Manual de Servicio Aire Acondicionado LG

website http://biz.LGservice.
com
LG
LG
Room Air Conditioner
SERVICE MANUAL
MODELS: AS-H0766KA2 LS-H0766KA2
AS-H0966KA2 LS-C0966KA2
AS-H126RKA2 LS-H0966KA2
AS-H186TKA2 LS-C126RKA2
LS-H246TKA2 LS-H126RKA2
CAUTION
• BEFORE SERVICING THE UNIT, READ THE SAFETY
PRECAUTIONS IN THIS MANUAL.
• ONLY FOR AUTHORIZED SERVICE PERSONNEL.
Downloaded from www.Manualslib.com manuals search engine

Air Conditioner Service Manual
TABLE OF CONTENTS
LG Model Name ...............................................................................................................................................3
Safety Precautions..........................................................................................................................................5
Dimensions....................................................................................................................................................10
Symbols Used in this Manual ...................................................................................................................10
Indoor Unit................................................................................................................................................10
Outdoor Unit.............................................................................................................................................11
Product Specifications .................................................................................................................................14
Installation .....................................................................................................................................................16
Selection of the Best Location..................................................................................................................16
Piping Length and Elevation.....................................................................................................................16
How to Fix Installation Plate .....................................................................................................................17
Drill a Hole in the Wall ..............................................................................................................................17
Drain hose junction...................................................................................................................................17
Flaring work and connection of piping .......................................................................................................18
Flaring work..............................................................................................................................................18
Connection of Piping Indoor.....................................................................................................................18
Connection of the Pipes-Outdoor.............................................................................................................22
Connecting the cable between indoor unit and outdoor unit ...................................................................23
Connect the Cable to the Indoor Unit. ......................................................................................................23
Connect the Cable to the Outdoor Unit ....................................................................................................24
Checking the drainage and forming the pipings........................................................................................25
Checking the Drainage.............................................................................................................................25
Form the Piping ........................................................................................................................................25
AIR PURGING ................................................................................................................................................26
Air purging................................................................................................................................................26
Air purging with vacuum pump .................................................................................................................26
Test Running .................................................................................................................................................28
Operation .......................................................................................................................................................29
Function of Controls .................................................................................................................................29
Display Function ......................................................................................................................................33
Self-diagnosis Function............................................................................................................................33
Remote Control Operations......................................................................................................................34
Disassembly ..................................................................................................................................................35
Indoor Unit................................................................................................................................................35
Schematic Diagram.......................................................................................................................................38
Electric Control Device .............................................................................................................................38
Wiring Diagram.........................................................................................................................................39
Components Location ..............................................................................................................................40
Troubleshooting Guide .................................................................................................................................42
Refrigeration Cycle Diagram ....................................................................................................................42
2-way, 3-way Valve .................................................................................................................................43
Cycle Parts...............................................................................................................................................49
Electronic Parts ........................................................................................................................................50
Exploded View...............................................................................................................................................57
Replacement Parts List ................................................................................................................................62
2 Room Air Conditioner

LG Model Name
2003
1 2 - 3 4 5 6 7 8 9 10
Code Type Code of Model Meaning
1 Producing Center, A~Z L: Chang-won R22 N: India

Refrigerant A: Chang-won R410A Z: Brazil
C: Chang-won R407C D: Indonesia
T: China M: Mexico
K: Turkey R22 V: Vietnam
E: Turkey R410A S: Out Sourcing
H: Thailand
2 Product Type A~Z S: Split Type Air Conditioner
3 Cooling/Heating/Inverter A~Z C: Cooling only V: AC Inverter C/O

H: Heat pump N: AC Inverter H/P
X: C/O + E/Heater Q: DC Inverter C/O
Z: H/P + E/Heater W: DC Inverter H/P
4, 5 Capacity 0~9 Cooling/Heating Capacity

Ex. "09" → 9,000 Btu/h
6 Electric Range 1~9 1: 115V/60Hz, A: 220V, 50Hz, 3Phase

A~Z 2: 220V/60Hz B: 208~230V, 60Hz, 3Phase
3: 208-230V/60Hz C: 575V, 50Hz, 3Phase
5: 200-220V/50Hz D: 440~460, 60Hz, 3Phase
6: 220-240V/50Hz E: 265V, 60Hz
7: 110V, 50/60Hz F: 200V, 50/60Hz
8: 380-415V/50Hz
9: 380-415V/60Hz
7 Chassis A~Z Name of Chassis of Unit

Ex. LSP → SP Chassis
8 Look A~Z Look,

Color (Artcool Model)
9 Function A~Z Basic A
Basic+4Way B
Plasma Filter C
Plasma Filter+4 Way D
Tele+LCD E
Tele+LCD+Nano plasma+4Way F
Nano Plasma F+(A/changeove)+A/clean+Low A G
Nano Plasma F+(A/changeove)+A/clean+4way+Low A H
Tele+LED+4way I
Internet J
Plasma F+4Way+Oxy generator K
Nano Plasma F+(A/changeove)+A/clean L
Nano Plasma F+(A/changeove)+A/clean+4way M
Nano Plasma F+(A/changeove)+A/clean+PTC N
Nano Plasma F+(A/changeove)+Autoclean+4way+PTC P
Nano Plasma F+(A/changeove)+A/clean+4way+Low A+PTC Q
Negative ION+A/Clean R
(Nano)Plasma+Negative ION+A/Clean S
4way+(Nano)Plasma F+Negative ION+Healthy dehumidification+A/Clean T
Nano Plasma F+4Way+(A/changeove)+A/clean+ U
10 Serial No. 1~9 LG Model Development Serial No.
* ARTCOOL COLOR
R Mirror
W White
B Blue
D Wood
M Metal
C Cherry
Service Manual 3

2004~
1 2 - 3 4 5 6 7 8 9 10
Code Type Code of Model Meaning
1 Producing Center, A~Z L: Chang-won R22 N: India

Refrigerant A: Chang-won R410A Z: Brazil
C: Chang-won R407C D: Indonesia
T: China M: Mexico
K: Turkey R22 V: Vietnam
E: Turkey R410A S: Out Sourcing
H: Thailand
2 Product Type A~Z S: Split Type Air Conditioner
3 Cooling/Heating/Inverter A~Z C: Cooling only V: AC Inverter C/O

H: Heat pump N: AC Inverter H/P
X: C/O + E/Heater Q: DC Inverter C/O
Z: H/P + E/Heater W: DC Inverter H/P
4, 5 Capacity 0~9 Cooling/Heating Capacity
Ex. "09" → 9,000 Btu/h
6 Electric Range 1~9 1: 115V/60Hz, A: 220V, 50Hz, 3Phase
A~Z 2: 220V/60Hz B: 208~230V, 60Hz, 3Phase
3: 208-230V/60Hz C: 575V, 50Hz, 3Phase
5: 200-220V/50Hz D: 440~460, 60Hz, 3Phase
6: 220-240V/50Hz E: 265V, 60Hz
7: 110V, 50/60Hz F: 200V, 50/60Hz
8: 380-415V/50Hz
9: 380-415V/60Hz CHASSIS Look Division
7 Chassis A~Z Name of Chassis of Unit S4/S5 D Panel Type(Deluxe)
S6 K Fighting 'Look'
Ex. LSP → SP Chassis
SQ L (LG1)
8 Look A~Z Look, SR G (LG2)-SEMI PANEL
Color (Artcool Model) ST M OEM1
ST2 N OEM2
D Panel Type(Deluxe)
P LG3
9 Function A~Z Basic A

Basic+4Way B
Plasma Filter C
Plasma Filter+4 Way D
Tele+LCD E
Tele+LCD+Nano plasma+4Way F
Nano Plasma F+(A/changeove)+A/clean+Low A G
Nano Plasma F+(A/changeove)+A/clean+4way+Low A H
Tele+LED+4way I
Internet J
Plasma F+4Way+Oxy generator K
Nano Plasma F+(A/changeove)+A/clean L
Nano Plasma F+(A/changeove)+A/clean+4way M
Nano Plasma F+(A/changeove)+A/clean+PTC N
Nano Plasma F+(A/changeove)+Autoclean+4way+PTC P
Nano Plasma F+(A/changeove)+A/clean+4way+Low A+PTC Q
Negative ION+A/Clean R
(Nano)Plasma+Negative ION+A/Clean S
4way+(Nano)Plasma F+Negative ION+Healthy dehumidification+A/Clean T
Nano Plasma F+4Way+(A/changeove)+A/clean+ U
10 Serial No. 1~9 LG Model Development Serial No.

* ARTCOOL COLOR
R Mirror
W White
B Blue
D Wood
M Metal
C Cherry

Safety Precautions
Safety Precautions
To prevent injury to the user or other people and property damage, the following instructions must
be followed.
■ Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classified by the following indications.
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to properties only.

■ Meanings of symbols used in this manual are as shown below.
Be sure not to do.
Be sure to follow the instruction.
■ Installation
Do not use damaged power cords, plugs, or a Always use the power plug and socket with the
loose socket. ground terminal.
• There is risk of fire of electric shock. • There is risk of electric shock.
Install the panel and the cover of control box .Do not modify or extend the power cord.
securely.
• There is risk of fire of electric shock. • No grounding may cause electric shock.
Service Manual 5

Safety Precautions
For re-installation of the installed product, Do not install, remove, or re-install the unit by
always contact a dealer or an authorized ser- yourself.
vice center.
• There is risk of fire, electric shock, explosion, or • There is risk of fire, electric shock, explosion, or
injury. injury.
Be cautious when unpacking and installing the For installation, always contact the dealer or
product. an Authorized service center
• Sharp edges could cause injury. Be especially care- • There is risk of fire, electric shock, explosion, or injury.
ful of the case edges and the fins on the condenser
and evaporator.
Do not install the product on a defective instal- Be sure the installation area does not
lation stand. deteriorate with age.
• It may cause injury, accident, or damage to the • If the base collapses, the air conditioner could fall
product. with it, causing property damage, product failure,
and personal injury.

Safety Precautions
■ Operation
Do not turn the air-conditioner ON or OFF by Use a dedicated outlet for this appliance.
plugging or unplugging the power plug.
• There is risk of fire or electrical shock. • There is risk of fire or electrical shock.
Grasp the plug to remove the cord from the Do not place a heater or other appliances near
outlet. Do not touch it with wet hands. the power cable.
• There is risk of fire or electrical shock. • There is risk of fire and electric shock.
Do not allow water to run into electrical parts. Do not store or use flammable gas or com-
bustibles near the air conditioner.
• There is risk of fire, failure of the product, or electric • There is risk of fire or failure of product.
shock.
x
Wa Thinner
Service Manual 7

Safety Precautions
Unplug the unit if strange sounds, odors, or Be cautious that water could not enter the
smoke comes from it. product.
• There is risk of electric shock or fire. • There is risk of fire, electric shock, or product dam-
age.
■ Installation
Always check for gas (refrigerant) leakage after Install the drain hose to ensure that water is
installation or repair of product. drained away properly.
• Low refrigerant levels may cause failure of product. • A bad connection may cause water leakage.
Keep level even when installing the product. Use two or more people to lift and transport
the air conditioner.
• To avoid vibration or water leakage. • Avoid personal injury.
90˚

Safety Precautions
■ Operation
Use a soft cloth to clean. Do not use harsh Do not touch the metal parts of the product
detergents, solvents, etc. when removing the air filter. They are very
sharp!
• There is risk of fire, electric shock, or damage to the • There is risk of personal injury.
plastic parts of the product.
x
Wa
Do not step on or put anyting on the product. Do not insert hands or other objects through
(outdoor units) the air inlet or outlet while the air conditioner
is plugged in.
• There is risk of personal injury and failure of product. • There are sharp and moving parts that could cause
personal injury.
Service Manual 9

Dimensions
Dimensions
Symbols Used in this Manual
This symbol alerts you to the risk of electric shock.
This symbol alerts you to hazards that could cause harm to the
air conditioner.
NOTICE This symbol indicates special notes.
Indoor Unit
D
W
Installation plate
Model
7K, 9K Btu Series 12K Btu Series 18K Btu Series
Dimension
W mm 756 900 1,090
H mm 260 285 314
D mm 155 156 172

