contained in the
Performance Based Navigation Manual (Doc 9613).
NOTE 6 - If the letter "Z" is used, specify in Item 18 the other equipment carried or other
capabilities, preceded by COM/, NAV/and/or DAT/as appropriate. If aircraft is not FM immune,
include: NAV/NON-FM IMMUNE VOR/ILS.
NOTE 7 - Information on navigation capability is provided to ATC for clearance and routing
purposes.
Enter the letter “N” if no surveillance equipment for the route to be flown is carried or the
equipment is unserviceable and/or
SSR Mode S:
Note - Enhanced surveillance capability is the ability of the aircraft to downlink aircraft derived
data via a Mode S transponder.
ADS-B
B2 - ADS-B with dedicated 1090 MHz ADS-B “out” and “in” capability
ADS-C
5. Item (13)
DEPARTURE AIRPORT:
Enter the 4 letter ICAO ID of the departure aerodrome. If the LOCID contains a number, if no
LOCID is assigned, or if the LOCID is not known:
If the flight plan has been submitted during flight, enter "AFIL" in this item and enter "DEP" in
Item 18 followed by the 4 letter ICAO identifier or the name of the Air Traffic Service Unit from
which the supplementary data can be obtained.
TIME:
Enter the 4 digit estimated off-block time (EOBT), i.e., the estimated time at which the aircraft
will commence movement associated with departure.
For a Flight Plan received from an aircraft in flight, enter the actual or estimated time over the
first point of the route to which the Flight Plan applies.
6. Item (15)
CRUISING SPEED
INSERT the True Airspeed for the first or the whole cruising portion of the flight, in items of:
Mach number, when so prescribed by the appropriate ATS authority, to the nearest hundredth of
unit Mach, expressed as:
INSERT the planned cruising level for the first or the whole portion of the route to be flown, in
items of:
Standard Metric Level in tens of meters, (ICAO only) expressed as “S” followed by 4 figures
(e.g., S1130), or,
ROUTE:
b. If the airport of departure is located on the airway/route, enter the designation of the
first airway/route. If the airport is not on the airway/route, enter the code "DCT," the
point where the airway/route is joined and the airway/route designator.
c. Enter each point at which a Change of Speed or Level, a Change of Route and/or a
Change of Flight is planned to be initiated. Each of these points must be followed by
the designator of the next airway/route segment (even if the same as the previous one)
or by the code "DCT" if the flight to the next point will be off airways/route unless
both points are defined by geographical coordinates.
NOTE: When a transition is planned between a lower and upper Air Traffic Control route,
and the routes are oriented in the same direction, the point of transition need not be
inserted.
a. Enter points normally not more than 30 minutes flying time or 370 km (200 NM)
apart, including each point at which a Change of Speed or Level, a Change of
Track, or a Change of Flight Rules is planned to be initiated.
When required by the appropriate ATC authorities, define the track of flights
operating predominantly in an east-west direction between N70° and S70° by
reference to significant points formed by the intersections of half or whole degrees
of latitude with meridians spaced at intervals of 10 degrees of longitude. For
flights operating in areas outside those latitudes the tracks shall be defined by
significant points formed by the intersection of parallels of latitude with meridians
normally spaced at 20 degrees longitude. The distance between significant points
shall, as far as possible, not exceed one hour's flight time. Additional significant
points shall be established as deemed necessary. For flights operating
predominantly in a north-south direction, define tracks by reference to significant
points formed by the intersection of whole degrees of longitude with specified
parallels of latitude which are spaced at 5 degrees.
b. Enter "DCT" between successive points unless both points are defined by
geographical coordinates or by bearing and distance.
AIRWAY/ROUTE DESIGNATORS:
Use the coded designator (2 to 7 characters) assigned to the airway/route, e.g., B1, R14, UB10.
NOTE: ATC may assign routes that have not been named to aircraft in flight. These routes
begin with numbers, e.g., 2E11, 3E60, 5T20, etc. However, these routes should not be
filed in the initial flight plan as the center computers will not recognize routes
beginning with numbers and will reject flight plans filed with such routes.
