Professional for LCD panel 
 
Complete LCD display kits 
https://www.spectrah.com/product/lcd%20controller%20board%20selection%20guide.pdf
 
See our product category 
https://www.spectrah.com/product/index.php

Datasheet
 

 
 

Product Specification

Color TFT-LCD Module

 
 
 LC420EUD
Product Specification

SPECIFICATION
FOR
APPROVAL

( ) Preliminary Specification
( ● ) Final Specification

Title 42.0” WUXGA TFT LCD

BUYER General SUPPLIER LG Display Co., Ltd.

MODEL *MODEL LC420EUD

SUFFIX SCA1(RoHS Verified)
*When you obtain standard approval,
please use the above model name without suffix

SIGNATURE SIGNATURE
APPROVED BY APPROVED BY
DATE DATE

/ P.Y.Kim / Team Leader

REVIEWED BY

/ Y.S.Kim / Project Leader

PREPARED BY

/ S.H. Lee / Engineer

Please return 1 copy for your confirmation with TV Product Development Dept.
your signature and comments. LG Display Co., Ltd

Ver. 1.0 1 /40

 LC420EUD
Product Specification

CONTENTS
Number ITEM Page
COVER 1

CONTENTS 2
RECORD OF REVISIONS 3

1 GENERAL DESCRIPTION 4

2 ABSOLUTE MAXIMUM RATINGS 5

3 ELECTRICAL SPECIFICATIONS 6

3-1 ELECTRICAL CHARACTERISTICS 6

3-2 INTERFACE CONNECTIONS 8

3-3 SIGNAL TIMING SPECIFICATIONS 11

3-4 LVDS SIGNAL SPECIFICATIONS 12

3-5 COLOR DATA REFERENCE 15

3-6 POWER SEQUENCE 16

4 OPTICAL SPECIFICATIONS 18

5 MECHANICAL CHARACTERISTICS 22

6 RELIABILITY 25

7 INTERNATIONAL STANDARDS 26

7-1 SAFETY 26

7-2 EMC 26

7-3 Environment 26

8 PACKING 27

8-1 INFORMATION OF LCM LABEL 27

8-2 PACKING FORM 27

9 PRECAUTIONS 28
9-1 MOUNTING PRECAUTIONS 28
9-2 OPERATING PRECAUTIONS 28
9-3 ELECTROSTATIC DISCHARGE CONTROL 29
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE 29
9-5 STORAGE 29
9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM 29

Ver. 1.0 2 /40

 LC420EUD
Product Specification

RECORD OF REVISIONS

Revision No. Revision Date Page Description

0.0 Sep, 30, 2009 - Preliminary Specification(First Draft)

1.0 Mar, 10, 2010 - Final Specification

Ver. 1.0 3 /40

 LC420EUD
Product Specification

1. General Description
The LC420EUD is a Color Active Matrix Liquid Crystal Display with an integral Light Emitting Diode (LED)
b a c k l i g h t s ys t e m . T h e m a t r i x e m plo ys a- S i T h in F i lm T r ans is to r as the ac t i ve e lem ent.
It is a transmissive display type which is operating in the normally black mode. It has a 42.02 inch diagonally
measured active display area with WUXGA resolution (1080 vertical by 1920 horizontal pixel array).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arrayed in vertical stripes.
Gray scale or the luminance of the sub-pixel color is determined with a 10-bit gray scale signal for each dot.
Therefore, it can present a palette of more than 1.06Bilion colors.
It has been designed to apply the 10-bit 4-port LVDS interface.
It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut,
high color depth and fast response time are important.

Mini-LVDS(RGB)
CN2 EEPROM
LVDS (41pin) Source Driver Circuit
2Port
LVDS 3,4 SCL SDA S1 S1920

G1
LVDS
LVDS 1,2 Timing Controller
2Port
LVDS Option
LVDS Rx + OPC + DGA + ODC
Integrated Control
TFT - LCD Panel
Select signal Signals (1920 × RGB × 1080 pixels)
CN1 [Gate In Panel]
Bit (51pin)
Select
I2C
+12.0V
Power Circuit Power Signals G1080

Din,DCLK Block
V_sync CN3 V : 6Block
(8 pin)

Local Dimming : 12 Block

+24.0V, GND, On/Off LED Driver
ExtVBR-B H : 2Block

General Features
Active Screen Size 42.02 inches(1067.31mm) diagonal
Outline Dimension 973.2(H) × 566.2(V) X 10.8(B)/23.6 mm(D) (Typ.)
Pixel Pitch 0.4845 mm x 0.4845 mm
Pixel Format 1920 horiz. by 1080 vert. Pixels, RGB stripe arrangement
Color Depth 10bit(D), 1.06Billon colors
Luminance, White 450 cd/m2 (Center 1point ,Typ.)
Viewing Angle (CR>10) Viewing angle free ( R/L 178 (Min.), U/D 178 (Min.))
Power Consumption Total 98W (Typ.) [Logic= 10W, LED Driver= 88W (ExtVbr_B=100% )]
Weight 11.3 Kg (Typ.) ,12.0Kg(Max)
Display Mode Transmissive mode, Normally black
Surface Treatment Hard coating(3H), Anti-glare treatment of the front polarizer (Haze 10%)

Ver. 1.0 4 /40

 LC420EUD
Product Specification

2. Absolute Maximum Ratings

The following items are maximum values which, if exceeded, may cause faulty operation or damage to the
LCD module.

