Inj-24 Series Qig E4 0

INJ-24 Series
Quick Installation Guide

Moxa PoE Injector
Edition 4.0, February 2017
Technical Support Contact Information

www.moxa.com/support
Moxa Americas: Moxa China (Shanghai office):

Toll-free: 1-888-669-2872 Toll-free: 800-820-5036
Tel: 1-714-528-6777 Tel: +86-21-5258-9955
Fax: 1-714-528-6778 Fax: +86-21-5258-5505
Moxa Europe: Moxa Asia-Pacific:
Tel: +49-89-3 70 03 99-0 Tel: +886-2-8919-1230
Fax: +49-89-3 70 03 99-99 Fax: +886-2-8919-1231
Moxa India:
Tel: +91-80-4172-9088
Fax: +91-80-4132-1045
 2017 Moxa Inc. All rights reserved.
P/N: 1802000240013
*1802000240013*
Overview
The Moxa PoE Injector INJ-24 Series is a 1-port PoE injector that
delivers both data and electrical power to Ethernet-enabled devices using
a single Ethernet cable. The INJ-24 can supply up to 30 watts of power
through the Ethernet port, and can power IEEE 802.3af/at compliant
powered devices (PD), such as wireless access points or IP cameras,
eliminating the need for additional wiring. The INJ-24 supports Gigabit
communication, which is vital for high-speed and low-latency applications.
The INJ-24 also offers a wide operating temperature range of -40 to 75°C,
and is designed to withstand a high degree of vibration and shock. A
rugged hardware design makes the INJ-24 perfect for ensuring that your
Ethernet equipment can operate in critical industrial environments, such
as in hazardous locations, and complies with FCC and CE standards.
Wiring Requirements
WARNING
Do not disconnect modules or wires unless the power supply has
been switched off or the area is known to be non-hazardous. The
devices may only be connected to the supply voltage shown on
the type plate. The devices are designed for operation with a
Safety Extra-Low Voltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with the
Safety Extra-Low Voltages (SELV) in compliance with IEC
60950-1/EN 60950-1.
WARNING
The power for this product is intended to be supplied by a Listed
Power Unit, with output marked LPS, and rated to deliver 24 DC
at a maximum of 1.3 A.
WARNING
This unit is a built-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply with fire enclosure regulation IEC 60950-1/EN60950-1
(or similar regulation).
-2-
WARNING
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa PoE injector. Calculate the maximum possible
current in each power wire and common wire. Observe all
electrical codes dictating the maximum current allowable for each
wire size. If the current goes above the maximum ratings, the
wiring could overheat, causing serious damage to your
equipment.
You should also pay attention to the following items:

• Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
in the same wire conduit. To avoid interference, wires with different
signal characteristics should be routed separately.
• You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together.
• Keep input wiring and output wiring separated.
• It is strongly advised that you label wiring to all devices in the system
when necessary.
Package Checklist
The Moxa INJ-24 Series is shipped with the following items. If any of
these items is missing or damaged, contact a Moxa customer service
representative for assistance.
• Moxa PoE Injector INJ-24
• Quick installation guide (printed)
• Warranty card
Features
High Performance Network Switching Technology
• 10/100/1000BaseT(X)
• Provides up to 30 watts per PoE port
• Active circuit protection
• Auto disconnection for over voltage or under voltage
• Power consumption detection and classification
• Industrial-grade reliability
Rugged Design
• Operating temperature range from 0 to 60°C, or extended operating
temperature from -40 to 75°C for “T” models
• IP30, rugged high-strength case
• DIN-Rail or panel mounting ability
-3-
Panel Layout
1. Heat dissipation orifices

2. Terminal block for power input and grounding
3. Moxa Logo
4. Power LED
5. Data input port
6. PoE LED
7. PoE output port
8. DIN-Rail
-4-
Mounting Dimensions (unit = mm)
DIN-Rail Mounting
The plastic DIN-Rail attachment plate should already be fixed to the back
panel of INJ-24 when you take it out of the box. If you need to reattach
the DIN-Rail attachment plate, make sure the stiff metal spring is situated
towards the top, as shown in the figures below.
STEP 1: STEP 2:
Insert the top of the DIN-Rail into The DIN-Rail attachment unit will
the slot. snap into place as shown below.
-5-
To remove the INJ-24 from the
DIN-Rail, insert a flat-blade screw
driver horizontally into the DIN-Rail
kit under the INJ-24, and then pull it
upwards and release INJ-24 towards
you away from the DIN-Rail.
You may also take the following steps to remove the INJ-24 from the
DIN-Rail.
Step 1: Step 2:
Press the middle of the flat side of Release it towards you and away
the mounting kit as indicated. Pull from the DIN-Rail.
the INJ-24 downwards.
Grounding the INJ-24