The route/airway entered must begin with a LETTER, e.g., J174, V270, UP20, TL9, etc.
a. The coded designator (2 to 5 characters) assigned to the point, e.g., VH, GEO, and
WHITE.
For even degrees of latitude and longitude use 7 characters. Describe: latitude in 2
figures followed by an "N" or "S" longitude in 3 figures followed by an "E" or "W."
An entry must be made under the route of flight whenever a change to the cruising speed
(5% TAS or 0.01 MACH or more) or the cruising level is planned, the entry will consist of:
The point described (from Significant Points entry) followed by a "/" then, the cruising speed
planned from that point (from Cruising Speed entry), followed without a space by the cruising
level (4 characters) planned to be initiated from the point described (from Cruising Level entry).
An entry must be made for each point where a change of flight rules is planned to be initiated.
The entry consists of the description of the point (described from the Significant Points and
Change of Speed or level entries) followed with a space by:
"IFR" if the flight changes from VFR to IFR, e.g., VH/N0284A050 IFR.
NOTE: US Domestic ATC systems cannot accept a flight plan that begins under VFR and
subsequently changes to one or more flight rules. For this purpose, file a separate
flight plan for the IFR portion of the flight.
CRUISE CLIMB:
Enter the letter "C" followed by a "/"; then the point at which the cruise climb is planned to start
(described from Significant Points entry), followed by a "/"; then the speed to be maintained
during cruising climb (described from Cruising Speed entry), followed by the two levels defining
the layer to be occupied during cruise climb, each level (described from Cruising Level entry), or
the level above which cruise climb is planned, followed by the word "PLUS" without a space
between them, e.g.,
C/48N050W/M082F290F350 C/48N050W/M082F290PLUS
C/52N050W/M220F580F620
7. Item (16)
If the LOCID contains a number, no LOCID is assigned, or the LOCID is not known:
Insert “ZZZZ” in ITEM 16 and Provide destination airport information in ITEM 18 by inserting
“DEST/” followed by information below (in ITEM 18)
For all flights, insert the total estimated time (EET) to the destination.
For IFR flights, it is the estimated time required from takeoff to the initial approach fix (or other
defined point of interest, i.e. FIR boundary), or if there is no navigation aid associated with the
destination aerodrome, time to arrive over the destination aerodrome.
ALTERNATE AIRPORT(S) - Enter the 4 letter ICAO location identifier-(s) of not more than
two alternate airports, separated by a space.
If there is no assigned location identifier, enter "ZZZZ" and specify in Item 18 the name and
location of the aerodrome preceded by “ALTN/”.
Figure 14-9 DD 1801 Item 16 Dest Airport / Total EET / ALTN Airport(s)
8. Item (18)
OTHER INFORMATION:
Enter "0" (zero) if no other information is entered. Precede all information by one of the
following abbreviations and a "/" (abbreviations are listed in the required sequence):
STS/ Reason for special handling by ATS, e.g., a search and rescue mission, as follows:
ATFMX: for a flight approved for exemption from ATFM measures by the appropriate ATS
authority;
FFR: fire-fighting;
MARSA: for a flight for which a military entity assumes responsibility for separation of
military aircraft;
Other reasons for special handling by ATS shall be denoted under the designator RMK/.
PBN/ Indication of RNAV and/or RNP capabilities; This code Include as many of the descriptors
below, as apply to the flight, up to a maximum of 8 entries, i.e., a total of not more than 16
characters.
