Catalogo Webcon Alpha

Components Manual - Edition 4.
Alpha Performance Parts

Alpha Engine Management System
Simplex 11-09-2001
Alpha Plus Engine Management System

Alpha Group - Standard Motor Products Europe Limited - Dolphin Road - Sunbury - Middlesex - England - TW16 7HE
Tel: +44 (0) 1932-788805 - Fax: +44 (0) 1932-789809 - E-mail: alpha@smpeurope.com - Internet: http://www.smpeurope.com
2
Disclaimer
DISCLAIMER
In view of our policy of continuous improvement, the

information in this guide is subject to change without
notice.
STANDARD MOTOR PRODUCTS EUROPE LTD SHALL NOT BE

LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR
OMISSIONS CONTAINED HEREIN; NOR FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE FURNISHING, PERFORMANCE,
OR USE OF THIS MATERIAL.
This guide contains information protected by copyright.

No part of this guide may be photocopied or reproduced
in any form without prior written consent from
STANDARD MOTOR PRODUCTS EUROPE LIMITED
All of the Alpha Performance kits are designed specifically for the
application as detailed, and should therefore do not require
further modification unless stated.
Any modifications made to components within the kits will invalidate
the warranty. Should any problems be encountered during installation,
please contact Standard Motor Products Europe Limited
or your authorised Alpha dealer.
Product names mentioned herein are for identification

purposes only and may be trademarks and/or registered
trademarksTM of their respective companies.
Standard Motor Products Europe Limited © 2001
3
Contents
2 DISCLAIMER
3 CONTENTS
6 ALPHA PLUS ELECTRONIC CONTROL UNITS
8 ALPHA PLUS 2 ELECTRONIC CONTROL UNITS
9 GOLD PERFORMANCE KITS (ALPHA PLUS ENGINE MANAGEMENT)
10 SILVER PERFORMANCE KITS (WEBER/ALPHA)
11 BRONZE PERFORMANCE KITS (ALPHA IGNITION MANAGEMENT)
12 WIRING HARNESSES
13 ELECTRICAL FITTINGS
15 MONO THROTTLE BODIES
16 INJECTOR MOUNTING ELBOWS
17 TWIN DCOE THROTTLE BODIES
19 TWIN DCNF THROTTLE BODIES
20 TWIN IDF THOTTLE BODIES
21 INLET MANIFOLDS
22 AIR FILTER FLANGE & INLET TUBES
23 AIR FILTER MOUNTING FLANGES
24 AIR HORN SELECTION
25 PERFORMANCE AIR FILTER SELECTION
26 THROTTLE LINKAGE - TOP MOUNTING
27 THOTTLE LINKAGE - BOTTOM MOUNTING
28 THOTTLE BODY ADJUSTMENT
29 LEVERS & GASKETS
30 POTENTIOMETER MOUNTING KITS (THROTTLE BODY)
31 POTENTIOMETER MOUNTING KITS (CARBURETTOR)
32 WEBER FUEL INJECTORS
33 PICO FUEL INJECTORS
34 WEBER INJECTOR MOUNTING KITS
35 PICO INJECTOR MOUNTING KITS
36 LOW PRESSURE FUEL PUMPS
37 HIGH PRESSURE FUEL PUMP
40 FUEL FILTER (METAL)
41 FUEL FILTER (PLASTIC)
42 FUEL FILTER/PUMP MOUNTING KIT
43 FUEL FILTER & FITTINGS
44 FUEL PRESSURE REGULATORS
46 IN-RAIL FUEL PRESSURE REGULATOR
47 MOTORSPORT FUEL PRESSURE REGULATOR
48 FUEL PRESSURE DAMPER
4
Contents
49 FUEL LINE HOSES & FITTINGS
50 PLASTIC HOSE CONNECTORS
51 INERTIA SWITCH
52 CD IGNITION PACK
53 IGNITION MODULES
54 IGNITION COIL & MODULE
55 IGNITION COIL
57 4 CYLINDER STATIC IGNITION COILS
59 PLUG TOP COILS
60 BALLAST RESISTOR
61 6 CYLINDER STATIC IGNITION COIL
62 SPARK PLUG LEADS
63 TEMPERATURE SEMSORS
64 STANDARD COOLANT TEMPERATURE SENSORS
65 AIR TEMPERATURE SENSORS
66 AIR PRESSURE SENSORS
68 SPEED SENSORS
69 CRANKSHAFT RPM TRIGGER DISCS
70 36-1 CRANKSHAFT RPM TRIGGER DISCS
71 SPECIFIC TRIGGER DISC KITS
72 COLD START AIR VALVE
73 COLD START AIR VALVE MOUNTING KIT
74 COLD START AIR MANIFOLDS
75 LAMBDA SENSOR & BOSS
76 ALPHA PUBLICITY MATERIAL
77 ALPHA PLUS & PLUS 2 CALIBRATION EQUIPMENT
78 ALPHA PLUS CALIBRATION EQUIPMENT
79 DEALER EQUIPMENT
81 LAMBDA DISPLAY SYSTEMS
82 RPM LIMITER
83 SEQUENTIAL GEAR SHIFT DISPLAY
84 GEAR SHIFT LIGHT KITS
85 CATALOGUES/BROCHURES
86 CUSTOMERS’ CARS
87 INDEX
5
Alpha Plus Electronic Control Units
6
GENERAL SPECIFICATION
Housing: Die-cast aluminium alloy casing complete with cast mounting lugs.
Location: Suitable only for the passenger compartment.
Connector: 35-way D-type with retention latch and seal.
Electronics: Microprocessor controlled digital unit with integral ignition amplifiers and original equipment engine
speed signal interface.
Functions: Controls ignition and injection with closed loop lambda fuel control and closed loop turbo
wastegate control.
Alpha Plus Electronic Control Units
7
ECU TECHNICAL CHARACTERISTICS
Nominal power supply: +12 Volts.
Range of power supply: +7 to 16 Volts.
Temperature range: -30˚ to +60˚ Centigrade.
Vibration general: 3g peak to peak.
Field Frequency 5 to 300Hz.
Humidity & water ingress: • Humidity below 90%, non-condensing.
• No direct water splash.
• No water entrapment within enclosure.
Injector drivers: 4
Ignition amplifiers: 2
Air valve driver: 1
Turbo wastegate drivers: 1
N.B. The turbo wastegate driver may be reconfigured as an extra ignition amplifier.
ORIGINAL EQUIPMENT RPM SIGNAL INTERFACES
The ECU PI043 is fitted with a micro controller device that is programmed to accept the correct
Original Equipment RPM signal pattern and engine configuration. The dealer must detail the O.E.
RPM signal pattern when ordering PI043 ECU’s.
The PI043 ECU part number requires a suffix code to identify the O.E. RPM signal pattern to be
programmed:
The first character specifies the O.E. RPM signal pattern:

B= Bosch 60-2
M= *Rover MEMS 36-1-1
E= Ford EECIV 36-1
R= *Renault Renix 44-2-2
G= *Weber IAW 60-2
K= *Rover 1.8 K Series Non-VVC
L= *Rover 1.8 K Series VVC
* Special Order Only - Please Contact Alpha Group.
The second character specifies the number of cylinders:

4= 4 Cylinders
6= 6 Cylinders
8= 8 Cylinders
e.g. A 6 cylinder engine with a Bosch 60-2 teeth signal pattern will require a PI043;B6 ECU.
The ECU PI0142 is fitted to engines that have been fitted with an Alpha trigger disc kit.
Part Number Product Description

PI042 ECU For Alpha Type Signal Frame
PI043 ECU For Original Equipment Signal Frame Interface
9990226100 Micro Controller
Alpha Plus 2 Electronic Control Units
8
TECHNICAL SPECIFICATION PI150
Ignition Control
• Drives up to two internal ignition amplifiers to cover all distributor and static ignition system types.
• 256 point calibration table (16 engine speed points against 16 load points).
• Air temperature correction.
• Engine rev limiter (soft and hard cut).
General
The ECU is supplied with a calibration to suit one of a range of engine types and specifications or
with a safe ignition base map. For non-standard specifications it needs to be programmed by an
approved Alpha Dealer for maximum benefit.
• Inbuilt tachometer output drive.
• Inbuilt gear shift indicator lamp drive (Gear Shift Lamp Kits. See Page 84)
• Direct 36-1 or 60-2 O.E. Signal input.
PI150 Alpha Ignition Only

Electronic Control Unit

PI150 Alpha Ignition Only Electronic Control Unit (ECU)
9990297900 PI150 Retaining Bracket
Gold Performance Kits (Alpha Plus Engine Management)
9
These Gold Performance Kits release the performance potential of production Ford, Renault, VW,
Vauxhall/Opel & Peugeot/Citroën engines. A complete kit covers both fuel injection and
distributorless ignition requirements in a fully integrated package. The kits are supplied with a
lambda sensor and can operate with exhaust catalytic convertors. The kits are calibrated for a
standard specification engine. For non-standard engines please contact us.
Each kit includes:

• 2 x ALPHA throttle bodies.
• Perfomance air filters.
• Throttle linkage system.
• Inlet manifold & fitting kit.
• ALPHA PLUS engine management system.
• Fitting instructions & setting procedure.
Typical Power Figures
Ford Zetec 2.0 16v Std 128 bhp (95kW)

Alpha 165 bhp (123kW)
Renault Clio 1.8 16v Std 137 bhp (102kW)

(@ Flywheel) Alpha 155 bhp (116kW)
Renault Clio Sport 172 2.0 16v Std 165 bhp (123kW)
Vauxhall Ecotec 2.0 16v Std 132 bhp (98kW)

(Fast Road Cams) Alpha 171 bhp (128kW)
Vauxhall XE 2.0 16v Std 150 bhp (112kW)

VW 1.8 16v Std 139 bhp (104kW)

Peugeot/Citroën 1.9 8v Std 128 bhp (96kW)

(205 GTi) Alpha 170 bhp (127kW)

K98003 General Alpha Plus 4 Cylinder Engine Management Kit
K99010 Alpha Plus Engine Management Kit - Ford Zetec 1.8 16v
K99011 Alpha Plus Engine Management Kit - Ford Zetec 2.0 16v
K99012 Alpha Plus Engine Management Kit - Vauxhall/Opel XE 2.0 16v (Distributor)
K99013 Alpha Plus Engine Management Kit - Vauxhall/Opel XE 2.0 16v (Static)
K99016 Alpha Plus Engine Management Kit - Vauxhall Ecotec 2.0 16v
K99018 Alpha Plus Engine Management Kit - Peugeot/Citroën (XU9) 1.9 8v (Static)
K99019 Alpha Plus Engine Management Kit - Ford Kent 1.7 8v (Static)
K20002 Alpha Plus Engine Management Kit - VW 1.8 16v (Static)
K20003 Alpha Plus Engine Management Kit - Renault Clio/19 1.8 16v (Distributor)
K20013 Alpha Plus Engine Management Kit - Renault Clio Sport 172 2.0 16v (Static)*
* Contact Alpha Group For Availability.
10
Silver Performance Kits (Weber/Alpha)
These Silver Performance Kits are a combination of the legendary WEBER DCOE carburettor and
the hi-tech ALPHA Ignition Management System. This proven combination releases the
performance potential of production engines from Ford, Vauxhall/Opel & Peugeot/Citroën. The
Vauxhall/Opel kits have been developed from knowledge gained developing the “Super Touring”
car race engines. They are complete kits that cover both fuelling and ignition requirements in a fully
integrated package. The kits are calibrated for standard specification engine. For non-standard
engines please contact us.
Each kit includes:

• 2 x WEBER DCOE sidedraught carburettors.
• Performance air filters.
• Throttle linkage system.
• Inlet manifold & fitting kit.
• ALPHA 3D ignition system.
• Throttle position sensor.
• Fitting instructions & setting procedure.
Typical Power Figures
Ford Zetec 2.0 16v Std 128 bhp (95kW)

Vauxhall XE 2.0 16v Std 150 bhp (112kW)

Peugeot/Citroën 1.9 8v Std 128 bhp (96kW)

(205 GTi) Alpha 170 bhp (127kW)

K99001 Weber/Alpha Performance Kit - Ford Zetec 1.8 16v
(45 DCOE)
(45 DCOE)
K99004 Weber/Alpha Performance Kit - Vauxhall/Opel XE 2.0 16v
(45 DCOE/Distributor)
K99005 Weber/Alpha Performance Kit - Vauxhall/Opel XE 2.0 16v
(45 DCOE/Static)
(40 DCOE & Small Air Filters)
(40 DCOE)
K99008 Weber/Alpha Performance Kit - Peugeot/Citroën XU9 1.9 8v
K99009 Weber/Alpha Performance Kit - Peugeot/Citroën XU9 1.9 8v
(40 DCOE/Static)
K99020 Weber/Alpha Performance Kit - Ford Pinto 2.0 8v
K99021 Weber/Alpha Performance Kit - Ford Pinto 2.0 8v
(45 DCOE/Static)
Bronze Performance Kits (Alpha Ignition Management)
11
A 2D electronic ignition system featuring an ignition map of 16 RPM sites that can be upgraded to
full 3D ignition management by the addition of a throttle position sensor (16 RPM x 16 engine load
points)
SYSTEM FEATURES
Each PI150 Ignition Only ECU has the following features:
• 2D ignition timing giving 16 ignition advance values located at 16 variable engine speed sites.
• Option of 3D ignition timing giving 256 ignition values at 16 variable engine load sites for each
of the 16 engine speeds sites.
• Linear interpolation between engine speed and load sites for smooth transition of ignition
advance values.
• Correction to ignition advance values for inlet air temperature.
• Engine speed limiter via ignition cut.
• Tachometer and gearshift indicator lamp drives.
• 1 or 2 ignition outputs for distributor or static ignition.
• Direct 36-1 or 60-2 engine speed trigger inputs.
Each kit contains every part needed to install and run the ignition system. This includes PI150
ECU, ignition coil (except K97014), specific wiring harness, air temperature sensor & cable ties.
For engine applications where the original equipment ignition coil and/or crank trigger system can
not be used, the kit will include some or all of the following:
• Relevant ignition coil.
• Trigger disc kit.
• Ignition lead set.
• Coil mounting bracket.
• Engine speed sensor.
All of the kits below can be upgraded to full 3D ignition timing by the addition of a Throttle Position Sensor,
See Page 31. All general Alpha ignition management systems are supplied with a safe base ignition map,
ideal for checking correct installation. Engine spacific systems are supplied with a calibration for a standard
specification engine. General systems must be calibrated by on of the “Alpha System Dealers” to obtain the
maximum benefit from programmed ignition timing.