Table 1. ABSOLUTE MAXIMUM RATINGS

Value
Parameter Symbol Unit Note
Min Max
LCD Circuit VLCD -0.3 +14.0 VDC
Power Input Voltage
Driver VBL -0.3 + 27.0 VDC
ON/OFF VOFF / VON -0.3 +5.5 VDC 1
Driver Control Voltage
Brightness EXTVBR-B 0.0 +5.5 VDC
T-Con Option Selection Voltage VLOGIC -0.3 +4.0 VDC
Operating Temperature TOP 0 +50 °C
2,3
Storage Temperature TST -20 +60 °C
Panel Front Temperature TSUR - +68 °C 4
Operating Ambient Humidity HOP 10 90 %RH
2,3
Storage Humidity HST 10 90 %RH

Note1. Ambient temperature condition (Ta = 25 ± 2 °C )

2. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be Max 39°C, and no condensation of water.
3. Gravity mura can be guaranteed below 40°C condition.
4. The maximum operating temperatures is based on the test condition that the surface temperature
of display area is less than or equal to 68°C with LCD module alone in a temperature controlled chamber.
Thermal management should be considered in final product design to prevent the surface temperature of
display area from being over 68℃. The range of operating temperature may degraded in case of
improper thermal management in final product design.
90%

60
60%

50 Storage
Humidity [(%)RH]

Wet Bulb
Temperature [°C]
40
40%
Operation
30
20
10
0
10%

-20 0 10 20 30 40 50 60 70 80

Dry Bulb Temperature [°C]

Ver. 1.0 5 /40

 LC420EUD
Product Specification

3. Electrical Specifications
3-1. Electrical Characteristics

It requires two power inputs. One is employed to power for the LCD circuit. The other Is used for the LED
backlight and LED Driver circuit.

Table 2. ELECTRICAL CHARACTERISTICS

Value
Parameter Symbol Unit Note
Min Typ Max

Circuit :

Power Input Voltage VLCD 10.8 12.0 13.2 VDC

- 815 1060 mA 1
Power Input Current ILCD
- 1140 1482 mA 2

Power Consumption PLCD 9.78 12.72 Watt 1

Rush current IRUSH - - 5 A 3

Note 1. The specified current and power consumption are under the VLCD=12.0V, Ta=25 ± 2°C, fV=120Hz
condition whereas mosaic pattern(8 x 6) is displayed and fV is the frame frequency.
2. The current is specified at the maximum current pattern.
3. The duration of rush current is about 2ms and rising time of power input is 0.5ms (min.).

White : 1023 Gray

Black : 0 Gray

Mosaic Pattern(8 x 6)

Ver. 1.0 6 /40

 LC420EUD
Product Specification
Table 3. ELECTRICAL CHARACTERISTICS (Continue)

Values
Parameter Symbol Unit Notes
Min Typ Max

LED Driver :

Power Supply Input Voltage VBL 22.8 24.0 25.2 Vdc 1

Power Supply Input Current IBL_A - 3.7 4.0 A Ext VBR-B = 100%

VBL = 22.8V
Power Supply Input Current (In-Rush) Irush - - 6.5 A Ext VBR-B = 100%
4

Power Consumption PBL - 88 94.1 W Ext VBR-B = 100%

On V on 2.5 - 5.0 Vdc

On/Off
Off V off -0.3 0.0 0.7 Vdc
Input Voltage for
Control System Brightness Adjust ExtVBR-B 10 - 100 % On Duty
Signals

PWM Frequency for PAL 100 Hz 3

NTSC & PAL NTSC 120 Hz 3

LED :

Life Time 30,000 50,000 Hrs 2

Notes :
1. Electrical characteristics are determined after the unit has been ‘ON’ and stable for approximately 60
minutes at 25±2°C. The specified current and power consumption are under the typical supply Input voltage
24Vand VBR (ExtVBR-B : 100%), it is total power consumption.
2. The life time(MTTF) is determined as the time which luminance of the LED is 50% compared to that of initial
value at the typical LED current (ExtVBR-B :100%) on condition of continuous operating in LCM state at
25±2°C.
3. LGD recommend that the PWM freq. is synchronized with One time harmonic of Vsync signal of system.
Though PWM frequency is over 120Hz (max 252Hz), function of LED Driver is not affected.
4. The duration of rush current is about 10ms.
5. Even though inrush current is over the specified value, there is no problem if I2T spec of fuse is satisfied.

Ver. 1.0 7 /40

 LC420EUD
Product Specification

3-2. Interface Connections

This LCD module employs two kinds of interface connection, 51-pin connector and 41-pin connector are used
for the module electronics and 14-pin connector is used for the integral backlight system.
3-2-1. LCD Module
- LCD Connector : FI-R51S-HF(manufactured by JAE) or KN25-51P-0.5SH(manufactured by Hirose)
(CN1) Refer to below and next Page table
- Mating Connector : FI-R51HL(JAE) or compatible
Table 4-1. MODULE CONNECTOR(CN1) PIN CONFIGURATION
No Symbol Description No Symbol Description
1 NC No Connection 27 Bit Select ‘H’ or NC= 10bit(D) , ‘L’ = 8bit
2 NC No Connection 28 R2AN SECOND LVDS Receiver Signal (A-)
3 NC No Connection 29 R2AP SECOND LVDS Receiver Signal (A+)
4 NC No Connection (Reserved for LGD) 30 R2BN SECOND LVDS Receiver Signal (B-)
5 NC No Connection (Reserved for LGD) 31 R2BP SECOND LVDS Receiver Signal (B+)
6 NC No Connection (Reserved for LGD) 32 R2CN SECOND LVDS Receiver Signal (C-)
7 LVDS Select ‘H’ =JEIDA , ‘L’ or NC = VESA 33 R2CP SECOND LVDS Receiver Signal (C+)
8 NC No Connection 34 GND Ground
9 NC No Connection 35 R2CLKN SECOND LVDS Receiver Clock Signal(-)
10 L-DIM Enable ‘H’ = Enable , ‘L’ or NC = Disable 36 R2CLKP SECOND LVDS Receiver Clock Signal(+)
11 GND Ground 37 GND Ground
12 R1AN FIRST LVDS Receiver Signal (A-) 38 R2DN SECOND LVDS Receiver Signal (D-)
13 R1AP FIRST LVDS Receiver Signal (A+) 39 R2DP SECOND LVDS Receiver Signal (D+)
14 R1BN FIRST LVDS Receiver Signal (B-) 40 R2EN SECOND LVDS Receiver Signal (E-)
15 R1BP FIRST LVDS Receiver Signal (B+) 41 R2EP SECOND LVDS Receiver Signal (E+)
16 R1CN FIRST LVDS Receiver Signal (C-) 42 NC No Connection
17 R1CP FIRST LVDS Receiver Signal (C+) 43 NC No Connection
18 GND Ground 44 GND Ground
19 R1CLKN FIRST LVDS Receiver Clock Signal(-) 45 GND Ground
20 R1CLKP FIRST LVDS Receiver Clock Signal(+) 46 GND Ground
21 GND Ground 47 NC No connection
22 R1DN FIRST LVDS Receiver Signal (D-) 48 VLCD Power Supply +12.0V
23 R1DP FIRST LVDS Receiver Signal (D+) 49 VLCD Power Supply +12.0V
24 R1EN FIRST LVDS Receiver Signal (E-) 50 VLCD Power Supply +12.0V
25 R1EP FIRST LVDS Receiver Signal (E+) 51 VLCD Power Supply +12.0V
26 NC No Connection - - -