RNAV SPECIFICATIONS
A1 RNAV 10 (RNP 10)
B1 RNAV 5 all permitted sensors NATOPS
B2 RNAV 5 GNSS Oceanic/Remote
B3 RNAV 5 DME/DME
B4 RNAV 5 VOR/DME
B5 RNAV 5 INS or IRS
B6 RNAV 5 LORANC
C1 RNAV 2 all permitted sensors
C2 RNAV 2 GNSS US En Route Area
C3 RNAV 2 DME/DME Nav
C4 RNAV 2 DME/DME/IRU
D1 RNAV 1 all permitted sensors
D2 RNAV 1 GNSS US Terminal
D3 RNAV 1 DME/DME NAV /SID / STAR
D4 RNAV 1 DME/DME/IRU
RNP SPECIFICATIONS
L1 RNP 4
O1 Basic RNP 1 all permitted sensors
O2 Basic RNP 1 GNSS
O3 Basic RNP 1 DME/DME
O4 Basic RNP 1 DME/DME/IRU
S1 RNP APCH RNAV (GPS) Approach
S2 RNP APCH with BARO-VNAV
T1 RNP AR APCH with RF (special authorization required)
T2 RNP AR APCH without RF (special authorization required
PBN/B2C2D2S1
NAV/ Significant data related to navigation equipment, other than as specified in PBN/, as
required by the appropriate ATS authority.
Indicate GNSS augmentation under this indicator, with a space between two or more methods of
augmentation, e.g., NAV/GBAS SBAS.
While the T-6B does have WAAS (Wide Area Augmentation System) installed, it is for use
with ADS-B transmissions only and affords no additional aircraft navigation capabilities.
When Performance Based Navigation Capability has been filed in PBN/, if PBN routing is
desired for only some segment(s) of the flight then that information can be conveyed by inserting
the character “Z” in Item 10 and “NAV/RNV” in field 18 followed by the appropriate RNAV
accuracy value(s) per the following:
c. To be assigned enroute extensions and/or RNAV PTP, insert the characters “E2.”
COM/ Indicate communications applications or capabilities not specified in Item 10a, when
requested by an air navigation service provider.
DAT/ Indicate data applications or capabilities not specified in 10a, when requested by an air
navigation service provider.
SUR/ Include surveillance applications or capabilities not specified in Item 10b, when requested
by an air navigation service provider.
1. If ADS-B capability filed in Item 10 is compliant with RTCA DO-260B, include the item
“260B” in SUR/. If ADS-B capability filed in Item 10 is compliant with RTCA DO-282B,
include the item “282B” in SUR/.
2. When Required Surveillance Performance (RSP) Capability has been filed in SUR/, this
can be conveyed by inserting the character “Z” in Item 10 and “SUR/” in field 18 followed by
the appropriate RSP performance per the following:
DEP/ Name and location of departure aerodrome, if ZZZZ is inserted in Item 13. For
aerodromes not listed in the relevant Aeronautical Information Publication, indicate location as
follows:
With 4 figures describing latitude in degrees and tens and units of minutes followed by “N”
(North) or “S” (South), followed by 5 figures describing longitude in degrees and tens and units
of minutes, followed by “E” (East) or “W” (West). Make up the correct number of figures,
where necessary, by insertion of zeros, e.g., 4620N07805W (11 characters). OR,
The identification of the significant point followed by the bearing from the point in the form of 3
figures giving degrees magnetic, followed by the distance from the point in the form of 3 figures
expressing nautical miles. In areas of high latitude where it is determined by the appropriate
authority that reference to degrees magnetic is impractical, degrees true may be used. Make up
the correct number of figures, where necessary, by insertion of zeros, e.g., a point of 180°
magnetic at a distance of 40 nautical miles from VOR “DUB” should be expressed as
DUB180040. OR,
The first point of the route (name or LAT/LONG) or the marker radio beacon, if the aircraft has
not taken off from an aerodrome.
DEST/ Name and location of destination aerodrome if ZZZZ is inserted in Item 16. For
aerodromes not listed in the relevant Aeronautical Information Publication, indicate location in
LAT/LONG or bearing and distance from the nearest significant point, as described under DEP/
above.
DOF/ The date of flight departure in a six figure format (YYMMDD, where YY equals the year,
MM equals the month and DD equals the day).
REG/ The nationality or common mark and registration mark of the aircraft, if different from the
aircraft identification in Item 7.
