Issued Date: 04, Mar 2008 Model No.

: V260B1 L11

Approval

TFT LCD Approval Specification MODEL NO.: V260B1 L11

Customer: Approved by: Note:

Approved By

TV Head Division LY Chen QA Dept. Tomy Chen Product Development Div. WT Lin

Reviewed By

Prepared By

LCD TV Marketing and Product Management Div. WY Li Delia Lin

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval
3 4

REVISION HISTORY 1. GENERAL DESCRIPTION 1.1 OVERVIEW 1.2 FEATURES 1.3 APPLICATION 1.4 GENERAL SPECIFICATIONS 1.5 MECHANICAL SPECIFICATIONS

- CONTENTS -

-------------------------------------------------------------------------------------------------------------

2. ABSOLUTE MAXIMUM RATINGS 2.1 ABSOLUTE RATINGS OF ENVIRONMENT 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2.1 TFT LCD MODULE 2.2.2 BACKLIGHT UNIT

-------------------------------------------------------

3. ELECTRICAL CHARACTERISTICS ------------------------------------------------------3.1 TFT LCD MODULE 3.2 BACKLIGHT INVERTER UNIT 3.2.1 CCFL(Cold Cathode Fluorescent Lamp) CHARACTERISTICS 3.2.2 INVERTER CHARACTERISTICS 3.2.3 INVERTER INTERTFACE CHARACTERISTICS 4. BLOCK DIAGRAM 4.1 TFT LCD MODULE 5. INTERFACE PIN CONNECTION 5.1 TFT LCD MODULE 5.2 BACKLIGHT UNIT 5.3 INVERTER UNIT 5.4 BLOCK DIAGRAM OF INTERFACE 5.5 LVDS INTERFACE 5.6 COLOR DATA INPUT ASSIGNMENT 6. INTERFACE TIMING 6.1 INPUT SIGNAL TIMING SPECIFICATIONS 6.2 POWER ON/OFF SEQUENCE 7. OPTICAL CHARACTERISTICS 7.1 TEST CONDITIONS 7.2 OPTICAL SPECIFICATIONS 8. DEFINITION OF LABELS 8.1 CMO MODULE LABEL 9. PACKAGING 9.1 PACKING SPECIFICATIONS 9.2 PACKING METHOD 10. PRECAUTIONS 10.1 ASSEMBLY AND HANDLING PRECAUTIONS 10.2 SAFETY PRECAUTIONS 10.3 STORAGE PRECAUTIONS 11. REGULATORY STANDARD 11.1 SAFETY 12. MECHANICAL CHARACTERISTICS -------------------------------------------------------------------------------------------------------------

12 13

-------------------------------------------------------

19

-------------------------------------------------------

22

-------------------------------------------------------------------------------------------------------------

26 27

-------------------------------------------------------

30

--------------------------------------------------------------------------------------------------------------

31 32

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

REVISION HISTORY
Version Ver 2.0 Date 04, Mar 08 Page (New) All Section All Description Approval Specification was first issued.

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

1. GENERAL DESCRIPTION
1.1 OVERVIEW
V260B1- L11 is a TFT Liquid Crystal Display module with 5U-CCFL Backlight unit and 1ch-LVDS interface. The display diagonal is 26. This module supports 1366 x 768 WXGA format and can display 16.2M colors (6-bit+FRC colors). The inverter module for backlight is built-in.

1.2 FEATURES
- Excellent Brightness 500nits - Contrast Ratio 800:1 - Fast Response Time (8ms) - Color Saturation NTSC 72% - WXGA (1366 x 768 pixels) Resolution - DE (Data Enable) Only Mode - LVDS (Low Voltage Differential Signaling) Interface - Viewing Angle: 160(H)/150(V) (CR>10) TN Technology -Color Reproduction (Nature Color)

1.3 APPLICATION
- TFT LCD TVs - High Brightness, Multi-Media Displays

1.4 GENERAL SPECIFICATI0NS

Item Active Area Bezel Opening Area Driver Element Pixel Number Pixel Pitch (Sub Pixel) Pixel Arrangement Display Colors Display Operation Mode Surface Treatment

