PSXX OMS0007 B PDF

No.
PS※※-OMS0007-B
PRODUCT NAME
Digital Pressure Switch
MODEL / Series / Product Number
ZSE20(F)
ISE20
Table of Contents
Safety Instructions 2
Model Indication and How to Order 8
Summary of Product parts 10
Definition and terminology 11
Mounting and Installation 14
Installation 14
Piping 16
Wiring 17
Outline of Settings [Measurement mode] 19
Pressure Setting 20
3 Step Setting Mode 21
Simple Setting Mode 23
Function Selection Mode 25
Function selection mode 25
Default setting 25
F 0 Units selection function 27
F 1 Setting of OUT1 28
F 3 Digital filter setting 31
F 4 Auto-preset function 32
F 6 Fine adjustment of display value 34
F10 Sub display setting 35
F11 Display resolution setting 40
F80 Power saving mode 41
F81 Security code 42
F82 Input of line name 44
F90 Setting of all functions 45
F98 Output check 47
F99 Reset to default settings 48
Other Settings 49
Maintenance 53
Forgotten the security code 53
Troubleshooting 54
Specification 61
Specifications 61
Dimensions 63
-1-
No.PS※※-OMS0007-B
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of "Caution", "Warning" or "Danger".
They are all important notes for safety and must be followed in addition to International Standards
(ISO/IEC)*1), and other safety regulations.
*1) ISO 4414: Pneumatic fluid power -- General rules relating to systems.
ISO 4413: Hydraulic fluid power -- General rules relating to systems.
IEC 60204-1: Safety of machinery -- Electrical equipment of machines .(Part 1: General requirements)
ISO 10218-1992: Manipulating industrial robots -Safety.
etc.
Caution indicates a hazard with a low level of risk which, if not avoided, could
Caution result in minor or moderate injury.
Warning indicates a hazard with a medium level of risk which, if not avoided,
Warning could result in death or serious injury.
Danger indicates a hazard with a high level of risk which, if not avoided, will
Danger result in death or serious injury.
Warning
1. The compatibility of the product is the responsibility of the person who designs the
equipment or decides its specifications.
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications
based on necessary analysis and test results.
The expected performance and safety assurance of the equipment will be the responsibility of the
person who has determined its compatibility with the product.
This person should also continuously review all specifications of the product referring to its latest catalog
information, with a view to giving due consideration to any possibility of equipment failure when
configuring the equipment.
2. Only personnel with appropriate training should operate machinery and equipment.
The product specified here may become unsafe if handled incorrectly.
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
3. Do not service or attempt to remove product and machinery/equipment until safety is
confirmed.
1. The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
2. When the product is to be removed, confirm that the safety measures as mentioned above are
implemented and the power from any appropriate source is cut, and read and understand the specific
product precautions of all relevant products carefully.
3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety measures if the
product is to be used in any of the following conditions.
1. Conditions and environments outside of the given specifications, or use outdoors or in a place
exposed to direct sunlight.
2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
3. An application which could have negative effects on people, property, or animals requiring special
safety analysis.
4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using
a mechanical protective function, and periodical checks to confirm proper operation.
-2-
Safety Instructions
Caution
1.The product is provided for use in manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
specifications or a contract if necessary.
If anything is unclear, contact your nearest sales branch.
Limited warranty and Disclaimer/Compliance Requirements

The product used is subject to the following "Limited warranty and Disclaimer" and "Compliance
Requirements".
Read and accept them before using the product.
Limited warranty and Disclaimer

1. The warranty period of the product is 1 year in service or 1.5 years after the product is
delivered,whichever is first.2)
Also, the product may have specified durability, running distance or replacement parts.
Please consult your nearest sales branch.
2. For any failure or damage reported within the warranty period which is clearly our
responsibility, a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other
damage incurred due to the failure of the product.
3. Prior to using SMC products, please read and understand the warranty terms and
disclaimers noted in the specified catalog for the particular products.
2) Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to the use of the
vacuum pad or failure due to the deterioration of rubber material are not covered by the
limited warranty.
Compliance Requirements
1. The use of SMC products with production equipment for the manufacture of weapons of
mass destruction (WMD) or any other weapon is strictly prohibited.
2. The exports of SMC products or technology from one country to another are govemed by the
relevant security laws and regulation of the countries involved in the transaction. Prior to
the shipment of a SMC product to another country, assure that all local rules goveming that
export are known and followed.
Caution
SMC products are not intended for use as instruments for legal metrology.
Products that SMC manufactures or sells are not measurement instruments that are qualified by pattern
approval tests relating to the measurement laws of each country.
Therefore, SMC products cannot be used for business or certification ordained by the measurement laws of
each country.
-3-
Operator
This operation manual is intended for those who have knowledge of machinery using pneumatic
equipment, and have sufficient knowledge of assembly, operation and maintenance of such
equipment. Only those persons are allowed to perform assembly, operation and maintenance.
Read and understand this operation manual carefully before assembling, operating or providing
maintenance to the product.
■Safety Instructions
Warning
■Do not disassemble, modify (including changing the printed circuit board) or repair.
An injury or failure can result.
■Do not operate the product outside of the specifications.

Do not use for flammable or harmful fluids.
Fire, malfunction, or damage to the product can result.
Verify the specifications before use.
■Do not operate in an atmosphere containing flammable or explosive gases.

Fire or an explosion can result.
This product is not designed to be explosion proof.
■Do not use the product in a place where static electricity is a problem.
Otherwise it can cause failure or malfunction of the system.
■If using the product in an interlocking circuit:

Provide a double interlocking system, for example a mechanical system
Check the product regularly for proper operation
Otherwise malfunction can result, causing an accident.
■The following instructions must be followed during maintenance:

