Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 27 views

    Calibracion Regulador

    Uploaded by

    Ronaldo Galeano
    This document provides instructions for testing the pump control pilot pressure signal on an excavator. Specifications for hydraulic oil temperature, engine speed, power mode switch position, and idle switch position are listed. The test checks that the regulated pump control pilot pressure decreases when functions are actuated and increases when returning to neutral. Technicians are instructed to install pressure measurement equipment, warm the hydraulic oil, run the machine at specifications, and record pump control pressures in neutral and at full stroke to check they meet standards.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Calibracion Regulador

    Uploaded by

    Ronaldo Galeano
    27 views2 pages
    This document provides instructions for testing the pump control pilot pressure signal on an excavator. Specifications for hydraulic oil temperature, engine speed, power mode switch position, and idle switch position are listed. The test checks that the regulated pump control pilot pressure decreases when functions are actuated and increases when returning to neutral. Technicians are instructed to install pressure measurement equipment, warm the hydraulic oil, run the machine at specifications, and record pump control pressures in neutral and at full stroke to check they meet standards.

    Original Title

    calibracion regulador

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for testing the pump control pilot pressure signal on an excavator. Specifications for hydraulic oil temperature, engine speed, power mode switch position, and idle switch position are listed. The test checks that the regulated pump control pilot pressure decreases when functions are actuated and increases when returning to neutral. Technicians are instructed to install pressure measurement equipment, warm the hydraulic oil, run the machine at specifications, and record pump control pressures in neutral and at full stroke to check they meet standards.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    27 views2 pages

    Calibracion Regulador

    Uploaded by

    Ronaldo Galeano
    This document provides instructions for testing the pump control pilot pressure signal on an excavator. Specifications for hydraulic oil temperature, engine speed, power mode switch position, and idle switch position are listed. The test checks that the regulated pump control pilot pressure decreases when functions are actuated and increases when returning to neutral. Technicians are instructed to install pressure measurement equipment, warm the hydraulic oil, run the machine at specifications, and record pump control pressures in neutral and at full stroke to check they meet standards.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Page 1 of 2

    TM11583 - XCG210LC-8B Excavator Operation and Test


    Pump Control Pilot Pressure Signal Test

    Pump Control Pilot Pressure Signal Test

    -: Specifications

    SPECIFICATIONS
    Hydraulic Oil Temperature 45—55° C
    110—130° F
    Engine Speed (approximate) 1800 rpm
    Power Mode Switch Position S (standard)
    Auto Idle Switch Position Off
    Pump 1 or Pump 2 Control Pressure in Neutral State Pressure (approximate) 2.8 MPa
    2 800 kPa
    28.0 bar
    406 psi
    Pump 1 or Pump 2 Control Pressure in Full Stroke Pressure .55 MPa
    551.6 kPa
    5.5 bar
    80 psi

    -: Service Equipment and Tools

    SERVICE EQUIPMENT AND TOOLS


    JT02156A Digital Pressure and Temperature Analyzer
    JT02162 Transducer 35 000 kPa (350 bar) (5000 psi)
    Gauge 7000 kPa (70 bar) (1000 psi)

    The function of the pump 1 and pump 2 regulators is to change pump flow in response to the actuation of pilot control valves
    to shift the control valve spools.

    The purpose of this test is to check that the regulated pump control pilot pressure signal from the flow rate pilot valves to the
    remote control spool in pump 1 and pump 2 regulators decreases as a function is actuated and increases when function is
    returned to neutral.

    1. Release hydraulic oil tank pressure. See Hydraulic Oil Tank Pressure Release Procedure . (Group 9025-25.)

    2.
    TX1071663A-UN: Pump Control Pilot Pressure Signal Test

    LEGEND:

    1 - Transducer
    2 - Pilot Pressure Hose
    3 - Adapter Tee Fitting
    4 - Pump Pressure Regulator

    Disconnect pilot pressure hose (2) and install adapter tee fitting (3) for testing.

    file:///C:/ProgramData/Service%20ADVISOR/Temp/TM11583_09001faa811419c8.ht... 19/04/2020
    Page 2 of 2

    3. Install JT02156A Digital Pressure/Temperature Analyzer and JT02162 Transducer or 7 000 kPa (70 bar) (1000 psi)
    gauge to tee fitting. See JT02156A Digital Pressure/Temperature Analyzer Installation . (Group 9025-25.)

    4. Warm hydraulic oil to specification. See Hydraulic Oil Warm-Up Procedure . (Group 9025-25.)

    Item Measurement Specification

    Hydraulic Oil Temperature 45—55° C


    110—130° F

    5. Run machine at specifications.

    Item Measurement Specification

    Engine Speed (approximate) 1800 rpm

    Power Mode Switch Position S (standard)

    Auto Idle Switch Position Off

    6. Return all controls to neutral and record pump control pressure.

    Item Measurement Specification

    Pump 1 or Pump 2 Control Pressure Pressure (approximate) 2.8 MPa


    in Neutral State 2 800 kPa
    28.0 bar
    406 psi

    7.

    CAUTION:

    Prevent possible injury from machine movement. Ensure that area is clear of bystanders and
    large enough to operate all machine functions.

    Actuate boom up control lever to full stroke. Pressure reading should decrease as lever moves. Operate function to full
    stroke and record pump control pressure.

    Item Measurement Specification

    Pump 1 or Pump 2 Control Pressure Pressure .55 MPa


    in Full Stroke 551.6 kPa
    5.5 bar
    80 psi

    TP97644,000013C-19-20100311

    file:///C:/ProgramData/Service%20ADVISOR/Temp/TM11583_09001faa811419c8.ht... 19/04/2020

    You might also like