Math 11 2nd Grading

GOMA NATIONAL HIGH SCHOOL
School ID: 301906

Sitio Napan, Brgy. Goma, Digos City
Name: ________________________________Section:___________________ Oct. ____, 2018/SCORE:______
GRADE 12- TVL SMAW

SECOND QUARTER EXAMINATION
MULTIPLE CHOICE. Shade the circle of the letter of the best answer.
1 is a method of joining two metals by applying heat to melt and fuse them, producing a
coalescence of materials with or without the use of filler metal.
Ⓐ Ⓑ Ⓒ Ⓓ a. Fushion welding c. Gmaw
b. . welding d. Oxy-acetylene process
2 is a metal rod coated with a special substance called flux, which determines the nature
of the electrode. During welding it is melted to fill up joints in the base metal.
Ⓐ Ⓑ Ⓒ Ⓓ a. Bare electrode c. flux
b. Flux coated electrode d. electrode angle

3. a filler metal electrode used in arc welding, consisting of a metal wire with no coating
on its surface.
a. Bare electrode c. coated
Ⓐ Ⓑ Ⓒ Ⓓ
b. Coated electrode d. electrode coated
4. 4. is a fusible material or gas used to dissolve and/or prevent the formation of oxides,
nitrides or other undesirable inclusions formed in welding.
Ⓐ Ⓑ Ⓒ Ⓓ a. Weldment c. weld bead
b. Face of the weld d. flux

5. 5. The metal that is to be welded or worked.
a. Core metal c. metallic
Ⓐ Ⓑ Ⓒ Ⓓ
b. Parent or base metal d. circle metal
6. an assembly or structure whose component parts are joined by welding.

a. Weld bead c. weld face
Ⓐ Ⓑ Ⓒ Ⓓ
b. Weld ment d. weld root
7. it is a deposit of filler metal from a single welding pass
Ⓐ Ⓑ Ⓒ Ⓓ
8. a type of weld bead with appreciable transverse oscillation or side to side movement.
a. Figure of 8 c. linear motion
Ⓐ Ⓑ Ⓒ Ⓓ
b. Cresent motion d. stringer bead motion
9. expose surface of the weld.
Ⓐ Ⓑ Ⓒ Ⓓ a. Face of a Weld c. ripple
b. Crater d. pass
10. it is an angle from the electrode which is perpendicular to the base metal.
a. arc length c. type of electrode
Ⓐ Ⓑ Ⓒ Ⓓ
b. electrode angle d. arc angle
11. What method in striking an arc is recommended for the beginners?

a. Tapping method
b. Scratching method
Ⓐ Ⓑ Ⓒ Ⓓ c. Any of these
d. None of the above
Ⓐ Ⓑ Ⓒ Ⓓ 12. . In the symbol E-6013; letter “E” stands for:

a.Electric
b.Energy
c.Electrode
d.None of the above
13. Eyes can be protected during welding operations by using:
a. Gloves
b. Leggings
Ⓐ Ⓑ Ⓒ Ⓓ c. Goggles
d. Apron
14. It is done by touching the electrode to the base metal like scratching a match.
a. Tapping Method
Ⓐ Ⓑ Ⓒ Ⓓ b. Scratching Method
c. All of these
d. None of there
15. It is done by moving the electrode downward until it steps to the base metal and then
bringing the electrode up slightly to form an arc.
a. Taping Method
Ⓐ Ⓑ Ⓒ Ⓓ b. Scratching Method
c. All of these
d. none of these
16. 16. None of these The coating of electrode is sometimes called:
a. Flux
Ⓐ Ⓑ Ⓒ Ⓓ b. Shield
c. Covering
d. All of these
17. The electrode which has no coating is called:
a.Shielded
b.Bare
Ⓐ Ⓑ Ⓒ Ⓓ c. Dusted
d. Dipped
18. The symbol E-6013;60 means

a. Welding Position
b. Tensile Strength
Ⓐ Ⓑ Ⓒ Ⓓ c. Power Supply
d. Flux Coating
19. The third digit in the symbol E-6013; 1 stands for