Turn off the power supply
Stop the air supply, exhaust the residual pressure and verify that the air is released before performing
maintenance
Otherwise an injury can result.
-4-
Caution
■Do not touch the terminals and connectors while the power is on.
Otherwise electric shock, malfunction or damage to the product can result.
■After maintenance is complete, perform appropriate functional inspections and leak tests.
Stop operation if the equipment does not function properly or there is a leakage of fluid.
When leakage occurs from parts other than the piping, the product might be faulty.
Disconnect the power supply and stop the fluid supply.
Do not apply fluid under leaking conditions.
Safety cannot be assured in the case of unexpected malfunction.
■NOTE
○Follow the instructions given below when designing, selecting and handling the product.
●The instructions on design and selection (installation, wiring, environment, adjustment, operation,
maintenance, etc.) described below must also be followed.
Product specifications
Use the specified voltage.
Otherwise failure or malfunction can result.
Do not exceed the specified maximum allowable load.
Otherwise it can cause damage or shorten the lifetime of the Pressure switch.
Design the product to prevent reverse current when the circuit is opened or the product is forced to operate for
operational check.
Reverse current can cause malfunction or damage to the product.
Input data to the Pressure switch is not deleted, even if the power supply is cut off.
(Writing time: 10,000 times, Data duration: 20 years after power off)
Use the clean air.
This can cause operating failure.
If compressed air containing condensate is used, install an air dryer or drain catch before the filter and perform
drainage regularly.
If drainage is not performed regularly and condensate enters the secondary side, it can cause operating failure of
pneumatic equipment.
If regular drainage is difficult, the use of a filter with an auto drain is recommended.
Applicable fluid is air, inert gases and incombustible gases.
Do not use a fluid containing chemicals, synthetic oils including organic solvent, salt and corrosive gases.
Otherwise, damage to the product and malfunction can result.
Check the details of the specifications before using.
Use the specified measurement flow rate and operating pressure.
Otherwise it can cause damage to the pressure switch or inability to measure correctly.
Reserve a space for maintenance.
Allow sufficient space for maintenance when designing the system.
-5-
●Product handling
Installation
Tighten to the specified tightening torque.
If the tightening torque is exceeded the mounting screws and brackets may be broken.
If the tightening torque is insufficient, the product can be displaced and loosen the mounting screws.
Do not apply excessive stress to the product when it is mounted with a panel mount.
Otherwise damage to the product and disconnection from the panel mount can result.
Be sure to ground terminal FG when using a commercially available switch-mode power supply.
Do not drop, hit or apply shock to the Pressure switch.
Otherwise damage to the internal parts can result, causing malfunction.
Do not pull the lead wire forcefully, not lift the product by pulling the lead wire. (Tensile force 35 N or less)
Hold the body when handling to avoid the damage of the Pressure switch which lead to cause the failure and malfunction.
For piping of the Pressure switch, hold the piping with a spanner on the metal part of the piping (Piping
attachment).
Holding other part with spanner leads to damage the Pressure switch.
Eliminate any dust left in the piping by air blow before connecting the piping to the product.
Otherwise it can cause damage or malfunction.
Do not insert metal wires or other foreign matter into the pressure measurement port.
It can damage the pressure sensor causing failure or malfunction.
Never mount a Pressure switch in a location that will be used as a foothold.
The product may be damaged if excessive force is applied by stepping or climbing onto it.
If the entering of foreign material to the fluid is possible, install and pipe the filter or the mist separator to
the inlet to avoid failure and malfunction.
Wiring
Do not pull the lead wires.
In particular, never lift a Pressure switch equipped with fitting and piping by holding the lead wires.
Otherwise damage to the internal parts can result, causing malfunction or to be off the connector.
Avoid repeatedly bending or stretching the lead wire, or placing heavy load on them.
Repetitive bending stress or tensile stress can cause the sheath of the wire to peel off, or breakage of the wire.
If the lead wire can move, fix it near the body of the product.
The recommended bend radius of the lead wire is 6 times the outside diameter of the sheath, or 33 times the
outside diameter of the insulation material, whichever is larger.
Replace the damaged lead wire with a new one.
Wire correctly.
Incorrect wiring can break the Pressure switch.
Do not perform wiring while the power is on.
Otherwise damage to the internal parts can result, causing malfunction.
Do not route wires and cables together with power or high voltage cables.
Otherwise the product can malfunction due to interference of noise and surge voltage from power and high voltage
cables to the signal line. Route the wires (piping) of the product separately from power or high voltage cables.
Confirm proper insulation of wiring.
Poor insulation (interference from another circuit, poor insulation between terminals, etc.) can lead to excess
voltage or current being applied to the product, causing damage.
Design the system to prevent reverse current when the product is forced to operate for operational check.
Depending on the circuit used, insulation may not be maintained when operation is forced, allowing reverse current
to flow, which can cause malfunction and damage the product.
Keep wiring as short as possible to prevent interference from electromagnetic noise and surge voltage.
Do not use a cable longer than 10 m.
Wire the DC(-) line(blue) as close as possible to the power supply.
Environment
Do not use the product in area that is exposed to corrosive gases, chemicals, sea water, water or steam.
-6-
Do not use in a place where the product could be splashed by oil or chemicals.
If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent,
even for a short time, it may be adversely affected (damage, malfunction, or hardening of the lead wires).
Do not use in an area where surges are generated.
If there is equipment which generates a large amount of surge (solenoid type lifter, high frequency induction
furnace, motor, etc.) close to the Pressure switch, this may cause deterioration or breakage of the internal circuit of
the Pressure switch. Avoid sources of surge generation and crossed lines.
Do not use a load which generates surge voltage.
When a surge-generating load such as a relay or solenoid is driven directly, use a Pressure switch with a built-in
surge absorbing element.
The product is CE marked, but not immune to lightning strikes. Take measures against lightning strikes
in the system.
Mount the product in a place that is not exposed to vibration or impact.
Prevent foreign matter such as remnant of wires from entering the Pressure switch.
Take proper measures for the remnant not to enter the Pressure switch in order to prevent failure or malfunction.
Do not use the product in an environment that is exposed to temperature cycle.
Heat cycles other than ordinary changes in temperature can adversely affect the inside of the product.
Do not expose the product to direct sunlight.
If using in a location directly exposed to sunlight, shade the product from the sunlight.
Keep within the specified fluid and ambient temperatures range.
The fluid and ambient temperatures should be -5 to 50 °C. Operation under low temperature (5 °C or less) leads to
cause damage or operation failure due to frozen moist in the fluid or air.
Protection against freezing is necessary. Air dryer is recommended for elimination of drain and water.
Avoid sudden temperature change even within specified temperature.
Do not operate close to a heat source, or in a location exposed to radiant heat.
Otherwise malfunction can result.
Adjustment and Operation

Turn the power on after connecting a load.
Otherwise it can cause excess current causing instantaneous breakage of the Pressure switch.
Do not short-circuit the load.
Although error is displayed when the Pressure switch load is short circuit, generated excess current lead to cause
the damage of the Pressure switch.
Do not press the setting buttons with a sharp pointed object.
It may damage the setting buttons.
If using the product to detect very small pressure rates, warm up the product for 10 to 15 minutes first.
There will be a drift on the display of approximate 1% immediately after the power supply is turned on, within 10
minutes.
Perform settings suitable for the operating conditions.
Incorrect setting can cause operation failure.
For details of each setting, refer to page 19 to 52 of this manual.
Do not touch the LCD during operation.
The display can vary due to static electricity.
Maintenance
Turn off the power supply, stop the supplied air, exhaust the residual pressure and verify the release of
air before performing maintenance.
There is a risk of unexpected malfunction.
Perform regular maintenance and inspections.
There is a risk of unexpected malfunction.
Perform drainage regularly.
If condensate enters the secondary side, it can cause operating failure of pneumatic equipment.
Do not use solvents such as benzene, thinner etc. to clean the Pressure switch.
They could damage the surface of the body and erase the markings on the body.
Use a soft cloth to remove stains. For heavy stains, use a cloth soaked with diluted neutral detergent and fully
squeezed, then wipe up the stains again with a dry cloth.
-7-
Model Indication and How to Order
-8-
○Accessories/Part numbers
If an option is required independently, order with the following part numbers.
Items Part No. Remarks
Bracket A ZS-46-A1 Self tapping screws: Nominal size 3 x 8L (2 pcs)
Bracket B ZS-46-A2 Self tapping screws: Nominal size 3 x 8L (2 pcs)
Panel mount adapter ZS-46-B -
Panel mount adapter + Front protective
ZS-46-D -
cover
Lead wire with connector ZS-46-3L 3 cores, 2 m
Front protective cover ZS-27-01 -
R1/8 piping adapter ZS-46-N1 -
NPT1/8 piping adapter ZS-46-N2 -
-9-
Summary of Product parts
○Names of individual parts
Operation light: Displays the switch operating condition.

LCD display: Displays the current status of pressure, setting mode, selected display units and error code.
4 types of display can be selected for the main display: Single colour of constant red or
green; or switching from red to green or green to red corresponding to the output.
The indication for the sub display is orange.
button: Increases mode and ON/OFF set values.
button: Decreases mode and ON/OFF set values.
button: Press this button to change mode and to confirm settings.
Unit display: Indicates the units currently selected. (Only for display units of kPa and MPa.)
-10-
■Definition and terminology
Term Definition
A Performs pressure setting automatically by detecting the increase and
decrease in pressure. For example, if this function is used for a suction test,
Auto-preset
the pressure setting will be completed by performing suction and release of
the workpiece.
B Shows the minimum pressure from when the power was supplied to the
Bottom value display (mode)
current time.
C The problem of the switch output turning ON and OFF repeatedly around the
Chattering
set value at high frequency due to the effect of pulsation.
A function to delay the response time of switch output in order to prevent
Chattering prevention function
chattering.
D The setting time from when the pressure applied to the pressure switch
reaches the set value, to when the ON-OFF output actually begins working.
Delay time Delay time setting can prevent the output from chattering.
The response time indicates when the set value is 90% in relation to the step
input.
Shows how precisely the pressure can be displayed or set by the digital
digit (Min. setting unit) pressure switch. When 1 digit = 1 kPa, the pressure is displayed in increments
of 1 kPa, e.g., 1, 2, 3, …, 99, 100.
Function to add digital filtering to the fluctuation of pressure value. Smooth the
fluctuation of displayed value for sharp start up or fall of the pressure.
When the function is valid, digital filtering is reflected to the ON/OFF of the
Digital filter
switch output.
Output chattering or flicker in the measurement mode display can be reduced
by setting the digital filter.
Shows The maximum deviation between the displayed pressure value and
Display accuracy
the true pressure.
Indicates the colour of the number of digital display. Always green, always
Display colour red, green (switch OFF)  red (switch ON), red (switch OFF)  green (switch
ON) are available.
Indicate in how many the rated pressure range can be divided to display.
Display resolving power (Example: When the value can be displayed down to 0.001 MPa for the
product for 0 to 1 Mpa, the resolution is 1/1000)
Displayed pressure value can be adjusted within the range of 5%R.D. (5%
Display value fine adjustment of displayed value). It is used if the true pressure value is known, or to
(function) eliminate differences between the displayed values of different instruments
that are measuring the same pressure.
E The code number displayed, identifying the error detected by the

Error displayed self-diagnosis function of the pressure switch.
Refer to "Error indication function" on page 60 for details of the errors.
Switches the switch output to ON/OFF when an error is displayed.