Note 1. All GND(ground) pins should be connected together to the LCD module’s metal frame.
2. All VLCD (power input) pins should be connected together.
3. All Input levels of LVDS signals are based on the EIA 644 Standard.
4. Specific pins(pin No. #2~#6) are used for internal data process of the LCD module.
These pins should be no connection.
5. Specific pins(pin No. #10) are used for Local Dimming function of the LCD module.
If not used, these pins are no connection. (Please see the Appendix III-4 for more information.)
6. LVDS pin (pin No. #24,25,40,41) are used for 10Bit(D) of the LCD module.
If used for 8Bit(R), these pins are no connection.
7. Specific pin No. #44 is used for “No signal detection” of system signal interface.
It should be GND for NSB(No Signal Black) during the system interface signal is not.
If this pin is “H”, LCD Module displays AGP(Auto Generation Pattern).
Ver. 1.0 8 /40
 LC420EUD
Product Specification

-LCD Connector : FI-RE41S-HF (manufactured by JAE) or KN25-41P-0.5SH (manufactured by Hirose)

(CN2)
- Mating Connector : FI-RE41HL

Table 4-2. MODULE CONNECTOR(CN2) PIN CONFIGURATION

No Symbol Description No Symbol Description
1 NC No connection(Reserved) 22 RE3N THIRD LVDS Receiver Signal (E-)
2 NC No connection 23 RE3P THIRD LVDS Receiver Signal (E+)
3 NC No connection 24 GND Ground
4 NC No connection 25 GND Ground
5 NC No connection 26 RA4N FORTH LVDS Receiver Signal (A-)
6 NC No connection 27 RA4P FORTH LVDS Receiver Signal (A+)
7 NC No connection 28 RB4N FORTH LVDS Receiver Signal (B-)
8 NC No connection 29 RB4P FORTH LVDS Receiver Signal (B+)
9 GND Ground 30 RC4N FORTH LVDS Receiver Signal (C-)
10 RA3N THIRD LVDS Receiver Signal (A-) 31 RC4P FORTH LVDS Receiver Signal (C+)
11 RA3P THIRD LVDS Receiver Signal (A+) 32 GND Ground
12 RB3N THIRD LVDS Receiver Signal (B-) 33 RCLK4N FORTH LVDS Receiver Clock Signal(-)
13 RB3P THIRD LVDS Receiver Signal (B+) 34 RCLK4P FORTH LVDS Receiver Clock Signal(+)
14 RC3N THIRD LVDS Receiver Signal (C-) 35 GND Ground
15 RC3P THIRD LVDS Receiver Signal (C+) 36 RD4N FORTH LVDS Receiver Signal (D-)
16 GND Ground 37 RD4P FORTH LVDS Receiver Signal (D+)
17 RCLK3N THIRD LVDS Receiver Clock Signal(-) 38 RE4N FORTH LVDS Receiver Signal (E-)
18 RCLK3P THIRD LVDS Receiver Clock Signal(+) 39 RE4P FORTH LVDS Receiver Signal (E+)
19 GND Ground 40 GND Ground
20 RD3N THIRD LVDS Receiver Signal (D-) 41 GND Ground
21 RD3P THIRD LVDS Receiver Signal (D+) -

Note : 1. All GND(ground) pins should be connected together to the LCD module’s metal frame.
2. LVDS pin (pin No. #22,23,38,39) are used for 10Bit(D) of the LCD module.
If used for 8Bit(R), these pins are no connection.
Table 4-3. MODULE CONNECTOR(CN3) PIN CONFIGURATION
No Symbol Description
1 VSYNC Vertical Sync signal
2 GND Backlight Ground
3 GND Backlight Ground
4 SIN Local Dimming Serial Data
5 GND Backlight Ground
6 SCLK Local Dim Serial Clock
7 Reserved No Connection
8 Reverse Local Dimming data Reverse

CN3 #8 #1
CN1 #51 #1
CN2 #41
#1
CN3 #1
CN1 #51 #1
CN2 #41
#1 #8

Rear view of LCM

Ver. 1.0 9 /40

 LC420EUD
Product Specification

3-2-2. Backlight Module

Master
- LED Driver Connector : 20022WR-14B1(Yeonho)
or Equivalent
- Mating Connector : 20022HS-14 or Equivalent
Table 5. LED DRIVER CONNECTOR PIN CONFIGURATION
Pin No Symbol Description Master Note
1 VBL Power Supply +24.0V VBL

2 VBL Power Supply +24.0V VBL

3 VBL Power Supply +24.0V VBL

4 VBL Power Supply +24.0V VBL

5 VBL Power Supply +24.0V VBL

6 GND Backlight Ground GND

7 GND Backlight Ground GND

8 GND Backlight Ground GND 1

9 GND Backlight Ground GND

10 GND Backlight Ground GND

11 NC No connection OPEN or GND

12 VON/OFF Backlight ON/OFF control VON/OFF

13 EXTVBR-B External PWM EXTVBR-B 2

14 NC No connection OPEN or GND TBD

Notes : 1. GND should be connected to the LCD module’s metal frame.

2. High : on duty / Low : off duty, Pin#13 can be opened. ( if Pin #13 is open , EXTVBR-B is 100% )
3. Each impedance of pin #12 and 13 is over 50 [KΩ].

