Promass F

TI01034D/06/EN/08.
21 Products Solutions Services

71505580
2021-01-01
Technical Information
Proline Promass F 100
Coriolis flowmeter
The flowmeter with premium accuracy, robustness and an ultra-compact

transmitter
Application Your benefits
Measuring principle operates independently of physical fluid • Highest process safety – immune to fluctuating and harsh
properties such as viscosity or density environments
Device properties • Fewer process measuring points – multivariable
• Mass flow: measured error ±0.05 % (PremiumCal) measurement (flow, density, temperature)
• Pressure rating of sensor housing up to 40 bar (580 psi) • Space‐saving installation – no inlet/outlet run needs
• Nominal diameter: DN 8 to 250 (³⁄₈ to 10") • Space‐saving transmitter – full functionality on smallest
• Robust, ultra-compact transmitter housing footprint
• Highest degree of protection: IP69 • Time‐saving local operation without additional software and
• Local display available hardware – integrated web server
• Integrated verification – Heartbeat Technology
Table of contents
About this document . . . . . . . . . . . . . . . . . . . . . . . . 4 Shock resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Shock resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Interior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Electromagnetic compatibility (EMC) . . . . . . . . . . . . . . . 49
Function and system design . . . . . . . . . . . . . . . . . . . 5
Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Measuring system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Equipment architecture . . . . . . . . . . . . . . . . . . . . . . . . . 7 Medium temperature range . . . . . . . . . . . . . . . . . . . . . . 50
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Density . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Pressure-temperature ratings . . . . . . . . . . . . . . . . . . . . 50
Sensor housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rupture disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Measured variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Flow limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Measuring range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pressure loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Operable flow range . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
System pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Thermal insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Vibrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Ex connection data . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Mechanical construction . . . . . . . . . . . . . . . . . . . . 59
Low flow cut off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Dimensions in SI units . . . . . . . . . . . . . . . . . . . . . . . . . 59
Protocol-specific data . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Dimensions in US units . . . . . . . . . . . . . . . . . . . . . . . . . 79
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Terminal assignment . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Process connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Pin assignment, device plug . . . . . . . . . . . . . . . . . . . . . . 30 Surface roughness . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Operability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Operating concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Power supply failure . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Local display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Potential equalization . . . . . . . . . . . . . . . . . . . . . . . . . 39
Service interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Cable entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Cable specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Certificates and approvals . . . . . . . . . . . . . . . . . . . 96
CE mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
C-Tick symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Performance characteristics . . . . . . . . . . . . . . . . . . 41
Ex approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Reference operating conditions . . . . . . . . . . . . . . . . . . . 41
Sanitary compatibility . . . . . . . . . . . . . . . . . . . . . . . . . 97
Maximum measured error . . . . . . . . . . . . . . . . . . . . . . . 41
HART certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Repeatability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Certification PROFIBUS . . . . . . . . . . . . . . . . . . . . . . . . . 97
Response time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Certification PROFINET . . . . . . . . . . . . . . . . . . . . . . . . 98
Influence of ambient temperature . . . . . . . . . . . . . . . . . 43
EtherNet/IP certification . . . . . . . . . . . . . . . . . . . . . . . . 98
Influence of medium temperature . . . . . . . . . . . . . . . . . . 43
Modbus RS485 certification . . . . . . . . . . . . . . . . . . . . . 98
Influence of medium pressure . . . . . . . . . . . . . . . . . . . . 44
Pressure Equipment Directive . . . . . . . . . . . . . . . . . . . . 98
Design fundamentals . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Other standards and guidelines . . . . . . . . . . . . . . . . . . . 98
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Ordering information . . . . . . . . . . . . . . . . . . . . . . . 99

Mounting location . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Inlet and outlet runs . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Application packages . . . . . . . . . . . . . . . . . . . . . . . 99
Special mounting instructions . . . . . . . . . . . . . . . . . . . . 47 Heartbeat Technology . . . . . . . . . . . . . . . . . . . . . . . . . 99
Installing the Safety Barrier Promass 100 . . . . . . . . . . . . 48 Concentration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Special density . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Ambient temperature range . . . . . . . . . . . . . . . . . . . . . 49 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Device-specific accessories . . . . . . . . . . . . . . . . . . . . . . 100
Climate class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Communication-specific accessories . . . . . . . . . . . . . . . 100
Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Service-specific accessories . . . . . . . . . . . . . . . . . . . . . 101
Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 System components . . . . . . . . . . . . . . . . . . . . . . . . . . 102
2 Endress+Hauser
Supplementary documentation . . . . . . . . . . . . . . 102

Standard documentation . . . . . . . . . . . . . . . . . . . . . . . 102
Supplementary device-dependent documentation . . . . . . 103
Registered trademarks . . . . . . . . . . . . . . . . . . . . . 103
Endress+Hauser 3
About this document

Symbols used Electrical symbols
Symbol Meaning
Direct current
Alternating current
Direct current and alternating current
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a
grounding system.
Protective Earth (PE)

A terminal which must be connected to ground prior to establishing any other
connections.
The ground terminals are situated inside and outside the device:
• Inner ground terminal: Connects the protectiv earth to the mains supply.
• Outer ground terminal: Connects the device to the plant grounding system.
Symbols for certain types of information
Symbol Meaning
Permitted
Procedures, processes or actions that are permitted.
Preferred
Procedures, processes or actions that are preferred.
Forbidden
Procedures, processes or actions that are forbidden.
Tip
Indicates additional information.
Reference to documentation.
A Reference to page.
Reference to graphic.
Visual inspection.
Symbols in graphics
Symbol Meaning
1, 2, 3, ... Item numbers
1. , 2. , 3. , … Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
Hazardous area
-
Safe area (non-hazardous area)
.
Flow direction
4 Endress+Hauser
Function and system design

Measuring principle The measuring principle is based on the controlled generation of Coriolis forces. These forces are
always present in a system when both translational and rotational movements are superimposed.
Fc = 2 · ∆m (ν · ω)
Fc = Coriolis force
∆m = moving mass
ω = rotational velocity
ν = radial velocity in rotating or oscillating system
The amplitude of the Coriolis force depends on the moving mass ∆m, its velocity ν in the system and
thus on the mass flow. Instead of a constant rotational velocity ω, the sensor uses oscillation.
In the sensor, two parallel measuring tubes containing flowing fluid oscillate in antiphase, acting like
a tuning fork. The Coriolis forces produced at the measuring tubes cause a phase shift in the tube
oscillations (see illustration):
• At zero flow (when the fluid is at a standstill) the two tubes oscillate in phase (1).
• Mass flow causes deceleration of the oscillation at the inlet of the tubes (2) and acceleration at the
outlet (3).
1 2 3
A0028850
The phase difference (A-B) increases with increasing mass flow. Electrodynamic sensors register the
tube oscillations at the inlet and outlet. System balance is ensured by the antiphase oscillation of the
two measuring tubes. The measuring principle operates independently of temperature, pressure,
viscosity, conductivity and flow profile.
Density measurement
The measuring tube is continuously excited at its resonance frequency. A change in the mass and
thus the density of the oscillating system (comprising measuring tube and fluid) results in a
corresponding, automatic adjustment in the oscillation frequency. Resonance frequency is thus a
function of medium density. The microprocessor utilizes this relationship to obtain a density signal.
Volume measurement
Together with the measured mass flow, this is used to calculate the volume flow.
Temperature measurement
The temperature of the measuring tube is determined in order to calculate the compensation factor
due to temperature effects. This signal corresponds to the process temperature and is also available
as an output signal.
Endress+Hauser 5
Measuring system The device consists of a transmitter and a sensor. If a device with Modbus RS485 intrinsically safe is
ordered, the Safety Barrier Promass 100 is part of the scope of supply and must be implemented to
operate the device.
The device is available as a compact version:
The transmitter and sensor form a mechanical unit.
Transmitter
Promass 100 Device versions and materials:

• Compact, aluminum, coated:
Aluminum, AlSi10Mg, coated
• Compact, hygienic, stainless:
• Hygienic version, stainless steel 1.4301 (304)
• Optional: order code for "Sensor feature", option CC
A0016693 Hygienic version, for maximum corrosion resistance: stainless steel
1.4404 (316L)
• Ultra-compact, hygienic, stainless:
Hygienic version, for maximum corrosion resistance: stainless steel
A0016694 1.4404 (316L)
Configuration:
• Via operating tools (e.g. FieldCare, DeviceCare)
• Additionally for device version with local display:
Via Web browser (e.g. Microsoft Internet Explorer)
• Also for device version with 4-20 mA HART, pulse/frequency/switch
A0016695
output:
Via Web browser (e.g. Microsoft Internet Explorer)
• Also for device version with EtherNet/IP output:
• Via Web browser (e.g. Microsoft Internet Explorer)
• Via Add-on Profile Level 3 for automation system from Rockwell
Automation
• Via Electronic Data Sheet (EDS)
• Also for device version with PROFINET output:
• Via Web browser (e.g. Microsoft Internet Explorer)
• Via device master file (GSD)
Sensor
PromassF • Excellent performance across a wide range of applications

• Simultaneous measurement of flow, volume flow, density and
temperature (multivariable)
• Immune to process influences
• Nominal diameter range: DN 8 to 250 (³⁄₈ to 10")
• Materials:
A0016507 • Sensor: stainless steel, 1.4301/1.4307 (304L); optional 1.4404
(316/316L)
• Measuring tubes: stainless steel, 1.4539 (904L); 1.4404
(316/316L); Alloy C22, 2.4602 (UNS N06022)
• Process connections: stainless steel, 1.4404 (316/316L); 1.4301
(304); Alloy C22, 2.4602 (UNS N06022)
Safety Barrier Promass 100
• Dual-channel safety barrier for installation in non-hazardous locations

or zone 2/div. 2:
• Channel 1: DC 24 V power supply
• Channel 2: Modbus RS485
• In addition to current, voltage and power limitation, it offers galvanic
isolation of circuits for explosion protection.
• Easy top-hat rail mounting (DIN 35 mm) for installation in control
A0016763
cabinets
6 Endress+Hauser
Equipment architecture
1
2 3 4 5
10
11
6 7 8
A0016779
1 Possibilities for integrating measuring devices into a system

1 Control system (e.g. PLC)
2 EtherNet/IP
3 PROFIBUS DP
4 PROFINET
5 Modbus RS485
6 4-20 mA HART, pulse/frequency/switch output
7 Safety Barrier Promass 100
8 Modbus RS485 intrinsically safe
9 Non-hazardous area
10 Non-hazardous area and Zone 2/Div. 2
11 Hazardous area and Zone 1/Div. 1
Safety IT security
We only provide a warranty if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any inadvertent
changes to the device settings.
IT security measures in line with operators' security standards and designed to provide additional
protection for the device and device data transfer must be implemented by the operators themselves.
Endress+Hauser 7
Input
Measured variable Direct measured variables
• Mass flow
• Density
• Temperature
Calculated measured variables

• Volume flow
• Corrected volume flow
• Reference density
Measuring range Measuring ranges for liquids
DN Measuring range full scale values min(F) to max(F)
[mm] [in] [kg/h] [lb/min]
8 ³⁄₈ 0 to 2 000 0 to 73.50
15 ½ 0 to 6 500 0 to 238.9
25 1 0 to 18 000 0 to 661.5
40 1½ 0 to 45 000 0 to 1 654
50 2 0 to 70 000 0 to 2 573
80 3 0 to 180 000 0 to 6 615
100 4 0 to 350 000 0 to 12 860
150 6 0 to 800 000 0 to 29 400
250 10 0 to 2 200 000 0 to 80 850
Measuring ranges for gases

The full scale values depend on the density of the gas and can be calculated with the formula below:
max(G) =  max(F) · ρG : x
 max(G) Maximum full scale value for gas [kg/h]
 max(F) Maximum full scale value for liquid [kg/h]
 max(G) <  max(F)  max(G) can never be greater than  max(F)
ρG Gas density in [kg/m³] at operating conditions
x Constant dependent on nominal diameter
DN x
[mm] [in] [kg/m3]
8 ³⁄₈ 60
15 ½ 80
25 1 90
40 1½ 90
50 2 90
80 3 110
100 4 130
8 Endress+Hauser
DN x
[mm] [in] [kg/m3]
150 6 200
250 10 200
To calculate the measuring range, use the Applicator sizing tool →  101
Calculation example for gas

• Sensor: Promass F, DN 50
• Gas: Air with a density of 60.3 kg/m³ (at 20 °C and 50 bar)
• Measuring range (liquid): 70 000 kg/h
• x = 90 kg/m³ (for Promass F, DN 50)
Maximum possible full scale value:
 max(G) =  max(F) · ρG : x = 70 000 kg/h · 60.3 kg/m³ : 90 kg/m³ = 46 900 kg/h
Recommended measuring range

"Flow limit" section →  57
Operable flow range Over 1000 : 1.

Flow rates above the preset full scale value do not override the electronics unit, with the result that
the totalizer values are registered correctly.
Output
Output signal HART current output
Current output 4-20 mA HART (active)
Maximum output values • DC 24 V (no flow)

• 22.5 mA
Load 0 to 700 Ω
Resolution 0.38 µA
Damping Adjustable: 0.07 to 999 s
Assignable measured • Mass flow

variables • Volume flow
• Density
• Temperature
 The range of options increases if the measuring device has one or more
application packages.
Pulse/frequency/switch output
Function Can be set to pulse, frequency or switch output
Version Passive, open collector
Maximum input values • DC 30 V

• 25 mA
Voltage drop For 25 mA: ≤ DC 2 V
Pulse output
Pulse width Adjustable: 0.05 to 2 000 ms
Endress+Hauser 9
Maximum pulse rate 10 000 Impulse/s
Pulse value Adjustable

Frequency output
Output frequency Adjustable: 0 to 10 000 Hz
Damping Adjustable: 0 to 999 s
Pulse/pause ratio 1:1

• Density
• Temperature
Switch output
Switching behavior Binary, conductive or non-conductive
Switching delay Adjustable: 0 to 100 s
Number of switching Unlimited

cycles
Assignable functions • Off

• On
• Diagnostic behavior
• Limit value
• Mass flow
• Volume flow
• Density
• Temperature
• Totalizer 1-3
• Flow direction monitoring
• Status
• Partially filled pipe detection
• Low flow cut off
PROFIBUS DP
Signal encoding NRZ code
Data transfer 9.6 kBaud…12 MBaud
Modbus RS485
Physical interface In accordance with EIA/TIA-485-A standard
Terminating resistor • For device version used in non-hazardous areas or Zone 2/Div. 2: integrated
and can be activated via DIP switches on the transmitter electronics module
• For device version used in intrinsically safe areas: integrated and can be
activated via DIP switches on the Safety Barrier Promass 100
10 Endress+Hauser
EtherNet/IP
Standards In accordance with IEEE 802.3
PROFINET
Standards In accordance with IEEE 802.3
Signal on alarm Depending on the interface, failure information is displayed as follows:
Current output 4 to 20 mA
4 to 20 mA
Failure mode Choose from:
• 4 to 20 mA in accordance with NAMUR recommendation NE 43
• 4 to 20 mA in accordance with US
• Min. value: 3.59 mA
• Max. value: 22.5 mA
• Freely definable value between: 3.59 to 22.5 mA
• Actual value
• Last valid value
Pulse output

• Actual value
• No pulses
Frequency output

• Actual value
• 0 Hz
• Defined value: 0 to 12 500 Hz
Switch output

• Current status
• Open
• Closed
PROFIBUS DP
Status and alarm Diagnostics in accordance with PROFIBUS PA Profile 3.02

messages
Modbus RS485

• NaN value instead of current value
• Last valid value
EtherNet/IP
Device diagnostics Device condition can be read out in Input Assembly
Endress+Hauser 11
PROFINET
Device diagnostics According to "Application Layer protocol for decentralized periphery", Version 2.3
Local display
Plain text display With information on cause and remedial measures
Backlight Red backlighting indicates a device error.
Status signal as per NAMUR recommendation NE 107
Interface/protocol
• Via digital communication:
• HART protocol
• PROFIBUS DP
• Modbus RS485
• EtherNet/IP
• PROFINET
• Via service interface
CDI-RJ45 service interface
Additional information on remote operation →  92
Web server
Light emitting diodes (LED)
Status information Status indicated by various light emitting diodes

The following information is displayed depending on the device version:
• Supply voltage active
• Data transmission active
• Device alarm/error has occurred
• EtherNet/IP network available
• EtherNet/IP connection established
• PROFINET network available
• PROFINET connection established
• PROFINET blinking feature
Ex connection data These values only apply for the following device version:
Order code for "Output", option M "Modbus RS485", for use in intrinsically safe areas
Safety-related values
Terminal numbers
Supply voltage Signal transmission
2 (L-) 1 (L+) 26 (A) 27 (B)
Unom = DC 24 V Unom = DC 5 V
Umax = AC 260 V Umax = AC 260 V
12 Endress+Hauser
Intrinsically safe values

Terminal numbers
20 (L-) 10 (L+) 62 (A) 72 (B)
Uo = 16.24 V
Io = 623 mA
Po = 2.45 W
With IIC 1): Lo = 92.8 µH, Co = 0.433 μF, Lo/Ro = 14.6 μH/Ω
With IIB: Lo= 372 µH, Co = 2.57 μF, Lo/Ro = 58.3 μH/Ω
 For an overview and for information on the interdependencies between the gas group - sensor - nominal
diameter, see the "Safety Instructions" (XA) document for the measuring device
1) The gas group depends on the sensor and nominal diameter ff.
Transmitter
Intrinsically safe values