Dimensions
Outdoor Unit
W L2
L1
D
L3
H
Gas side
(3-way valve)
L5
Liquid side
L4
(2-way valve)
MODEL
7k, 9k Btu Series 12k Btu Series
DIM unit
W mm 575 717
H mm 525 498
D mm 260 229
L1 mm 301 270
L2 mm 73 56
L3 mm 392 464
L4 mm 35 17
L5 mm 100 130
Service Manual 11

Dimensions
Outdoor Unit
W L2
L1
D
L3
H
L5 Gas side
(3-way valve)
Liquid side
L4
(2-way valve)
MODEL
18K But Series
DIM
W mm 840
H mm 577
D mm 276
L1 mm 337
L2 mm 64
L3 mm 611
L4 mm 16
L5 mm 156

Dimensions
Outdoor Unit
W
L2
L1
D
L3
L4
H
L11 L10
Gas side
Liquid side
L7 L6 L8 L9
L5
MODEL
AS-H246TKA2
DIM
W mm 870
H mm 655
D mm 320
L1 mm 370
L2 mm 340
L3 mm 25
L4 mm 630
L5 mm 25
L6 mm 546
L7 mm 162
L8 mm 162
L9 mm 54
L10 mm 74.5
L11 mm 79
Service Manual 13

Product Specifications
Table-1
Model Name
AS-H0766KA2 AS-H0966KA2 AS-H126RKA2 AS-H186TKA2 AS-H246TKA2
Item Unit
Cooling Capacity 7000 9000 12000 18500 23500
Btu/h
Heating Capacity 7300 9300 12500 19000 23500
Moisture Removal l/h 1 1.2 1.2 2.2 2.9
Power Source Ø, V, Hz 1Ø,220-240V,50Hz 1Ø,220-240V,50Hz 1Ø,220-240V,50Hz 1Ø,220-240V,50Hz 1Ø,220-240V,50Hz
Indoor 5.0/5.7 5.8/6.6 8.8/9.5 13.4 15.1
Air Circulation m3/min
Outdoor 20 20 22 42 42
Indoor 34 37 40 40 47
Noise Level dB (A)±3
Outdoor 49 49 52 54 57
Cooling 730 940 1250 1760 2290
Input W
Heating 730 970 1140 1900 2450
Running Cooling 3.2 4.1 5.6 7.9 10.5
A
Current Heating 3.2 4.2 5.1 8.5 11.0
E.E.R. Cooling 9.59 9.57 9.6 10.51 10.26
Btu/hW
C.O.P Heating 10.0 9.58 10.96 10.0 9.59
Indoor 7 7 9.5 22 22
Motor Output W
Outdoor 18 18 - 72 82.9
Dimensions Indoor 756x260x155 756x260x155 900x285x156 1090x314x172 1090x314x172
mm
(W x H x D) Outdoor 575x525x260 575x525x260 717x498x229 870x577x276 870x577x276
Indoor 7 7 7.2 12 12
Net. Weight kg
Outdoor 25 26 30 50 60
Refrigerant (R410A) g 660g 710g 720g 1270g 1500g
Airflow Direction Control (Up & Down) O O O O O
Airflow Direction Control (Left & Right) - - - - -
Chaos Wind O O O O O
Timer 7Hr OFF 7Hr OFF 7Hr OFF 7Hr OFF 7Hr OFF
Self Diagnosis O O O O O
Remocon Type L.C.D wireless L.C.D wireless L.C.D wireless L.C.D Wireless L.C.D Wireless
Liquid 1/4"(6.35) 1/4"(6.35) 1/4"(6.35) 1/4"(6.35) 3/8”(9.52)
Service Valve inch(mm)
Gas 3/8"(9.52) 3/8"(9.52) 1/2"(12.7) 5/8"(15.88) 5/8”(15.88)
Sleeping Operation - - - - -
Drain Hose O O O O O
Connecting Cable 1.0mm x 3, 0.75mm x 2 1.0mm x 3, 0.75mm x 2 1.0mm x 3, 0.75mm x 2 1.5mm x 3, 0.75mm x 2 12.5mm x 3, 0.75mm2 x 2
2 2 2 2 2 2 2 2 2
Power Cord 1.0mm2 1.0mm2 1.0mm2 3 x 1.5mm2 3 x 2.5mm2

Table-2
Model Name
LS-H0766KA2 LS-H0966KA2 LS-H126RKA2 LS-C126RKA2 LS-C0966KA2
Item Unit
Cooling Capacity 7000 9000 12000 12000 9000
Btu/h
Heating Capacity 7300 9000 13000 - -
Moisture Removal l/h 1 1.2 1.2 1.2 1.2
Power Source Ø, V, Hz 1Ø,220-240V,50Hz 1Ø,220-240V,50Hz 1Ø,220-240V,50Hz 1Ø,220-240V,50Hz 1Ø,220-240V,50Hz
Indoor 5.0/5.7 5.8/6.6 8.8/9.5 8.8/9.5 5.8/6.6
Air Circulation m3/min
Outdoor 20 20 22 22 20
Indoor 35 37 40 40 37
Noise Level dB (A)±3
Outdoor 49 49 52 52 49
Cooling 700 920 1310 1310 950
Input W
Heating 730 850 1250 - -
Running Cooling 3.1 4.1 6.0 6.0 4.2
A
Current Heating 3.2 3.7 5.8 - -
E.E.R. Cooling 10 9.78 9.16 9.16 9.47
Btu/hW
C.O.P Heating 2.93 3.1 3.05 - 3.1
Indoor 7 7 9.5 9.5 7
Motor Output W
Outdoor 18 18 - - 18
Dimensions Indoor 756x260x155 756x260x155 900x285x156 900x285x156 756x260x155
mm
(W x H x D) Outdoor 575x525x260 575x525x260 717x498x229 717x498x229 575x525x260
Indoor 7 7 7.2 7.2 7
Net. Weight kg
Outdoor 25 26 30 30 26
Refrigerant (R410A) g 650g 690g 800g 670g 690g
Airflow Direction Control (Up & Down) O O O O O
Airflow Direction Control (Left & Right) - - - - -
Chaos Wind O O O O O
Timer 7Hr OFF 7Hr OFF 7Hr OFF 7Hr OFF 7Hr OFF
Self Diagnosis O O O O O
Remocon Type L.C.D wireless L.C.D wireless L.C.D wireless L.C.D wireless L.C.D wireless
Liquid 1/4"(6.35) 1/4"(6.35) 1/4"(6.35) 1/4"(6.35) 1/4"(6.35)
Service Valve inch(mm)
Gas 3/8"(9.52) 3/8"(9.52) 1/2"(12.7) 1/2"(12.7) 3/8"(9.52)
Sleeping Operation - - - - -
Drain Hose O O O O O
Connecting Cable 1.0mm x 3, 0.75mm x 2
2 2
1.0mm x 3, 0.75mm x 2
2 2
1.0mm x 3, 0.75mm x 2
2 2
1.0mm x 3, 0.75mm x 2
2 2
1.0mm x 3, 0.75mm2 x 2
2
Power Cord 1.0mm2 1.0mm2 1.0mm2 1.0mm2 1.0mm2
Service Manual 15

Installation
Installation
Selection of the Best Location
Indoor unit Rooftop Installations:
• Do not have any heat or steam near the unit. • If the outdoor unit is installed on a roof structure, be
• Select a place where there are no obstacles in front of the sure to level the unit. Ensure the roof structure and
unit. anchoring method are adequate for the unit location.
• Consult local codes regarding rooftop mounting.
• Make sure that condensation drainage can be conveniently
routed away.
Do not install near a doorway. Piping Length and Elevation
• Ensure that the space around the left and right of the unit is
more than "A". The unit should be installed as high on the Capacit Pipe Size Standard Max. Max. Additional
wall as possible, allowing a minimum of "B" from ceiling. y Length Elevation Length Refrigerant
(Btu/h) GAS LIQUID (m) B (m) A (m) (g/m)
• Use a stud finder to locate studs to prevent unnecessary 3/8"(Ø9.52) 1/4"(Ø6.35) 4 or 7.5 7 15 20
damage to the wall. 5k~14k
1/2"(Ø12.7) 1/4"(Ø6.35) 4 or 7.5 7 15 20
More than "B" More than "A" 1/2"(Ø12.7) 1/4"(Ø6.35) 4 or 7.5 15 30 20
18k~28k 5/8"(Ø15.88) 1/4"(Ø6.35) 4 or 7.5 15 30 20
5/8"(Ø15.88) 3/8"(Ø9.52) 4 or 7.5 15 30 30
5/8"(Ø15.88) 3/8"(Ø9.52) 7.5 15 30 30
30k~38k
3/4"(Ø19.05) 3/8"(Ø9.52) 7.5 15 30 50
More than 2.3m More than "B"

Outdoor unit Indoor unit
Install the indoor unit on the wall where the height

A A
from the floors more than 2.3 meters.
Indoor unit B B
Clearance(cm) Outdoor unit
Grade
A B
5K~28K 10 5
30K~38K 30 12
I
Outdoor unit
Outdoor unit
• If an awning is built over the unit to prevent direct sunlight
A
or rain exposure, make sure that heat radiation from the Oil trap
condenser is not restricted.
Indoor unit
• Ensure that the space around the back and sides is more B
than 10cm. The front of the unit should have more than
70cm of space.
• Do not place animals and plants in the path of the warm air.
• Take the air conditioner weight into account and select a
If case more than 5m
place where noise and vibration are minimum.
• Select a place so that the warm air and noise from the air
conditioner do not disturb neighbors.
More than 60cm • Capacity is based on standard length and maxi-
mum allowance length is on the basis of reliability.
More than 10cm More than 10cm • Oil trap should be installed every 5~7 meters.
More
More than 70cm than 60cm

Installation
How to Fix Installation Plate Drill a Hole in the Wall

The wall you select should be strong and solid • Drill the piping hole with a ø70mm hole core drill.
enough to prevent vibration Drill the piping hole at either the right or the left
with the hole slightly slanted to the outdoor side.
1. Mount the installation plate on the wall with four
type A screws. If mounting the unit on a concrete WALL
wall, use anchor bolts.
Indoor Outdoor
• Mount the installation plate horizontally by aligning
the centerline using a level.
(3/16"~5/16")
Installation Plate
5-7mm
• Open the Front Grille.
• Pass Telephone Control Cord Wire through the hole
Type "A" screw
which the power cord goes through.
2. Measure the wall and mark the centerline. It is • Connect Telephone Control Cord Wire to the phone jack
also important to use caution concerning the of telephone PCB of Control Box.
location of the installation plate-routing of the • Fix Telephone Control Cord Wire inside Control box so
wiring to power outlets is through the walls typi- as not to disconnect.
cally. Drilling the hole through the wall for pip- • Close the Front Grille.
ing connections must be done safely.
Drain hose junction

• Remove the rubber stopple in the desired drain direc-
C tion.
Installation plate
• Insert drain hose into the handle of drain pan, and join
D
A drain hose and connecting hose according to the figure

Ø70mm Ø70mm
by.
Left rear piping Right rear piping
CHASSIS Distance (mm)

(Grade) A B C D
S6 75 12 80 12
SR2 0 40 20 40
ST2 105 0 210 0
Installation plate
B
D
Adhesive
C E A
Right rear piping Ø70mm Only the

Left rear piping desired direction
Connecting
part
CHASSIS Distance (mm) Drain
hose
(Grade) A B C D E
SM 180 115 - 115 50
SN 180 115 195 115 -
Service Manual 17

Flaring work and connection of piping

Flaring work • Carry out flaring work using flaring tool as shown below.
Outside diameter A
Flaring work
mm inch mm
Main cause for refrigerant leakage is due to defect in the
flaring work. Carry out correct flaring work using the follow- Ø6.35 1/4 0~0.5
ing procedure. Ø9.52 3/8 0~0.5
Ø12.7 1/2 0~0.5
Cut the pipes and the cable.
• Use the piping kit accessory or pipes purchased locally. Ø15.88 5/8 0~1.0
• Measure the distance between the indoor and the outdoor unit. Ø19.05 3/4 1.0~1.3
• Cut the pipes a little longer than the measured distance.
• Cut the cable 1.5m longer than the pipe length. Check
• Compare the flared work with figure below.
Copper
pipe Slanted Uneven Rough
90° • If flare is noted to be defective, cut off the flared sec-
tion and re-flare it.
Smooth all round
Inside is shiny without scratches
Burr removal = Improper flaring =