K97013 General Ignition Only Kit (Distributor)
K97014 General Ignition Only Kit (Static)
K97015 Ignition Only Kit - Ford Kent 1.7 8v (Distributor)*
K97016 Ignition Only Kit - Ford Kent 1.7 8v (Static)*
K97017 Ignition Only Kit - Ford Zetec 1.8 16v & 2.0 16v
K97018 Ignition Only Kit - Vauxhall/Opel XE 2.0 16v (Distributor)
K97019 Ignition Only Kit - Vauxhall/Opel XE 2.0 16v (Static)
K97025 Ignition Only Kit - Peugeot/Citroën XU9 1.9 8v (Distributor)*
K97026 Ignition Only Kit - Peugeot/Citroën XU9 1.9 8v (Static)*
K97027 Ignition Only Kit - Ford Pinto 2.0 8v (Distributor)*
K97028 Ignition Only Kit - Ford Pinto 2.0 8v (Static)*
* Also include all necessary trigger disk kits and component brackets.
12
Wiring Harnesses
Part Number: 9990287100
Wiring harnesses especially designed for the range of Alpha engine management systems. The
harness supplements the vehicles existing wiring harness.
Part Number ECU Type Product Description

9990180500 Ignition Only Ignition Only Harness, Feed Harness
9990224800 Alpha Plus General 6 Cylinder Static Harness
9990225000 Alpha Plus Porsche 911 6 Cylinder Harness
9990225400 Alpha Plus General 8 Cylinder Harness
9990272400 Ignition Only Ford Zetec Static Harness
9990272500 Ignition Only Vauxhall/Opel XE Static Harness
9990272600 Ignition Only Vauxhall/Opel XE Distributor Harness
9990283900 Ignition Only General 4 Cylinder Static Harness
9990287100 Alpha Plus General 4 Cylinder Static Engine Harness (Race)
9990287200 Alpha Plus General 4 Cylinder Static Vehicle Harness (Race)
9990290000 Alpha Plus V8 Distributor Harness
9990293500 Alpha Plus A-Series Two Injector Static Harness
9990298200 Alpha Plus Kit Car Harness 4 Cylinder (Ford Zetec 1.8 & 2.0 Only)
9990298300 Alpha Plus General 4 Cylinder Harness (Replaces 9990205300)
Electrical Fittings
13
9990098900 Female Minitimer Connector Pin 0.5-1.5mm Wire
9990204700 Female Minitimer Terminal Pin (High Spec.) 0.5-1.0mm Wire
9990204800 Female Minitimer Terminal Pin (High Spec.) 1.0-2.5mm Wire
9990166400 Female Minitimer Connector 2-Pin Black
9990166500 Female Minitimer Connector 2-Pin White
9990166600 Female Minitimer Connector 2-Pin Blue
9990166700 Female Minitimer Connector 2-Pin Brown
9990166800 Female Minitimer Connector 2-Pin Grey
9990201500 Female Minitimer Connector 2-Pin Green
9990284400 Male Minitimer Connector 3-Pin Black
9990157900 Rubber Boot 2-Pin Female Minitimer Connector - 90˚
9990175600 Rubber Boot 2-Pin Female Minitimer Connector
Electrical Fittings
14
9990126900 Relay
9990179400 Relay Holder
9990152500 Packard Connector 2-Way (BAE800AK Coil & ATS05)
9990152600 Terminal Pin For Connector 9990152500
9990206900 Fuse Holder (Supplied With Terminals)
9990127000 10 Amp Blade Fuse
9990127100 15 Amp Blade Fuse
9990137400 Mountable Cable Tie
9990180600 Inertia Switch Connector - Early ‘Pop Up’ Button Type
9990180700 Inertia Switch Terminal - Early ‘Pop Up’ Button Type
9990181200 Connector 6-Pin White - CD Pack
9990181300 Terminal Pin For Connector 9990181200
9990221600 Wiring Harness Grommet 45mm To 50mm Hole
9990230300 Male Minitimer Connector 2-Pin Black
9990230400 Terminal Pin For Connector 9990230300 & 9990284400
9990241600 Connector Ford 3-Pin Static Ignition Coil
9990241700 Terminal Pins 1 & 3 For Connector 9990241600
9990241800 Terminal Pin 2 For Connector 9990241600
9990241900 Seal For Terminals 9990241700 & 9990241800
9990208300 3-Pin Female Inertia Switch Connector Kit
9990206500 Terminals For Connector 9990206600
9990206600 Female Lambda Sensor Connector (9990205300 Harness)
9990206700 Spacer For 9990206600
9990181800 Sureseal Male Pin
9990181900 Sureseal Female Pin
9990182100 Sureseal Recepticle Housing
Mono Throttle Bodies
15
Illustrated: 40mm right hand potentiometer 9990121400
Supplied with a quadrant type throttle lever (not shown)
Material: Aluminium alloy LM25.
Finish: Hard wearing black crinkle powder coating. Part Number: 9990121400
Shaft support: Two SKF single groove ball race bearings.
Shaft drive: Weber 5 x 7mm double ‘d’ drives.
Bore size: 40mm and 45mm.
Mounting: Standard DCOE/DHLA carburettor type flange.
Air horns: Standard DCOE/DHLA airfilter mounting flange.
Potentiometer: High resolution logarithmic type fitted to potentiometer throttle bodies.

9990121400 40mm Right Hand Potentiometer
9990121500 40mm Right Hand Slave
9990121600 40mm Left Hand Potentiometer
9990121700 40mm Left Hand Slave
Injector Mounting Elbows
16
Slotted mounting holes
Right Hand Elbow 9990122800 (Not Available) for simple alignment
shown fitted with an injector and mounting kit.
Illustrated: Left Hand Elbow 9990122900.
Material: Aluminium alloy.
Finish: Hard wearing black crinkle powder coating.
Injectors: Accepts standard 14mm ‘O’ ring injector fittings.
N.B. Uses Injector Mounting Kits listed on pages 34 and 35 to fit injectors.
Suitable for use with Webcon UK ‘Mono Throttle Bodies’ listed on page 15.

9990122900 Left Hand Elbow With Injector Port
Twin DCOE Throttle Bodies
17
Illustration: 40mm Right Hand
Potentiometer 9990120300.
Fuel connection cam be

rotated through 360˚ to provide
the best installaion position
45mm Left Hand

GENERAL SPECIFICATION Potentiometer
9990120600
Material: Aluminium alloy LM25.
Finish: Hard wearing black crinkle powder coating.
Shaft support: Two SKF single groove ball race bearings.
Shaft drive: Weber 5 x 7mm double ‘D’ drives.
Bore sizes: 40, 45, 48, and 50mm diameter.
Air horns: Air inlet hose fitting for maximum tuning and installation flexibility.
Potentiometer: High resolution logarithmic type fitted to potentiometer throttle bodies.
Injectors: Accepts standard 14mm ‘O’ ring injector fitting.
N.B. 2 injector mounting kits required per twin throttle body.
Twin DCOE Thottle Bodies
18
EXAMPLE OF TYPE AND PART NUMBERING
40mm LH Slave 40mm RH Pot.

9990120000 9990120300
Type Identification From This Side

N.B. LHP bodies are fitted with PF3B Potentiometers, RHP bodies are fitted with PF4B
Potentiometers.
Twin DCNF Throttle Bodies
19
These twin DCNF throttle bodies are based upon the DCNF carburettor and mounting flange
(shown above) and are available in two bore sizes: 40mm and 42mm. This range of throttle bodies
offer the benefit of simpler engine management conversions on engine previously fitted with
downdraught DCNF carburettors and manifolds.
There are two styles of the DCNF throttle body, the first is suited for straight engine configurations,
while the second is designed for narrow ‘V’ engines and feature a smaller overall width allowing
the injectors and fuel rail to be mounted in-board of the engine ‘V’. This second style has the suffix
S on the part numbers.
The bodies are supplied with fuel rails that mount the injectors in position, throttle levers (male and
female) and a single D shaft drive for a throttle position sensor.

V80450LS 40mm Left Hand Slave
V80450RS 40mm Right Hand Slave
V80452LS 42mm Left Hand Slave
V80452RS 42mm Right Hand Slave
V804540L 40mm Left Hand Potentiometer
V804540R 40mm Right Hand Potentiometer
V804542L 42mm Left Hand Potentiometer
V804542R 42mm Right Hand Potentiometer
Twin IDF Thottle Bodies
20
These twin IDF throttle bodies are based upon the IDF carburettor and mounting flange (shown
above) and are available in two bore sizes: 40mm and 45mm. This range of throttle bodies offer
the benefit of simpler engine management conversions on engines previously fitted with down
draught IDF carburettors and manifolds.
The bodies are supplied with air horns, fuel rails that mount the injectors in position, throttle levers
(male and female) and a single D shaft drive for a throttle.

V804440PL 40mm Left Hand Potentiometer
V804440L2 40mm Left Hand Slave
V804440PR 40mm Right Hand Potentiometer
V804440R2 40mm Right Hand Slave
V804445PL 45mm Left Hand Potentiometer
V804445L2 45mm Left Hand Slave
V804445PR 45mm Right Hand Potentiometer
V804445R2 45mm Right Hand Slave
Inlet Manifolds
21
Peugeot 205 1.9 8v
Inlet Manifold
Zetec 2.0 16v

Inlet Manifold
Material: Cast Aluminium alloy.
Flange: Standard Weber DCOE side draught bolt pattern, which fits both DCOE and throttle body
requirements.
Fitting: All manifolds come with the necessary steel fitting studs.
Choke Side/ Carburettor/

Part Engine Size Down Throttle Body
Number Type (mm) Draught Type
MM4242B Ford CVH 8v 45 Side DCOE
MM44240A Ford X-Flow 8v 40 Side DCOE
MM4270B Ford Pinto 8v 45 Side DCOE
MM5000 Ford Zetec 1.6,1.8,2.0 16v, Short 45 Side DCOE
MM42806B Ford Zetec 1.6,1.8,2.0 16v, Long 45 Side DCOE
MM5100 Vauxhall XE 2.0 16v 45 Side DCOE
MM5200 Vauxhall Ecotec 2.0 16v 45 Side DCOE
MM5600 Vauxhall Ecotec 1.6 16v 40 Side DCOE
MM5700 Vauxhall Ecotec 1.6 16v (7°) 40 Side DCOE
MM5400 Rover K-Series 16v 40/45 Side DCOE
MM4980A Peugeot/Citroën XU9 1.9 8v 40 Side DCOE
MM4980B Peugeot/Citroën XU9 1.9 8v 45 Side DCOE
MM5300 VW Golf 1.8/2.0 16v, Short 45 Side DCOE
MM5500 VW Golf 1.8/2.0 16v, Long 45 Side DCOE
Air Filter Flange & Inlet Tubes
22
Material: Aluminium alloy.
Flange: Standard Weber side draught DCOEair filter fitting.
Installation: Accepts 50mm ID hose.

9990100400 Twin Bore Air Filter Flange - 40mm and 45mm
9990235400 Twin Bore Air Filter Flange - 48mm
9990121800 Single Air Horn / Inlet Air Hose Adaptor
Part Number Throttle Body Fitting Air Intake Tube Hose Dimns
9990252700 40mm & 45mm 50mm I/D - 60mm O/D - Straight 0.5m
9990188900 48mm & 50mm 57mm I/D - 67mm O/D - Straight 0.5m
Air Filter Mounting Flanges
23
A clamp-on assembly for use on ALPHA twin throttle bodies (40mm & 45 mm). Converts to a
standard DCOE style air filter mounting flange. An aluminium casting finished in black crinkle to
match the throttle bodies.
Kit contents:
• 2 x Air filter flanges.
• 4 x M6 studs.
• 4 x Locating tabs.
• 4 x M6 Nyloc nuts.
• Throttle body and air filter flange (25mm) assembly height 110mm.
• Throttle body and air filter flange (13mm) assembly height 98mm.
• DCOE carburettor height 118mm.