Order code for Terminal numbers
"Approval"
20 (L-) 10 (L+) 62 (A) 72 (B)
• Option BM: ATEX II2G + IECEx Z1 Ex ia, II2D Ex tb Ui = 16.24 V

• Option BO: ATEX II1/2G + IECEx Z0/Z1 Ex ia, II2D Ii = 623 mA
• Option BQ: ATEX II1/2G + IECEx Z0/Z1 Ex ia Pi = 2.45 W
• Option BU: ATEX II2G + IECEx Z1 Ex ia Li = 0 µH
• Option C2: CSA C/US IS Cl. I, II, III Div. 1 Ci = 6 nF
• Option 85: ATEX II2G + IECEx Z1 Ex ia + CSA C/US
IS Cl. I, II, III Div. 1
 For an overview and for information on the interdependencies between the gas group - sensor - nominal
diameter, see the "Safety Instructions" (XA) document for the measuring device
Low flow cut off The switch points for low flow cut off are user-selectable.
Protocol-specific data HART
Manufacturer ID 0x11
Device type ID 0x4A
HART protocol revision 7
Device description files Information and files under:

(DTM, DD) www.endress.com
HART load Min. 250 Ω
Endress+Hauser 13
Dynamic variables Read out the dynamic variables: HART command 3

The measured variables can be freely assigned to the dynamic variables.
Measured variables for PV (primary dynamic variable)
• Mass flow
• Volume flow
• Density
• Temperature
Measured variables for SV, TV, QV (secondary, tertiary and quaternary
dynamic variable)
• Mass flow
• Volume flow
• Density
• Temperature
• Totalizer 1
• Totalizer 2
• Totalizer 3
Heartbeat Technology application package
Additional measured variables are available with the Heartbeat Technology
application package:
• Carrier pipe temperature
• Oscillation amplitude 0
Device variables Read out the device variables: HART command 9

The device variables are permanently assigned.
A maximum of 8 device variables can be transmitted:
• 0 = mass flow
• 1 = volume flow
• 2 = corrected volume flow
• 3 = density
• 4 = reference density
• 5 = temperature
• 6 = totalizer 1
• 7 = totalizer 2
• 8 = totalizer 3
• 13 = target mass flow
• 14 = carrier mass flow
• 15 = concentration
PROFIBUS DP
Ident number 0x1561
Profile version 3.02
Device description files (GSD, Information and files under:

DTM, DD) • www.endress.com
On the product page for the device: Documents/Software → Device drivers
• www.profibus.org
14 Endress+Hauser
Output values Analog input 1 to 8

(from measuring device to • Mass flow
automation system) • Volume flow
• Target mass flow
• Carrier mass flow
• Density
• Concentration
• Temperature
• Electronic temperature
• Oscillation frequency
• Oscillation amplitude
• Frequency fluctuation
• Oscillation damping
• Tube damping fluctuation
• Signal asymmetry
• Exciter current
Digital input 1 to 2
• Partially filled pipe detection
Totalizer 1 to 3
• Mass flow
• Volume flow
Input values Analog output 1 to 3 (fixed assignment)

(from automation system to • Pressure
measuring device) • Temperature
Digital output 1 to 3 (fixed assignment)
• Digital output 1: switch positive zero return on/off
• Digital output 2: perform zero point adjustment
• Digital output 3: switch switch output on/off
Totalizer 1 to 3
• Totalize
• Reset and hold
• Preset and hold
• Stop
• Operating mode configuration:
• Net flow total
• Forward flow total
• Reverse flow total
Supported functions • Identification & Maintenance

Simplest device identification on the part of the control system and
nameplate
• PROFIBUS upload/download
Reading and writing parameters is up to ten times faster with PROFIBUS
upload/download
• Condensed status
Simplest and self-explanatory diagnostic information by categorizing
diagnostic messages that occur
Configuration of the device • DIP switches on the I/O electronics module

address • Via operating tools (e.g. FieldCare)
Modbus RS485
Protocol Modbus Applications Protocol Specification V1.1
Device type Slave
Slave address range 1 to 247
Broadcast address range 0
Endress+Hauser 15
Function codes • 03: Read holding register

• 04: Read input register
• 06: Write single registers
• 08: Diagnostics
• 16: Write multiple registers
• 23: Read/write multiple registers
Broadcast messages Supported by the following function codes:

• 06: Write single registers
• 16: Write multiple registers
• 23: Read/write multiple registers
Supported baud rate • 1 200 BAUD

• 2 400 BAUD
• 4 800 BAUD
• 9 600 BAUD
• 19 200 BAUD
• 38 400 BAUD
• 57 600 BAUD
• 115 200 BAUD
Data transfer mode • ASCII

• RTU
Data access Each device parameter can be accessed via Modbus RS485.
 For Modbus register information, see "Description of device parameters"

documentation
EtherNet/IP
Protocol • The CIP Networks Library Volume 1: Common Industrial Protocol

• The CIP Networks Library Volume 2: EtherNet/IP Adaptation of CIP
Communication type • 10Base-T

• 100Base-TX
Device profile Generic device (product type: 0x2B)
Manufacturer ID 0x49E
Device type ID 0x104A
Baud rates Automatic ¹⁰⁄₁₀₀ Mbit with half-duplex and full-duplex detection
Polarity Auto-polarity for automatic correction of crossed TxD and RxD pairs
Supported CIP connections Max. 3 connections
Explicit connections Max. 6 connections
I/O connections Max. 6 connections (scanner)
Configuration options for • DIP switches on the electronics module for IP addressing
measuring device • Manufacturer-specific software (FieldCare)
• Add-on Profile Level 3 for Rockwell Automation control systems
• Web browser
• Electronic Data Sheet (EDS) integrated in the measuring device
Configuration of the EtherNet • Speed: 10 MBit, 100 MBit, auto (factory setting)
interface • Duplex: half-duplex, full-duplex, auto (factory setting)
Configuration of the device • DIP switches on the electronics module for IP addressing (last octet)
address • DHCP
• Manufacturer-specific software (FieldCare)
• Add-on Profile Level 3 for Rockwell Automation control systems
• Web browser
• EtherNet/IP tools, e.g. RSLinx (Rockwell Automation)
Device Level Ring (DLR) No
16 Endress+Hauser
Fix Input
RPI 5 ms to 10 s (factory setting: 20 ms)
Exclusive Owner Multicast Instance Size [byte]
Instance configuration: 0x68 398
O → T configuration: 0x66 64
T → O configuration: 0x64 44
Instance configuration: 0x69 -
Input only Multicast Instance Size [byte]
O → T configuration: 0xC7 -
Input Assembly • Current device diagnostics

• Mass flow
• Volume flow
• Density
• Temperature
• Totalizer 1
• Totalizer 2
• Totalizer 3
Configurable Input
RPI 5 ms to 10 s (factory setting: 20 ms)
Endress+Hauser 17
Configurable Input Assembly • Current device diagnostics

• Mass flow
• Volume flow
• Density
• Temperature
• Totalizer 1
• Totalizer 2
• Totalizer 3
 The range of options increases if the measuring device has one or

more application packages.
Fix Output
Output Assembly • Activation of reset totalizers 1-3

• Activation of pressure compensation
• Activation of reference density compensation
• Activation of temperature compensation
• Reset totalizers 1-3
• External pressure value
• Pressure unit
• External reference density
• Reference density unit
• External temperature
• Temperature unit
Configuration
Configuration Assembly Only the most common configurations are listed below.
• Software write protection
• Mass flow unit
• Mass unit
• Volume flow unit
• Volume unit
• Corrected volume flow unit
• Corrected volume unit
• Density unit
• Reference density unit
• Temperature unit
• Pressure unit
• Length
• Totalizer 1-3:
• Assignment
• Unit
• Operating mode
• Failsafe mode
• Alarm delay
PROFINET
Protocol "Application layer protocol for decentral device periphery and distributed
automation", version 2.3
Conformity class B
Communication type 100 MBit/s
Device profile Application interface identifier 0xF600

Generic device
Device type ID 0x844A
Device description files (GSD, Information and files under:

DTM) • www.endress.com
On the product page for the device: Documents/Software → Device drivers
• www.profibus.org
Baud rates Automatic 100 Mbit/s with full-duplex detection
18 Endress+Hauser
Cycle times From 8 ms
Polarity Auto-polarity for automatic correction of crossed TxD and RxD pairs
Supported connections • 1 x AR (Application Relation)

• 1 x Input CR (Communication Relation)
• 1 x Output CR (Communication Relation)
• 1 x Alarm CR (Communication Relation)
Configuration options for • DIP switches on the electronics module, for device name assignment (last
measuring device part)
• Manufacturer-specific software (FieldCare, DeviceCare)
• Web browser
• Device master file (GSD), can be read out via the integrated Web server of
the measuring device
Configuration of the device • DIP switches on the electronics module, for device name assignment (last
name part)
• DCP protocol
Output values Analog Input module (slot 1 to 14)

(from measuring device to • Mass flow
automation system) • Volume flow
• Target mass flow
• Carrier mass flow
• Density
• Concentration
• Temperature
• Electronic temperature
• Oscillation frequency
• Oscillation amplitude
• Frequency fluctuation
• Oscillation damping
• Tube damping fluctuation
• Signal asymmetry
• Exciter current
Discrete Input module (slot 1 to 14)
• Empty pipe detection
Diagnostics Input module (slot 1 to 14)
• Last diagnostics
• Current diagnosis
Totalizer 1 to 3 (slot 15 to 17)
• Mass flow
• Volume flow
Heartbeat Verification module (fixed assignment)
Verification status (slot 23)
Endress+Hauser 19
Input values Analog Output module (fixed assignment)

(from automation system to • External pressure (slot 18)
measuring device) • External temperature (slot 19)
• External reference density (slot 20)
Discrete Output module (fixed assignment)
• Activate/deactivate positive zero return (slot 21)
• Perform zero point adjustment (slot 22)
Totalizer 1 to 3 (slot 15 to 17)
• Totalize
• Reset and hold
• Preset and hold
• Stop
• Operating mode configuration:
• Net flow total
• Forward flow total
• Reverse flow total
Heartbeat Verification module (fixed assignment)
Start verification (slot 23)
Supported functions • Identification & Maintenance

Simple device identification via:
• Control system
• Nameplate
• Measured value status
The process variables are communicated with a measured value status
• Blinking feature via the local display for simple device identification and
assignment
Administration of software options

Input/output value Process variable Category Slot
Output value Mass flow Process variable 1 to 14
Volume flow
Corrected volume flow
Density
Reference density
Temperature
Electronic temperature
Oscillation frequency
Frequency fluctuation
Oscillation damping
Oscillation frequency
Signal asymmetry
Exciter current
Empty pipe detection
Low flow cut off
Current device diagnostics
Previous device diagnostics
Output value Target mass flow Concentration 1) 1 to 14
Carrier mass flow
Concentration
Output value Carrier pipe temperature Heartbeat 2) 1 to 14
20 Endress+Hauser
Input/output value Process variable Category Slot
Oscillation damping 1
Oscillation frequency 1
Oscillation amplitude 0
Oscillation amplitude 1
Frequency fluctuation 1
Tube damping fluctuation 1
Exciter current 1
Input value External density Process monitoring 18
External temperature 19
External reference density 20
Flow override 21
Zero point adjustment 22

2)
Status verification Heartbeat Verification 23
1) Only available with the "Concentration" application package.

2) Only available with the "Heartbeat" application package.
Endress+Hauser 21
Startup configuration
Startup configuration If startup configuration is enabled, the configuration of the most important
(NSU) device parameters is taken from the automation system and used.
The following configuration is taken from the automation system:
• Management
• Software revision
• Write protection
• System units
• Mass flow
• Mass
• Volume flow
• Volume
• Corrected volume
• Density
• Temperature
• Pressure
• Concentration application package
• Coefficients A0 to A4
• Coefficients B1 to B3
• Sensor adjustment
• Process parameter
• Damping (flow, density, temperature)
• Flow override
• Assign process variable
• Switch-on/switch-off point
• Pressure shock suppression
• Empty pipe detection
• Assign process variable
• Limit values
• Response time
• Max. damping
• Corrected volume flow calculation
• External reference density
• Fixed reference density
• Reference temperature
• Linear expansion coefficient
• Square expansion coefficient
• Measuring mode
• Medium
• Gas type
• Reference sound velocity
• Temperature coefficient sound velocity
• External compensation
• Pressure compensation
• Pressure value
• External pressure
• Diagnostic settings
• Diagnostic behavior for diverse diagnostic information
22 Endress+Hauser
Power supply
Terminal assignment Overview: housing version and connection versions
1 2
1.1 1.2 1.3 2.1 2.2
3 4
C 3.1 3.2 4.1 4.2
A0016770
A Housing version: compact, aluminum coated

B Housing version: compact, hygienic, stainless
C Housing version: ultra-compact, hygienic, stainless
1 Connection version: 4-20 mA HART, pulse/frequency/switch output
1.1 Signal transmission: pulse/frequency/switch output
1.2 Signal transmission: 4-20 mA HART
1.3 Supply voltage
2 Connection version: Modbus RS485
2.1 Signal transmission
2.2 Supply voltage
3 Connection versions: EtherNet/IP and PROFINET
3.2 Supply voltage
4 Connection version: PROFIBUS DP
4.2 Supply voltage
Transmitter
Connection version 4-20 mA HART with pulse/frequency/switch output

Order code for "Output", option B
Endress+Hauser 23
Depending on the housing version, the transmitters can be ordered with terminals or device plugs.
Connection methods available

Order code Possible options for order code
"Housing" Power "Electrical connection"
Outputs
supply
Options Terminals Terminals • Option A: coupling M20x1

A, B • Option B: thread M20x1
• Option C: thread G ½"
• Option D: thread NPT ½"
Options Device plugs Terminals • Option L: plug M12x1 + thread NPT ½"
A, B →  31 • Option N: plug M12x1 + coupling M20
• Option P: plug M12x1 + thread G ½"
• Option U: plug M12x1 + thread M20
Options Device plugs Device plugs Option Q: 2 x plug M12x1

A, B, C →  31 →  31
Order code for "Housing":

• Option A: compact, coated aluminum
• Option B: compact, hygienic, stainless
• Option C ultra-compact, hygienic, stainless
24 +
_ 3
25
26 +
_ 2
27
1 L+
1
2 L_
A0016888
2 Terminal assignment 4-20 mA HART with pulse/frequency/switch output

1 Power supply: DC 24 V
2 Output 1: 4-20 mA HART (active)
3 Output 2: pulse/frequency/switch output (passive)
Terminal number
Order code
Power supply Output 1 Output 2
"Output"
2 (L-) 1 (L+) 27 (–) 26 (+) 25 (–) 24 (+)
Option B DC 24 V 4-20 mA HART (active) Pulse/frequency/switch

output (passive)
Order code for "Output":

Option B: 4-20 mA HART with pulse/frequency/switch output
24 Endress+Hauser
PROFIBUS DP connection version

For use in the non-hazardous area and Zone 2/Div. 2
Order code for "Output", option L


Output
supply

Options Device plug Terminals • Option L: plug M12x1 + thread NPT ½"
A, B connectors • Option N: plug M12x1 + coupling M20
→  31 • Option P: plug M12x1 + thread G ½"
Options Device plug Device plug Option Q: 2 x plug M12x1

A, B, C connectors connectors
→  31 →  31

26 B
27 A 2
1 L+
1
2 L_
A0022716
3 PROFIBUS DP terminal assignment

2 PROFIBUS DP
Terminal number
Order code Power supply Output

"Output"
2 (L-) 1 (L+) 26 (RxD/TxD-P) 27 (RxD/TxD-
N)
Option L DC 24 V B A

Option L: PROFIBUS DP, for use in non-hazardous areas and Zone 2/Div. 2
Endress+Hauser 25
Modbus RS485 connection version

For use in the non-hazardous area and Zone 2/Div. 2
Order code for "Output", option M


Output
supply

Options Device plugs Terminals • Option L: plug M12x1 + thread NPT ½"
A, B →  31 • Option N: plug M12x1 + coupling M20
• Option P: plug M12x1 + thread G ½"
Options Device plugs Device plugs Option Q: 2 x plug M12x1

A, B, C →  31 →  31

• Option C: ultra-compact, hygienic, stainless
26 B
2
27 A
1 L+
1
2 L_
A0019528
4 Modbus RS485 terminal assignment, connection version for use in non-hazardous areas and Zone 2/Div.
2
2 Modbus RS485
Terminal number
Order code
Power supply Output
"Output"
1 (L+) 2 (L-) 26 (B) 27 (A)
Option M DC 24 V Modbus RS485

Option M: Modbus RS485, for use in non-hazardous areas and Zone 2/Div. 2
26 Endress+Hauser
Modbus RS485 connection version

For use in the intrinsically safe area. Connection via Safety Barrier Promass 100.
Order code for "Output", option M


Output
supply

A, B, C Device plugs Option I: plug M12x1

→  31

62 B
2
72 A
10 L+
1
20 L_
A0030219
5 Modbus RS485 terminal assignment, connection version for use in intrinsically safe areas (connection via
Safety Barrier Promass 100)
1 Intrinsically safe power supply
2 Modbus RS485
Order code
10 (L+) 20 (L-) 62 (B) 72 (A)
"Output"
Option M Intrinsically safe supply voltage Modbus RS485 intrinsically safe

Option M: Modbus RS485, for use in the intrinsically safe area (connection via Safety Barrier Promass 100)
Endress+Hauser 27
EtherNet/IP connection version