• Completely remove all burrs from the cut cross section of
pipe/tube.
• Put the end of the copper tube/pipe in a downward direc- Inclined Surface Cracked Uneven
damaged thickness
Even length
tion as you remove burrs in order to avoid dropping burrs all round
into the tubing.
Pipe
Reamer
Connection of piping -- Indoor
• Preparing the indoor unit's piping and drain hose for instal-
Point down
lation through the wall.
• Remove the plastic tubing retainer(see illustration below)
Putting nut on and pull the tubing and drain hose away from chassis.
• Replace the plastic tubing holder in the original
• Remove flare nuts attached to indoor and outdoor unit,
position.(Optional)
then put them on pipe/tube having completed burr removal.
(not possible to put them on after flaring work)
Flare nut
Copper tube
Tubing holder
Flaring work
• Firmly hold copper pipe in a die in the dimension shown in
the table above.
Handle When install, make sure that the
"A"
Bar Bar remaining parts must be removed

Yoke clearly so as not to damage the pip-
Cone ing and drain hose, especially power
cord and connecting cable.
Copper pipe
Clamp handle
Red arrow mark

For right rear piping Connecting the pipings to the indoor unit and
drain hose to drain pipe.
Route the indoor tubing and the drain hose in the direction of
• Align the center of the pipes and sufficiently tighten
rear right.
the flare nut by hand.
Drain hose
Indoor unit tubing Flare nut Pipes
• Tighten the flare nut with a wrench.
Insert the connecting cable into the indoor unit from the out- Open-end wrench (fixed)
door unit through the piping hole.
Flare nut
• Do not connect the cable to the indoor unit.
Wrench Connection pipe
• Make a small loop with the cable for easy connection later.
Indoor unit tubing
Outside diameter Torque

Tape the tubing, drain hose, and the connecting cable. Be
mm inch kg.m
sure that the drain hose is located at the lowest side of the
Ø6.35 1/4 1.8
bundle. Locating at the upper side can cause drain pan to
Ø9.52 3/8 4.2
overflow inside the unit.
Ø12.7 1/2 5.5
Ø15.88 5/8 6.6
Ø19.05 3/4 6.6
• When extending the drain hose at the indoor unit, install the
drain pipe.
Tape
Connecting Drain pipe
pipe
Drain hose
Connecting cable Indoor unit drain hose
NOTE: If the drain hose is routed inside the room, insulate Adhesive
Vinyl tape(narrow)
the hose with an insulation material* so that dripping from Wrap the insulation material around the con-
"sweating"(condensation) will not damage furniture or floors.
necting portion.
*Foamed polyethylene or equivalent is recommended.
•Overlap the connection pipe insulation material and the
Indoor unit installation indoor unit pipe insulation material. Bind them together with
vinyl tape so that there is no gap.
• Hook the indoor unit onto the upper portion of the installa- Plastic bands Insulation material
tion plate.(Engage the two hooks of the rear top of the
indoor unit with the upper edge of the installation plate.)
Ensure that the hooks are properly seated on the installa-
tion plate by moving it left and right.
• Wrap the area which accommodates the rear piping hous-
Connecting ing section with vinyl tape.
cable
Connection Indoor
pipe unit pipe
Drain hose Vinyl tape Wrap with vinyl tape
(wide)
Press the lower left and right sides of the unit against the Connecting cable
installation plate until the hooks engage into their slots(click-
ing sound). Pipe
Vinyl tape(narrow)
Service Manual 19

• Bundle the piping and drain hose together by wrapping Connecting the pipings to the indoor unit and
them with vinyl tape for enough to cover where they fit into the drain hose to drain pipe.
the rear piping housing section.
• Align the center of the pipes and sufficiently tighten the
Wrap with vinyl tape
flare nut by hand.
Pipe
Vinyl tape(wide)
Drain hose Indoor unit tubing Flare nut Pipes
For left rear piping • Tighten the flare nut with a wrench.
Route the indoor tubing and the drain hose to
the required piping hole position. Open-end wrench (fixed)
Flare nut
Wrench Connection pipe
Indoor unit tubing

mm inch kg.m
Insert the piping, drain hose, and the connect- Ø6.35 1/4 1.8
ing cable into the piping hole. Ø9.52 3/8 4.2
Ø12.7 1/2 5.5
Connecting cable Ø15.88 5/8 6.6
Drain pipe Ø19.05 3/4 6.6
• When extending the drain hose at the indoor unit, install the
drain pipe.
Insert the connecting cable into the indoor unit.
• Don't connect the cable to the indoor unit.
Drain hose
• Make a small loop with the cable for easy connection later.
Tape the drain hose and the connecting cable.
Indoor unit drain hose
• Connecting cable
Vinyl tape (narrow)
Adhesive
Wrap the insulation material around the con-

necting portion.
• Overlap the connection pipe heat insulation and the indoor
unit pipe heat insulation material. Bind them together with
vinyl tape so that there is no gap.
Indoor unit installation Plastic bands Insulation material
• Hang the indoor unit from the hooks at the top of the instal-
lation plate.
• Insert the spacer etc. between the indoor unit and the
installation plate and separate the bottom of the indoor unit
from the wall.
Indoor unit
Spacer
Installation plate
8cm

• Wrap the area which accommodates the rear piping hous- Indoor unit installation
ing section with vinyl tape.
• Remove the spacer.
Connection Indoor
pipe unit piping • Ensure that the hooks are properly seated on the installa-
Vinyl tape
tion plate by moving it left and right.
Wrap with vinyl tape
(wide)
Pipe
Connecting
Vinyl tape(narrow) cable
Connecting cable
Drain hose
Press the lower left and right sides of the unit against the
installation plate until the hooks engage into their
• Bundle the piping and drain hose together by wrapping slots(clicking sound).
them with cloth tape over the range within which they fit
into the rear piping housing section.
Pipe
Drain hose
Vinyl tape(narrow) Installation Information (For left piping)
• Good case
For left piping. Follow the instruction below.
Wrap with • Press on the upper side of clamp. ( )
vinyl tape(wide)
Reroute the pipings and the drain hose across

the back of the chassis.
• Unfold the tubing to downward slowly. ( )
Piping for
passage through
piping hole
Set the pipings and the drain hose to the back

of the chassis with the tubing holder.
• Hook the edge of tubing holder to tap on chassis and push
the bottom of tubing holder to be engaged at the bottom of
chassis.
• Bend the tubing to the left side of chassis.
Tubing holder
Service Manual 21

Connection of the pipes-Outdoor

• Bad case Align the center of the pipings and sufficiently
• Following bending type from right to left could cause tighten the flare nut by hand.
problem of pipe damage.
Finally, tighten the flare nut with torque wrench

until the wrench clicks.
• When tightening the flare nut with torque wrench, ensure

the direction for tightening follows the arrow on the wrench.
mm inch kg.m
Ø6.35 1/4 1.8
Ø9.52 3/8 4.2
Ø12.7 1/2 5.5
Ø15.88 5/8 6.6
Ø19.05 3/4 6.6
Outdoor unit
Gas side piping
(Bigger diameter)
Liquid side
piping
(Smaller
diameter)
Torque wrench

Connecting the cable between indoor unit and outdoor unit

Connect the cable to the Indoor unit.
• Connect the cable to the indoor unit by connecting the wires to the terminals on the control board individually according to
the outdoor unit connection. (Ensure that the color of the wires of the outdoor unit and the terminal No. are the same as
those of the indoor unit.). The earth wire should be longer than the common wires.
The above circuit diagram is subject to change without notice.
When installing, refer to the circuit diagram on the control box
inside Indoor Uint.
• When installing, refer to the circuit diagram on the The power cord connected to the "A" unit
Control Box of Indoor Unit. should be complied with the following
• When installing, refer to the wiring diagram on the specifications(Type "B" approved by HAR or
SAA).
Control Cover Inside Outdoor Unit.
• The above circuit diagram is subject to change without

notice.
• Be sure to connect wires according to the wiring diagram. (mm2)
Grade
• Connect the wires firmly, so that not to be pulled out easily. NORMAL CROSS
5k~9k 12k 14K~18k 24k~28k 30k, 32k 36k, 38k
• Connect the wires according to color codes by referring the -SECTIONAL AREA
0.75 1.0 1.5 2.5 2.5 5.5
wiring diagram.
Unit(A) Indoor Indoor Indoor Indoor Outdoor Outdoor
Cable Type(B) H05VV-F H05VV-F H05VV-F H05VV-F H05RN-F H05RN-F
• If a power plug is not to be used, provide a circuit The power connecting cable connected to
breaker between power source and the unit as the indoor and outdoor unit should be
shown below. complied with the following specifications
(Type "B" approved by HAR or SAA).
Main power source
NORMAL
CROSS-SECTIONAL
Air Circuit Breaker (mm2) AREA 0.75mm2
Conditioner Use a circuit
NORMAL Grade
breaker or time
CROSS
delay fuse. 5k~12k 14k~18k 24k~28k
-SECTIONAL
AREA 1.0 1.5 2.5
Cable Type(B) H07RN-F H07RN-F H07RN-F
(mm2)
Grade
NORMAL CROSS
30k, 32k 36k, 38k
-SECTIONAL AREA
0.75 0.75
Cable Type(B) H07RN-F H07RN-F
Service Manual 23

Connect the cable to the outdoor unit Outdoor Unit
Remove the control cover from the unit by Terminal block

loosening the screw.
Connect the wires to the terminals on the con- Over 5mm
trol board individually.
Connecting cable
Secure the cable onto the control board with
the cord clamp. Connecting cable
Cover control
Refix the control cover to the original position
with the screw.
Use a recognized circuit breaker "A"

between the power source and the unit.
A disconnecting device to adequately discon-
nect all supply lines must be fitted.
Circuit Grade
Breaker 5k~14k 18k 24k~28k 30k, 32k 36k, 38k
(A)
15 20 30 30 40
After the confirmation of the above conditions, prepare the wiring as follows:
1) Never fail to have an individual power circuit specifically for the air conditioner. As for the method of wiring,
be guided by the circuit diagram posted on the inside of control cover.
2) The screw which fasten the wiring in the casing of electrical fittings are liable to come loose from vibrations
to which the unit is subjected during the course of transportation. Check them and make sure that they are
all tightly fastened. (If they are loose, it could cause burn-out of the wires.)
3) Specification of power source.
4) Confirm that electrical capacity is sufficient.
5) See to that the starting voltage is maintained at more than 90 percent of the rated voltage marked on the
name plate.
6) Confirm that the cable thickness is as specified in the power source specification.
(Particularly note the relation between cable length and thickness. (Refer to page 22))
7) Always install an earth leakage circuit breaker in a wet or moist area.
8) The following would be caused by voltage drop.
• Vibration of a magnetic switch, which will damage the contact point, fuse breaking, disturbance of the normal func-
tion of the overload.
9) The means for disconnection from a power supply shall be incorporated in the fixed wiring and have an air
gap contact separation of at least 3mm in each active(phase) conductors.

Checking the drainage and forming the pipings
Checking the drainage and forming the pipings

Checking the drainage Form the piping
To remove the front panel from the indoor unit. Form the piping by wrapping the connecting
• Set the air direction louvers up-and-down to the portion of the indoor unit with insulation mate-
position(horizontally) by hand. rial and secure it with two kinds of vinyl tapes.
• Remove the securing screws that retain the front panel. • If you want to connect an additional drain hose, the end of
Pull the lower left and right sides of the grille toward you the drain outlet should be routed above the ground. Secure
and lift it off. the drain hose appropriately.
In cases where the outdoor unit is installed
below the indoor unit perform the following.
• Tape the piping, drain hose and connecting cable from
down to up.
Pull the right and
the left side. • Secure the tapped piping along the exterior wall using sad-
dle or equivalent.
Seal small openings
To check the drainage. around pipings with a
gum type sealer.
• Pour a glass of water on the evaporator.
• Ensure the water flows through the drain hose of the indoor Taping
unit without any leakage and goes out the drain exit. Drain
hose
Pipings
Connecting
cable
Trap is required to prevent water

from entering into electrical parts.
In cases where the Outdoor unit is installed

above the Indoor unit perform the following.
• Tape the piping and connecting cable from down to up.
Drain piping
• Secure the taped piping along the exterior wall. Form a trap
• The drain hose should point downward for easy drain flow. to prevent water entering the room.
• Fix the piping onto the wall by saddle or equivalent.
Seal a small opening
Downward slope around the pipings
with gum type sealer.
Trap
• Do not make drain piping.

