peretn is considered subject to change at any time and at our disretion 5.7 Dip-Switches and functions SAFETY ‘The safety features can be connected and designated for: - Re-opening during closure (2-61) Re-closing during opening (2-CX, see dip 8-9); ~ Partial top gate stops ifn mation with the resulting preparation for automatic closing (2-CX, see dip 8-9); Total stop (1-2), gate stop, excluding any automatic closing cycie; to resume movement, you must use the pushbutton panel or transmitter NOTE: It an N.C. safety contact (2-C1, 2-CX, 1-2) is opened, the LED wil lash to indicate this fact. ~ Obstacle detection With the motor not running (gate closed, open, o after a total stop command), this feature hinders any movement If the safety devices (e.g. photoelectric cells) detect an obstacle; ~ Safety test function ‘At every gate opening and closure command, the control unit checks the efficiency ofthe safety features Possible accessories ~ Gycle or courtesy lamp (60W); OTHER SELECTABLE FUNCTIONS ~ Automatic closure. The automatic closure timer self-powers at the opening end stop. The modifiable set time is also subject to ‘modifications due to the intervention of possible safety accessories. This does not happen following a complete “stop command orif power is cut ~ Partial opening. Opening of the gate to allow for pedestrian traffic; activated by connecting to clamps 2-3P and adjusted with the PART. OP trimmer. With this function, the automatic closing can vary inthe following way: 1) Dip 12 set to ON: after a partial opening, the time for automatic closing functions independently ofthe adjustment of the TCA trimmer and of the position of Dip 4; itis set at 8 seconds. 2) Dip 12 set to OFF: ater a partial opening, the time for automatic closing is adjustable only if Dip 1 is set to ON;~MYCIE AMD. A TIGHT nat Huminales the manoeuvring zone. Kt remains NE TTOM the moment the Goors Degin To Open Until iney are completely closed (including the time required forthe automatic closure). | automatic closing is not activated, the lamp remains on enly during mavement (E-EX); ~ Courtesy Light. A light that illuminates the manoeuvring zone: after an opening command, the light remains on fora fixed time ‘of 5 minutes and 30 seconds (E-EX); ‘Maintained Action” function. Gate operation while keeping the pushbutton pressed (excludes the radio-control operation); ~ Pre-flashing: § seconds pre-flash during both opening and closing ofthe wing: - Master function; the panel assumes all the command functions when two paired motors are used (see page 30); + Slave function; this panel is exclusively controlled by the “MASTER"; Enabling functions of partial stop or closure whist opening, normally-closed contact (2-CX%), select one of the two functions by setting Dip (see Function selections) Type ot command: -open-close-reverse by button and transmitter; -open-stop-close-stop by button and transmitter, open only by transmitter. ADJUSTMENTS automatic closing time; Partial opening time.‘Automatic closure activated; (1 OFF-deactivated) “Open-stop-close-stop” function with button (2-7) and transmitter (AF board inserted) activated; ~"Open-close” function with button (2-7) and transmitter (AF card inserted) activated; Only opening” function with transmitter (AF card inserted) activated; (3 OFF deactivated) "Maintained Action” function (excludes the function ofthe transmitter) activated; (4 OFF-deactivated) “Pre-flashing during opening/closing activated; (5 OFF-deactivated) -Obstacle detection activated; (6 OFF-deactivated) “Re-clasing while opening” function (connect the safety device on clamps 2-C1) activated; (7 ON-deactivated) e-closing while opening” function (connect the safety device on clamps 2-CX) activated; Partial stop” function (connect the safety device on clamps 2-CX) activate: (ifthe devices on the 2-CX clamps are not used, set Dip & to ON) Total stop” function (connect the button onto clamps 1-2) activated; (10 ON - deactivated) ~*Slave" function deactivated (fo activate in the evant of coupled connection) “Partial opening” function (automatic closing is fixed at 8 seconds) activated; Partial opening” function (automatic closing Is adjusted with the trimmer, if onvinserted) activated; "Safety test function to check the efficiency ofthe photoelectric cells (see page 14) activated; (13 OFF-deactivated) jarein is considered subject to change at any time and at our discretion14 OFF “Master” function deactivated (to activate in the event of coupled connection); 15 - Not used, keep the dip switch in the “OFF” position 16 0N "Courtesy light function activated”; (16 OFF-deactivated) 1ZON “Lamp cycle” activated; (17 OFF-deactivated) ‘180N ~ Activates brake during closure- (CBX, CBXT). 