EET/ Significant points or FIR boundary designators and accumulated estimated elapsed times
from take-off to such points or FIR boundaries, when so prescribed on the basis of regional air
navigation agreements, or by the appropriate ATS authority.
Examples:
SELCAL is a signaling method which can alert an individual aircraft that a ground station wishes
to communicate with it. SECAL codes are assigned to aircraft operators and not to individual
aircraft.
TYP/ Type(s) of aircraft, preceded if necessary without a space by number(s) of aircraft and
separated by one space, if ZZZZ is inserted in Item 9. Example: TYP/2F15 5F5 3B2
CODE/ Aircraft address (expressed in the form of an alphanumerical code of six hexadecimal
characters) when required by the appropriate ATS authority.
Example:
“F00001” is the lowest aircraft address contained in the specific block administered by ICAO.
DLE/ Enroute delay or holding, insert the significant point(s) on the route where a delay is
planned to occur, followed by the length of delay using four figure time in hours and minutes
(hhmm).
Example:
DLE/MDG0030
OPR/ ICAO designator or name of the aircraft operating agency, if different from the aircraft
identification in item 7.
Example:
OPR/DOD
ORGN/ The originator’s 8 letter AFTN address or other appropriate contact details, in cases
where the originator of the flight plan may not be readily identified, as required by the
appropriate ATS authority.
Note - In some areas, flight plan reception centers may insert the ORGN/ identifier and
originator’s AFTN address automatically.
PER/ Aircraft performance data, indicated by a single letter as specified in the Procedures for Air
Navigation Services — Aircraft Operations (PANS-OPS, Doc 8168), Volume I — Flight
Procedures, if so prescribed by the appropriate ATS authority.
ALTN/ Name of destination alternate aerodrome(s), if ZZZZ is inserted in Item 16. For
aerodromes not listed in the relevant Aeronautical Information Publication, indicate location in
LAT/LONG or bearing and distance from the nearest significant point, as described in DEP/
above.
RALT/ ICAO four letter indicator(s) for enroute alternate(s), as specified in Doc 7910, Location
Indicators, or name(s) of enroute alternate aerodrome(s), if no indicator is allocated. For
aerodromes not listed in the relevant Aeronautical Information Publication, indicate location in
LAT/LONG or bearing and distance from the nearest significant point, as described in DEP/
above.
TALT/ ICAO four letter indicator(s) for take-off alternate, as specified in Doc 7910, Location
Indicators, or name of take-off alternate aerodrome, if no indicator is allocated. For aerodromes
not listed in the relevant Aeronautical Information Publication, indicate location in LAT/LONG
or bearing and distance from the nearest significant point, as described in DEP/ above.
RIF/ The route details to the revised destination aerodrome, followed by the ICAO four-letter
location indicator of the aerodrome. The revised route is subject to re-clearance in flight.
Examples:
RMK/ Any other plain language remarks when required by the appropriate ATS authority or
deemed necessary.
b. For required call sign changes file - EXAMPLE: RMK/ Change call-sign to XXX
at position XXXX MDCN LG XXXX XXX LI XXXX LS X XXX XXX).
c. Pass DEP ARR to XXXXZPZX. (Replace "XXXX" with ICAO Identifier of aircraft
home station).
d. Hazardous Cargo Enter "Hazardous Cargo,” "Inert Devices" or both (as appropriate).
f. Flight Plan VIP codes for military bases only. See GP (FLIGHT PLAN VIP
CODES).
RMK/ Any other plain language remarks when required by the appropriate ATS authority or as
deemed necessary.
9. Item (19)
SUPPLEMENTARY INFORMATION:
FUEL/ - Enter "Total Fuel Endurance" in 4 figures expressed in hours and minutes.
RADIO - Cross out any "Portable Radio Frequencies" not carried as survival equipment.
LIFE JACKETS - Cross out "Jackets, Light Fluorescein" (sea marker dye), if life jackets are not
carried. Cross out "Light" or "Fluorescein" if jackets are not so equipped.
DINGHIES - Cross out if not carried. Cross out "Cover" if dinghies not covered. Identify
"Color and Number" if dinghies carried and indicate total "Capacity,” in persons carried, of all
dinghies.