Accumulated
Do not raise
drain water
Air Tip of drain hose
Less than
dipped in water Trap
50mm gap
Water Water Water

Waving
leakage leakage leakage Ditch
Service Manual 25

Air purgingd
AIR PURGING
Air purging • Do a leak test of all joints of the tubing(both indoor and out-
door) and both gas and liquid side service valves.
Air and moisture remaining in the refrigerant system have Bubbles indicate a leak. Be sure to wipe off the soap with a
undesirable effects as indicated below. clean cloth.
• Pressure in the system rises. • After the system is found to be free of leaks, relieve the
• Operating current rises. nitrogen pressure by loosening the charge hose connector
at the nitrogen cylinder. When the system pressure is
• Cooling(or heating) efficiency drops.
reduced to normal, disconnect the hose from the cylinder.
• Moisture in the refrigerant circuit may freeze and block cap-
illary tubing.
• Water may lead to corrosion of parts in the refrigeration
system. Indoor unit
Therefore, the indoor unit and tubing between the indoor and
outdoor unit must be leak tested and evacuated to remove
any noncondensables and moisture from the system.
Air purging with vacuum pump

Preparation
• Check that each tube(both liquid and gas side tubes) Outdoor unit
between the indoor and outdoor units have been properly
connected and all wiring for the test run has been complet-
ed. Remove the service valve caps from both the gas and
the liquid side on the outdoor unit. Note that both the liquid
and the gas side service valves on the outdoor unit are
kept closed at this stage.
Leak test
Manifold valve
• Connect the manifold valve(with pressure gauges) and dry
nitrogen gas cylinder to this service port with charge hoses.
Pressure
Lo Hi
gauge
Be sure to use a manifold valve for air purging. If it is not

available, use a stop valve for this purpose. The "Hi" knob
of the manifold valve must always be kept close.
Charge hose
• Pressurize the system to no more than 150 P.S.I.G. with
dry nitrogen gas and close the cylinder valve when the
gauge reading reached 150 P.S.I.G. Next, test for leaks
with liquid soap.
To avoid nitrogen entering the refrigerant system in a liquid Nitrogen gas

cylinder(in vertical
state, the top of the cylinder must be higher than its bottom standing position)
when you pressurize the system. Usually, the cylinder is
used in a vertical standing position.

Air purgingd
Soap water method

(1) Remove the caps from the 2-way and 3-way valves. Gas side
(2) Remove the service-port cap from the 3-way valve.

(3) To open the 2-way valve turn the valve stem counter-
clockwise approximately 90°, wait for about 2~3 sec, and
close it. Liquid side
3-way valve
(4) Apply a soap water or a liquid neutral detergent on the (Close)
indoor unit connection or outdoor unit connections by a
soft brush to check for leakage of the connecting points 2-way valve
(Open)
of the piping.
(5) If bubbles come out, the pipes have leakage.
Cap
Evacuation Hexagonal wrench
• Connect the charge hose end described in the preceding

steps to the vacuum pump to evacuate the tubing and
indoor unit.
Confirm the "Lo" knob of the manifold valve is open. Then,
run the vacuum pump.
The operation time for evacuation varies with tubing length Indoor unit
and capacity of the pump. The following table shows the
time required for evacuation.
Required time for evacuation when 30 gal/h vacuum

pump is used
If tubing length is less than 10m (33 ft) if tubing length is longer than 10m (33 ft)
10 min. or more 15 min. or more Outdoor unit
• When the desired vacuum is reached, close the "Lo" knob

of the manifold valve and stop the vacuum pump.
Finishing the job
• With a service valve wrench, turn the valve stem of liquid

side valve counter-clockwise to fully open the valve.
Manifold valve
• Turn the valve stem of gas side valve counter-clockwise to
fully open the valve.
Pressure Lo Hi
• Loosen the charge hose connected to the gas side service gauge
port slightly to release the pressure, then remove the hose.
• Replace the flare nut and its bonnet on the gas side service
port and fasten the flare nut securely with an adjustable Open Close
wrench. This process is very important to prevent leakage
from the system.
• Replace the valve caps at both gas and liquid side service
valves and fasten them tight.
This completes air purging with a vacuum pump.
The air conditioner is now ready to test run.
Vacuum pump
Service Manual 27

Test running
TEST RUNNING
1. Check that all tubing and wiring have been properly con- NOTE: If the actual pressure is higher than shown, the system is
nected. most likely over-charged, and charge should be removed.
2. Check that the gas and liquid side service valves are fully If the actual pressure are lower than shown, the system is
open. most likely undercharged, and charge should be added.
The air conditioner is now ready for use.
Settlement of outdoor unit
PUMP DOWN
• Anchor the outdoor unit with a bolt and nut(ø10mm) tightly
This is performed when the unit is to be relocated or
and horizontally on a concrete or rigid mount. the refrigerant circuit is serviced.
• When installing on the wall, roof or rooftop, anchor the Pump Down means collecting all refrigerant in the outdoor
unit without loss in refrigerant gas.
mounting base securely with a nail or wire assuming the
influence of wind and earthquake. CAUTION:
• In the case when the vibration of the unit is conveyed to the Be sure to perform Pump Down procedure with the unit
hose, secure the unit with an anti-vibration bushing. cooling mode.
Bolt
Pump Down Procedure
1. Connect a low-pressure gauge manifold hose to the
charge port on the gas side service valve.
2. Open the gas side service valve halfway and purge the air
from the manifold hose using the refrigerant gas.
3. Close the liquid side service valve(all the way in).
4. Turn on the unit's operating switch and start the cooling
Tubing connection operation.
Evaluation of the performance 5. When the low-pressure gauge reading becomes 1 to
Operate unit for 15~20 minutes, then check the system 0.5kg/cm2 G(14.2 to 7.1 P.S.I.G.), fully close the gas side
refrigerant charge: valve stem and then quickly turn off the unit. At that time,
1. Measure the pressure of the gas side service valve. Pump Down has been completed and all refrigerant gas
will have been collected in the outdoor unit.
2. Measure the temperature of the intake and discharge of air.
Power-Failure Compensation Function User Selection ON/OFF
3. Ensure the difference between the intake temperature and
the discharge is more than 8°C(46°F) (Cooling) or 1) Operation Sequence
(Heating). Press the forced switch until BUZZER sounds 2 times
(beep~beep~).
Intake temperature
Release the forced switch if BUZZER sounds.
Discharge air
Check the function selection ON/OFF with the operation LED.
2) Checking function-selection ON/OFF

Discharge - Function-Selection ON: One time blinking of operation LED
temperature
would repeat 4 times.
4. For reference; the gas side pressure of optimum condition - Function-Selection OFF: Two times blinking of operation LED
is as below.(Cooling) would repeat 4 times.
Refrigerant Outside ambient The pressure of the gas side

TEMP. service valve.
R-22 35°C (95°F) 4~5kg/cm2G(56.8~71.0 P.S.I.G.)
R-410A 35°C (95°F) 8.5~9.5kg/cm2G(120~135 P.S.I.G.)
Power
button
Open the front
panel upward

Operation
Operation
Function of Controls
• DISPLAY
1) C/O Model
Operation Indicator
• ON while in appliance operation, OFF while in appliance pause.
• Flashing while in disconnection or short in Thermistor. (3 sec off / 0.5 sec on)
Comp. Running Incidator

• While in appliance operation, ON while in outdoor unit compressor running, OFF while in compressor off.
2) H/P Model
Operation Indicator
• ON while in appliance operation, OFF while in appliance pause.
• Flashing while in disconnection or short in Thermistor. (3 sec off / 0.5 sec on)
Defrost Indicator
• OFF except when hot start during heating mode operation or while in defrost control.
■ Cooling Mode Operation

• When the intake air temperature reaches 0.5°C below the setting temp, the compressor and the outdoor fan
stop.
• When it reaches 0.5°C above the setting temp, they start to operate again.
Compressor ON Temp ➲ Setting Temp+0.5°C
Compressor OFF Temp ➲ Setting Temp-0.5°C
• While in compressor running, operating with the airflow speed set by the remote control. While in compressor
not running, operating with the low airflow speed regardless of the setting.
■ Healthy Dehumidification Mode

• When the dehumidification operation input by the remote control is received, the intake air temperature is
detected and the setting temp is automatically set according to the intake air temperature.
26°C ≤ Intake Air Temp ➲ 25°C
24°C ≤ Intake Air Temp<26°C ➲ Intake Air Temp-1°C
18°C ≤ Intake Air Temp<24°C ➲ Intake Air Temp-0.5°C
Intake Air Temp<18°C ➲ 18°C
Service Manual 29

Operation
• While in compressor off, the indoor fan repeats low airflow speed and pause.
• While the intake air temp is between compressor on temp. and compressor off temp., 10-min dehumidification
operation and 4-min compressor off repeat.
Compressor ON Temp. ➲ Setting Temp+0.5°C
Compressor OFF Temp. ➲ Setting Temp-0.5°C
• In 10-min dehumidification operation, the indoor fan operates with the low airflow speed.
■ Heating Mode Operation

• When the intake air temp reaches +3°…above the setting temp, the compressor is turned off. When below
the setting temp, the compressor is turned on.
Compressor ON Temp. ➲ Setting Temp.
Compressor OFF Temp. ➲ Setting Temp.+3°C
• While in compressor on, the indoor fan is off when the indoor pipe temp. is below 20°C, when above 28°C , it
operates with the low or setting airflow speed. When the indoor pipe temp is between 20°C and 28°C, it oper-
ates with Super-Low(while in sleep mode, with the medium airflow speed).
• While in compressor off, the indoor fan is off when the indoor pipe temp is below 33°C, when above 35°C , it
operates with the low airflow speed.
• If overloaded while in heating mode operation, in order to prevent the compressor from OLP operation, the
outdoor fan is turned on/off according to the indoor pipe temp.
• While in defrost control, both of the indoor and outdoor fans are turned off.
■ Defrost Control
• While in heating mode operation in order to protect the evaporator pipe of the outdoor unit from freezing,
reversed to cooling cycle to defrost the evaporator pipe of the outdoor unit.
• After 40 min heating mode operation, at 4 min interval, whether to carry out defrost control or not and the time
of defrost control are determined according to the following conditions.
1) While in heating mode operation, the maximum of the indoor pipe temperature is measured and it is com-
pared with the present indoor pipe temperature to get the difference of the indoor pipe temperatures (=the
maximum temperature of indoor pipe ? the present temperature of indoor pipe), according to which, whether
to carry out defrost control or not is determined.
2) According to the need of defrost control shown above and the elapsed time of heating mode operation at that
moment, the defrost control time is determined.
3) When the determined time of defrost control is below 7 min, heating mode operation continues without carry-
ing out defrost control. According to the procedure stated above, the determination is made again. When the
defrost control time is 7 min or longer, defrost control is then carried out.
• While in defrost control, the minimum temp of the indoor pipe is measured and it is compared with the present
temp of the indoor pipe to get the difference of the indoor pipe temperatures (=the present temperature of the
indoor pipe ? the minimum temperature of the indoor pipe). When the difference is 5°C or higher, defrost con-
trol is completed and heating mode operation is carried out.
• While in defrost control, if the defrost time determined before the start of defrost control is completed, defrost
control stops and heating mode operation is carried out regardless of the above condition.
• When the indoor pipe temp is 42°C or above, defrost control is not carried out even if the condition is one of
the defrost conditions above.
• While in defrost control, the compressor is on and the indoor fan, the outdoor fan, and the 4 way valve are off.