9990261500 Air Filter Mounting Flange Kit (25mm)
9990298800 Air Filter Mounting Flange Kit (13mm)
Air Horn Selection
24
Carburettors/Throttle Bodies will require air horns weather air filters are fitted or not. Air horns
smooth the flow of air entering, which reduces turbulence therefore improving performance and
response.
Construction: Either a spun Steel or Aluminium construction which is bolted to the main casting.
Length I/D O/D

Part Number Application (mm) (mm) (mm)
AH801 40 DCOE 16 40 58
AH802 40 DCOE 26 40 57
5284001200 40 DCOE 39 40 58
AH813 45 DCOE 16 45 70
AH814 45 DCOE 26 45 70
AH815 45 DCOE 39 45 70
AH841* 40mm & 45mm T/Bodies 40 45 70
AH851** 40mm & 45mm T/Bodies 52 45 70
5284000101 45 DCOE 62 50 64
5284003400 48 DCO/SP 95 52 65
5284003300 48 DCOE & T/Bodies 56.5 53 70
* To be used with Air Filter Mounting Kit Part No. 9990261500

** To be used with Air Filter Mounting Kit Part No. 9990298800
25
Performance Air Filter Selection
The performance air filters that are supplied as part of the Alpha performance kits are cotton with
wire mesh sandwich type filter element. All performance air filters and bases are compatible with
the Weber performance carburettor and throttle body range.
Each kit includes a polished stainless steel base and cover, a mounting gasket and cleaning
instructions. Kit JRW516/ATS has an air temperature sensor fitted as standard which is utilised by
the carburettor performance kits and full engine management kits. All performance air filters are
washable therefore ensuring a long life.
A wide range of performance filters for many types of vehicles are stocked, please phone for
details of availability and price.
Product Filter
Part Number Description Depth (mm) Colour
JRW514 Air Filter 50 Blue
JRW516/ATS Air Filter 90 Blue
CR-05203 Conical Air Filter 7 Blue
CR-01601 Oil Breather 38 Blue
1006 Oil & Cleaner (300cc & 500cc) N/A N/A
Throttle Linkage - Top Mounting
26
Alpha throttle body top
mounting linkage
Alpha Throttle Body Top Mounting Linkage

Utilising the existing DCOE throttle linkage kits LP1000 and LP2000, this linkage assembly
requires the fitment of the mounting lever 9990172100. LP linkages are supplied complete with full
fitting instructions and accessories.
NOTE:- When using Pico Injectors, a Pico Clearance Kit will be needed to enable the linkage to function
correctly.
Construction: • Mild steel plate protected with zinc and yellow passivate plating.
• Twin return springs.
• Adjustable over centre throttle stop.
• Twin sintered bronze self-lubricating quadrant bearings.
• High quality 8mm steel ball joints.
• Supplied with low friction teflon coated cables.
• Inner cable connects to quadrant cam for smooth linear action.
• Adjustable throttle cable movement - 22mm to 40mm.
Fitting: • Mounts directly to one Webcon Alpha twin throttle body. Suitable for both left and right hand
throttle bodies.

LP 1000 Single Cable - DCOE (For Use With Existing Cable)
LP 2000 Twin Cable - DCOE (Cables Included)
9990172100 Top Mounting Bracket
9990298700 Pico Injector Clearance Kit
Thottle Linkage - Bottom Mounting
27
Alpha Throttle Body Underside Mounting Linkage
The LP 7000 linkage kit is supplied complete with full fitting instructions and accesories.
Construction: • Mild steel plate protected with zinc and yellow passivate plating.
• Twin return springs.
• Adjustable over centre throttle stop.
• Twin sintered bronze self-lubricating quadrant bearings.
• High quality 8mm steel ball joints.
• Supplied with two low friction teflon coated cables.
• Inner cable connects to quadrant cam for smooth linear action.
• Adjustable throttle cable movement - 22mm to 40mm.
Fitting: • Mounts directly to one throttle body.
• 40, 45, 48 and 50mm Webcon Alpha twin throttle bodies. Suitable for left or right hand throttle
bodies.

LP 3000 Single Cable - DCOE (For Use With Existing Cable)
LP 4000 Twin Cable - DCOE (Cables Included)
LP 7000 Twin Cable - Throttle Bodies (Cables Included)
Thottle Body Adjustment
28
Twin throttle body cover plate with integral return spring anchor
This part will fit all Alpha DCOE style throttle bodies and will reduce the return spring tension by
approximately 30%.

9990192700 Cover Plate With Return Spring Adaptor
29
Levers & Gaskets
THROTTLE LEVERS
Part Number Product Description Type

9990123300 Twin Throttle Body Lever Male
9990123400 Mono Throttle Body Lever Male
4504814900 Mono/Twin Throttle Body Lever Female
GASKETS

9990124400 40mm Flange Gasket
Potentiometer Mounting Kits (Throttle Body)
30
Logarithmic Throttle Potentiometer And Mounting Kit
Shaft Rotation: •Type PF3B - clockwise. (Part Number WTP023).

•Type PF4B - anticlockwise. (Part Number WTP069).
Shaft drive: Requires 4mm double ‘D’ drive.
Resistance: 550 Ohm.
Each kit includes:

• High resolution potentiometer.
• Mounting casting.
• Adjusting bracket.
• ‘O’ ring seal.
• Mounting screws and washers.
• Fitting instructions.
Wiring details for Alpha System harness:

• Pin 1 Ground Blue
• Pin 2 Signal Purple / Blue
• Pin 3 5V Ref. Green / Red
N.B. Use service tool 9990140400 to set potentiometers in the correct position.
Part Number Product Description Shaft Rotation

9990149900 Potentiometer PF3B & Mounting Kit Clockwise
9990150000 Potentiometer PF4B & Mounting Kit Anti-clockwise
Potentiometer Mounting Kits (Carburettor)
31
40/45 DCOE Throttle Position 48 DCO SP Throttle Position
Sensor Mounting Kit. Sensor Mounting Kit.
Throttle Position Sensor kits for Weber sidedraught carburettors
Quick and easy to fit, no machining required, fitting instructions included.

These kits include:
• Throttle position sensor.
• Mounting bracket and fittings.
• Throttle lever.
Suitable for fitment to 40/45 DCOE, 48 DCO SP and Dellorto 40/45 DHLA in conjunction with the
ignition mangement systems detailed on pages and to complete 3D ignition mapping for both
distributor and distributorless ignition systems.
Wiring details for Alpha System harness:

• Pin 1 Signal Purple / Blue
• Pin 2 Ground Blue
• Pin 3 5V Ref. Green / Red

9990266000 TPS Mounting Kit 40/45 DCOE
9990266800 TPS Mounting Kit 48 DCO SP
9990290200 TPS Mounting Kit 40/45 DHLA
Weber Fuel Injectors
32
Type: Electromagnetic petrol injector, calibrated orifice type.
Construction: Fully sealed unit.
Electrical: Standard 2-pin Minitimer connector.
Weight: 100 grams.
Sealing ‘O’ ring, 14mm O.D. is available separately. Part Number 4156504700.
N.B. Matched sets of Injectors are available to special order.
Part Product DC Static Flow

Number Description Type Colour Resistance (3 Bar)
WFI005 Injector IW052 Brown 14.5 Ohms 149 cc/min
WFI192 Injector IW042 Red 16.2 Ohms 190 cc/min
WFI191 Injector IW031 Green 16.2 Ohms 270 cc/min
WFI193 Injector IW058U Biege 14.5 Ohms 384 cc/min
Pico Fuel Injectors
33
Type: Electromagnetic petrol injector, calibrated orifice type.
Construction: Fully sealed unit standard 14mm ‘O’ ring fitting.
Electrical: Standard 2-pin Minitimer connector.
Weight: 40 grams.
Sealing ‘O’ ring, 14mm O/D is available separately, Part Number 4156504700.
N.B. Matched sets of Injectors are available to special order.
Part Product DC Static Flow

Number Description Type Nozzle Resistance (3 Bar)
WFI023 Injector IWP023 1 Jet 14.5 Ohms 159 cc/min
Weber Injector Mounting Kits
34
Allen Screw &
Plastic Moulding Spring Washer
Collets
Clamp Plate
Circlip
Rubber Seating
Union
Double Fuel Union
Injector reatining clip for use

with cup type coupling on rigid
fuel rails
Single Fuel Union
To mount Weber type ‘O’ ring fitting injectors to Alpha twin throttle bodies and injector mounting
elbows.
Fuel union kits contains:

• 1 x Union.
• 2 x Collets.
• 1 x Circlip.
N.B. Injector is not included with the mounting kit.

Injector retaining clip for use with cup type fittings on rigid fuel rails, Part Number 4761501101.
An injector cup, suitable for screwing into a solid fuel rail, is available. Part number 9990259400.

9990122300 Injector Mounting Kit (Double)
9990148900 Injector Mounting Kit (Single)
9990178900 Injector Fuel Union Kit (Double)
9990226000 Injector Fuel Union Kit (Single)
9990001200 13mm Fuel Hose Clip
4761501101 Injector Retaining Clip
9990259400 Injector Mounting Cup
Pico Injector Mounting Kits
35
Mounting Bracket Kit 9990268600
Single Fuel Union Double Fuel Union
Pico Injector Mounting Kits
A mounting kit to fit a Pico fuel injector onto the Webcon twin throttle bodies and injector mounting
elbows.
Each kit contains:

• 1 x Mounting bracket.
• 2 x Insulation washers.
• 2 x Mounting screws.
• 2 x Collet.
• 1 x Circlip.
• 1 x Fuel union (single or double).

9990268500 Pico Injector Mounting Kit (Single Fuel Union)
9990268600 Pico Injector Mounting Kit (Double Fuel Union)
9990298700 Pico Injector Clearance Kit
Low Pressure Fuel Pumps
36
Construction: Fully sealed unit, steel casing, zinc plated and yellow pasivated.
Connections: Accepts ‘Push-On’ fuel pipe at both ends, 8mm O/D at inlet and outlet.
Electrical: Suitable for 12 volt operation, fitting supplied.
Dimensions: Length 172mm x Ø54mm.
Supplied with the following parts:

• Mounting bracket.
• 2 x 100mm lengths of fuel line.
• Hose clips and unions.
Part Product Flow Range Pressure Range

Number Description (L/Hr) (Bar)
WFP501 Electric Fuel Pump 90 - 130 0.34 - 0.62
WFP502 Electric Fuel Pump 90 - 130 0.17 - 0.31
High Pressure Fuel Pump
37
Construction: Fully sealed unit, aluminium alloy casing with plastic end moulding at outlet.
Connections: Accepts ‘push -on’ fuel pipe at both ends, 12mm O/D at inlet 8mm O/D at outlet.
Electrical: Suitable for 12 volt operation, fitting supplied.
Mounting: Unit must be gravity fed under all conditions.
Fuel inlet must be protected by 50 micron in tank (not in-line type).
Part Number Product Description Output (Li/Hr@ 3 Bar)

WFP700 Electric Fuel Pump 100
38
Construction: Fully sealed unit, aluminium alloy casing with plastic end moulding.
Connections: Outlet 9/16 x 18 UNF male, Inlet M16 x 1.5 female.
Electrical: Suitable for 12 volt operation, accepts standard automotive connectors.
Mounting: Unit must be gravity fed under all conditions.
Fuel inlet must be protected by 50 micron in tank (not in-line type).

39
A roller vane type electric fuel pump for use on high flow and high pressure installations. This pump
is supplied complete with two wrap around cushioned mounting brackets and four bolts for quiet
operation.
Connections: Accepts ‘Push-On’ 9.5mm I/D fuel pipe at both ends.

Electrical: Suitable for 12 volt operation.
Dimensions: Length 200mm x Ø48mm

Fuel Filter (Metal)
40
Construction: Fully sealed unit with lightweight aluminium alloy casing for use as a pre-injector filter.
Filtration: Highly efficient filter medium removes microscopic particles down to 10 microns to avoid
contamination of fuel injectors.
Dimensions: Length 130mm x diameter 55mm.(WFF042)
Length 130mm x Ø58mm.(WFF213)
Both units are interchangeable
Connections: Inlet M14 x 1.5 male.
Outlet M12 x 1.5 male.

WFF042 Fuel Filter (55mm O/D)
WFF213 Fuel Filter (58mm O/D)
9990138900 Ø8 Push-On Hose Connector (M14 x 1.5)
9990173800 14mm Dowty Washer
9990139100 Ø8 Push-On Hose Connector Banjo (12mm)
9990139200 M12 x 1.5 Banjo Bolt
9990224200 12mm Dowty Washer
9990191000 Ø8 Push-on Hose Connector Banjo (14mm)
Fuel Filter (Plastic)
41
Construction: A fully sealed fuel filter in black glass reinforced plastic for use as a pre-injector filter.
Connections: Two 8mm Push-on fuel hose connections.
Dimensions: Length 150mm (inc. connections) x 57mm main diameter.
Unit fits into the fuel filter mounting kit 9990159400.

WFF214 Fuel Filter (Plastic)
Fuel Filter/Pump Mounting Kit
42
Fits Alpha system fuel filters WFF213 and WFF214.

Kit supplied with all fittings and a self-adhesive insulation strip for mounting fuel pump WFP700.
Rubber mounted bracket finished in zinc and yellow passivate.

9990159400 Fuel Filter/Pump Mounting Kit
Fuel Filter & Fittings
43
9990130200 9990130300
9990130400 9990154700
9990154700

9990130200 Union Ø 8 x 12mm - Plated Mild Steel - 43mm Long
9990130300 Union Ø 8 x 12mm - Plated Mild Steel -28mm Long
9990130400 40 Micron In-tank Fuel Filter
9990154700 Union & In-tank Filter Assembly
44
Fuel Pressure Regulators
Type RP9, RP12 & RP42 Type RP1, RP7, RP8, RP19
& RP22
Type RP17
Construction: Die-cast aluminium alloy sealed unit.