◆ Rear view of LCM

PCB

14
…
…

<Master>
1

Ver. 1.0 10 /40

 LC420EUD
Product Specification

3-3. Signal Timing Specifications

Table 6 shows the signal timing required at the input of the LVDS transmitter. All of the interface signal
timings should be satisfied with the following specification for normal operation.

Table 6-1. TIMING TABLE for NTSC (DE Only Mode)

ITEM Symbol Min Typ Max Unit Note

Display
tHV 480 480 480 tCLK 1920 / 4
Period
Horizontal
Blank tHB 40 70 200 tCLK 1
Total tHP 520 550 680 tCLK
Display
tVV 1080 1080 1080 Lines
Period
Vertical
Blank tVB 16 45 86 Lines 1
Total tVP 1096 1125 1166 Lines

DCLK fCLK 66.97 74.25 78.00 MHz

Frequency Horizontal fH 121.8 135 140 KHz 2

Vertical fV 108 120 122 Hz 2

Table 6-2 TIMING TABLE for DVB/PAL (DE Only Mode)

ITEM Symbol Min Typ Max Unit Note

Display
tHV 480 480 480 tCLK 1920 / 4
Period
Horizontal
Blank tHB 40 70 200 tCLK 1

Total tHP 520 550 680 tCLK

Display
tVV 1080 1080 1080 Lines
Period
Vertical
Blank tVB 228 270 300 Lines 1

Total tVP 1308 1350 1380 Lines

DCLK fCLK 66.97 74.25 78.00 MHz

Frequency Horizontal fH 121.8 135 140 KHz 2

Vertical fV 95 100 104 Hz 2

Note 1. The Input of HSYNC & VSYNC signal does not have an effect on normal operation(DE Only Mode).
If you use spread spectrum for EMI, add some additional clock to minimum value for clock margin.
2. The performance of the electro-optical characteristics may be influenced by variance of the vertical
refresh rate and the horizontal frequency.

Ver. 1.0 11 /40

 LC420EUD
Product Specification

3-4. LVDS Signal Specification

3-4-1. LVDS Input Signal Timing Diagram

0.7VDD
DE, Data
0.3VDD
tCLK
DCLK 0.5 VDD

Valid data

First data Invalid data Pixel 0 Pixel 4 Invalid data

Valid data

Second data Invalid data Pixel 1 Pixel 5 Invalid data

Valid data

Third data Invalid data Pixel 2 Pixel 6 Invalid data

Valid data

Forth data Invalid data Pixel 3 Pixel 7 Invalid data

DE(Data Enable)

* tHB = tHFP + tWH +tHBP

* tVB = tVFP + tWV +tVBP

1 1080

DE(Data Enable)

tVV

tVP

Ver. 1.0 12 /40

 LC420EUD
Product Specification

3-4-2. LVDS Input Signal Characteristics

1) DC Specification
LVDS -

LVDS +

V CM V IN _ MAX V IN _ MIN

# V CM = {( LVDS +) + ( LVDS - )} /2
0V

Description Symbol Min Max Unit Note

LVDS Common mode Voltage VCM 1.0 1.5 V -
LVDS Input Voltage Range VIN 0.7 1.8 V -
Change in common mode Voltage ΔVCM 250 mV -
2) AC Specification
Tclk

LVDS Clock

LVDS Data

( F clk = 1/T clk )

tSKEW tSKEW
A
Tclk
LVDS 1’st Clock 80%

LVDS 2nd / 3rd / 4th Clock

20%
tRF
tSKEW_min tSKEW_max

Description Symbol Min Max Unit Note

High Threshold VTH 100 300 mV
LVDS Differential Voltage 3
Low Threshold VTL -300 -100 mV
LVDS Clock to Data Skew Margin tSKEW |(0.25*Tclk)/7| ps -
LVDS Clock/DATA Rising/Falling time tRF 260 (0.3*Tclk)/7 ps 2
Effective time of LVDS teff ±360 ps -
LVDS Clock to Clock Skew Margin (Even to Odd) tSKEW_EO 1/7* Tclk Tclk -
Note 1. All Input levels of LVDS signals are based on the EIA 644 Standard.
2. If tRF isn’t enough, teff should be meet the range.
3. LVDS Differential Voltage is defined within teff

Ver. 1.0 13 /40

 LC420EUD
Product Specification

360ps

0.5tui tui
V+
data

VTH
Vcm
VTL

V-
360ps
data
teff
V+ tui : Unit Interval
clk

Vcm

V-
clk

Ver. 1.0 14 /40

 LC420EUD
Product Specification

3-5. Color Data Reference

The brightness of each primary color(red,green,blue) is based on the 10-bit gray scale data input for the color.
The higher binary input, the brighter the color. Table 7 provides a reference for color versus data input.

Table 7. COLOR DATA REFERENCE

Input Color Data

RED GREEN BLUE

Color
MSB LSB MSB LSB MSB LSB

R9 R8 R7 R6 R5 R4 R3 R2 R1 R0 G9 G8 G7 G6 G5 G4 G3 G2 G1 G0 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Red (1023) 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green
0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0
(1023)
Basic Blue (1023) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1

Color Cyan 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Magenta 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1

Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0

White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

RED (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED (001) 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED ... ... ... ...

RED (1022) 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED (1023) 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0

GREEN ... ... ... ...

GREEN
0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0
(1022)
GREEN
0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0
(1023)
BLUE (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

BLUE (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1

BLUE ... ... ... ...