Specification 575.769 (H) x 323.712 (V) (26 Diagonal) 580.8 (H) x 328.8 (V) a-si TFT Active Matrix 1366 x R.G.B. x 768 0.1405 (H) x 0.4215 (V) RGB Vertical Stripe 16.2M Transmissive Mode / Normally White Anti-Glare Coating (Haze 25%) Hard Coating (3H)

Unit mm mm pixel mm color

Note (1)

1.5 MECHANICAL SPECIFICATIONS

Item Horizontal(H) Vertical(V) Module Size Depth(D) Depth(D) Weight Min. 625 372 31 45.7 Typ. 626 373 32 46.7 4200 Max. 627 374 33 47.7 Unit mm mm mm mm g Note To Rear To Inverter Cover

Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

2. ABSOLUTE MAXIMUM RATINGS

2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item Storage Temperature Operating Ambient Temperature Shock (Non-Operating) Vibration (Non-Operating) (a) 90 %RH Max. (Ta (c) No condensation. Note (2) The maximum operating temperature is based on the test condition that the surface temperature of display area is less than or equal to 65 C with LCD module alone in a temperature controlled chamber. Thermal management should be considered in final product design to prevent the surface temperature of display area from being over 65 C. The range of operating temperature may degrade in case of improper thermal management in final product design. Note (3) 11 ms, half sine wave, 1 time for X, Y, Z. Note (4) 10 ~ 500 Hz, 10 min, 1 time each X, Y, Z. Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture. 40 C). Symbol TST TOP SNOP VNOP Min. -20 0 Value Max. +60 +50 50 1.0 Unit C C G G Note (1) (1), (2) (3), (5) (4), (5)

Note (1) Temperature and relative humidity range is shown in the figure below. (b) Wet-bulb temperature should be 39 C Max. (Ta > 40 C).

Relative Humidity (%RH)

100 90 80 60 40 20 10 -40 -20 0

Operating Range

Storage Range
20 40 60 80

Temperature (C)

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

2.2 ELECTRICAL ABSOLUTE RATINGS 2.2.1 TFT LCD MODULE

Item Power Supply Voltage Input Signal Voltage Symbol Vcc VIN Min. -0.3 -0.3 Value Max. 13.0 3.6 Unit V V Note (1)

2.2.2 BACKLIGHT UNIT

Item Lamp Voltage Power Supply Voltage Control Signal Level Symbol VW VBL Test Condition Ta = 25 Min. 0 -0.3 Type Max. 3000 30 7 Unit VRMS V V Note (1) (1), (3)

Note (1) Permanent damage to the device may occur if maximum values are exceeded. Functional operation should be restricted to the conditions described under normal operating conditions. Note (2) No moisture condensation or freezing. Note (3) The control signals includes Backlight On/Off Control, Internal PWM Control and External PWM Control.

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE
Parameter Power Supply Voltage Power Supply Ripple Voltage Rush Current White Power Supply Current Black Vertical Stripe Differential Input High Threshold Voltage LVDS Differential Input Low Interface Threshold Voltage Common Input Voltage Terminating Resistor Input High Threshold Voltage CMOS interface Input Low Threshold Voltage Note (2) Measurement Conditions:
+12.0V Q1 AO4409 Vcc FUSE R1 200K C3 1uF (LCD Module Input)

Ta = 25 2 C Symbol VCC VRP IRUSH ICC VLVTH VLVTL VLVC RT VIH VIL -100 1.125 2.7 0 1.25 100 1.375 3.3 0.7 Min. 11.4 Value Typ. 12.0 Max. 12.6 300 3.0 0.25 0.55 0.45 +100 Unit V mV A A A A mV mV V ohm V V Note (1) (2) (3)

0.2 0.5 0.4

Note (1) The module should be always operated within above ranges.