Mounting: Threaded mounting holes in casing.
Flow
Part Product Rate
Number Description Type (Li/Hr) Fittings
WFR050 2.5 Bar Regulator RP7 60 2 x 8mm Push-on
WFR052 3.0 Bar Regulator RP9 60 1 x 14mm ‘O’ Ring
& 1 x 8mm Push-on
& 1 x 8mm Push-on
& 1 x 8mm Push-on
& 1 x 8mm Push-on
& 1 x 6mm Push-on
45
Fuel Pressure Regulator

Connections: 2 x M16 x 1.5 threaded fittings, high pressure side.
1 x 8.0mm push on hose fitting, low pressure fuel return.
Flow
Part Number Product Description Type Rate (Li/Hr) Fittings
WFR034 2.5 Bar Regulator RP54 100 Threaded
Inlet
Connections
In-rail Fuel Pressure Regulator
46
Construction: Stainless steel body and cover. Fabric-reinforced vulcanized-rubber elastic membrane, methanol
resistant. Internal parts in contact with fuel are in stainless steel.
Mounting: Mounted in fuel rail with 20mm ‘O’ ring.
Connections: 4mm push-on connection and 5mm ‘O’ ring.
Fuel: Commercial and F1.
Part Number Product Description Type Flow Rate (Li/Hr)

WFR048 2.5 Bar Regulator RPM36 40
Motorsport Fuel Pressure Regulator
47
Specifically designed for motorsport applications up to and including Formula One, these
regulators are manufactered from Ergal and weigh just 99 grams.
Construction: Ergal body and cover. Valve and seat made from martenistic stainless steel.
Height: 56.9mm Max.
Diameter: 47.5mm Max.
Fuel: Commercial and F1.
Part Number Product Description Type Flow Rate (Li/Hr)

WFR500 6.0 Bar Regulator RPF22/01 25 - 700
WFR501 10.0 Bar Regulator RPF17/04 25 - 700
48
Fuel Pressure Damper

Connections: 2 x 8.0mm push on hose fittings.
Range: 1.7 to 4.0 bar.

WFD001 Fuel Pressure Damper SP01
Fuel Line Hoses & Fittings
49
Fuel Line Hose
A high quality fuel line hose suitable for use with leaded and unleaded fuels on carburettor and
injection system installations. This hose is available in three sizes and supplied in 10 metre reels.
Material: Nitrile Butadiene rubber liner.

Construction: NBR liner with synthetic textile reinforcement and an oil and weather resistant cover.
Working Pressure: 4 bar (58 psi).
Burst Pressure: 12 bar (175 psi).
Temperature Range: -35˚ to 100˚ Celsius.
Product I/D O/D Hose Clip

Part Number Description (mm) (mm) Part Number
9990268700 Fuel Line Hose 5.8 12.0 9990009100
9990268800 Fuel Line Hose 7.4 13.5 9990001200
9990268900 Fuel Line Hose 9.5 15.5 9990008100
Part Number Product Description Dimns. (mm)

9990273600 Fuel Line Hose 1m Length 7.4 I/D
9990009400 Hose Clip 14
9990141600 180˚ Shaped Hose 10
9990141700 Herbie ‘G’ Clip 17 - 19
9990273700 Cobra Clip N/A
9990274100 Cobra Clip Pliers N/A
N.B. 180˚ Hose (Part Number 9990141600) is suitable for fuel pump inlet.
50
Plastic Hose Connectors
9990041100 Plastic ‘Y’ Connector Ø4
9990089700 Plastic ‘Y’ Connector Ø6 - Ø8 - Ø6
9990070700 Plastic ‘T’ Connector Ø6
9990097000 Plastic ‘T’ Connector Ø8 - Ø6 - Ø8
9990045000 Plastic Elbow Connector Ø19
9990052200 Plastic Hose Connector Ø8 - Ø6
9990083500 Plastic Hose Connector Ø12 - Ø8
9990087600 Plastic Hose Connector Ø8
9990125500 Plastic Hose Connector Ø8 - M12 x 1.5
9990125700 Plastic Hose Connector Ø8 - M14 x 1.5
9990125600 Plastic Elbow Connector Ø8 - M12 x 1.5
9990125800 Plastic Elbow Connector Ø8 - M14 x 1.5
Inertia Switch
51
The inertia switch detects the deceleration of a motor vehicle when impacted in any
direction.Designed to be immune to normal vehicle ride shocks and surface vibrations.
The switch will operate at 12g peak, 0.06 secs and will not operate at 6g peak, 0.06 secs.
Must be installed as directed on the instructions supplied only for use in deactivating the fuel pump
in the event of an accident (safety related device).
Original equipment fitment by Rover with TUV (Germany) approval.
Suitable for under bonnet fitment provided the switch is free from the risk of spillage of liquids or
direct water spray.
N.B. 9990208300 connector conversion kit enables wiring harnesses with connectors for inertia
switch 9990135000 to use inertia switch 9990205700.

9990205700 Inertia Switch
9990208300 Inertia Switch Connector Conversion Kit
CD Ignition Pack
52
WARNING
This unit produces very high voltages.
General Specification
This is a HIGH VOLTAGE capacitive discharge unit that is compatible for use with the Alpha
system. The CD unit replaces the ignition amplifier module.
The kit includes:

• C.D. Module.
• Standard automotive 6 way connector.
This module must be flexibly mounted by the installer.

The aluminium casting is black anodized finished.

9990166200 CD Ignition Kit
Ignition Modules
53
An ignition module mounted on a die cast alloy heat sink.

WIM081 Ignition Module
WIM082 BKL3B Ignition Module (No Heatsink)
Ignition Coil & Module
54
Principal of operation: Inductive discharge
Construction: Resin-shrouded H.T. coil. Electronic power module.
Aluminium alloy mounting chassis, also acting as a heat sink/dissipator and electrical
shield.
Electrical connections: Standard automotive electrical connectors:
7-pin minitimer, male spade and H.T.

WCM016 Coil & Module Assembly AEI 600A
Ignition Coil
55
Principle of operation: Inductive discharge.
Construction: Resin shrouded HT coil steel mounting bracket.
Electrical connections: Standard automotive electrical connectors: male spade and HT.
Electrical characteristics: Primary coil resistance 0.35 Ohm.

WIC003 Ignition Coil BAE 209
Ignition Coils
56
High tension connection.
Adaptors are availble for the high tension
connector
(Part Number 9990256600, Pack of 6).
Type: Double ended coil.

Principal of operation: Inductive discharge.
Construction: Resin shrouded HT coil with steel banded core.
Electrical connections: 3 pin minitimer (EK).
Pin1 - Coil positive.
Pin 2 - Common with pin 1.
Pin 3 - Coil negative.
2 pin Packard connector (AK) (9990152500).
Two HT pillars (Standard post AK, VW post EK).
Electrical characteristics: Primary coil resistance 0.55 Ohms.

WIC031 Double Ended Ignition Coil (Std HT Post, Packard Connector) BAE 800AK
WIC130 Double Ended Ignition Coil (VW HT Post, Minitimer Connector) BAE 800EK
4 Cylinder Static Ignition Coils
57
Adaptors are availble for the high tension
connector
GENERAL SPECIFICATION (Part Number 9990256600, Pack of 6).
WIC062

Construction: Resin shrouded HT coil.
Electrical connections: Standard 4-way minitimer connector.
Pin 1 - Coil negative plugs 1 & 4.
Pin 3 - Coil positive.
Pin 4 - Common.

WIC133

Electrical connections: Ford 3 pin connector.
Pin 1 - Coil negative, plugs 1 & 4.
Pin 3 - Coil negative, plugs 2 & 3.

WIC062 Static Ignition Coil - General 4 Cylinder (4 Pin Connector) BAE 04
WIC133 Static Ignition Coil - Ford Zetec 4 Cylinder (3 Pin Connector) N/A
4 Cylinder Static Ignition Coil
58
Adaptors are available for the high

tension connector (Part Number
9990256600, Pack of 6).
WIC134

Electrical connections: Standard 3 way minitimer connector.
Pin 1 - Coil negative plugs 1&4.
Pin 3 - Coil Negative plugs 2&3.
Four HT pillars.
WIC062 Coil Bracket
Material: 3mm mild steel, laser cut.

Finish: Zinc & yellow passivated.
Fixings: Four threaded inserts.
Four M5 x 50mm cap head bolts.

WIC134 Static Ignition Coil - General 4 Cylinder Bosch
9990295800 WIC062 Coil Bracket N/A
Plug Top Coils
59
6070703800
WIC131

Electrical connections: Standard 3-way minitimer connector.
Pin 1 - 12 volt Power.
Pin 2 - Ground.
Pin 3 - Coil Signal.
WIC041
Principle of operation: Inductive discharge

WIC131 Plug Top Coil BAE 700 AK
WIC041 Plug Top Coil BMW
60
Ballast Resistor
Electrical resistance: 1 Ohm at 20˚ Celcius.

Electrical connections: Solder tag.

9990195600 Ballast Resistor 1.0 Ohm
6 Cylinder Static Ignition Coil
61
Adaptors are available for

the high tension connector
(Part Number 9990256600,
Pack of 6).

Electrical connections: Standard 4 way minitimer.
Connections: Pin 1 - Coil negative plugs 2 & 5.
Six HT pillars.

WIC135 Static Ignition Coil - 6 Cylinder Bosch
Spark Plug Leads
62
Webcon stock a wide range of our own manufactured, high quality plug leads equivalent to O.E.
Specification, with purpose made outer jackets for maximum oil, water and temperature resistance.
If we do not stock a specific lead set Webcon can custom build a set of leads to your requirements.
We also stock a wide range of other spark plugs & leads, coils, distributor caps, rotor arms, points
and condensers for standard vehicle applications, please phone for details of availability and price.
Part Number Ignition Type Application

AIL294 WIC062 Normally Aspirated Cosworth
AIL188 WIC016 Ford 1.6 CVH
AIL170 WIC016 Ford Zetec 1.6 16v, 1.8 16v & 2.0 16v
AIL232 WIC062 Ford Pinto 1.6/2.0 & Ford X-Flow 8v Static
AIL174 WIC016 Ford X-Flow Static 1.3, 1.6 & 1.7
AIL076 Distributor Peugeot/Citroën 1.9 8v
AIL214 Static Peugeot/Citroën 1.6 8v & 1.9 8v
AIL053 WIC062 Peugeot/Citroën XU9 1.6 8v & 1.9 8v
WIL013 Distributor Renault 19 1.8 16v
AIL095 Distributor Rover A-Series
AIL251 WIC062 Rover A-Series
TBA WIC062 Longitudinally Mounted A-Series
AIL064 WIL134 & Distributor Vauxhall/Opel XE 2.0 16v
AIL195 WIC062 Vauxhall/Opel Ecotec 2.0 16v
AIL085 WIC062 & Distributor VW 1.8 8v & 16v
63
Temperature Semsors
Type Length X Type Length Y
(mm) (mm)
WTS05 27 ATS04 27
WTS09 18 ATS07 17
WTS Type
Sensor type: NTC-type thermistor.

Construction: Threaded brass body.
Electrical connection: Standard 2-pin Minitimer connector.
Tightening torque: <25Nm.
Thread Size: M12 x 1.5.
ATS Type
Sensor type: NTC-type thermistor.

Construction: Threaded brass body with a slotted plastic frame.
Thread Size: M14 x 1.5.

WAS009 Air Temperature Sensor ATS04
WTS186 Coolant Temperature Sensor WTS05
WTS185 Coolant Temperature Sensor WTS09
64
Standard Coolant Temperature Sensors
Length
Type (mm) Colour
WTS155 28 Black
WTS104 28 Blue
Part number: WTS104/155

Sensor type: Thermistor.
Tightening torque: <25Nm
Thread Size: M12x1.5
Length
Type (mm) Colour
WTS133 22 Black
Part number: WTS133.

Sensor type: Thermistor.
Thread Size: 1/8 x 27 NPTF tapered thread.

WTS104 Coolant Temperature Sensor - Vauxhall Type
WTS155 Coolant Temperature Sensor - Vauxhall Type
WTS133 Coolant Temperature Sensor - Ford Zetec
65
Air Temperature Sensors
Connection Housing
Sensor Kit Contents
ATS05 Air temp sensor: NTC-type thermistor.

Construction: Plastic moulded body, flange mounting for two Ø3mm or 1/8”.
Electrical connection: 2-pin Packard connector.
Connector: Plastic moulding with rubber seal connector housing.
Pins: 2 x Female crimp-type contacts.
Connector Kit Contents
• One connector and two female pins as described above.

9990152700 Air Temperature Sensor Kit ATS05
9990224500 ATS05 Connector Kit N/A
66
Air Pressure Sensors
Pressure Sensor Type: Ratiometric absolute pressure sensor.

Construction: Hard wearing plastic body.
Mechanical operation: Ceramic diaphragm coupled to an electrical strain gauge.
Electrical connection: Standard 3-pin minitimer connector.
Pin Out
Pin 1 Signal
Pin 2 Ground
Pin 3 5V Ref.
Part Number Type Pressure Range (Bar)

WMS013 APS02/03 0-2
WMS014 APS05/01 0-3
67
Air Pressure Sensors
Pressure Sensor Type: Ratiometric absolute pressure sensor.