Order code for "Output", option N

Output
supply

→  32 →  32

1 L+
1
2 L_
A0017054
6 EtherNet/IP terminal assignment

2 EtherNet/IP
Terminal number
Order code
Power supply Output
"Output"
2 (L-) 1 (L+) Device plug M12x1
Option N DC 24 V EtherNet/IP

Option N: EtherNet/IP
28 Endress+Hauser
PROFINET connection version

Order code for "Output", option R

Output
supply

→  30 →  30

1 L+
1
2 L_
A0017054
7 PROFINET terminal assignment

2 PROFINET
Terminal number
Order code
Power supply Output
"Output"
2 (L-) 1 (L+) Device plug M12x1
Option R DC 24 V PROFINET

Option R: PROFINET
Endress+Hauser 29
2 1 26 27
L L+ B A
Power Modbus
supply RS485
1 24VDC
Safe area
Power
Lift panel for
bus termination
Communication
A
Safety Barrier
Promass 100
Hazardous area
A Power Modbus
supply RS485
L L+ B A
20 10 62 72
2
A0030220
8 Safety Barrier Promass 100 with terminals

1 Non-hazardous area, Zone 2, Class I Division 2
2 Intrinsically safe area
Pin assignment, device plug Order codes for the M12x1 connectors, see the "Order code for electrical connection" column:
• 4-20 mA HART, pulse/frequency/switch output →  23
• PROFIBUS DP→  25
• Modbus RS485 →  26
• EtherNet/IP →  28
• PROFINET→  29
Supply voltage
For all connection versions except MODBUS RS485 intrinsically safe (device side)
Device plug MODBUS RS485 intrinsically safe with supply voltage →  31
2 Pin Assignment
1 L+ DC 24 V
2 Not assigned
3 1
3 Not assigned
5 4 L- DC 24 V
4
A0029042
5 Grounding/shielding
Coding Plug/socket
A Plug
The following is recommended as a socket:

• Binder, series 763, part no. 79 3440 35 05
• Alternatively: Phoenix part no. 1669767 SAC-5P-M12MS
• With the order code for "Output", option B: 4-20 mA HART, pulse/frequency/switch output
• With the order code for "Output", option N: EtherNet/IP
• When using the device in a hazardous location: Use a suitably certified socket.
30 Endress+Hauser
4-20 mA HART with pulse/frequency/switch output
Device plug for signal transmission (device side)
2 Pin Assignment
1 + 4-20 mA HART (active)
2 - 4-20 mA HART (active)

1 3
3 + Pulse/frequency/switch output (passive)
5 4 - Pulse/frequency/switch output (passive)
4
A0016810
Coding Plug/socket
A Socket
 •• When
Recommended plug: Binder, series 763, part no. 79 3439 12 05
using the device in a hazardous location, use a suitably certified plug.
PROFIBUS DP
For use in the non-hazardous area and Zone 2/Div. 2.
2 Pin Assignment
1 Not assigned
2 A PROFIBUS DP
1 3
3 Not assigned
5 4 B PROFIBUS DP
4
A0016811
Coding Plug/socket
B Socket
 •• When
MODBUS RS485
Device plug for signal transmission with supply voltage (device side), MODBUS RS485 (intrinsically
safe)
2 Pin Assignment
1 L+ Supply voltage, intrinsically safe
2 A
3 1 Modbus RS485 intrinsically safe
3 B
5 4 L- Supply voltage, intrinsically safe
4
A0029042
Coding Plug/socket
A Plug
 •• Recommended socket: Binder, series 763, part no. 79 3439 12 05

When using the device in a hazardous location: Use a suitably certified socket.
Endress+Hauser 31
Device plug for signal transmission (device side), MODBUS RS485 (not intrinsically safe)
For use in the non-hazardous area and Zone 2/Div. 2.
2 Pin Assignment
1 Not assigned
2 A Modbus RS485
1 3
3 Not assigned
5 4 B Modbus RS485
4
A0016811
Coding Plug/socket
B Socket
 •• When
EtherNet/IP
2 Pin Assignment
1 + Tx
2 + Rx
1 3
3 - Tx
4 - Rx
4
A0016812
Coding Plug/socket
D Socket
 Recommended plug:
• Phoenix, part no. 1543223 SACC-M12MSD-4Q
• When using the device in a hazardous location, use a suitably certified plug.
PROFINET
2 Pin Assignment
1 + TD +
2 + RD +
1 3
3 - TD –
4 - RD –
4
A0016812
Coding Plug/socket
D Socket
 Recommended plug:
• Phoenix, part no. 1543223 SACC-M12MSD-4Q
• When using the device in a hazardous location, use a suitably certified plug.
Supply voltage The power unit must be tested to ensure it meets safety requirements (e.g. PELV, SELV).
32 Endress+Hauser
Transmitter
For device version with communication type:
• HART, PROFIBUS DP, EtherNet/IP: DC 20 to 30 V
• Modbus RS485, device version:
• For use in the non-hazardous area and Zone 2/Div. 2: DC 20 to 30 V
• For use in the intrinsically safe area: power supply via Safety Barrier Promass 100
Promass 100 safety barrier

DC 20 to 30 V
Power consumption Transmitter
Maximum
Order code for "Output"
Power consumption
Option B: 4-20 mA HART with pulse/frequency/switch output 3.5 W
Option L: PROFIBUS DP 3.5 W
Option M Modbus RS485, for use in non-hazardous areas and Zone 2/

3.5 W
Div. 2
Option M: Modbus RS485, for use in intrinsically safe areas 2.45 W
Option N: EtherNet/IP 3.5 W
Option R: PROFINET 3.5 W

Maximum
Power consumption
Option M: Modbus RS485, for use in intrinsically safe areas 4.8 W
Current consumption Transmitter
Maximum Maximum
Current consumption switch-on current
Option B: 4-20mA HART, pul./freq./switch output 145 mA 18 A (< 0.125 ms)
Option L: PROFIBUS DP 145 mA 18 A (< 0.125 ms)
Option M Modbus RS485, for use in non-hazardous

90 mA 10 A (< 0.8 ms)
areas and Zone 2/Div. 2
Option M: Modbus RS485, for use in intrinsically safe

145 mA 16 A (< 0.4 ms)
areas
Option N: EtherNet/IP 145 mA 18 A (< 0.125 ms)
Option R: PROFINET 145 mA 18 A (< 0.125 ms)
Maximum Maximum
Current consumption switch-on current
Option M: Modbus RS485, for use in intrinsically safe

230 mA 10 A (< 0.8 ms)
areas
Power supply failure Depending on the device version, the configuration is retained in the device memoryor in the
pluggable data memory (HistoROM DAT).
Endress+Hauser 33
Electrical connection Connecting the transmitter
A B C
1 2 1 2 3 4
A0016924
A Housing version: compact, aluminum coated

B Housing version: compact hygienic, stainless
1 Cable entry or device plug for signal transmission
2 Cable entry or device plug for supply voltage
C Housing version: ultra-compact, hygienic, stainless, M12 device plug
3 Device plug for signal transmission
4 Device plug for supply voltage
• Terminal assignment→  23
• Pin assignment, device plug→  30
In the case of device versions with a connector, the transmitter housing does not need to be
opened to connect the signal cable or power supply cable.
Connection examples
Current output 4 to 20 mA HART
1 2 3
4...20 mA
4 5
A0029055
9 Connection example for 4 to 20 mA HART current output (active)

1 Automation system with current input (e.g. PLC)
2 Cable shield: the cable shield must be grounded at both ends to comply with EMC requirements; observe cable
specifications →  39
3 Connection for HART operating devices →  92
4 Resistor for HART communication (≥ 250 Ω): observe maximum load
5 Analog display unit: observe maximum load
6 Transmitter
34 Endress+Hauser
1 2 3 4
4...20 mA
A0028762
 10 Connection example for 4 to 20 mA HART current output (passive)

1 Automation system with current input (e.g. PLC)
2 Power supply
4 Analog display unit: observe maximum load
5 Transmitter
Pulse/frequency output
1 2
12345
A0028761
 11 Connection example for pulse/frequency output (passive)

1 Automation system with pulse/frequency input (e.g. PLC)
2 Power supply
3 Transmitter: Observe input values →  9
Switch output
1 2
A0028760
 12 Connection example for switch output (passive)

1 Automation system with switch input (e.g. PLC)
2 Power supply
3 Transmitter: Observe input values
Endress+Hauser 35
PROFIBUS DP
1 2 3
A A
4
B
B
A
4
B
A0028765
 13 Connection example for PROFIBUS DP, non-hazardous area and Zone 2/Div. 2
specifications
3 Transmitter
If baud rates > 1.5 MBaud an EMC cable entry must be used and the cable shield must continue
as far as the terminal wherever possible.
Modbus RS485
Modbus RS485, non-hazardous area and Zone 2/Div. 2
1 2 3
A A
4
B
B
A
4
B
A0028765
 14 Connection example for Modbus RS485, non-hazardous area and Zone 2/Div. 2
3 Distribution box
4 Transmitter
36 Endress+Hauser
Modbus RS485 intrinsically safe
1 2 3 4
A A
A A B B
L+ 8
B L+
B
L- L+ L- L-
5 6 7
A0028766
 15 Connection example for Modbus RS485 intrinsically safe

2 Cable shield, observe cable specifications
3 Safety Barrier Promass 100
4 Observe cable specifications
5 Non-hazardous area
6 Non-hazardous area and Zone 2/Div. 2
7 Intrinsically safe area
8 Transmitter
EtherNet/IP
1 2 3 4
A0028767
 16 Connection example for EtherNet/IP

2 Ethernet switch
4 Device plug
5 Transmitter
Endress+Hauser 37
PROFINET
1 2 3 4
A0016805
 17 Connection example for PROFINET

2 Ethernet switch
4 Device plug
5 Transmitter
HART input
1 2 3 4
4...20 mA
+
5
-
-
+ 6
A0019828
 18 Connection example for HART input (burst mode) via current output (active)
3 Connection for HART operating devices
4 Analog display unit
5 Transmitter
6 Sensor for external measured variable
38 Endress+Hauser
1 2 3 4 5
4...20 mA
+
+ 6
-
-
-
+
-
7
+
4...20 mA
2 3 4 5
A0019830
 19 Connection example for HART input (master mode) via current output (active)
1 Automation system with current input (e.g. PLC).
Prerequisite: automation system with HART version 6, HART commands 113 and 114 can be processed.
4 Connection for HART operating devices
5 Analog display unit
6 Transmitter
7 Sensor for external measured variable
Potential equalization Requirements

No special measures for potential equalization are required.
Please consider the following to ensure correct measurement:
• Same electrical potential for the fluid and sensor
• Company-internal grounding concepts
For devices intended for use in hazardous locations, please observe the guidelines in the
Ex documentation (XA).
Terminals Transmitter
Spring terminals for wire cross-sections0.5 to 2.5 mm2 (20 to 14 AWG)
Plug-in screw terminals for wire cross-sections0.5 to 2.5 mm2 (20 to 14 AWG)
Cable entries • Cable gland: M20 × 1.5 with cable Ø 6 to 12 mm (0.24 to 0.47 in)
• Thread for cable entry:
• M20
• G ½"
• NPT ½"
Cable specification Permitted temperature range

• The installation guidelines that apply in the country of installation must be observed.
• The cables must be suitable for the minimum and maximum temperatures to be expected.
Power supply cable

Standard installation cable is sufficient.
Signal cable
Current output 4 to 20 mA HART

A shielded cable is recommended. Observe grounding concept of the plant.
Standard installation cable is sufficient.
Endress+Hauser 39
PROFIBUS DP
The IEC 61158 standard specifies two types of cable (A and B) for the bus line which can be used for
every transmission rate. Cable type A is recommended.
Cable type A
Characteristic impedance 135 to 165 Ω at a measuring frequency of 3 to 20 MHz
Cable capacitance < 30 pF/m
Wire cross-section > 0.34 mm2 (22 AWG)
Cable type Twisted pairs
Loop resistance ≤110 Ω/km
Signal damping Max. 9 dB over the entire length of the cable cross-section
Shield Copper braided shielding or braided shielding with foil shield. When grounding
the cable shield, observe the grounding concept of the plant.
Modbus RS485
The EIA/TIA-485 standard specifies two types of cable (A and B) for the bus line which can be used
for every transmission rate. Cable type A is recommended.
Cable type A
Characteristic impedance 135 to 165 Ω at a measuring frequency of 3 to 20 MHz
Cable capacitance < 30 pF/m
Wire cross-section > 0.34 mm2 (22 AWG)
Cable type Twisted pairs
Loop resistance ≤110 Ω/km
Signal damping Max. 9 dB over the entire length of the cable cross-section
Shield Copper braided shielding or braided shielding with foil shield. When grounding
the cable shield, observe the grounding concept of the plant.
EtherNet/IP
The standard ANSI/TIA/EIA-568-B.2 Annex specifies CAT 5 as the minimum category for a cable
used for EtherNet/IP. CAT 5e and CAT 6 are recommended.
For more information on planning and installing EtherNet/IP networks, please refer to the
"Media Planning and Installation Manual. EtherNet/IP" of ODVA Organization
PROFINET
Standard IEC 61156-6 specifies CAT 5 as the minimum category for a cable used for PROFINET. CAT
5e and CAT 6 are recommended.
For more information on planning and installing PROFINET networks, see: "PROFINET Cabling
and Interconnection Technology", Guideline for PROFINET
Connecting cable between Safety Barrier Promass 100 and measuring device
Cable type Shielded twisted-pair cable with 2x2 wires. When grounding the cable shield,
observe the grounding concept of the plant.
Maximum cable resistance 2.5 Ω, one side
Comply with the maximum cable resistance specifications to ensure the operational reliability
of the measuring device.
40 Endress+Hauser
The maximum cable length for individual wire cross-sections is specified in the table below. Observe
the maximum capacitance and inductance per unit length of the cable and connection values for
hazardous areas .
Wire cross-section Maximum cable length
[mm2] [AWG] [m] [ft]
0.5 20 70 230
0.75 18 100 328
1.0 17 100 328
1.5 16 200 656
2.5 14 300 984
Performance characteristics
Reference operating • Error limits based on ISO 11631
conditions • Water with +15 to +45 °C (+59 to +113 °F) at2 to 6 bar (29 to 87 psi)
• Specifications as per calibration protocol
• Accuracy based on accredited calibration rigs that are traced to ISO 17025.
To obtain measured errors, use the Applicator sizing tool →  101
Maximum measured error o.r. = of reading; 1 g/cm³ = 1 kg/l; T = medium temperature
Base accuracy
Design fundamentals →  44
Mass flow and volume flow (liquids)

±0.05 % o.r. (PremiumCal; order code for "Calibration flow", option D, for mass flow)
±0.10 % o.r.
Mass flow (gases)

±0.25 % o.r.
Density (liquids)
Under reference conditions Standard density calibration Wide-range

Density specification 1) 2)
[g/cm³] [g/cm³] [g/cm³]
±0.0005 ±0.0005 ±0.001
1) Valid range for special density calibration: 0 to 2 g/cm³, +5 to +80 °C (+41 to +176 °F)
2) Order code for "Application package", option EE "Special density"
Temperature
±0.5 °C ± 0.005 · T °C (±0.9 °F ± 0.003 · (T – 32) °F)
Endress+Hauser 41
Zero point stability
DN Zero point stability
[mm] [in] [kg/h] [lb/min]
8 ³⁄₈ 0.030 0.001
15 ½ 0.200 0.007
25 1 0.540 0.019
40 1½ 2.25 0.083
50 2 3.50 0.129
80 3 9.0 0.330
100 4 14.0 0.514
150 6 32.0 1.17
250 10 88.0 3.23
Flow values
Flow values as turndown parameter depending on nominal diameter.
SI units
DN 1:1 1:10 1:20 1:50 1:100 1:500
[mm] [kg/h] [kg/h] [kg/h] [kg/h] [kg/h] [kg/h]
8 2 000 200 100 40 20 4
15 6 500 650 325 130 65 13
25 18 000 1 800 900 360 180 36
40 45 000 4 500 2 250 900 450 90
50 70 000 7 000 3 500 1 400 700 140
80 180 000 18 000 9 000 3 600 1 800 360
100 350 000 35 000 17 500 7 000 3 500 700
150 800 000 80 000 40 000 16 000 8 000 1 600
250 2 200 000 220 000 110 000 44 000 22 000 4 400
US units
DN 1:1 1:10 1:20 1:50 1:100 1:500
[inch] [lb/min] [lb/min] [lb/min] [lb/min] [lb/min] [lb/min]
³⁄₈ 73.50 7.350 3.675 1.470 0.735 0.147
½ 238.9 23.89 11.95 4.778 2.389 0.478
1 661.5 66.15 33.08 13.23 6.615 1.323
1½ 1 654 165.4 82.70 33.08 16.54 3.308
2 2 573 257.3 128.7 51.46 25.73 5.146
3 6 615 661.5 330.8 132.3 66.15 13.23
4 12 860 1 286 643.0 257.2 128.6 25.72
6 29 400 2 940 1 470 588 294 58.80
10 80 850 8 085 4 043 1 617 808.5 161.7
42 Endress+Hauser
Accuracy of outputs
The output accuracy must be factored into the measured error if analog outputs are used, but
can be ignored for fieldbus outputs (e.g. Modbus RS485, EtherNet/IP).
The outputs have the following base accuracy specifications.
Current output
Accuracy Max. ±5 µA
o.r. = of reading
Accuracy Max. ±50 ppm o.r. (over the entire ambient temperature range)
Repeatability o.r. = of reading; 1 g/cm3 = 1 kg/l; T = medium temperature
Base repeatability
Design fundamentals →  44
Mass flow and volume flow (liquids)