OTHER EQUIPMENT- Indicate after "REM/" any other "Survival Equipment" carried and any
other remarks regarding Emergency and Survival Equipment.
FUEL/0239
RADIO - Cross out any "Portable Radio Frequencies" not carried as survival equipment.
LIFE JACKETS - Cross out "Jackets, Light Fluorescein" (sea marker dye), if life jackets are not
carried. Cross out "Light" or "Fluorescein" if jackets are not so equipped.
DINGHIES - Cross out if not carried. Cross out "Cover" if dinghies not covered. Identify
"Color and Number" if dinghies carried and indicate total "Capacity,” in persons carried, of all
dinghies.
OTHER EQUIPMENT - Indicate after "REM/" any other "Survival Equipment" carried and any
other remarks regarding Emergency and Survival Equipment.
REMARKS - This space will be used only for information for, or requests from, the departure
Base Operations.
For formation flights, enter Bureau Number/Serial Number and type of each aircraft.
Figure 14-22 DD 1801 Bottom Section Aircraft Serial Number and Type Of
Aircraft In Flight
United States Army, United States Air Force and CIVIL - No other entry is required.
In this example, the aircrew wishes to practice holding at OYSTY for 20 minutes prior
continuing on to TINEE.
In this example, upon reaching RAYOP the aircrew desires a practice IAP at KNEW prior to
continuing on to TINEE.
Use the DD Form 1801-C to file each leg after the initial leg of a stopover flight plan.
a. File the DD Form 1801-C for subsequent legs in conjunction with the DD Form 1801
used for the initial leg.
c. Complete DD Form 1801-C using the same guidance used to complete DD Form
1801.
d. Only use Block 18. OTHER INFORMATION when there are changes from the
information entered on the DD Form 1801 filed for the initial leg.
e. Block 19 Supplemental Information: Include new fuel endurance for this leg and
number of souls onboard.
f. This example shows a continuing flight on to KGPT after our mission to KNBG.
FAA Form 7233-4 may be used in lieu of DD Form 1801 when departing United States
Installations not having a Military Base Operations.
1. IFR flight plans should be filed at least _______ minutes prior to the estimated time of
departure to preclude possible delays in receiving a departure clearance for ATC.
2. Detailed instructions for completing a military flight plan are found in chapter ____ of the
publication.
3. The Item 10 Equipment code for the T-6B with ADS-B is ____________________.
4. If you intend to cruise at 17,000 feet MSL you would enter ___________ in Item 15 for
LEVEL. For an altitude of 22,000 feet MSL you would enter ___________.
5. The first entry for Item 15: Route will always be DCT. (TRUE/FALSE)
6. The time entered in Item 16 TOTAL EET includes all planned holding and terminal delays
along the way to your destination. (TRUE/FALSE)
7. Based on the flight log provided below, your entry for Item 19 ENDURANCE FUEL/
would be ___________.
8. Based on the flight log above, your entry for Item 15 ROUTE should read:
____________________________________________________________
9. Based on the flight log above, if you desire to hold enroute at TBD for 20 minutes and then
continue on, your Item 15 ROUTE should read:
___________________________________________________________
10. What supporting entry(s) for Item 18 OTHER INFORMATION would be used to clarify
your intentions based on question 10 above? ______________________________________
11. You require the following types of information to be listed for Item 18 OTHER
INFORMATION. List them in the correct sequence in which they should appear: OPR/ RMK/
PBN/ DLE/ DOF/ DEST/ REG/.
______________________________________________________________________________
12. The Performance Based Navigation code (PBN/) for the T-6B is __________.
1500. INTRODUCTION
Due to the constant changes that occur in flight planning publications key information has been
provided for each problem. Use of current publications may not match the intended outcomes
for this exercise.
Directions:
Direct distances on Enroute High and Low Charts provided can be obtained using
https://skyvector.com.
Use Courses and distances when depicted on provided Charts (sky vector web site will be
slightly different for these values).