Construction: Hard wearing black plastic body.
Mechanical operation: Ceramic diaphragm coupled to an electrical strain gauge.
Electrical connection: Standard 3-pin minitimer connector.
Pin Out
Pin 1 Signal
Pin 2 Ground
Pin 3 5V Ref.
Part Number Product Description Type Pressure Range

(Bar)
WMS019 Pressure Sensor PRT03/04 0-1
68
Speed Sensors
Type 1
Type 2
Speed Sensors: SEN 8*. Variable reluctance, electromagnetic sensor (open magnetic flux type) driven
by toothed (phonic) wheels SEN8D3 is a shielded version of the SEN8D with a 3 pin
minitimer connector.
Bracket: Suitable for mounting SEN 8 type speed sensors. 2.5mm mild steel plate finished Zinc
and yellow passivate.
Product L M
Part Number Description (mm) (mm) Type
WSS075 (Magnetti Marelli - Type 1) 460 20.7 SEN8D
WSS076 (Magnetti Marelli - Type 2) 460 20.7 SEN8K
WSS077 (Magnetti Marelli - Type 1) 460 20.7 SEN8D3
WSS001 (Type 1) 460 30 SEN8E
WSS002 (Type 2) 565 30 SEN8LA
WSS003 (Type 2) 465 13.5 SEN8M
WSS004 (Type 1) 1160 20.7 SEN8V
WSS005 (Type 1) 460 20.7 SEN8L
WSS022 (Type 1) 460 20.7 SEN8D3
WSS030 (Type 2) 450 30 SEN8I3
WSS032 (Type 2) 750 30 SEN8X
WSS026 VW Golf 2.0 8v & 16v - 1992 on N/A 30.5 N/A
WSS006 Rover K Series 1.4 16v 260 31 N/A
WSS051 Vauxhall/Opel XE 2.0 16v 995 24.5 N/A
WSS074 Ford Zetec 1.6 16v & 2.0 16v N/A 37 N/A
WSS078 Ford CFi Crank Sensor 35 40 N/A
WPU088 Camshaft Phase Sensor
(For Distributor Fitment) N/A N/A N/A
9990154600 Bracket N/A N/A N/A
69
Crankshaft RPM Trigger Discs
9990119200 9990139500
9990144300 9990141400
9990151200 9990154800
9990163800 9990164300
Material: 4mm thick HR15 mild steel (BS1449:1) Zinc plated and yellow passivated.

9990119200 Trigger Disc 4 Cylinder General In-line
9990139500 Trigger Disc 4 Cylinder Mercedes 190E In-line
9990141400 Trigger Disc 8 Cylinder Range Rover V8
9990144300 Trigger Disc 6 Cylinder BMW In-line 6
9990151200 Trigger Disc 4 Cylinder BDR In-line
9990154800 Trigger Disc 8 Cylinder Rover V8
9990163800 Trigger Disc 4 Cylinder A-Series In-line
9990164300 Trigger Disc 6 Cylinder Porsche Flat 6
70
36-1 Crankshaft RPM Trigger Discs
Single Hole Mounting
Triple Hole Mounting
Peugeot 205 / Multi Slot

Mounting
Crankshaft trigger discs with 36 - 1 teeth (Ford EECIV) for fitment to engines without an original
equipment RPM trigger.
Material: 4mm thick HR15 mild steel (BS1449:1)

Zinc plated and yellow passivated.

9990240400 Trigger Disc 36-1 Teeth Single Hole Mounting
9990289900 Trigger Disc 36-1 Teeth Triple Hole Mounting
9990291600 Trigger Disc 36-1 Teeth Multi-slot Mounting
71
Specific Trigger Disc Kits
Ford Pinto Ford X-Flow
1.6 & 2.0 1.3, 1.6, 1.7 8v
Ford CVH
1.3, 1.6 & 1.8
Peugeot/Citroën
1.6 & 1.9 8v
Each kit is supplied with the following:

• A speed sensor and mounting bracket.
• 36-1 trigger disc and a mounting boss.
All that is required is a hole to be drilled in the standard pulley wheel for accurate trigger disc
location (except Peugeot/Citroën).
Specific trigger disc kits can be developed upon request.

9990291500 Ford Pinto Trigger Disc Kit
9990291400 Ford X-Flow Trigger Disc Kit
9990295600 Ford CVH Trigger Disc Kit
9990295700 Peugeot/Citroën 1.6 & 1.9 Trigger Disc Kit
Contact
Alpha Group Rover A-Series Trigger Disc Kit
72
Cold Start Air Valve
Air valve and die cast housing assembly.
Part Number 3717000102
Control: Electrically operated air valve.

Valve construction: Fully sealed unit.
Electrical: Standard 2-pin minitimer connection.
Housing: Die-cast aluminium alloy.

WID028 Idle Air Valve 01/10 Standard Flow
WID029 Idle Air Valve 04/00 High Flow
3717000102 Assembly VAE 06/01 & Die Cast Housing
4156505000 Replacement ‘O’ Ring 24mm O/D
4156505100 Replacement ‘O’ Ring 30mm O/D
N.B. VAE 01/10 and VAE 06/01 have the same operational characteristics.

9990139600 Hose (Used For Idle Air Valve Circuit) I/D 16
9990043400 Herbie ‘J’ Clip 21 - 24
9990110700 90˚ Shaped Hose I/D 16
N.B. Hose (Part Number 9990139600) is available in lengths as required.
Cold Start Air Valve Mounting Kit
73
• Black plastic air valve housing with parallel unions.

• Complete with black finished mounting bracket and fittings.

9990167100 Air Valve Mounting Kit (Plastic)
Cold Start Air Manifolds
74
Material: Cast aluminium alloy.

Finish: Hard wearing black crinkle coating.
Installation: For use with twin throttle body assemblies to provide passage for extra air to the engine side of the
throttle plates during the cold start phase.
Installation Examples:
• For 4 cylinder application - 2 x 9990135500 required.
• For 6 cylinder application - 2 x 9990133500 + 1 x 9990146400 required.

9990135500 Cold Start Air Manifold (One End Closed)
9990146400 Cold Start Air Manifold (Straight Through)
75
Lambda Sensor & Boss
Part Number: Part Number:
9990200700 9990200800
Heated exhaust gas Zirconia oxygen sensor
Operating point: AFR = 14.6:1, sensor output 450mV.

Maximum fuel lead content: 0.003g/l (unleaded fuel only).
Heater: 14 Volt - 1 Amp.
Exhaust gas temp. range: 200 - 850˚ Centigrade.
(Required for representative output).
Electrical connection: Sealed three wire type.
Tightening torque: 41Nm ±4Nm.
Thread: M18 x 1.5

WLS331 Lambda Sensor (OE fitment)
ALS331 Lambda Sensor (Alpha Wiring Harnesses)
9990200700 Lambda Sensor Mounting Boss
9990200800 Lambda Sensor Mounting Boss Blanking Plug
Alpha Publicity Material
76
Part Number Product Description Dimns (mm)
9990249700 Medium Alpha ‘Cut Out’ Decal 230 x 40
9990249600 Medium Alpha Sticker 195 x 45
9990250300 Medium Alpha ‘Cut Out’ Decal (White) 231 x 38
9990255000 Small Alpha ‘Cut Out’ Decal 130 x 20
9990255100 Large Alpha ‘Cut Out’ Decal 608 x 100
9990261600 Medium Alpha ‘Cut Out’ Decal (White Reflective) 230 x 40
9990276700 Alpha Windscreen Banner 1500 x 200
Alpha Plus & Plus 2 Calibration Equipment
77
The calibration console is compatible for use with the Alpha Plus and Plus 2 engine management
systems and calibration development software.
The console makes ‘real time’ adjustments to the calibration values of the Alpha Plus & Plus 2
E.M.S. The AMC comes complete with a communications interface which enables
communications between the Alpha Plus ECU and the PC for real time active engine data display.
The interface is connected to the PC parallel port and the Alpha Plus wiring harness. Nominal
current draw - 250mA.
Dimensions: 190mm x 138mm x 65mm

T100 Calibration Console
Alpha Plus Calibration Equipment
78
Communications Interface Cable T020

• Connects the communications interface to the Alpha Plus wiring harness.
Communications Interface Cable T024

• Connects the communications interface to the PC parallel port.
Ram Board TO22

• Used to upgraded any Alpha Plus ECU to the development ECU specification level. This device
contains 8K of temporary memory space and when fitted is sufficient to store a calibration for
“real time” active mapping.

T020 Communications Interface Cable - 9-Way (4.5m)
T022 RAM Board
T024 Communications Interface Cable - 25-Way
9990220600 Communications Interface Cable - 9-Way (2.5m)
9990205600 Development ECU EPROM 27256
9990202800 Production ECU EPROM 27128
79
Dealer Equipment
Synchrometer
The synchrometer is used to balance the air flow

through the throttles of a multi-throttle inlet system.The
scale reads from 1 to 30 or 2 to 50 kg/hour and permits
a very high airflow without affecting the mixture
strength.
The conical rubber end suits circular intakes from 30 to
50mm.
Flow Range
Part Number Product Description (Kg/Hour)
9800099900 Synchrometer 2 - 50
9800100000 Synchrometer 1 - 30
9800100600 90˚ Adaptor N/A
Spark Tester
The spark tester provides safe spark testing

enclosed within a sealed clear plastic tube.
Hight tension connection is by means of a
standard coil type connector and a crocodile
clip for grounding the other terminal.

9802215000 Spark Tester
Lambda Sensor Socket
The useful tool allows easy removal of Lambda

sensors. A cut out down one side of the socket allows
the lead to be moved out of the way. A must for any tool
kit.

TE13710 Lambda Sensor Socket
80
Dealer Equipment
Potentiometer Setting Tool
The potentiometer setting tool is used for setting the position of PF3B and PF4B potentiometers
to ALPHA throttle bodies, without the need for wiring the system up to a computer and calibration
equipment. This is very useful for on the spot checks and regular services of the system.

9990140400 Potentiometer Setting Tool
Fuel Injection Test Kit
Packaged in a sturdy plastic case, this kit includes a selection of “Noid-Lites”, the quickest and
easiest way tp check electronic fuel injection signals. Also supplied are the latest, Quick-
Disconnect tools for fuel injection lines.

TE13716 Fuel Injection Test Kit
81
Lambda Display Systems
Compact and lightweight Lambda display systems finished in an attractive black textured plastic
casing. The AF-1 display features 14 LED’s, and the AFS-2 display features 20 LED’s which are
colour coded to assist quick and accurate fuel calibration.
The Lambda display units are supplied as part of a complete system which includes the following
parts:
• 1 x AFS-1/AFS-2 Lambda display unit (requires +12 Volt supply).
• 1 x Oxygen sensor.
• 1 x Wiring harness with spade type fuse.
• 1 x Weldable sensor boss with plug and gasket.
• 4 x Velcro mounting strips.
• 3 x Crimp connectors.
• 1 x Instructions and wiring diagram leaflet.
Sizes: AFS-1 70mm x 40mm x 15mm.

AFS-2 130mm x 65mm x 25mm.
The Lambda sensor measures the free oxygen in the exhaust gas and ranges between 12:1 rich
and 15.5:1 lean A.F.R. The operating temperature of the sensor is between 500˚ to 900˚ Celsius.

AFS-1 Lambda Display System
AFS-2 Lambda Display System
WLS330 Lambda Sensor For Lambda Display System
9990200700 Lambda Sensor Mounting Boss
9990200800 Lambda Sensor Mounting Boss Blanking Plug
82
RPM Limiter
A high performance RPM limiter designed for use with contact breaker or electronic ignition
systems (excluding multiple firing and capacitive ignition systems). Easily adjustable by the user
for ultimate engine protection.
The unit operates by counting the ignition sparking frequency which then determines the engine
RPM, then a soft cut pre-determined ignition limit is enforced.
Features:
• Range 5,200-10,000RPM.
• Soft cut.
• Size 71mm x 49mm x 25mm.
• Basic wiring loom.

ARL1 Alpha RPM Limiter
Sequential Gear Shift Display
83
A gear shift indicator incorporating six LED’s that illuminate in sequence as you approach the
optimumgear shift engine speed. The design features include the increasing size and brightness
of the LED’s and the final ultra-bright red LED that illuminates at the pre-set engine speed. The
purpose of the sequential operation is to inform the driver of the approaching gear change point
and takes into account the rate of engine acceleration in different gears. This method has been
used to great effect in Formula 1, Super Touring, World Rally Championship and other top
motorsport formulae.
Features:
• 6 Ultra-bright water clear light emitting diodes: 3 x 5mm green, 2 x 8mm green,1 x 10mm red.
• All LEDs are clearly visible in bright sunlight.
• Display range 90-100% of set maximum engine speed, e.g. 5400-6000rpm.
• Simple 3 wire connection - 12V power supply, ground and ignition coil negative.
• Fully user programmable with half engine speed switch for easy setting.
• Instantaneous response.
• Suitable for 4, 6, 8 and 12 cylinder engines
• Suitable for distributor or distributorless ignition systems.
• Supplied with universal harness.
• Reverse polarity protected.
• Dimensions : H=25mm, W=73mm, D=51mm

T050 Sequential Gear Shift Display Unit
Gear Shift Light Kits
84
A gear change kit that incorporates everything to connect to the ALPHA systems shift lamp output.
A mounting bracket is also supplied as well as comprehensive fitting instructions.
Features:
• 1 x 8mm Ultra-bright water clear light emitting diode available in red or green.
• Ultra-bright LEDs are clearly visible in bright sunlight.
• Suitable for use with the output from an ALPHA or ALPHA PLUS ECU.
• Simple 2 wire connection - 12V power supply and output from ECU.
• Complete with comprehensive fitting instructions.