Operation
■ Airflow Speed Selection

• The airflow speed of the indoor fan is set to high, medium, low, or chaos (auto) by the input of the airflow
speed selection key on the remote control.
■ Sleep Timer Operation

• When the sleep time is reached after <1,2,3,4,5,6,7,0(cancel) hr> is input by the remote control while in appli-
ance operation, the operation of the appliance stops.
• While the appliance is on pause, the sleep timer mode cannot be input.
• While in cooling mode operation, 30 min later since the start of the sleep timer, the setting temperature
increases by 1°C. After another 30 min elapse, it increases by 1°C again.
• When the sleep timer mode is input while in cooling cycle mode, the airflow speed of the indoor fan is set to
the low.
• When the sleep timer mode is input while in heating cycle mode, the airflow speed of the indoor fan is set to
the medium.
■ Chaos Natural Wind Mode

• When the Chaos Natural Wind mode is selected and then operated, the high, medium, or low speed of the air-
flow mode is operated for 2~15 sec. randomly by the Chaos Simulation.
■ Jet Cool Mode Operation (C/O Model)

• If the Jet Cool key is input at any operation mode while in appliance operation, the Jet Cool mode operates.
• In the Jet Cool mode, the indoor fan is operated at super-high speed for 30 min at cooling mode operation.
• In the Jet Cool mode operation, the room temperature is controlled to the setting temperature, 18°C
• When the sleep timer mode is input while in the Jet Cool mode operation, the Jet Cool mode has the priority.
• When the Jet Cool key is input, the upper/lower vanes are reset to those of the initial cooling mode and then
operated in order that the air outflow could reach further.
■ Jet Cool Mode Operation (H/P Model)

• While in heating mode or Fuzzy operation, the Jet Cool key cannot be input. When it is input while in the
other mode operation (cooling, dehumidification, ventilation), the Jet Cool mode is operated.
• In the Jet Cool mode, the indoor fan is operated at super-high speed for 30 min at cooling mode operation.
• In the Jet Cool mode operation, the room temperature is controlled to the setting temperature, 18°C.
• When the sleep timer mode is input while in the Jet Cool mode operation, the Jet Cool mode has the priority.
• When the Jet Cool key is input, the upper/lower vanes are reset to those of the initial cooling mode and then
operated in order that the air outflow could reach further.
■ Forced Operation
• Operation procedures when the remote control can't be used.
• The operation will be started if the power button is pressed.
• If you want to stop operation, re-press the button.
Heat pump Model
Cooling Model
Room Temp. ≥ 24°C 21°C ≤ Room Temp. < 24°C Room Temp. < 21°C
Operating mode Cooling Cooling Healthy Dehumidification Heating
Indoor FAN Speed High High High High
Setting Temperature 22°C 22°C 23°C 24°C
• While in forced operation, the key input by the remote control has no effect and the buzzer sounds 10 times to
indicate the forced operation.
Service Manual 31

Operation
■ Test operation
• During the TEST OPERATION, the unit operates in cooling mode at high speed fan, regardless of room tem-
perature and resets in 18±1 minutes.
• During test operation, if remote controller signal is received, the unit operates as remote controller sets.
If you want to use this operation, open the front panel upward and Press the power button let it be pressed for
about 3 seconds.
• If you want to stop the operation, re-press the button.
■ Auto restart
• In case the power comes on again after a power failure, Auto Restarting Operation is the function to operate
procedures automatically to the previous operating conditions.
■ Protection of the evaporator pipe from frosting

• If the indoor pipe temp is below 0°C in 7 min. after the compressor operates without any pause while in cool-
ing cycle operation mode, the compressor and the outdoor fan are turned off in order to protect the indoor
evaporator pipe from frosting.
• When the indoor pipe temp is 7°C or higher after 3 min. pause of the compressor, the compressor and the
outdoor fan is turned on according to the condition of the room temperature.
■ Buzzer Sounding Operation

• When the appliance-operation key is input by the remote control, the short "beep-beep-" sounds.
• When the appliance-pause key is input by the remote control, the long "beep—" sounds.
• When a key is input by the remote control while the slide switch on the main unit of the appliance is on the
forced operation position, the error sound "beep-beep-beep-beep-beep-" is made 10 times to indicate that the
remote control signal cannot be received.

Operation
Display Function
1. Heating Model 2. Cooling Model
Operation Indicator Operation Indicator
• Cooling, Soft Dry, Fan, Heating • Cooling, Soft Dry, Fan
Compressor on Indicator OUT

Deicer Indicator DOOR
• Hot-start, Deice
Self-diagnosis Function
Error Error Display LED
Error contents SVC check point
Code (Indoor body operation LED)
• Indoor room temperature
(once) thermistor open/short • Indoor Thermistor
1
• Indoor pipe temperature assembly check
3sec 3sec 3sec thermistor open/short.
Service Manual 33

Operation
Remote Control Operations

The remote control transmits the signals to the system.

Disassembly
Disassembly
Indoor Unit
Disconnect the unit from power supply before mak-

ing any checks.
Be sure the power switch is set to “OFF”.
To remove the Grille from the Chassis.

• Set the up-and-down air discharge louver to open
position (horizontally) by finger pressure.
• Remove the securing screws.
• To remove the Grille, pull the lower left and right
side of the grille toward you (slightly tilted) and lift it
straight upward.
1. Before removing the control box, be sure to

take out the wire screwed at the other end.
Earth
Conductor
Service Manual 35

Disassembly
2. To remove the Control Box.

• Remove securing screws. Caution label
• Pull the control box out from the chassis
carefully.
3. To remove the Discharge Grille.

• Unhook the discharge grille and pull the
discharge grille out from the chassis carefully.
4. To remove the Evaporator.

• Remove 3 screws securing the evaporator(at the
left 2EA in the Eva Holder, at the right 1EA).
• When repair, do not damage the Caution label.

Disassembly
• Unhook the tab on the right inside of the chassis

at the same time, slightly pull the evaporator
toward you until the tab is clear of the slot.
5. To remove the Motor Cover

• Remove 2 securing screw.
• Pull the motor cover out from the chassis
carefully.
Motor cover
6. To remove the Cross-Flow Fan

• Loosen the screw securing the cross-flow fan to
the fan motor (do not remove).
• Lift up the right side of the cross-flow fan and the
fan motor, separate the fan motor from the
cross-flow fan.
• Remove the left end of the cross-flow fan from

the self-aligning bearing.
Service Manual 37

C01p
12V
DC PART 103
D01M
1N4148 RY-4WAY
1 8
G Vcc 5V
2
7 R01P R02P Q01M
A2 WP 20K 20K R1
CN-TH1 (SRC1201S)
3 6
A1 SCL R1,R2=4.7K
SMAW-200 4 5 R2
A0 SDA
R03D C09D
ROOM-TH 4 4 EEPROM 100 1 16
103
CAT24WC01J 5V RY-FAN
3 3 A
V
R 2 15
2 2 RY-COMP
PIPE-TH E
1 1 F
3 14 CN-U/D
INDOOR FAN STEPPING MOTOR
CN-OPTION 5V 44 43 42 41 40 39 38 37 36 35 34 SMAW-200 (UP/DOWN)
OPTION SMW-200 R02H
12.1K
R04H
6.2K
R01H
10K ROOM TH A BL
4 13
R21H-26H
C01H
1 ANI0 V
D
33 1 1
F1,OR1H 1 1 1 1 12.1K,1% 103
R03H PIPE D PK
5V R05H
10K
10K
C02HJ 2 ANI1 32 5 12
2 2
F2,OR2H 2 2 2 2 103
R21H OPTION1 6 11 YL
3 ANI2 31 3 3
F3,OR3H 3 3 3 3
R22H OPTION2 7 10 OR
4 ANI3 30 4 3
LOW,OR4H 4 4 4 4
RD
R23H OPTION3 8 9
5 5
MIDDLE,OR5H 5 5 5 5
5 ANI4
uPD78F9166GB VDD0 29 5V
12V
C07D
R24H LOW 103
6 ANI5 28
HIGH,OR6H 6 6 6 6
R25H MIDDLE
NEC(16K) VSS0
7 7 7 7 7 ANI6 / LED1 X1 27
R01B
R26H HIGH 1M
8 ANI7 / LED2 X2 26 R02A
4.7K
OSC01B R01A 5V
CRTL4.00MSOT 1K 1
9 25
3
RESET +
3.6V
C01A C02A R03A 2
103 IC01A
DISPLAY CN-DISP1 OPERATION
10uF/50V 100
KIA7036P
R13L SMAW-200
OR1H-6H
5%
10 I I
24 S7136
100,1/4W 5V TIMER N N V T R V
OR1HOR2H OR3H OR4H OR5H OR6H
Vcc
8 8 11 T
0
T
1
B
Z
D
D
X
D
X
D
P
P
23
GND R12L
R11L C11L
Vout 1K,1/6W 680pF/50V REALY CONNECTION
RECEIVER
7 7
5.1K,1/8W
12 13 14 15 16 17 18 19 20 21 22
C13L Q04G FAN-IN FAN-OUT C08D
CN-CENT
Schematic Diagram
104 6 6 6 6 103
R1
SMAW-200
12V L(AC)
R2 Q03G
3
5 5 5 5 5 5
LED2
4
OUTDOOR COMP LOAD
Q02G
4 4 4 4 COMP
R02G 4 4
LED1 4WAY
4WAY
OPERATION 220,1/4W FORCE C03T
3 3 3 3 Q01G 5V 10K,1/6W FAN FAN
• Heat Pump Model(LED TYPE)
R01G GND 3 3
220,1/4W
C14L
5V
R14L R15L
2 2 2 2 5V Q01G~04G 103 1K 20K
C12L (SRC1201S) R02E
20
5V 2 2
220/10V R1,R2=4.7K
1 1 1 1 FORCE R01E BZ01E
1K PKM13EPY-4002 12V 1 1
SW(FORCE)
Electric Control Device
INDOOR
R04L
5V CN-MOTOR FAN MOTOR
C01L 12K
AC PART 103 Q01L
R05L
INT 3 3
KTC3198-Y
2SC5343 56K R01F R02F 2 2
560,1/4W 680,1/2W SH-CAPACITOR
1
12V 5 1 1
2
3
4 R04F
T2
120,1/2W

C06J INDOOR FAN TR01F
IC01F
102,1KV SM1L43
C01F
IL440-2 T1
100nM/275V/436D
EE1916S IC01J D01J
L02D ICO1A L01D C04J D05J
Lp=3.44mH LINKSWITCH 1N4007 D04J R03F ZNR01F OUTDOOR FAN
CHIP S78DL05L 12V BEAD 1uF,50V LNK500P NTC SCK-102 1N4007 CN-4WAY
MOTOR
O I SMPS S D 1N4007 100,1/2W TVR10561

5V 7805 3 4
8 3 C
D02J RY-FAN 3 3 5 5
+
5V D03J NF01J 3
1N4007 4
R01J R03L,1% R01L 1N4007 40mH/1A RY-4WAY 2 2 4 4
C03D C05J 27K,1/4W 300K,1/2W 4WAY
+ + R01D + 27K,1/4W 1 1 3 3
C05D C04D 103/25V C02D 4.7K,1/6W C01D 0.1uF,100V +
C03J FUSE
INT ZNR01J CN-N2
220/10 103/25V 100/25V 220,25V 6.8/450 250V/T2A 2 2
D06J 4 1 TVR10561 1 1 2N
D01D 1N4937 IC01L D01L 4 1 1
R02L RY-COMP
UF4004 TCET1109-3208 2 1N4148 C02J C01J 3 1(L) COMPRESSOR
5 R02J 3 300K,1/2W G4A-1A-E-LG
1
47nM/275V/435D 100nM/275V,436D MOTOR
100,1/8W
DC LOW C06D R01P
VOLTAGE GND 102,1KV R02D DC LOW DC HIGH
1 1
4.7K,1/6W VOLTAGE GND VOLTAGE GND CN-N1 R01P
AC220-240V
Schematic Diagram
50/60HZ
Schematic Diagram
Wiring Diagram
Indoor Unit
Models: AS-H0766KA2, AS-H0966KA2, Models: LS-C126RKA2
AS-H126RKA2, LS-H0766KA2, LS-C0966KA2
LS-H0966KA2, LS-H126RKA2
AS-H186TKA2, AS-H246TKA2
Outdoor Unit
Models: LS-H0766KA2, Models: LS-C126RKA2 Models: AS-H246TKA2
LS-H0966KA2, LS-C0966KA2
AS-H126RKA2,
LS-H0766KA2,
LS-H0966KA2,
LS-H126RKA2
AS-H186TKA2
Service Manual 39

Schematic Diagram
Components Location
MAIN P.W.B ASSEMBLY
• TOP VIEW
2004/06/19 DIP
250V/T2A CN-DISP1
CN-U/D
FUSE
J8
RY-COMP CN-TH1
D01M
C02H
CN-OPTION
4 C12L
3 CN-4WAY J2
CN-N1
C01H
CN-N2
CN-CENT
J4
C01P
NF01J
J5
J01
J15
C09D J10
CN-MOTOR
J6
R03D
J9
C01J
R04F ZNR01J C07D
C02J
J7
C01F
RY-4WAY RY-FAN R11L
IC01L C11L
ZNR01F
R01L
OSC01B
D02J
R03L
C08D
D01J
C01A
D03J
R02J D01L
C03T
R01A
C01D
D04J
R02F
R02L C06J BZ01E