±0.025 % o.r. (PremiumCal, for mass flow)
±0.05 % o.r.
Mass flow (gases)

±0.20 % o.r.
Density (liquids)
±0.00025 g/cm3
Temperature
±0.25 °C ± 0.0025 · T °C (±0.45 °F ± 0.0015 · (T–32) °F)
Response time The response time depends on the configuration (damping).
Influence of ambient Current output

temperature
o.r. = of reading
Temperature coefficient Max. ±0.005 % o.r./°C
Temperature coefficient No additional effect. Included in accuracy.
Influence of medium Mass flow and volume flow

temperature
o.f.s. = of full scale value
When there is a difference between the temperature for zero point adjustment and the process
temperature, the additional measured error of the sensor is typically ±0.0002 % o.f.s./°C (±0.0001 %
o. f.s./°F).
The effect is reduced if zero point adjustment is performed at process temperature.
Density
When there is a difference between the density calibration temperature and the process
temperature, the typical measured error of the sensor is
±0.00005 g/cm3 /°C (±0.000025 g/cm3 /°F). Field density calibration is possible.
Endress+Hauser 43
Wide-range density specification (special density calibration)

If the process temperature is outside the valid range (→  41) the measured error is
±0.00005 g/cm3 /°C (±0.000025 g/cm3 /°F)
3
[kg/m ]
18
16
14
12 1
10
8
2
6
4
2
0
-50 0 100 200 300 [°C]
-80 0 80 160 240 320 400 480 560 [°F]

A0034654
1 Field density calibration, for example at +20 °C (+68 °F)

2 Special density calibration
Temperature
±0.005 · T °C (± 0.005 · (T – 32) °F)
Influence of medium The table below shows the effect on accuracy of mass flow due to a difference between calibration
pressure pressure and process pressure.
o.r. = of reading
It is possible to compensate for the effect by:
• Reading in the current pressure measured value via the current input.
• Specifying a fixed value for the pressure in the device parameters.
Operating Instructions .
DN [% o.r./bar] [% o.r./psi]
[mm] [in]
8 3/8 no influence
15 ½ no influence
25 1 no influence
40 1½ –0.003 –0.0002
50 2 –0.008 –0.0006
80 3 –0.009 –0.0006
100 4 –0.007 –0.0005
150 6 –0.009 –0.0006
250 10 –0.009 –0.0006
Design fundamentals o.r. = of reading, o.f.s. = of full scale value

BaseAccu = base accuracy in % o.r., BaseRepeat = base repeatability in % o.r.
MeasValue = measured value; ZeroPoint = zero point stability
44 Endress+Hauser
Calculation of the maximum measured error as a function of the flow rate

Flow rate Maximum measured error in % o.r.
ZeroPoint
³ BaseAccu ⋅ 100 ± BaseAccu
A0021339
A0021332
ZeroPoint ZeroPoint
< BaseAccu ⋅ 100 MeasValue ⋅ 100
±
A0021333 A0021334
Calculation of the maximum repeatability as a function of the flow rate

Flow rate Maximum repeatability in % o.r.
½ ⋅ ZeroPoint
³ BaseRepeat ⋅ 100
A0021340
A0021335
½ ⋅ ZeroPoint ZeroPoint
< BaseRepeat ⋅ 100 ± ½ ⋅ MeasValue ⋅ 100
A0021336 A0021337
Example for maximum measured error
E [%]
2.5
2.0
1.5
1.0
0.5
0
0 10 20 30 40 50 60 70 80 90 100 Q [%]
A0028808
E Maximum measured error in % o.r. (example with PremiumCal)

Q Flow rate in % of maximum full scale value
Installation
No special measures such as supports etc. are necessary. External forces are absorbed by the
construction of the device.
Mounting location
A0028772
To prevent measuring errors arising from accumulation of gas bubbles in the measuring tube, avoid
the following mounting locations in the pipe:
• Highest point of a pipeline.
• Directly upstream of a free pipe outlet in a down pipe.
Endress+Hauser 45
Installation in down pipes

However, the following installation suggestion allows for installation in an open vertical pipeline.
Pipe restrictions or the use of an orifice with a smaller cross-section than the nominal diameter
prevent the sensor running empty while measurement is in progress.
A0028773
 20 Installation in a down pipe (e.g. for batching applications)

1 Supply tank
2 Sensor
3 Orifice plate, pipe restriction
4 Valve
5 Batching tank
DN Ø orifice plate, pipe restriction
[mm] [in] [mm] [in]
8 ³⁄₈ 6 0.24
15 ½ 10 0.40
25 1 14 0.55
40 1½ 22 0.87
50 2 28 1.10
80 3 50 1.97
100 4 65 2.60
150 6 90 3.54
250 10 150 5.91
Orientation The direction of the arrow on the sensor nameplate helps you to install the sensor according to the
flow direction (direction of medium flow through the piping).
Orientation Recommendation
A Vertical orientation
A0015591
1)
B Horizontal orientation, transmitter at
top Exceptions:
→  21,  47
A0015589
46 Endress+Hauser
Orientation Recommendation
2)
C Horizontal orientation, transmitter at
bottom Exceptions:
→  21,  47
A0015590
D Horizontal orientation, transmitter at

side
A0015592
1) Applications with low process temperatures may decrease the ambient temperature. To maintain the
minimum ambient temperature for the transmitter, this orientation is recommended.
2) Applications with high process temperatures may increase the ambient temperature. To maintain the
maximum ambient temperature for the transmitter, this orientation is recommended.
If a sensor is installed horizontally with a curved measuring tube, match the position of the sensor to
the fluid properties.
1 2
A0028774
 21 Orientation of sensor with curved measuring tube

1 Avoid this orientation for fluids with entrained solids: Risk of solids accumulating.
2 Avoid this orientation for outgassing fluids: Risk of gas accumulating.
Inlet and outlet runs No special precautions need to be taken for fittings which create turbulence, such as valves, elbows
or T-pieces, as long as no cavitation occurs →  57.
Special mounting Rupture disk

instructions
Information that is relevant to the process: (Verweisziel existiert nicht, aber @y.link.required='true').
The position of the rupture disk is indicated on a sticker beside it.
The transportation guard must be removed.
The existing connecting nozzles are not intended for the purpose of rinsing or pressure monitoring,
but instead serve as the mounting location for the rupture disk.
In the event of a failure of the rupture disk, a discharge device can be screwed onto the internal
thread of the rupture disk in order to drain off any escaping medium.
Endress+Hauser 47
DN 8 (!⁄#")...150 (6") DN 250 (10")
RUPTURE DISK
2 3 1 2 3
A0028903
1 Rupture disk label

2 Rupture disk with 1/2" NPT internal thread with 1" width across flat
3 Transport protection
For information on the dimensions: see the "Mechanical construction -> Accessories" section
Zero point adjustment

All measuring devices are calibrated in accordance with state-of-the-art technology. Calibration
takes place under reference conditions→  41. Therefore, a zero point adjustment in the field is
generally not required.
Experience shows that zero point adjustment is advisable only in special cases:
• To achieve maximum measuring accuracy even with low flow rates.
• Under extreme process or operating conditions (e.g. very high process temperatures or very high-
viscosity fluids).
Installing the Safety Barrier

> 22.5 > 22.5
Promass 100
(> 0.89) (> 0.89)
A0016894
 22 Minimum distance between additional Safety Barrier Promass 100 or other modules. Engineering unit
mm (in)
48 Endress+Hauser
Environment
Ambient temperature range Measuring device • –40 to +60 °C (–40 to +140 °F)
• Order code for "Test, certificate", option JM:
–50 to +60 °C (–58 to +140 °F)
Safety Barrier Promass 100 –40 to +60 °C (–40 to +140 °F)
‣ If operating outdoors:
Avoid direct sunlight, particularly in warm climatic regions.
Storage temperature –40 to +80 °C (–40 to +176 °F), preferably at +20 °C (+68 °F) (standard version)
–50 to +80 °C (–58 to +176 °F) (Order code for "Test, certificate", option JM)
Climate class DIN EN 60068-2-38 (test Z/AD)
Degree of protection Transmitter and sensor

• As standard: IP66/67, type 4X enclosure
• With the order code for "Sensor options", option CM: IP69 can also be ordered
• When housing is open: IP20, type 1 enclosure
• Display module: IP20, type 1 enclosure
IP20
Vibration resistance • Oscillation, sinusoidal, following IEC 60068-2-6

• 2 to 8.4 Hz, 3.5 mm peak
• 8.4 to 2 000 Hz, 1 g peak
• Oscillation, broadband noise following IEC 60068-2-64
• 10 to 200 Hz, 0.003 g2/Hz
• 200 to 2 000 Hz, 0.001 g2/Hz
• Total: 1.54 g rms
Shock resistance Shock, half-sine according to IEC 60068-2-27

6 ms 30 g
Shock resistance Shock due to rough handling following IEC 60068-2-31
Interior cleaning • Cleaning in place (CIP)

• Sterilization in place (SIP)
Options
• Oil- and grease-free version for wetted parts, without declaration
Order code for "Service", option HA
• Oil- and grease-free version for wetted parts as per IEC/TR 60877-2.0 and BOC 50000810-4, with
declaration
Order code for "Service", option HB
Electromagnetic • Depends on the communication protocol:

compatibility (EMC) • HART, PROFIBUS DP, EtherNet/IP:
As per IEC/EN 61326 and NAMUR Recommendation 21 (NE 21)
• Modbus RS485:
As per IEC/EN 61326 and NAMUR Recommendation 21 (NE 21)
• PROFINET: as per IEC/EN 61326
• Complies with emission limits for industry as per EN 55011 (Class A)
• Device version with PROFIBUS DP: Complies with emission limits for industry as per EN 50170
Volume 2, IEC 61784
The following applies for PROFIBUS DP: If baud rates > 1.5 MBaud, an EMC cable entry must be
used and the cable shield must continue as far as the terminal wherever possible.
Details are provided in the Declaration of Conformity.
Endress+Hauser 49
Process
Medium temperature range
Standard version –50 to +150 °C (–58 to +302 °F) Order code for "Measuring tube
mat., wetted surface", option HA,
SA, SB, SC
Extended temperature version –50 to +240 °C (–58 to +464 °F) Order code for "Measuring tube
mat., wetted surface", option SD, SE,
SF, TH
Dependency of ambient temperature on medium temperature
Ta
A
B
Tm
A0031121
 23 Exemplary representation, values in the table below.

Ta Ambient temperature range
Tm Medium temperature
A Maximum permitted medium temperature Tm at Ta max = 60 °C (140 °F); higher medium temperatures Tm
require a reduced ambient temperature Ta
B Maximum permitted ambient temperature Ta for the maximum specified medium temperature Tm of the
sensor
Values for devices used in the hazardous area:

Separate Ex documentation (XA) for the device .
Not insulated Insulated
A B A B
Version Ta Tm Ta Tm Ta Tm Ta Tm
Standard version 60 °C (140 °F) 150 °C (302 °F) – – 60 °C (140 °F) 110 °C (230 °F) 55 °C (131 °F) 150 °C (302 °F)
Extended 60 °C (140 °F) 160 °C (320 °F) 55 °C (131 °F) 240 °C (464 °F) 60 °C (140 °F) 110 °C (230 °F) 50 °C (122 °F) 240 °C (464 °F)
temperature
version
Density 0 to 5 000 kg/m3 (0 to 312 lb/cf)
Pressure-temperature The following pressure/temperature diagrams apply to all pressure-bearing parts of the device and
ratings not just the process connection. The diagrams show the maximum permissible medium pressure
depending on the specific medium temperature.
Pressure-temperature curves with temperature range +151 to +240 °C (+304 to +464 °F)
exclusively for extended temperature version of measuring devices.
50 Endress+Hauser
Flange according to EN 1092-1 (DIN 2501)
[psi] [bar]
100
1400 PN 100
90
1200 80
1000 70
60 PN 63
800
50
600 40
PN 40
400 30
20
200
10 PN 16
0 0
-50 0 50 100 150 200 250 [°C]
-80 0 80 160 240 320 400 480 [°F]

A0034658-EN
 24 With flange material 1.4404 (F316/F316L), Alloy C22
Flange according to ASME B16.5
[psi] [bar]
100
1400 Class 600
90
1200 80
1000 70
60
800
50
Class 300
600 40
400 30
20
200 Class 150
10
0 0
-50 0 50 100 150 200 250[°C]
-80 0 80 160 240 320 400 480 [°F]

A0034659-EN
 25 With flange material 1.4404 (F316/F316L)
Endress+Hauser 51
[psi] [bar]
100 Class 600
1400
90
1200 80
1000 70
60
800
50
Class 300
600 40
400 30
20
200 Class 150
10
0 0
-50 0 50 100 150 200 250 [°C]
-80 0 80 160 240 320 400 480 [°F]

A0034660-EN
 26 With flange material Alloy C22
Flange JIS B2220
[psi] [bar]
1200 70
60 63K
800
50
600 40
40K
400 30
20
200 20K
10
10K
0 0
-50 0 50 100 150 200 250 [°C]
-80 0 80 160 240 320 400 480 [°F]

A0034665-EN
 27 With flange material 1.4404 (F316/F316L), Alloy C22
Flange DIN 11864-2 Form A
[psi] [bar]
50
600 40
400 30 DN 8…40
20
200
10 ≥ DN 50
0 0
-50 0 50 100 150 200 250 [°C]
-80 0 80 160 240 320 400 480 [°F]

A0028782-EN
 28 With connection material 1.4404 (316/316L)
52 Endress+Hauser
Lap joint flange according to EN 1092-1 (DIN 2501)
[psi] [bar]
50
600 40
PN 40
400 30
20
200
10
0 0
-50 0 50 100 150 200 250 [°C]
-80 0 80 160 240 320 400 480 [°F]

A0028784-EN
 29 With flange material 1.4301 (F304); wetted parts Alloy C22
Lap joint flange according to ASME B16.5
[psi] [bar]
100
1400 Class 600
90
1200 80
1000 70
60
800 Class 300
50
600 40
400 30
Class 150
20
200
10
0 0
-50 0 50 100 150 200 250 [°C]
-80 0 80 160 240 320 400 480 [°F]

A0028785-EN
Lap joint flange JIS B2220
[psi] [bar]
400 30
20
200 20K
10
0 0
-50 0 50 100 150 200 250 [°C]
-80 0 80 160 240 320 400 480 [°F]

A0028786-EN
Endress+Hauser 53
Thread DIN 11851
[psi] [bar]
50
600 40
DN 8…40
400 30
20 ≥ DN 50
200
10
0 0
-50 0 50 100 150 200 250 [°C]
-80 0 80 160 240 320 400 480 [°F]

A0028794-EN
DIN 11851 allows for applications up to +140 °C (+284 °F) if suitable sealing materials are used.
Please take this into account when selecting seals and counterparts, as these components can limit
the pressure and temperature range.
Thread DIN 11864-1 Form A
[psi] [bar]
50
600 40
DN 8…40
400 30
20 ≥ DN 50
200
10
0 0
-50 0 50 100 150 200 250 [°C]
-80 0 80 160 240 320 400 480 [°F]

A0028798-EN
Thread ISO 2853
[psi] [bar]
400
20
200
10
0 0
-50 0 50 100 150 200 250 [°C]
-80 0 80 160 240 320 400 480 [°F]

A0028799-EN
54 Endress+Hauser
Thread SMS 1145
[psi] [bar]
400
20
200
10
0 0
-50 0 50 100 150 200 250 [°C]
-80 0 80 160 240 320 400 480 [°F]

A0028800-EN
SMS 1145 allows for applications up to 16 bar (232 psi) if suitable sealing materials are used. Please
take this into account when selecting seals and counterparts, as these components can limit the
pressure and temperature range.
VCO
[psi] [bar]
100
1400
90
1200 80
1000 70
60
800
-50 0 50 100 150 200 250 [°C]
-80 0 80 160 240 320 400 480 [°F]

A0028801-EN
Tri-Clamp
[psi] [bar]
400
20
200
10
0 0
-50 0 50 100 150 200 250 [°C]
-80 0 80 160 240 320 400 480 [°F]