9990241500 Gear Shift Lamp Kit (Red)
9990274500 Gear Shift Lamp Kit (Green)
85
Catalogues/Brochures
Standard Motor Products Europe Limited distribute a wide range of fuel system products including
WEBER performance carburettor kits, SOLEX carburettors, fuel pumps & filters, carburettor
service kits, manifolds & linkage systems.
We also stock an extensive range of original equipement and aftermarket service parts including
a complete range of ignition components, distributor pickups and caps, crank sensors, rotor arms,
lead sets, temperature sensors, brake light switches and much much more.
To compliment the product portfolio a comprehensive range of remanufactured ECU’s, airflow

meters and turbochargers are carried.

9500005400 Carburettor Tuning Manual
9555001900 A Simple Carburettor Tuning Instrument - Synchronometer Catalogue
9555500100 No.1 Direct Replacement Carburettor Catalogue
9555500200 Installation Components & Accessories Catalogue
9555519600 Carburettor Service Kit Catalogue
9555520900 No.2 Solex Carburettor Catalogue
9555523800 Weber Carburettors For Citroën & Peugeot Cars Catalogue
9555523900 Weber Carburettors For Fiat Cars Catalogue
9555524000 Weber Carburettors For Ford Cars Catalogue
9555524200 Weber Carburettors For Renault Cars Catalogue
9555524300 Weber Carburettors For Vauxhall/Opel Cars Catalogue
9555552200 Air Horns Catalogue
9990277700 Webcon Engine Management Components Catalogue on CD-ROM
9555530100 Engine Management Components Catalogue
9555540200 Engine Ignition Components Catalogue
Accessories
SEQUENTIAL GEAR CHANGE DISPLAY (T050)
A gear change indicator incorporating 6 lamps that illuminate in sequence as you approach
the optimum gear change engine speed.
The design features include:
- Increasing size and brightness of the LED’s.
- A final ultrabright red LED that illuminates at the preset engine speed.
- Simple 3 wire connection.
- Fully user programmable with half engine speed switch for easy setting.
LAMBDA DISPLAY SYSTEM

High performance engine tuning using ‘Engine Management’ technology at DIY prices.
Both the AFS-1 and AFS-2 offer a cost effective option to Dyno/Rolling road tuning.
Accurately monitor the fuelling characteristics of your engine while driving on the road, off-
road or on the track, in order to assess the calibration of your fuel system, whether it be
fuel injection or carburation.
Both kits include:

- Heated Lambda (oxygen) sensor and weldable sensor boss, gasket and
sealing plug.
- Wiring loom, fuse, crimp connectors and velcro mounting strips.
- Comprehensive instructions.
Part No. AFS-1 AFS-2

LxHxD 70mm x 40mm x 15mm 130mm x 65mm x 25mm
LINKAGE KITS
There are four different versions of linkage kit suitable for DCOE carburettors, for either top
or bottom mounting, for single or twin cable operation. All can be used on single or twin
carburettor installations and all can be fitted with the cable routed from either side.
Performance Kits Performance Kits
There are three versions of linkage kit suitable for fitment to Alpha throttle bodies. Two ALPHA PLUS FULL ENGINE MANAGEMENT PERFORMANCE KITS
utilise the existing DCOE throttle linkage kits LP1000 and LP2000 with the addition of the These hi-tech multi-throttle engine management systems release the performance potential
of a wide variety of production engines. Developed from knowledge gained developing (D) = Distributor GOLD SILVER BRONZE
top mounting bracket 9990172100.
SuperTouring race engines. All kits cover both fuel injection and ignition requirements in a fully (S) = Static/Wasted Spark KIT KIT KIT
Suitable for 38, 40, 45, 48 and 50mm venturis sizes.
Order No. Description intergrated package. Supplied as total bolt-on packages, all kits feature closed loop Lambda
PRODUCT
LP1000 Top mounting for single cable operation incorporates a clamp-on ferrule control and are supplied with a Lambda sensor for use with exhaust catalytic converters. The K97013 (D)
kits are supplied ready calibrated for standard specification engines. For other states of tune General 3 K9800
for use with the existing throttle cable. (DCOE). K97014 (S)
please contact us.
LP2000 Top mounting for twin cable operation. Kit includes twin cables.
All Kits Contain: K99001
(DCOE). 45mm DCOE
2 x ALPHA throttle bodies, JR air filters, wiring harness, throttle linkage system, fuel injectors,
LP3000 Bottom mounting for single cable operation incorporates a clamp-on ALPHA engine management system, fitting instructions and setting procedure. Ford Zetec K99006
K99010 K97017
RANGE
ferrule for use with the existing throttle cable. (DCOE). 1.8 16V 40mm DCOE + small air filters
LP4000 Bottom mounting for twin cable operation. Kit includes twin cables. Typical Power Figures Standard Alpha Plus K99007
40mm DCOE
(DCOE). Ford Zetec 2.0 litre 130 bhp 165 bhp
LP7000 Bottom mounting for twin cable operation. Kit includes twin cables. Vauxhall/Opel XE 2.0 litre 150 bhp 180 bhp Ford Zetec K99002
Vauxhall/Opel Ecotec 2.0 litre (Fast Road Cams) 132 bhp 170 bhp K99011 K97017
(Throttle Bodies). GOLD 2.0 16V 45mm DCOE
9990172100 Top mounting bracket.
2001
Ford Kent K97015 (D)
WEBER ALPHA CARBURETTOR PERFORMANCE KITS K99019
1.7 8V K97016 (S)
These kits combine the legendary WEBER DCOE carburettor and the hi-tec ALPHA 3D
mapped ignition system. This proven combination releases the performance potential of a K99020 (D)
wide variety of production engines, and covers both fuelling and ignition requirements in a Ford Pinto 45mm DCOE K97027 (D)
fully integrated package. Supplied as complete, bolt-on packages, the kits are calibrated and 2.0 8V K99021 (S) K97028 (S)
45mm DCOE
mapped for standard production engines. For other states of tune please contact us.
Each kit includes: K99008 (D)
2 x WEBER DCOE carburettors, ALPHA 3D ignition system, throttle linkage, JR air filters, Peugeot/CitroÎ n XU9 40mm DCOE K97025 (D)
For further information, please contact: K99018
wiring harness, inlet manifold, throttle position sensor and fitting instructions. 1.9 8V K99009 (S) K97026 (S)
Standard Motor Products Europe Limited 40mm DCOE
Dolphin Road, Sunbury, Middlesex, TW16 7HE, ENGLAND
Typical Power Figures Standard Alpha
Tel: +44 (0) 1932 787100 Fax: +44 (0) 1932 782725 Renault Clio/19
Internet: www.smpeurope.co.uk E-mail: sales@webcon.co.uk Ford Zetec 1.8 litre 115 bhp 155 bhp K20003
1.8 16V
Ford Zetec 2.0 litre 130 bhp 165 bhp
A member of the Standard Motor Products Group Vauxhall/Opel XE 2.0 litre 150 bhp 180 bhp Renault Clio 172
K20013
2.0 16V
SILVER
K99004 (D)
Vauxhall XE K99012 (D) 45mm DCOE K97018 (D)
ALPHA IGNITION ONLY MANAGEMENT KITS 2.0 16V K99013 (S) K99005 (S) K97019 (S)
A state of the art 2-Dimensional electronic ignition system featuring an ignition map of 16 RPM 45mm DCOE
sites that can be upgraded to full 3-Dimensional ignition management by the addition of a
Vauxhall/Opel Ecotec
throttle position sensor (16 RPM x 16 engine load sites). The system is suitable for static (4 K99016
2.0 16V
cylinder) or distributor ignition systems. The system features an engine speed limiter, and
there is also a tachometer output drive and a gearshift indicator lamp drive. Volkswagen
All kits contain: K20002
1.8 16V
Electronic Control Unit (PI150), wiring harness, inlet air temperature sensor and cable ties.
(For certain engines, e.g. Ford Pinto, that are not factory fitted with an RPM sensor, also
include a crank sensor and trigger disc kit).
RPM Limiter Data Acquisition
Both of the above kits (static/distributor) can be upgraded to full 3D ignition timing by
the addition of a throttle position sensor (see below). All general Alpha Ignition
Management systems are supplied with a safe base ignition map, ideal for checking
correct installation. Engine specific systems are supplied with a calibration for a
standard specification engine. General systems must be calibrated by
an Alpha systems dealer to obtain the maximum benefit. BRONZE ARL1 is designed for use A data acquisition system
with contact breaker and is now a fundamental
THROTTLE POSITION KITS FOR SIDEDRAUGHT CARBURETTORS electronic ignition development tool for any
These kits include the throttle position sensor and all brackets and screws needed to mount to WEBER systems (but not multiple successful engine tuner or
sidedraught DCO carburettors and Dellorto DHLA carburettors. Quick and easy to fit, there is no machining firing or capacitive motorsport team. The
required and comprehensive fitting instructions are included. ignition systems) to A L P H A Data Acquisition
For use with all ‘ALPHA Ignition Only Management Kits’. Connects straight into the wiring harness to avoid engine damage System will provide
instantly convert the ignition system from 2-Dimensional to 3-Dimensional. due to over revving. comprehensive and
9990266000 TPS Kit (40/45 DCOE) The operating range is detailed analysis of the
9990266800 TPS Kit (48 DCO SP) 5,200 - 10,000 RPM and performance of engine, vehicle and driver.
9990290200 TPS Kit (40/45 DHLA) features a soft cut limiter. If you know what went wrong, you can correct it.
If you know what went right, you can repeat it.
86
Customers’ Cars
Ford Ka
2.0 16v Zetec
July 2000
Vauxhall Nova
2.0 16v XE
July 2000
Tiger 6
2.0 16v Zetec
March 2001
VW Golf 1.8 16v