D06J
C14L C01L
R03F
TR01F IC01A
D05J
L01D
J11
NTC
J12
4 1
R04L
C04D
C05J
J14
C02A R14L
IC01J
R01J
Q01L
IC01F
J13
D01D
R01F
5 8 C02D IC01D
C05D
C03D
R02D C06D
C04J SMPS
C03J
PWB: 6870A90239A PWB ASM: 6871A20573
• BOTTOM VIEW
CN-TH1
CN-DISP1 CN-U/D FUSE
J8
R02H
R04H
R01H
C12L
OR6H R03H R05H
R12L
RY-COMP
R15L
CN-OPTION
D01M
OR5H
OR1H
OR4H
OR2H
OR3H
R21H
J26
C02H
J2 CN-4WAY
CN-N1
C01H
R02P
R01P
Q01M
CN-N2
CN-CENT
J4
C01P
R26H
R23H
R22H
R24H
R25H
NF01J
J5
J01 EEPROM
J15 IC01M
J16 C09D
CN-MOTOR
J6
J21 J20
Q01G
1 R03D
MICOM
J9
J22 C01J
ZNR01J R04F
Q02G 43 C07D C02J
J7
C01F
R11L RY-FAN RY-4WAY
C11L IC01L
Q03G 21 ZNR01F
R05L
R01L
OSC01B
J23 J24
D02J
R01B
R01E
R02E
R03L
32
D01J
C08D
C01A
D03J
D01L R02J
R02A
BZ01E J25
J17 R03A
C03T
R01A
D04J
C14L
R02F
C01D
C06J
D06J
R02L
J19 J18 Q04G
R01D
R03F
D05J
IC01A TR01F
L01D
C01L J16
J11
NTC
J12
R04L
C04D
C05J
J14
R14L C02A
IC01J
IC01F
R01J
Q01L
J13
D01D
R01F
IC01D C02D
L02D
C05D
C03D
C06D R02D
SMPS C04J C03J

– 6871A20575
2004/06/19 DIP
250V/T2A CN-DISP1
CN-U/D
FUSE
J8
RY-COMP
DISPLAY ASSEMBLY
CN-TH1
C02H
D01M
C12L

3 4 CN-4WAY J2
CN-N1
CN-OPTION
C01H
CN-N2
J4
NF01J
C01P
J5
CN-CENT
J01
J15
C09D J10
J6
R03D
CN-MOTOR
J9
C01J
R04F ZNR01J C07D
C02J
C01F J7
RY-4WAY RY-FAN R11L
IC01L C11L
ZNR01F
R01L
D02J
R03L
OSC01B
C08D
C01A
D01J
R02J D01L
D03J
C03T
C01D
R01A
R02L C06J BZ01E
D04J
C14L
R02F
C01L
D06J
TR01F IC01A
D05J
R03F
L01D
NTC
J11
4 1
J12
C04D
R04L
C02A R14L
J14
C05J
IC01J
Q01L
R01J
J13
IC01F
IC01D
D01D
5 8 C02D
R01F
C03D
C05D
R02D C06D
C04J SMPS
C03J
PWB: 6870A90239A PWB ASM: 6871A20573
Service Manual 41
Schematic Diagram
Troubleshooting Guide
Refrigeration Cycle Diagram
(1) Cooling Only Models
INDOOR UNIT OUTDOOR UNIT
LIQUID SIDE
CAPILLARY TUBE
HEAT HEAT
EXCHANGE EXCHANGE
(EVAPORATOR) (CONDENSER)
GAS SIDE
COMPRESSOR
(2) Cooling & Heating Models
INDOOR UNIT OUTDOOR UNIT
CHECK VALVE
LIQUID SIDE (Heating Model only)
3-WAY VALVE
CAPILLARY TUBE
HEAT HEAT
EXCHANGE EXCHANGE
(EVAPORATOR) (CONDENSER)
GAS SIDE
REVERSING
3-WAY VALVE
ACCUMU VALVE
LATOR (Heating Model Only)
COMPRESSOR COOLING
HEATING

2-way, 3-way Valve

2-way Valve (Liquid Side) 3-way Valve (Gas Side)
Valve cap
Hexagonal wrench (4mm) Open position
Flare nut Flare nut Closed position
Open position
Closed position Pin
To To
piping piping Service Service
connection connection port cap port
To outdoor unit To outdoor unit
Works Shaft position Shaft position Service port
Closed Closed Closed

Shipping
(with valve cap) (with valve cap) (with cap)
Air purging Open Closed Open

1. (Installation) (counter-clockwise) (clockwise) (push-pin or with
vacumm pump)
Open Open Closed

Operation
(with valve cap) (with valve cap) (with cap)
Pumping down Closed Open Open

2. (Transfering) (clockwise) (counter-clockwise) (connected manifold
gauge)
Evacuation Open Open Open

3. (Servicing) (with charging
cylinder)
Gas charging Open Open Open

4. (Servicing) (with charging
cylinder)
Pressure check Open
5. (Servicing) Open Open (with charging cylinder)
Gas releasing Open

6. Open Open (with charging cylinder)
(Servicing)
Service Manual 43

Pumping Down
Indoor unit Liquid side

Open Outdoor unit
2-Way
valve
Gas side
Closed
3-Way
valve
Lo
CLOSE CLOSE
Purge the air
• Procedure
(1) Confirm that both the 2-way and 3-way valves (6) Operate the air conditioner at the cooling
are set to the open position. cycle and stop it when the gauge indicates
– Remove the valve stem caps and confirm that 1kg/cm2g.
the valve stems are in the raised position.
– Be sure to use a hexagonal wrench to operate (7) Immediately set the 3-way valve to the closed
the valve stems. position.
– Do this quickly so that the gauge ends up indi-
(2) Operate the unit for 10 to 15 minutes. cating 3 to 5kg/cm2g.
(3) Stop operation and wait for 3 minutes, then (8) Disconnect the charge set, and mount the 2-
connect the charge set to the service port of way and 3-way valve’s stem nuts and the ser-
the 3-way valve. vice port nut.
– Connect the charge hose with the push pin to – Use torque wrench to tighten the service port
the service port. nut to a torque of 1.8 kg.m.
– Be sure to check for gas leakage.
(4) Air purging of the charge hose.
– Open the low-pressure valve on the charge set
slightly to air purge from the charge hose. Do not use the existing charge set for R-22.
It is necessary to use new charge set for R-410A.
(5) Set the 2-way valve to the closed position. The pressure of R-410A is 1.6 times higher than
that of R-22. Thus, the high pressure side gauge of
charge set should be used higher pressure gauge
of 50kg/cm2 range.

Balance Refrigerant of the 3-way Valve

(Gas leakage)

Outdoor unit
3-Way
valve Open
Gas side
3-Way
valve Open
Lo
OPEN CLOSE
• Procedure
(1) Confirm that both the 2-way and 3-way valves (3) Open the valve (Lo side) on the charge set and
are set to the back seat. discharge the refrigerant until the gauge indi-
cates 0 kg/cm2G.
(2) Connect the charge set to the 3-way valve’s – If there is no air in the refrigerant cycle (the
port. pressure when the air conditioner is not running
– Leave the valve on the charge set closed. is higher than 1 kg/cm2G), discharge the refrig-
– Connect the charge hose to the service port. erant until the gauge indicates 0.5 to 1
kg/cm2G. if this is the case, it will not be neces-
sary to apply a evacuatin.
– Discharge the refrigerant gradually; if it is dis-
charged too suddenly, the refrigeration oil will
also be discharged.
Service Manual 45

Evacuation
(All amount of refrigerant leaked)

Outdoor unit
3-Way
valve Open
Gas side
3-Way
valve Open
Vacuum pump
Lo
OPEN CLOSE
• Procedure
(1) Connect the vacuum pump to the center hose (3) Close the valve (Lo side) on the charge set,
of charge set center hose turn off the vacuum pump, and confirm that
the gauge needle does not move (approxima-
(2) Evacuation for approximately one hour. tely 5 minutes after turning off the vacuum
– Confirm that the gauge needle has moved pump).
toward -76 cmHg (vacuum of 4 mmHg or less).
(4) Disconnect the charge hose from the vacuum
pump.
– Vacuum pump oil.
If the vacuum pump oil becomes dirty or
depleted, replenish as needed.
Use vacuum pump equipped with check value

applied to be prevented from flowing backward.

Gas Charging
(After Evacuation)

Open Outdoor unit
3-Way
valve
Gas side
Open
3-Way
Check valve valve
Charging
cylinder
Lo
(1) OPEN CLOSE
• Procedure
\
(1) Connect the charge hose to the charging

This is different from previous procedures.
cylinder.
Because you are charging with liquid refrigerant
– Connect the charge hose which you dis-con-
from the gas side, absolutely do not attempt to
nected from the vacuum pump to the valve at
charge with larger amounts of liquid refrigerant
the bottom of the cylinder.
while operating the air conditioner.
– If you are using a gas cylinder, also use a
scale and reverse the cylinder so that the sys- (4) Immediately disconnect the charge hose from
tem can be charged with liquid. the 3-way valve’s service port.
(2) Purge the air from the charge hose. – Stopping partway will allow the gas to be dis-
– Open the valve at the bottom of the cylinder charged.
and press the check valve on the charge set to – If the system has been charged with liquid
purge the air. (Be careful of the liquid refriger- refrigerant while operating the air conditioner
ant). The procedure is the same if using a gas turn off the air conditioner before disconnecting
cylinder. the hose.
(3) Open the valve (Lo side on the charge set and (5) Mount the valve stem nuts and the service
charge the system with liquid refrigerant. port nut.
– If the system can not be charged with the spec- – Use torque wrench to tighten the service port
ified amount of refrigerant, it can be charged nut to a torque of 1.8 kg.m.
with a little at a time (approximately 150g each – Be sure to check for gas leakage.
time) while operating the air conditioner in the
cooling cycle; however, one time is not suffi-
cient, wait approximately 1 minute and then
This unit is charged with R-410A.
repeat the procedure (pumping down-pin).
Pay attention not to charge R-22.
Service Manual 47

Additional gas charging

(Gas leakage)
• When refrigerant is insufficient by leakage, recharge the unit with the refrigerant up to normal operating suc-
tion pressure.
• Use the graph or the equation below to get operating suction pressure according to indoor and outdoor tem-
perature.
Suction pressure was measured at 3-way valve service port after operating the unit for 10 minutes.
The method of using graph

- Find outdoor temperature.
- Find indoor temperature onto the curve of outdoor temperature.
- Read suction pressure at the axis of ordinates.
The method of using equation
-. Calculate suction pressure after putting indoor and outdoor temperature into the equation.
Operating Suction Pressure

(According to Indoor & Outdoor Temperature)
(At operating the Unit for 10 minutes)

13
50˚C
12
11 40˚C
Suction Pressure
Outdoor Temp.
(Kg/cm2.g)
10 30˚C
(˚C)
9 20˚C
10˚C
8
0˚C
7
5
5 10 15 20 25 30 35 40
Indoor Temp. (˚C)
P = 3 + 0.0123 x Tout1.5 + 0.8 x Tin0.5

2
Where, P : Suction Pressure(kg/cm .g)
Tout : Outdoor Temperature(˚C)
Tin : Indoor Temperature(˚C)

Cycle Parts
Trouble analysis
1. Check temperature difference between intake and discharge air and operating current.
Temp. difference : approx. 0°C

• All amount of refrigerant leaked
Current : less than 80% of
out. Check refrigeration cycle.
rated current
Temp. Difference • Refrigerant leakege

Temp. difference : approx. 8°C
Current : less than 80% of Clog of refrigeration cycle
rated current Defective compressor
Operating Current Temp. difference : less than 8°C

Current : over the reated • Excessive amount of refrigerant
current
Temp. difference : over 8°C • Normal
NOTICE
Temperature difference between intake and discharge air depends on room air humidity. When the room air
humidity is relativery higher, temperature difference is smaller. When the room air humidity is relatively lower
temperature difference is larger.
2. Check temperature and pressure of refrigeration cycle.
Suction pressure Temperature

(Compared with (Compared with Cause of Trouble Description
the normal value) the normal valve)
Defective compressor Current is low.

High
Defective 4-way reverse valve
Higher
Excessive amount of High pressure does not quickly
Normal refrigerant rise at the beginning of
operation.
Insufficient amount of Current is low.