A0032216-EN
The clamp connections are suitable up to a maximum pressure of 16 bar (232 psi). Please observe
the operating limits of the clamp and seal used as they can be over 16 bar (232 psi). The clamp and
seal are not included in the scope of supply.
Sensor housing
For standard versions with the temperature range –50 to +150 °C (–58 to +302 °F), the sensor
housing is filled with dry nitrogen gas and protects the electronics and mechanics inside.
For all other temperature versions the sensor housing is filled with dry inert gas.
If a measuring tube fails (e.g. due to process characteristics like corrosive or abrasive fluids), the
fluid will initially be contained by the sensor housing.
Endress+Hauser 55
In the event of a tube failure, the pressure level inside the sensor housing will rise according to the
operating process pressure. If the user judges that the sensor housing burst pressure does not
provide an adequate safety margin, the device can be fitted with a rupture disk. This prevents
excessively high pressure from forming inside the sensor housing. Therefore, the use of a rupture
disk is strongly recommended in applications involving high gas pressures, and particularly in
applications in which the process pressure is greater than 2/3 of the sensor housing burst pressure.
If there is a need to drain the leaking medium into a discharge device, the sensor should be fitted
with a rupture disk. Connect the discharge to the additional threaded connection →  78.
If the sensor is to be purged with gas (gas detection), it should be equipped with purge connections.
Do not open the purge connections unless the containment can be filled immediately with a
dry, inert gas. Use only low pressure to purge.
Maximum pressure:
• DN 08 to 150 (3/8 to 6"): 5 bar (72.5 psi)
• DN 250 (10"):
• Medium temperature ≤ 100 °C (212 °F): 5 bar (72.5 psi)
• Medium temperature > 100 °C (212 °F): 3 bar (43.5 psi)
Burst pressure of the sensor housing
The following sensor housing burst pressures are only valid for standard devices and/or devices
equipped with closed purge connections (not opened/as delivered).
If a device fitted with purge connections (order code for "Sensor option", option CH "Purge
connection") is connected to the purge system, the maximum pressure is determined by the purge
system itself or by the device, depending on which component has the lower pressure classification.
If the device is fitted with a rupture disk (order code for "Sensor option", option CA "Rupture disk"), the
rupture disk trigger pressure is decisive .
The sensor housing burst pressure refers to a typical internal pressure which is reached prior to
mechanical failure of the sensor housing and which was determined during type testing. The
corresponding type test declaration can be ordered with the device (order code for "Additional
approval", option LN "Sensor housing burst pressure, type test").
DN Sensor housing burst pressure
[mm] [in] [bar] [psi]
8 ³⁄₈ 400 5 800
15 ½ 350 5 070
25 1 280 4 060
40 1½ 260 3 770
50 2 180 2 610
80 3 120 1 740
100 4 95 1 370
150 6 75 1 080
250 10 50 720
For information on the dimensions: see the "Mechanical construction" section
Rupture disk To increase the level of safety, a device version with a rupture disk with a trigger pressure of
10 to 15 bar (145 to 217.5 psi)can be used (order code for "Sensor option", option CA "rupture disk").
The use of rupture disks cannot be combined with the separately available heating jacket.
For information on the dimensions: see the "Mechanical construction" section (accessories) →  78
56 Endress+Hauser
Flow limit Select the nominal diameter by optimizing between the required flow range and permissible pressure
loss.
For an overview of the full scale values for the measuring range, see the "Measuring range"
section →  8
• The minimum recommended full scale value is approx. 1/20 of the maximum full scale value
• In most applications, 20 to 50 % of the maximum full scale value can be considered ideal
• A low full scale value must be selected for abrasive media (such as liquids with entrained solids):
flow velocity < 1 m/s (< 3 ft/s).
• For gas measurement the following rules apply:
• The flow velocity in the measuring tubes should not exceed half the sound velocity (0.5 Mach).
• The maximum mass flow depends on the density of the gas: formula →  8
To calculate the flow limit, use the Applicator sizing tool →  101
Pressure loss To calculate the pressure loss, use the Applicator sizing tool →  101
Promass F with reduced pressure loss: order code for "Sensor option", option CE "Reduced pressure
loss"
System pressure It is important that cavitation does not occur, or that gases entrained in the liquids do not outgas.
This is prevented by means of a sufficiently high system pressure.
For this reason, the following mounting locations are recommended:
• At the lowest point in a vertical pipe
• Downstream from pumps (no danger of vacuum)
A0028777
Thermal insulation In the case of some fluids, it is important to keep the heat radiated from the sensor to the
transmitter to a low level. A wide range of materials can be used for the required insulation.
The following device versions are recommended for versions with thermal insulation:
• Version with extended neck for insulation:
Order code for "Sensor option", option CG with an extended neck length of 105 mm (4.13 in).
• Extended temperature version:
Order code for "Measuring tube material", option SD, SE, SF or TH with an extended neck length of
105 mm (4.13 in).
NOTICE
Electronics overheating on account of thermal insulation!
‣ Recommended orientation: horizontal orientation, transmitter housing pointing downwards.
‣ Do not insulate the transmitter housing .
‣ Maximum permissible temperature at the lower end of the transmitter housing: 80 °C (176 °F)
‣ Thermal insulation with extended neck free: We recommend that you do not insulate the
extended neck in order to ensure optimum dissipation of heat.
A0034391
 37 Thermal insulation with extended neck free
Endress+Hauser 57
Heating Some fluids require suitable measures to avoid loss of heat at the sensor.
Heating options
• Electrical heating, e.g. with electric band heaters
• Via pipes carrying hot water or steam
• Via heating jackets
Heating jackets for the sensors can be ordered as accessories from Endress+Hauser. →  100
NOTICE
Danger of overheating when heating
‣ Ensure that the temperature at the lower end of the transmitter housing does not exceed
80 °C (176 °F).
‣ Ensure that sufficient convection takes place at the transmitter neck.
‣ Ensure that a sufficiently large area of the transmitter neck remains exposed. The uncovered part
serves as a radiator and protects the electronics from overheating and excessive cooling.
‣ When using in potentially explosive atmospheres, observe the information in the device-specific
Ex documentation. For detailed information on the temperature tables, see the separate
document entitled "Safety Instructions" (XA) for the device.
Vibrations The high oscillation frequency of the measuring tubes ensures that the correct operation of the
measuring system is not influenced by plant vibrations.
58 Endress+Hauser
Mechanical construction
Dimensions in SI units Compact version
A G
B C
K
D
L M
A0033787
Order code for "Housing", option A "Compact, aluminum, coated"

1) 1)
DN A B C D E 2) 3) F 2) 3) G K L M
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
4)
8 148 94 54 75 185 260 136 5.35 70
4)
15 148 94 54 75 185 260 136 8.30 70
4)
25 148 94 54 75 185 260 136 12.0 70
4)
40 148 94 54 105 189.5 294.5 136 17.6 79
4)
50 148 94 54 141 199.5 340.5 136 26.0 99
4)
80 148 94 54 200 219.5 419.5 136 40.5 139
4)
100 148 94 54 254 238 492 136 51.2 176
4)
150 148 94 54 378 259 637 136 68.9 218
4)
250 148 94 54 548 302.5 850.5 136 102.3 305
1) Depending on the cable gland used: values up to + 30 mm

2) With order code for "Sensor option", option CG or order code for "Measuring tube material", option SD, SE,
SF, TH: values +70 mm
3) If using a display, order code for "Display; operation", option B: values +28 mm
4) Depending on respective process connection→  61
Order code for "Housing", option B "Compact hygienic, stainless"

1) 1)
DN A B C D E 2) 3) F 2) 3) G K L M
4)
8 137 78 59 75 180 255 134 5.35 70
4)
15 137 78 59 75 180 255 134 8.30 70
4)
25 137 78 59 75 180 255 134 12.0 70
4)
40 137 78 59 105 184.5 289.5 134 17.6 79
4)
50 137 78 59 141 194.5 335.5 134 26.0 99
4)
80 137 78 59 200 214.5 414.5 134 40.5 139
4)
100 137 78 59 254 233 487 134 51.2 176
Endress+Hauser 59
1) 1)
DN A B C D E 2) 3) F 2) 3) G K L M
4)
150 137 78 59 378 254 632 134 68.9 218
4)
250 137 78 59 548 297.5 845.5 134 102.3 305

Order code for "Housing", option C "Ultra-compact hygienic, stainless"

1) 1)
DN A B C D F 2) 3) F 2) 3) G K L M
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
4)
8 124 68 56 75 180 255 112 5.35 70
4)
15 124 68 56 75 180 255 112 8.30 70
4)
25 124 68 56 75 180 255 112 12.0 70
4)
40 124 68 56 105 184.5 289.5 112 17.6 79
4)
50 124 68 56 141 194.5 335.5 112 26.0 99
4)
80 124 68 56 200 214.5 414.5 112 40.5 139
4)
100 124 68 56 254 233 487 112 51.2 176
4)
150 124 68 56 378 254 632 112 68.9 218
4)
250 124 68 56 548 297.5 845.5 112 102.3 305

60 Endress+Hauser
Flange connections
Fixed flange EN 1092-1, ASME B16.5, JIS B2220
C
A
B
E
D L
A0015621
Length tolerance for dimension L in mm:

• DN ≤ 100: +1.5 / –2.0
• DN ≥ 125: +3.5
Flange according to EN 1092-1 (DIN 2501): PN16

1.4404 (F316/F316L): order code for "Process connection", option D1S
Alloy C22: order code for "Process connection", option D1C
Flange with groove according to EN 1092-1 Form D (DIN 2512N): PN16

DN A B C D E L
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
100 220 180 8 × ⌀18 20 107.1 1 127/1 400 1)
150 285 240 8 × ⌀22 22 159.3 1 330/1 700 1)
250 405 355 12 × ⌀26 26 260.4 1 775
Surface roughness (flange): EN 1092-1 Form B1 (DIN 2526 Form C), Ra 3.2 to 12.5 µm
1) Installation length in accordance with NAMUR recommendation NE 132 optionally available (order code
for "Process connection", option D1N or D5N (with groove))
Flange according to EN 1092-1 (DIN 2501): PN16 with reduction in nominal diameter
1.4404 (F316/F316L
DN reduction Order code for A B C D E L

[mm] to DN "Process [mm] [mm] [mm] [mm] [mm] [mm]
[mm] connection",
option
100 80 DHS 220 180 8 × ⌀18 20 107.1 874
150 100 DJS 285 240 8 × ⌀22 22 159.3 1 167
200 150 DLS 340 295 12 × ⌀22 24 206.5 1 461
Endress+Hauser 61
Flange according to EN 1092-1 (DIN 2501): PN 40

Flange with groove according to EN 1092-1 Form D (DIN 2512N): PN 40

DN A B C D E L
8 1) 95 65 4 × ⌀14 16 17.3 370/510 2)
15 95 65 4 × ⌀14 16 17.3 404/510 2)
25 115 85 4 × ⌀14 18 28.5 440/600 2)
40 150 110 4 × ⌀18 18 43.1 550
50 165 125 4 × ⌀18 20 54.5 715/715 2)
80 200 160 8 × ⌀18 24 82.5 840/915 2)
100 235 190 8 × ⌀22 24 107.1 1 127
150 300 250 8 × ⌀26 28 159.3 1 370
250 450 385 12 × ⌀33 38 258.8 1 845
1) DN 8 with DN 15 flanges as standard

2) Installation length in accordance with NAMUR recommendation NE 132 optionally available (order code
for "Process connection", option D2N or D6N (with groove))
Flange according to EN 1092-1 (DIN 2501): PN 40 (with DN 25 flanges)

1.4404 (F316/F316L): order code for "Process connection", option R2S
DN A B C D E L
8 115 85 4 × ⌀14 18 28.5 440
15 115 85 4 × ⌀14 18 28.5 440
Flange according to EN 1092-1 (DIN 2501): PN 40 with reduction in nominal diameter

1.4404 (F316/F316L)

[mm] connection",
option
50 40 DFS 165 125 4 × ⌀18 20 54.5 555
80 50 DGS 200 160 8 × ⌀18 24 82.5 840
100 80 DIS 235 190 8 × ⌀22 24 107.1 874
150 100 DKS 300 250 8 × ⌀26 28 159.3 1 167
200 150 DMS 375 320 12 × ⌀30 34 206.5 1 461
62 Endress+Hauser


DN A B C D E L
50 180 135 4 × ⌀22 26 54.5 724
80 215 170 8 × ⌀22 28 81.7 875
100 250 200 8 × ⌀26 30 106.3 1 127
150 345 280 8 × ⌀33 36 157.1 1 410
250 470 400 12 × ⌀36 46 255.4 1 885
Surface roughness (flange):

EN 1092-1 Form B1 (DIN 2526 Form C), Ra 3.2 to 12.5 µm EN 1092-1 Form B2 (DIN 2526 Form E), Ra
0.8 to 3.2 µm


DN A B C D E L
8 1) 105 75 4 × ⌀14 20 17.3 400
15 105 75 4 × ⌀14 20 17.3 420
25 140 100 4 × ⌀18 24 28.5 470
40 170 125 4 × ⌀22 26 42.5 590
50 195 145 4 × ⌀26 28 53.9 740
80 230 180 8 × ⌀26 32 80.9 885
100 265 210 8 × ⌀30 36 104.3 1 127
150 355 290 12 × ⌀33 44 154.0 1 450
Surface roughness (flange): EN 1092-1 Form B2 (DIN 2526 Form E), Ra 0.8 to 3.2 µm


DN A B C D E L
250 505 430 12 × ⌀39 60 248.0 1 949
Surface roughness (flange): EN 1092-1 Form B2 (DIN 2526 Form E), Ra 0.8 to 3.2 µm
Endress+Hauser 63
Flange according to ASME B16.5: Class 150

1.4404 (F316/F316L): order code for "Process connection", option AAS
Alloy C22: order code for "Process connection", option AAC
DN A B C D E L
8 1) 90 60.3 4 × ⌀15.7 11.2 15.7 370
15 90 60.3 4 × ⌀15.7 11.2 15.7 404
25 110 79.4 4 × ⌀15.7 14.2 26.7 440
40 125 98.4 4 × ⌀15.9 15.9 40.9 550
50 150 120.7 4 × ⌀19.1 19.1 52.6 715
80 190 152.4 4 × ⌀19.1 23.9 78.0 840
100 230 190.5 8 × ⌀19.1 23.9 102.4 1 127
150 280 241.3 8 × ⌀22.4 25.4 154.2 1 398
250 405 362 12 × ⌀25.4 30.2 254.5 1 832
Surface roughness (flange): Ra 3.2 to 6.3 µm
Flange according to ASME B16.5: Class 150 with reduction in nominal diameter
1.4404 (F316/F316L)

[mm] connection",
option
50 40 AHS 150 120.7 4 × ⌀19.1 19.1 52.6 550
80 50 AJS 190 152.4 4 × ⌀19.1 23.9 78.0 720
100 80 ALS 230 190.5 8 × ⌀19.1 23.9 102.4 874
150 100 ANS 280 241.3 8 × ⌀22.4 25.4 154.2 1 167
200 150 APS 345 298.5 8 × ⌀22.4 29 202.7 1 461

1.4404 (F316/F316L): order code for "Process connection", option ABS
Alloy C22: order code for "Process connection", option ABC
DN A B C D E L
8 1) 95 66.7 4 × ⌀15.7 14.2 15.7 370
15 95 66.7 4 × ⌀15.7 14.2 15.7 404
25 125 88.9 4 × ⌀19.1 17.5 26.7 440
40 155 114.3 4 × ⌀22.3 20.6 40.9 550
50 165 127 8 × ⌀19.1 22.3 52.6 715
80 210 168.3 8 × ⌀22.3 28.4 78.0 840
100 255 200 8 × ⌀22.3 31.7 102.4 1 127
150 320 269.9 12 × ⌀22.3 36.5 154.2 1 417
250 445 387.4 16 × ⌀28.4 47.4 254.5 1 863
64 Endress+Hauser
1.4404 (F316/F316L)

[mm] connection",
option
50 40 AIS 165 127 8 × ⌀19.1 22.3 52.6 615
80 50 AKS 210 168.3 8 × ⌀22.3 28.4 78.0 732
100 80 AMS 255 200 8 × ⌀22.3 31.7 102.4 894
150 100 AOS 320 269.9 12 × ⌀22.3 36.5 154.2 1 187
200 150 AQS 380 330.2 12 × ⌀25.4 41.7 202.7 1 461

1.4404 (F316/F316L): order code for "Process connection", option ACS
Alloy C22: order code for "Process connection", option ACC
DN A B C D E L
8 1) 95 66.7 4 × ⌀15.7 20.6 13.9 400
15 95 66.7 4 × ⌀15.7 20.6 13.9 420
25 125 88.9 4 × ⌀19.1 23.9 24.3 490
40 155 114.3 4 × ⌀22.3 28.7 38.1 600
50 165 127 8 × ⌀19.1 31.8 49.2 742
80 210 168.3 8 × ⌀22.3 38.2 73.7 900
100 275 215.9 8 × ⌀25.4 48.4 97.3 1 157
150 355 292.1 12 × ⌀28.4 47.8 154.2 1 467
250 510 431.8 16 × ⌀35.1 69.9 254.5 1 946
Flange JIS B2220: 10K

1.4404 (F316/F316L): order code for "Process connection", option NDS
Alloy C22: order code for "Process connection", option NDC
DN A B C D E L
50 155 120 4 × ⌀19 16 50 715
80 185 150 8 × ⌀19 18 80 832
100 210 175 8 × ⌀19 18 100 1 127
150 280 240 8 × ⌀23 22 150 1 354
250 400 355 12 × ⌀25 24 250 1 775
Endress+Hauser 65

1.4404 (F316/F316L): order code for "Process connection", option NES
Alloy C22: order code for "Process connection", option NEC
DN A B C D E L
8 1) 95 70 4 × ⌀15 14 15 370
15 95 70 4 × ⌀15 14 15 404
25 125 90 4 × ⌀19 16 25 440
40 140 105 4 × ⌀19 18 40 550
50 155 120 8 × ⌀19 18 50 715
80 200 160 8 × ⌀23 22 80 832
100 225 185 8 × ⌀23 24 100 1 127
150 305 260 12 × ⌀25 28 150 1 386
250 430 380 12 × ⌀27 34 250 1 845

1.4404 (F316/F316L): order code for "Process connection", option NGS
Alloy C22: order code for "Process connection", option NGC
DN A B C D E L
8 1) 115 80 4 × ⌀19 20 15 400
15 115 80 4 × ⌀19 20 15 425
25 130 95 4 × ⌀19 22 25 485
40 160 120 4 × ⌀23 24 38 600
50 165 130 8 × ⌀19 26 50 760
80 210 170 8 × ⌀23 32 75 890
100 250 205 8 × ⌀25 36 100 1 167
150 355 295 12 × ⌀33 44 150 1 498

1.4404 (F316/F316L): order code for "Process connection", option NHS
Alloy C22: order code for "Process connection", option NHC
DN A B C D E L
8 1) 120 85 4 × ⌀19 23 12 420
15 120 85 4 × ⌀19 23 12 440
25 140 100 4 × ⌀23 27 22 494
40 175 130 4 × ⌀25 32 35 620
50 185 145 8 × ⌀23 34 48 775
80 230 185 8 × ⌀25 40 73 915
100 270 220 8 × ⌀27 44 98 1 167
66 Endress+Hauser

1.4404 (F316/F316L): order code for "Process connection", option NHS
Alloy C22: order code for "Process connection", option NHC
DN A B C D E L
150 365 305 12 × ⌀33 54 146 1 528
Endress+Hauser 67
Fixed flange DIN 11864-2
X X
C
A
B
E
D
L
A0015627
 38 Detail X: Asymmetrical process connection; the part shown in blue is provided by the supplier.

