Procedures for Drawing a Block Diagram.

To draw a block diagram for a sys-

tem, first write the equations that describe the dynamic behavior of each component.

Then take the Laplace transforms of these equations, assuming zero initial conditions,

and represent each Laplace-transformed equation individually in block form. Finally, as-

semble the elements into a complete block diagram.

As an example, consider the RC circuit shown in Figure 2–12(a). The equations for

this circuit are

(2–4)

(2–5)

The Laplace transforms of Equations (2–4) and (2–5), with zero initial condition, become

(2–6)

(2–7)

Equation (2–6) represents a summing operation, and the corresponding diagram is

shown in Figure 2–12(b). Equation (2–7) represents the block as shown in Figure 2–12(c).

Assembling these two elements, we obtain the overall block diagram for the system as

shown in Figure 2–12(d).

Block Diagram Reduction. It is important to note that blocks can be connected

in series only if the output of one block is not affected by the next following block. If

there are any loading effects between the components, it is necessary to combine these

components into a single block.

Any number of cascaded blocks representing nonloading components can be

replaced by a single block, the transfer function of which is simply the product of the

individual transfer functions.

Eo(s) = I(s)

Cs

I(s) = Ei
(s) - Eo(s)

eo = 1i dt

i = ei - eo

(d)

Ei(s) I(s) Eo(s) 1

Cs

Eo(s)

(b)

Ei(s) I(s) 1

(c)

I(s) Eo(s) 1

Cs

(a)

ei C eo

+–

+–
Figure 2–12

(a) RC circuit;

(b) block diagram

representing

Equation (2–6);

(c) block diagram

representing

Equation (2–7);

(d) block diagram of

the RC circuit.

28 Chapter 2 / Mathematical Modeling of Control Systems

G1

H1

H2

G2 G3

G1

H1

G2 G3

C
R

G3

RC

RC

(a)

(b)

(c)

(d)

(e)

H2

G1

H2

G1

G1G2

1 – G1G2H1

G1G2G3

1 – G1G2H1 + G2G3H2
G1G2G3

1 – G1G2H1 + G2G3H2 + G1G2G3

+–+

– ++

+–+

–+

+–+–

+ – Figure 2–13

(a) Multiple-loop

system;

(b)–(e) successive

reductions of the

block diagram shown

in (a).

A complicated block diagram involving many feedback loops can be simplified by

a step-by-step rearrangement. Simplification of the block diagram by rearrangements

considerably reduces the labor needed for subsequent mathematical analysis. It should

be noted, however, that as the block diagram is simplified, the transfer functions in new

blocks become more complex because new poles and new zeros are generated.

EXAMPLE 2–1 Consider the system shown in Figure 2–13(a). Simplify this diagram.

By moving the summing point of the negative feedback loop containing H2 outside the posi-

tive feedback loop containing H1, we obtain Figure 2–13(b). Eliminating the positive feedback loop,
we have Figure 2–13(c).The elimination of the loop containing H2/G1 gives Figure 2–13(d). Finally,

eliminating the feedback loop results in Figure 2–13(e).

Openmirrors.com

Section 2–4 / Modeling in State Space 29

Notice that the numerator of the closed-loop transfer function C(s)/R(s) is the product of the

transfer functions of the feedforward path. The denominator of C(s)/R(s) is equal to

(The positive feedback loop yields a negative term in the denominator.)

2–4 MODELING IN STATE SPACE

In this section we shall present introductory material on state-space analysis of control

systems.

Modern Control Theory. The modern trend in engineering systems is toward

greater complexity, due mainly to the requirements of complex tasks and good accu-

racy. Complex systems may have multiple inputs and multiple outputs and may be time

varying. Because of the necessity of meeting increasingly stringent requirements on

the performance of control systems, the increase in system complexity, and easy access

to large scale computers, modern control theory, which is a new approach to the analy-

sis and design of complex control systems, has been developed since around 1960.This

new approach is based on the concept of state. The concept of state by itself is not

new, since it has been in existence for a long time in the field of classical dynamics and

other fields.