VR1

47K (Low to High) (Control Signal) R2 SW 1K Q2 2N7002 10uF C1

Vcc rising time is 470us

+12V
0.9Vcc 0.1Vcc

GND 470us

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

Note (3) The specified power supply current is under the conditions at Vcc = 12 V, Ta = 25 2 C, f v = 60 Hz, whereas a power dissipation check pattern below is displayed. a. White Pattern b. Black Pattern

Active Area

Active Area

c. Vertical Stripe Pattern

R G B R G B B R G B R G B R B R G B R G B R R G B R G B
Active Area

3.2 BACKLIGHT INVERTER UNIT 3.2.1 CCFL (Cold Cathode Fluorescent Lamp) CHARACTERISTICS (Ta = 25 2 C)
Parameter Lamp Voltage Lamp Current Lamp Starting Voltage Operating Frequency Lamp Life Time Symbol VW IL VS FO LBL 40 50,000 7.0 Min. Value Typ. 1688 7.5 8.0 2830 2410 60,000 80 Max. Unit VRMS mARMS VRMS VRMS KHz Hrs Note IL = 7.5mA (1) (2), Ta = 0 C (2), Ta = 25 C (3) (4)

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

3.2.2 INVERTER CHARACTERISTICS (Ta = 25 2 C)

Parameter Power Consumption Input Voltage Input Current Input Inrush Current Input Ripple Noise Oscillating Frequency Dimming Frequency Minimum Duty Ratio FW FB DMIN 63 150 10 66 160 20 Symbol PBL VBL IBL 22.8 Min. Value Typ. 66 24 2.75 4.3 912 69 170 25.2 Max. Unit W VDC A Apeak mVP-P kHz Hz % Non Dimming VBL =24.0V VBL =22.8V Note (5)(6), IL = 7.5mA

Note (1) Lamp current is measured by utilizing high frequency current meters as shown below:

A A A A A A A A A A

HV (Pink) HV (White) HV (Pink) HV (White) HV (Pink) HV (White) HV (Pink) HV (White) HV (Pink) HV (White)

1 2 1 2 1 2 1 2 1 2

LCD Module

Inverter

Note (2) The lamp starting voltage VS should be applied to the lamp for more than 1 second under starting up duration. Otherwise the lamp could not be lighted on completed. Note (3) The lamp frequency may produce interference with horizontal synchronous frequency from the display, and this may cause line flow on the display. In order to avoid interference, the lamp frequency should be detached from the horizontal synchronous frequency and its harmonics as far as possible.

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

Note (4) The life time of a lamp is defined as when the brightness is larger than 50% of its original value and the effective discharge length is longer than 80% of its original length (Effective discharge length is defined as an area that has equal to or more than 70% brightness compared to the brightness at the center point.) as the time in which it continues to operate under the condition Ta = 25 2 and IL = 7.0~ 8.0mARMS.

Note (5) The power supply capacity should be higher than the total inverter power consumption PBL. Since the pulse width modulation (PWM) mode was applied for backlight dimming, the driving current changed as PWM duty on and off. The transient response of power supply should be considered for the changing loading when inverter dimming. Note (6) The measurement of Max. value is based on 26 backlight unit under 24V input voltage and 7.8mA lamp in average after lighting for 30 minutes. Note (7) 10% minimum duty ratio is only valid for electrical operation.

3.2.3 INVERTER INTERTFACE CHARACTERISTICS

Item Error Signal On/Off Control Voltage Internal PWM Control Voltage External PWM Control Voltage VBL Rising Time VBL Falling Time Control Signal Rising Time Control Signal Falling Time PWM Signal Rising Time PWM Signal Falling Time Input Impedance PWM Delay Time BLON Delay Time BLON Off Time ON OFF MAX MIN HI LO Symbol ERR VBLON VIPWM VEPWM Tr1 Tf1 Tr Tf TPWMR TPWMF RIN TPWM Ton Toff 1 100 300 300 300 500 500 2.0 0 3.0 2.0 0 30 30 3.15 0 5.0 0.8 50 50 100 100 50 50 5.0 0.8 3.3 V V V V V V ms ms ms ms us us M ms ms ms Maximum Duty Ratio Minimum Duty Ratio Duty On Duty Off Test Condition Min. Typ. Max. Unit Note (Note 2)

Note (1) The power sequence and control signal timing as shown in following figure. Note (2) When inverter protective function is triggered, ERR will output open collector status. In normal operation, the signal of ERR will output a low level voltage.

