Fosroc Nitoflor ET Slurry constructive solutions

Formerly known as Cicol ET Slurry

Heavy duty, lightweight, anti-skid flooring system

Uses Properties
Nitoflor ET Slurry provides a lightweight, yet extremely hard Pot life at 25ºC : 70 mins
wearing anti-skid surface waterproof to a variety of substrates Specific gravity : 1.67
including steel, concrete, asphalt and timber. Curing time at 20ºC : Foot traffic after 24 hours,
vehicular traffic after 48 hours
Ideally suited for foot and road bridges, RO/RO linkspans, work
Water permeability : Nil
platforms, car parks, walkways, Helicopter pads, wet work
(at 5 bar pressure)
industrial areas and cargo handling areas, etc.
BSEN 12390 P8 (BD47)
Water absorption : Nil
Advantages
(ASTM C413)
 Lightweight Compressive strength : Tolerance (±10%)
 Hard wearing (ASTM C579) : >45N/mm2
Resistance to high
 Flexible
temperature : No sign or dripping
 Excellent adhesion to steel and concrete substrates 1500C during asphalt
 Non-slip, excellent grip even when wet placing ASTM D1227 (BD47)
 Chemically resistant Resistance to chisel
 Waterproof impact : No cracks or indentation
(BD47) were observed
 Zero spread of flame
Adhesion to concrete : Greater than the tensile
(BS1881 P207) strength of concrete
Description
Resistance to
Nitoflor ET Slurry is a three component system based upon Pin/Blow holing : No blisters or pin holes
solvent free, coal tar modified epoxy resins, amine curing Resistance to abrasion : High abrasion resistance
agents and chemically inert, graded silica fillers which when
mixed forms a fluid, homogeneous slurry. <10mg
(using taber abraser
Specially selected Dynagrip aggregates are broadcast onto
ASTM D4060)
this slurry whilst it is still wet to provide a lightweight, flexible,
CS17, 1000g, 1000 cycles
durable, anti-skid dressing which can be used on a variety of
Crack Bridging ability : >2.0mm
substrates including steel, concrete, timber and aluminium.
ASTM C836

Design criteria Fully cured Nitoflor ET Slurry has been shown to be resistant
to the following chemicals after continuous immersion for 12
The thickness of the Nitoflor ET Slurry is varied to suit traffic
months at 20ºC:
conditions as shown in the table below.
Chemical resistance : Petrol
Traffic Nitoflor ET Slurry Aggregate Nominal
Kerosene
density thickness type thickness
Hydraulic fluids,
Medium : 3.0mm 20 mesh 3.5mm
Dilute mineral acids and
Heavy : 3.0mm 1 to 3mm 5.5mm
alkalis10% Urea in
The final thickness of the finished surface dressing will be water De-icing salts
between 3.5 to 5.5mm depending upon the exact system Diesel
chosen to meet the expected end use. Aircraft fuel

When used as a bridge deck waterproofing membrane

1-3mm aggregate should be used.

Nitoflor ET Slurry HB* is recommended on ramps with a

Nitoflor ET Slurry

slope greater than 5 degrees.

Fosroc Nitoflor ET Slurry

Instructions for use Mixing

Preparation Mix the base and hardener thoroughly using a slow speed
drill and Fosroc Mixing Paddle (MR3), or forced action mixers
Nitoflor ET Slurry can be applied to a variety of substrates. As
such as creteangle or zyklos. Add the mineral fillers and mix
with all flooring materials or protective coatings, correct
until a homogeneous slurry consistency is formed. The total
surface preparation is essential.
mixing operation should take about 5-7 minutes.
Steel substrates
The Nitoflor ET Slurry is now ready for use. Do not add
Nitoflor ET Slurry is specially formulated to exhibit excellent thinners or solvent.
adhesion to un-primed steel. However, all steel substrates
Application
should be blast cleaned to a minimum SA21/2 standard of
cleanliness. An angular profile amplitude of at least 75 Once mixed the Nitoflor ET Slurry must be used within the
microns is recommended. specified pot life.