Error output Refer to "List of output modes" on page 30 for operating conditions.
Refer to "Error indication function" on page 60 for details of the errors.
-11-
Term Definition
F Abbreviation of full span and full scale; difference between the minimum and
maximum rated pressure values. means the maximum fluctuation range of
F.S. the pressure switch rated value.
(full span/full scale) For example, when the rated pressure range is -0.100 to 1.000 [MPa]:
F.S. = 1.000 - (-0.100) = 1.100 [MPa]
(Reference: 1%F.S. = 1.100 x 0.01 = 0.011 [MPa])
Fine adjustment mode Refer to "Display value fine adjustment (function)".
Fluid contact part (or wetted Part of the pressure switch which contacts detected fluid. Pressure sensor,
part) seal and fitting are included.
A mode in which setting of functions is performed. It is a separate menu from

the pressure setting. If any function settings need to be changed from the
factory default, each setting can be selected with "F". The setting items are:
Function selection mode
display colour, operation mode, output type, digital filter, display resolution,
display value fine adjustment, use of auto preset, use of power saving mode,
security code, etc.
H Difference between the points at which the pressure switch is turned ON and
Hysteresis
OFF.
Hysteresis mode Refer to the "List of output modes" on page 30.
I Insulation resistance of the product. The resistance between the electrical
Insulation resistance
circuit and the case.
K Function that prevents changes to the settings of the Pressure switch
Key-lock function
(disables button operation).
M Manual pressure setup without using auto preset.
Manual setting This term is used to distinguish between manual and auto preset pressure
setup.
Maximum applied voltage The maximum voltage that can be connected to the output of an NPN device.
The maximum current that can flow to the output (output line) of the switch
Maximum load current
output.
Operating condition in which pressure is being detected and displayed, and
Measurement mode
the switch function is working.
Min. setting unit Refer to "digit".
N One of the switch output types. In hysteresis mode the switch output is turned
ON when pressure equal to or greater than the switch output set value is
Normal output detected. In window comparator mode, the switch output is turned ON when
pressure between the switch output set values (P1L to P1H) is detected.
(Refer to the "List of output modes" on page 30.)
O Operation light A light that turns on when the switch output is ON.
Operation mode Either hysteresis mode or window comparator mode can be selected.
The operation principle of the switch output. Normal output and reverse output
Output style can be selected.
Please refer to the" List of output modes" on page 30 operating conditions.
-12-
Term Definition
P Shows the maximum pressure from when the power was supplied to the
Peak value display (mode)
current time.
The diameter of the connecting part of the switch for connecting with the
Port size
object to be measured.
Operating mode in which the digital display turns off and power consumption
Power saving mode
is reduced.
The set pressure value that determines the point at which the pressure switch
Pressure setting
turns ON and OFF.
Pressure limit that if exceeded will result in mechanical and/or electrical
Proof pressure
damage to the product.
R Current read value
For example, when the display value is 1.000[MPa], 5%R.D. is 5% of
R.D.
1.000[MPa], which becomes 0.05[MPa]. When the display value is
0.800[MPa], 5%R.D. is 5% of 0.800[MPa], which becomes 0.04[MPa].
The pressure range within which the product will meet all published
specifications.
Rated pressure range
Values outside of this range can be set as long as they are within the set
pressure range, but the specifications cannot be guaranteed.
Variation in repeated measurement of pressure display or ON-OFF output

Repeatability
point when the pressure changes at 25 centigrade.
The difference between the ideal ON voltage and the actual voltage when the
Residual voltage
switch output is on. Varies with load current. Ideally should be 0 V.
Resolution Refer to "Display resolution".
One of the switch output types. In hysteresis mode the switch output is turned
ON when pressure less than or equal to the switch output set value is
Reversed output detected. In window comparator mode, the switch output is turned ON when
pressure is outside the switch output set values (n1L to n1H) is detected.
Ripple A type of chattering.
S Set pressure range The pressure range that can be set for switch output.
Switch output Sometimes referred to as "ON-OFF output".
U A function to change the units in which the measured pressure value is
displayed. The display units can only be changed if the product is equipped
Units selection function this function. It is not possible to purchase the product with this function if the
product is used in Japan.
The product for Japan is displayed in SI only.
W An operating mode in which the switch output is turned on and off depending
Window comparator mode on whether the flow is inside or outside the range of two set values.
A measure of the product’s resistance to a voltage applied between the

electrical circuit and case. Durability in withstanding voltage. The product may
Withstand voltage
be damaged if a voltage over this value is applied.
(The withstand voltage is not the supply voltage used to power the product.)
Z Zero-clear function This function to adjust the displayed pressure to zero.
-13-
Mounting and Installation
■Installation
○Mounting with bracket
●Mount the bracket to the body with mounting screws (Self tapping screws: Nominal size 3 x 8L (2 pcs)),
then set the body to the specified position.
: Tighten the bracket mounting screws to a torque of 0.5±0.05 Nm.
Self tapping screws are used, and should not be re-used several times.
•Bracket A (Part No.: ZS-46-A1)
•Bracket B (Part No.: ZS-46-A2)
-14-
○Mounting with panel mount adapter
●Mount part (a) to the front of the body and fix it. Then insert the body with (a) into the panel until (a)
comes into contact with the panel front surface. Next, mount part (b) to the body from the rear and insert
it until (b) comes into contact with the panel for fixing.
•Panel mount adapter (Part No.: ZS-46-B)
Panel mount adapter + Front protective cover (Part No.: ZS-46-D)
: The panel mount adapter can be rotated through 90 degrees for mounting.
How to remove the panel mount adapter

●When removing the digital pressure switch with panel mount adapter from the installation, pull
it forward while expanding the hooks on each side as shown below.
If the panel mount adapter is pulled forward with the hook caught, the product and the
adapter may be damaged.
-15-
■Piping
○Tightening the connection thread
●For connecting to the body (piping specification: -M5)
After hand tightening, apply a spanner of the correct size to the spanner flats of the piping body, and
tighten with a 1/6 to 1/4 rotation.
As a reference, the tightening torque is 1 to 1.5 Nm.
(When replacing the piping adapter ZS-46-N, tighten it using the same method.)
●Piping specification: -01, -N01

After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten
with 2 to 3 rotations.
As a reference, the tightening torque is 3 to 5 Nm.
When tightening, do not hold the Z/ISE20 body with a spanner.
-16-
■Wiring
○Wiring connections
●Connections should be made with the power supply turned off.
●Use a separate route for the product wiring and any power or high voltage wiring. Otherwise, malfunction
may result due to noise.
●If a commercially available switching power supply is used, be sure to ground the frame ground (FG)
terminal. If the switching power supply is connected for use, switching noise will be superimposed and it
will not be able to meet the product specifications. In that case, insert a noise filter such as a line noise
filter/ferrite between the switching power supplies or change the switching power supply to the series
power supply.
○How to use connector

Connector attachment/detachment
●When connecting the connector, insert it straight onto the pins, holding the lever and connector body, and
lock the connector by pushing the lever hook into the concave groove on the housing.
●To detach the connector, remove the hook from the groove by pressing the lever downward, and pull the
connector straight out.
Connector pin numbers
-17-
○Internal circuit and wiring examples
Z/ISE20(F)-□-□-□-□□□
Output specification
-N
NPN open collector 1 output
Max. 28 V, 80 mA
Residual voltage: 1 V or less
-P
PNP open collector 1 output
Max. 80 mA
Residual voltage: 1 V or less
-18-
Outline of Settings [Measurement mode]
Power is supplied.
The product code is displayed for approximately 3 sec. after supplying power.
: Within approximately 0.2 second after power-on, the switch starts.
[Measurement mode]
Detects the pressure after power is supplied, and indicates the display and switch
operating status. This is the basic mode; other modes should be selected for set-point
changes and other function settings.
Measurement mode screen
Sub display
In measurement mode, the display of the sub display can be temporarily changed by pressing the
or buttons.
: One arbitrary display mode can be added to the sub display by setting the [F10] sub display setting.
If the sub display is switched during the arbitrary display setting, the display will be returned to the arbitrary display 30
seconds later. (The default setting does not include arbitrary display.)
Press the Press the

Press the
button button
button
between 1 between 3
once.
and 3 sec. and 5 sec.
Set either of set Select the set Change the Other Settings
value or value, hysteresis function •Zero-clear
hysteresis. and delay time. settings. function
(3 step setting (Simple setting (Function selection •Key-lock
mode) mode) mode) function
(Refer to page 21.) (Refer to page 23.) (Refer to page 25.) (Refer to page 49.)
: The outputs will continue to operate during setting.