+1.5 / –2.0
Flange DIN11864-2 Form A, for pipe according to DIN11866 series A, flat with notch
1.4404 (316/316L)
Order code for "Process connection", option KCS
DN A B C D E L
8 54 37 4 × ⌀9 10 10 387
15 59 42 4 × ⌀9 10 16 418
25 70 53 4 × ⌀9 10 26 454
40 82 65 4 × ⌀9 10 38 560
50 94 77 4 × ⌀9 10 50 720
80 133 112 8 × ⌀11 12 81 900
100 159 137 8 × ⌀11 14 100 1 127
3A version available: order code for "Additional approval", option LP in conjunction with
Ramax = 0.76 µm: order code for "Measuring tube material", option SB, SE or
Ramax = 0.38 µm: order code for "Measuring tube material", option SC, SF
Ramax = 0.38 µm electropolished: order code for "Measuring tube material", option BC
68 Endress+Hauser
Lap joint flange EN 1092-1, ASME B16.5, JIS B2220
C
A
B
E
F
D L
A0022221

+1.5 / –2.0
Lap joint flange according to EN 1092-1 Form D: PN 40

1.4301 (F304), wetted parts Alloy C22
Order code for "Process connection", option DAC
DN A B C D E F L Ldiff 1)
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
8 2) 95 65 4 × ⌀14 14.5 45 17.3 370 0
15 95 65 4 × ⌀14 14.5 45 17.3 404 0
25 115 85 4 × ⌀14 16.5 68 28.5 444 +4
40 150 110 4 × ⌀18 21 88 43.1 560 +10
50 165 125 4 × ⌀18 23 102 54.5 719 +4
80 200 160 8 × ⌀18 29 138 82.5 848 +8
100 235 190 8 × ⌀22 34 162 107.1 1 131 +4
1) Difference to installation length of the welding neck flange (order code for "Process connection", option
D2C)
Lap joint flange according to ASME B16.5: Class 150

Order code for "Process connection", option ADC
8 2) 90 60.3 4 × ⌀ 15.7 15 35.1 15.7 370 0
15 90 60.3 4 × ⌀ 15.7 15 35.1 15.7 404 0
25 110 79.4 4 × ⌀ 15.7 16 50.8 26.7 440 0
40 125 98.4 4 × ⌀ 15.7 15.9 73.2 40.9 550 0
50 150 120.7 4 × ⌀ 19.1 19 91.9 52.6 715 0
80 190 152.4 4 × ⌀ 19.1 22.3 127.0 78.0 840 0
Endress+Hauser 69

100 230 190.5 8 × ⌀ 19.1 26 157.2 102.4 1 127 0
AAC)

Order code for "Process connection", option AEC
8 2) 95 66.7 4 × ⌀ 15.7 16.5 35.1 15.7 376 +6
15 95 66.7 4 × ⌀ 15.7 16.5 35.1 15.7 406 +2
25 125 88.9 4 × ⌀ 19.1 21.0 50.8 26.7 450 +10
40 155 114.3 4 × ⌀ 22.3 23.0 73.2 40.9 564 +14
50 165 127 8 × ⌀ 19.1 25.5 91.9 52.6 717 +2
80 210 168.3 8 × ⌀ 22.3 31.0 127.0 78.0 852.6 +12.6
100 255 200 8 × ⌀ 22.3 32.0 157.2 102.4 1 139 +12
ABC)

Order code for "Process connection", option AFC
8 2) 95 66.7 4 × ⌀ 15.7 17.0 35.1 13.9 400 0
15 95 66.7 4 × ⌀ 15.7 17.0 35.1 13.9 420 0
25 125 88.9 4 × ⌀ 19.1 21.5 50.8 24.3 490 0
40 155 114.3 4 × ⌀ 22.3 25.0 73.2 38.1 600 0
50 165 127 8 × ⌀ 19.1 28.0 91.9 49.2 742 0
80 210 168.3 8 × ⌀ 22.3 35.0 127.0 73.7 900 0
100 275 215.9 8 × ⌀ 25.4 44.0 157.2 97.3 1 167 +10
ACC)
70 Endress+Hauser
Lap joint flange JIS B2220: 20K

Order code for "Process connection", option NIC
8 2) 95 70 4 × ⌀ 15 14 51 15 370 0
15 95 70 4 × ⌀ 15 14 51 15 404 0
25 125 90 4 × ⌀ 19 18.5 67 25 440 0
40 140 105 4 × ⌀ 19 18.5 81 40 550 0
50 155 120 8 × ⌀ 19 23 96 50 715 0
80 200 160 8 × ⌀ 23 29 132 80 844 +12
100 225 185 8 × ⌀ 23 29 160 100 1 127 0
NEC)
Endress+Hauser 71
Clamp connections
Tri-Clamp
B
L
A0015625

+1.5 / –2.0
Tri-Clamp (½"), for pipe according to DIN 11866 series C

1.4404 (316/316L)
Order code for "Process connection", option FDW
DN Clamp A B L
[mm] [in] [mm] [mm] [mm]
8 ½ 25.0 9.5 367
15 ½ 25.0 9.5 398
3-A version available: order code for "Additional approval", option LP in conjunction with
Tri-Clamp ( ≥ 1"), for pipe according to DIN 11866 series C

1.4404 (316/316L)
Order code for "Process connection", option FTS
DN Clamp A B L
[mm] [in] [mm] [mm] [mm]
8 1 50.4 22.1 367
15 1 50.4 22.1 398
25 1 50.4 22.1 434
40 1½ 50.4 34.8 560
50 2 63.9 47.5 720
80 3 90.9 72.9 900
100 4 118.9 97.4 1 127
72 Endress+Hauser
Threaded couplings
Thread DIN 11851, DIN11864-1, SMS 1145
A
B
L
A0015628

+1.5 / –2.0
Thread DIN 11851, for pipe according to DIN11866, series A

1.4404 (316/316L)
Order code for "Process connection", option FMW
DN A B L
[mm] [in] [mm] [mm]
8 Rd 34 × ¹⁄₈ 16 367
15 Rd 34 × ¹⁄₈ 16 398
25 Rd 52 × ¹⁄₆ 26 434
40 Rd 65 × ¹⁄₆ 38 560
50 Rd 78 × ¹⁄₆ 50 720
80 Rd 110 × ¹⁄₄ 81 900
100 Rd 130 × ¹⁄₄ 100 1 127
Ramax = 0.76 µm: order code for "Measuring tube material", option SB, SE
Thread DIN11864-1 Form A, for pipe according to DIN11866, series A

1.4404 (316/316L)
Order code for "Process connection", option FLW
DN A B L
[mm] [in] [mm] [mm]
8 Rd 28 × ¹⁄₈ 10 367
15 Rd 34 × ¹⁄₈ 16 398
25 Rd 52 × ¹⁄₈ 26 434
40 Rd 65 × ¹⁄₆ 38 560
50 Rd 78 × ¹⁄₆ 50 720
80 Rd 110 × ¹⁄₄ 81 900
100 Rd 130 × ¹⁄₄ 100 1 127
Endress+Hauser 73
Thread SMS 1145

1.4404 (316/316L)
Order code for "Process connection", option SCS
DN A B L
[mm] [in] [mm] [mm]
8 Rd 40 × ¹⁄₆ 22.6 367
15 Rd 40 × ¹⁄₆ 22.6 398
25 Rd 40 × ¹⁄₆ 22.6 434
40 Rd 60 × ¹⁄₆ 35.6 560
50 Rd 70 × ¹⁄₆ 48.6 720
80 Rd 98 × ¹⁄₆ 72.9 900
100 Rd 132 × ¹⁄₆ 97.6 1 127
Ramax = 0.76 µm: order code for "Measuring tube material", option SB, SE
74 Endress+Hauser
Thread ISO 2853
A
B
L
A0015623

+1.5 / –2.0
Thread ISO 2853, for pipe according to ISO 2037

1.4404 (316/316L)
Order code for "Process connection", option JSF
DN A 1) B L
[mm] [mm] [mm] [mm]
8 37.13 22.6 367
15 37.13 22.6 398
25 37.13 22.6 434
40 52.68 35.6 560
50 64.16 48.6 720
80 91.19 72.9 900
100 118.21 97.6 1 127
1) Max. thread diameter as per ISO 2853 annex A
Endress+Hauser 75
VCO
B
L
A0015624

+1.5 / –2.0
8-VCO-4 (½")
1.4404 (316/316L)
Order code for "Process connection", option CVS
DN A B L
[mm] [in] [mm] [mm]
8 AF 1 10.2 390
12-VCO-4 (¾")
1.4404 (316/316L)
Order code for "Process connection", option CWS
DN A B L
[mm] [in] [mm] [mm]
15 AF 1½ 15.7 430
76 Endress+Hauser

Top-hat rail EN 60715:
• TH 35 x 7.5
• TH 35 x 15
C
B D
A0016777
A B C D
[mm] [mm] [mm] [mm]
108 114.5 99 22.5
Endress+Hauser 77
Accessories
Rupture disk/purge connections
DN 8 (!⁄#")...150 (6") DN 250 (10")
1 1;2 1 1;2
45°
A
L L A
35 (1.38) ca. 75 (approx. 2.95)

SW 1"
½" NPT
½" NPT
1 2
A0028914
 39
1 Connection nipple for purge connections: order code for "Sensor options", option CH "Purge connection"
2 Connection nipple with rupture disk: order code for "Sensor option", option CA "Rupture disk"
DN A L
[mm] [mm] [mm]
8 62 216
15 62 220
25 62 260
40 67 310
50 79 452
80 101 560
100 120 684
150 141 880
250 182 380
78 Endress+Hauser
Dimensions in US units Compact version
A G
B C
K
D
L M
A0033787

DN A 1) B 1) C D F 2) 3) F 2) 3) G K L M
[in] [in] [in] [in] [in] [in] [in] [in] [in] [in] [in]
4)
³⁄₈ 5.83 3.70 2.13 2.95 7.28 10.24 5.35 0.211 2.76
4)
½ 5.83 3.70 2.13 2.95 7.28 10.24 5.35 0.33 2.76
4)
1 5.83 3.70 2.13 2.95 7.28 10.24 5.35 0.47 2.76
4)
1½ 5.83 3.70 2.13 4.13 7.46 11.59 5.35 0.69 3.11
4)
2 5.83 3.70 2.13 5.55 7.85 13.41 5.35 1.02 3.90
4)
3 5.83 3.70 2.13 7.87 8.64 16.52 5.35 1.59 5.47
4)
4 5.83 3.70 2.13 10 9.37 19.37 5.35 2.02 6.93
4)
6 5.83 3.70 2.13 14.88 10.2 25.08 5.35 2.71 8.58
4)
10 5.83 3.70 2.13 21.57 11.91 33.48 5.35 4.03 12.01
1) Depending on the cable gland used: values up to + 1.18 in

SF, TH: values +2.76 in
3) If using a display, order code for "Display; operation", option B: values +1.1 in

DN A 1) B C D F 2) 3) F 2) 3) G K L M
4)
³⁄₈ 5.39 3.07 2.32 2.95 7.09 10.04 5.28 0.211 2.76
4)
½ 5.39 3.07 2.32 2.95 7.09 10.04 5.28 0.33 2.76
4)
1 5.39 3.07 2.32 2.95 7.09 10.04 5.28 0.47 2.76
4)
1½ 5.39 3.07 2.32 4.13 7.26 11.4 5.28 0.69 3.11
4)
2 5.39 3.07 2.32 5.55 7.66 13.21 5.28 1.02 3.90
4)
3 5.39 3.07 2.32 7.87 8.44 16.32 5.28 1.59 5.47
4)
4 5.39 3.07 2.32 10 9.17 19.17 5.28 2.02 6.93
Endress+Hauser 79
DN A 1) B C D F 2) 3) F 2) 3) G K L M
4)
6 5.39 3.07 2.32 14.88 10 24.88 5.28 2.71 8.58
4)
10 5.39 3.07 2.32 21.57 11.71 33.29 5.28 4.03 12.01
1) Depending on the cable gland used: values up to +1.18 in

Order code for "Housing", option C "Ultra-compact hygienic, stainless"

DN A 1) B C D F 2) 3) F 2) 3) G K L M
4)
³⁄₈ 4.88 2.68 2.20 2.95 7.09 10.04 4.41 0.21 2.76
4)
½ 4.88 2.68 2.20 2.95 7.09 10.04 4.41 0.33 2.76
4)
1 4.88 2.68 2.20 2.95 7.09 10.04 4.41 0.47 2.76
4)
1½ 4.88 2.68 2.20 4.13 7.26 11.4 4.41 0.69 3.11
4)
2 4.88 2.68 2.20 5.55 7.66 13.21 4.41 1.02 3.90
4)
3 4.88 2.68 2.20 7.87 8.44 16.32 4.41 1.59 5.47
4)
4 4.88 2.68 2.20 10 9.17 19.17 4.41 2.02 6.93
4)
6 4.88 2.68 2.20 14.88 10 24.88 4.41 2.71 8.58
4)
10 4.88 2.68 2.20 21.57 11.71 33.29 4.41 4.03 12.01
1) Depending on the cable gland used: values up to +1.18 in

80 Endress+Hauser
Flange connections
Fixed flange ASME B16.5
C
A
B
E
D L
A0015621
Length tolerance for dimension L in inch:

• DN ≤ 4": +0.06 / –0.08
• DN ≥ 5": +0.14

1.4404 (F316/F316L): order code for "Process connection", option AAS
Alloy C22: order code for "Process connection", option AAC
DN A B C D E L
[in] [in] [in] [in] [in] [in] [in]
³⁄₈ 1) 3.54 2.37 4 × ⌀0.62 0.44 0.62 14.57
½ 3.54 2.37 4 × ⌀0.62 0.44 0.62 15.91
1 4.33 3.13 4 × ⌀0.62 0.56 1.05 17.32
1½ 4.92 3.87 4 × ⌀0.63 0.63 1.61 21.65
2 5.91 4.75 4 × ⌀0.75 0.75 2.07 28.15
3 7.48 6.00 4 × ⌀0.75 0.94 3.07 33.07
4 9.06 7.50 8 × ⌀0.75 0.94 4.03 44.37
6 11.02 9.50 8 × ⌀0.88 1 6.07 55.04
10 15.94 14.25 12 × ⌀1.0 1.19 10.02 72.13
Surface roughness (flange): Ra 126 to 248 µin
1) DN ³⁄₈" with DN ½" flanges as standard
1.4404 (F316/F316L)

[in] to DN "Process [in] [in] [in] [in] [in] [in]
[in] connection",
option
2 1½ AHS 5.91 4.75 4 × ⌀0.75 0.75 2.07 21.65
3 2 AJS 7.48 6 4 × ⌀0.75 0.94 3.07 28.35
4 3 ALS 9.06 7.5 8 × ⌀0.75 0.94 4.03 34.41
6 4 ANS 11.02 9.5 8 × ⌀0.88 1 6.07 45.94
8 6 APS 13.58 11.75 8 × ⌀0.88 1.14 7.98 57.52
Endress+Hauser 81

1.4404 (F316/F316L): order code for "Process connection", option ABS
Alloy C22: order code for "Process connection", option ABC
DN A B C D E L
³⁄₈ 1) 3.74 2.63 4 × ⌀0.62 0.56 0.62 14.57
½ 3.74 2.63 4 × ⌀0.62 0.56 0.62 15.91
1 4.92 3.50 4 × ⌀0.75 0.69 1.05 17.32
1½ 6.10 4.50 4 × ⌀0.88 0.81 1.61 21.65
2 6.50 5.00 8 × ⌀0.75 0.88 2.07 28.15
3 8.27 6.63 8 × ⌀0.88 1.12 3.07 33.07
4 10.04 7.87 8 × ⌀0.88 1.25 4.03 44.37
6 12.6 10.63 12 × ⌀0.88 1.44 6.07 55.79
10 17.52 15.25 16 × ⌀1.12 1.87 10.02 73.35
1.4404 (F316/F316L)

[in] to DN "Process [in] [in] [in] [in] [in] [in]
[in] connection",
option
2 1½ AIS 6.5 5 8 × ⌀0.75 0.88 2.07 24.21
3 2 AKS 8.27 6.63 8 × ⌀0.88 1.12 3.07 28.82
4 3 AMS 10.04 7.87 8 × ⌀0.88 1.25 4.03 35.2
6 4 AOS 12.6 10.63 12 × ⌀0.88 1.44 6.07 46.73
8 6 AQS 14.96 13 12 × ⌀1 1.64 7.98 57.52