Modern Control Theory Versus Conventional Control Theory. Modern con-

cable to multiple-input, multiple-output systems, which may be linear or nonlinear,

time invariant or time varying, while the latter is applicable only to linear time-

invariant single-input, single-output systems. Also, modern control theory is essen-

tially time-domain approach and frequency domain approach (in certain cases such as

H-infinity control), while conventional control theory is a complex frequency-domain

approach. Before we proceed further, we must define state, state variables, state vector,

and state space.

State. The state of a dynamic system is the smallest set of variables (called state

variables) such that knowledge of these variables at t=t0 , together with knowledge of

the input for t t0 , completely determines the behavior of the system for any time

t t0 .

Note that the concept of state is by no means limited to physical systems. It is appli-

cable to biological systems, economic systems, social systems, and others.

State Variables. The state variables of a dynamic system are the variables mak-

ing up the smallest set of variables that determine the state of the dynamic system. If at

= 1 - G1G2H1 + G2G3H2 + G1G2G3

= 1 + A-G1G2H1 + G2G3H2 + G1G2G3B

1 + a (product of the transfer functions around each loop)

30 Chapter 2 / Mathematical Modeling of Control Systems

least n variables x1 , x2 , p , xn are needed to completely describe the behavior of a dy-

namic system (so that once the input is given for t t0 and the initial state at t=t0 is

specified, the future state of the system is completely determined), then such n variables
are a set of state variables.

Note that state variables need not be physically measurable or observable quantities.

Variables that do not represent physical quantities and those that are neither measura-

ble nor observable can be chosen as state variables. Such freedom in choosing state vari-

ables is an advantage of the state-space methods. Practically, however, it is convenient

to choose easily measurable quantities for the state variables, if this is possible at all, be-

cause optimal control laws will require the feedback of all state variables with suitable

weighting.

State Vector. If n state variables are needed to completely describe the behavior

of a given system, then these n state variables can be considered the n components of a

vector x. Such a vector is called a state vector. A state vector is thus a vector that deter-

mines uniquely the system state x(t) for any time t t0 , once the state at t=t0 is given

and the input u(t) for t t0 is specified.

State Space. The n-dimensional space whose coordinate axes consist of the x1

axis, x2 axis, p , xn axis, where x1, x2, p , xn are state variables, is called a state space.Any

state can be represented by a point in the state space.

State-Space Equations. In state-space analysis we are concerned with three types

of variables that are involved in the modeling of dynamic systems: input variables, out-

put variables, and state variables. As we shall see in Section 2–5, the state-space repre-

sentation for a given system is not unique, except that the number of state variables is

the same for any of the different state-space representations of the same system.

The dynamic system must involve elements that memorize the values of the input for

t t1 . Since integrators in a continuous-time control system serve as memory devices,

nal state of the dynamic system.Thus the outputs of integrators serve as state variables.

The number of state variables to completely define the dynamics of the system is equal

to the number of integrators involved in the system.

Assume that a multiple-input, multiple-output system involves n integrators.Assume

also that there are r inputs u1(t), u2(t), p , ur(t) and m outputs y1(t), y2(t), p , ym(t).

Define n outputs of the integrators as state variables: x1(t), x2(t), p , xn(t) Then the

system may be described by

(2–8)

n(t) = fnAx1, x2, p , xn; u1, u2, p , ur ; tB

2(t) = f2Ax1, x2, p , xn; u1, u2, p , ur ; tB

1(t) = f1Ax1, x2, p , xn; u1, u2, p , ur ; tB

Openmirrors.com

Section 2–4 / Modeling in State Space 31

The outputs y1(t), y2(t), p , ym(t) of the system may be given by

(2–9)
If we define

ym(t) = gmAx1, x2, p , xn; u1, u2, p , ur ; tB

y2(t) = g2Ax1, x2, p , xn; u1, u2, p , ur ; tB

y1(t) = g1Ax1, x2, p , xn; u1, u2, p , ur ; tB

u(t) = F

u1(t)