: If a button operation is not performed for 3 seconds during the setting, the display will flash.
(This is to prevent the setting from remaining incomplete if, for instance, an operator were to leave during setting.)
: 3 step setting mode, simple setting mode and function selection mode settings are reflected each other.
-19-
Pressure Setting
Default settings
When the pressure exceeds the set value, the switch will be turned on. When the pressure falls below the set
value by the amount of hysteresis or more, the switch will be turned off. The default setting is to turn on the
pressure switch when the pressure reaches the centre of the atmospheric pressure and upper limit of the
rated pressure range. If this condition, shown to the below, is acceptable, then keep these settings.
●ISE20
Item Default setting
[P_1] Set value of OUT1 0.500 MPa
[H_1] Hysteresis of OUT1 0.050 MPa
●ZSE20
[P_1] Set value of OUT1 -50.5 kPa
[H_1] Hysteresis of OUT1 5.1 kPa
●ZSE20F
[P_1] Set value of OUT1 50.0 kPa
[H_1] Hysteresis of OUT1 5.0 kPa
Zero-clear of display
The display is reset to zero when the and buttons are pressed simultaneously for 1 second.
For the first operation, perform a zero-clear without pressure at measurement mode.
-20-
3 Step Setting Mode
3 step setting mode
In this mode, the set values can be input in just 3 steps.
Use this mode if the product is to be used straight away, after changing only the set values.
(The current pressure value is displayed on the main display.)
<Operation>
[3 step setting mode (hysteresis mode)]
In the 3 step setting mode, the set value (P_1 or n_1) and hysteresis (H_1) can be changed. Set the items
on the sub display (set value or hysteresis) with or button. When changing the set value, follow
the operation below. The hysteresis setting can be changed in the same way.
(1) Press the button once when the item to be changed is displayed on the sub display.
The set value on the sub display (right) will start flashing.
(2) Press the or button to change the set value.

The set value can be increased with button and can be reduced with button.
●Press the button once to increase the value by one digit, press and hold to continuously
increase.
●Press the button once to reduce the value by one digit, press and hold to continuously reduce.
●When the and buttons are pressed and held simultaneously for 1 second or longer, the
set value is displayed as [- - -], and the set value will be the same as the current pressure value
automatically (snap shot function (Refer to page 49.)). Afterwards, it is possible to adjust the value by
pressing the or button.
(3) Press the button to complete the setting.
-21-
The Pressure switch turns on within a set pressure range (from P1L to P1H) during window comparator
mode. Set P1L, the lower limit of the switch operation, and P1H, the upper limit of the switch operation and
WH1 (hysteresis) following the instructions given on page 21.
(When reversed output is selected, the sub display (left) shows [n1L] and [n1H].)
Please refer to the "List of output modes" on page 30 for the relationship between the set values and
operation.
: Setting of the normal/reverse output switching and hysteresis/window comparator mode switching are
performed with the function selection mode [F 1] Setting of OUT1.
-22-
Simple Setting Mode
<Operation>
[Simple setting mode (hysteresis mode)
In the simple setting mode, the set value, hysteresis and delay time can be changed while checking the
current pressure value (main display).
(1) Press and hold the button between 1 and 3 seconds in measurement mode. [SEt] is displayed
on the main display. When the button is released while in the [SEt] display, the current pressure value
is displayed on the main display, [P_1] or [n_1] is displayed on the sub display (left), and the set value
is displayed on the sub display (right) (Flashing).
(2) Change the set value with or button, and press the button to set the value. Then, the
setting moves to hysteresis setting. (The snap shot function can be used. (Refer to page 49.))
(3) Change the set value with or button, and press the button to set the value. Then, the
setting moves to the delay time of the switch output.
(The snap shot function can be used. (Refer to page 49.))
(4) Press the or button, the delay time of the switch output can be selected.
Delay time setting can prevent the output from chattering.
(5) Press the button for 2 seconds or longer to complete the OUT1 setting.
If the button is pressed for less than 2 seconds, the setting will be returned to P_1.
1: Selected items (1) to (4) become valid after pressing the button.
2: After enabling the setting by pressing the button, it is possible to return to measurement mode by pressing the
button for 2 seconds or longer.
3: When the output mode (refer to page 28) is set to error output or output OFF, the simple setting mode cannot be used.
(The setting changes to measurement mode by releasing the button when [SEt] is displayed.)
-23-
In the window comparator mode, set P1L, the lower limit of the switch operation, and P1H, the upper limit of
the switch operation, WH1 (hysteresis) and dt1 (delay time) following the instructions given on page 23.
(When reversed output is selected, the sub display (left) shows [n1L] and [n1H].)
Please refer to the "List of output modes" on page 30 for the relationship between the set values and
operation.
-24-
Function Selection Mode
■Function selection mode
In measurement mode, press the button between 3 and 5 seconds, to display [F 0]. Select to display
the function to be changed [F□□]. Press and hold the button for 2 seconds or longer in function
selection mode to return to measurement mode.
: Some products do not have all the functions. If no function is available or selected due to configuration of other functions, [- - -] is
displayed on the sub display (right).
■Default setting
The default setting is as follows.
If no problem is caused by this setting, keep these settings.
To change a setting, enter function selection mode.
●[F 0] Units selection function Page 27

Units specification Pressure range Default setting
ISE20 MPa
"Nil" or M
ZSE20(F) kPa
ISE20
P psi
ZSE20(F)
●[F 1] Setting of OUT1 Page 28

Item Explanation Default setting
Either hysteresis mode, window comparator mode, error output or
Output mode Hysteresis mode
output off can be selected.
Reversed output Selects which type of switch output is used, normal or reversed. Normal output
ISE20 : 0.500 MPa
Pressure setting Sets the ON and OFF point of the switch output. ZSE20 : -50.5 kPa
ZSE20F : 50.0 kPa
ISE20 : 0.050 MPa

Appropriate setting of the hysteresis will prevent the switch output
Hysteresis ZSE20 : 5.1 kPa
from chattering.
ZSE20F : 5.0 kPa
Delay time Delay time of the switch output can be selected. 1.5 ms or less
Output ON : Green
Display colour Select the display colour.
Output OFF: Red
-25-
●Other parameter settings
Item Page Default setting
[F 2] - No configurable items
[F 3] Digital filter setting Page 31 0 ms
[F 4] Auto-preset function Page 32 Not used
[F 5] - No configurable items
[F 6] Fine adjustment of display value Page 34 0%
[F10] Sub display setting Page 35 std (Standard)
[F11] Display resolution setting Page 40 1000-split
[F80] Power saving mode Page 41 OFF
[F81] Security code Page 42 OFF
[F82] Input of line name Page 44 AAAA
[F90] Setting of all functions Page 45 OFF
[F96] - No configurable items
[F97] - No configurable items
[F98] Output check Page 47 N/A (normal output)
[F99] Reset to default settings Page 48 OFF
-26-
■[F 0] Units selection function
This setting is only available for models with the units selection function.
The unit that can be displayed is different depending on the pressure range.
(kPa/MPa can still be selected if the product does not have the units selection function.)
<Operation>
Press the or button in function selection mode to display [F 0].
Press the button. Move on to display unit selection.
Display unit selection

Press the or button to select the display unit.
Press the button to set. Return to function selection mode.
[F 0] Units selection function completed
●Available display unit and minimum set value

Unit ZSE20F ZSE20 ISE20
MPa 0.001 0.001 0.001
kPa 0.1 0.1 1
kgf/cm2 0.001 0.001 0.01
bar 0.001 0.001 0.01
psi 0.02 0.01 0.1
InHg 0.1 0.1 -
mmHg 1 1 -
-27-
■[F 1] Setting of OUT1
Set the output mode of OUT1.
Output turns on when the pressure is greater than the set value. The default setting is to turn on the
pressure switch when the pressure reaches the centre of the atmospheric pressure and upper limit of the
rated pressure range.
Output ON lights in green and output OFF lights in red as default setting.
Please refer to the "List of output modes" on page 30 for the relationship between the set items and operation.
<Operation>
Press the button. Move on to output mode setting.
Output mode setting

Press the or button to select the required output mode.
Press the button to set. Move on to reversed output setting.
Reversed output setting

Press the or button to
select the reversed output.
[OFF] Output off is

selected
Press the
button to move on to
display colour setting.
Press the button to set. Move on to pressure setting.
Pressure setting
Set the pressure based on the [Err] Error output is
setting method on page 21. selected
Press the button
Hysteresis mode: [P_1] to move on to display
Window comparator mode: [P1L][P1H] colour setting.
"P" is changed to "n" as [P_1]  [n_1] when
reversed output is selected.
The snap shot function can be used.
(Refer to page 49.)
Press the button to set. Move on to hysteresis setting.

-28-
Hysteresis setting
Set the pressure referring to
the setting method on page 21.
Hysteresis mode: [H_1]

Window comparator mode: [WH1]
The snap shot function can be used. (Refer to page 49.)
Press the button to set. Move on to delay time setting.
Delay time setting

Set the delay time referring to the
setting method on page 23.
Press the button to set. Move on to display colour setting.
Display colour setting

Press the or button to select the display colour.
[F 1] Setting of OUT1 completed
1: Selected item becomes valid after pressing the button.