10

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

Tr1 VBL 0 VBLON 0 2.0V 0.8V Tr Backlight on duration Tf Ton Toff

Tf1

Ext. Dimming Function TPWMR VEPWM 0 2.0V 0.8V TPWM 3.3V VIPWM 0 Floating Int. Dimming Function T PWMF Floating

VW External PWM Period External PWM Duty 100% Minimun Duty

11

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

4. BLOCK DIAGRAM
4.1 TFT LCD MODULE
SCAN DRIVER IC

RX0(+/-) RX1(+/-) RX2(+/-) RX3(+/-) RXCLK(+/-)

TFT LCD PANEL (1366x3x768)

(P-TWO,196185-30041)

INPUT CONNECTOR

TIMING CONTROLLER

Vcc GND

DATA DRIVER IC DC/DC CONVERTER & REFERENCE VOLTAGE CN2-CN6 : CP042CP1MR0-LF (Cvilux) or equivalent

BACKLIGHT UNIT

CN1 VBL GND ERR BLON I_PWM E_PWM

INVERTER CONNECTOR CN1 : 1. S14B-PH-SM4-TB (JST) 2. CI0114M1HR0-LF (Cvilux) or equivalent

12

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

5. INTERFACE PIN CONNECTION

5.1 TFT LCD MODULE
CNF1 Connector Pin Assignment Pin No. Symbol Description 1 VCC Power supply: +12V 2 VCC Power supply: +12V 3 VCC Power supply: +12V 4 VCC Power supply: +12V 5 GND Ground 6 GND Ground 7 GND Ground 8 GND Ground 9 SELLVDS Select LVDS data format 10 NC No connection 11 GND Ground 12 RX0Negative transmission data of pixel 0 13 RX0+ Positive transmission data of pixel 0 14 GND Ground 15 RX1Negative transmission data of pixel 1 16 RX1+ Positive transmission data of pixel 1 17 GND Ground 18 RX2Negative transmission data of pixel 2 19 RX2+ Positive transmission data of pixel 2 20 GND Ground 21 RXCLKNegative of clock 22 RXCLK+ Positive of clock 23 GND Ground 24 RX3Negative transmission data of pixel 3 25 RX3+ Positive transmission data of pixel 3 26 GND Ground 27 NC No connection 28 NC No connection 29 GND Ground 30 GND Ground Note (1) Connector Part No.: P-TWO,196185-30041 or compatible Note (2) Ground or OPEN: Normal, High: JEIDA LVDS format Please refer to 5.5 LVDS INTERFACE (Page 17) Note (3) Reserved for internal use. Please leave it open. Note

(2) (3)

(3) (3)

13

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

5.2 BACKLIGHT UNIT

The pin configuration for the housing and leader wire is shown in the table below. CN2-CN6 (Housing) : CP0404S000(CviLux) or equivalent.

Pin No.
1 2

Symbol
HV HV

High Voltage High Voltage

Description

Wire Color Pink White

Note (1) The backlight interface housing for high voltage side is a model CP0404S000 (CviLux) or equivalent. The mating header on inverter part number is CP042CP1MR0-LF (CyiLux) or equivalent.

5 Male Connectors CP0404S000(CviLux) or Equivalent 1.HV(Pink,+) 2.HV(White,-)

1.HV(Pink,+) 2.HV(White,-)

1.HV(Pink,+) 2.HV(White,-)

1.HV(Pink,+) 2.HV(White,-)

1.HV(Pink,+) 2.HV(White,-)

14

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

5.3 INVERTER UNIT

CN1 (Header) : 1.S14B-PH-SM4-TB (JST) 2. CI0114M1HR0-LF (Cvilux) or equivalent. Pin No. Symbol Description 1 2 VBL +24V Power input 3 4 5 6 7 GND Ground 8 9 10 Normal (GND) 11 ERR Abnormal(Open collector) 12 BLON BL ON/OFF 13 I_PWM Internal PWM Control 14 E_PWM External PWM Control Notice: #PIN 13:Analog Dimming Control (Use Pin 13) : 0V~3.3V and Pin 14 must open. #PIN 14:PWM Dimming Control (Use Pin 14) : Pin 13 must open. #Pin 13 (I_PWM) and Pin 14 (E_PWM) can not open in same period.