167 bhp (124kW) @ Flywheel
As featured in “Performance VW”
August 2000
87
Index
A DCOE/Distributor): 10
Vauxhall/Opel XE 2.0 16v (45
Air Horn DCOE/Static): 10
40 DCOE
Length 16: 24 C
Length 26: 24 Calibration Equipment
Length 39: 24 Alpha Plus
40mm & 45mm T/Bodies Communications Interface Cable - 25-
Length 40: 24 Way: 78
Length 52: 24 Communications Interface Cable - 9-Way
45 DCOE (2.5m): 78
Length 16: 24 Communications Interface Cable - 9-Way
Length 26: 24 (4.5m): 78
Length 39: 24 Development ECU EPROM 27256: 78
Length 62: 24 Production ECU EPROM 27128: 78
48 DCO/SP RAM Board: 78
Length 95: 24 Alpha Plus and Plus 2
48 DCOE & T/Bodies Calibration Console: 77
Length 56.5: 24 Catalogues/Brochures
Alpha Kits A Simple Carburettor Tuning Instrument -
Bronze Synchronometer Catalogue: 85
Ford Kent 1.7 8v (Distributor): 11 Air Horns Catalogue: 85
Ford Kent 1.7 8v (Static): 11 Carburettor Service Kit Catalogue: 85
Ford Pinto 2.0 8v (Distributor): 11 Carburettor Tuning Manual: 85
Ford Pinto 2.0 8v (Static): 11 Engine Ignition Components Catalogue:
Ford Zetec 1.8 16v & 2.0 16v: 11 85
General (Distributor): 11 Engine Management Components
General (Static): 11 Catalogue: 85
Peugeot/Citroën XU9 1.9 8v (Distributor): Installation Components & Accessories
11 Catalogue: 85
Peugeot/Citroën XU9 1.9 8v (Static): 11 No.1 Direct Replacement Carburettor
Vauxhall/Opel XE 2.0 16v (Distributor): 11
Catalogue: 85
Vauxhall/Opel XE 2.0 16v (Static): 11
No.2 Solex Carburettor Catalogue: 85
Gold
Webcon Engine Management
Ford Kent 1.7 8v (Static): 9
Components Catalogue on CD-ROM: 85
Ford Zetec 1.8 16v: 9
Ford Zetec 2.0 16v: 9 Weber Carburettors For Citroën & Peugeot
General: 9 Cars Catalogue: 85
Peugeot/Citroën (XU9) 1.9 8v (Static): 9 Weber Carburettors For Fiat Cars
Renault Clio Sport 172 2.0 16v (Static): 9 Catalogue: 85
Renault Clio/19 1.8 16v (Distributor): 9 Weber Carburettors For Ford Cars
Vauxhall Ecotec 2.0 16v: 9 Catalogue: 85
Vauxhall/Opel XE 2.0 16v (Distributor): 9 Weber Carburettors For Renault Cars
Vauxhall/Opel XE 2.0 16v (Static): 9 Catalogue: 85
VW 1.8 16v (Static): 9 Weber Carburettors For Vauxhall/Opel
Silver Cars Catalogue: 85
Ford Pinto 2.0 8v (45 DCOE/Distributor): Cold Start
10 Accessories
Ford Pinto 2.0 8v (45 DCOE/Static): 10 90˚ Shaped Hose: 72
Ford Zetec 1.8 16v (40 DCOE & Small Herbie ‘J’ Clip: 72
Air Filters): 10 Hose (Used For Idle Air Valve Circuit): 72
Ford Zetec 1.8 16v (40 DCOE): 10 Air Manifold
Ford Zetec 1.8 16v (45 DCOE): 10 One End Closed: 74
Ford Zetec 2.0 16v (45 DCOE): 10 Straight Through: 74
Peugeot/Citroën XU9 1.9 8v (40 Air Valve Mounting Kit (Plastic): 73
DCOE/Distributor): 10 Idle Air Valve
Peugeot/Citroën XU9 1.9 8v (40
01/10 Standard Flow: 72
DCOE/Static): 10
04/00 High Flow: 72
Vauxhall/Opel XE 2.0 16v (45
88
Index
Spares Terminal - Early ‘Pop Up’ Button Type:
Assembly VAE 06/01 & Die Cast 14
Housing: 72 Packard
Replacement ‘O’ Ring 24mm O/D: 72 2-Way (BAE800AK Coil & ATS05): 14
Replacement ‘O’ Ring 30mm O/D: 72 Terminal Pin: 14
Relay: 14
D Relay Holder: 14
Dealer Equipment Ford 3-Pin Static Ignition Coil
Fuel Injection Test Kit: 80 Seal: 14
Lambda Sensor Socket: 79 Terminal Pin 2: 14
Potentiometer Setting Tool: 80 Terminal Pins 1 & 3: 14
Spark Tester: 79 Male Minitimer
Synchrometer 1-30 Kg/Hr: 79 2-Pin Black: 14
Synchrometer 2-50 Kg/Hr: 79 3-Pin Black: 13
Synchrometer 90˚ Adaptor: 79 Terminal Pin: 14
Mountable Cable Tie: 14
E Sureseal
ECU's Female Pin: 14
Alpha Ignition Only: 8 Male Pin: 14
Retaining Bracket: 8 Recepticle Housing: 14
For Alpha Type Signal Frame: 7 Wiring Harness Grommet 45mm To 50mm
For Original Equipment Signal Frame Hole: 14
Interface: 7
Micro Controller: 7
F
Electrical Fittings Fuel
Connector Filter
Fittings
CD Pack
Union Ø 8 x 12mm - Plated Mild Steel -
Connector 6-Pin White: 14
43mm Long: 43
Terminal Pin: 14
Union Ø 8 x 12mm - Plated Mild Steel -
Female Lambda Sensor
28mm Long: 43
Connector (9990205300 Harness): 14
In-Tank
Spacer: 14
40 Micron In-tank Fuel Filter: 43
Female Minitimer
Union & In-tank Filter Assembly: 43
2-Pin Black: 13
Metal
2-Pin Blue: 13
12mm Dowty Washer: 40
2-Pin Brown: 13
14mm Dowty Washer: 40
2-Pin Green: 13
Fuel Filter (55mm O/D): 40
2-Pin Grey: 13
Fuel Filter (58mm O/D): 40
2-Pin White: 13
M12 x 1.5 Banjo Bolt: 40
3-Pin Black: 13
Ø8 Push-On Hose Connector (M14 x
35-Pin Black: 13
1.5): 40
4-Pin Black: 13
Ø8 Push-On Hose Connector Banjo
7-Pin Black: 13
(12mm): 40
Pin (High Spec.) 0.5-1.0mm Wire: 13
Ø8 Push-on Hose Connector Banjo
Pin (High Spec.) 1.0-2.5mm Wire: 13
(14mm): 40
Pin 0.5-1.5mm Wire: 13
Rubber Boot 2-Pin: 13 Plastic
Rubber Boot 2-Pin - 90˚: 13 Filter: 41
Rubber Boot 3-Pin: 13 Filter/Pump Mounting Kit: 42
Rubber Boot 4-Pin: 13 Hoses & Fittings
Rubber Boot 7-Pin: 13 10 I/D 180˚ Shaped Hose: 49
Fuse 14mm Hose Clip: 49
10 Amp Blade Fuse: 14 18mm Herbie Clip: 49
15 Amp Blade Fuse: 14 5.8 I/D 12.0 O/D: 49
Holder (Supplied With Terminals): 14 7.4 I/D 13.5 O/D: 49
Inertia Switch 9.5 I/D 15.5 O/D: 49
3-Pin Female Inertia Switch Connector Cobra Clip: 49
Kit: 14 Cobra Clip Pliers: 49
Connector - Early ‘Pop Up’ Button Type: Injector
14 L/H Elbow With Injector Port: 16
89
Index
Pico RPM58: 46
IWP001: 33 4.5 Bar
IWP023: 33 RPM73: 46
IWP042: 33 6.0 Bar
IWP043: 33 RPF22/01: 47
IWP069: 33 Pump
Weber High Pressure
IW031 (Green): 32 100Li/Hr @ 3 Bar: 37
IW042 (Red): 32 100Li/Hr @ 5 Bar: 38
IW052 (Brown): 32 170Li/Hr @ 3 Bar: 39
IW058U (Biege): 32 Low Pressure
Injector Mounting Kits 90-130Li/Hr 0.17-0.31 Bar: 36
Pico 90-130Li/Hr 0.34-0.62 Bar: 36
Injector Clearance Kit: 35 G
Injector Mounting Kit (Double Fuel
Union): 35 Gaskets
Injector Mounting Kit (Single Fuel 40mm Flange Gasket: 29
Union): 35 45mm Flange Gasket: 29
Weber 48mm Flange Gasket: 29
13mm Fuel Hose Clip: 34 50mm Flange Gasket: 29
Injector Fuel Union Kit (Double): 34 Gear Shift
Injector Fuel Union Kit (Single): 34
Lamp Kit (Green): 84
Injector Mounting Cup: 34
Injector Mounting Kit (Double): 34 Lamp Kit (Red): 84
Injector Mounting Kit (Single): 34 Sequential Display Unit: 83
Injector Retaining Clip: 34 H
Pressure Damper Harness
SP01: 48
Alpha Plus
Pressure Regulators
A-Series Two Injector Static Harness: 12
10.0 Bar
General 4 Cylinder Harness (Replaces
RPF17/04: 47
9990205300): 12
2.5 Bar
General 4 Cylinder Static Engine Harness
100Li/Hr 1 x 14mm ‘O’ Ring & 1 x 8mm
(Race): 12
Push-on: 44
60Li/Hr 2 x 8mm Push-on: 44 General 4 Cylinder Static Vehicle
RP42: 44 Harness (Race): 12
RP54: 45 General 6 Cylinder Static Harness: 12
RP7: 44 General 8 Cylinder Harness: 12
RPM36: 46 Kit Car Harness 4 Cylinder (Ford Zetec
3.0 Bar 1.8 & 2.0 Only): 12
100Li/Hr 1 x 14mm ‘O’ Ring & 1 x 8mm Porsche 911 6 Cylinder Harness: 12
Push-on: 44 V8 Distributor Harness: 12
60Li/Hr 1 x 14mm ‘O’ Ring & 1 x 8mm Ignition Only
Push-on: 44 Feed Harness (Ignition Only): 12
60Li/Hr 2 x 8mm Push-on: 44 Ford Zetec Static Harness: 12
RP1: 44 General 4 Cylinder Static Harness: 12
RP12: 44 Vauxhall/Opel XE Distributor Harness: 12
RP19: 44 Vauxhall/Opel XE Static Harness: 12
RP9: 44
RPM40: 46 I
3.5 Bar Ignition
150Li/Hr 1 x 14mm ‘O’ Ring & 1 x 6mm Ballast Resistor
Push-on: 44 1.0 Ohm: 60
150Li/Hr 1 x 14mm ‘O’ Ring & 1 x 8mm CD Ignition Kit: 52
Push-on: 44 Coil & Module
150Li/Hr 2 x 8mm Push-on: 44
Assembly (AEI 600A): 54
150Li/Hr 3 x 8mm Push-on: 44
BKL3B Ignition Module (No Heatsink): 53
RP17: 44
RP21: 44 Ignition Module: 53
RP22: 44 Plug Top
RP8: 44 BAE 700 AK: 59
90
Index
BMW: 59 K-Series 16v (45 DCOE): 21
Spark Plug Leads Vauxhall/Opel
Distributor Ecotec 1.6 16v (40 DCOE): 21
Peugeot/Citroën 1.9 8v: 62 Ecotec 1.6 16v (7°) (40 DCOE): 21
Renault 19 1.8 16v: 62 Ecotec 2.0 16v (45 DCOE): 21
Rover A-Series: 62 XE 2.0 16v (45 DCOE): 21
Static VW
Peugeot/Citroën 1.6 8v & 1.9 8v: 62 Golf 1.8/2.0 16v, Long (45 DCOE): 21
WIC016 Golf 1.8/2.0 16v, Short (45 DCOE): 21
Ford 1.6 CVH: 62
Ford X-Flow Static 1.3, 1.6 & 1.7: 62 L
Ford Zetec 1.6 16v, 1.8 16v & 2.0 16v: Lambda
62 Lambda Display System (Large): 81
WIC062 Lambda Display System (Small): 81
Ford Pinto 1.6/2.0 & Ford X-Flow 8v Lambda Sensor (Alpha Wiring Harnesses):
Static: 62 75
Longitudinally Mounted A-Series: 62
Lambda Sensor (OE fitment): 75
Normally Aspirated Cosworth: 62
Peugeot/Citroën XU9 1.6 8v & 1.9 8v: Lambda Sensor For Lambda Display
62 System: 81
Rover A-Series: 62 Lambda Sensor Mounting Boss: 75, 81
Vauxhall/Opel Ecotec 2.0 16v: 62 Lambda Sensor Mounting Boss Blanking
WIC062 & Distributor Plug: 75, 81
W 1.8 8v & 16v: 62 P
WIL134 & Distributor
Vauxhall/Opel XE 2.0 16v: 62 Part Number
Standard Coil 1006: 25
BAE 209: 55 3717000102: 72
Double Ended Ignition Coil (Std HT Post, 4156505000: 72
Packard Connector) (BAE 800AK): 56 4156505100: 72
Double Ended Ignition Coil (VW HT Post, 4504814900: 29
Minitimer Connector) (BAE 800EK): 56 4761501101: 34
Static Coils 5284000101: 24
4 Cylinder 5284001200: 24
Ford Zetec 4 Cylinder (3 Pin 5284003300: 24
Connector): 57 5284003400: 24
General 4 Cylinder (4 Pin Connector) 9500005400: 85
(BAE 040: 57
9555001900: 85
General 4 Cylinder (Bosch): 58
WIC062 Coil Bracket: 58 9555500100: 85
6 Cylinder 9555500200: 85
Bosch: 61 9555519600: 85
Inertia Switch 9555520900: 85
Connector Conversion Kit: 51 9555523800: 85
Inertia Switch: 51 9555523900: 85
Inlet Manifolds 9555524000: 85
Ford 9555524200: 85
CVH 8v (45 DCOE): 21 9555524300: 85
Pinto 8v (45 DCOE): 21 9555530100: 85
X-Flow 8v (40 DCOE): 21 9555540200: 85
Zetec 1.6,1.8,2.0 16v, Long (45 DCOE): 9555552200: 85
21 9800099900: 79
Zetec 1.6,1.8,2.0 16v, Short (45 DCOE): 9800100000: 79
21 9800100600: 79
Peugeot/Citroën 9802215000: 79
XU9 1.9 8v (40 DCOE): 21 9990001200: 34, 49
XU9 1.9 8v (45 DCOE): 21 9990008100: 49
Rover 9990009100: 49
K-Series 16v (40 DCOE): 21 9990009400: 49
91
Index
9990041100: 50 9990139100: 40
9990041200: 50 9990139200: 40
9990043000: 50 9990139500: 69
9990043400: 72 9990139600: 72
9990045000: 50 9990140400: 80
9990048100: 50 9990141400: 69
9990048200: 50 9990141600: 49
9990048300: 50 9990141700: 49
9990048400: 50 9990144300: 69
9990052200: 50 9990146400: 74
9990062600: 50 9990148900: 34
9990070700: 50 9990149900: 30
9990083500: 50 9990150000: 30
9990087600: 50 9990151200: 69
9990089700: 50 9990152500: 14
9990095700: 50 9990152600: 14
9990097000: 50 9990152700: 65
9990098600: 13 9990154600: 68
9990098900: 13 9990154700: 43
9990100400: 22 9990154800: 69
9990101000: 50 9990155200: 13
9990110700: 72 9990157900: 13
9990119200: 69 9990159400: 42
9990120000: 18 9990163800: 69
9990120100: 18 9990164300: 69
9990120200: 18 9990166200: 52
9990120300: 18 9990166400: 13
9990120400: 18 9990166500: 13
9990120500: 18 9990166600: 13
9990120600: 17, 18 9990166700: 13
9990120700: 18 9990166800: 13
9990121400: 15 9990166900: 13
9990121500: 15 9990167000: 13
9990121600: 15 9990167100: 73
9990121700: 15 9990172100: 26
9990121800: 22 9990173800: 40
9990122300: 34 9990175600: 13
9990122900: 16 9990175700: 13
9990123300: 29 9990178900: 34
9990123400: 29 9990179400: 14
9990124400: 29 9990180200: 50
9990124500: 29 9990180500: 12
9990125500: 50 9990180600: 14
9990125600: 50 9990180700: 14
9990125700: 50 9990181200: 14
9990125800: 50 9990181300: 14
9990126900: 14 9990181700: 13
9990127000: 14 9990181800: 14
9990127100: 14 9990181900: 14
9990130200: 43 9990182100: 14
9990130300: 43 9990188500: 13
9990130400: 43 9990188900: 22
9990135500: 74 9990189000: 18
9990135800: 50 9990189100: 18
9990137400: 14 9990189200: 18
9990138900: 40 9990189300: 18
92
Index
9990189700: 29 9990268600: 35
9990191000: 40 9990268700: 49
9990191700: 29 9990268800: 49
9990192700: 28 9990268900: 49
9990193000: 18 9990272400: 12
9990193100: 18 9990272500: 12
9990193200: 18 9990272600: 12
9990193300: 18 9990273600: 49
9990195600: 60 9990273700: 49
9990200700: 75, 81 9990274100: 49
9990200800: 75, 81 9990274500: 84
9990201500: 13 9990276700: 76
9990202800: 78 9990277700: 85
9990204700: 13 9990283900: 12
9990204800: 13 9990284400: 13
9990205600: 78 9990287100: 12
9990205700: 51 9990287200: 12
9990206500: 14 9990289900: 70
9990206600: 14 9990290000: 12
9990206700: 14 9990290200: 31
9990206900: 14 9990291400: 71
9990208300: 14, 51 9990291500: 71
9990220600: 78 9990291600: 70
9990221600: 14 9990293500: 12
9990224200: 40 9990295600: 71
9990224500: 65 9990295700: 71
9990224800: 12 9990295800: 58
9990225000: 12 9990297900: 8
9990225400: 12 9990298200: 12
9990226000: 34 9990298300: 12
9990226100: 7 9990298700: 26, 35
9990230300: 14 9990298800: 23
9990230400: 14 AFS-1: 81
9990232400: 15 AFS-2: 81
9990232500: 15 AH801: 24
9990232600: 15 AH802: 24
9990232700: 15 AH813: 24
9990235400: 22 AH814: 24
9990240400: 70 AH815: 24
9990241500: 84 AH841: 24
9990241600: 14 AH851: 24
9990241700: 14 AIL053: 62
9990241800: 14 AIL064: 62
9990241900: 14 AIL076: 62
9990249600: 76 AIL085: 62
9990249700: 76 AIL095: 62
9990250300: 76 AIL170: 62
9990252700: 22 AIL174: 62
9990255000: 76 AIL188: 62
9990255100: 76 AIL195: 62
9990259400: 34 AIL214: 62
9990261500: 23 AIL232: 62
9990261600: 76 AIL251: 62
9990266000: 31 AIL294: 62
9990266800: 31 ALS331: 75
9990268500: 35 ARL1: 82
93
Index
CR-01601: 25 MM5700: 21
CR-05203: 25 PI042: 7
JRW514: 25 PI043: 7
JRW515: 25 PI150: 8
JRW516: 25 T020: 78
JRW516/ATS: 25 T022: 78
K20002: 9 T024: 78
K20003: 9 T050: 83
K20013: 9 T100: 77
K97013: 11 TE13710: 79
K97014: 11 TE13716: 80
K97015: 11 V804440L2: 20
K97016: 11 V804440PL: 20
K97017: 11 V804440PR: 20
K97018: 11 V804440R2: 20
K97019: 11 V804445L2: 20
K97025: 11 V804445PL: 20
K97026: 11 V804445PR: 20
K97027: 11 V804445R2: 20
K97028: 11 V80450LS: 19
K98003: 9 V80450RS: 19
K99001: 10 V80452LS: 19
K99002: 10 V80452RS: 19
K99004: 10 V804540L: 19
K99005: 10 V804540R: 19
K99006: 10 V804542L: 19
K99007: 10 V804542R: 19
K99008: 10 WAS008: 65
K99009: 10 WAS009: 63
K99010: 9 WAS011: 63
K99011: 9 WCM016: 54
K99012: 9 WFD001: 48
K99013: 9 WFF042: 40
K99016: 9 WFF213: 40
K99018: 9 WFF214: 41
K99019: 9 WFI005: 32
K99020: 10 WFI023: 33
K99021: 10 WFI024: 33
LP 1000: 26 WFI191: 32
LP 2000: 26 WFI192: 32
LP 3000: 27 WFI193: 32
LP 4000: 27 WFI194: 33
LP 7000: 27 WFI195: 33
MM4242B: 21 WFI196: 33
MM4270B: 21 WFP093: 38
MM42806B: 21 WFP501: 36
MM44240A: 21 WFP502: 36
MM4980A: 21 WFP503: 39
MM4980B: 21 WFP700: 37
MM5000: 21 WFR024: 46
MM5100: 21 WFR029: 46
MM5200: 21 WFR034: 45
MM5300: 21 WFR037: 44
MM5400: 21 WFR040: 44
MM5500: 21 WFR043: 46
MM5600: 21 WFR044: 44
94
Index
WFR045: 44 Ø8: 50
WFR046: 44 Ø8 - Ø4 - Ø8: 50
WFR047: 44 Ø8 - Ø6 - Ø8: 50
WFR048: 46 ‘Y’ Connector
WFR049: 44 Ø14: 50
WFR050: 44 Ø16: 50
WFR052: 44 Ø4: 50
WFR053: 44 Ø6 - Ø8 - Ø6: 50
WFR500: 47 Ø8: 50
WFR501: 47 Elbow Connector
Ø12: 50
WIC003: 55
Ø13: 50
WIC031: 56
Ø14: 50
WIC041: 59
Ø15: 50
WIC062: 57 Ø19: 50
WIC130: 56 Ø8 - M12 x 1.5: 50
WIC131: 59 Ø8 - M14 x 1.5: 50
WIC133: 57 Straight Connector
WIC134: 58 Ø12 - Ø8: 50
WIC135: 61 Ø8: 50
WID028: 72 Ø8 - M12 x 1.5: 50
WID029: 72 Ø8 - M14 x 1.5: 50
WIL013: 62 Ø8 - Ø6: 50
WIM081: 53 Potentiometer Mounting Kits
WIM082: 53 Carburettor
WLS330: 81 40/45 DCOE: 31
WLS331: 75 40/45 DHLA: 31
WMS013: 66 48 DCO SP: 31
WMS014: 66 Throttle Body
WMS019: 67 Potentiometer PF3B (CW): 30
WPU088: 68 Potentiometer PF4B (CCW): 30
WSS001: 68 Publicity Material
WSS002: 68 Alpha Windscreen Banner: 76
WSS003: 68 Large Alpha ‘Cut Out’ Decal: 76
WSS004: 68 Medium Alpha ‘Cut Out’ Decal: 76
WSS005: 68 Medium Alpha ‘Cut Out’ Decal (White
WSS006: 68 Reflective): 76
WSS022: 68 Medium Alpha ‘Cut Out’ Decal (White): 76
WSS026: 68 Medium Alpha Sticker: 76
WSS030: 68 Small Alpha ‘Cut Out’ Decal: 76
WSS032: 68 R
WSS051: 68 RPM Limiter: 82
WSS074: 68
WSS075: 68 S
WSS076: 68 Sensors
WSS077: 68 Air Pressure Sensors
WSS078: 68 APS02/03: 66
WTS104: 64 APS05/01: 66
WTS133: 64 PRT03/04: 67
WTS155: 64 Speed Sensors
WTS185: 63 Bracket: 68
WTS186: 63 Camshaft Phase Sensor (For Distributor
Plastic Hose Connectors Fitment): 68
Specific Vehicle
‘T’ Connector
Ford CFi Crank Sensor: 68
Ø15 - Ø8 - Ø15: 50 Ford Zetec 1.6 16v & 2.0 16v: 68
Ø16: 50 Rover K Series 1.4 16v: 68
Ø6: 50 Vauxhall/Opel XE 2.0 16v: 68
95
Index
VW Golf 2.0 8v & 16v - 1992 on: 68 Existing Cable): 27
Type 1 Twin Cable - DCOE (Cables Included):
SEN8D: 68 27
SEN8D3: 68 Twin Cable - Throttle Bodies (Cables
SEN8E: 68 Included): 27
SEN8L: 68 Top Mounting
SEN8V: 68 Pico Injector Clearance Kit: 26
Type 2 Single Cable - DCOE (For Use With
SEN8I3: 68 Existing Cable): 26
SEN8K: 68 Top Mounting Bracket: 26
SEN8LA: 68 Twin Cable - DCOE (Cables Included):
SEN8M: 68 26
SEN8X: 68 Twin DCNF
Temperature 40mm
Air L/H Potentiometer: 19
ATS04: 63 L/H Slave: 19
ATS05: 65 R/H Potentiometer: 19
ATS07: 63 R/H Slave: 19
Coolant 42mm
Ford Zetec Type: 64 L/H Potentiometer: 19
Vauxhall Type: 64 L/H Slave: 19
WTS05: 63 R/H Potentiometer: 19
WTS09: 63 R/H Slave: 19
T Twin DCOE
40mm
Throttle Bodies L/H Potentiometer: 18
Air Filter L/H Slave: 18
Air Intake Tube R/H Potentiometer: 18
40mm & 45mm: 22 R/H Slave: 18
48mm & 50mm: 22 45mm
Mounting Flanges L/H Potentiometer: 18
Mounting Flange Kit (13mm): 23 L/H Slave: 18
Mounting Flange Kit (25mm): 23 R/H Potentiometer: 18
Single Air Horn / Inlet Air Hose Adaptor: R/H Slave: 18
22 48mm
Twin Bore Air Filter Flange - 40mm and L/H Potentiometer: 18
45mm: 22 L/H Slave: 18
Twin Bore Air Filter Flange - 48mm: 22 R/H Potentiometer: 18
Mono R/H Slave: 18
40mm 50mm
L/H Potentiometer: 15 L/H Potentiometer: 18
L/H Slave: 15 L/H Slave: 18
R/H Potentiometer: 15 R/H Potentiometer: 18
R/H Slave: 15 R/H Slave: 18
45mm Twin IDF
L/H Potentiometer: 15 40mm
L/H Slave: 15 L/H Potentiometer: 20
R/H Potentiometer: 15 L/H Slave: 20
R/H Slave: 15 R/H Potentiometer: 20
Thottle Body Adjustment R/H Slave: 20
Cover Plate With Return Spring Adaptor: 45mm
28 L/H Potentiometer: 20
Throttle Levers L/H Slave: 20
Female R/H Potentiometer: 20
Mono/Twin Throttle Body Lever: 29 R/H Slave: 20
Male Trigger Discs
Mono Throttle Body Lever: 29 4 Cylinder
Twin Throttle Body Lever: 29 A-Series In-line: 69
Throttle Linkage BDR In-line: 69
Bottom Mounting General In-line: 69
Single Cable - DCOE (For Use With Mercedes 190E In-line: 69
96
Index
6 Cylinder
BMW In-line 6: 69
Porsche Flat 6: 69
8 Cylinder
Range Rover V8: 69
Rover V8: 69
Specific
Ford CVH Trigger Disc Kit: 71
Ford Pinto Trigger Disc Kit: 71
Ford X-Flow Trigger Disc Kit: 71
Peugeot/Citroën 1.6 & 1.9 Trigger Disc
Kit: 71
Rover A-Series Trigger Disc Kit: 71
Trigger Disc 36-1 Teeth
Mounting
Multi-slot: 70
Single Hole: 70
Triple Hole: 70