a. Welding Position
Ⓐ Ⓑ Ⓒ Ⓓ b. Tensile Strength
c. Power Supply
d. Flux Coating
20 The diameter of the electrode to be used in welding operation depends upon the:
a. Thickness of the Base Metal
Ⓐ Ⓑ Ⓒ Ⓓ b. Welding Position
c. Type of Base Metal
d. None of these
21. Tack welds are simply short sections of weld beads measured?
.
a. 1/4” to ½”
Ⓐ Ⓑ Ⓒ Ⓓ c. ½” to !/4”
b.1” to 2 “
d. 3/8” to 5/8”
22. Type of tack weld measured at about ¼” up to ½” length. It is used fir up temporarily the
two pieces of heavy metal being joined
Ⓐ Ⓑ Ⓒ Ⓓ a. Permanent Tacking c. Semi-permanent Tacking
b.Bridge Tacking d. Semi Tacking
23. When two plates are joint, the following gap must be considered in performing tack
Ⓐ Ⓑ Ⓒ Ⓓ welding?
a. 8 mm c. 4 mm b. 3 mm d. 2 cm
24. What method of weld tacking usiusesiffeners or backing plate to keep both plates aligned?
Ⓐ Ⓑ Ⓒ Ⓓ a. Permanent Tacking c. Semi-permanent Tacking
b.Bridge Tacking d. Semi Tacking
Ⓐ Ⓑ Ⓒ Ⓓ 25. A tack weld done only in a very short bead. It is used to fit up temporarily the two light
pieces of metal to be joined.
a. Permanent Tacking c. Semi-permanent Tacking
b. Bridge Tacking d. Semi Tacking
26 It is the area where filler metal intersects the base metal opposite face.
Ⓐ Ⓑ Ⓒ Ⓓ a. Weld toe c. Weld root
b. Weld leg d. Weld face
27. It is the surface of the base metal that melts during welding.
a. Fusion welding c. Fusion face
Ⓐ Ⓑ Ⓒ Ⓓ b.Weld root d. Weld Toe
28. . It is the shortest distance from the face of a fillet weld to the weld root aft welding.
a.Actual Throat c. Theoretical Throat
Ⓐ Ⓑ Ⓒ Ⓓ b.Effective Throat d. Weld Toe
It is the work angle used for thin metal welded to thick metal plate fillet weld.
Ⓐ Ⓑ Ⓒ Ⓓ a. 40 degrees c. 45 degree
b. 55 degrees d. 60 degree
30 A fillet weld is a weld type in the cross-sectional shape of
Ⓐ Ⓑ Ⓒ Ⓓ a. Square c. Circle
b. Rectangle d. Triangle
31.What is the correct root gap between two plates?
a. a. 1.0mm c. 3.2mm
Ⓐ Ⓑ Ⓒ Ⓓ b. b. 4.0mm d. 5.0mm
32. What electrode number used to weld on root pass?

Ⓐ Ⓑ Ⓒ Ⓓ a. 6011 c. 6013
b. b. 7018 d. 7024
33. What electrode number is used to weld on the hot pass?
Ⓐ Ⓑ Ⓒ Ⓓ a. 6010 c.6012
b. 7018 d. 6011
34. What is the ideal arc length of electrode to the base metal?
Ⓐ Ⓑ Ⓒ Ⓓ a. 4.2mm c. 2.0mm
b. 1.2mm d. 3.2mm
35. What is the angle at which a bevel is cut?
Ⓐ Ⓑ Ⓒ Ⓓ a. Bevel c. Right angle
b. Bevel angle d. groove angle
36. Why is a surfacing weld different from the other weld types?
a. Because it does not join to distinct parts, but instead adds only filler metal to a
surface.
b. Because the heat is concentrated in a small region for greatest efficiency and
Ⓐ Ⓑ Ⓒ Ⓓ minimum metallurgical damage.
c. reconditioning temperatures for electrodes are higher than the storage
temperature, which helps eliminate excess moisture
d. welding arc, they release shielding gas to protect the molten weld pool from
atmospheric impurities.
37 Groove welds are most closely associated with which one of the following joint types:
Ⓐ Ⓑ Ⓒ Ⓓ a . butt, b.corner, c. edge, d. lap,
38. A fillet weld can be used to join which of the following joint types
Ⓐ Ⓑ Ⓒ Ⓓ a. butt, b. corner, c. edge, d. lap,
39 Prepare sketches showing how the part edges would be prepared and aligned with each
other and also showing the weld cross section for the following welds:
a.square groove weld, both sides, for butt weld and
Ⓐ Ⓑ Ⓒ Ⓓ b.single fillet weld for a lap joint.
c. single fillet weld for tee joint;
d. double U-groove weld for a butt weld.
40. A heat source can transfer 3500 J/sec to a metal part surface. The heated area is circular,
and theheat intensity decreases as the radius increases, as follows: 70% of the heat is
concentrated in acircular area that is 3.75 mm in diameter. Is the resulting power density
enough to melt metal?
Ⓐ Ⓑ Ⓒ Ⓓ a.225 W
b.224W
c. 222 W
d. 283 W
Ⓐ Ⓑ Ⓒ Ⓓ
Answer key:
1. B 21.C
2. B 22.C
3. A 23.C
4. D 24.B
5. B 25.C
6. B 26.C
7. A 27.C
8. D 28.A
9. A 29.C
10.B 30.D
11. B 31.C
12. C 32.A
13. C 33.B
14. B 34.D
15.A 35.B
16.D 36.A
17.B 37.A
18.B 38.B
19.A 39. A
20. A 40. C

Math 11 2nd Grading

Uploaded by

Copyright:

Available Formats

Math 11 2nd Grading

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Math 11 2nd Grading

Uploaded by

Copyright:

Available Formats

GOMA NATIONAL HIGH SCHOOL

School ID: 301906

Name: ____________________Section:_ Oct. , 2018/SCORE:

GRADE 12- TVL SMAW

b. Flux coated electrode d. electrode angle

b. Face of the weld d. flux

6. an assembly or structure whose component parts are joined by welding.

11. What method in striking an arc is recommended for the beginners?

Ⓐ Ⓑ Ⓒ Ⓓ 12. . In the symbol E-6013; letter “E” stands for:

18. The symbol E-6013;60 means

19. The third digit in the symbol E-6013; 1 stands for

32. What electrode number used to weld on root pass?

You might also like