u2(t)

ur(t)

g(x, u, t) = F V

g1Ax1, x2, p , xn; u1, u2, p , ur ; tB

g2Ax1, x2, p , xn; u1, u2, p , ur ; tB

gmAx1, x2, p , xn; u1, u2, p , ur ; tB

y(t) = F V ,

y1(t)

y2(t)
ym(t) V ,

f(x, u, t) = F

f1Ax1, x2, p , xn; u1, u2, p , ur ; tB

f2Ax1, x2, p , xn; u1, u2, p , ur ; tB

fnAx1, x2, p , xn; u1, u2, p , ur ; tB

x(t) = F V,

x1(t)

x2(t)

xn(t) V ,

then Equations (2–8) and (2–9) become

(2–10)

(2–11)

where Equation (2–10) is the state equation and Equation (2–11) is the output equation.

If vector functions f and/or g involve time t explicitly, then the system is called a time-

varying system.
If Equations (2–10) and (2–11) are linearized about the operating state, then we

have the following linearized state equation and output equation:

(2–12)

(2–13)

where A(t) is called the state matrix, B(t) the input matrix, C(t) the output matrix, and

D(t) the direct transmission matrix. (Details of linearization of nonlinear systems about

y(t) = C(t)x(t) + D(t)u(t)

(t) = A(t)x(t) + B(t)u(t)

y(t) = g(x, u, t)

(t) = f(x, u, t)

32 Chapter 2 / Mathematical Modeling of Control Systems

u(t)

y(t)

Figure 2–15

Mechanical system.

u(t)
D(t)

B(t)

A(t)

C(t)

x(t) y(t) •

Údt

x(t)

++ +

Figure 2–14

Block diagram of the

linear, continuous-

time control system

represented in state

space.

the operating state are discussed in Section 2–7.) A block diagram representation of

Equations (2–12) and (2–13) is shown in Figure 2–14.

If vector functions f and g do not involve time t explicitly then the system is called a

time-invariant system. In this case, Equations (2–12) and (2–13) can be simplified to

(2–14)

(2–15)
Equation (2–14) is the state equation of the linear, time-invariant system and Equation

(2–15) is the output equation for the same system. In this book we shall be concerned

mostly with systems described by Equations (2–14) and (2–15).

In what follows we shall present an example for deriving a state equation and output

equation.

EXAMPLE 2–2 Consider the mechanical system shown in Figure 2–15. We assume that the system is
linear. The

external force u(t) is the input to the system, and the displacement y(t) of the mass is the output.

The displacement y(t) is measured from the equilibrium position in the absence of the external

force. This system is a single-input, single-output system.

From the diagram, the system equation is

(2–16)

This system is of second order.This means that the system involves two integrators. Let us define

state variables x1(t) and x2(t) as

Then we obtain

or

(2–17)

(2–18)

The output equation is

y = x (2–19) 1

2=-k

m x1 - b
m x2 +

mu

1 = x2

2=1

m A-ky - by#

B+

mu

1 = x2

x2(t) = y

(t)

x1(t) = y(t)

my$ + by# + ky = u

(t) = Cx(t) + Du(t)

(t) = Ax(t) + Bu(t)

Openmirrors.com
In a vector-matrix form, Equations (2–17) and (2–18) can be written as

(2–20)

The output equation, Equation (2–19), can be written as

(2–21)

Equation (2–20) is a state equation and Equation (2–21) is an output equation for the system.

They are in the standard form:

where

Figure 2–16 is a block diagram for the system. Notice that the outputs of the integrators are state

variables.

Correlation Between Transfer Functions and State-Space Equations. In what

follows we shall show how to derive the transfer function of a single-input, single-output

system from the state-space equations.

Let us consider the system whose transfer function is given by

(2–22)

This system may be represented in state space by the following equations:

(2–23)

y = Cx + Du (2–24)

# = Ax + Bu

Y(s)

U(s) = G(s)