CN2-CN6 (Header) : CP042CP1MR0-LF (Cvilux) or equivalent. Pin Name Description 1 CCFL HOT CCFL High Voltage 2 CCFL HOT CCFL High Voltage

15

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

5.4 BLOCK DIAGRAM OF INTERFACE CNF1

Rx0+ R0-R7 G0-G7 B0-B7 DE TxIN Rx0Rx1+ Rx1-

51
100pF

RxOUT

51 51
100pF

R0-R7 G0-G7 B0-B7

51

Rx2+ Rx2Rx3+ Rx3-

51
100pF

51 51
100pF

DE

51 51
100pF

Host Graphics Controller LVDS Transmitter THC63LVDM83A (LVDF83A)

R0~R7 : Pixel R Data G0~G7 : Pixel G Data B0~B7 : Pixel B Data DE : Data Enable Signal

CLK+ PLL CLK-

51

PLL

DCLK Timing Controller

LVDS Receiver THC63LVDF84A

Note (1) The system must have the transmitter to drive the module. Note (2) LVDS cable impedance shall be 50 ohms per signal line or about 100 ohms per twist-pair line when it is used differentially.

16

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

5.5 LVDS INTERFACE

SIGNAL TRANSMITTER THC63LVDM83A INTERFACE CONNECTOR RECEIVER THC63LVDF84A TFT CONTROL INPUT
SELLVD= SELLVDS L or OPEN

SELLVD= L or OPEN

SELLVDS =H R2 R3 R4 R5 R6 R7 G2 G3 G4 G5 G6 G7 B2 B3 B4 B5 B6 B7 DE R0 R1 G0 G1 B0 B1 RSVD 1 RSVD 2 RSVD 3 DCLK

PIN 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 30 50 2 8 10 16 18 25 27 28 31

INPUT TxIN0 TxIN1 TxIN2 TxIN3 TxIN4 TxIN6 TxIN7 TxIN8 TxIN9 TxIN12 TxIN13 TxIN14 TxIN15 TxIN18 TxIN19 TxIN20 TxIN21 TxIN22 TxIN26 TxIN27 TxIN5 TxIN10 TxIN11 TxIN16 TxIN17 TxIN23 TxIN24 TxIN25

Host

TFT-LCD

PIN 27 29

OUTPUT Rx OUT0 Rx OUT1 Rx OUT2 Rx OUT3 Rx OUT4 Rx OUT6 Rx OUT7 Rx OUT8 Rx OUT9 Rx OUT12 Rx OUT13 Rx OUT14 Rx OUT15 Rx OUT18 Rx OUT19 Rx OUT20 Rx OUT21 Rx OUT22 Rx OUT26 Rx OUT27 Rx OUT5 Rx OUT10 Rx OUT11 Rx OUT16 Rx OUT17 Rx OUT23 Rx OUT24 Rx OUT25

=H R2 R3 R4 R5 R6 R7 G2 G3 G4 G5 G6 G7 B2 B3 B4 B5 B6 B7 DE R0 R1 G0 G1 B0 B1 NC NC NC

R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 24 bit B2 B3 B4 B5 DE R6 R7 G6 G7 B6 B7 RSVD 1 RSVD 2 RSVD 3

R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 DE R6 R7 G6 G7 B6 B7 NC NC NC DCLK

TA OUT0+

Rx 0+

30 32 33

TA OUT0-

Rx 0-

35 37 38 39

TA OUT1+

Rx 1+

43 45 46

TA OUT1-

Rx 1-

47 51 53 54

TA OUT2+

Rx 2+

55 1 6

TA OUT2-

Rx 2-

7 34 41 42

TA OUT3+

Rx 3+

49 50 2

TA OUT3-

Rx 3-

3 5

TxCLK IN TxCLK OUT+ RxCLK IN+ 26 RxCLK OUT TxCLK OUT- RxCLK IN-

R0~R7: Pixel R Data (7; MSB, 0; LSB) G0~G7: Pixel G Data (7; MSB, 0; LSB) B0~B7: Pixel B Data (7; MSB, 0; LSB) DE : Data enable signal Notes(1) RSVD(reserved)pins on the transmitter shall be H or L. 17