BLUE (1022) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0

BLUE (1023) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1

Ver. 1.0 15 /40

 LC420EUD
Product Specification

3-6. Power Sequence

3-6-1. LCD Driving circuit

90% 90%
Power Supply For LCD
VLCD 10% 10% 10%
0V
T8
T1
T5
T2
Valid Data Vcm : LVDS Common mode Voltage
30%
Interface Signal (Tx_clock) 0V

100% T3 T4
T6
User Control Signal
(LVDS_select, BIT _select, L-DIM Enable)

Power for LED T7 LED ON

Table 8. POWER SEQUENCE

Value
Parameter Unit Notes
Min Typ Max
T1 0.5 - 20 ms
T2 0 - - ms 4
T3 200 - - ms 3
T4 200 - - ms 3
T5 1.0 - - s 5
T6 - - T2 ms 4
T7 0.5 - s
T8 100 - ms 6

Note :1. Please avoid floating state of interface signal at invalid period.
2. When the power supply for LCD (VLCD) is off, be sure to pull down the valid and invalid data to 0V.
3. The T3 / T4 is recommended value, the case when failed to meet a minimum specification,
abnormal display would be shown. There is no reliability problem.
4. If the on time of signals(Interface signal and user control signals) precedes the on time of Power(VLCD),
it will be happened abnormal display. When T6 is NC status, T6 doesn’t need to be measured.
5. T5 should be measured after the Module has been fully discharged between power off and on
period.
6. It is recommendation specification that T8 has to be 100ms as a minimum value.

Ver. 1.0 16 /40

 LC420EUD
Product Specification

3-6-2. Sequence for LED Driver

Power Supply For LED Driver
24V (typ.)
90% 90%
VBL
10%
0V

T1 T2 T3

VON/OFF
LED ON

Ext-VBR-B

T4 T5

3-6-3. Dip condition for LED Driver

T6
VBL : 24V

VBL(Typ.) x 0.8

0V

Table 9. Power Sequence for LED Driver

Values
Parameter Units Remarks
Min Typ Max
T1 20 - - ms 1
T2 500 - - ms
T3 10 - ms
T4 0 - - ms
T5 0 - - ms
T6 - - 10 ms VBL(Typ) x 0.8

Notes : 1. T1 describes rising time of 0V to 24V and this parameter does not applied at restarting time.
Even though T1 is over the specified value, there is no problem if I2T spec of fuse is satisfied.

Ver. 1.0 17 /40

 LC420EUD
Product Specification

4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable in a dark environment at
25±2°C. The values are specified at an approximate distance 50cm from the LCD surface at a viewing angle
of Φ and θ equal to 0 °.
It is presented additional information concerning the measurement equipment and method in FIG. 1.
LCD Module Pritchard 880 or
Optical Stage(x,y)
equivalent

50cm
FIG. 1 Optical Characteristic Measurement Equipment and Method

Ta= 25±2°C, VLCD=12.0V, fV=120Hz, Dclk=74.25MHz,

Table 10. OPTICAL CHARACTERISTICS EXTVBR-B =100%
Value
Parameter Symbol Unit Note
Min Typ Max
Contrast Ratio CR 1000 1400 - 1
Surface Luminance, white LWH 360 450 - cd/m2 2
Luminance Variation δ WHITE 5P - - 1.3 3
Gray-to-Gray G to G - 5 8 ms 4,5
MPRT MPRT - 8 12 ms
Response Time
Uniformity δ MPRT - - 1
Uniformity δ G TO G - - 1
Rx 0.647
RED
Ry 0.332
Gx 0.309
GREEN
Color Coordinates Gy Typ 0.601 Typ
[CIE1931] Bx -0.03 0.149 +0.03
BLUE
By 0.059
Wx 0.279
WHITE
Wy 0.292
Color Temperature 10,000 K
Color Gamut(CIE1931 NTSC) 72 %
Viewing Angle (CR>10)
x axis, right(φ=0°) θr 89 - -
x axis, left (φ=180°) θl 89 - -
degree 6
y axis, up (φ=90°) θu 89 - -
y axis, down (φ=270°) θd 89 - -
Gray Scale - - - 7

Ver. 1.0 18 /40

 LC420EUD
Product Specification
Note : 1. Contrast Ratio(CR) is defined mathematically as :

Surface Luminance with all white pixels

Contrast Ratio =
Surface Luminance with all black pixels
It is measured at center 1-point.
2. Surface luminance are determined after the unit has been ‘ON’ and 1 Hour after lighting the
backlight in a dark environment at 25±2°C. Surface luminance is the luminance value at center
1-point across the LCD surface 50cm from the surface with all pixels displaying white.
For more information see the FIG. 2.
3. The variation in surface luminance , δ WHITE is defined as :

δ WHITE(5P) = Maximum(Lon1,Lon2, Lon3, Lon4, Lon5) / Minimum(Lon1,Lon2, Lon3, Lon4, Lon5)

Where Lon1 to Lon5 are the luminance with all pixels displaying white at 5 locations .
For more information, see the FIG. 2.
4. Response time is the time required for the display to transit from G(N) to G(M) (Rise Time, TrR)
and from G(M) to G(N) (Decay Time, TrD). For additional information see the FIG. 3. (N<M)
※ G to G Spec stands for average value of all measured points.
Photo Detector : RD-80S / Field : 2˚
5. MPRT is defined as the 10% to 90% blur-edge width Bij(pixels) and scroll speed U(pixels/frame)at
the moving picture. For more information, see FIG 4
6. Gray to Gray / MPRT Response time uniformity is Reference data. Appendix IV-1 / IV-2.
7. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the LCD module surface. For more information, see the FIG. 5.
8. Gray scale specification
Gamma Value is approximately 2.2. For more information, see the Table 11.
Table 11. GRAY SCALE SPECIFICATION
Gray Level Luminance [%] (Typ)
L0 0.07
L15 0.27
L31 1.04
L47 2.49
L63 4.68
L79 7.66
L95 11.5
L111 16.1
L127 21.6
L143 28.1
L159 35.4
L175 43.7
L191 53.0
L207 63.2
L223 74.5
L239 86.7
L255 100

Ver. 1.0 19 /40

 LC420EUD
Product Specification

Measuring point for surface luminance & measuring point for luminance variation.

H
A

② ③

①
V
B

A : H / 4 mm
④ ⑤ B : V / 4 mm
@ H,V : Active Area

FIG. 2 5 Points for Luminance Measure

Response time is defined as the following figure and shall be measured by switching the input signal for
“Gray(N)” and “Gray(M)”.