1.4404 (F316/F316L): order code for "Process connection", option ACS
Alloy C22: order code for "Process connection", option ACC
DN A B C D E L
³⁄₈ 1) 3.74 2.63 4 × ⌀0.62 0.81 0.55 15.75
½ 3.74 2.63 4 × ⌀0.62 0.81 0.55 16.54
1 4.92 3.50 4 × ⌀0.75 0.94 0.96 19.29
1½ 6.10 4.50 4 × ⌀0.88 1.13 1.5 23.62
2 6.50 5.00 8 × ⌀0.75 1.25 1.94 29.21
3 8.27 6.63 8 × ⌀0.88 1.5 2.9 35.43
4 10.83 8.50 8 × ⌀1.00 1.91 3.83 45.55
6 13.98 11.50 12 × ⌀1.12 1.88 6.07 57.76
10 20.08 17.00 16 × ⌀1.38 2.75 10.02 76.61
82 Endress+Hauser
Lap joint flange ASME B16.5
C
A
B
E
F
D L
A0022221

+0.06 / –0.08

[in] [in] [in] [in] [in] [in] [in] [in] [in]
³⁄₈ 2) 3.54 2.37 4 × ⌀ 0.62 0.59 1.38 0.62 14.57 0
½ 3.54 2.37 4 × ⌀ 0.62 0.59 1.38 0.62 15.91 0
1 4.33 3.13 4 × ⌀ 0.62 0.63 2 1.05 17.32 0
1½ 4.92 3.87 4 × ⌀ 0.62 0.63 2.88 1.61 21.65 0
2 5.91 4.75 4 × ⌀ 0.75 0.75 3.62 2.07 28.15 0
3 7.48 6.00 4 × ⌀ 0.75 0.88 5 3.07 33.07 0
4 9.06 7.50 8 × ⌀ 0.75 1.02 6.19 4.03 44.37 0
AAC)

³⁄₈ 2) 3.74 2.63 4 × ⌀ 0.62 0.65 1.38 0.62 14.8 +0.23
½ 3.74 2.63 4 × ⌀ 0.62 0.65 1.38 0.62 15.98 +0.07
1 4.92 3.50 4 × ⌀ 0.75 0.83 2 1.05 17.72 +0.40
1½ 6.10 4.50 4 × ⌀ 0.88 0.91 2.88 1.61 22.2 +0.55
2 6.50 5.00 8 × ⌀ 0.75 1 3.62 2.07 28.23 +0.08
3 8.27 6.63 8 × ⌀ 0.88 1.22 5 3.07 33.57 +0.50
Endress+Hauser 83

4 10.04 7.87 8 × ⌀ 0.88 1.26 6.19 4.03 44.84 +0.47
AAC)
Lap joint flange according to ASME B16.5, Class 600

Order code for "Process connection", option AFC
³⁄₈ 2) 3.74 2.63 4 × ⌀ 0.62 0.67 1.38 0.55 15.75 0
½ 3.74 2.63 4 × ⌀ 0.62 0.67 1.38 0.55 16.54 0
1 4.92 3.50 4 × ⌀ 0.75 0.85 2 0.96 19.29 0
1½ 6.10 4.50 4 × ⌀ 0.88 0.98 2.88 1.5 23.62 0
2 6.50 5.00 8 × ⌀ 0.75 1.1 3.62 1.94 29.21 0
3 8.27 6.63 8 × ⌀ 0.88 1.38 5 2.9 35.43 0
4 10.83 8.50 8×⌀1 1.73 6.19 3.83 45.94 +0.39
AAC)
84 Endress+Hauser
Clamp connections
Tri-Clamp
B
L
A0015625

+0.06 / –0.08
Tri-Clamp (½"), DIN 11866 series C

1.4404 (316/316L)
Order code for "Process connection", option FDW
DN Clamp A B L
[in] [in] [in] [in] [in]
³⁄₈ ½ 0.98 0.37 14.4
½ ½ 0.98 0.37 15.7
Ramax = 30 µin: order code for "Measuring tube material", option SB, SE or
Ramax = 15 µin: order code for "Measuring tube material", option SC, SF
Ramax = 15 µin electropolished: order code for "Measuring tube material", option BC
Tri-Clamp ( ≥ 1"), DIN 11866 series C

1.4404 (316/316L)
Order code for "Process connection", option FTS
DN Clamp A B L
[in] [in] [in] [in] [in]
³⁄₈ 1 1.98 0.87 14.4
½ 1 1.98 0.87 15.7
1 1 1.98 0.87 17.1
1½ 1½ 1.98 1.37 22.0
2 2 2.52 1.87 28.3
3 3 3.58 2.87 35.4
4 4 4.68 3.83 44.4
Ramax = 30 µin: order code for "Measuring tube material", option SB, SE or
Ramax = 15 µin: order code for "Measuring tube material", option SC, SF
Ramax = 15 µin electropolished: order code for "Measuring tube material", option BC
Endress+Hauser 85
Threaded couplings
Thread SMS 1145
A
B
L
A0015628

+0.06 / –0.08
Thread SMS 1145

1.4404 (316/316L)
Order code for "Process connection", option SCS
DN A B L
[in] [in] [in] [in]
³⁄₈ Rd 40 × ¹⁄₆ 0.89 14.45
½ Rd 40 × ¹⁄₆ 0.89 15.67
1 Rd 40 × ¹⁄₆ 0.89 17.09
1½ Rd 60 × ¹⁄₆ 1.4 22.05
2 Rd 70 × ¹⁄₆ 1.91 28.35
3 Rd 98 × ¹⁄₆ 2.87 35.43
4 Rd 132 × ¹⁄₆ 3.84 44.37
Ramax = 30 µin: order code for "Measuring tube material", option SB, SE
86 Endress+Hauser
VCO
B
L
A0015624

+0.06 / –0.08
8-VCO-4 (½")
1.4404 (316/316L)
Order code for "Process connection", option CVS
DN A B L
[in] [in] [in] [in]
³⁄₈ AF 1 0.4 15.35
12-VCO-4 (¾")
1.4404 (316/316L)
Order code for "Process connection", option CWS
DN A B L
[in] [in] [in] [in]
½ AF 1½ 0.62 16.93

Top-hat rail EN 60715:
• TH 35 x 7.5
• TH 35 x 15
A
B D
A0016777
A B C D
[in] [in] [in] [in]
4.25 4.51 3.9 0.89
Endress+Hauser 87
Accessories
Rupture disk/purge connections
DN 8 (!⁄#")...150 (6") DN 250 (10")
1 1;2 1 1;2
45°
A
L L A
35 (1.38) ca. 75 (approx. 2.95)

SW 1"
½" NPT
½" NPT
1 2
A0028914
1 Connection nipple for purge connections: order code for "Sensor options", option CH "Purge connection"
2 Connection nipple with rupture disk: order code for "Sensor option", option CA "Rupture disk"
DN A L
[in] [in] [in]
³⁄₈ 2.44 8.50
½ 2.44 8.66
1 2.44 10.24
1½ 2.64 12.20
2 3.11 17.78
3 3.98 22.0
4 4.72 27.0
6 5.55 34.6
10 7.17 14.96
Weight All values (weight exclusive of packaging material) refer to devices with EN/DIN PN 40 flanges.
Weight specifications including transmitter: order code for "Housing", option A "Compact, aluminum
coated".
Different values due to different transmitter versions:
Weight in SI units
DN [mm] Weight [kg]
8 9
15 10
25 12
40 17
50 28
80 53
100 94
88 Endress+Hauser
DN [mm] Weight [kg]
150 152
250 398
Weight in US units
DN [in] Weight [lbs]
3/8 20
½ 22
1 26
1½ 37
2 62
3 117
4 207
6 335
10 878

49 g (1.73 ounce)
Materials Transmitter housing

• Order code for "Housing", option A "Compact, aluminum coated":
Aluminum, AlSi10Mg, coated
• Order code for "Housing", option B "Compact, hygienic, stainless":
Hygienic version, for maximum corrosion resistance: stainless steel 1.4404 (316L)
• Order code for "Housing", option C "Ultra-compact, hygienic, stainless":
Hygienic version, for maximum corrosion resistance: stainless steel 1.4404 (316L)
• Window material for optional local display (→  92):
• For order code for "Housing", option A: glass
• For order code for "Housing", option B and C: plastic
Cable entries/cable glands
3
A0020640
 40 Possible cable entries/cable glands

1 Female thread M20 × 1.5
2 Cable gland M20 × 1.5
3 Adapter for cable entry with internal thread G ½" or NPT ½"
Endress+Hauser 89

The various cable entries are suitable for hazardous and non-hazardous areas.
Cable entry/cable gland Material
Cable gland M20 × 1.5
Adapter for cable entry with internal thread G ½" Nickel-plated brass
Adapter for cable entry with internal thread NPT ½"

The various cable entries are suitable for hazardous and non-hazardous areas.
Cable entry/cable gland Material
Cable gland M20 × 1.5 Stainless steel, 1.4404 (316L)
Adapter for cable entry with internal thread G ½"
Adapter for cable entry with internal thread NPT ½"
Device plug
Electrical connection Material
Plug M12x1 • Socket: Stainless steel, 1.4404 (316L)

• Contact housing: Polyamide
• Contacts: Gold-plated brass
Sensor housing
The material of the sensor housing depends on the option selected in the order code for
"Measuring tube mat., wetted surface".
Order code for "Measuring tube mat., wetted Material

surface"
Option HA, SA, SD, TH • Acid and alkali-resistant outer surface

• Stainless steel 1.4301 (304)
 "316L
With order code for "Sensor option", option CC
Sensor housing": stainless steel, 1.4404
(316L)
Option SB, SC, SE, SF • Acid and alkali-resistant outer surface

• Stainless steel 1.4301 (304)
Measuring tubes
• DN 8 to 100 (3/8…4"): stainless steel, 1.4539 (904L);
Manifold: stainless steel, 1.4404 (316/316L)
• DN 150 (6"), DN 250 (10"): stainless steel, 1.4404 (316/316L);
Manifold: stainless steel, 1.4404 (316/316L)
• DN 8 to 250 (3/8 to 10"): Alloy C22, 2.4602 (UNS N06022);
Manifold: Alloy C22, 2.4602 (UNS N06022)
90 Endress+Hauser
Process connections
• Flanges according to EN 1092-1 (DIN2501) / according to ASME B 16.5 / as per JIS B2220:
• Stainless steel, 1.4404 (F316/F316L)
• Alloy C22, 2.4602 (UNS N06022)
• Lap joint flanges: stainless steel, 1.4301 (F304); wetted parts Alloy C22
• All other process connections:
Stainless steel, 1.4404 (316/316L)
Available process connections→  91
Seals
Welded process connections without internal seals

Housing: Polyamide
Process connections • Fixed flange connections:

• EN 1092-1 (DIN 2501) flange
• EN 1092-1 (DIN 2512N) flange
• Namur lengths in accordance with NE 132
• ASME B16.5 flange
• JIS B2220 flange
• DIN 11864-2 Form A flange, DIN 11866 series A, flange with notch
• Clamp connections:
Tri-Clamp (OD tubes), DIN 11866 series C
• Thread:
• DIN 11851 thread, DIN 11866 series A
• SMS 1145 thread
• ISO 2853 thread, ISO 2037
• DIN 11864-1 Form A thread, DIN 11866 series A
• VCO connections:
• 8-VCO-4
• 12-VCO-4
Process connection materials
Surface roughness All data relate to parts in contact with fluid. The following surface roughness quality can be ordered.
• Not polished
• Ramax = 0.76 µm (30 µin)
• Ramax = 0.38 µm (15 µin)
• Ramax = 0.38 µm (15 µin) electropolished
Operability
Operating concept Operator-oriented menu structure for user-specific tasks
• Commissioning
• Operation
• Diagnostics
• Expert level
Quick and safe commissioning
• Individual menus for applications
• Menu guidance with brief explanations of the individual parameter functions
Endress+Hauser 91
Reliable operation
• Operation in the following languages:
• Via "FieldCare", "DeviceCare" operating tool:
English, German, French, Spanish, Italian, Chinese, Japanese
• Via integrated Web browser(only available for device versions with HART, PROFIBUS DP,
PROFINET and EtherNet/IP):
English, German, French, Spanish, Italian, Dutch, Portuguese, Polish, Russian, Turkish, Chinese,
Japanese, Bahasa (Indonesian), Vietnamese, Czech, Swedish, Korean
• Uniform operating philosophy applied to operating tools and Web browser
• If replacing the electronic module, transfer the device configuration via the plug-in memory
(HistoROM DAT) which contains the process and measuring device data and the event logbook. No
need to reconfigure.
For devices with Modbus RS485, the data recovery function is implemented without the plug-in
memory (HistoROM DAT).
Efficient diagnostics increase measurement availability
• Troubleshooting measures can be called up via the operating tools and web browser
• Diverse simulation options
• Status indicated by several light emitting diodes (LEDs) on the electronic module in the housing
compartment
Local display A local display is only available for device versions with the following communication protocols:
HART, PROFIBUS-DP, PROFINET, EtherNet/IP
The local display is only available with the following device order code:
Order code for "Display; operation", option B: 4-line; illuminated, via communication
Display element
• 4-line liquid crystal display with 16 characters per line.
• White background lighting; switches to red in event of device errors.
• Format for displaying measured variables and status variables can be individually configured.
• Permitted ambient temperature for the display: –20 to +60 °C (–4 to +140 °F). The readability of
the display may be impaired at temperatures outside the temperature range.
Remote operation Via HART protocol

This communication interface is available in device versions with a HART output.
4 6
1 2 3 5
A0028747
 41 Options for remote operation via HART protocol

2 Field Communicator 475
3 Computer with operating tool (e.g. FieldCare, AMS Device Manager, SIMATIC PDM)
4 Commubox FXA195 (USB)
5 Field Xpert SFX350 or SFX370
6 VIATOR Bluetooth modem with connecting cable
7 Transmitter
Via PROFIBUS DP network

This communication interface is available in device versions with PROFIBUS DP.
92 Endress+Hauser
1 2
4 4 4
A0020903
 42 Options for remote operation via PROFIBUS DP network

1 Automation system
2 Computer with PROFIBUS network card
3 PROFIBUS DP network
4 Measuring device
Via EtherNet/IP network

This communication interface is available in device versions with EtherNet/IP.
Star topology
1 2 3
5 5 5
A0032078
 43 Options for remote operation via EtherNet/IP network: star topology

1 Automation system, e.g. "RSLogix" (Rockwell Automation)
2 Workstation for measuring device operation: with Custom Add-On Profile for "RSLogix 5000" (Rockwell
Automation) or with Electronic Data Sheet (EDS)
3 Computer with Web browser (e.g. Internet Explorer) for accessing the integrated device Web server or
computer with operating tool (e.g. FieldCare, DeviceCare) with COM DTM "CDI Communication TCP/IP"
4 Ethernet switch
5 Measuring device
Via PROFINET network

This communication interface is available in device versions with PROFINET.
Endress+Hauser 93
Star topology
1 3 2
4 4 4
A0026545
 44 Options for remote operation via PROFINET network: star topology

1 Automation system, e.g. Simatic S7 (Siemens)
2 Computer with Web browser (e.g. Internet Explorer) for accessing the integrated device Web server or
computer with operating tool (e.g. FieldCare, DeviceCare, SIMATIC PDM) with COM DTM "CDI Communication
TCP/IP"
3 Switch, e.g. Scalance X204 (Siemens)
4 Measuring device
Service interface Via service interface (CDI-RJ45)

This communication interface is present in the following device version:
• Order code for "Output", option B: 4-20 mA HART, pulse/frequency/switch output
• Order code for "Output", option L: PROFIBUS DP
• Order code for "Output", option N: EtherNet/IP
• Order code for "Output", option R: PROFINET
HART
1
A0016926
 45 Connection for the order code for "Output", option B: 4-20 mA HART, pulse/frequency/switch output
1 Service interface (CDI -RJ45) of the measuring device with access to the integrated Web server
2 Computer with Web browser (e.g. Internet Explorer) for accessing the integrated device Web server or with
"FieldCare" operating tool with COM DTM "CDI Communication TCP/IP"
3 Standard Ethernet connecting cable with RJ45 plug
94 Endress+Hauser
PROFIBUS DP
1
A0021270
 46 Connection for order code for "Output", option L: PROFIBUS DP

1 Service interface (CDI -RJ45) of the measuring device with access to the integrated Web server
EtherNet/IP
1
A0016940
 47 Connection for order code for "Output", option N: EtherNet/IP

1 Service interface (CDI -RJ45) and EtherNet/IP interface of the measuring device with access to the integrated
Web server
Endress+Hauser 95
PROFINET
1
A0016940
 48 Connection for order code for "Output", option R: PROFINET

1 Service interface (CDI -RJ45) and PROFINET interface of the measuring device with access to the integrated
Web server
Via service interface (CDI)

This communication interface is present in the following device version:
Order code for "Output", option M: Modbus RS485
Modbus RS485
2 1
A0030216
1 Service interface (CDI) of measuring device

2 Commubox FXA291
3 Computer with "FieldCare" operating tool with COM DTM "CDI Communication FXA291"
Certificates and approvals

CE mark The device meets the legal requirements of the applicable EU Directives. These are listed in the
corresponding EU Declaration of Conformity along with the standards applied.
Endress+Hauser confirms successful testing of the device by affixing to it the CE mark.
C-Tick symbol The measuring system meets the EMC requirements of the "Australian Communications and Media
Authority (ACMA)".
96 Endress+Hauser
Ex approval The measuring device is certified for use in hazardous areas and the relevant safety instructions are
provided in the separate "Safety Instructions" (XA) document. Reference is made to this document on
the nameplate.
The separate Ex documentation (XA) containing all the relevant explosion protection data is
available from your Endress+Hauser sales center.
ATEX/IECEx
Currently, the following versions for use in hazardous areas are available:
Ex ia
Category (ATEX) Type of protection
II1/2G Ex ia IIC T6…T1 Ga/Gb or Ex ia IIB T6…T1 Ga/Gb
II2G Ex ia IIC T6…T1 Gb or Ex ia IIB T6…T1 Gb
II1/2G, II2D Ex ia IIC T6…T1 Ga/Gb or Ex ia IIB T6…T1 Ga/Gb