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

5.6 COLOR DATA INPUT ASSIGNMENT

The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Data Signal Color Black Red Green Basic Blue Colors Cyan Magenta Yellow White Red(0) / Dark Red(1) Gray Scale Of Red Red(2) : : Red(253) Red(254) Red(255) Green(1) Gray Scale Of Green Green(2) : : Green(253) Green(254) Green(255) Blue(0) / Dark Blue(1) Gray Scale Of Blue Blue(2) : : Blue(253) Blue(254) Blue(255) 0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 Red 0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 1 0 0 0 1 1 1 0 0 1 : : 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 Green 0 0 0 0 0 1 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 : : : : : : : : : : 0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 1 : : 0 1 1 0 0 0 : : 0 0 0 0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 1 0 : : 1 0 1 0 0 0 : : 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 1 1 0 0 0 0 0 0 : : : : 0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 Blue 0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 : : : : : :
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0

1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : : : : : : : : :

0 0 0 0 0 0 0 0 0 0 0 0 : : : :

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : : : : :

Green(0) / Dark 0

0 1 1 1 1 0 1 1 1 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : : : : : : : : :

0 0 0 0 0 0 0 0 0 0 0 0 : : : :

0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 : : : : : :

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

1 1 1 1 1 1

1 0 1 1 1 0 1 1 1

Note (1) 0: Low Level Voltage, 1: High Level Voltage

18

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

6. INTERFACE TIMING
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
The input signal timing specifications are shown as the following table and timing diagram. Signal LVDS Receiver Clock LVDS Receiver Data Item Frequency Input cycle to cycle jitter Setup Time Hold Time Frame Rate Vertical Active Display Term Total Display Blank Total Horizontal Active Display Term Display Blank Symbol 1/Tc Trcl Tlvsu Tlvhd Fr5 Fr6 Tv Tvd Tvb Th Thd Thb 600 600 47 57 778 768 10 1442 1366 76 Min. 60 Typ. 76 Max. 82 200 Unit MHZ ps ps ps Hz Hz Th Th Th Tc Tc Tc Note

50 60 806 768 38 1560 1366 194

53 63 888 768 120 1936 1366 570

Tv=Tvd+Tvb Th=Thd+Thb -

Note (1) Since this module is operated in DE only mode, Hsync and Vsync input signals should be set to low logic level. Otherwise, this module would operate abnormally.

INPUT SIGNAL TIMING DIAGRAM

Tv Tvd Tvb

DE Th

DCLK Tc DE Thb Thd

DATA

Valid Display Data (1366 clocks)

19

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

LVDS RECEIVER INTERFACE TIMING DIAGRAM

Tc

RXCLK+/-

RXn+/Tlvsu Tlvhd

1T 14

3T 14

5T 14

7T 14

9T 14

11 T 14

13T 14

20

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

6.2 POWER ON/OFF SEQUENCE To prevent a latch-up or DC operation of LCD module, the power on/off sequence should be as the diagram below.

Power Supply VCC

0V 0.5 0 0 1s T1 T2 T3 T4 10 ms 50 ms 50 ms

0.9 VCC 0.1VCC

0.9 VCC 0.1Vcc

T1

T3

T2

T4

Signals
0V

VALID
Power On Power Off

Backlight (Recommended) 500 ms T5 100 ms T6

T5

50%

50%

T6

Power ON/OFF Sequence

Note (1) The supply voltage of the external system for the module input should follow the definition of Vcc. Note (2) Apply the lamp voltage within the LCD operation range. When the backlight turns on before the LCD operation or the LCD turns off before the backlight turns off, the display may momentarily become abnormal screen. Note (3) In case of Vcc is in off level, please keep the level of input signals on the low or high impedance. Note (4) T4 should be measured after the module has been fully discharged between power off and on period. Note (5) Interface signal shall not be kept at high impedance when the power is on.