The slurry should be applied as quickly as possible to the Pour the slurry onto the prepared surface. Work in lanes of
blasted steel surface. If the standard of the surface falls below 2-3 m wide masking off edges with tape. Spread the slurry
SA21/2 then the steel must be reblasted. using a steel trowel or squeegee taking particular care when
joining up to the previous day’s work.
Concrete substrates
Use of a wet film gauge is recommended to ensure the
Nitoflor ET Slurry is applied to clean, sound, dry concrete
correct thickness and material usage. The Dynagrip surface
substrates which are free of any laitance or loose particles.
dressing aggregate must be applied immediately after laying
Mechanical scarifying or blasting methods are strongly
the Nitoflor ET Slurry.
recommended.
The slurry coating is blinded to saturation by allowing the
Prepared concrete substrates should be primed with Nito-
aggregate to fall vertically until no slurry is visible. Do not
prime 25 which is applied by lambswool roller to provide a thin
throw aggregate across the slurry as this may cause ridges.
even coverage. Avoid over application and puddles. Nitoflor
Masking tape must be removed before the coating has cured.
ET Slurry is applied onto the Nitoprime 25 as soon as it is free
from surface tack. The Nitoflor ET Slurry must be allowed to cure for 24 hours at
20ºC before being subject to foot traffic. At lower tempera-
Asphalt substrates
tures this period will be increased.
Nitoflor ET Slurry can be applied onto asphalt substrates
Cleaning
providing they are clean, sound and dry. It is also recommend-
ed that the asphalt should be at least 12 months old. All tools can be cleaned immediately after use with Fosroc
Solvent 102.
Asphalt should be lightly grit blasted to remove any weakly
bonded or contaminated material to provide the desired
Limitations
surface. No primer is required on asphalt.
 Nitoflor ET Slurry should not be applied when the relative
Wooden substrates
humidity is greater than 80% or the ambient temperature
Nitoflor ET Slurry can be applied directly onto clean, dry is expected to fall below 5°C.
timber substrates.
 Nitoflor ET Slurry should not be applied on ramps with a
Aluminium substrates slope greater than 5 degrees.

Must be sweep blasted and degreased if necessary using

Technical support
Fosroc Solvent 102* to provide a sound mechanical key.
Nitoflor ET Slurry can be applied directly to the prepared Fosroc offers a comprehensive range of high performance, high
substrate. quality flooring, jointing and repair products for both new and
existing floor surfaces. In addition, Fosroc offers a technical
support package to specifiers, end users and contractors, as
well as on-site technical assistance in locations all over the
world.

Nitoflor ET Slurry - Page 2 of 4

Fosroc Nitoflor ET Slurry

Estimating Precautions
Supply Health and safety
Nitoflor ET Slurry : 20 litre packs
Nitoflor ET Slurry, Nitoprime 25 and Solvent 102 should not
Nitoprime 25 : 1 & 4 litre packs
come into contact with the skin or eyes, or be swallowed.
Coverage Ensure adequate ventilation and avoid inhalation of vapours.
Nitoflor ET Slurry : 3.0 litre/m2 @ 3mm thick
Some people are sensitive to resins, hardeners and solvents.
Dynagrip
Wear suitable protective clothing, gloves and eye protection.
Aggregate Gross (kg/m2) Net (kg/m2)
If working in confined areas, suitable respiratory protective
20 mesh 5.5 3.7
equipment must be used.
1.0 to 3.0 7.0 5.2
Nitoprime 25 : 4.0 - 5.0 m2/litre The use of barrier creams provide additional skin protection.
In case of contact with skin, rinse with plenty of clean water,
Notes : Coverage figures given are theoretical - due to
then cleanse with soap and water. Do not use solvent.
wastage factors and the variety and nature of
possible substrates, practical coverage figures will In case of contact with eyes, rinse immediately with plenty of
be reduced - site trials are recommended. clean water and seek medical advise. If swallowed, seek
medical attention immediately - do not induce vomiting.
For “specialised uses”, please contact the local
Fosroc office for coverage figures. Fire

Fosroc Solvent 102 is flammable. Ensure adequate ventila-

Storage
tion. Do not use near naked flame. Do not smoke.
Shelf life

All products have a shelf life of 12 months if kept in a dry store

in the original, unopened packs.

Storage conditions

Store in dry conditions between 5ºC and 30ºC away from

sources of heat and naked flames, in the original, unopened
packs. If stored at high temperatures the shelf life will be
reduced.

Flash points (Abel closed cup)

Fosroc Solvent 102 : 33°C
Nitoprime 25 : 39°C

Nitoflor ET Slurry - Page 3 of 4

Fosroc Nitoflor ET Slurry

Additional Information
Fosroc manufactures a wide range of complementary
products which include :

 waterproofing membranes & waterstops

 joint sealants & filler boards

 cementitious & epoxy grouts

 specialised flooring materials

Fosroc additionally offers a comprehensive package of

products specifically designed for the repair and refurbish-
ment of damaged concrete. Fosroc’s ‘Systematic Approach’
to concrete repair features the following :

 hand-placed repair mortars

 spray grade repair mortars

 fluid micro-concretes

 chemically resistant epoxy mortars

 anti-carbonation/anti-chloride protective coatings

 chemical and abrasion resistant coatings

For further information on any of the above, please consult

your local Fosroc office - as below.

* Denotes the trademark of Fosroc International Limited

†
See separate data sheet

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the latest version.

Fosroc Chemtech Head Office Alex. Branch

6th of October City, 3rd Industrial Zone, Arab Republic of Egypt. 156 Port-Said St. Al-Ibrahimeya, Kesm Bab
Construction Chemicals
Tel: (02) 38242045 / (02) 38242046 Shark-No.5,1st floor.
Fax: (02) 38242098 Tel: (03) 5925264
E-mail: Egypt@Fosroc.com

UAE/0302/20/I