19 ~ Not connected 20 ~ Not connected 5.8 Adjustment Trimmer TC.A= HAP PAR 5 OETA ‘Timmer T.C.A, = Adjusts automatic closing time from a minimum of 1 sec to a maximum of 120 sec. Part. Op. Trimmer, = Adjusts automatic opening time from a minimum of 1 sec to a maximum of 14 sec “ile data and information contained |peretn is considered subject to change at any time and at our disretion 9 Connection of two panels for control of coupled motors Coordinate the direction of the A" and “B" gearmotors, ‘modifying the rotation of motor “B” (see end stop connec- ton on the motor manual) + Set the master (or pilot) motor between A and B by setting dip-switeh 14 to ON on the control board. The “master” designation means that the motor that controls both gates, while on the control board of the 2nd motor, set the dip 11 (on ON to make it inoperable (slave) (1). ~ Make sure thatthe radiofrequency card is only inserted on the MASTER board (2); make the electrical connections and the normally used selections only on the MASTER terminal board (3); — Execute the connections between the clamos 2s shown in Sched radiotrequenza “AF” Scheda Base “Master” myAll tha data and information contained Fig. A = Make sure that all the dipswitches on the board of the 2nd motor are OFF, except for dip 11 (4). AML j0TE: ifthe wo couptes gates are of tterent sizes, te master function must be inserted in the motor control board installed on the longer door. MASTER5.10 Installation of radio-controls A-INSERT AN AF CARD **. B- ENCODE TRANSMITTERS. C- STORE CODE IN THE BASE CARD. (A) AF BOARD INSERTION ay ae? eee = TP Ta Fan 26 995, ania 1 fut20 900 e150 rm Amz69n5 A006 oP amans00 aan oP pe nego (°*) Fortransmites with 493.92 Supertarendinatequeny (TOP and wee ee sole TAM sees), position the jumper as lustated onthe respective AF 43S amanses aa Tov m SHEDA “AP a te Aboard shout ALWAYS be inserted when the power i ff because th motherboard oly recognises it when tis powered jarein is considered subject to change at any time and at our discretion(B) TRANSMITTER ENCODING arom ‘ATOM - ATO2 - ATO see instruction sheet inside the package ofthe AFAR. TOP 432M -T312M. Set the code to dip-switeh C and channel to D (P1=CH1 and P2=CH, detaut seting) “ile data and information contained | 10peretn is considered subject to change at any time and at our disretion TOP 434M - T3140 PI = cH Po =H? P2=CH3 P4=CHA Set code only TOP 4925 - 434MA- 432NA ‘See instruction sheet inside the fC package Tam Tri 1432 - 1434-1438 1132-1134 - 1138 1152 -T154 - 1158 ‘See instruction sheet inside the package % See instruction sheet inside the package ‘TOP QUARZATI ‘STANDARD ENCODING PROCEDUREmn a code (also for records) 2. insert jumper code J 3.save it 4, disconnect jumper J ne P2 ‘ON 123456789 Press P1 or P2 in sequence in order to register the code; atthe tenth pulse, a double beep will confirm that the code is saved, nTCH 4024 -ToH 4048 See instruction sheet inside the package oP 262m - T302M The first encoding operation must be carried out whilst keeping the jumpers po- sitioned for channels 1 and 2 as per tig. A; see tig. B for any subsequent settings on different channels, PL=CHI-P2=CH3 FIG. PL=CH3-P2=CH2 neoreoe (OU 4d P1=CH3-P2 = GHA jarein is considered subject to change at any time and at our discretion264m - T304M PrcHl P2=cH2 P3= CHI P4=CHd ; (nae ae + — ‘Te62aM - Ts0z2M 1° Codioe Pi=cHI P2=0H2 2 codice Po=cHI Pas che la and information comtaned‘app TO Ye Ue BU se Ye @BUELD 0 ATS PalaprSUOD STWRBPUTEIUO® UORETORN PUR BIER Oy 5‘CAME UNITED KINGDOM LTD UNIT3, ORCHARD BUSINESS PARK TOWN STREET, SANDIACRE NOTTINGHAM - G10 SBP - UK. Tel 0044 115 9210430 Fax 0044115 9210431o Tf Lu oO