2: After enabling the setting by pressing the button, it is possible to return to the measurement mode by keeping pressing
the button for 2 seconds or longer.
-29-
●List of output modes
: Applicable errors are Er0, 4 to 6, 8, and 9.
If the point at which the switch output changes is outside of the set pressure range due to the selection
of normal or reversed output, the hysteresis value is automatically adjusted.
-30-
■[F 3] Digital filter setting
The Digital filter can be selected to filter the pressure measurement.
Output chattering or flicker in the measurement mode display can be reduced by setting the digital filter.
<Operation>
Press the button. Move on to digital filter setting.
Digital filter setting

Press the or button to select the digital filter.
[F 3] Digital filter setting completed
1: Each set value is a guideline for 90% response time.

2: Both the switch output and pressure display are affected. When only switch output needs to be affected, select the delay
time setting (page 23 and 29).
-31-
■[F 4] Auto-preset function
This function will automatically calculate and set the optimum pressure based on the actual operating
condition, when hysteresis mode has been selected.
<Operation>
Press the button. Move on to Auto-preset function.
Auto-preset function
Press the or button to select the auto-preset function.
[F 4] Auto-preset function completed
Press the button in measurement mode to perform the pressure setting.

Then, press the button again to change the pressure while the display is flashing.
(Refer to page 33 for details.)
-32-
●Auto-preset
When auto-preset is selected in function selection mode, the set value can be calculated and memorized
from the measured pressure. Repeating the suction and release of the workpiece to be set for several
times will automatically optimize the set value.
(1) Selection of auto-preset OUT1 mode

Press the button in measurement mode to display [AP1 REdY].
(If setting of OUT1 is not necessary, select [AP1 REdY], and then press
the and buttons simultaneously for 1 second or longer.
The display will move to measurement mode).
(2) Preparation of equipment for OUT1

Prepare the equipment for which the pressure of OUT1 is to be set.
(3) Setting of auto-preset for OUT1

Press the button, [AP1 RUn] will be displayed.
Measurement starts. Operate the device to change the pressure.
(If the and buttons are pressed simultaneously for 1 second or
longer while [AP1 RUn] is displayed, measurement will be stopped and
measurement mode will return).
(4) Complete setup.

Press the button to complete auto-preset mode. Then, measurement mode returns.
The settings in auto-preset will be as follows.

•Normal output •Reversed output
P_1 = A - (A - B)/4 n_1 = B + (A - B)/4 A = Maximum pressure
H_1 = (A - B)/2 H_1 = (A - B)/2 B = Minimum pressure
If setting is not necessary press the and buttons simultaneously for 1 second or longer.
-33-
■[F 6] Fine adjustment of display value
This function is to manually perform a fine adjustment of the displayed pressure value.
Pressure can be adjusted in the following range of 5%R.D.
<Operation>
Press the button. Move on to fine adjustment of display value.
Fine adjustment of display value

Press the or button to change adjustment rate.
When adjustment rate is changed, the pressure value after the

adjustment will be displayed on the main screen.
[F 6] Fine adjustment of display value completed
-34-
■[F10] Sub display setting
Change the display style of the sub display.
<Operation>
Press the or button in function selection mode to display [F10].
Press the button. Move on to sub display setting.
Sub display setting

Press the or button to select the display style for the
sub display.
When [dUAL] 2 value display is selected

When other than
Press the button to move on to sub
[dUAL] 2 value
display (left) setting.
display is selected
Press the button
to set.
Sub display (left) setting
Return to function
Set the sub display (left) from the selection list on page 36. selection mode.
Press the button to set. Move to sub display (right) setting.
Sub display (right) setting

Set the sub display (right) from the selection list on page 36.
[F10] Sub display setting completed
-35-
<Sub display>
•Standard
The Standard display function displays the items and values on the sub display.
The displayed item varies depending on the setting of the output mode. Select the displayed items by
pressing the or button in measurement mode.
(Hysteresis mode, error output, switch output off)
(Window comparator mode)
•2 value display
The 2 value display function displays the items listed below on the right and left side of the sub display.
List of items for selection

Sub display
Item Details Remarks
Left side Right side
When hysteresis mode is
( ) Set value for OUT1 hysteresis mode ○ ○
selected
When hysteresis mode is
OUT1 hysteresis mode ○ ○
selected
OUT1 Window comparator mode set value When window comparator
( ) ○ ○
(Lower side) mode is selected
OUT1 Window comparator mode set value When window comparator
( ) ○ ○
(Upper side) mode is selected
When window comparator
OUT1 window comparator mode ○ ○
mode is selected
Pressure peak value ○ x
Pressure bottom value x ○
Pressure display unit ○ ○
Rated pressure range ○ ○
OUT1 output mode/output style ○ x
String of random characters ○ ○
Display OFF ○ ○
-36-
Table showing the rated pressure range when RAnG is selected.
Pressure range Rated pressure Characters displayed on the sub display
Vacuum pressure -101.3 kPa
Compound pressure 100 kPa
Positive pressure 1 MPa
Table showing the output mode and output form of OUT1 when Md1 is selected.
Output mode Output style Display style
Normal output
Hysteresis mode
Reversed output
Normal output
Window comparator mode
Reversed output
Error output Normal/Reversed output
Switch output off -
When using the 2 value display function, 3 step setting is not available for the display.
(When setting 3 step, select each set value to be displayed by pressing the or button.)
When output operation mode is changed after selecting the 2 value display, the selected display items will
not be applicable and [- - -] will be displayed. In this case, select items for the 2 value display setting again.
-37-
•Level bar display
The Level bar display is a function used to visualize the pressure and the ON area for the switch output on
the sub display.
The display style varies depending on the setting of the output mode.
(In hysteresis mode or window comparator mode)
The threshold bar displaying the switch output ON area is displayed according to the table below, using the
output mode.
(During error output or when the output is off)
The threshold bar will not be displayed. Only the pressure value meter is displayed.
Output mode Output style Threshold bar display style
Normal output
Hysteresis mode
Reversed output
Normal output
Reversed output
Error output Normal/Reversed output No indication

Switch output off - No indication
The Level bar display resolution (pressure for one "O") varies depending on the output mode.
Output mode Display resolution

Hysteresis mode 1/10 of P_1(n_1)
Window comparator mode 1/4 of P1H–P1L(n1H–n1L)
Positive pressure, vacuum pressure: Rated maximum pressure - 1/7 of the
Error output atmospheric pressure
Compound pressure: Rated maximum pressure - 1/4 of the atmospheric pressure
Positive pressure, vacuum pressure: Rated maximum pressure - 1/7 of the

Switch output off atmospheric pressure
Compound pressure: Rated maximum pressure - 1/4 of the atmospheric pressure
-38-
During an error output or when the output setting is off, the pressure value meter at the atmospheric
pressure is displayed according to the table below.
Rated range Display at atmospheric pressure
Vacuum pressure
Compound pressure
Positive pressure
•Character string display

The Character string display function will display the specified characters on the sub display (right).
Character setting is performed using the function [F82] Input of line name.
•Display OFF
The Sub display is not displayed.
-39-
■[F11] Display resolution setting
This function is to change the pressure display resolution.
The flicker of the display can be reduced.
<Operation>
Press the button. Move on to display resolution setting.
Display resolution setting

Press the or button to select the display resolution.
[F11] Display resolution setting completed
: It may not be possible to change the resolution depending on the unit of pressure selected.
The units that allow display resolution to be selected are [MPa], [kPa(ZSE20(F) only)], [kgf/cm 2], [bar],
[psi] and [inHg]
(The units [kgf/cm2], [bar], [psi] and [inHg] can only be set when using a product with units selection
function.)
Page 27 [F 0] Units selection function
-40-
■[F80] Power saving mode
Power saving mode can be selected.
When selected and no buttons are pressed for 30 seconds, the pressure switch will shift to power saving
mode.
<Operation>
Press the button. Move on to power saving mode.
Power saving mode

