Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 51 views

    Fault Code: 134 Remote Accelerator Position Sensor: CELECT™-Type Accelerator Pedal or Lever

    Uploaded by

    Dung Pham

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Fault Code: 134 Remote Accelerator Position Sensor: CELECT™-Type Accelerator Pedal or Lever

    Uploaded by

    Dung Pham
    51 views2 pages

    Original Title

    134

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    51 views2 pages

    Fault Code: 134 Remote Accelerator Position Sensor: CELECT™-Type Accelerator Pedal or Lever

    Uploaded by

    Dung Pham

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    9/21/22, 12:01 PM QuickServe Online | (3666113) 

      QSK19, QSK23, QSK45, QSK60, and QSK78 Electronic Control System Troubleshooting and R…

    (/qs3/pubsys2/xml/en/manual/3666113/3666113-titlepage.html)

    Fault Code: 134


    Remote Accelerator Position Sensor: CELECT™-Type Accelerator
    Pedal or Lever

    Overview
    Codes Reason Effect
    Fault Code: 134
    Less than 0.12 VDC
    PID(P): P29
    detected at the remote
    Calibration-dependent
    SPN: 029
    accelerator pedal or lever
    power and speed derate.
    FMI: 4
    position signal pin 30 of the
    Lamp: Red
    OEM interface harness.
    SRT: 00-386

    Remote Accelerator Position Sensor: CELECT™-Type Accelerator Pedal or Lever

    Circuit Description

    https://quickserve.cummins.com/qs3/portal/service/manual/en/3666113/ 1/2
    9/21/22, 12:01 PM QuickServe Online | (3666113)   QSK19, QSK23, QSK45, QSK60, and QSK78 Electronic Control System Troubleshooting and R…

    The remote accelerator pedal or lever provides the operator's accelerator command to the ECM
    through the OEM harness and OEM
    interface harness. The ECM uses this signal to determine
    the fueling command for the fuel rail actuator valve.

    Component Location
    The accelerator pedal or lever location varies with each OEM. Refer to the OEM manual.

    Shoptalk
    The remote accelerator pedal or lever position sensor is a potentiometer. The resistance
    specifications of the remote accelerator
    pedal or lever position sensor are the following:

    Between the supply and the return = 2000 to 3000 ohms

    Between the supply and the signal: Released = 1500 to 3000 ohms. Depressed = 200 to
    1500 ohms.
    Note: If the accelerator pedal or lever or remote accelerator pedal or lever position sensor is
    changed, or after a calibration
    download, cycle the accelerator pedal or lever (turn keyswitch ON)
    through its complete travel 3 times. This procedure calibrates
    the new accelerator pedal or lever
    with the ECM.

    Refer to Troubleshooting Fault Code t05-134 (/qs3/pubsys2/xml/en/procedures/19/19-t05-134.html)

    Last Modified:  01-Mar-2011

    https://quickserve.cummins.com/qs3/portal/service/manual/en/3666113/ 2/2

    You might also like