Ex tb IIIC Txx °C Db
II2G, II2D Ex ia IIC T6…T1 Gb or Ex ia IIB T6…T1 Gb

Ex tb IIIC Txx °C Db
Ex nA
Category (ATEX) Type of protection
II3G Ex nA IIC T6…T1 Gc or Ex nA IIC T5-T1 Gc
CCSAUS
Currently, the following versions for use in hazardous areas are available:
IS (Ex i)
• Class I Division 1 Groups ABCD
• Class II Division 1 Groups EFG and Class III
NI (Ex nA)
Class I Division 2 Groups ABCD
Sanitary compatibility • 3-A approval

Only devices with the order code for "Additional approval", option LP "3A" have 3-A approval.
• EHEDG-tested
Only devices with the order code for "Additional approval", option LT "EHEDG" have been tested and
meet the requirements of the EHEDG.
To meet the requirements for EHEDG certification, the device must be used with process
connections in accordance with the EHEDG position paper entitled "Easy Cleanable Pipe Couplings
and Process Connections" (www.ehedg.org).
HART certification HART interface

The measuring device is certified and registered by the FieldComm Group. The measuring system
meets all the requirements of the following specifications:
• Certified according to HART 7
• The device can also be operated with certified devices of other manufacturers (interoperability)
Certification PROFIBUS PROFIBUS interface

The measuring device is certified and registered by the PNO (PROFIBUS User Organization
Organization). The measuring system meets all the requirements of the following specifications:
• Certified in accordance with PROFIBUS PA Profile 3.02
Endress+Hauser 97
Certification PROFINET PROFINET interface

The measuring device is certified and registered by the PNO (PROFIBUS User Organization
Organization). The measuring system meets all the requirements of the following specifications:
• Certified according to:
• Test specification for PROFINET devices
• PROFINET Security Level 1 – Netload Class
EtherNet/IP certification The measuring device is certified and registered by the ODVA (Open Device Vendor Association).
The measuring system meets all the requirements of the following specifications:
• Certified in accordance with the ODVA Conformance Test
• EtherNet/IP Performance Test
• EtherNet/IP PlugFest compliance
Modbus RS485 certification The measuring device meets all the requirements of the MODBUS/TCP conformity test and has the
"MODBUS/TCP Conformance Test Policy, Version 2.0". The measuring device has successfully passed
all the test procedures carried out.
Pressure Equipment The devices can be ordered with or without a PED approval. If a device with a PED approval is
Directive required, this must be explicitly stated in the order. For devices with nominal diameters less than or
equal to DN 25 (1"), this is neither possible nor necessary.
• With the identification PED/G1/x (x = category) on the sensor nameplate, Endress+Hauser
confirms conformity with the "Essential Safety Requirements" specified in Appendix I of the
Pressure Equipment Directive 2014/68/EU.
• Devices bearing this marking (PED) are suitable for the following types of medium:
• Media in Group 1 and 2 with a vapor pressure greater than, or smaller and equal
to0.5 bar (7.3 psi)
• Unstable gases
• Devices not bearing this marking (PED) are designed and manufactured according to good
engineering practice. They meet the requirements of Article 4 paragraph 3 of the Pressure
Equipment Directive 2014/68/EU. The range of application is indicated in tables 6 to 9 in Annex II
of the Pressure Equipment Directive 2014/68/EU.
Other standards and • EN 60529

guidelines Degrees of protection provided by enclosures (IP code)
• IEC/EN 60068-2-6
Environmental influences: Test procedure - Test Fc: vibrate (sinusoidal).
• IEC/EN 60068-2-31
Environmental influences: Test procedure - Test Ec: shocks due to rough handling, primarily for
devices.
• EN 61010-1
Safety requirements for electrical equipment for measurement, control and laboratory use -
general requirements
• IEC/EN 61326
Emission in accordance with Class A requirements. Electromagnetic compatibility (EMC
requirements).
• NAMUR NE 21
Electromagnetic compatibility (EMC) of industrial process and laboratory control equipment
• NAMUR NE 32
Data retention in the event of a power failure in field and control instruments with
microprocessors
• NAMUR NE 43
Standardization of the signal level for the breakdown information of digital transmitters with
analog output signal.
• NAMUR NE 53
Software of field devices and signal-processing devices with digital electronics
• NAMUR NE 80
The application of the pressure equipment directive to process control devices
• NAMUR NE 105
Specifications for integrating fieldbus devices in engineering tools for field devices
• NAMUR NE 107
Self-monitoring and diagnosis of field devices
98 Endress+Hauser
• NAMUR NE 131
Requirements for field devices for standard applications
• NAMUR NE 132
Coriolis mass meter
• NACE MR0103
Materials resistant to sulfide stress cracking in corrosive petroleum refining environments.
• NACE MR0175/ISO 15156-1
Materials for use in H2S-containing Environments in Oil and Gas Production.
Ordering information
Detailed ordering information is available from the following sources:
• In the Product Configurator on the Endress+Hauser website: www.endress.com -> Click "Corporate"
-> Select your country -> Click "Products" -> Select the product using the filters and search field ->
Open product page -> The "Configure" button to the right of the product image opens the Product
Configurator.
• From your Endress+Hauser Sales Center: www.addresses.endress.com
Product Configurator - the tool for individual product configuration
• Up-to-the-minute configuration data
• Depending on the device: Direct input of measuring point-specific information such as
measuring range or operating language
• Automatic verification of exclusion criteria
• Automatic creation of the order code and its breakdown in PDF or Excel output format
• Ability to order directly in the Endress+Hauser Online Shop
Application packages
Many different application packages are available to enhance the functionality of the device. Such
packages might be needed to address safety aspects or specific application requirements.
The application packages can be ordered with the device or subsequently from Endress+Hauser.
Detailed information on the order code in question is available from your local Endress+Hauser sales
center or on the product page of the Endress+Hauser website: www.endress.com.
Detailed information on the application packages:
Special Documentation for the device →  103
Heartbeat Technology Package Description
Heartbeat Verification Heartbeat Verification

+Monitoring Meets the requirement for traceable verification to DIN ISO 9001:2008 Chapter
7.6 a) "Control of monitoring and measuring equipment".
• Functional testing in the installed state without interrupting the process.
• Traceable verification results on request, including a report.
• Simple testing process via local operation or other operating interfaces.
• Clear measuring point assessment (pass/fail) with high test coverage within the
framework of manufacturer specifications.
• Extension of calibration intervals according to operator's risk assessment.
Heartbeat Monitoring
Continuously supplies data, which are characteristic of the measuring principle, to
an external condition monitoring system for the purpose of preventive
maintenance or process analysis. These data enable the operator to:
• Draw conclusions - using these data and other information - about the impact
process influences (such as corrosion, abrasion, buildup etc.) have on the
measuring performance over time.
• Schedule servicing in time.
• Monitor the process or product quality, e.g. gas pockets.
Endress+Hauser 99
Concentration Package Description
Concentration Calculation and outputting of fluid concentrations

The measured density is converted to the concentration of a substance of a binary
mixture using the "Concentration" application package:
• Choice of predefined fluids (e.g. various sugar solutions, acids, alkalis, salts,
ethanol etc.)
• Common or user-defined units (°Brix, °Plato, % mass, % volume, mol/l etc.) for
standard applications.
• Concentration calculation from user-defined tables.
The measured values are output via the digital and analog outputs of the device.
Special density Package Description
Special density Many applications use density as a key measured value for monitoring quality or
controlling processes. The device measures the density of the fluid as standard and
makes this value available to the control system.
The "Special Density" application package offers high-precision density
measurement over a wide density and temperature range particularly for
applications subject to varying process conditions.
Accessories
Various accessories, which can be ordered with the device or subsequently from Endress+Hauser, are
available for the device. Detailed information on the order code in question is available from your
local Endress+Hauser sales center or on the product page of the Endress+Hauser website:
www.endress.com.
Device-specific accessories For the sensor
Accessories Description
Heating jacket Is used to stabilize the temperature of the fluids in the sensor.
Water, water vapor and other non-corrosive liquids are permitted for use as fluids.
If using oil as a heating medium, please consult with Endress+Hauser.
Heating jackets cannot be used with sensors fitted with a rupture disk.
 For details, see Operating Instructions BA00132D

Communication-specific Accessories Description
accessories
Commubox FXA195 For intrinsically safe HART communication with FieldCare via the USB interface.
HART
 For details, see "Technical Information" TI00404F
Commubox FXA291 Connects Endress+Hauser field devices with a CDI interface (= Endress+Hauser
Common Data Interface) and the USB port of a computer or laptop.
 For details, see the "Technical Information" document TI405C/07

HART Loop Converter Is used to evaluate and convert dynamic HART process variables to analog current
HMX50 signals or limit values.
 BA00371F
For details, see "Technical Information" TI00429F and Operating Instructions
Wireless HART adapter Is used for the wireless connection of field devices.
SWA70 The WirelessHART adapter can be easily integrated into field devices and existing
infrastructures, offers data protection and transmission safety and can be operated
in parallel with other wireless networks with minimum cabling complexity.
 For details, see Operating Instructions BA00061S
100 Endress+Hauser
Fieldgate FXA320 Gateway for the remote monitoring of connected 4 to 20 mA measuring devices via
a Web browser.
 BA00053S
For details, see "Technical Information" TI00025S and Operating Instructions
Fieldgate FXA520 Gateway for the remote diagnostics and remote configuration of connected HART
measuring devices via a Web browser.
 For details, see "Technical Information" TI00025S and Operating Instructions

BA00051S
Field Xpert SFX350 Field Xpert SFX350 is a mobile computer for commissioning and maintenance. It
enables efficient device configuration and diagnostics for HART and FOUNDATION
Fieldbus devices and can be used in non-hazardous areas.

Field Xpert SFX370 Field Xpert SFX370 is a mobile computer for commissioning and maintenance. It
enables efficient device configuration and diagnostics for HART and FOUNDATION
Fieldbus devices and can be used in the non-hazardous area and in the hazardous
area.

Service-specific accessories Accessories Description
Applicator Software for selecting and sizing Endress+Hauser measuring devices:

• Choice of measuring devices for industrial requirements
• Calculation of all the necessary data for identifying the optimum flowmeter: e.g.
nominal diameter, pressure loss, flow velocity and accuracy.
• Graphic illustration of the calculation results
• Determination of the partial order code, administration, documentation and
access to all project-related data and parameters over the entire life cycle of a
project.
Applicator is available:
• Via the Internet: https://wapps.endress.com/applicator
• As a downloadable DVD for local PC installation.
W@M W@M Life Cycle Management

Improved productivity with information at your fingertips. Data relevant to a plant
and its components is generated from the first stages of planning and during the
asset’s complete life cycle.
W@M Life Cycle Management is an open and flexible information platform with
online and on-site tools. Instant access for your staff to current, in-depth data
shortens your plant’s engineering time, speeds up procurement processes and
increases plant uptime.
Combined with the right services, W@M Life Cycle Management boosts
productivity in every phase. For more information, visit
www.endress.com/lifecyclemanagement
FieldCare FDT-based plant asset management tool from Endress+Hauser.

It can configure all smart field units in your system and helps you manage them. By
using the status information, it is also a simple but effective way of checking their
status and condition.
 For details, see Operating Instructions BA00027S and BA00059S

DeviceCare Tool for connecting and configuring Endress+Hauser field devices.
 For details, see Innovation brochure IN01047S

Commubox FXA291 Connects Endress+Hauser field devices with a CDI interface (= Endress+Hauser
Common Data Interface) and the USB port of a computer or laptop.
 For details, see "Technical Information" TI00405C
Endress+Hauser 101
System components Accessories Description
Memograph M graphic The Memograph M graphic data manager provides information on all the relevant
data manager measured variables. Measured values are recorded correctly, limit values are
monitored and measuring points analyzed. The data are stored in the 256 MB
internal memory and also on a SD card or USB stick.
 BA00247R
For details, see "Technical Information" TI00133R and Operating Instructions
iTEMP The temperature transmitters can be used in all applications and are suitable for
the measurement of gases, steam and liquids. They can be used to read in the
medium temperature.
 For details, see "Fields of Activity", FA00006T
Supplementary documentation
For an overview of the scope of the associated Technical Documentation, refer to the following:
• The W@M Device Viewer (www.endress.com/deviceviewer): Enter serial number from
nameplate
• The Endress+Hauser Operations App: Enter the serial number from the nameplate or scan the
2-D matrix code (QR code) on the nameplate.
Standard documentation Brief Operating Instructions
Brief Operating Instructions for the sensor

Measuring device Documentation code
Proline Promass F KA01261D
Transmitter Brief Operating Instructions

Proline Promass 100 KA01334D

KA01333D
KA01335D
KA01332D
KA01336D
Technical Information
Proline Promass F 100 TI01034D
Description of Device Parameters
Proline Promass 100 GP01033D
102 Endress+Hauser
Supplementary device- Safety Instructions

dependent documentation
Content Documentation code
ATEX/IECEx Ex i XA00159D
ATEX/IECEx Ex nA XA01029D
cCSAus IS XA00160D
INMETRO Ex i XA01219D
INMETRO Ex nA XA01220D
NEPSI Ex i XA01249D
NEPSI Ex nA XA01262D
Special Documentation
Content Documentation code
Information on the Pressure Equipment Directive SD00142D
Modbus RS485 Register Information SD00154D
Concentration measurement SD01152D
Concentration measurement SD01503D
Heartbeat Technology SD01153D
Heartbeat Technology SD01493D
Web server SD01820D
Web server SD01821D
Web server SD01822D
Web server SD01823D
Installation Instructions
Contents Comment
Installation instructions for spare part sets and accessories Documentation code: specified for each individual accessory .
Registered trademarks
HART®
Registered trademark of the FieldComm Group, Austin, Texas, USA
PROFIBUS®
Registered trademark of the PROFIBUS User Organization, Karlsruhe, Germany
Modbus®
Registered trademark of SCHNEIDER AUTOMATION, INC.
EtherNet/IP™
Trademark of ODVA, Inc.
PROFINET®
Registered trademark of the PROFIBUS User Organization, Karlsruhe, Germany
Microsoft®
Registered trademark of the Microsoft Corporation, Redmond, Washington, USA
TRI-CLAMP®
Registered trademark of Ladish & Co., Inc., Kenosha, USA
Endress+Hauser 103
*71505580*
71505580
www.addresses.endress.com

Promass F

Uploaded by

Copyright:

Available Formats

Promass F

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Promass F

Uploaded by

Copyright:

Available Formats

TI01034D/06/EN/08.

21 Products Solutions Services

The flowmeter with premium accuracy, robustness and an ultra-compact

About this document . . . . . . . . . . . . . . . . . . . . . . . . 4 Shock resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Ordering information . . . . . . . . . . . . . . . . . . . . . . . 99

Supplementary documentation . . . . . . . . . . . . . . 102

Registered trademarks . . . . . . . . . . . . . . . . . . . . . 103

About this document

Direct current and alternating current

Protective Earth (PE)

Symbols for certain types of information

1, 2, 3, ... Item numbers

A-A, B-B, C-C, ... Sections

Function and system design

ν = radial velocity in rotating or oscillating system

Promass 100 Device versions and materials:

PromassF • Excellent performance across a wide range of applications

Safety Barrier Promass 100

• Dual-channel safety barrier for installation in non-hazardous locations

1 Possibilities for integrating measuring devices into a system

Calculated measured variables

Measuring range Measuring ranges for liquids

DN Measuring range full scale values min(F) to max(F)

[mm] [in] [kg/h] [lb/min]

8 ³⁄₈ 0 to 2 000 0 to 73.50

80 3 0 to 180 000 0 to 6 615

100 4 0 to 350 000 0 to 12 860

150 6 0 to 800 000 0 to 29 400

250 10 0 to 2 200 000 0 to 80 850

Measuring ranges for gases

 max(G) Maximum full scale value for gas [kg/h]

 max(F) Maximum full scale value for liquid [kg/h]

 max(G) <  max(F)  max(G) can never be greater than  max(F)

ρG Gas density in [kg/m³] at operating conditions

x Constant dependent on nominal diameter

[mm] [in] [kg/m3]

[mm] [in] [kg/m3]

Calculation example for gas

Recommended measuring range

Operable flow range Over 1000 : 1.

Current output 4-20 mA HART (active)

Maximum output values • DC 24 V (no flow)

Damping Adjustable: 0.07 to 999 s

Assignable measured • Mass flow

Function Can be set to pulse, frequency or switch output

Version Passive, open collector

Maximum input values • DC 30 V

Voltage drop For 25 mA: ≤ DC 2 V

Pulse width Adjustable: 0.05 to 2 000 ms

Maximum pulse rate 10 000 Impulse/s

Pulse value Adjustable

Assignable measured • Mass flow

Output frequency Adjustable: 0 to 10 000 Hz

Damping Adjustable: 0 to 999 s

Pulse/pause ratio 1:1

Assignable measured • Mass flow

Switching behavior Binary, conductive or non-conductive

Switching delay Adjustable: 0 to 100 s

Number of switching Unlimited

Assignable functions • Off