1.1.

SPECIFICATIONS

TABLE OF SPECIFICATIONS, NEW CLEARANCES, AND WEAR LIMITS

STANDARD BOLT AND NUT TORQUE SPECIFICATIONS

SIZE NUT TORQUE SIZE NUT TORQUE SIZE NUT TORQUE

OR BOLT (Ib-ftj OR BOLT (lb-ft) OR BOLT (lb-ft)

1/4 - 20 . . . ... 7-9 7/16 - 20 . . 57-61 3/4 - 10 240-250

1/4 - 28 . . . • . . A-in 1/2 - 13 . . . 71-75 3/4 - 16 290-300
5/16 - 18 . . . . . . 13-17 1/2 - 20 . . . . . . 83-93 7/8 - 9 410-420
5/16 - 24 . ; . . . 15-19 9/16 - 12 . . . . . . 90-100 7/R - 14 ’ 475-485
3/8 - 16 . . . 30-85 9/16 - 18 . . . . . . 107-117 1-A 580-590
3/8 - 24 : : : . . . 35-39 5/8 - - 11 . . • . . . 137-147 1-14 . . . 685-695
7/16 - 14 ’ ’ ’ . . . 46-50 5/8 - 18 . . . . . . 168-178
_______________
_______________—

NEW PARTS
♦WEAR
ENGINE PART (Standard Size)
LIMITS
MINIMUM MAXIMUM

CYLINDER BLOCK
Block Bore
Diameter—Cast Iron Block....................................................................... 4.6265"
Diameter—Aluminum Block ...................................................................... 4.6250"
Out of Round ............................................................................................ 4.6275"
4.6260"
Taper ....................................................................................................... .0030"
.0010"
Cylinder Liner Counterbore Diameter........................................................... .0020"
5.0460" .0010"
Depth—Cast Iron "High" Block..................................................................
Depth—Aluminum "High" Block ............................................................... .4785" .54
85" .2460" 5.0485"
Depth—Cast Iron and Aluminum "Low" Block .......................................... .4795"
Main Bearing Bore Inside Diameter............................................................. .5495"
3.8120"
Í2480"
Top Surface of Cylinder Block
Center Line of Crankshaft to Top of Cylinder Block 16.1840" 3.8130"
Distance................................................................................................
Flatness—Tranverse (3, 4 and 6 Cyl.)......................................................
Flatness—Longitudinally (3 Cyl.) ............................................................. 16.1890" 16.1760" Min.
Flatness—Longitudinally (4 Cyl.) ............................................................. .0030"
Flatness—Longitudinally (6 Cyl.) ............................................................. .0060"
.0070"
Depth of Counterbores (Top Surface) .0920" .10
.0090"
Cylinder Head Seal Strip Groove............................................................. 90" .0870"
Large Water Holes (Between Cylinders).................................................. .0870"
.1070"
J 200"
.0980"
4.6250" .0980"
CYLINDER LINERS Ì0005"
.0010" (Loose)
Clearance—Liner-to-Block Bore (Cast Iron Block)..................................... .0465"
.0020" 4.6260"
Clearance—Liner-to-Block Bore (Aluminum Block)....................................
.0025" .0030"
Depth of Liner Flange Below "High" Block.................................................
.0010" (Press) .0015" (Loose)
Height of Liner Flange Above "Low" Block ................................................ .0500" .0500"
Variation in Height Between Adjacent Liners.............................................. .0060" .0060"
.0020" .0020"
These clearances also apply to oversize or undersize parts.

Scanned with CamScanner