Route: Depart Orlando Intl, RWY 35L at 1000 local time via CITRUS SEVEN DEPARTURE
to Orlando VORTAC, direct Lakeland VORTAC, direct LEE CO, J41 to KEY WEST direct
SKIPP for the VOR/DME or TACAN Z RWY 8 APPROACH.
Route to ALTN 1: Direct KEY WEST then the DVALL TWO ARRIVAL KEY WEST
Transition direct DOLPHIN, direct GLRIA for the ILS or LOC RWY 12
Route to ALTN 2: Direct KEY WEST J41 LEE CO direct to FIVER for the VOR RWY 13
NOTAMs: KFMY: QNDAC
Route to ALTN 3: Direct KEY WEST then the DVALL TWO ARRIVAL KEY WEST
Transition. Direct DOLPHIN direct LAYDN for the ILS or LOC RWY 9R
Climb Data:
Cruise Data:
Fuel Data:
STTO 50 lbs
Approach 50 lbs
Additional Data:
6. KMCO SID
7. KMCO APPROACH
1. Only one of the Alternate airport options was viable. List the airports that were not
acceptable and the reason(s) why they could not be used as an alternate.
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
2. If you require fuel at KMCO you can call ______________ via phone on ___________.
3. On departure from KMCO via the CITRUS SEVEN DEPARTURE you will maintain
________ feet and expect further clearance to ________________ 10 minutes after departure.
4. The CNAF minimum RVR needed for takeoff on runway 35L at KMCO is_______.
8. Aircraft shall not fly over the city of Key West below _______ feet unless under radar
control or executing an approved instrument approach.
9. Noise Abatement is in effect at KTMB. Details can be obtained from ___________ via
phone number _______________________.
10. The traffic pattern for high performance aircraft on runway 9R/27L at KTMB is
________feet.
Route to DEST: Depart CAIRNS AAF at 0800L via the OPPTO TWO DEPARTURE
CRESTVIEW Transition V198 INBRD direct to MERTY for an ILS approach to RWY 14
Route to ALTN 1: Direct to INBRD V198 to CEW for the ILS approach to RWY 17
Route to ALTN 2: Direct SAUFLEY VOR for the VOR RWY 19 circle to land RWY 7L
Route to ALTN 3: Direct to INBRD V198 to ITNEW for the VOR/DME RWY 30
Climb Data:
Cruise Data:
Fuel Data:
STTO 50 lbs
Approach 50 lbs
Additional data:
1. Only one of the Alternate airports options was viable. List the airports that were not
acceptable and the reason(s) why they could not be used as an alternate.
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
5. If the approach lighting for runway 6 at KOZR was inoperative, how would it affect the
takeoff minimums? ____________________________________________________________.
6. On departure from KOZR via the OPPTO-TWO DEPARTURE you are expected to
maintain _______ feet and expect clearance to requested altitude/Flight Level ____ minutes after
departure.
7. KOZR can be found on the IFR Low Altitude Chart ____ on Panel ___.
Route to DEST: Depart CORPUS CHRISTI NAS RWY 31L AT 1000L VIA RADAR
DEPARTURE TO the CORPUS CHRISTI then via the TCHDN TWO ARRIVAL CORPUS
CHRISTI TRANSITION for radar vector to final for the HI ILS or LOC/DME RWY 35L
Route to ALTN 1: Direct to HOBBY direct ALIBI for a LOC RWY 14 APPROACH
Route to ALTN 2: Direct to HOBBY direct KILSE for the RNAC (GPS) RWY 34
Route to ALTN 3: Direct to HOBBY then J37 to HEIGH direct BPT for the ILS or LOC
RWY 12
Climb Data:
Cruise Data:
Fuel Data:
STTO 50 lbs
Approach 50 lbs
Additional Data:
16. Brenham Muni FAA Chart Supplements Information (Airport not listed in
IFR Supplement)
17. BRENHAM MUNI APPROACH (Only two approaches available both RNAV (GPS)
type)
1. Only one of the Alternate airports options was viable. List the airports that were not
acceptable and the reason(s) why they could not be used as an alternate.