21

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS
Item Ambient Temperature Ambient Humidity Supply Voltage Input Signal Lamp Current Oscillating Frequency (Inverter) Vertical Frame Rate Symbol Value Unit o Ta C 252 Ha %RH 5010 VCC 12.0 V According to typical value in "3. ELECTRICAL CHARACTERISTICS" IL mA 7.5 0.5 FW KHz 66 3 Fr 60 Hz

7.2 OPTICAL SPECIFICATIONS

The relative measurement methods of optical characteristics are shown in 7.2. The following items should be measured under the test conditions described in 7.1 and stable environment shown in Note (6). Item Contrast Ratio Response Time Center Luminance of White White Variation Cross Talk Red Green Color Chromaticity Blue White Color Gamut Horizontal Vertical Symbol CR TR TF W CT Rx Ry Gx Gy Bx By Wx Wy CG x+ Y+ YxCR10 68 70 70 70 60 x=0, Y =0 Viewing Angle at Normal Direction Typ. -0.03 0.637 0.330 0.273 0.596 0.151 0.065 0.280 0.285 72 80 80 80 70 Deg. (1) Typ. +0.03 LC 400 Condition Min. 600 Typ. 800 3 5 500 1.3 4 % % NTSC Ratio (6) 5 8 Max. Unit ms Note (2) (3) (4) (7) (5)

Viewing Angle

22

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

Note (1) Definition of Viewing Angle (x, y): Viewing angles are measured by EZ-Contrast 160R (Eldim) Normal x = y = 0 yX- = 90 xy+ y+ x+ 12 oclock direction y+ = 90

6 oclock y- = 90

y-

x+

X+ = 90

Note (2) Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L255 / L0 L255: Luminance of gray level 255 L 0: Luminance of gray level 0 CR = CR (5), CR (X) is corresponding to the Contrast Ratio of the point X at the figure in Note (7). Note (3) Definition of Response Time (TR, TF):

Gray Level 255

100% 90%

Gray Level 255

Optical Response
10% 0%

Gray Level 0

TR

TF

Time

23

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

Note (4) Definition of Luminance of White (LC): Measure the luminance of gray level 255 at center point and 5 points LC = L (5) L (X) is corresponding to the luminance of the point X at the figure in Note (7). Note (5) Definition of Cross Talk (CT): CT = | YB YA | / YA 100 (%) Where: YA = Luminance of measured location without gray level 0 pattern (cd/m2) YB = Luminance of measured location with gray level 0 pattern (cd/m2)
(0, 0)

Active Area
YA, U (D/2,W/8)

(0, 0) (D/4,W/4)

Active Area
YB, U (D/2,W/8)

YA, L (D/8,W/2)

Gray 128

YB, L (D/8,W/2) YA, R (7D/8,W/2) YB, D (D/2,7W/8) (D,W)

Gray 0
Gray 128

YB, R (7D/8,W/2) (3D/4,3W/4)

YA, D (D/2,7W/8)

(D,W)

Note (6) Measurement Setup: The LCD module should be stabilized at given temperature for 1 hour to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 1 hour in a windless room.

LCD Module LCD Panel Center of the Screen Display Color Analyzer (Minolta CA210)

Light Shield Room (Ambient Luminance < 2 lux)

24

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

Note (7) Definition of White Variation (W): Measure the luminance of gray level 255 at 5 points W = Maximum [L (1), L (2), L (3), L (4), L (5)] / Minimum [L (1), L (2), L (3), L (4), L (5)]

Horizontal Line D
D/4 D/2 3D/4

Vertical Line

W/4

2 X

W/2

: Test Point X=1 to 5

3W/4

Active Area

25

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

8. DEFINITION OF LABELS
8.1 CMO MODULE LABEL
The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation.

OPTOELECTRONICS

CHI

MEI

V260B1

-L11 Rev. XX

E207943
MADE IN TAIWAN

XXXXXXXYMDLNNNN

RoHS

OPTOELECTRONICS

CHI

MEI

V260B1

-L11 Rev. XX

E207943
MADE IN TAIWAN

MADE IN CHINA

XXXXXXXYMDLNNNN

LEOO(or CAPG)