Press the or button to select the power saving mode.
[F80] Power saving mode completed
In power saving mode, when buttons are pressed the display is normal, but if no buttons are
pressed for 30 seconds, it will revert to power saving mode. (Power saving is only enabled in
measurement mode)
During power saving mode, [ECo] will flash in

the sub display and the operation light is ON
(only when the switch is ON).
-41-
■[F81] Security code
The security code can be turned on or off and the security code can be changed when unlocked.
<Operation>
Press the button. Move on to security code.
Security code
Press the or button to select the setting of security code.
[oFF] (not use) is Press the button to set. Move on to security code checking.
selected
Press the
button to return to Security code checking
function selection
Press the or button to input the
mode.
security code on the sub display (right).
(The default setting is [000].) 
For instructions on how to enter the security code, refer to "How to input
and change the security code" on page 52.
If the security code entered is incorrect, [FAL] will be displayed, and the
security code must be entered again.
If the wrong security code is entered 3 times, [nG] is displayed and the
device returns to function selection mode.
Move on to security code changing.
-42-
Security code changing
Press the or button to input the changed
security code on the main display. 
For instructions on how to enter the security code,
refer to "How to input and change the security code"
on page 52.
After entry, the changed security code will flash by

pressing the button for 1 second.
(At this point, the changing of the security code is not
completed)
Return to the change of setting again by pressing the
or button.
Press the button for 1 second to set. Return to function selection

mode.
[F81] Security code completed
If the security code function is enabled, it is will be necessary to input a security code to release the
key-lock.
: If a key is not pressed for 30 seconds while entering the security code, function selection mode will return.
-43-
■[F82] Input of line name
Function to display the specified character string on the sub display.
To display in the measurement mode, select 2 value display [dUAL] or character string display [LinE] using
the setting on [F10] Sub display setting.
<Operation>
Press the button. Move on to input of line name.
Input of line name

Press the or button to input the line name displayed on the
sub display (right).
Press the button to make the next digit to the right flash. Input the
line name.
(The most significant digit flashes when the button is pressed at the least significant digit.)
The order of displayed characters is A  b  • • •  Y  (Z)  0  1  • • •  9  symbol 
space.
(Characters which can be displayed are different for 1 digit on the left and 3 digits on the right.)
Pressing the and button simultaneously adds/deletes the dot (decimal point).
The set line name flashes by pressing the button for 1 second or longer.
(At this point, the setting of the line name is not complete.)
[F82] Input of line name completed
•Characters which can be displayed for each digit are as follows.

(Pattern for 3 digits on the right)
Characters Q, X, Z, /, or  cannot be displayed.
(Pattern for 1 digit on the left)

Characters A to Z can be displayed (the same as the 3 digits on the right).
-44-
●Special function setting
■[F90] Setting of all functions
All functions can be set in turn.
<Operation>
Press the button. Move on to setting of all functions.
Setting of all functions

Press the or button to select all functions.
[on](use) is selected
[oFF] (not use) is
selected Setting of functions 
Press the
button to set. Return to [oFF](not used), then
press the button to set. Press the
Return to function button for 2
selection mode. Return to function selection second or longer.
mode.
[F90] Setting of all functions completed Measurement mode
: Setting of each function

Every time the button is pressed, the display moves to the next function in order of "Setting of each function" on page 46.
Set by using the and buttons.
For details of how to set each function, refer to the relevant setting of function section in this manual.
-45-
●Setting of each function
Order Function
1 Display unit selection
2 Output mode setting of OUT1
3 Reversed output setting of OUT1
4 Pressure setting of OUT1
5 Hysteresis setting of OUT1
6 Delay time setting of OUT1
7 Display colour setting
8 Digital filter setting
9 Auto-preset function
10 Fine adjustment of display value
11 Sub display setting
12 Display resolution setting
13 Power saving mode
14 Security code
15 Input of line name
: Measurement mode can return from any setting item by pressing the button for 2 seconds or longer.
: Function set before returning to the measurement mode is maintained.
-46-
■[F98] Output check
Correct operation of the switch output can be confirmed.
The output can be turned ON/OFF manually.
<Operation>
Press the button. Move on to output check.
Output check
Press the or button to select output check.
[F] (Forced output) is selected
[n] (Normal Press the button to set.

output) is
selected
OUT1 output check
Press the
Press the or button to select OUT1
button
output check.
to set.
Return to
function
selection mode.
Press the
button to return to
[n](normal output),
then press the Press the button
button to set. for 2 second or longer.
Return to function
selection mode.
[F98] Output check completed Measurement mode
: Measurement mode can return from any setting item by pressing the button for 2 seconds or longer.
-47-
■[F99] Reset to default settings
If the product settings are uncertain, the default values can be restored.
<Operation>
Press the button. Move on to reset to default settings.
Reset to default settings

Press the or button to display [ON], then press the
and buttons simultaneously for 5 second or longer.
[oFF] (not use) is selected All settings are returned to the

default values. Return to
Press the button to set. function selection mode.
Return to function selection

mode.
[F99] Reset to default settings completed
-48-
Other Settings
○Snap shot function
The current pressure value can be stored to the switch output ON/OFF set point.
When the items of sub display (left) below are selected in 3 step setting mode, simple setting mode or
function selection mode ([F 1] Setting of OUT1), by pressing the and buttons simultaneously for
1 second or longer, the value of the sub display (right) shows [- - -], and the values corresponding to the
current pressure values are automatically displayed.
Output mode Configurable items Sub display (left) Snap shot function
OUT1 set value ( ) ○
Hysteresis mode
Hysteresis ○
OUT1 set value ( ), ( ) ○
Hysteresis x
•OUT1 set value

The value is set to the same value as the display value (current pressure value).
(There is a range which cannot be set to the current pressure depending on the hysteresis. In that case, the
value is set to the closest value.)
•Hysteresis
The hysteresis is calculated from the equation below and set.
Normal output: (OUT1 set value) - ( current pressure value)
Reverse output: (current pressure value) - (OUT1 set value)
If the calculation result becomes 0 or less, [Err] is displayed on the sub display (right) and the set value is
not changed.
Afterwards, it is possible to adjust the value by pressing the or button.
○Peak/bottom value indication

The maximum (minimum) pressure when the power is supplied is detected and updated.
In peak/bottom indication mode, the current pressure is displayed.
Press the or button in measurement mode to switch the sub-display (left) to the display shown
below.
Peak/bottom values are displayed on the sub display (right) at the same time as the current pressure value
on the main display.
Peak/bottom values are maintained even if the power supply is cut.

When the and buttons are pressed for 1 second or longer simultaneously while the peak/bottom
values are displayed, the sub display (right) displays [- - -] and the maximum (minimum) pressure value are
cleared.
○Zero-clear function
The displayed value can be adjusted to zero if the pressure being measured is within 7%F.S (3.5%F.S. for
compound pressure) of the zero point set at the time of default settings.
(The zero clear range varies by ±1%F.S. due to variation between individual products.)
In measurement mode, when the and buttons are pressed for 1 second or longer simultaneously,
the main display shows [- - -], and the reset to zero. The display returns to measurement mode
automatically.
-49-
○Key-lock function
The key-lock function is used to prevent errors occurring due to unintentional changes of the set values. If
the button is pressed while the keys are locked, [LoC] is displayed on the sub display (left) for
approximately 1 second.
(Each setting and peak/bottom values are displayed with and buttons.)
<Operation - Without security code input ->

(1) Press the button for 5 seconds or longer in measurement mode. When [oPE] is displayed on the
main display, release the button.
The current setting [LoC] or [UnL] will be displayed on the sub display.
(To release key-lock repeat the above operation.)
(2) Select the key-locking/un-locking with or button, and press the button to set.
-50-
<Operation – With security code input ->
•Locking
(2) Select the key [LoC] with or button, and press the button to set.
•Unlocking
(2) Select the un-locking [UnL] with or button. Setting is recognized by pressing the
button, then security code is required.
(3) For instructions on how to enter the security code, refer to "How to input and change the security
code" on page 52.
(4) If inputted security code is correct, the indication of the main display changes to [UnL], and pressing
the one of , or button releases key-lock and the measurement mode returns.
If the security code entered is incorrect, [FAL] will be displayed, and the security code must be entered
again. If the wrong security code is entered 3 times, [LoC] is displayed and the device returns to
measurement mode.
-51-
●How to input and change the security code
The left most digit starts flashing.
Press the or button to select a value.
Press the button to make the next digit to the right flash.
(If the button is pressed at the last digit, the first digit will start
flashing.)
After the setting is complete, Press and hold the button

for 1 second or longer.
(If an operation is not performed for 30 seconds during input or
change of the security code, it will return to measurement mode.)
-52-
Maintenance
How to reset the product after a power cut or forcible de-energizing
The setting of the product will be retained as it was before a power cut or de-energizing. The output condition
is also basically recovered to that before a power cut or de-energizing, but may change depending on the
operating environment. Therefore, check the safety of the whole installation before operating the product. If
the installation is using accurate control, wait until the product has warmed up (approximately 10 to 15
minutes).
Forgotten the security code

Use the procedure below when the security code has been forgotten.
<Operation>
Press the button for 5 seconds or longer in measurement mode. When [oPE] is displayed on the
Press the and buttons simultaneously for 5 second or longer.

: Display is not changed.
(If another operation is performed or no operation is performed for 30 seconds, the display will return to
measurement mode.)