TrR TrD
100
90

Optical
Response

10
Gray(N) Gray(M) Gray(N)
0
N,M = Black~White, N<M

FIG. 3 Response Time

Ver. 1.0 20 /40

 LC420EUD
Product Specification

MPRT is defined as the 10% to 90% blur-edge with Bij(pixels) and scroll speed U(pixels/frame)at the moving
picture.

Lj
1 90%
M= Bij (i=j)
U
Example) Bij = 12pixels, U = 10pixels / 120Hz
M = 12pixels / (10pixels / 120Hz) 10%
= 12pixels / {10pixels / (1/120)s}
= 12 / 1,200 s
L i
Bij
= 10 ms
FIG. 4 MPRT

Dimension of viewing angle range

Normal
E Y
φ = 90 ° , Up

φ = 180 ° , Left
θ

φ = 0 ° , Right

φ = 270 ° , Down

FIG. 5 Viewing Angle

Ver. 1.0 21 /40

 LC420EUD
Product Specification

5. Mechanical Characteristics

Table 10 provides general mechanical characteristics.

Table 10. MECHANICAL CHARACTERISTICS

Item Value

Horizontal 973.2 mm

Outline Dimension Vertical 566.2 mm

Depth 10.8 mm

Horizontal 937.2 mm
Bezel Area
Vertical 530.2 mm

Horizontal 930.24 mm
Active Display Area
Vertical 523.26 mm

Weight 11.3 Kg(Typ), 12.0Kg(Max)

Note : Please refer to a mechanical drawing in terms of tolerance at the next page.

Ver. 1.0 22 /40

<Front View> LC420EUD
Product Specification

Ver. 1.0 23 /40

<Rear View> LC420EUD
Product Specification

Ver. 1.0 24 /40

 LC420EUD
Product Specification

6. Reliability
Table 13. ENVIRONMENT TEST CONDITION

No. Test Item Condition

1 High temperature storage test Ta= 60°C 240h

2 Low temperature storage test Ta= -20°C 240h

3 High temperature operation test Ta= 50°C 50%RH 240h

4 Low temperature operation test Ta= 0°C 240h

Wave form : random

Vibration level : 1.0Grms
Vibration test
5 Bandwidth : 10-300Hz
(non-operating)
Duration : X,Y,Z, 30 min
Each direction per 10 min

Shock level : 50Grms,35G(Z axis)

Shock test Waveform : half sine wave, 11ms
6
(non-operating) Direction : ±X, ±Y, ±Z
One time each direction

7 Humidity condition Operation Ta= 40 °C ,90%RH

Altitude operating 0 - 15,000 ft

8
storage / shipment 0 - 40,000 ft

Note : Before and after Reliability test, LCM should be operated with normal function.

Ver. 1.0 25 /40

 LC420EUD
Product Specification

7. International Standards

7-1. Safety
a) UL 60065, Seventh Edition, Underwriters Laboratories Inc.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
b) CAN/CSA C22.2 No.60065:03, Canadian Standards Association.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
c) EN 60065:2002 + A11:2008, European Committee for Electrotechnical Standardization (CENELEC).
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
d) IEC 60065:2005 + A1:2005, The International Electrotechnical Commission (IEC).
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
(Including report of IEC60825-1:2001 clause 8 and clause 9)
Notes
1. Laser (LED Backlight) Information

Class 1 LED Product

IEC60825-1 : 2001
Embedded LED Power (Class 1)

7-2. EMC
a) ANSI C63.4 “American National Standard for Methods of Measurement of Radio-Noise
Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz.”
American National Standards Institute (ANSI), 2003.
b) CISPR 22 “Information technology equipment – Radio disturbance characteristics – Limit and
methods of measurement." International Special Committee on Radio Interference
(CISPR), 2005.
c) CISPR 13 “Sound and television broadcast receivers and associated equipment – Radio disturbance
characteristics – Limits and method of measurement." International Special Committee on Radio
Interference (CISPR), 2006.

7-3. Environment
a) RoHS, Directive 2002/95/EC of the European Parliament and of the council of 27 January 2003

Ver. 1.0 26 /40

 LC420EUD
Product Specification

8. Packing
8-1. Information of LCM Label
a) Lot Mark

A B C D E F G H I J K L M

A,B,C : SIZE(INCH) D : YEAR

E : MONTH F ~ M : SERIAL NO.

Note
1. YEAR
Year 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010

Mark 1 2 3 4 5 6 7 8 9 0

2. MONTH

Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec

Mark 1 2 4 4 5 6 7 8 9 A B C

b) Location of Lot Mark

Serial NO. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.

8-2. Packing Form

a) Package quantity in one pallet : 15 ea

b) Pallet Size : 1140 mm X 990 mm X 798mm

Ver. 1.0 27 /40

 LC420EUD
Product Specification

9. Precautions
Please pay attention to the followings when you use this TFT LCD module.
9-1. Mounting Precautions
(1) You must mount a module using specified mounting holes (Details refer to the drawings).
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the
module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzine. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.

9-2. Operating Precautions

(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V=±200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on)
becomes longer
(4) Be careful for condensation at sudden temperature change.Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.
(7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can’t be operated
its full characteristics perfectly.
(8) A screw which is fastened up the steels should be a machine screw.
(if not, it can causes conductive particles and deal LCM a fatal blow)
(9) Please do not set LCD on its edge.
(10) The conductive material and signal cables are kept away from LED driver inductor to prevent abnormal
display, sound noise and temperature rising.

Ver. 1.0 28 /40

 LC420EUD
Product Specification

9-3. Electrostatic Discharge Control

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

9-4. Precautions for Strong Light Exposure

Strong light exposure causes degradation of polarizer and color filter.

9-5. Storage
When storing modules as spares for a long time, the following precautions are necessary.

(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.

9-6. Handling Precautions for Protection Film

(1) The protection film is attached to the bezel with a small masking tape.
When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-
blown equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a very
small amount of glue still on the bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized,
please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-
hexane.

