Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 18 views

    Transmission Pump Flow Test

    Uploaded by

    Lupin Gonzalez
    770CH II

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Transmission Pump Flow Test

    Uploaded by

    Lupin Gonzalez
    18 views2 pages
    770CH II

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    770CH II

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    18 views2 pages

    Transmission Pump Flow Test

    Uploaded by

    Lupin Gonzalez
    770CH II

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Page 1 of 2

    TM1914 - C Series II Motor Graders Operation and Test


    Transmission Pump Flow Test

    Transmission Pump Flow Test

    -: Specifications

    SPECIFICATIONS
    Oil Temperature 43 ± 6°C (110 ± 10°F)
    Transmission Pressure 1862 ± 103 kPa (18.6 ± 1.0 bar) (270 ± 15 psi)
    Engine Speed 2000 ± 5 rpm
    Pump Typical New Flow 98 L/min (26 gpm)
    Pump Minimum Allowable Flow 76 L/min (20 gpm)

    -: Essential Tools

    ESSENTIAL TOOLS
    38H1194 (1 5/16 ORB x -12 M ORFS) Adapter (2 used)

    -: Service Equipment And Tools

    SERVICE EQUIPMENT AND TOOLS


    JT05800 Digital Thermometer
    JT05801 Electronic Tachometer
    Flow Meter

    1. Connect thermometer. See Digital Thermometer Installation . (See procedure in this group.)

    2. NOTE:

    Monitor tachometer in the machine can be used. See Calibration procedure in Group 9015-20.

    See JT05801 Clamp-On Electronic Tachometer Installation. (Go to 9010.)

    3. Install flow meter between transmission and transmission oil filter.

    4. IMPORTANT:

    Flow meter loading valve must be open before starting the engine and during the test to prevent damage
    to the transmission pump.

    Open flow meter loading valve.

    5. Check and correct transmission oil level. See Check Transmission Oil Level

    (Go to Operators Manual group 60.)

    6. Heat transmission oil to test specifications. (See Transmission and Axle Oil Warm-Up Procedure in this group.) Access
    Transmission Pump Flow Test SERVICE ADVISOR™ system template for readings.

    Item Measurement Specification

    Oil Temperature 43 ± 6°C (110 ± 10°F)

    file:///C:/ProgramData/Service%20ADVISOR/Temp/TM1914_09001faa8027c588.html 17/08/2024
    Page 2 of 2

    7. Place transmission control and park brake lever in park “P” position.

    8. Check transmission pressure. If pressure is not within specification, adjust pressure. (See Transmission System
    Pressure Test in this group).

    Item Measurement Specification

    Transmission Pressure 1862 ± 103 kPa (18.6 ± 1.0 bar)


    (270 ± 15 psi)

    9. Run engine at specified speed and record flow.

    Item Measurement Specification

    Engine Speed 2000 ± 5 rpm

    If flow is not within specifications, replace transmission filter, check pump suction tube and end fittings for air leaks,
    remove and clean transmission suction screen and test flow again.

    Item Measurement Specification

    Pump Typical New Flow 98 L/min (26 gpm)

    Pump Minimum Allowable Flow 76 L/min (20 gpm)

    If still low replace pump.

    SERVICE ADVISOR is a trademark of Deere & Company CED,OUOE035,177-19-19980616

    file:///C:/ProgramData/Service%20ADVISOR/Temp/TM1914_09001faa8027c588.html 17/08/2024

    You might also like