Dumbwaiter Brochure

Servicelifts
Goods only lifts

SKG-Doku.-Nr.: D-230004E
ISO A - Bi-parting doors on serving height ISO C - Bi-parting doors serving at floor level ISO D - Hinged doors serving at floor level
Capacity Speed cabin dimensions Shaft dims Headroom Serv.height Capacity Speed Cabin dimensions Shaft dims Headroom Pit Capacity Speed Cabin dimensions Shaft dims Headroom Pit
increments 50 mm increments 50 mm increments 50 mm
50 - 100 0,4 m/s Width 400 -1000 + 300 Serv.height min. 700 50 - 100 0,27 m/s Width 400 - 1000 + 350 Door height min. 1/2 DH + 50 50 - 100 0,27 m/s Width 400 - 1000 + 350 Door height min. 350
Depth 500 - 1000 + 150 + door height lowest floor Depth 600 - 1000 + 150 + 1260 mm Depth 600 - 1000 + 150 + 1260 mm
Height 600 - 1200 + 1260 1/2 door height + 50 Height 800 - 1200 Height 800 - 1200
150 - 300 0,25 m/s Width 500 - 1000 + 300 Serv. height min. 700 150 - 300 0,25 m/s Width 500 - 1000 + 350 Door height min. 1/2 DH + 50 150 - 300 0,25 m/s Width 500 - 1000 + 350 Door height min. 350
Depth 600 - 1000 + 150 + door height lowest floor Depth 600 - 1000 + 150 + 1360 mm Depth 600 - 1000 + 150 + 1360 mm
Height 600 - 1200 + 1360 1/2 door height + 50 Height 800 - 1200 Height 800 - 1200
ATTENTION: ATTENTION: ATTENTION:

On cabin protection clear entrance dimensions resp. shaft dimensions will change On cabin protection clear entrance dimensions resp. shaft dims will change. On cabin protection clear entrance dimensions resp. shaft dims will change.
Minimum floor to floor height on doors in line = 2 x door height + 290 mm Minimum floor to floor height on doors in line = 2 x door height + 290 mm
ISO - Servicelifts in special designs
Also available beside the shown proved types on left side
ISO - A, ISO - C, ISO - D
special designs for all clients requirements in compliance
with local national regulations.
Drive units not on top ■ If no sufficient space in headroom, drive unit can be positioned
above or below at side of the shaft.
Adjacent entrances ■ 2 or 3 sides available
Safety gear ■ Requested on shafts with space underneath
Ship lifts ■ with safety gear and controller in compliance to Lloyds rules and
regulations
Undercounter lifts ■ for installation in kitchens under a counter with a min.

installation height
Explosion proof ■ Available on request on chemical industry, paint stocks or mills
500 kg capacity ■ Goods lifts for pallet transport - available up to cabin

sizes of 1400 x 1400 x 2000 mm (wxdxh)
Goods lifts ISO - 500

with full galvanized
cladding and manual
lattice gate for
cabin protection
ISO-MAX 500/750/1000
The ISO-MAX is a goods only lift with two fixed cabin areas
of 1,00 x 1,40 m (capacity 300, 500, 750 and 1000 kg) or
1,275 x 1,50 m (Capacity 750 and 1000 kg) and a variable
cabin height from 1,20 – 2,00 m. Lift unit complies to EU-
Directive for machines and has a EU-Declaration of
conformity of German TÜV Hanover / Sachsen-Anhalt e.V.
ISO-MAX PM 1000
With passenger transport complies to 95/16 EG
(appropriable cabin depth up to 1,70 m)
Doors for
lift car
1,275 m
wide
as double
Car and doors galvanized steel hinged
doors
Cabin from 1,20 to 2,00 m

with passenger transport 1,80 – 2,0 m
(in 100 mm increments)
80 % pre-assembled
50 % saving in labour costs

compared to hydraulic lifts
galvanized self supporting

Loading
structure with
trolleys
Metal sheet-cladding available

(Capacity 750 and 1000 kg),
no separate machine-room
No brickwork required, savings in

construction at least 4000 Euro
Pit only 270 mm deep

Highest
safety
standard,
each
cabin with
Accessible space underneath the electronic
shaft is permitted overload
device
ISO-MAX 750/1000 KG
Hinged doors
Loading front and rear
Machine above
With safety gear
Well dimensions are absolute min. plumbed dimensions
Machine room access
Shaft floor to be constructed in accordance to layout drawing

Type 1 Type 2
CW = Car width 1000 mm 1275 mm
CD = Car depth 1400 mm 1500 mm
CH = Car height min.1200 - max. 2000 mm
DW = Door width Cabin width
DH = Door height Cabin height
P = Pit min. 270 mm
SW = Shaft width plumbed min. dimension ATTENTION:
SD = Shaft depth plumbed min. dimension Cabin protection reduces
HR = headroom Height of top floor FFL to ceiling clear entrance openings
FFL= finished floor level resp. shaft dimensions!
Standard equipment at no extra charge
STEEL STRUCTURE
Galvanized steel structure made of
cold rolled special profiles, premounted
in 2-m-sections incl. trunking
CABIN
made of folded galvanized steel sheets,
centered suspension, guided on both
sides with adjustable guide shoes.
All units serving on counter height
are to be supplied with a removable
shelf included. Increments of 50 mm available.
LANDING DOORS
Approved to DIN 18092 resp.
18090 as a bi-parting, single or double
hinged type available. Approved
door locks. Bi-parting doors suspended
with 2 high flexible steel ropes, guided
with aluminium sheaves in cage.
All doors with pre-installed frame
surrounds for easy installation.
MACHINE ROOM DOOR
Single hinged door, double hinged
for width over 800 mm
galvanized finish, with lock,
incl. frame surrounds.
COUNTERWEIGHT
Steel frame with 50 x 50 mm
steel inserts. Adjustable guide
shoes with polyamid inserts.
DRIVE UNIT
Up to 100 kg capacity with sheave
drive for 2 or 3 ropes. Units with 200
and 300 kg capacity with chain drive for
2 chains. High quality reduction gear
with motor, magnetic disc brake and
handwheel. Insulation class IP 54.
CONTROL
● 24 Volt system on all push button
units
● prewired and plug-in-system
● Call and send on each landing
station
● Despatching delay device
● Arrival buzzer and call signal
● Position indicator on each landing
station
● Overload protection inst. on control
panel
SPECIAL
160 options available
Our servicelift are available in full compliance
to BS 5655 Part III and further national
regulations.
SKG-Doku.-Nr.: D-230004E

Dumbwaiter Brochure

Uploaded by

Copyright:

Available Formats

Dumbwaiter Brochure

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Dumbwaiter Brochure

Uploaded by

Copyright:

Available Formats

Servicelifts

Goods only lifts

ATTENTION: ATTENTION: ATTENTION:

Adjacent entrances ■ 2 or 3 sides available

Safety gear ■ Requested on shafts with space underneath

Undercounter lifts ■ for installation in kitchens under a counter with a min.

Explosion proof ■ Available on request on chemical industry, paint stocks or mills

500 kg capacity ■ Goods lifts for pallet transport - available up to cabin

Goods lifts ISO - 500

Cabin from 1,20 to 2,00 m

50 % saving in labour costs

galvanized self supporting

Metal sheet-cladding available

No brickwork required, savings in

Pit only 270 mm deep

Well dimensions are absolute min. plumbed dimensions

Machine room access

Shaft floor to be constructed in accordance to layout drawing

You might also like