Lower Higher refrigerant (Leakage)
Clogging Current is low.
NOTICE
1. The suction pressure is usually 8.5~9.5 kg/cm2G(Cooling) at normal condition.
2. The temperature can be measured by attaching the thermometer to the low pressure tubing and wrap it with
putty.
Service Manual 49

Electronic Parts
Product does not operate at all.
(* Refer to Electronic Control Device drawing and Schematic diagram.)
Turn off Main Power
(After 10 seconds)
Turn on Main Power
Does "beeping" sound is made from the Indoor Unit?
NO YES
Check the voltage of power(About AC 220V, 60Hz) Primarily, the operating condition of Micom is OK.
(About AC 220/240V, 50Hz)
• Main power's voltage

• Voltage applied to the unit
• Connecting method of Indoor/Outdoor connecting
cable Check each load(Indoor/Outdoor Fan Motor,
• Check PWB Assembly Compressor, Stepping Motor) and contacting
- Fuse condition of related connector
- Pattern damage
- Varistor(ZNR01J)
Check the connection housing for contacting
• Connector related to CN-TAB1, RY-COMP NO.3

• Connector related to CN-MOTOR
• Connector contacting of Outdoor Fan/Compressor
• Display PCB Assembly Check
Main PCB Board Operation Check

Items Content Remedy
• SMPS Transformer
(Indoor unit)
- Input Voltage - About AC220V/240V±10% - Check the power voltage • Replace Trans
- Output Voltage(ZD02D) - About DC12V
• IC04D(7805) Output • DC +5V • Replace IC04D

(Indoor/Outdoor unit)
• IC01A(KIA7036, Reset IC) • Voltage of Micom No. 2, • Replace faulty parts

X01(8MHz) (DC +4.5V over) and Soldering condition.

The product is not operate with the remote controller.
Turn on Main Power
While the compressor has been stopped, the compressor does not
operate owing to the delaying function for 3 minutes after stopped.
When the compressor stopped Indoor Fan is driven by a low speed.

At this point the wind speed is not controlled by the remote controller.
(When operated in the Sleeping Mode, the wind speed is set to the
low speed by force.)
Cause by the remote control Caused by other parts except the remote control
When the mark( ) is displayed in LCD screen, replace

Check the contact of CN-DISP1 connector.
battery.
Check the connecting circuit between the remote controller

Check Display PCB Assembly
MICOM (No. ) - R17(2Ω) - IR LED - TR - R16(2.2KΩ).
- Voltage between CN DISP1 - : DC +5V
Check point
• Check the connecting circuit between CN-DIS1 -

R01L(5.1kΩ) - C01L(680pF) - MICOM PIN
• Check Receiver Assembly
Service Manual 51

Compressor/Outdoor Fan are unable to drive.
Turn on Main Power
Operate "Cooling Mode( )" by setting the desired temperature of the

remote controller is less than one of the indoor temperature by 1°C at least.
When in Air Circulation Mode, Compressor/Outdoor Fan is stopped.
Check the sensor for indoor temperature is attached as close as to be

effected by the temperature of Heat Exchanger(EVA).
When the sensor circuit for indoor temperature and connector are in bad
connection or are not engaged, Compressor/Outdoor Fan is stopped.
• Check the related circuit of RY-FAN.

• Check the indoor temperature sensor is disconnected or not(About 10kΩ / at 25°C).
Check Relay(RY - COMP) for driving compressor.
• When the power(About AC220V/240V) is applied to the connecting wire

terminal support transferred to compressor, PWB Assembly is normal.
• Check the circuit related to the relay.
Check point COMP ON COMP OFF
Between Micom(No.
DC5V DC0V
62) and GND
Between IC01M(No. 14) Below DC 1V
About DC12V
and GND (app)
Turn off Main Power
• Check the electrical wiring diagram of outdoor side.

• Check the abnormal condition for the component of
Compressor/Outdoor Fan Motor.
• Check the "open" or "short" of conmecting wires between indoor and
outdoor.

When indoor Fan does not operate.
Turn off Main power
Check the connection of CN-MOTOR
Check the Fan Motor
Check the Fuse(AC250V/T2A)
Check the related circuit of indoor Fan Motor.
• The pin NO 63 of Micom, and the part for driving TRIAC(the input and
output signal of IC01M, PIN NO 7, 10)
• Check the pattern
• Check the TRIAC
- TRIAC Open: Indoor Fan Motor never operate
- TRIAC short: Indoor Fan Motor always operates in case of ON or OFF.
Turn ON Main Power
Check the TRIAC high speed operation by remote control.

(The Indoor Fan Motor is connected)
The voltage of PIN NO 1(orange) and 3(yellow) of CN-MOTOR.
About AC 180V over About AC 50V over
TRIAC is not damaged TRIAC Check
Service Manual 53

When Vertical Louver does not operate.
• Confirm that the Vertical Louver is normally geared with the shaft of
Stepping Motor.
• If the regular torque is detected when rotating the Vertical Louver with
hands Normal
• Check the connecting condition of CN-U/D Connector

• Check the soldering condition(on PWB) of CN-U/D Connector
Check the operating circuit of the Vertical Louver
• Confirm that there is DC +12V between pin (RED) of CN-U/D and

GND.
• Confirm that there is a soldering short at following terminals.
- Between 60 , 61 , 62 and 63 of MICOM
- Between , , and of IC01M
- Between , , and of IC01M
If there are no problems after above checks
• Confirm the assembly conditions that are catching and interfering parts
in the rotation radial of the Vertical Louver

When Heating does not operate
Turn ON Main Power
Operate “Heating Mode( )” by setting the desired temperature of the

remote control is higher than one of the indoor temperature by 2°C at
least.
In heating Mode, the indoor fan operates in case the pipe temperature
is higher than 28°C.
Check the connector of intake and pipe sensor(thermistors)
• Check the related circuit of RY-4WAY

• Check the indoor room temperature is disconnected or not (about
10KΩ/at 25°C).
• Check the indoor pipe temperature is disconnected or not (about
5KΩ/at 25°C).
Check the DC voltage on the PWB ASSEMBLY
• The details of check are as followings

• Comp Relay. • Outdoor fan Relay
Check point Comp ON Comp OFF Check point Fan ON Fan OFF
Between Micom Between Micom

DC 5V DC 0V DC 5V DC 0V
(NO.59) and GND (NO.53) and GND
Between IC01M Between IC02M

Below DC 1V About DC Below DC 1V About DC 12V
(NO.11) and GND (NO.12) and GND
12V
• 4 way Relay
Check point 4 way ON 4 way OFF
Between Micom
DC 5V DC 0V
(NO.51) and GND
Between IC02M
Below DC 1V About DC 12V
(NO.11) and GND
Service Manual 55

Turn off Main Power
• Check the electrical wiring diagram of outdoor side.

• Check the abnormal condition for the component of
Compressor/Outdoor Fan Motor, 4 way.
• Check the "open" or "short" of connecting wires between indoor and
outdoor.

Exploded View
Exploded View
Indoor Unit
135316
135313
152302
131410 733010
359011
342800
354210
147581
268711 268712
35211B 346810
W0CZZ 135516
135311 352150
146811
267110
249951
Service Manual 57

Exploded View
135316
Option Parts
152313
135314
152302
131410 733010
359011
267110
342800
159830 Part for

Plasma Models
135311 354210
159901-1
159901-2 35211B
Part for 145201
Plasma Models
268712 249951
266090 346810
135516
268714-1 268714-2
352150
668713
145200 146811
264110
264110 266090
Part for Plasma
268714 Models
263230 263230
W6640 W0CZZ-1

Exploded View
Outdoor Unit: 7,9,18K Btu/h Models
437211
349480
437212
554031
435301
435511
546810
559010
649950
552111
552116
552202
Part for
H/P Models
567502
Part for
External Models 561410
554160
447900
550140 552203-1
430411
552203-2
Service Manual 59

Exploded View
Outdoor Unit: 12k Btu/h Models
437211
435301
237204-2
435300
237204-1
435511
554031
546810
552111
559010
567502 Part for

External Models
WOCZZ-2
554160
447910
552202 649950
550140 552203-1
561410
552116
Part for 430410

H/P Models 552203-2

Exploded View
Outdoor Unit
554032
437212
435512
552111
649950
W0CZZ-1
435511
559010
W0CZZ-2
668713
546810
552202 552116
Part for
H/P Models
553000
567502
435301 447910 Part for
External Models
554160
552203-2
550140
430410
437210 552203-1
Service Manual 61

Replacement Parts List

Parts List (Indoor)
LOCATION PART No.
DESCRIPTION REMARKS
No. AS-H0766KA2 AS-H0966KA2 AS-H126RKA2 AS-H186TKA2 AS-H246TKA2
131410 CHASSIS ASSEMBLY 3141A20017A 3141A20017A 3141A20024A 3141A20028A 3141A20028A R
267110 REMOTE CONTROLLER ASSEMBLY 6711A90023C 6711A90023C 6711A90023C 6711A90023C 6711A90023C R
346810 MOTOR ASSEMBLY,INDOOR 4681A20151A 4681A20151A 4681A20048A 4681A20003D 4681A20067A R
135516 COVER ASSEMBLY,MOTOR 3551A30135A 3551A30135A 3551A20169A 3551A20050D 3551A20050K R
359011 FAN ASSEMBLY,CROSS FLOW 5901A20035A 5901A20035A 5901A20037A 5901A20008A 5901A20008A R
342800 BEARING 4280A20004B 4280A20004B 4280A20004B 4280A20004A 4280A20004A R
354210 EVAPORATOR ASSEMBLY,FIRST 5421A10052A 5421A10052A 5421A20086A 5421A20010D 5421A20010D R
35211B TUBE ASSEMBLY,TUBING 5211A21046X 5211A21046X 5211A21046Y 5211A30038Z 5211AR7066T R
249951 CONTROL BOX ASSEMBLY,INDOOR 4995A20435A 4995A90435A 4995A20435A 4995A20435C 4995A20435E R
263230 THERMISTOR ASSEMBLY 6323A20004A 6323A20004A 6323A20004A 6323A20004A 6323A20004A R
268714-1 PWB(PCB) ASSEMBLY,MAIN 6871A20573A 6871A20573A 6871A20573A 6871A20272K 6871A20573C R
264110 POWER CORD ASSEMBLY 6411A20013E 6411A20013E 6411A20013E 6411A20047A 6411A20047B R
668713 PWB(PCB) ASSEMBLY,SUB 6871A20631A 6871A20631B 6871A20631T 6871A20631G 6871A20631J R
W0CZZ CAPACITOR,DRAWING 3H01487K 3H01487K 3H01487K 3H01487G 3H01487G R
135311 GRILLE ASSEMBLY,DISCHARGE(INDOOR) 3531A10301A 3531A10301A 3531A10314A 3531A10325A 3531A10325A R
146811 MOTOR ASSEMBLY,STEP 4681A20055A 4681A20055A 4681A20055A 4681A20055A 4681A20055A R
268712 PWB(PCB) ASSEMBLY,DISPLAY 6871A20575A 6871A20575A 6871A20575A 6871A20573C 6871A20575A R
159901 VANE,HORIZONTAL 5990A20046A 5990A20046A 5990A20007A 5990A20008A 5990A20008A R
352150 DRAIN ASSEMBLY,TUBE 5251A20011B 5251A20011B 5251A20011B 5251A20011D 5251A20011D R
733010 PLATE ASSEMBLY,INSTALL 3301A10003A 3301A10003A 1H00843A 3301A10002A 3301A10002A R
135312 GRILLE ASSEMBLY,FRONT(INDOOR) 3531A20249A 3531A20249A 3531A10315B 3531A20272D 3531A20272D R
135314 GRILLE,INLET 3530A00062A 3530A00062A 3530A10090B 3530A00087A 3530A00087A R
152302 FILTER(MECH),A/C 5230A20049A 5230A20049A 5230A20014C 5230A20001D 5230A20001D R
435512 COVER ASSEMBLY, TOP(OUTDOOR) 3H03266K 3H03266K 3H03266K 3H03266K 3H03266K R
NOTE) *Please ensure GCSC since these parts may be changed depending upon the buyer's request.
(GCSC WEBSITE http://biz.LGservice.com)

Parts List (Indoor)