Grounding and wire routing help limit the
effects of noise due to electromagnetic
interference (EMI). Run the right most contact
of the 3-contact terminal block to the grounding
surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well-grounded
mounting surface, such as a metal panel.
-6-
Wiring the INJ-24’s Power Outputs
The two left-most contacts of the 3-contact terminal block connector on
the INJ-24’s top panel are used for 24 VDC output. Top and front views of
one of the terminal block connectors are shown here.
STEP 1:
Insert the negative/positive DC wires into the V-/V+
terminals.
STEP 2:
To keep the DC wires from pulling loose, use a small
flat-blade screwdriver to tighten the wire-clamp
screws on the front of the terminal block connector.
STEP 3:
Insert the plastic terminal block connector prongs
into the terminal block receptor, which is located on
INJ-24’s top panel.
LED Indicators
Several LED indicators are located on the ING-24’s front panel. The
function of each LED is described in the table below.
LED Color State Description

On Power is being supplied
Power AMBER
Off Power is not being supplied
Power is being supplied to a
On
Powered Device (PD)
Blinking, 1.5 Hz No PoE power output
PoE AMBER
PoE failure:
Blinking, 10 Hz 1. PoE standard detection failure
2. PoE current overload
Specifications
Technology
Standards IEEE802.3, 802.3u, 802.3ab, 802.3af, 802.3at
Interface
RJ45 Ports 10/100/1000BaseT(X) speed
LED Indicators Power, PoE
PoE
Total Power Budget 30 W
PoE Output Voltage 50 @ 24/48 VDC (with full PoE loading)
PoE Output Power 15.4 W for 802.3af, 30 W for 802.3at
PoE Output Current 350 mA for 802.3af, 600 mA for 802.3at
Overload Current Present
Protection at Port
PoE Pinout Mode B: Pair 4, 5 (V+); Pair 7, 8 (V-)
-7-
Power
Input Voltage 24/48 VDC (22 to 57 VDC), single input
Input Current 1.4 A @ 24 VDC (with full PoE loading)
0.7 A @ 48 VDC (with full PoE loading)
Power Consumption Max. 3.6 W (with 1 PD connected, excluding
PD’s consumption)
Inrush Current 26.3 A @ 48 VDC
Electrical Isolation 2250 VDC to chassis for 60 s
Heat Dissipation 12.3 BTU/h
Overload Current Present
Protection at Input
Reverse Polarity Present
Protection
Connection 1 removable 3-contact terminal block
Mechanical
Housing IP30 protection, plastic case
Dimensions 25 × 109 × 88 mm (0.98 x 4.29 x 3.46 in)
Weight 115 g
Installation DIN-Rail, wall mounting
Environmental Limits
Operating Temperature Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature -40 to 85°C (-40 to 185°F)
Ambient Relative 5 to 95% (non-condensing)
Humidity
Regulatory Approvals
EMI FCC Part 15, CISPR 32 class A
EMS EN61000-4-2 (ESD), Level 3
EN61000-4-3 (RS), Level 3
EN61000-4-4 (EFT), Level 3
EN61000-4-5 (Surge), Level 3
EN61000-4-6 (CS), Level 3
EN61000-4-8, Level 5
Shock IEC60068-2-27
Freefall IEC60068-2-32
Vibration IEC60068-2-6
Warranty
Time Period 5 years
Details www.moxa.com/warranty
Patent http://www.moxa.com/doc/operations/Moxa_Patent_Marking.pdf
-8-

Inj-24 Series Qig E4 0

Uploaded by

Copyright:

Available Formats

Inj-24 Series Qig E4 0

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Inj-24 Series Qig E4 0

Uploaded by

Copyright:

Available Formats

INJ-24 Series

Quick Installation Guide

Edition 4.0, February 2017

Technical Support Contact Information

Moxa Americas: Moxa China (Shanghai office):

 2017 Moxa Inc. All rights reserved.

You should also pay attention to the following items:

1. Heat dissipation orifices

Grounding the INJ-24

LED Color State Description

You might also like