[000] is displayed and the security code change mode is available.
(If an operation is not performed for 30 seconds, the display will return to measurement mode.)
Decide on the security code referring to "How to input and change the security code" on page 52.
When input is completed, the selected security code flashes.

After checking the security code is as required, press the button for 1 second or longer.
Return to measurement mode.
At this time, if the or buttons are pressed, any security code changes are lost, and the change
of security code must be repeated.
-53-
Troubleshooting
○Troubleshooting
Applicable pressure switch: ZSE20(F)/ISE20
When any failure occurs with this product, the following chart can be used to identify the cause of the failure.
If a cause applicable to the troubles cannot be identified and normal operation is recovered by replacement
with a new product, this indicates that the product itself was faulty. Problems with the product may be due to
the operating environment (installation etc). Please consult SMC.
The pressure switch The switch output does Refer to Trouble No.1
The operation light is
does not operate not turn OFF. ON.
normally.
The operation light is Product failure

OFF.
Yes
No Refer to Trouble No.2
The switch output The operation light is Product failure

stays OFF. ON.
The operation light Refer to Trouble No.1

stays OFF.
Refer to Trouble No.3
The switch output Refer to Trouble No.4

generates chattering.
The switch output

response is slow.
The operation light

does not operate Product failure
correctly.
Error is displayed. Refer to Trouble No.6
-54-
Displayed value is not The display is Refer to Trouble No.7
correct unstable.
The display turns OFF. Refer to Trouble No.8
The display is missing. Refer to Trouble No.8
Display flashes. Refer to Trouble No.9
There are differences

in the displayed values Refer to Trouble No.10
when using more than
one pressure switch.
The display accuracy

does not meet the
specifications.
The Display
measurement unit Refer to Trouble No.12
cannot be changed.
Buttons do not work. Refer to Trouble No.13
The body of the

pressure switch has Refer to Trouble No.14
become loose.
There is noise. Refer to Trouble No.15
-55-
○Troubleshooting list
Problem Problem possible
Problem Investigation method Countermeasures
No. causes
•The switch
output does not (1) Check the set pressure value.
turn OFF. (2) Check the settings of the (1) Adjust the set pressure
The operation operation mode, hysteresis and value.
Incorrect
light stays ON. output type. (2) Set the operation mode,
pressure setting
1 (In hysteresis mode or window hysteresis and output
•The switch comparator mode, and normal type again.
output does not output/ reversed output)
turn ON.
The operation
light stays OFF. Product failure Replace the product.
The switch Check the output wiring.

Check and correct the
output does not Incorrect wiring Check if the load is directly
wiring.
2 turn OFF. connected to DC(+) or DC(-).
The operation
light is normal. Product failure Replace the product.
Check the output wiring.

Incorrect wiring Check if the load is directly
wiring.
connected to DC(+) or DC(-).
Check if PNP output is used when

The switch Revise the model selection
Model selection NPN should have been selected, or
output is OFF. (output specification).
3 the other way around.
The operation
light is normal. Check if there is bending stress Correct the wiring.
applied to any part of the lead wire. (Reduce the tensile force or
Lead wire broken
(bending radius, tensile force to the increase the bending
lead wire) radius.)
Product failure Replace the product.

Check the wiring.
Check if the brown and blue wires are
Correct the connection on
Incorrect wiring connected to DC(+) and DC(-)
the power cord and the plug.
respectively, and if the output line is
secure (contact failure).
The switch
4 output generates (1) Check the set pressure value.
(1) Adjust the set pressure
chattering. (2) Check if the hysteresis range is
value.
Incorrect small.
(2) Make the hysteresis
pressure setting (3) Check the delay time setting.
wider.
Check if the delay time is too
(3) Set the delay time again.
short.
Adjust the set pressure
Check the set pressure value.
The switch value .Ensure the set
Incorrect Check if the detected pressure and
5 output response pressure value is not too
pressure setting the set pressure values are the same
is slow. close to the detected
or are too close.
pressure value.
-56-
No. causes
(1) Check if the output current is 80
(1)(2) Connect the
mA or more.
appropriate load.
(2) Check if the connected load
(3) Use a relay with a surge
complies with the specification.
Excess current voltage suppressor or
Check if the load is short circuited.
was applied to take measures to prevent
(3) Check if the relay without surge
the output (Er1) surge.
protection is connected.
(4) Separate the wiring from
(4) Check if the wiring is in the same
the high-voltage and/or
route as (or bundled together
power line.
with) a high-voltage or power line.
•Over current (1) Remove the noise and

(1) Check if there is noise
error (Er1) is the noise source (or take
interference (such as static
displayed. Incorrect internal measures to prevent
electricity).
data processing noise interference), and
Check if there is a noise source
•System error of the product reset the product (or turn
nearby.
(Er0, 4, 6, 7, 8, (Er0, 4, 6, 7, 8 off and then turn back on
(2) Check if the power supply voltage
9) is displayed. and 9) the power supply.
is in the range 12 to 24 VDC
(2) Supply power in the range
±10%.
•"HHH" is 12 to 24 VDC ±10%.
6
displayed.
(1) Reset applied pressure to
(1) Check if the pressure exceeds the
a level within the set
•"LLL" is Applied pressure upper limit of the set pressure
pressure range.
displayed. is higher than the range.
(2) Take measures to
upper limit (HHH) (2) Check if foreign matter has
prevent foreign matter
• Residual entered the piping.
from entering the piping.
pressure error
(Er3) is (1) Reset applied pressure to
(1) Check if the pressure exceeds the
displayed. a level within the set
Applied pressure lower limit of the set pressure
pressure range.
is lower than the range.
(2) Take measures to
lower limit (LLL) (2) Check if foreign matter has
prevent foreign matter
entered the piping.
from entering the piping.
Pressure is not
Check if the pressure exceeded the Release the applied
atmospheric
atmospheric pressure within ±7% pressure to atmospheric
pressure when
F.S. (±3.5% F.S. for compound pressure, and retry the zero
zero-clear is
pressure). clear operation.
performed (Er3)
Incorrect power Check if the power supply voltage is Supply power in the range
supply in the range 12 to 24 VDC ±10%. 12 to 24 VDC ±10%.
Check the power supply wiring.
Check if the brown and blue wires are Check and correct the
Incorrect wiring
connected to DC(+) and DC(-) wiring.
respectively, and if the wiring is secure.
The display is
7
unstable. If the fluctuation is not
acceptable, the number of
Factory line digits (display sensitivity)
Check if the factory line pressure is
pressure is not can be reduced by changing
changing.
stable the display resolution.
Digital filter setting may
improve the condition.
-57-
No. causes
Incorrect power Check if the power supply voltage is Supply power in the range
supply in the range 12 to 24 VDC ±10%. 12 to 24 VDC ±10%.
•The display Check the power supply wiring.

turns OFF. Check if the brown and blue wires are
Incorrect wiring connected to DC(+) and DC(-)
8 wiring.
•Part of the respectively, and if the wiring is
display is secure.
missing.
Power saving Check if power saving mode is Select the power saving
mode selected. mode again.
(1) Check the power supply wiring. (1) Check and correct the
(2) Check if there is bending stress wiring.
9 Display flashes. Incorrect wiring
applied to any part of the lead (2) Correct the wiring (bend
wire. radius and stress).
Pressure display Use the fine adjustment

Variation within
is unstable when Check if the variation is within the mode to adjust the display if
the display
10 products are in display accuracy range. the variation is within the
accuracy range
close proximity to display accuracy range.
each other.
Use 5 m of filter to prevent
foreign matter from entering
Foreign matter Confirmed foreign matter entry or
or sticking. Discharge the
entered sticking to the piping port.
condensate of the filter
periodically.
Rework the piping.

If the tightening torque is
The display
Air or liquid Check if air or liquid are leaking from exceeded, the mounting
accuracy does
11 leakage the piping. screws, brackets and the
not meet the
pressure switch may be
specifications.
damaged.
After energizing, the display

Check if the product satisfies the and output can drift. For
Warming up
specified accuracy 10 minutes after precise pressure detection,
inadequate
supplying power. allow the product to warm up
for 10 to 15 minutes.
Unit s selection function is

not available for fixed to SI
Model selection
units type.
Display (model selected Check if the product number printed
(kPaMPa is available)
measurement does not have on the product indicates units
12 : The units selection function is
unit cannot be units selection selection function type.
not for use in Japan due to a
changed. function)
new measurement law.
: Fixed to SI units: kPa, MPa
-58-
No. causes
Key-lock mode is Check if the key-lock function is
Buttons do not Check the key-lock function.
13 activated turned on.
work.
The body of the Imperfect Confirm that the product is properly in Mount the body on the panel
pressure switch installation panel mount adapter claws. mount.
14
has become
loose. Product failure Replace the product.
Rework the piping.