LOCATION PART No.
DESCRIPTION REMARKS
No. LS-H0766KA2 LS-H0966KA2 LS-H126RKA2 LS-C126RKA2 LS-C0966KA2
430410 BASE ASSEMBLY,OUTDOOR 3041A20079A 3041A20079A 3041A20072D 3041A20072B 3041A20079A R
552203-1 VALVE,SERVICE 2H02479P 2H02479P 5220A20005B 5220A20005B 2H02479P R
552203-2 VALVE,SERVICE 5220A20040A 5220A20040A 2H01890P 2H01890P 5220A20040A R
554031 CONDENSER ASSEMBLY,BENDING 5403A20059B 5403A20059B 5403A20199D/F 5403A20198M 5403A20059U R
546810 MOTOR,UNCLASSIFIED 4681A20121B 4681A20121B 4681A20121D 4681A20121E 4681A20121B R
559010 FAN ASSEMBLY,PROPELLER 5900AR1266C 5900AR1266C 5901A10055B 5901A10055A 5900AR1266A R
554160 COMPRESSOR SET,KOREA 2520UCDK028 5417A20012H 2520UKMP2BA 2520UKMP2BA 5416A20013L R
567502 OVERLOAD PROTECT 6750U-L014A 6750A30001C 6750U-L027A 6750U-L027A 6750A30001C R
550140 DAMPER,COMPRESSOR 4H00982E 4H00982E 4H00982E 4H00982E 4H00982E R
552116 TUBE ASSEMBLY,REVERSE 5211A23317A 5211A21027F 5211A29021C - - R
552202 VALVE,REVERSE 5220AR3084E 5220AR3084E 5220AR3084E - - R
552111 TUBE ASSEMBLY,CONDENSER(OUT) 5211A23318A 5211A20133Z 5211A10197Y 5211A21143M 5211A20133Z R
552201 VALVE,CHECK - - 3H01552F - - R
552102-1 TUBE,CAPILLARY BENDING 5210A22614L 5210A20595F 5210A23613A 5210A22614H 5210A20595F R
552102-2 TUBE,CAPILLARY BENDING - - 5210A23613B - - R
649950 CASE ASSEMBLY,CONTROL(OUTDOOR) 4995A90162A 4995A10032V 4995A90441A 4995A90441B 4995A90162D R
W0CZZ-2 CAPACITOR,FILM,BOX - - 2H01451T - 2H01451P R
561410 SOLENOID 3A02028Y 3A02028Y 3A02028Y - - R
237204-1 PANEL,SIDE - - 3720A10238A 3720A29001A - R
237204-2 PANEL,SIDE - - 3720A10239A 3720A10239A - R
435300 GRILLE,REAR - - 3530A10251B 3530A10251B - R
437212 PANEL,REAR 3720A10172A 3720A10172A - - 3720A10172C R
447910 BARRIER,OUTDOOR 4790A10025D 4790A10025D 4790A10057B 4790A10057B 4790A10025D R
435511 COVER ASSEMBLY,CONTROL(OUTDOOR) 3551A30115D 3551A30115D 3551A30136A 3551A30136A 3551A30023W R
437211 PANEL ASSEMBLY,FRONT(OUTDOOR) 3720A10171A 3720A10171A 3721A10153B 3721A10153B 3721A20258A R
435301 GRILLE,DISCHARGE 3530A10059G 3530A10059G 3530A10250B 3530A10250B 3530A10059H R
Service Manual 63

Parts List (Outdoor)

LOCATION PART No.
DESCRIPTION REMARKS
No. AS-H0766KA2 AS-H0966KA2 AS-H126RKA2 AS-H186TKA2 AS-H246TKA2
430410 BASE ASSEMBLY,OUTDOOR 3040A20079A 3041A20079A 3041A20072D 3041A10027A 3041A30003H R
435511 COVER ASSEMBLY,CONTROL(OUTDOOR) 3551A30115D 3551A30115D 3551A30136A 3551A30079N 3551A30007X R
437210 PANEL ASSEMBLY,FRONT(OUTDOOR) 3721A20258A 3721A20258A 3721A10153B 3721A20260A 3721A20005H R
237204 PANEL SIDE - - 3720A29001A - - R
237205 PANEL SIDE - - 3720A10239A - - R
437212 GRILLE,REAR - - 3530A10251B - - R
437212 PANEL,REAR 3720A10172C 3720A10172C - 3721A20114F 3720AP0003D R
447910 BARRIER,OUTDOOR 4790A10025D 4790A10025D 4790A10057B 4791A20023C 2H02110M R
546810 MOTOR ASSEMBLY,OUTDOOR 4681A20121B 4681A20121B 4681A20121D 4681A20028P 4681A20013D R
550140 ISOLATOR,COMP 4H00982E 4H00982E 4H00982E 5014A20003A 4H00982E R
552102-1 TUBE,CAPILLARY BEND 5210A21238R 5210A21238X 5210A21146U 5210A31442N 5210A30216P R
552111 TUBE ASSEMBLY,CAPILLARY 5211A21143C 5211A21143J 5211A10197X 5211A21471A 5211A10039U R
552116 TUBE ASSEMBLY,REVERSING 5211A20188T 5211A20188P 5211A29021A 5211A20270P 5211A20529H R
552201 VALVE,CHECK - - - 5220A30004A 5220A30004A R
552202 VALVE,REVERSING 5220AR3228J 5220AR3228J 5220AR3228D 5220AR3228E 5220AR3228C R
552203-1 VALVE,SERVICE 5220A20005B 5220A20005B 5220A20006J 5220A20005B 5220A20001R R
552203-2 VALVE,SERVICE 5220A20001Q 5220A20001Q 5220A20005B 5220A20006J 5220A20013A R
554031 CONDENSER ASSEMBLY,BENT 5403A20059L 5403A20059L 5403A20199B 5403A20164F 5403A20022F R
554160 COMPRESSOR SET 2520UZBP2AA 2520UGAP2HB 2520UGHP2AA 2520UTEP2AA 2520UXFP2AA R
559010 FAN ASSEMBLY,PROPELLER 5900AR1266C 5900AR1266A 5901A10055A 5901A10032A 1A00195B R
561410 COIL ASSEMBLY,REVERSING VALVE 6141A20017A 6141A20017A 6141A20017A 3A02058Y 3A02028Y R
567502 O.L.P 6750U3L023A 6750U-L061A 6750U-L076A - - R
649950 CONTROL BOX ASSEMBLY,OUTDOOR 4995A90162A 4995A90162C 4995A90441A 4995A00006B 4995A10002L R
W0CZZ CAPACITOR,DRAWING - - - 2A00986Y 2A00986Y R
435301 GRILLE,DISCHARGE 3530A10059H 3530A10059H 3530A10250B 3530A20007J 3530A20007B R

Parts List (Outdoor)

LOCATION PART No.
DESCRIPTION REMARKS
No. LS-H0766KA2 LS-H0966KA2 LS-H126RKA2 LS-C126RKA2 LS-C0966KA2
430410 Base Assembly,Outdoor 3041A20079A 3041A20079A 3041A20072D 3041A20072B 3041A20079A R
552203-1 Valve,Service 2H02479P 2H02479P 5220A20005B 5220A20005B 2H02479P R
552203-2 Valve,Service 5220A20040A 5220A20040A 2H01890P 2H01890P 5220A20040A R
554031 Condenser Assembly,Bending 5403A20059B 5403A20059B 5403A20199D/F 5403A20198M 5403A20059U R
546810 Motor,Unclassified 4681A20121B 4681A20121B 4681A20121D 4681A20121E 4681A20121B R
559010 Fan Assembly,Propeller 5900AR1266C 5900AR1266C 5901A10055B 5901A10055A 5900AR1266A R
554160 Compressor Set,Korea 2520UCDK028 5417A20012H 2520UKMP2BA 2520UKMP2BA 5416A20013L R
567502 Overload Protect 6750U-L014A 6750A30001C 6750U-L027A 6750U-L027A 6750A30001C R
550140 Damper,Compressor 4H00982E 4H00982E 4H00982E 4H00982E 4H00982E R
552116 Tube Assembly,Reverse 5211A23317A 5211A21027F 5211A29021C - - R
552202 Valve,Reverse 5220AR3084E 5220AR3084E 5220AR3084E - - R
552111 Tube Assembly,Condenser(Out) 5211A23318A 5211A20133Z 5211A10197Y 5211A21143M 5211A20133Z R
552201 Valve,Check - - 3H01552F - - R
552102-1 Tube,Capillary Bending 5210A22614L 5210A20595F 5210A23613A 5210A22614H 5210A20595F R
552102-2 Tube,Capillary Bending - - 5210A23613B - - R
649950 Case Assembly,Control(Outdoor) 4995A90162A 4995A10032V 4995A90441A 4995A90441B 4995A90162D R
W0CZZ-2 Capacitor,Film,Box - - 2H01451T - 2H01451P R
561410 Solenoid 3A02028Y 3A02028Y 3A02028Y - - R
237204-1 Panel,Side - - 3720A10238A 3720A29001A - R
237204-2 Panel,Side - - 3720A10239A 3720A10239A - R
435300 Grille,Rear - - 3530A10251B 3530A10251B - R
437212 Panel,Rear 3720A10172A 3720A10172A - - 3720A10172C R
447910 Barrier,Outdoor 4790A10025D 4790A10025D 4790A10057B 4790A10057B 4790A10025D R
435511 Cover Assembly,Control(Outdoor) 3551A30115D 3551A30115D 3551A30136A 3551A30136A 3551A30023W R
437211 Panel Assembly,Front(Outdoor) 3720A10171A 3720A10171A 3721A10153B 3721A10153B 3721A20258A R
435301 Grille,Discharge 3530A10059G 3530A10059G 3530A10250B 3530A10250B 3530A10059H R
Service Manual 65

October, 2006
P/No.: 3828A20462C Printed in Korea

Manual de Servicio Aire Acondicionado LG

Uploaded by

Copyright:

Available Formats

Manual de Servicio Aire Acondicionado LG

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual de Servicio Aire Acondicionado LG

Uploaded by

Copyright:

Available Formats

website http://biz.LGservice.

Downloaded from www.Manualslib.com manuals search engine

2 Room Air Conditioner

Downloaded from www.Manualslib.com manuals search engine

1 Producing Center, A~Z L: Chang-won R22 N: India

3 Cooling/Heating/Inverter A~Z C: Cooling only V: AC Inverter C/O

4, 5 Capacity 0~9 Cooling/Heating Capacity

6 Electric Range 1~9 1: 115V/60Hz, A: 220V, 50Hz, 3Phase

7 Chassis A~Z Name of Chassis of Unit

8 Look A~Z Look,

Downloaded from www.Manualslib.com manuals search engine

1 Producing Center, A~Z L: Chang-won R22 N: India

3 Cooling/Heating/Inverter A~Z C: Cooling only V: AC Inverter C/O

9 Function A~Z Basic A

10 Serial No. 1~9 LG Model Development Serial No.

4 Room Air Conditioner

Downloaded from www.Manualslib.com manuals search engine

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

Be sure not to do.

Be sure to follow the instruction.

• There is risk of fire of electric shock. • There is risk of electric shock.

Downloaded from www.Manualslib.com manuals search engine

6 Room Air Conditioner

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

8 Room Air Conditioner

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

NOTICE This symbol indicates special notes.

D mm 155 156 172

10 Room Air Conditioner

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

12 Room Air Conditioner

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Power Cord 1.0mm2 1.0mm2 1.0mm2 3 x 1.5mm2 3 x 2.5mm2

14 Room Air Conditioner

Downloaded from www.Manualslib.com manuals search engine

Power Cord 1.0mm2 1.0mm2 1.0mm2 1.0mm2 1.0mm2

Downloaded from www.Manualslib.com manuals search engine

More than 2.3m More than "B"

Install the indoor unit on the wall where the height

16 Room Air Conditioner

Downloaded from www.Manualslib.com manuals search engine

How to Fix Installation Plate Drill a Hole in the Wall

Drain hose junction

A drain hose and connecting hose according to the figure

CHASSIS Distance (mm)

Right rear piping Ø70mm Only the

Downloaded from www.Manualslib.com manuals search engine

Flaring work and connection of piping

Burr removal = Improper flaring =

Bar Bar remaining parts must be removed

18 Room Air Conditioner

Downloaded from www.Manualslib.com manuals search engine

Outside diameter Torque

Downloaded from www.Manualslib.com manuals search engine

Wrench Connection pipe