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
3. Why was the PAR RWY 31L not used to determine CNAF Takeoff Minimums from
KNGP? ______________________________________________________________________.
6. Why can you not plan on using the KEFD ILS RWY 35L approach if you were to arrive
earlier than 0930L? ____________________________________________________________.
7. What is the emergency safe altitude for area within 100 NM of the ELLINGTON TACAN
(EFD)? ______________.
8. Is there and approach lighting system for KBPT runway 12. If so, what type is it?
_____________________________________________________________________________.
9. What would be the implications if local weather was not available at KBPT?
_____________________________________________________________________________.
10. What is the minimum safe altitude within 25 NM of runway 34 at K11R? _____________.
All page numbers shown are approximate and may vary based on the publication date.
4. Approach control radar used to detect and display an aircraft position in the terminal area.
(GP 2-5)
5. A maneuver initiated by the pilot to align the aircraft with a runway for landing when a
straight-in landing from an instrument approach is not possible or desirable. (GP 2-11)
6. V4 (GP 4-1/2)
All page numbers shown are approximate and may vary based on the publication date.
4. Two way radio, Transponder (Mode 3/A or C with 4096 codes,) (AP/1 3-58)
8. 1200’above the surface, to but not including 18,000’ MSL, LOW (AP/1 3-58)
11. Two way radio, VOR or TACAN or RNAV, Transponder (4096 codes, mode 3/A/C)
(AP/1 3-59)
14. Two way radio, Transponder 4096 codes mode 3/A/C (AP/1 3-58)
All page numbers shown are approximate and may vary based on the publication date.
7. The second Sunday in March, the first Sunday in November (IFR SUP A-9)
11. Bi-directional (Hook engaged type E28), 1200’ (IFR SUP B-514)
12. PPR (this is like a reservation #), call 928-269-2445/2760/ (IFR SUP B-732)
19. 119.725 (high Altitude), 126.8 (Low Altitude) (IFR SUP A-29 and B-305)
2. Yes, In either the DoD FLIP or FAA Terminal Procedure Publication (TPP).
3. No
4. Minimum Enroute Altitude (MEA) - The lowest published altitude between radio fixes
which assures acceptable navigational signal coverage and meets obstacle clearance requirements
between those fixes. The MEA prescribed for a Federal airway or segment thereof, area
navigation low or high route or other direct route applies to the entire width of the airway,
segment or route between the radio fixes defining the airway, segment, or route.
7. Minimum Reception Altitude (MRA) - (P/CG, Pilot to Controller Glossary): The lowest
altitude at which an intersection can be determined. (JCS, Joint PUB 1-02, the DoD
dictionary of Military and associated terms): The lowest altitude required to receive adequate
signals to determine the specific VHF omnirange (VOR)/tactical air (TACAN) fixes.
8. Minimum Crossing Altitude (MCA) - The lowest altitude at certain radio fixes at which
an aircraft must cross when proceeding in the direction of a higher MEA.
9. 111 NM
10. 50 NM
12. No
13. It is the VHF frequency that is paired with KEESLERS TACAN Channel 55. If this
frequency is tuned in the T-6B VHF NAV you will receive DME from the TACAN channel if
within range.
14. ANNISTON
15. 122.2 or 255.4 (for normal communications) and emergency frequencies of 121.5
or 243.0
1. 59 NM from NORTHBROOK
2. VOR/DME
3. OBK
5. 23.5 NM (Midpoint)
6. RNAV Route
8. The Maximum Authorized Altitude for that section (only shown when other than
45,0000)
14. Yes
16. 082°
18. False
19. No
All page numbers shown are approximate and may vary based on the publication date.
8. – When vacating any previously assigned altitude or flight level for a newly assigned
altitude or flight level.
– Change in average true airspeed (at cruising altitude) when it varies by 5 percent or
10 knots (whichever is greater) from that filed on the flight plan.