If the tightening torque is
Air or liquid Check if air or liquid are leaking from exceeded, the mounting
15 There is noise. leakage the piping. screws, brackets and the
pressure switch may be
damaged.
Effect of line
pressure
fluctuation (1) Adjust the set pressure
(1) Check the set pressure values
because value.
(hysteresis)
hysteresis is too (2) Change the response
(2) Check the delay time.
narrow or delay time setting.
time of the switch
The operation is
is too short
16 unstable.
(chattering) (1) Check the power supply wiring. (1) Check and correct the
(2) Check if there is bending stress wiring.
Incorrect
applied to any part of the lead (2) Correct the wiring.
wiring/broken
wire. (Reduce the tensile force
lead wire
(bending radius, tensile force to or increase the bending
the lead wire) radius.)
-59-
○Error indication function
This function is to display error location and content when a problem or error has occurred.
Error Error displayed Description Measures
Turn the power off and remove

Over current The switch output load current is 80 mA
the cause of the over current.
error or more.
Then supply the power again.
During zero clear operation, pressure

greater than ±7% F.S. (±3.5% F.S.for
compound pressure) is present. Note
Release the applied pressure to
Residual that the mode is returned to
atmospheric pressure, and retry
pressure error measurement mode automatically 1
the zero clear operation.
second later. The zero clear range
varies by ±1% F.S. due to variation
between individual products.
Pressure exceeding the upper limit of

the set pressure range is applied.
Pressurizing Reset applied pressure to a level
error within the set pressure range.
Pressure exceeding the lower limit of
the set pressure range is applied.
Turn the power off and on again.

Displayed if an internal data error has
System error If the failure cannot be solved,
occurred.
contact SMC.
If the error cannot be reset after the above measures are taken, or errors other than above are displayed,
please contact SMC.
-60-
Specification
■Specifications
ZSE20 ZSE20F ISE20
Product No.
(Vacuum pressure) (Compound pressure) (Positive pressure)
Applicable fluid Air, non-corrosive gas and non-flammable gas
Rated pressure range 0.0 to -101.0 kPa -100.0 to 100.0 kPa -0.100 to 1.000 MPa
Pressure
spec.
Set pressure range 10.0 to -105.0 kPa -105.0 to 105.0 kPa -0.105 to 1.050 MPa
Min. setting unit 0.1 kPa 0.001 MPa
Proof pressure 500 kPa 1.5 MPa
Power supply voltage 12 to 24 VDC10%, ripple max. 10% (p-p)
Electric
spec.
Current consumption 25 mA or less

Protection Polarity protection
Display accuracy 2%F.S. 1 digit (at ambient temperature 253 oC)
Accuracy
Repeatability 0.2%F.S. 1 digit

Temperature characteristics 2%F.S. (25 oC standard)
Output type NPN or PNP open collector 1 output
Hysteresis mode, window comparator mode, error output,
Output mode
switch output off
Switch operation Normal output, reversed output
Maximum load current 80 mA
Maximum applied voltage
28 V
Switch output
(NPN output)
Internal voltage drop
1 V or less (Load current 80 mA)
(Residual voltage)
1.5 ms or less (delay time available for anti-chattering function:
Delay time 1
20,100,500,1000,2000 or 5000 ms)
Hysteresis
Hysteresis mode
Variable from 0 2
Short circuit protection Provided

MPa, kPa, kgf/cm2,
Unit 3 MPa, kPa, kgf/cm2, bar, psi, InHg, mmHg
bar, psi
Display type LCD
Number of displays 3-screen display (Main display, sub display x 2)
Display
1) Main display: Red/Green

Display colour
2) Sub display: Orange
Main display: 4 digit (7-segments)
Number of display digits
Sub display: 4 digit (Upper 1 digit 11-segments, 7-segments for other)
Operation light LED is ON when switch output is ON (OUT1: Orange)
4
Digital filter 0, 10, 50, 100, 500, 1000, 5000 ms
-61-
ZSE20 ZSE20F ISE20
Product No.
(Vacuum pressure) (Compound pressure) (Positive pressure)
Enclosure IP40
Environment
Withstand voltage 1000 VAC for 1 minute between terminals and housing
Insulation resistance 50 MΩ or more between terminals and housing (with 500 VDC megger)
Operation: -5 to 50 oC, Storage: -10 to 60 oC
Ambient temperature range
(No condensation or freezing)
Operating humidity range Operation, Storage: 35 to 85%RH (No condensation)
Standard CE, RoHS
Length of lead wire with connector 2m
1: Value without digital filter (at 0 ms).
2: If the applied pressure fluctuates around the set value, the hysteresis must be set to a value more than the amount of fluctuation or
chattering will occur.
3: This setting is only available for models with the units selection function. Only MPa or kPa is available for models without this function.
4: The response time indicates when the set value is 90% in relation to the step input.
○Cable specifications
Conductor area 0.15 mm2 (AWG26)
Insulator
Outside diameter 1.0 mm
Colour Brown, Blue, Black (3 core)

Sheath
Finished outside diameter 3.4
○Piping/weight specifications
Product No. M5 01 N01
Port size M5 x 0.8 R1/8 NPT1/8
Pressure-sensing part Silicon
fluid contact
Materials in
Piping port (Common) PBT, CB156, heat resistant PPS, O-ring: HNBR
part
C3604 (Electroless nickel plating), SUS304,

Piping port -
NBR
Weight
Body 22 g 32 g 34 g
Lead wire with connector +35 g
-62-
■Dimensions
M5 type
01/N01 type
Piping specifications Port size A

01 R1/8 Width across flats 10
N01 NPT1/8 Width across flats 12
-63-
○Bracket mounting dimensions
●Bracket A
●Bracket B
-64-
○Mounting dimensions of panel mount adapter
○Mounting dimension of panel mount adapter + Front protective cover
-65-
○Panel cutout dimensions
Mount individually
More than 2 pcs. (n pcs.) Close mounting
<Horizontal> <Vertical>
-66-
Revision history
A: Contents revised in several places.
B: Contents revised in several places.
[September 2016]
4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN

Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362
URL http://www.smcworld.com
Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.
© 2015-2016 SMC Corporation All Rights Reserved

PSXX OMS0007 B PDF

Uploaded by

Copyright:

Available Formats

PSXX OMS0007 B PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PSXX OMS0007 B PDF

Uploaded by

Copyright:

Available Formats

No.

Digital Pressure Switch

MODEL / Series / Product Number

Limited warranty and Disclaimer/Compliance Requirements

Limited warranty and Disclaimer

■Do not operate the product outside of the specifications.

■Do not operate in an atmosphere containing flammable or explosive gases.

■If using the product in an interlocking circuit:

■The following instructions must be followed during maintenance:

Adjustment and Operation

Operation light: Displays the switch operating condition.

E The code number displayed, identifying the error detected by the

Switches the switch output to ON/OFF when an error is displayed.

A mode in which setting of functions is performed. It is a separate menu from

Variation in repeated measurement of pressure display or ON-OFF output

A measure of the product’s resistance to a voltage applied between the

•Bracket A (Part No.: ZS-46-A1)

•Bracket B (Part No.: ZS-46-A2)

How to remove the panel mount adapter

●Piping specification: -01, -N01

When tightening, do not hold the Z/ISE20 body with a spanner.

○How to use connector

Connector pin numbers

Press the Press the

: The outputs will continue to operate during setting.

(2) Press the or button to change the set value.

(3) Press the button to complete the setting.

●[F 0] Units selection function Page 27

●[F 1] Setting of OUT1 Page 28

ISE20 : 0.050 MPa

Press the button. Move on to display unit selection.

Display unit selection

Press the button to set. Return to function selection mode.

[F 0] Units selection function completed

●Available display unit and minimum set value

Press the button. Move on to output mode setting.

Output mode setting

Press the button to set. Move on to reversed output setting.

Reversed output setting

[OFF] Output off is

Press the button to set. Move on to hysteresis setting.

Hysteresis mode: [H_1]

Press the button to set. Move on to delay time setting.

Delay time setting

Press the button to set. Move on to display colour setting.

Display colour setting

Press the button to set. Return to function selection mode.

[F 1] Setting of OUT1 completed

1: Selected item becomes valid after pressing the button.

: Applicable errors are Er0, 4 to 6, 8, and 9.

Press the button. Move on to digital filter setting.

Digital filter setting

Press the button to set. Return to function selection mode.

[F 3] Digital filter setting completed

1: Each set value is a guideline for 90% response time.

Press the button. Move on to Auto-preset function.

Press the button to set. Return to function selection mode.

[F 4] Auto-preset function completed

Press the button in measurement mode to perform the pressure setting.