RoHS

(a) Model Name: V260B1-L11 (b) Revision: Rev. XX, for example: A0, A1 B1, B2 or C1, C2etc. (c) Serial ID: X X X X X X X Y M D L N N N N Serial No. Product Line Year, Month, Date CMO Internal Use CMO Internal Use Revision CMO Internal Use Serial ID includes the information as below: (a) Manufactured Date: Year: 1~9, for 2001~2009 Month: 1~9, A~C, for Jan. ~ Dec. Day: 1~9, A~Y, for 1 to 31 , exclude I ,O, and U. (b) Revision Code: Cover all the change (c) Serial No.: Manufacturing sequence of product (d) Product Line: 1 -> Line1, 2 -> Line 2, etc.
st st

26

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

9. PACKAGING
9.1 PACKING SPECIFICATIONS
(1) 6 LCD TV Modules / Carton (2) Carton Dimensions : 713(L) X 429 (W) X 453 (H) (3) Weight : Approximately 29 Kg ( 6 Modules Per Carton)

9.2 PACKING METHOD

Figures 9-1 and 9-2 are the packing method

LCD TV Module

Anti-Static Bag

Cushion(Bottom)

2 pcs Drier

Carton

Carton Label

Figure.9-1 packing method

27

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

Sea / Land Transportation (40ft HQ Container)

Sea / Land Transportation (40ft Container)

PE Sheet

28

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

Air Transportation
Corner Protector

Figure. 9-2 packing method

29

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

10. PRECAUTIONS
10.1 ASSEMBLY AND HANDLING PRECAUTIONS
(1) Do not apply rough force such as bending or twisting to the module during assembly. (2) It is recommended to assemble or to install a module into the users system in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. (3) Do not apply pressure or impulse to the module to prevent the damage of LCD panel and backlight. (4) Always follow the correct power-on sequence when the LCD module is turned on. This can prevent the damage and latch-up of the CMOS LSI chips. (5) Do not plug in or pull out the I/F connector while the module is in operation. (6) Do not disassemble the module. (7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. (8) Moisture can easily penetrate into LCD module and may cause the damage during operation. (9) High temperature or humidity may deteriorate the performance of LCD module. Please store LCD modules in the specified storage conditions. (10) When ambient temperature is lower than 10C, the display quality might be reduced. For example, the response time will become slow, and the starting voltage of CCFL will be higher than that of room temperature.

10.2 SAFETY PRECAUTIONS

(1) The startup voltage of a backlight is over 1000 Volts. It may cause an electrical shock while assembling with the inverter. Do not disassemble the module or insert anything into the backlight unit. (2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. (3) After the modules end of life, it is not harmful in case of normal operation and storage.

10.3 STORAGE PRECAUTIONS

When storing modules as spares for a long time, the following precaution is necessary. (1) Do not leave the module in high temperature, and high humidity for a long time. It is highly recommended to store the module with temperature from 0 to 35 at normal humidity without condensation. (2) The module shall be stored in dark place. Do not store the TFT-LCD module in direct sunlight or fluorescent light.

30

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

11. REGULATORY STANDARDS 11.1 SAFETY

Regulatory Information Technology equipment Item UL cUL CB UL Audio/Video Apparatus cUL CB UL 60950-1: 2003 CAN/CSA C22.2 No.60950-1-03 IEC 60950-1:2001 UL 60065: 2003 CAN/CSA C22.2 No.60065-03 IEC 60065:2001 Standard

31

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

12. MECHANICAL CHARACTERISTICS

32

CHI MEI

Version 2.0

HIGH VOLTAGE C AU TION

RIS K OF ELE CT RI C SHOC K . DIS CONNE CT THE E LEC TRIC P OW E R B E F ORE S ERV IC ING .

33
H IG H V OL TAG E CAUTION
R ISK OF E LECTRI C SHOC K. D ISC ON N EC T THE E LECTRIC P OW ER B EFORE S ERV ICIN G .

COL D CATHOD E FLUORESCENT LAMP IN LCD PANEL CONTAI NS A S MALL AMOUNT OF MERCURY P LEASE FOLL OW L OCAL ORD INANCES OR REG UL ATIONS F OR D ISPOSAL.

CHI MEI

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Version 2.0

Approval

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

34

CHI MEI

Version 2.0

Issued Date: 04, Mar 2008 Model No.: V260B1 L11

Approval

35

CHI MEI

Version 2.0