– The time and altitude or flight level upon reaching a holding fix or point to which
cleared.
– Any loss, in controlled airspace, of VOR, TACAN, ADF, low frequency navigation
receiver capability, complete or partial loss of ILS receiver capability or impairment
of air/ground communications capability.
10. Update the Flight Weather Briefing form DD-175-1, to receive pilot weather reports
(PIREPS) of significant or hazardous weather phenomena. (FIH pg. C-15)
16. Inflight when requested, when unusual and un-forecast weather conditions are encountered,
When weather conditions on an IFR approach differ from the latest observation, When a missed
approach is executed due to weather, When wind shear is encountered on departure or arrival.
(FIH pg. C-66)
26. The facility or service reported upon, its status of operation, Instrument Landing System
(ILS) Withdrawn for maintenance (FIH pg. F-32,35,38)
1. GTR
4. 111.15
5. 002°
6. 8003 feet
7. 264 feet
9. HANOP
16. 3°, 42
17. BAWMO
19. 200, ¾
21. 5.4 NM
22. FALSE (It is a Medium Intensity Approach Lighting System with Runway alignment
indicator lights)
23. FALSE
4. Departure airport, Destination airport, Alternate airport, Route of flight, ARTTCs along
the route of flight, TFRs (Temporary Flight Restrictions)
5. 1-800-WX-BRIEF
8. DAIP
1. TRUE
3. 1-888-PILOTWX
4. 1-800-WX-BRIEF
5. Storm development has not progressed as forecast for the planned route as verified by
DoD forecasters or an FSS and VMC can be maintained, thus enabling the aircraft to detect
and avoid isolated thunderstorms.
8. 140, 10
11. 29.96
12. 19° C
13. 19° C
15. 400-3/4
16. 300-3/4
17. 500-1 ¼
18. 700-1 ¾
19. – The actual weather at the point of departure at the time of clearance.
– The existing and forecasted weather for the entire route of flight.
– Destination and alternate forecast for a period 1 hour before ETA until 1 hour after
ETA
21. http://www.aviationweather.gov
24. Altimeter setting, wind data, temperature, dew point, density altitude, visibility, and
cloud/ceiling data.
2. (200-1/2 or 200/24)
3. (PAR/ASR)
4. (FALSE)
5. (0200 local time on the second Sunday in March, 0200 local time the first Sunday in
November)
7. (140)
9. (TRUE)
12. (Less fuel onboard at takeoff than planned, higher fuel flow in Climb/Cruise than
planned, slower groundspeed than planned, bad math, a fuel leak)
1. (30)
3. (DIYRUGS/LB1)
4. (170, FL220)
5. (FALSE)
6. (TRUE)
7. (0233)
12. (PBN/B2C2D2S1)
1. KFMY, DME out of service and is required for the available approach. KTBM,
ALTERNATE NA due to tower being closed (NOTAM)
4. 2400
5. Tethered Aerostat Radar System (TARS), a large helium balloon type device operating
continuously up to 14,000 feet. It has strobe lights on the balloon, but the tether is unmarked
and nearly impossible to see.
7. ATIS 307.025
8. 3000 feet
2. An aircrew member must remain with the aircraft during refueling operations.
3. At the field
4. 75’ trees left and right of centerline on the departure end of the runway
6. 2000, 10
7. L-22 panel I
8. 8.6 NM
10. FALSE
1. KCXO, Alternate NA symbol on the approach plate. K11R, Only GPS approaches are
available. GPS approaches not allowed for selection of alternate airports.
4. Air National Guard, Coast Guard, NASA, and Army National Guard
5. FALSE
7. 16,000 feet
8. Pilot Controlled MALSR (Medium Intensity Approach Lighting System with Runway
Alignment Indicator lights)
9. It would be ALTERNATE NA
B100. FORMS
FORMS B-1
APPENDIX B T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
B-2 FORMS
T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK APPENDIX B
FORMS B-3
APPENDIX B T-6B INSTRUMENT FLIGHT PLANNING WORKBOOK
B-4 FORMS