Ver. 1.0 29 /40

 LC420EUD
Product Specification

# APPENDIX-I
■ LC420EUD-SCA1 – Pallet Ass’y

NO. DESCRIPTION MATERIAL

1 LCD Module
2 BAG 42INCH
3 TAPE MASKING 20MMX50M
4 PALLET Plywood 1140X990X125.5mm
5 PACKING,BOTTOM EPS
6 PACKING,TOP EPS
7 ANGLE,POST PAPER
8 ANGLE,PACKING PAPER
9 ANGLE.COVER PAPER
10 BAND,CLIP STEEL or PP
11 BAND PP
12 LABEL YUPO 80G 100X70

Ver. 1.0 30 /40

 LC420EUD
Product Specification

# APPENDIX- II-1
■ LC420EUD-SCA1-LCM Label

Model LC420EUD
(SC)(A1)

Serial No.
UL, TUV Mark
LGD Logo
US PATENT No. Origin

Ver. 1.0 31 /40

 LC420EUD
Product Specification

# APPENDIX- II-2
■ LC420EUD-SCA1-Pallet Label

LC420EUD
SCA1
15 PCS 001/01-01
MADE IN KOREA RoHS Verified

XXXXXXXXXXXXX XXX

Ver. 1.0 32 /40

 LC420EUD
Product Specification

# APPENDIX- III-1
■ Required signal assignment for Flat Link (Thine : THC63LVD103) Transmitter(Pin7=“L”)

Host System THC63LVD103

30 Bit or Compatible Timing
RED0 33 Controller
RED1 34 FI-RE51S-HF
RED2 35
RED3 36
31
RED4 37 TA- 12 RO0N
30 100Ω
RED5 38 TA+ 13 RO0P
RED6 59
RED7 61 29
TB- 14 RO1N
RED8 4 28 100Ω
TB+ 15 RO1P
RED9 5
GREEN0 40
25
GREEN1 41 TC- 16 RO2N
GREEN2 42 24 100Ω
TC+ 17 RO2P
GREEN3 44
GREEN4 45 23
TCLK- 19 ROCLKN
GREEN5 46 22 100Ω
GREEN6 62 TCLK+ 20 ROCLKP
GREEN7 63
21
GREEN8 6 TD- 22 RO3N
GREEN9 8 20 100Ω
TD+ 23 RO3P
BLUE0 48
BLUE1 49 19
TE- 24 RO4N
BLUE2 50 18 100Ω
BLUE3 52 TE+ 25 RO4P
BLUE4 53
BLUE5 54 7 VESA/ JEIDA
BLUE6 64
BLUE7 1
BLUE8 9
BLUE9 11
Hsync 55 LCM Module
GND

Vsync 57
Data Enable 58
CLOCK 12

Note: 1. The LCD module uses a 100 Ohm[Ω] resistor between positive and negative lines of each receiver
input.
2. Refer to LVDS Transmitter Data Sheet for detail descriptions. (THC63LVD103 or Compatible)
3. ‘9’ means MSB and ‘0’ means LSB at R,G,B pixel data.
Ver. 1.0 33 /40
 LC420EUD
Product Specification

# APPENDIX- III-1
■ Required signal assignment for Flat Link (Thine : THC63LVD103) Transmitter(Pin7=“H”)

Host System THC63LVD103

30 Bit or Compatible Timing
RED0 4 Controller
RED1 5 FI-RE51S-HF
RED2 59
RED3 61
31
RED4 33 TA- 12 RO0N
30 100Ω
RED5 34 TA+ 13 RO0P
RED6 35
RED7 36 29
TB- 14 RO1N
RED8 37 28 100Ω
TB+ 15 RO1P
RED9 38
GREEN0 6
25
GREEN1 8 TC- 16 RO2N
GREEN2 62 24 100Ω
TC+ 17 RO2P
GREEN3 63
GREEN4 40 23
TCLK- 19 ROCLKN
GREEN5 41 22 100Ω
GREEN6 42 TCLK+ 20 ROCLKP
GREEN7 44
21
GREEN8 45 TD- 22 RO3N
GREEN9 46 20 100Ω
TD+ 23 RO3P
BLUE0 9
BLUE1 11 19
TE- 24 RO4N
BLUE2 64 18 100Ω
BLUE3 1 TE+ 25 RO4P
BLUE4 48
BLUE5 49 7 VESA /JEIDA
BLUE6 50
BLUE7 52
BLUE8 53
BLUE9 54
Hsync 55 LCM Module
VCC

Vsync 57
Data Enable 58
CLOCK 12

Note :1. The LCD module uses a 100 Ohm[Ω] resistor between positive and negative lines of each receiver
input.
2. Refer to LVDS Transmitter Data Sheet for detail descriptions. (THC63LVD103 or Compatible)
3. ‘9’ means MSB and ‘0’ means LSB at R,G,B pixel data.
Ver. 1.0 34 /40
 LC420EUD
Product Specification

# APPENDIX- III-2
■ LVDS Data-Mapping Information (10 Bit )

1) LVDS Select : “H” Data-Mapping (JEIDA format)

RCLKP

RCLKM

RAP R15’ R14’ G14 R19 R18 R17 R16 R15 R14 G14”

RBP G16’ G15’ B15 B14 G19 G18 G17 G16 G15 B15”

RCP B17’ B16’ DE VSYNC HSYNC B19 B18 B17 B16 DE”

RDP R13’ R12’ X B13 B12 G13 G12 R13 R12 X”

REP R11’ R10’ X B11 B10 G11 G10 R11 R10 X”

2) LVDS Select : “L” Data-Mapping (VESA format)

RCLKP

RCLKM

RAP R11’ R10’ G10 R15 R14 R13 R12 R11 R10 G10”

RBP G12’ G11’ B11 B10 G15 G14 G13 G12 G11 B15”

RCP B13’ B12’ DE VSYNC HSYNC B15 B14 B13 B12 DE”

RDP R17’ R16’ X B17 B16 G17 G16 R17 R16 X”

REP R19’ R18’ X B19 B18 G19 G18 R19 R18 X”