Catalogo Webcon Alpha

Uploaded by

Copyright:

Available Formats

Catalogo Webcon Alpha

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Catalogo Webcon Alpha

Uploaded by

Copyright:

Available Formats

Components Manual - Edition 4.

Alpha Performance Parts

Alpha Plus Engine Management System

In view of our policy of continuous improvement, the

STANDARD MOTOR PRODUCTS EUROPE LTD SHALL NOT BE

This guide contains information protected by copyright.

STANDARD MOTOR PRODUCTS EUROPE LIMITED

Product names mentioned herein are for identification

Standard Motor Products Europe Limited © 2001

ORIGINAL EQUIPMENT RPM SIGNAL INTERFACES

The first character specifies the O.E. RPM signal pattern:

* Special Order Only - Please Contact Alpha Group.

The second character specifies the number of cylinders:

Part Number Product Description

PI150 Alpha Ignition Only

Part Number Product Description

Each kit includes:

Typical Power Figures

Ford Zetec 2.0 16v Std 128 bhp (95kW)

Renault Clio 1.8 16v Std 137 bhp (102kW)

Vauxhall Ecotec 2.0 16v Std 132 bhp (98kW)

Vauxhall XE 2.0 16v Std 150 bhp (112kW)

VW 1.8 16v Std 139 bhp (104kW)

Peugeot/Citroën 1.9 8v Std 128 bhp (96kW)

Part Number Product Description

* Contact Alpha Group For Availability.

Each kit includes:

Typical Power Figures

Ford Zetec 2.0 16v Std 128 bhp (95kW)

Vauxhall XE 2.0 16v Std 150 bhp (112kW)

Peugeot/Citroën 1.9 8v Std 128 bhp (96kW)

Part Number Product Description

Part Number Product Description

Part Number ECU Type Product Description

Part Number Product Description

Illustrated: Left Hand Elbow 9990122900.

Part Number Product Description

Fuel connection cam be

45mm Left Hand

N.B. 2 injector mounting kits required per twin throttle body.

40mm LH Slave 40mm RH Pot.

Type Identification From This Side

Part Number Product Description

Part Number Product Description

Part Number Product Description

Zetec 2.0 16v

Choke Side/ Carburettor/

Part Number Product Description

Part Number Product Description

Length I/D O/D

* To be used with Air Filter Mounting Kit Part No. 9990261500

Alpha Throttle Body Top Mounting Linkage

Part Number Product Description

Alpha Throttle Body Underside Mounting Linkage

Part Number Product Description

Part Number Product Description

Part Number Product Description Type

Part Number Product Description

Logarithmic Throttle Potentiometer And Mounting Kit