Ver. 1.0 35 /40

 LC420EUD
Product Specification

# APPENDIX- III-2
■ LVDS Data-Mapping Information (8 Bit )

1) LVDS Select : “H” Data-Mapping (JEIDA format)

RCLKP

RCLKM

RAP R13’ R12’ G12 R17 R16 R15 R14 R13 R12 G12”

RBP G14’ G13’ B13 B12 G17 G16 G15 G14 G13 B13”

RCP B15’ B14’ DE VSYNC HSYNC B17 B16 B15 B14 DE”

RDP R11’ R10’ X B11 B10 G11 G10 R11 R10 X”

2) LVDS Select : “L” Data-Mapping (VESA format)

RCLKP

RCLKM

RAP R11’ R10’ G10 R15 R14 R13 R12 R11 R10 G10”

RBP G12’ G11’ B11 B10 G15 G14 G13 G12 G11 B15”

RCP B13’ B12’ DE VSYNC HSYNC B15 B14 B13 B12 DE”

RDP R17’ R16’ X B17 B16 G17 G16 R17 R16 X”

Ver. 1.0 36 /40

 LC420EUD
Product Specification

# APPENDIX- III-3
■ Option Pin Circuit Block Diagram

1) Circuit Block Diagram of LVDS Format Selection pin

LVDS Select Pin : Pin 9

Ω
1KΩ
LVDS Select
LVDS Select
(Pin 9)

Ω
50KΩ

ASIC
(TCON)

System Side LCM Side

2) Circuit Block Diagram of L-Dim Enable Selection pin

L-Dim Enable Pin : Pin 10

VCC VCC

OPEN Ω
50KΩ
R1 Ω
1KΩ
L-Dim _Enable
L-Dim _Enable
(Pin 10)

ASIC
(TCON)

System Side
R1 ≤ 1KΩ
Ω LCM Side

Ver. 1.0 37 /40

 LC420EUD
Product Specification

# APPENDIX- III-4
■ EXTVBR-B & Local Dimming Design Guide
1) When L-Dim Enable is “L", Vertical Sync Signal = System Dimming with 100Hz or 120Hz frequency.
2) Local Dimming signals are synchronized with V-Sync Freq. of System in T-Con Board.

3) EXTVBR-B Specification ( VCC = 3.3V ) @ Local Dimming

a) High Voltage Range : 2.5 V ~ 3.6 V
b) Low Voltage Range : 0.0 V ~ 0.8 V

(8pin)
#1 : Vertical Sync signal
#2 : Reserved
#3 : Reserved
#4 : Local Dimming Serial Data LCM T-con Board
#5 : GND #1
#6 : Local Dim Serial Clock
#7 : Reserved
#8 : Reverse

#8
T-Con
(51pin)
#8 : EXTVBR-B
#9 : NC
#10 : L-DIM Enable
#1 51 #1 41
#11 : NC CNT1 51pin CNT2 41pin

CNT4 CNT4
#8 #1
B/L Signal
Generation Local Dimming On
Block 3.3V
#13 : EXTVBR-B

System
Local Dimming Off
Main IC
(PWM Generator)

LED 14pin
Driver Chassis

<With Driver Model>

VCC
MAX 1Khz
EXTVBR-B VCC*0.9
Recommendation: 100 Hz for PAL
Frequency
120 Hz for NTSC Rising Time

Rising Time MAX 10.0 μs Falling Time

VCC*0.1
Falling Time MAX 10.0 μs
0

Ver. 1.0 38 /40

 LC420EUD
Product Specification

# APPENDIX- IV-1
Gray to Gray Response Time Uniformity
This is only the reference data of G to G and uniformity for LC420EUD-SCA1 model.
1. G to G Response Time :
Response time is defined as Figure3 and shall be measured by switching the input signal for
“Gray (N) ” and “Gray(M)”.(32Gray Step at 8bit)

2. G to G Uniformity
The variation of G to G Uniformity , δ G to G is defined as :
Maximum(GtoG ) − Typical (GtoG )
G to G Uniformity = ≤1
Typical (GtoG )

*Maximum (GtoG) means maximum value of measured time (N, M = 0 (Black) ~ 1023(White), 128 gray step).

0Gray 127ray 255Gray … 895Gray 1023Gray

0Gray TrR:0G
127G TrR:0G
255G … TrR:0G
895G TrR:0G
1023G
127Gray TrD:127G
0G TrR:127G
255G … TrR:127G
895G TrR:127G
1023G
255Gray TrD:255G
0G TrD:255G
127G … TrR:255G
895G TrR:255G
1023G
… … … … … …
895Gray TrD:895G
0G TrD:895G
127G TrD:895G
255G … TrR:895G
1023G
1023Gray TrD:1023G
0G TrD:1023G
127G TrD:1023G
255G … TrD:1023G
895G

3. Sampling Size : 2 pcs

4. Measurement Method : Follow the same rule as optical characteristics measurement.

5. Current Status
Below table is actual data of production on Mar. 09. 2010

G to G Response Time [ms]

Uniformity
Min. Max.
#1 4.24 7.42 0.57
#2 3.82 7.65 0.69

G255 G223 G191

G255 G223 G191

G159 G127 G95

G159 G127 G95

G63 G31 G0 G63 G31 G0

<#1> <#2>
Ver. 1.0 39 /40
 LC420EUD
Product Specification

# APPENDIX- IV-2
■ MPRT Response Time Uniformity (δ
δ MPRT )
This is only the reference data of MPRT and uniformity for LC420EUD-SCA1 model.
1. MPRT Response Time :
Response time is defined as Figure3

2. MPRT Uniformity
The variation of MPRT Uniformity , δ MPRT is defined as :

Maximum (MPRT) - Typical (MPRT)

MPRT Uniformity = ≤1
Typical (MPRT)

3. Sampling Size : 2 pcs

4. Measurement Method : Follow the same rule as optical characteristics measurement.

5. Current Status
Below table is actual data of production on XXX Mar. 09. 2010

MPRT Response Time [ms]

Sample Uniformity
Min. Max.
#1 7.05 10.2 0.39

#2 7.53 10.3 0.34

Ver. 1.0 40 /40